List of standards DIN 1500 to DIN 1999

Logo of the German Institute for Standardization

The list of standards DIN 1500 to DIN 1999 lists all current standards and many historical standard editions in the number range 1500 to 1999.

DIN - German Institute for Standardization e. V. - is the national standardization organization of the Federal Republic of Germany based in Berlin .

Explanations of the list

DIN-EN standards, DIN-EN-ISO standards, DIN-ISO standards, preliminary standards and draft standards are not listed in this list.
The term “sheet” used in older standard editions has been uniformly transferred to “part”.
The date of issue is indicated next to the standard number. Edition 9.1981 means that the standard was published in September 1981.
Cross edition: If the date of issue is appended with an x, for example edition 9.1949x, the standard has only been changed slightly and remains valid.
Unless otherwise noted, the withdrawal date of an old standard is the same as the issue date of the replacing standard (s).
The entry "→ current" means that the standard is currently (as of June 2017) valid.

DIN 1500 · Edition 5.1971 → withdrawn

Forms for public libraries

DIN 1501 edition 9.1975 → withdrawn

Magazines · classification mark on the outer cover

DIN 1502 edition 1.1984 → withdrawn

Rules for shortening words in titles and for shortening the titles of publications

DIN 1502 edition 12.1975 → replaced by edition 1.1984

Shortening the titles of magazines and similar publications · Rules

DIN 1502 - supplement 1 edition 12.1975 → withdrawn

Abbreviations of the titles of magazines and similar publications. Abbreviations of words from languages with Latin and Cyrillic characters

DIN 1503 edition 9.1971 → withdrawn

Design of academic and professional journals

DIN 1504 edition 5.1973 → withdrawn

Literature cards

DIN 1505 - Part 2 Edition 1.1984 → replaced by DIN ISO 690 Edition 10.2013

Titles of documents · Citation rules

DIN 1505 - Part 3 · Edition 12.1995 → withdrawn

Title references of documents Lists of cited documents (bibliographies)

DIN 1505 edition 12.1961 → replaced by DIN 1505 part 2 edition 1.1984

Title references from literature

DIN 1506 edition 3.1978 → current

Format for the exchange of bibliographic data

DIN 1530 - Part 1 · Edition 5.2011 → current

Press, injection molding and die casting tools · Ejector pins with cylindrical head

The standard applies to ejector pins with a cylindrical head for ejecting molded parts from compression, injection molding or die casting tools

DIN 1530 - Part 2 · Edition 5.2011 → current

Press, injection molding and die casting tools · Stepped ejector pins

The standard applies to offset ejector pins for ejecting molded parts from press, injection molding or die casting tools

DIN 1530 - Part 3 · Edition 5.2011 → current

Press, injection molding and die casting tools · Ejector pins with conical head

The standard applies to ejector pins with a tapered head for ejecting molded parts from press, injection molding or die casting tools

DIN 1541 edition 8.1975 → replaced by DIN EN 10131 edition 1.1992

Flat goods made of steel · Cold rolled wide strip and sheet metal made of unalloyed steels · Dimensions, permissible dimensional and shape deviations

DIN 1542 edition 4.1959 → replaced by DIN 1543 edition 10.1981

Sheet steel from 3 to 4.75 mm (middle sheet) · Thicknesses, sizes, dimensional and weight deviations

DIN 1543 edition 10.1981 → replaced by DIN EN 10029 edition 10.1991

Flat products made of steel · Hot-rolled sheet metal from 3 to 150 mm thick · Permissible dimensional, weight and shape deviations

DIN 1544 edition 8.1975 → replaced by DIN EN 10140 edition 10.1996

Flat goods made of steel · Cold-rolled steel strip · Dimensions, permissible dimensional and shape deviations

DIN 1546 Edition 6.1954 → current

Diamond drawing dies for wires made of ferrous and non-ferrous metals

DIN 1547 - Part 1 Edition 7.1969 → current

Carbide drawing dies and drawing rings · Terms, designation, marking

DIN 1547 - Part 2 Edition 7.1969 → current

Carbide drawing dies and dies · Drawing dies for steel wire

DIN 1547 - Part 3 Edition 7.1969 → current

Carbide drawing dies and drawing rings · Drawing dies for wires made of non-ferrous metals

DIN 1547 - Part 4 Edition 7.1969 → current

Carbide drawing dies and drawing rings · Drawing rings for round steel

DIN 1547 - Part 5 Edition 7.1969 → current

Carbide drawing dies and drawing rings · Drawing rings for round bars made of non-ferrous metals

DIN 1547 - Part 6 Edition 7.1969 → current

Carbide drawing dies and drawing rings · Drawing rings for steel pipes

DIN 1547 - Part 7 Edition 7.1969 → current

Carbide drawing dies and drawing rings · Drawing rings for pipes made of non-ferrous metals

DIN 1547 - Part 8 Edition 7.1969 → current

Carbide drawing dies and drawing rings · Drawing rings for square and flat steel

DIN 1547 - Part 9 Edition 7.1969 → current

Carbide drawing dies and drawing rings · Drawing rings for square and flat bars made of non-ferrous metals

DIN 1547 - Part 10 Edition 7.1969 → current

Carbide drawing dies and drawing rings · Drawing rings for hexagonal steel

DIN 1547 - Part 11 Edition 7.1969 → current

Carbide drawing dies and drawing rings · Drawing rings for hexagonal bars made of non-ferrous metals

DIN 1552 - Part 1 · Edition 6.2008 → current

Bushings for rail vehicles · Press-in bushings made of steel

DIN 1552 - Part 1 · Edition 7.1987 → replaced by Edition 6.2008

Bushings for rail vehicles · Press-in bushings made of steel

DIN 1552 - Part 1 · Edition 1.1983 → replaced by Edition 7.1987

Bushings for rail vehicles · Press-in bushings made of steel

DIN 1552 - Part 2 · Edition 6.2008 → current

Bushings for rail vehicles · Press-on bushes made of steel

DIN 1552 - Part 2 · Edition 7.1987 → replaced by Edition 6.2008

Bushings for rail vehicles · Press-on bushes made of steel

DIN 1552 - Part 2 · Edition 1.1983 → replaced by Edition 7.1987

Bushings for rail vehicles · Press-on bushes made of steel

DIN 1552 - Part 3 · Edition 6.2008 → current

Bushings for rail vehicles · Crowned press-in bushings made of steel

DIN 1552 - Part 3 · Edition 12.1991 → replaced by Edition 6.2008

Bushings for rail vehicles · Crowned press-fit bushes made of steel

DIN 1552 - Part 4 · Edition 6.2008 → current

Bushings for rail vehicles · Press-in bushings made of steel with special dimensional accuracy

DIN 1554 edition 5.1989 → current

Rail vehicles · Raw wheel tires · Width 138 and 143 mm · Raw dimensions

DIN 1554 edition 4.1980 → replaced by edition 5.1989

Raw wheel tires for rail vehicles, width 138 and 143 mm · raw dimensions

DIN 1564 edition 11.1997 → withdrawn

Steel fittings for rail vehicles · Sleeves, reducing sleeves

DIN 1564 edition 4.1974 → replaced by edition 11.1997

Steel fittings for rail vehicles · Sleeves, transition sleeves

DIN 1565 edition 11.1997 → current

Steel fittings for rail vehicles · Pipe nipple, pipe double nipple, reducing nipple

DIN 1565 edition 4.1974 → replaced by edition 11.1997

Steel fittings for rail vehicles · Pipe nipple, pipe double nipple, transition nipple

DIN 1566 edition 11.1997 → withdrawn

Steel fittings for rail vehicles · Double nipple, reducing double nipple

DIN 1566 edition 4.1974 → replaced by edition 11.1997

Steel fittings for rail vehicles · Double nipple, transition double nipple

DIN 1567 edition 11.1997 → withdrawn

Steel fittings for rail vehicles T, reducing T

DIN 1567 edition 4.1974 → replaced by edition 11.1997

Steel fittings for rail vehicles · T-pieces, transition T-pieces

DIN 1568 edition 11.1997 → withdrawn

Steel fittings for rail vehicles · Crosses

DIN 1568 · edition 4.1974 → replaced by edition 11.1997

Steel fittings for rail vehicles · Cross pieces

DIN 1569 edition 11.1997 → withdrawn

Steel fittings for rail vehicles · Elbows, Y-pieces

DIN 1569 · edition 4.1974 → replaced by edition 11.1997

Steel fittings for rail vehicles · Elbow pieces, trouser pieces

DIN 1570 edition 2.1979 → replaced by DIN EN 10092 part 2 edition 1.2004

Hot-rolled, ribbed spring steel · Dimensions, weights, permissible deviations, static values

DIN 1578 Edition 3.1979 → current

Snap rings for wheel tires

DIN 1581 edition 12.1977 → withdrawn

Steel bars · Joint hinge profiles, dimensions, weights

DIN 1587 edition 7.2014 → current

Hexagon cap nuts, tall shape

The standard specifies requirements for hexagon cap nuts with a tall shape of sizes M4 to M24.

DIN 1587 edition 10.2000 → replaced by edition 7.2014

Hexagon cap nuts, tall shape

Correction of edition 2.2000

DIN 1587 edition 2.2000 → replaced by edition 10.2000

Hexagon cap nuts, tall shape

DIN 1587 edition 6.1987 → replaced by edition 2.2000

Hexagon cap nuts, tall shape

DIN 1587 edition 4.1977 → replaced by edition 6.1987

Hexagon cap nuts, tall shape

DIN 1588 · Edition 5.1991 → current

Rail vehicles · Step-grip units · Construction information

DIN 1592 edition 2.1988 → current

Heavy steel pipe clamps, single-loop with tightening option for rail vehicles

DIN 1592 edition 12.1976 → replaced by edition 2.1988

Heavy pipe clamps with tightening option, single-loop, for rail vehicles

DIN 1593 Edition 2.1988 → current

Heavy steel pipe clamps, two-lashed with tightening option for rail vehicles

DIN 1593 edition 12.1976 → replaced by edition 2.1988

Heavy pipe clamps with tightening option, two-lashed, for rail vehicles

DIN 1595 edition 5.1978 → withdrawn

Knobs, knob screws for rail vehicles

DIN 1596 edition 2.1988 → current

Light pipe clamps made of steel, single-loop with tightening option for rail vehicles

DIN 1596 edition 12.1976 → replaced by edition 2.1988

Light pipe clamps with tightening option, single-loop, for rail vehicles

DIN 1597 edition 2.1988 → current

Light pipe clamps made of steel, two-lashed with tightening option for rail vehicles

DIN 1597 edition 12.1976 → replaced by edition 2.1988

Light pipe clamps with tightening option, two-lashed, for rail vehicles

DIN 1599 edition 8.1980 → current

Types of marking for steel

DIN 1623 edition 5.2009 → current

Cold-rolled strip and sheet · Technical delivery conditions · General structural steels

DIN 1623 - Part 2 · Edition 2.1986 → replaced by DIN 1623 Edition 5.2009

Flat products made of steel · Cold rolled strip and sheet · Technical delivery conditions · General structural steels

DIN 1623 - Part 2 · Edition 1.1961 → replaced by Edition 2.1986

Thin sheets made of unalloyed steels · Thin sheets made of general structural steels · Quality regulations

DIN 1653 edition 1.1979 → current

Surface quality of commercially available steel wires · Names and their abbreviations

DIN 1683 - part 1 edition 8.1998 → replaced by DIN CEN ISO / TS 8062 part 2 edition 3.2014 and DIN SPEC 91184 edition 3.2014

Unfinished cast steel parts · General tolerances, machining allowances · Not for new designs

DIN 1683 - Part 1 · Edition 10.1980 → replaced by Edition 8.1998

Cast steel parts · General tolerances, machining allowances

DIN 1686 - Part 1 Edition 8.1998 → replaced by DIN CEN ISO / TS 8062 Part 2 Edition 3.2014 and DIN SPEC 91184 Edition 3.2014

Cast blanks made of cast iron with lamellar graphite · General tolerances, machining allowances · Not for new designs

DIN 1686 - part 1 edition 10.1980 → replaced by edition 8.1998

Unfinished cast iron parts with flake graphite · General tolerances, machining allowances

DIN 1687 - part 1 edition 8.1998 → replaced by DIN CEN ISO / TS 8062 part 2 edition 3.2014 and DIN SPEC 91184 edition 3.2014

Raw castings made of heavy metal alloys · Sand casting · General tolerances, machining allowances · Not for new designs

DIN 1687 - part 1 edition 10.1980 → replaced by edition 8.1998

Raw castings made from heavy metal alloys · Sand castings · General tolerances, machining allowances

DIN 1687 - Part 1 edition 8.1974 → replaced by edition 10.1980

Unfinished castings made of heavy metal alloys · Free dimensional tolerances · Sand casting

DIN 1687 - Part 3 Edition 10.1980 → replaced by DIN CEN ISO / TS 8062 Part 2 Edition 3.2014 and DIN SPEC 91184 Edition 3.2014

Raw castings made from heavy metal alloys · Chill casting · General tolerances, machining allowances

DIN 1687 - Part 4 Edition 8.1986 → replaced by DIN CEN ISO / TS 8062 Part 2 Edition 3.2014 and DIN SPEC 91184 Edition 3.2014

Raw castings made from heavy metal alloys · Die casting · General tolerances, machining allowances

DIN 1687 - Part 4 Edition 8.1974 → replaced by Edition 8.1986

Raw castings made of heavy metal alloys · Free dimensional tolerances · Die casting

DIN 1688 - part 1 edition 8.1998 → replaced by DIN CEN ISO / TS 8062 part 2 edition 3.2014 and DIN SPEC 91184 edition 3.2014

Castings made of light metal alloys · Sand castings · General tolerances, machining allowances · Not for new designs

DIN 1688 - Part 1 · Edition 10.1980 → replaced by Edition 8.1998

Castings made of light metal alloys · Sand castings · General tolerances, machining allowances

DIN 1688 - Part 3 Edition 10.1980 → replaced by DIN CEN ISO / TS 8062 Part 2 Edition 3.2014 and DIN SPEC 91184 Edition 3.2014

Castings made of light metal alloys · Chill casting · General tolerances, machining allowances

DIN 1688 - Part 4 Edition 8.1986 → replaced by DIN CEN ISO / TS 8062 Part 2 Edition 3.2014 and DIN SPEC 91184 Edition 3.2014

Castings made of light metal alloys · Die casting · General tolerances, machining allowances

DIN 1688 - Part 4 Edition 8.1974 → replaced by Edition 8.1986

Castings made of light metal alloys · Free dimensional tolerances · Die casting

DIN 1700 edition 7.1954 → withdrawn

Non-ferrous metals · System of symbols

DIN 1701 edition 5.1980 → current

Smelting nickel

DIN 1702 edition 1.1967 → current

Nickel anodes

DIN 1705 edition 11.1981 → replaced by DIN EN 1982 edition 12.1998

Copper-tin and copper-tin-zinc cast alloys (cast tin bronze and gunmetal) · Castings

DIN 1705 - supplement 1 edition 11.1981 → replaced by DIN EN 1982 edition 12.1998

Copper-tin and copper-tin-zinc cast alloys (cast tin bronze and gunmetal) · Castings · Guide information on mechanical and physical properties

DIN 1707 - Part 100 · Edition 9.2011 → current

Soft solders · Chemical composition and delivery forms

The standard contains the chemical compositions of 27 alloys as well as further requirements and delivery forms.

DIN 1707 - Part 100 · Edition 2.2001 → replaced by Edition 9.2011

Soft solders · Chemical composition and delivery forms

DIN 1707 - Part 100 edition 2.1981 → replaced by edition 2.2001 and DIN EN 29453 edition 2.1994

Soft solders · Composition, use, technical delivery conditions

DIN 1708 edition 1.1973 → replaced by DIN EN 1976 and DIN EN 1978 edition 5.1998

Copper · Cathodes and cast formats

DIN 1709 edition 11.1981 → replaced by DIN EN 1982 edition 12.1998

Copper-zinc cast alloys (cast brass and special cast brass) · Castings

DIN 1709 - supplement 1 edition 11.1981 → replaced by DIN EN 1982 edition 12.1998

Copper-zinc cast alloys (cast brass and special cast brass) · Castings · Guide information on mechanical and physical properties

DIN 1709 edition 6.1973 → replaced by edition 11.1981

Copper-zinc cast alloys (cast brass and special cast brass) · Castings

DIN 1714 edition 11.1981 → replaced by DIN EN 1982 edition 12.1998

Copper-aluminum cast alloys (cast aluminum bronze) · Castings

DIN 1714 - supplement 1 edition 11.1981 → replaced by DIN EN 1982 edition 12.1998

Copper-aluminum cast alloys (cast aluminum bronze) · Castings · Guide information on mechanical and physical properties

DIN 1715 - Part 1 Edition 11.1983 → current

Thermobimetals · Technical delivery conditions

DIN 1715 - Part 2 Edition 11.1983 → current

Thermal bimetals · Testing of specific thermal curvature

DIN 1715 edition 7.1963 → replaced by DIN 1715 part 2 edition 11.1983

Thermal bimetals

DIN 1716 edition 11.1981 → replaced by DIN EN 1982 edition 12.1998

Copper-lead-tin-cast alloys (cast-tin-lead-bronze) · castings

DIN 1716 - supplement 1 edition 11.1981 → replaced by DIN EN 1982 edition 12.1998

Copper-lead-tin-cast alloys (cast-tin-lead-bronze) · Castings · Guide information about mechanical and physical properties

DIN 1718 edition 11.1959 → withdrawn

Copper alloys · Terms

DIN 1729 - Part 1 Edition 8.1982 → current

Magnesium alloys · wrought alloys

DIN 1732 - Part 3 · Edition 6.2007 → current

Welding consumables for aluminum and aluminum alloys · Test pieces, specimens, mechanical-technological minimum values of the pure weld metal

DIN 1732 - Part 3 · Edition 6.1988 → replaced by Edition 6.2007

Welding consumables for aluminum and aluminum alloys · Test pieces, specimens, mechanical-technological minimum values of the pure weld metal

DIN 1742 edition 7.1971 → current

Tin Die Casting Alloys · Die Castings

DIN 1754 - Part 1 edition 8.1969 → replaced by DIN EN 12449 edition 10.1999, DIN EN 12451 edition 10.1999 and DIN EN 13600 edition 7.2002

Copper tubes, seamlessly drawn · Dimension ranges and tolerance assignments

DIN 1754 - Part 2 Edition 8.1969 → replaced by DIN EN 12449 Edition 10.1999 and DIN EN 13600 Edition 7.2002

Copper tubes, seamlessly drawn · Preferred sizes for general use

DIN 1754 - part 3 edition 4.1974 → replaced by DIN EN 12449 edition 10.1999

Copper pipes, seamless drawn · Preferred dimensions for pipes

DIN 1769 edition 9.1986 → replaced by DIN EN 754 part 5 edition 1.1996

Rectangular bars drawn from aluminum and wrought aluminum alloys, with sharp edges · Dimensions, dimensional and shape tolerances, static values

DIN 1769 · Edition 6.1974 → replaced by Edition 9.1986

Rectangular bars made of aluminum (pure aluminum, pure aluminum and wrought aluminum alloys), drawn, with sharp edges · Dimensions, permissible deviations, static values

DIN 1770 edition 1.1987 → replaced by DIN EN 755 part 5 edition 9.1995

Rectangular bars made of aluminum and wrought aluminum alloys, pressed · Dimensions, dimensional and shape tolerances, static values

DIN 1770 edition 9.1986 → replaced by edition 1.1987

Rectangular bars made of aluminum and wrought aluminum alloys, pressed · Dimensions, dimensional and shape tolerances, static values

DIN 1770 · Edition 6.1974 → replaced by Edition 9.1986

Rectangular bars made of aluminum (pure aluminum, pure aluminum and wrought aluminum alloys), pressed Dimensions, permissible deviations, static values

DIN 1786 edition 5.1980 → replaced by DIN EN 1057 edition 5.1996

Installation pipes made of copper, seamlessly drawn

DIN 1787 edition 1.1973 → withdrawn

Copper semi-finished products

DIN 1804 Edition 3.1971 → current

Locknuts · Metric ISO fine thread

DIN 1809 Edition 7.1961 → current

Driver on tools with straight shank

DIN 1810 edition 9.1979 → current

Hook wrench

DIN 1814 edition 2.1979 → current

Tap wrench, adjustable

DIN 1815 edition 12.2004 → current

Panel van with thermally insulated loading space for the transport of food · Requirements and tests

DIN 1815 edition 10.2003 → replaced by edition 12.2004

Panel van with thermally insulated loading space for the transport of food · Requirements and testing

DIN 1816 edition 3.1971 → current

Cross hole nuts · Metric ISO fine thread

DIN 1823 - Part 1 Issue 9.1978 → current

Angle milling cutter for tools · Dimensions

DIN 1823 - Part 2 · Edition 3.1992 → current

Angle milling cutter for tools · Technical delivery conditions

DIN 1823 - Part 2 · Edition 4.1990 → replaced by Edition 3.1992

Angle milling cutter for tools · Technical delivery conditions

DIN 1823 - Part 2 · Edition 12.1981 → replaced by Edition 4.1990

Angle milling cutter for tools · Technical delivery conditions

DIN 1823 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Angle milling cutter for tools · Technical delivery conditions

DIN 1825 edition 11.1977 → current

Cutting wheels for spur gears · Straight toothed disc cutting wheels

DIN 1826 edition 11.1977 → current

Cutter wheels for spur gears · Straight-toothed bell cutters

DIN 1828 edition 11.1977 → current

Cutting wheels for spur gears · Straight-toothed shaft cutting wheels

DIN 1829 - Part 1 · Edition 11.1977 → current

Cutting wheels for spur gears · Determining variables, terms, labeling

DIN 1829 - Part 2 Edition 11.1977 → current

Cutting wheels for spur gears · Tolerances, permissible deviations

DIN 1830 - Part 1 · Edition 6.1974 → current

Milling cutter heads with inserted knives, for internal centering, for mounting on milling spindle heads according to DIN 2079

DIN 1830 - Part 3 · Edition 6.1974 → current

Milling cutter heads with inserted knives, for mounting on shell mill arbors according to DIN 6361 and DIN 6362

DIN 1830 - Part 4 Edition 6.1974 → current

Milling cutter heads with inserted knives, for internal centering, with two hole circles, for mounting on milling spindle heads with steep taper No. 50 and 60 according to DIN 2079

DIN 1831 - Part 1 Edition 2.1986 → 6.2017 withdrawn without replacement

Side milling cutter with inserted blades · Dimensions

DIN 1831 - Part 2 Edition 4.1990 → 6.2017 withdrawn without replacement

Side milling cutters with inserted blades · Technical delivery conditions

DIN 1831 - Part 2 · Edition 6.1982 → replaced by Edition 4.1990

Side milling cutters with inserted blades · Technical delivery conditions

DIN 1833 - Part 1 · Edition 4.1989 → current

Angle milling cutter with parallel shank · Dimensions

DIN 1833 - Part 1 · Edition 10.1983 → replaced by Edition 4.1989

Angle milling cutter with parallel shank · Dimensions

DIN 1833 - Part 1 · Edition 9.1978 → replaced by Edition 10.1983

Angle milling cutter with parallel shank · Dimensions

DIN 1833 - Part 2 · Edition 4.1990 → current

Angle milling cutter with parallel shank · Technical delivery conditions

DIN 1833 - Part 2 · Edition 12.1981 → replaced by Edition 4.1990

Angle milling cutter with parallel shank · Technical delivery conditions

DIN 1833 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Angle milling cutter with parallel shank · Technical delivery conditions

DIN 1834 - Part 1 · Edition 1.1986 → current

Narrow side milling cutters · Dimensions

DIN 1834 - Part 2 · Edition 4.1990 → current

Narrow side milling cutters · Technical delivery conditions

DIN 1834 - Part 2 · Edition 1.1986 → replaced by Edition 4.1990

Narrow side milling cutters · Technical delivery conditions

DIN 1835 - Part 1 · Edition 1.1999 → current

Cylindrical shanks for milling cutters · Dimensions

DIN 1835 - Part 1 edition 1.1991 → replaced by edition 1.1999

Cylindrical shanks for milling cutters · Dimensions

DIN 1835 - Part 1 edition 12.1986 → replaced by edition 1.1991

Cylindrical shanks for milling cutters · Dimensions

DIN 1835 - part 1 edition 8.1978 → replaced by edition 12.1986

Cylindrical shanks for milling cutters · Dimensions

DIN 1835 - Part 2 Edition 11.2000 → current

Cylindrical shanks for milling cutters · Connection dimensions for chucks, accessories

DIN 1835 - Part 2 edition 12.1986 → replaced by edition 11.2000

Cylindrical shanks for milling cutters · Connection dimensions for chucks, accessories

DIN 1835 - Part 2 edition 8.1978 → replaced by edition 12.1986

Cylindrical shanks for milling cutters · Connection dimensions for chucks, accessories

DIN 1836 edition 1.1984 → current

Tool application groups for machining

DIN 1836 edition 8.1962 → replaced by edition 1.1984

Application areas for tool types N, H and W

DIN 1837 edition 8.1970 → current

Metal circular saw blades, fine-toothed

DIN 1838 edition 8.1970 → current

Metal circular saw blades, coarse-toothed

DIN 1840 edition 8.1970 → current

Metal circular saw blades · Tooth shapes, side free grinding, manufacturing accuracy

DIN 1850 - Part 1 Edition 10.1976 → replaced by DIN ISO 4379 Edition 10.1995

Bushings for plain bearings, made of copper alloys, solid

DIN 1850 - Part 2 edition 11.1982 → replaced by DIN ISO 12128 edition 7.1998

Plain bearings · Bushings with lubrication holes, lubrication grooves and lubrication pockets

DIN 1850 - Part 3 Edition 7.1998 → current

Plain bearings · Bushes made of sintered metal

DIN 1850 - Part 3 · Edition 6.1990 → replaced by Edition 7.1998

Plain bearings · Bushes made of sintered metal

DIN 1850 - Part 3 · Edition 4.1976 → replaced by Edition 6.1990

Bushings for plain bearings, made of sintered metal

DIN 1850 - Part 4 Edition 7.1998 → current

Plain bearings · Bushings made of synthetic carbon

DIN 1850 - Part 4 Edition 8.1970 → replaced by Edition 7.1998

Bushings for plain bearings, made of synthetic carbon

DIN 1850 - Part 5 Edition 7.1998 → current

Plain bearings · Bushings made of thermosetting plastics

DIN 1850 - Part 5 Edition 8.1975 → replaced by Edition 7.1998

Bushings for plain bearings, made of thermosetting plastics

DIN 1850 - Part 6 Edition 7.1998 → current

Plain bearings · Bushings made of thermoplastics

DIN 1850 - Part 6 Edition 2.1979 → replaced by Edition 7.1998

Bushings for plain bearings · Press-in bushings made from thermoplastics

DIN 1862 edition 1.1962 → current

Countersink for horizontal coordinate drilling machines (jig boring mills)

DIN 1863 Edition 1.1962 → current

Countersink for countersunk rivets

DIN 1864 edition 10.1981 → current

Long boring bits with morse taper shank, for boring through drill bushings

DIN 1866 edition 12.2007 → current

Countersink 90 °, with straight shank and fixed guide pin

DIN 1866 edition 6.1975 → replaced by edition 12.2007

Countersink 90 °, with straight shank and fixed guide pin

DIN 1867 Edition 12.2007 → current

Countersink 90 °, with Morse taper shank and exchangeable guide pin

DIN 1867 edition 6.1975 → replaced by edition 12.2007

Countersink 90 °, with Morse taper shank and exchangeable guide pin

DIN 1868 edition 8.1975 → current

Exchangeable guide pins for flat and countersinks

DIN 1869 · Edition 11.2006 → current

Extra-long twist drills with straight shank

DIN 1869 edition 3.1978 → replaced by edition 11.2006

Extra-long twist drills with straight shank

DIN 1870 edition 11.2006 → current

Extra-long twist drills with Morse taper shank

DIN 1870 edition 3.1978 → replaced by edition 11.2006

Extra-long twist drills with Morse taper shank

DIN 1871 edition 5.1999 → current

Gaseous fuels and other gases · Density and other volumetric quantities

DIN 1871 edition 5.1980 → replaced by edition 5.1999

Gaseous fuels and other gases · Density and relative density, based on the standard condition

DIN 1873 - Part 1 Edition 10.2016 → current

Motorized lawn mowers · Properties, requirements and tests · Hand-operated sickle mowers · Gasoline-powered, electrical mains or battery-operated

The standard describes walk-behind rotary mowers that do not have a device for the user to travel with and are intended for domestic use.

DIN 1873 edition 2.2004 → replaced by DIN 1873 part 1 edition 10.2016

Motorized lawn mowers · Hand-operated sickle mowers · Properties, requirements and tests

Correction of edition 10.2002

DIN 1873 edition 10.2002 → replaced by edition 2.2004

Motorized lawn mowers · Hand-operated sickle mowers · Properties, requirements and tests

DIN 1873 - Part 1 edition 12.1988 → replaced by DIN 1873 edition 10.2002

Motorized lawn mowers · Hand-operated sickle mowers · Properties, terms, requirements

DIN 1873 - Part 2 Edition 12.1988 → replaced by DIN 1873 Edition 10.2002

Lawn mower with motor · Hand-operated sickle mower · Properties of use, testing

DIN 1880 - Part 1 · Edition 11.1993 → current

Shell end mill with transverse groove and longitudinal groove · Dimensions

DIN 1880 - Part 1 · Edition 6.1981 → replaced by Edition 11.1993

Shell end mill with transverse groove · Dimensions

DIN 1880 - Part 2 Edition 9.2003 → current

Shell end mill with transverse groove and longitudinal groove · Technical delivery conditions

DIN 1880 - Part 2 · Edition 5.1995 → replaced by Edition 9.2003

Shell end mill with transverse groove and longitudinal groove · Technical delivery conditions

DIN 1880 - Part 2 · Edition 4.1990 → replaced by Edition 5.1995

Shell end mill with transverse groove · Technical delivery conditions

DIN 1880 - Part 2 · Edition 12.1981 → replaced by Edition 4.1990

Shell end mill with transverse groove · Technical delivery conditions

DIN 1880 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Shell end mill with transverse groove · Technical delivery conditions

DIN 1889 - Part 1 Edition 4.1989 → 6.2017 withdrawn without replacement

Die milling cutter, cylindrical with straight shank

DIN 1889 - Part 1 edition 12.1983 → replaced by edition 4.1989

Die milling cutter, cylindrical with straight shank

DIN 1889 - Part 1 · Edition 6.1957 → replaced by Edition 12.1983 and DIN 1889 Part 5 Edition 12.1983

Die cutter, cylindrical, with straight shank

DIN 1889 - Part 2 Edition 12.1983 → 6.2017 withdrawn without replacement

Die cutter, cylindrical with morse taper shank

DIN 1889 - Part 2 Edition 2.1957 → replaced by Edition 12.1983 and DIN 1889 Part 5 Edition 12.1983

Die cutter, cylindrical, with taper shank

DIN 1889 - Part 3 Edition 4.1989 → 6.2017 withdrawn without replacement

Die cutter, conical with straight shank

DIN 1889 - part 3 edition 12.1983 → replaced by edition 4.1989

Die cutter, conical with straight shank

DIN 1889 - part 3 edition 7.1957 → replaced by edition 12.1983 and DIN 1889 part 5 edition 12.1983

Die cutter, tapered, with straight shank

DIN 1889 - Part 5 Edition 4.1990 → 6.2017 withdrawn without replacement

Die milling cutters · Technical delivery conditions

DIN 1889 - Part 5 Edition 12.1983 → replaced by Edition 4.1990

Die milling cutters · Technical delivery conditions

DIN 1890 - Part 1 Edition 6.1981 → 6.2017 withdrawn without replacement

Grooving cutter · straight teeth, undercut · dimensions

DIN 1890 - Part 2 Edition 4.1990 → 6.2017 withdrawn without replacement

Slot milling cutter · straight-cut, relief-turned · technical delivery conditions

DIN 1890 - Part 2 edition 12.1981 → replaced by edition 4.1990

Slot milling cutter · straight-cut, relief-turned · technical delivery conditions

DIN 1890 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Slot milling cutter · straight-cut, relief-turned · technical delivery conditions

DIN 1891 - Part 1 Edition 6.1981 → 6.2017 withdrawn without replacement

Grooving cutter · coupled and adjustable · dimensions

DIN 1891 - Part 2 Edition 4.1990 → 6.2017 withdrawn without replacement

Slot milling cutter · coupled and adjustable · Technical delivery conditions

DIN 1891 - part 2 edition 12.1981 → replaced by edition 4.1990

Slot milling cutter · coupled and adjustable · Technical delivery conditions

DIN 1891 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Slot milling cutter · coupled and adjustable · Technical delivery conditions

DIN 1892 - Part 1 Edition 6.1981 → 6.2017 withdrawn without replacement

Milling cutter · coupled, two-part · Dimensions

DIN 1892 - Part 2 Edition 4.1990 → 6.2017 withdrawn without replacement

Milling cutter · coupled, two-part · Technical delivery conditions

DIN 1892 - part 2 edition 12.1981 → replaced by edition 4.1990

Milling cutter · coupled, two-part · Technical delivery conditions

DIN 1892 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Milling cutter · coupled, two-part · Technical delivery conditions

DIN 1893 - Part 1 Edition 9.1978 → 6.2017 withdrawn without replacement

Thread and disc milling cutters for ISO metric trapezoidal threads · Dimensions

DIN 1893 - Part 2 Edition 4.1990 → 6.2017 withdrawn without replacement

Thread and disc milling cutters for ISO metric trapezoidal threads · Technical delivery conditions

DIN 1893 - Part 2 · Edition 12.1981 → replaced by Edition 4.1990

Thread and disc milling cutters for ISO metric trapezoidal threads · Technical delivery conditions

DIN 1893 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Thread and disc milling cutters for ISO metric trapezoidal threads · Technical delivery conditions

DIN 1895 edition 5.2007 → current

Machine taper reamers for Morse taper

The standard specifies the dimensions for machine taper reamers of shapes C, D and E for reaming bores with Morse taper.

DIN 1895 edition 5.1975 → replaced by edition 5.2007

Machine taper reamers for Morse taper

DIN 1896 edition 5.1975 → withdrawn

Machine taper reamers for metric taper

DIN 1897 Edition 11.2006 → current

Extra short twist drill with straight shank

DIN 1897 edition 10.1984 → replaced by edition 11.2006

Extra short twist drill with straight shank

DIN 1897 edition 10.1961 → replaced by edition 10.1984

Extra short twist drill with straight shank

DIN 1898 - Part 1 · Edition 5.2007 → current

Pin hole drills for taper pin bores · Pin hole drills with straight shank

The standards specify the dimensions, designation, design and marking for pin hole drills with straight shank.

DIN 1898 - Part 1 · Edition 2.1990 → replaced by Edition 5.2007

Pin hole drill for taper pin bores with straight shank

DIN 1898 - Part 2 · Edition 5.2007 → current

Pin hole drill for taper pin holes · Pin hole drill with Morse taper shank

The standards specify the dimensions, designation, design and marking for pin hole drills with Morse taper shank.

DIN 1898 - Part 2 · Edition 2.1990 → replaced by Edition 5.2007

Pin hole drill for taper pin bores with Morse taper shank

DIN 1898 edition 10.1957 → replaced by DIN 1898 parts 1 and 2 edition 2.1990

Pin hole drill with taper 1: 50, for taper pins according to DIN 1 and DIN 7978

DIN 1899 edition 11.2006 → current

Micro drill

DIN 1899 edition 2.1990 → replaced by edition 11.2006

Micro drill

DIN 1899 edition 11.1973 → replaced by edition 2.1990

Micro drill; Twist drills, straight fluted drills, pointed drills

DIN 1900 · Edition 4.2010 → current

Requirement and qualification of soldering processes for metallic materials · Procedure qualification for arc soldering of steels

The standard applies to arc brazing on steels. It defines how an instruction for arc brazing is qualified by a process qualification and defines conditions for the execution of the process qualification and the scope of a qualified arc brazing process.

DIN 1910 - Part 1 Edition 7.1983 → replaced by DIN 1910 Part 100 Edition 2.2008 and DIN ISO 857 Part 1 Edition 11.2002

Welding · Terms, classification of welding processes

DIN 1910 - Part 1 · Edition 12.1974 → replaced by Edition 7.1983

Welding · Terms, classification of welding processes

DIN 1910 - Part 2 Edition 8.1977 → replaced by DIN 1910 Part 100 Edition 2.2008 and DIN ISO 857 Part 1 Edition 11.2002

Welding · Welding of metals, processes

DIN 1910 - Part 3 Edition 9.1977 → current

Welding · Welding of plastics, processes

DIN 1910 - Part 4 Edition 4.1991 → replaced by DIN 1910 Part 100 Edition 2.2008 and DIN ISO 857 Part 1 Edition 11.2002

Welding · gas shielded welding; Procedure

DIN 1910 - Part 4 Edition 8.1979 → replaced by Edition 4.1991

Welding · Inert gas welding, process

DIN 1910 - Part 5 Edition 12.1986 → replaced by DIN 1910 Part 100 Edition 2.2008 and DIN ISO 857 Part 1 Edition 11.2002

Welding · welding of metals · resistance welding; Procedure

DIN 1910 - Part 5 Edition 9.1980 → replaced by Edition 12.1986

Welding · Welding of metals · Resistance welding, processes

DIN 1910 - Part 10 Edition 7.1981 → replaced by DIN 1910 Part 100 Edition 2.2008 and DIN ISO 857 Part 1 Edition 11.2002

Welding · Mechanized arc welding processes · Terms

DIN 1910 - Part 11 Edition 2.1979 → current

Welding · Material-related terms for metal welding

DIN 1910 - Part 12 Edition 8.1989 → replaced by DIN 1910 Part 100 Edition 2.2008 and DIN ISO 857 Part 1 Edition 11.2002

Welding · Manufacturing-related terms for fusion welding of metals

DIN 1910 - Part 12 Edition 9.1980 → replaced by Edition 8.1989

Welding · Manufacturing-related terms for metal welding

DIN 1910 - Part 100 · Edition 2.2008 → current

Welding and related processes - terms · Metal welding processes with additions to DIN EN 14610: 2005

The standard defines basic welding terms as well as terms for welding work techniques.

DIN 1912 - Part 1 · Edition 6.1976 → replaced by DIN EN 12345 Edition 5.1999

Drawing, welding, soldering · Terms and names for welded joints, joints and seams

DIN 1912 - Part 2 Edition 9.1977 → replaced by DIN EN ISO 6947 Edition 5.1997

Graphic representation, welding, soldering · Working positions, seam inclination angle, seam rotation angle

DIN 1912 - Part 2 - Supplement 1 edition 12.1977 → replaced by DIN EN ISO 6947 edition 5.1997

Drawing, welding, soldering · Working positions, seam inclination angle, seam rotation angle · Determination of the working position on the pipe (examples)

DIN 1912 - Part 3 Edition 8.1982 → replaced by DIN 1912 Part 5 Edition 12.1987

Drawing, welding, soldering · Overlay welding

DIN 1912 - Part 4 · Edition 4.2017 → current

Drawings · Welding, soldering · Terms and names for soldered joints and soldered seams

DIN 1912 - Part 4 Edition 5.1981 → replaced by Edition 4.2017

Drawings · Welding, soldering · Terms and names for soldered joints and soldered seams

DIN 1912 - Part 5 Edition 12.1987 → replaced by DIN EN 22553 Edition 8.1994

Drawing welding, soldering · Symbols, dimensioning · ISO 2553, edition 1984 modified

DIN 1912 - Part 5 - Supplement 1 edition 12.1987 → replaced by DIN EN 22553 edition 8.1994

Graphic representation of welding, soldering · Symbols, dimensioning · Application examples for symbols for seam types according to ISO 2553

DIN 1912 - Part 5 Edition 2.1979 → replaced by Edition 12.1987

Drawing, welding, soldering · Principles for welded and soldered connections, symbols

DIN 1912 - Part 6 Edition 2.1979 → replaced by DIN 1912 Part 5 Edition 12.1987

Drawing, welding, soldering · Principles for dimensioning

DIN 1940 edition 12.1976 → current

Combustion engines · Reciprocating engines · Terms, symbols, units

DIN 1942 - Correction 1 · Edition 12.1996 → withdrawn

Acceptance tests on steam generators (VDI steam generator rules)

Corrections to edition 2.1994

DIN 1942 edition 2.1994 → withdrawn

Acceptance tests on steam generators (VDI steam generator rules)

DIN 1942 edition 6.1979 → replaced by edition 2.1994

Acceptance tests on steam generators (VDI steam generator rules)

DIN 1943 edition 2.1975 → current

Thermal acceptance tests on steam turbines (VDI steam turbine rules)

DIN 1944 edition 10.1968 → replaced by DIN EN ISO 9906 edition 8.2002

Acceptance tests on steam generators (VDI steam generator rules)

DIN 1945 - Part 1 · Edition 11.1980 → current

Positive displacement compressors · Thermodynamic acceptance and performance tests

DIN 1946 - Part 1 edition 10.1988 → replaced by DIN EN 12792 edition 1.2004

Ventilation technology Terminology and graphic symbols (VDI ventilation rules)

DIN 1946 - Part 1 · Edition 4.1960 → replaced by Edition 10.1988

Ventilation systems (VDI ventilation rules) · Basic rules

DIN 1946 - Part 2 Edition 1.1994 → replaced by DIN EN 13779 Edition 5.2005

Ventilation technology Health-related requirements (VDI ventilation rules)

DIN 1946 - Part 2 · Edition 1.1983 → replaced by Edition 1.1994

Ventilation technology Health-related requirements (VDI ventilation rules)

DIN 1946 - Part 3 Edition 7.2006 → current

Air conditioning · Air conditioning of cars and trucks

DIN 1946 - Part 3 · Edition 6.1962 → replaced by Edition 7.2006

Ventilation systems (VDI ventilation rules) · Ventilation of vehicles

DIN 1946 - Part 4 Edition 12.2008 → current

Ventilation technology · Ventilation systems in buildings and rooms in the healthcare sector

The standard applies to the planning, construction and acceptance of ventilation and air conditioning systems in buildings and rooms for the healthcare sector in which medical examinations and treatments are carried out on people, as well as for rooms directly connected to them.

DIN 1946 - part 4 edition 3.1999 → replaced by edition 12.2008

Ventilation technology · Ventilation systems in hospitals (VDI ventilation rules)

The standard contains technical and hygienic requirements for ventilation and air conditioning systems in hospitals.

DIN 1946 - part 4 edition 12.1989 → replaced by edition 3.1999

Ventilation technology · Ventilation systems in hospitals (VDI ventilation rules)

DIN 1946 - Part 4 edition 4.1978 → replaced by edition 12.1989

Ventilation systems (VDI ventilation rules) · Ventilation systems in hospitals

DIN 1946 - part 4 edition 5.1963 → replaced by edition 4.1978

Ventilation systems (VDI ventilation rules) · Ventilation in hospitals

DIN 1946 - Part 5 Edition 8.1967 → withdrawn

Ventilation systems (VDI ventilation rules) · Ventilation of schools

DIN 1946 - Part 6 · Edition 5.2009 → current

Ventilation technology · Ventilation of apartments - general requirements, requirements for dimensioning, execution and labeling, handover / acceptance (acceptance) and maintenance

The standard applies to both free and fan-assisted ventilation of apartments. Active cooling as well as active humidification and dehumidification of the air is not covered by this standard. The standard is a design and implementation standard that is primarily aimed at planners and those working on ventilation systems.

DIN 1946 - Part 6 Edition 10.1998 → replaced by Edition 5.2009

Ventilation technology · Ventilation of apartments · Requirements, execution, acceptance (VDI ventilation rules)

DIN 1946 - Part 6 Edition 9.1994 → replaced by Edition 10.1998

Ventilation technology · Ventilation of apartments · Requirements, execution, acceptance (VDI ventilation rules)

DIN 1946 - Part 6 - Supplement 1 · Edition 9.2012 → current

Ventilation technology · Ventilation of apartments - General requirements, requirements for dimensioning, execution and labeling, handover / acceptance (acceptance) and maintenance · Sample calculations for selected ventilation systems

Supplementary sheet 1 contains, in addition to DIN 1946 Part 6, exemplary calculations for the design of typical ventilation systems.

DIN 1946 - Part 6 - Supplement 2 · Edition 3.2013 → current

Ventilation technology · Ventilation of apartments - General requirements, requirements for dimensioning, execution and labeling, handover / acceptance (acceptance) and maintenance · Ventilation concept

Supplement 2 describes the determination of the necessary ventilation measures for a ventilation concept and the selection of a ventilation system with which the minimum air exchange required in the building regulations of the federal states or in the energy saving ordinance can be ensured.

DIN 1946 - Part 6 - Supplement 3 Edition 6.2017 → current

Ventilation systems · Ventilation of apartments - General requirements, requirements for dimensioning, execution and labeling, handover / acceptance (acceptance) and maintenance · Joint and non-joint operation of ventilation devices and single-room fireplaces for solid fuels - installation rules

DIN 1946 - Part 6 - Supplement 4 Edition 6.2017 → current

Ventilation technology · Ventilation of apartments - General requirements, requirements for dimensioning, execution and labeling, handover / acceptance (acceptance) and maintenance · Joint operation of ventilation devices and single-room fireplaces for solid fuels - Installation examples

DIN 1946 - Part 7 Edition 7.2009 → current

Ventilation technology · Ventilation systems in laboratories

DIN 1946 - Part 7 · Edition 6.1992 → replaced by Edition 7.2009

Ventilation technology · Ventilation systems in laboratories (VDI ventilation rules)

DIN 1952 edition 7.1982 → replaced by DIN EN ISO 5167 part 1 edition 11.1995

Flow measurement with orifices, nozzles and Venturi tubes in fully flowed tubes with circular cross-section (VDI flow measurement rules)

DIN 1952 edition 8.1971 → replaced by edition 7.1982

VDI flow measurement rules · Rules for flow measurement with standardized nozzles, orifices and Venturi nozzles

DIN 1960 edition 9.2016 → current

VOB procurement and contract regulations for construction works · Part A: General provisions for the procurement of construction works

DIN 1960 edition 9.2012 → replaced by edition 9.2016

VOB procurement and contract regulations for construction works · Part A: General provisions for the procurement of construction works

DIN 1960 edition 8.2010 → replaced by edition 9.2012

VOB procurement and contract regulations for construction works · Part A: General provisions for the procurement of construction works

Correction of edition 4.2010

DIN 1960 edition 4.2010 → replaced by edition 8.2010

VOB procurement and contract regulations for construction works · Part A: General provisions for the procurement of construction works

DIN 1960 edition 5.2006 → replaced by edition 4.2010

VOB procurement and contract regulations for construction works · Part A: General provisions for the procurement of construction works

DIN 1960 edition 12.2002 → replaced by edition 5.2006

VOB procurement and contract regulations for construction works · Part A: General provisions for the procurement of construction works

DIN 1960 edition 12.2000 → replaced by edition 12.2002

VOB contracting regulations for construction works · Part A: General provisions for the award of construction works

DIN 1960 edition 12.1992 → replaced by edition 12.2000

VOB contracting regulations for construction works · Part A: General provisions for the award of construction works

DIN 1960 edition 7.1990 → replaced by edition 12.1992

VOB contracting regulations for construction works · Part A: General provisions for the award of construction works

DIN 1960 edition 9.1988 → replaced by edition 7.1990

VOB contracting regulations for construction works · Part A: General provisions for the award of construction works

DIN 1960 edition 10.1979 → replaced by edition 9.1988

VOB contracting regulations for construction works · Part A: General provisions for the award of construction works

DIN 1961 edition 9.2016 → current

VOB procurement and contract regulations for construction work · Part B: General contractual conditions for the execution of construction work

The standard defines the general contractual conditions for the execution of construction works.

DIN 1961 edition 9.2012 → replaced by edition 9.2016

VOB procurement and contract regulations for construction work · Part B: General contractual conditions for the execution of construction work

The standard defines the general contractual conditions for the execution of construction works.

DIN 1961 edition 8.2010 → replaced by edition 9.2012

VOB procurement and contract regulations for construction work · Part B: General contractual conditions for the execution of construction work

Correction of edition 4.2010

DIN 1961 edition 4.2010 → replaced by edition 8.2010

VOB procurement and contract regulations for construction work · Part B: General contractual conditions for the execution of construction work

DIN 1961 edition 10.2006 → replaced by edition 4.2010

VOB procurement and contract regulations for construction work · Part B: General contractual conditions for the execution of construction work

DIN 1961 edition 12.2002 → replaced by edition 10.2006

VOB procurement and contract regulations for construction work · Part B: General contractual conditions for the execution of construction work

DIN 1961 edition 12.2000 → replaced by edition 12.2002