List of standards DIN 3000 to DIN 3499

Logo of the German Institute for Standardization

The list of standards DIN 3000 to DIN 3499 lists all current standards and many historical standard editions in the number range 3000 to 3499.

DIN - German Institute for Standardization e. V. - is the national standardization organization of the Federal Republic of Germany based in Berlin .

Explanations of the list

• DIN-EN standards, DIN-EN-ISO standards, DIN-ISO standards, preliminary standards and draft standards are not listed in this list.
• The term “sheet” used in older standard editions has been uniformly transferred to “part”.
• The date of issue is indicated next to the standard number. Edition 9.1981 means that the standard was published in September 1981.
• Cross edition: If the date of issue is appended with an x, for example edition 9.1949x, the standard has only been changed slightly and remains valid.
• Unless otherwise noted, the withdrawal date of an old standard is the same as the issue date of the replacing standard (s).
• The entry "→ current" means that the standard is currently (as of June 2017) valid.

DIN 3001 edition 2.1932 → withdrawn

Strip steel rulers with bevelled edge

DIN 3002 edition 2.1932 → withdrawn

Steel strip triangles, equal angles, acute angles

DIN 3003 edition 12.1932 → withdrawn

Wooden leveling staffs with single division

DIN 3004 edition 12.1932 → withdrawn

Wooden leveling staffs with chess board graduation

DIN 3005 edition 12.1932 → withdrawn

Ranging poles made of wood

DIN 3006 edition 12.1932 → withdrawn

Wooden rulers

DIN 3007 edition 12.1932 → withdrawn

Measuring tapes (land measuring tapes) and straightening rods

DIN 3008 edition 12.1932 → withdrawn

Height bolts

DIN 3009 edition 11.1933 → withdrawn

Test meter sticks with blade-shaped ends

DIN 3010 edition 11.1933 → withdrawn

Measuring rods with graduations

DIN 3011 edition 11.1933 → withdrawn

Measuring wedge

DIN 3012 edition 11.1933 → withdrawn

Slatted base

DIN 3013 edition 11.1933 → withdrawn

Staff judge

DIN 3014 - Part 1 Edition 8.1934 → withdrawn

Tape measure

DIN 3014 - Part 2 Edition 8.1934 → withdrawn

Tape measure

DIN 3015 - Part 1 · Edition 1.1999 → current

Mounting clamps Block-shaped clamps Light series (L)

DIN 3015 - Part 1 edition 7.1997 → replaced by edition 1.1999

Mounting clamps Block-shaped clamps Light series (L)

DIN 3015 - Part 1 · Edition 2.1992 → replaced by Edition 7.1997

Mounting clamps Block-shaped clamps Light series (L)

DIN 3015 - Part 2 Edition 1.1999 → current

Mounting clamps Block-shaped clamps Heavy series (S)

DIN 3015 - Part 2 Edition 7.1997 → replaced by Edition 1.1999

Mounting clamps Block-shaped clamps Heavy series (S)

DIN 3015 - Part 2 · Edition 2.1992 → replaced by Edition 7.1997

Mounting clamps Block-shaped clamps Heavy series (S)

DIN 3015 - Part 3 · Edition 1.1999 → current

Mounting clamps · clamps in block form · double clamps

DIN 3015 - Part 3 · Edition 6.1997 → replaced by Edition 1.1999

Mounting clamps · clamps in block form · double clamps

DIN 3015 - Part 3 · Edition 2.1992 → replaced by Edition 6.1997

Bracket clamps Block-shaped clamps Double clamps (Z)

DIN 3015 - Part 10 Edition 2.1994 → current

Mounting clamps · Clamps in block form · Technical delivery conditions

DIN 3016 - Part 1 · Edition 6.2000 → current

Mounting clamps · With lugs

DIN 3016 - Part 1 · Edition 4.1988 → replaced by Edition 6.2000

Mounting clamps with tabs

DIN 3016 - Part 2 · Edition 6.2000 → current

Mounting clamps · With clamping jaws

DIN 3016 - Part 2 · Edition 4.1988 → replaced by Edition 6.2000

Retaining clamps with clamping jaws

DIN 3016 - Part 3 · Edition 6.2000 → current

Mounting clamps · Profile clamps and conical flanges

DIN 3016 - Part 3 Edition 11.1992 → replaced by Edition 6.2000

Mounting clamps · Profile clamps and conical flanges

DIN 3016 - Part 4 Edition 10.2000 → current

Mounting clamps · Technical delivery conditions

Correction of edition 6.2000

DIN 3016 - Part 4 Edition 6.2000 → replaced by Edition 10.2000

Mounting clamps · Technical delivery conditions

DIN 3016 - Part 4 Edition 12.1993 → replaced by Edition 6.2000

Mounting clamps with lugs and clamping jaws · Technical delivery conditions

DIN 3017 - Part 1 · Edition 5.1998 → current

Hose clamps · clamps with worm drive; Form A

DIN 3017 - Part 1 · Edition 3.1998 → replaced by Edition 5.1998

Hose clamps · clamps with worm drive; Form A

DIN 3017 - Part 1 · Edition 4.1987 → replaced by Edition 3.1998

Hose clamps with worm drive; Form A

DIN 3017 - Part 1 · Edition 7.1980 → replaced by Edition 4.1987

Hose clamps with worm drive

DIN 3017 - Part 2 · Edition 6.2002 → current

Hose clamps · Clamps with clamping jaws

DIN 3017 - Part 2 edition 11.1983 → replaced by edition 6.2002

Hose clamps · Clamps with clamping jaws

DIN 3017 - Part 3 · Edition 10.2002 → current

Hose clamps · Clamps with round bolts

Correction of edition 6.2000

DIN 3017 - Part 3 · Edition 6.2002 → replaced by Edition 10.2002

Hose clamps · Clamps with round bolts

DIN 3017 - Part 3 · Edition 6.1984 → replaced by Edition 6.2002

Hose clamps with round bolts

DIN 3017 - Part 4 Edition 5.1998 → current

Hose clamps · Technical delivery conditions

DIN 3017 - Part 4 Edition 3.1998 → replaced by Edition 5.1998

Hose clamps · Technical delivery conditions

DIN 3017 - Part 4 Edition 7.1989 → replaced by Edition 3.1998

Hose clamps · Technical delivery conditions

DIN 3017 - Part 5 · Edition 6.2002 → current

Hose clamps · wide band clamps with clamping jaws; Forms D and E

DIN 3017 - Part 5 · Edition 1.1988 → replaced by Edition 6.2002

Hose clamps · wide band clamps with clamping jaws; Forms D and E

DIN 3017 edition 1.1972 → withdrawn

Hose clamps · with worm drive

DIN 3018 · Edition 5.1984 → withdrawn

Oil level indicator

DIN 3018 edition 2.1972 → replaced by edition 5.1984

Oil level indicator

DIN 3019 · Edition 4.1972 → current

Industrial trucks · Trapezoidal block springs for running axles of handcarts and trailers

DIN 3020 · Edition 6.1934 → withdrawn

Signs for survey plans

DIN 3021 - Part 1 Edition 11.2016 → current

Hose clamps - spring band clamps (FBS) · Dimensions, designation, materials, design

DIN 3021 - part 1 edition 6.1999 → replaced by edition 11.2016

Hose clamps - spring band clamps (FBS) · Dimensions, designation, materials, design

DIN 3021 - Part 2 Edition 11.2016 → current

Hose clamps - spring band clamps (FBS) · Technical delivery conditions

DIN 3021 - Part 2 Edition 6.1999 → replaced by Edition 11.2016

Hose clamps - spring band clamps (FBS) · Technical delivery conditions

DIN 3021 - Part 3 Edition 11.2016 → current

Hose clamps - spring band clamps (FBS) · System: spring band clamp-hose connector

DIN 3021 - Part 3 Edition 6.1999 → replaced by Edition 11.2016

Hose clamps - spring band clamps (FBS) · System: spring band clamp-hose connector

DIN 3025 · Edition 6.1933 → withdrawn

Signs for geodetic terms and sizes

DIN 3036 - part 1 edition 3.1978 → replaced by DIN EN 10218 part 2 edition 8.1996

Plastic-coated steel wires · In the extruder process, plastic-coated steel wires (plastic-coated), dimensions and permissible deviations

DIN 3036 - Part 2 Edition 3.1978 → replaced by DIN EN 10218 Part 2 Edition 8.1996

Plastic-coated steel wires · In the fluidized bed process, plastic-coated steel wires (plastic-coated), dimensions and permissible deviations

DIN 3051 - part 1 edition 3.1972 → replaced by DIN EN 12385 part 2 edition 4.2003

Steel wire ropes · Basics, overview

DIN 3051 - part 2 edition 4.1972 → replaced by DIN EN 12385 part 2 edition 4.2003

Steel wire ropes · Basics, types of ropes, terms

DIN 3051 - Part 3 Edition 3.1972 → replaced by DIN EN 12385 Part 2 Edition 4.2003

Steel wire ropes · Basics, calculation, factors

DIN 3051 - part 4 edition 3.1972 → replaced by DIN EN 12385 part 1 edition 3.2003 and DIN EN 12385 part 2 edition 4.2003

Steel wire ropes · Basics, technical delivery conditions

DIN 3052 edition 3.1972 → withdrawn

Wire ropes made of steel wires · spiral rope 1 × 7

The application of DIN EN 12385 Part 10 Edition 7.2008 is recommended.

DIN 3053 edition 3.1972 → withdrawn

Wire ropes made of steel wires · spiral rope 1 × 19

The application of DIN EN 12385 Part 10 Edition 7.2008 is recommended.

DIN 3054 edition 3.1972 → withdrawn

Wire ropes made of steel wires · spiral rope 1 × 37

The application of DIN EN 12385 Part 10 Edition 7.2008 is recommended.

DIN 3055 edition 3.1972 → replaced by DIN EN 12385 part 4 edition 3.2003

Wire ropes made of steel wires · round strand rope 6 × 7

DIN 3056 edition 3.1972 → replaced by DIN EN 12385 part 4 edition 3.2003

Steel wire ropes 8 × 7 round strand rope

DIN 3057 edition 3.1972 → withdrawn

Steel wire ropes · Round strand rope 6 × 19 filler

DIN 3058 edition 3.1972 → replaced by DIN EN 12385 part 4 edition 3.2003

Steel wire ropes · Round strand rope 6 × 19 Seale

DIN 3059 Edition 3.1972 → replaced by DIN EN 12385 Part 4 Edition 3.2003

Steel wire ropes · 6 × 19 Warrington round strand rope

DIN 3060 edition 3.1972 → replaced by DIN EN 12385 part 4 edition 3.2003

Steel wire ropes · Round strand rope 6 × 19 standard

DIN 3061 edition 3.1972 → replaced by DIN EN 12385 part 4 edition 3.2003

Wire ropes made of steel wires · round strand rope 8 × 19 filler

DIN 3062 edition 9.1973 → replaced by DIN EN 12385 part 4 edition 3.2003

Wire ropes made of steel wires · Round strand rope 8 × 19 Seale

DIN 3063 edition 9.1973 → replaced by DIN EN 12385 part 4 edition 3.2003

Steel wire ropes · 8 × 19 Warrington round strand rope

DIN 3064 edition 3.1972 → replaced by DIN EN 12385 part 4 edition 3.2003

Steel wire ropes · round strand rope 6 × 36 Warrington-Seale

DIN 3065 Edition 3.1972 → replaced by DIN EN 12385 Part 4 Edition 3.2003

Steel wire ropes · 6 × 35 Warrington covered round strand rope

DIN 3066 edition 3.1972 → replaced by DIN EN 12385 part 4 edition 3.2003

Steel wire ropes · Round strand rope 6 × 37 standard

DIN 3067 Edition 3.1972 → replaced by DIN EN 12385 Part 4 Edition 3.2003

Steel wire ropes · Round strand rope 8 × 36 Warrington-Seale

DIN 3068 · Edition 3.1972 → current

Steel wire ropes · Round strand rope 6 × 24 standard + 7 fiber cores

DIN 3069 edition 3.1972 → replaced by DIN EN 12385 part 4 edition 3.2003

Steel wire ropes · Spiral round strand rope 18 × 7, rotation-resistant

DIN 3070 edition 3.1972 → withdrawn

Steel wire ropes · flat strand rope 10 × 10, rotation-resistant

DIN 3071 Edition 7.1972 → replaced by DIN EN 12385 Part 4 Edition 3.2003

Steel wire ropes · Spiral round strand rope 36 × 7, rotation-free

DIN 3078 edition 5.1990 → replaced by DIN EN 10264 part 1 edition 6.2002 and DIN EN 10264 part 3 edition 2.2003

Steel wires for hoisting ropes

DIN 3078 edition 5.1982 → replaced by edition 5.1990

Steel wires for hoisting ropes and stage ropes · Round wires

DIN 3088 · edition 5.1989 → replaced by DIN EN 13414 part 1 edition 11.2003, DIN EN 13414 part 2 edition 12.2003 and DIN EN 13414 part 3 edition 7.2004

Wire ropes made of steel wires · Sling ropes in hoist operation · Safety requirements and testing

DIN 3088 · Edition 5.1976 → replaced by Edition 5.1989

Sling ropes for fastening loads to load hooks

DIN 3089 - Part 1 edition 5.1990 → replaced by DIN EN 13411 Part 2 edition 4.2002

Steel wire ropes · Splices · Splice end connections on wire ropes

DIN 3089 - Part 1 · Edition 4.1984 → replaced by Edition 5.1990

Steel wire ropes · Splices · Splice end connections on wire ropes

DIN 3089 - Part 2 · Edition 4.1984 → current

Steel wire ropes · Splices · Long splice

DIN 3090 edition 8.1989 → replaced by VG 85275 edition 5.2012 and DIN EN 13411 part 1 edition 5.2002

Thimbles - shaped steel thimbles for wire ropes

DIN 3090 edition 7.1977 → replaced by edition 8.1989

Thimbles - shaped steel thimbles for wire ropes

DIN 3091 edition 12.1988 → current

Thimbles · Full thimbles for wire ropes

DIN 3091 edition 11.1976 → replaced by edition 12.1988

Thimbles · Full thimbles for wire ropes

DIN 3092 - Part 1 Edition 5.1985 → replaced by DIN EN 13411 Part 4 Edition 5.2002

Wire rope potting in rope sockets · Metallic potting · Safety requirements and testing

DIN 3092 edition 11.1979 → replaced by DIN 3092 part 1 edition 5.1985

Metallic wire rope potting in rope sockets · Safety requirements and testing

DIN 3093 - part 1 edition 12.1988 → replaced by DIN EN 13411 part 3 edition 9.2004

Ferrules made of wrought aluminum alloys · Blanks made from flat oval tubes with constant wall thickness · Technical delivery conditions

DIN 3093 - Part 1 edition 8.1976 → replaced by edition 12.1988

Ferrules made of wrought aluminum alloys · Blanks made from flat oval tubes with constant wall thickness · Technical delivery conditions

DIN 3093 - part 2 edition 12.1988 → replaced by DIN EN 13411 part 3 edition 9.2004

Press clamps made of wrought aluminum alloys · Press connections · Safety requirements

DIN 3093 - Part 2 edition 8.1976 → replaced by edition 12.1988

Press clamps made of wrought aluminum alloys · Press connections made of blanks with constant wall thickness · Shapes, assignment

DIN 3093 - part 3 edition 8.1976 → replaced by DIN 3093 part 2 edition 12.1988

Press clamps made of wrought aluminum alloys Press connections made of blanks with constant wall thickness Production, quality requirements, testing

DIN 3094 edition 1.1978 → current

Round reel for wire ropes

DIN 3095 - part 1 edition 12.1988 → replaced by DIN EN 13411 part 3 edition 9.2004

Flemish eyes with steel ferrules · Steel ferrules, safety requirements, testing

DIN 3095 - Part 2 Edition 12.1988 → replaced by DIN EN 13411 Part 3 Edition 9.2004

Flemish eyes with steel ferrules · Shapes, safety requirements, testing

DIN 3095 edition 1.1984 → replaced by DIN 3095 parts 1 and 2 editions 12.1988

Flemish eyes with steel ferrules · Steel ferrules, safety requirements, testing

DIN 3100 edition 4.1987 → withdrawn

Drawing boards · Dimensions, requirements, testing

DIN 3100 · Edition 6.1962 → replaced by Edition 4.1987

Drawing boards (drawing boards)

DIN 3101 edition 4.1987 → withdrawn

Sign rails

DIN 3101 edition 6.1962 → replaced by edition 4.1987

Sign rails (tear rails)

DIN 3102 edition 4.1987 → replaced by DIN ISO 9960 part 3 edition 8.1995

Drawing triangles

DIN 3102 · Edition 6.1962 → replaced by Edition 4.1987

Drawing triangles

DIN 3110 edition 9.2007 → current

Open-end wrench · Test torques according to row C

The standard deals with double open-end wrenches with unequal widths across flats, which are used to operate screw connections.

DIN 3110 edition 1.1987 → replaced by edition 9.2007

Double open-end wrenches with unequal wrench sizes · Test torques according to series C

DIN 3110 edition 4.1976 → replaced by edition 1.1987

Double open-end wrenches with unequal wrench sizes · Test torques according to series C

DIN 3110 edition 11.1966 → withdrawn

Double open-end wrenches with unequal wrench sizes and test torques according to row C

DIN 3110 edition 10.1961 → withdrawn

Double open-end wrenches with unequal wrench sizes and test torques according to row C

DIN 3111 edition 9.2007 → current

Single ring wrench · Test torques according to row A

The standard deals with single ring spanners that are used to operate hexagon and double hexagon screw connections.

DIN 3111 edition 11.1982 → replaced by edition 9.2007

Single ring wrench · Test torques according to row A

DIN 3111 edition 11.1964 → withdrawn

Single ring spanner with test torques according to row A

DIN 3111 · Edition 5.1951 → withdrawn

Single ring spanner

DIN 3112 edition 9.2007 → current

Socket wrench, solid and made of tube · Test torques according to row A

The standard deals with socket wrenches that are mainly used for deep screw connections and the resulting higher torque loads.

DIN 3112 edition 11.1982 → replaced by edition 9.2007

Socket wrench, solid

DIN 3112 edition 8.1967 → withdrawn

Solid socket wrench

DIN 3112 · Edition 6.1946 → withdrawn

Hexagon socket wrench, forged, long version

DIN 3113 edition 9.2007 → current

Combination spanners with the same width across flats · Test torques according to series A and C

The standard deals with combination wrenches with the same width across flats that are used to operate screw connections.

DIN 3113 edition 11.1984 → replaced by edition 9.2007

Combination spanners with the same width across flats · Test torques according to series A and C

DIN 3114 edition 9.2007 → current

Open-ended spanners · Test torques according to row C

The standard deals with single-open-ended spanners that are used to operate screw connections.

DIN 3114 edition 8.1979 → replaced by edition 9.2007

Open-ended spanners · Test torques according to row C

DIN 3115 - Part 1 Edition 8.1978 → withdrawn

Slotted nut driver with handle

DIN 3115 - Part 1 Edition 11.1967 → withdrawn

Slotted nut driver with handle

DIN 3115 - Part 2 Edition 8.1978 → withdrawn

Slotted nut driver with flat shank

DIN 3115 - Part 2 Edition 11.1967 → withdrawn

Slotted nut driver with flat shank

DIN 3116 Edition 8.1978 → current

Two-hole nut driver

DIN 3116 edition 11.1967 → withdrawn

Two-hole nut driver

DIN 3117 · Edition 5.1988 → withdrawn

Adjustable open-end wrenches

DIN 3117 edition 8.1978 → replaced by edition 5.1988

Adjustable open-end wrenches

DIN 3117 edition 1.1968 → withdrawn

Adjustable open-end wrenches

DIN 3118 edition 9.2007 → current

Open double ring spanners · Test torques according to series C

The standard deals with open double ring spanners that are used to operate union screws and union nuts for pipe fittings.

DIN 3118 edition 5.1988 → replaced by edition 9.2007

Open double ring spanners with unequal widths across flats · Test torques according to series C

DIN 3119 · Edition 4.2017 → current

Cross socket wrench · Test torques according to row A

DIN 3119 edition 1.1982 → replaced by edition 4.2017

Cross socket wrench · Test torques according to row A

DIN 3120 · Edition 12.1993 → current

Connecting square for hand-operated screwing tools

DIN 3120 edition 12.1986 → replaced by edition 12.1993

Connecting square for hand-operated screwing tools

DIN 3120 edition 4.1976 → replaced by edition 12.1986

Connecting square for hand-operated screwing tools

DIN 3120 edition 3.1971 → withdrawn

Connecting square for hand-operated screwing tools

DIN 3120 · Edition 2.1963 → withdrawn

Connecting square for hand-operated sockets

DIN 3121 edition 12.1993 → current

Connecting square for machine-operated screwing tools

DIN 3121 edition 1.1987 → replaced by edition 12.1993

Connecting square for power screwdriver tools

DIN 3121 edition 4.1976 → replaced by edition 1.1987

Connecting square for power screwdriver tools

DIN 3121 edition 3.1971 → withdrawn

Connecting square for power screwdriver tools

DIN 3122 · Edition 4.2017 → current

Drive parts with external square for hand-operated socket wrench inserts

The standard applies to drive parts with external square for manual operation of socket wrench inserts with internal square according to DIN 3120. The standard partly corresponds to the international standard ISO 3315, edition 4.2011.

DIN 3122 edition 3.1989 → replaced by edition 4.2017

Drive parts with external square for hand-operated socket wrench inserts

DIN 3122 edition 8.1976 → replaced by edition 3.1989

Drive parts with external square for hand-operated socket wrench inserts

DIN 3122 · Edition 5.1968 → withdrawn

Drive parts for hand-operated sockets with internal square drive

DIN 3123 · Edition 4.2017 → current

Connecting parts with external square for hand-operated sockets

The standard applies to connecting parts with external square for manual operation of socket wrench inserts with internal square according to DIN 3120. The standard partly corresponds to the international standard ISO 3316, edition 3.2012.

DIN 3123 · Edition 3.1989 → replaced by Edition 4.2017

Connecting parts with external square for hand-operated sockets

DIN 3123 edition 4.1976 → replaced by edition 3.1989

Connecting parts with external square for hand-operated sockets

DIN 3123 · Edition 4.1968 → withdrawn

Connecting parts for hand-operated screwdriving tools with internal square drive

DIN 3124 Edition 11.2007 → current

Socket wrench inserts with internal square for screws with hexagon, hand-operated

The socket wrench inserts described in the standard with internal square, for example for cross handles, cranks, ratchets, plug-in handles, all with external square, are used to operate hexagon screws and nuts by hand.

DIN 3124 edition 11.1980 → replaced by edition 11.2007

Socket wrench inserts with internal square for screws with hexagon, hand-operated

DIN 3124 · Edition 4.1968 → withdrawn

Hand socket wrench inserts with internal square drive

DIN 3125 edition 1.2008 → current

Socket wrench with handle · Dimensions and test torques

Correction of edition 9.2007

DIN 3125 edition 9.2007 → replaced by edition 1.2008

Socket wrench with handle · Dimensions and test torques

The standard describes socket wrenches with a handle, which are mainly used for the manual operation of screw connections that are structurally lower or unfavorable and that only require a low torque for operation without a lever arm.

DIN 3125 edition 12.2000 → replaced by edition 9.2007

Socket wrench with handle

DIN 3125 edition 9.1979 → replaced by edition 12.2000

Socket wrench with handle

DIN 3126 edition 1.2004 → replaced by DIN ISO 1173 edition 6.2009

Driver connections for screwdriver bits and connecting parts · Dimensions

DIN 3126 edition 12.1993 → replaced by edition 1.2004

Driver connections for screwdriver bits and connecting parts · Dimensions

DIN 3126 edition 12.1986 → replaced by edition 12.1993

Driver connections for screwdriver bits and connecting parts · Dimensions

DIN 3126 edition 4.1976 → replaced by edition 12.1986

Connection hexagon for power screwdriver tools

DIN 3126 edition 3.1971 → withdrawn

Connection hexagon for power screwdriver tools

DIN 3127 - Part 1 edition 5.1995 → replaced by DIN ISO 2351 Part 1 edition 4.2007

Screwdriver bits for slotted screws · Dimensions

DIN 3127 - Part 1 · Edition 3.1987 → replaced by Edition 5.1995

Screwdriver bits for slotted screws · Dimensions

DIN 3127 - Part 1 · Edition 4.1976 → replaced by Edition 3.1987

Screwdriver bits with external hexagon for slotted screws · Dimensions and quality specifications

DIN 3127 - Part 1 · Edition 2.1969 → withdrawn

Screwdriver bits with external hexagon for slotted screws · Dimensions and quality specifications

DIN 3127 - Part 2 · Edition 1.1971 → withdrawn

Screwdriver bits with external hexagon for slotted screws · Guide sleeves

DIN 3128 edition 1.1994 → replaced by DIN ISO 2351 part 2 edition 1.2006

Screwdriver bits for screws with cross recess · Dimensions

DIN 3128 edition 3.1987 → replaced by edition 1.1994

Screwdriver bits for Phillips screws · Dimensions

DIN 3128 · Edition 5.1969 → replaced by Edition 3.1987

Screwdriver bits with external hexagon for cross-head screws

DIN 3129 · Edition 3.2012 → current

Screwdriving tools · Socket wrench inserts with internal square for hexagon screws, machine-operated and accessories · Dimensions, design and test torques

The standard specifies requirements for machine-operated sockets with wrench sizes between 3.2 mm and 115 mm, with an internal square for hexagon screws.

DIN 3129 edition 2.1987 → replaced by edition 3.2012

Socket wrench inserts with internal square for hexagon screws, machine-operated

DIN 3129 edition 11.1982 → replaced by edition 2.1987

Socket wrench inserts with internal square for hexagon screws, machine-operated

DIN 3129 · Edition 5.1972 → withdrawn

Machine socket wrench inserts with internal square

DIN 3131 edition 7.1944 → withdrawn

Box handles

DIN 3132 Edition 7.1984 → current

Latches · sealable, with short contact surface

DIN 3132 edition 2.1961 → replaced by edition 7.1984

Latches · surface-mounted, sealable, with short support plate

DIN 3133 Edition 7.1984 → current

Latches · sealable, with long contact surface

DIN 3133 edition 2.1961 → replaced by edition 7.1984

Latches · surface-mounted, sealable, with long support plate

DIN 3134 Edition 7.1984 → current

Latches with and without locking eyes

DIN 3134 · Edition 7.1962 → replaced by Edition 7.1984

Latches on top, without and with staple (for padlock)

DIN 3135 · Edition 5.1983 → current

Box handles · enclosed

DIN 3135 edition 1.1961 → replaced by edition 5.1983

Box handles · Recessed handle, with rectangular support plate

DIN 3136 · Edition 5.1983 → current

Box handles · overlying

DIN 3136 edition 1.1961 → replaced by edition 5.1983

Box handles · surface-mounted, with rounded support plate

DIN 3140 - part 1 edition 10.1978 → replaced by DIN ISO 10110 part 1 edition 2.2000

Dimensions and tolerances for individual optical parts · Representation, dimensions, material

DIN 3140 - Part 1 Issue 3.1971 → withdrawn

Optical components · Drawing information, representation, dimensions, material

DIN 3140 - Part 2 Edition 10.1978 → replaced by DIN ISO 10110 Part 3 Edition 2.2000

Dimensions and tolerances for individual optical parts · Bubbles

DIN 3140 - Part 2 · Edition 12.1968 → withdrawn

Optical items · bubbles

DIN 3140 - Part 3 Edition 10.1978 → replaced by DIN ISO 10110 Part 4 Edition 2.2000

Dimensions and tolerances for individual optical parts · Schlieren

DIN 3140 - part 4 edition 10.1978 → replaced by DIN ISO 10110 part 2 edition 2.2000

Dimensions and tolerances for individual optical components · Tensions

DIN 3140 - Part 4 Edition 2.1970 → withdrawn

Optical components · Tensions

DIN 3140 - Part 5 Edition 10.1978 → replaced by DIN ISO 10110 Part 5 Edition 2.2000

Dimensions and tolerances for individual optical parts · Fitting errors

DIN 3140 - Part 5 · Edition 6.1969 → withdrawn

Optical components · Incorrect fit

DIN 3140 - Part 6 Edition 10.1978 → replaced by DIN ISO 10110 Part 6 Edition 2.2000

Dimensions and tolerances for individual optical parts · Centering errors

DIN 3140 - Part 6 Edition 9.1972 → withdrawn

Optical components · Centering errors

DIN 3140 - Part 7 Edition 10.1978 → replaced by DIN ISO 10110 Part 7 Edition 2.2000

Dimensions and tolerances for individual optical parts · Surface defects

DIN 3140 - Part 7 Issue 3.1969 → withdrawn

Optical components · Surface defects

DIN 3140 - Part 8 Edition 10.1978 → replaced by DIN ISO 10110 Part 8 Edition 2.2000

Dimensions and tolerances for individual optical components · Surface quality

DIN 3140 - Part 8 · Edition 6.1973 → withdrawn

Optical components · Surface quality

DIN 3140 - Part 9 Edition 4.1978 → replaced by DIN ISO 10110 Part 9 Edition 2.2000

Dimensions and tolerances for individual optical parts · Surface coatings

DIN 3140 - Part 10 Edition 5.1978 → replaced by DIN ISO 10110 Part 7 Edition 2.2000

Dimensions and tolerances for individual optical parts · Defects in surface coatings

DIN 3140 - supplement 1 edition 5.1978 → replaced by DIN ISO 10110 supplement 1 and 2 edition 2.2000

Drawing information for individual optical parts · Drawing examples, index

DIN 3140 edition 10.1958 → withdrawn

Optical parts, drawing details · Representation, materials, surfaces

DIN 3142 edition 3.1960 → withdrawn

Identification of surfaces in drawings using roughness measurements

DIN 3151 edition 11.1935 → withdrawn

Seamless Mild Steel Tubing · Choice for the Refrigeration Industry

DIN 3154 edition 11.1935x → withdrawn

Flanges for brine lines for ND 10

Cross edition 10.1948

DIN 3156 edition 11.1935x → withdrawn

Flanges for ammonia lines for ND 25

Cross edition 1.1949

DIN 3158 edition 12.1987 → replaced by DIN EN 12284 edition 1.2004

Refrigerant fittings · Safety specifications · Testing, labeling

DIN 3158 - part 1 edition 3.1974 → replaced by DIN 3158 edition 12.1987

Valves for refrigerant circuits · Application, materials

DIN 3158 - Part 2 · Edition 3.1974 → replaced by DIN 3158 Edition 12.1987

Valves for refrigerant circuits · Technical delivery conditions

DIN 3159 · Edition 5.1965 → current

Flange connections for refrigerant fittings up to ND 25

DIN 3160 edition 8.1974 → current

Straight shut-off valves for refrigerant circuits Nominal pressure 25

DIN 3160 · Edition 10.1960 → withdrawn

Straight-way valves for refrigerants · for nominal pressure 25 · dimensions, technical delivery conditions

DIN 3160 · Edition 6.1938 → withdrawn

Straight-through valves for ammonia lines for ND 25

DIN 3161 edition 8.1974 → current

Angle shut-off valves for refrigerant circuits Nominal pressure 25

DIN 3161 edition 10.1960 → withdrawn

Angle valves for refrigerants · for nominal pressure 25 · dimensions, technical delivery conditions

DIN 3161 · Edition 6.1938 → withdrawn

Angle valves for ammonia lines for ND 25

DIN 3162 edition 8.1974 → current

Protective caps for valves in refrigerant circuits Nominal pressure 25

DIN 3163 Edition 8.1974 → current

Straight control valves for refrigerant circuits Nominal pressure 25

DIN 3163 · Edition 10.1960 → withdrawn

Straight control valves for refrigerants · for nominal pressure 25 · dimensions, technical delivery conditions

DIN 3163 · Edition 4.1939 → withdrawn

Straight control valves for ammonia lines for ND 25

DIN 3164 edition 8.1974 → current

Position indicator for valves in refrigerant circuits

DIN 3166 edition 3.1983 → replaced by DIN EN 23166 edition 4.1995

Country name codes

DIN 3167 edition 4.1989 → replaced by DIN EN 810 edition 6.1997

Room air dehumidifier · Terms, testing of functional properties

DIN 3168 · Edition 4.1989 → current

Switch cabinet cooling devices · Terms, testing, labeling

DIN 3171 - Part 1 · Edition 2.2000 → withdrawn

Breathing equipment · Compressed gas cylinders for compressed air and compressed oxygen · Seamless steel cylinders, test pressure 300 bar and 450 bar

DIN 3171 - Part 1 · Edition 3.1997 → replaced by Edition 2.2000

Breathing equipment · Compressed gas cylinders for compressed air and compressed oxygen · Seamless steel cylinders, test pressure 300 bar and 450 bar

DIN 3171 - Part 1 · Edition 6.1971 → withdrawn

Seamless steel cylinders · for compressed air (compressed air) and compressed oxygen for breathing apparatus · test pressure 300 kp / cm² (+0300 bar)

DIN 3171 - Part 2 · Edition 2.2000 → withdrawn

Breathing equipment · Compressed gas cylinders for compressed air and compressed oxygen · Cylinders in composite construction, test pressure 300 bar and 450 bar

DIN 3171 - Part 2 · Edition 3.1997 → replaced by Edition 2.2000

Breathing equipment · Compressed gas cylinders for compressed air and compressed oxygen · Cylinders in composite construction, test pressure 300 bar and 450 bar

DIN 3171 edition 8.1990 → replaced by DIN 3171 part 1 edition 3.1997

Breathing equipment · Seamless steel cylinders for compressed air and compressed oxygen · Test pressure 300 bar and 450 bar

DIN 3171 edition 10.1977 → replaced by edition 8.1990

Breathing equipment · Seamless steel cylinders for compressed air (compressed air) and compressed oxygen · Test pressure 300 bar and 450 bar

DIN 3171 edition 7.1959 → withdrawn

Seamless steel bottles for compressed air and compressed oxygen for breathing apparatus

DIN 3171 edition 10.1937 → withdrawn

Oxygen devices · Seamless steel cylinders for compressed oxygen

DIN 3172 · Edition 5.1986 → withdrawn

Breathing equipment · Seamless pressurized gas cylinders made of aluminum alloys for compressed air and compressed oxygen · Test pressure 300 bar and 450 bar

DIN 3174 - Part 1 · Edition 4.2000 → withdrawn

Breathing equipment · cylinder valves · cylinder valves for compressed oxygen

DIN 3174 - Part 1 edition 9.1989 → replaced by edition 4.2000

Breathing equipment · Bottle valves for compressed oxygen

DIN 3174 - Part 10 Edition 9.1987 → withdrawn

Breathing equipment · cylinder valves for fire brigades · external dimensions

DIN 3174 edition 12.1977 → replaced by DIN 3174 part 1 edition 9.1989

Small cylinder valves for compressed oxygen

DIN 3174 Edition 3.1962 → withdrawn

Small cylinder valves for compressed oxygen · Main and connecting dimensions

DIN 3174 Edition 10.1937 → withdrawn

Oxygen devices · cylinder valves for oxygen cylinders

DIN 3175 edition 12.1987 → replaced by DIN EN 132 edition 5.1991

Respiratory protective equipment Definitions German version EN 132: 1986

DIN 3176 · Edition 10.1977 → withdrawn

Respiratory equipment · Alkali cartridges for respiratory protective equipment

DIN 3176 edition 9.1957 → withdrawn

Alkaline cartridges for breathing apparatus

DIN 3176 · Edition 5.1937 → withdrawn

Gas protection devices for respiratory protection · Alkali cartridges for oxygen protection devices

DIN 3177 · Edition 5.1963 → withdrawn

Breathing equipment · Air supply hose for fresh air hose devices

DIN 3177 edition 9.1937 → withdrawn

Gas protective devices for respiratory protection · Fresh air device · Claw coupling, air hose

DIN 3178 edition 4.1988 → replaced by DIN EN 135 edition 5.1991

Respiratory protection equipment · List of synonymous terms · German version EN 135: 1986

DIN 3179 - Part 1 Edition 7.1982 → current

Classification of breathing apparatus · Overview

DIN 3179 - Part 1 · Edition 11.1977 → replaced by Edition 7.1982

Classification of breathing apparatus · Overview

DIN 3179 - Part 1 · Edition 5.1966 → withdrawn

Classification of respiratory equipment · Respiratory protective equipment

DIN 3179 - Part 2 · Edition 2.1988 → replaced by DIN EN 133 Edition 5.1991

Respiratory protection equipment Classification German version EN 133: 1986

DIN 3179 - Part 2 · Edition 10.1982 → replaced by Edition 2.1988

Classification of breathing apparatus · Breathing apparatus for work and rescue for main use at ambient pressure (1 ^+0.2 _-0.3 ) bar

DIN 3179 - Part 2 Edition 9.1970 → withdrawn

Classification of breathing apparatus · Breathing connections · Names for individual parts

DIN 3179 - Part 3 · Edition 8.1976 → withdrawn

Classification of breathing apparatus · diving apparatus

DIN 3179 - Part 4 Edition 10.1982 → replaced by DIN EN 133 Edition 2.2002

Classification of breathing apparatus · Breathing apparatus for self-rescue for main use at ambient pressure (1 ^+0.2 _-0.3 ) bar

DIN 3179 - Part 4 Edition 9.1970 → withdrawn

Classification of breathing apparatus · Hose devices · Names for individual parts

DIN 3179 - Part 5 Edition 9.1969 → withdrawn

Classification of breathing apparatus · Containers with compressed air (short: compressed air breathing apparatus) · Designations for individual parts

DIN 3179 - Part 6 Edition 9.1969 → withdrawn

Classification of breathing apparatus · Circulators with pressurized oxygen (short: oxygen protection devices) · Names for individual parts

DIN 3180 - Part 1 · Edition 4.1988 → replaced by DIN EN 134 Edition 5.1991

Respiratory protection equipment Names of individual parts German version EN 134: 1986

DIN 3180 - Part 1 edition 10.1982 → replaced by edition 4.1988

Names for breathing apparatus · Breathing connections for breathing apparatus

DIN 3180 - Part 1 · Edition 12.1935 → withdrawn

Gas protective devices for respiratory protection · Name of individual parts

DIN 3180 - part 2 edition 10.1982 → replaced by DIN 3180 part 1 edition 4.1988

Names for breathing apparatus · Hose devices

DIN 3180 - part 3 edition 11.1982 → replaced by DIN 3180 part 1 edition 4.1988

Designations for breathing apparatus · Containers with compressed air (compressed air breathing apparatus)

DIN 3180 - part 4 edition 11.1982 → replaced by DIN 3180 part 1 edition 4.1988

Designations for breathing apparatus · Regeneration devices with compressed oxygen (oxygen protection devices)

DIN 3180 - part 5 edition 11.1983 → replaced by DIN 3180 part 1 edition 4.1988

Names for breathing apparatus · Filter apparatus

DIN 3180 - Part 5 Edition 3.1978 → replaced by Edition 11.1983

Names for breathing apparatus · Filter apparatus

DIN 3180 - Part 6 Edition 3.1978 → withdrawn

Terms for breathing apparatus Autonomous light diving apparatus with compressed air (compressed air)

DIN 3180 - Part 7 Edition 10.1981 → withdrawn

Names for breathing apparatus · Breathing connections for diving apparatus

DIN 3181 - Part 1 · Edition 5.1980 → replaced by DIN EN 141 Edition 6.1991

Respiratory equipment · Respiratory filters for respiratory protective equipment, gas and combination filters, safety requirements, testing, labeling

DIN 3181 - Part 1 · Edition 3.1980 → replaced by Edition 5.1980

Respiratory equipment · Respiratory filters for respiratory protective equipment, gas and combination filters, requirements, testing, labeling

DIN 3181 - Part 2 · Edition 5.1980 → replaced by DIN EN 143 Edition 5.1991

Respiratory equipment · Respiratory filter for respiratory protective equipment, particle filter, safety requirements, testing, labeling

DIN 3181 - Part 2 · Edition 3.1980 → replaced by Edition 5.1980

Respiratory equipment · Respiratory filter for respiratory protective equipment, particle filter, safety requirements, testing, labeling

DIN 3181 - Part 3 · Edition 2.1994 → withdrawn

Respiratory protection equipment · CO and reactor filters · Classification, labeling

The application of the standards DIN 58620 Edition 2.2007 and DIN 58621 Edition 10.2011 is recommended.

DIN 3181 - part 3 edition 11.1982 → replaced by edition 2.1994

Respiratory equipment · Respiratory filter for respiratory protective equipment · Special filter, labeling

DIN 3181 - part 4 edition 7.1988 → replaced by DIN EN 371 edition 5.1992

Respiratory equipment · Respiratory filter for respiratory protective equipment · Gas and combination filters of the gas filter type AX against low boilers · Safety requirements, testing, labeling

DIN 3181 edition 9.1957 → withdrawn

Respiratory filter for respiratory protective equipment · Labeling

DIN 3181 edition 1.1948 → withdrawn

Gas protective devices for respiratory protection · Respiratory filter, labeling

DIN 3182 - Part 1 · Edition 4.1996 → withdrawn

Breathing apparatus, diving equipment · Round thread · Theoretical profile

DIN 3182 - Part 1 · Edition 6.1989 → replaced by Edition 4.1996

Respiratory protection · Round thread · Theoretical profile

DIN 3182 - part 1 edition 9.1957 → replaced by edition 6.1989 and DIN 3183 part 2 edition 5.1988

Round thread for breathing apparatus · Theoretical profile

DIN 3182 - Part 2 · Edition 4.1996 → withdrawn

Breathing apparatus, diving equipment · Round thread · Thread go ring gauges and thread no-go ring gauges

DIN 3182 - Part 2 · Edition 6.1989 → replaced by Edition 4.1996

Respiratory protection equipment · round thread · thread ring gauges and thread ring gauges

DIN 3182 - part 2 edition 9.1957 → replaced by edition 6.1989 and DIN 3183 part 2 edition 5.1988

Round thread for breathing apparatus · Thread ring gauges and reject ring gauges

DIN 3182 - Part 3 · Edition 4.1996 → withdrawn

Breathing apparatus, diving equipment · Round thread · Thread plug gauges

DIN 3182 - Part 3 · Edition 6.1989 → replaced by Edition 4.1996

Respiratory protection equipment · round thread · thread plug gauges

DIN 3182 - part 3 edition 9.1957 → replaced by edition 6.1989 and DIN 3183 part 2 edition 5.1988

Round thread for breathing apparatus · Thread plug gauges

DIN 3182 edition 9.1937 → withdrawn

Gas protection devices for respiratory protection · Round thread

DIN 3183 - part 1 edition 5.1988 → replaced by DIN EN 148 part 2 edition 4.1999

Breathing apparatus · Threads for breathing connections · Central thread connection · German version EN 148-2: 1987

DIN 3183 - Part 1 · Edition 6.1981 → replaced by Edition 5.1988

Connections for breathing apparatus · Central thread connections

DIN 3183 - part 2 edition 5.1988 → replaced by DIN EN 148 part 1 edition 4.1999

Breathing apparatus · Threads for breathing connections · Round thread connection · German version EN 148-1: 1987

DIN 3183 - Part 2 · Edition 6.1981 → replaced by Edition 5.1988

Connections for breathing apparatus · Round thread connections

DIN 3183 - Part 3 · Edition 4.1990 → withdrawn

Connections for breathing apparatus · Trapezoidal thread connection Tr 50 × 3 for diving apparatus

DIN 3183 - Part 3 · Edition 4.1982 → replaced by Edition 4.1990

Connections for breathing apparatus · Threaded connection for diving apparatus

DIN 3183 - part 10 edition 4.1984 → replaced by DIN EN 148 part 3 edition 8.1992

Connections for breathing apparatus · M 45 × 3 thread connections for fire brigades

DIN 3183 edition 11.1961 → withdrawn

Connections for breathing apparatus · Connection dimensions for sealing rings

DIN 3183 · Edition 7.1944 → withdrawn

Gas protection devices for respiratory protection · Connections

DIN 3184 edition 9.1957 → withdrawn

Clear lens for breathing apparatus

DIN 3184 edition 9.1941 → withdrawn

Gas protection devices for respiratory protection · Clear lens for gas masks

DIN 3188 edition 9.1984 → replaced by DIN EN 12021 edition 1.1999

Compressed air for breathing apparatus · Safety requirements and testing

DIN 3188 edition 9.1981 → replaced by edition 9.1984

Compressed air for breathing apparatus · Safety requirements and testing

DIN 3188 · Edition 1.1974 → withdrawn

Compressed air (compressed air) for breathing apparatus

DIN 3198 edition 4.1956 → withdrawn

Ash pods for urns

DIN 3198 edition 4.1931 → withdrawn

Ash pods for urns - funeral services

1st edition of the standard

DIN 3199 Edition 3.1942 → withdrawn

Cremation coffin · Largest dimensions and design

DIN 3201 edition 10.1943 → withdrawn

Wedge and knife gate valves made of gray cast iron and cast steel · Area of ​​application, nominal pressure, test pressure, operating pressure, operating temperature

DIN 3202 - Part 1 edition 9.1984 → replaced by DIN EN 558 Part 1 edition 12.1995

Installation lengths of fittings · Flanged fittings

DIN 3202 - Part 1 · Edition 2.1977 → replaced by Edition 9.1984

Installation lengths of fittings · Flanged fittings

DIN 3202 - Part 1 · Edition 7.1973 → withdrawn

Installation lengths of fittings · Flanged fittings

DIN 3202 - Part 2 · Edition 4.1982 → replaced by DIN EN 12982 Edition 3.2000

Installation lengths of fittings · Weld-in fittings

DIN 3202 - Part 2 · Edition 7.1973 → withdrawn

Installation lengths of fittings · Weld-in fittings

DIN 3202 - Part 3 Edition 10.1979 → replaced by DIN EN 558 Part 1 Edition 12.1995

Overall lengths of fittings · Clamp fittings

DIN 3202 - Part 4 Edition 4.1982 → replaced by DIN EN 16722 Edition 12.2015

Overall lengths of fittings · Fittings with internal thread connection

DIN 3202 - Part 4 · Edition 4.1978 → replaced by Edition 4.1982

Overall lengths of fittings · Fittings with internal thread connection

DIN 3202 - Part 5 · Edition 9.1984 → withdrawn

Overall lengths of fittings · Fittings with pipe screw connection

DIN 3202 - Part 5 · Edition 8.1977 → replaced by Edition 9.1984

Overall lengths of fittings · Fittings with pipe screw connection

DIN 3202 edition 10.1943x → withdrawn

Wedge and knife gate valves made of gray cast iron and cast steel · Nominal widths and lengths · Nominal pressure 6 (2.5) to 400

Cross edition 7.1954

DIN 3203 edition 12.1943 → withdrawn

Fittings · Gate valve · Assignment of the constriction

DIN 3204 edition 10.1942xx → withdrawn

Wedge gate valve for heating systems for nominal pressure 4 with flange connection according to nominal pressure 6

Cross edition 11.1950

DIN 3204 · Edition 4.1928 → withdrawn

Flat slide valve with flange connection according to nominal pressure 2.5

DIN 3205 edition 4.1928 → withdrawn

Flat slide valve with flange connection according to nominal pressure 10

DIN 3206 edition 4.1928 → withdrawn

Oval gate valve with flange connection according to nominal pressure 10

DIN 3207 edition 4.1928 → withdrawn

Oval gate valve with socket connection according to nominal pressure 10

DIN 3208 edition 4.1928 → withdrawn

Round gate valve with flange connection according to nominal pressure 10 and 16

DIN 3210 · Edition 6.1972 → withdrawn

Connection types of electric actuators for valves · Nominal torques, sizes, requirements

DIN 3211 - part 1 edition 11.1985 → replaced by DIN EN 736 part 1 edition 4.1995

Valves · Terms and definitions

DIN 3211 edition 11.1977 → replaced by DIN 3211 part 1 edition 11.1985

Pipe fittings · Terms

DIN 3213 edition 11.1989 → replaced by DIN EN 816 edition 1.1997

Self-closing fittings for the water supply PN 10 · General requirements and tests

DIN 3214 - Part 1 edition 3.1984 → replaced by DIN EN 200 edition 7.1990

Sanitary fittings · General requirements and tests

DIN 3214 - Part 2 Edition 3.1984 → replaced by DIN EN 200 Edition 7.1990

Sanitary fittings · Connection dimensions for jet regulators

DIN 3214 - Part 3 Edition 3.1984 → withdrawn

Sanitary fittings · Connection dimensions for connection of the upper part of the housing

DIN 3214 - Part 4 Edition 3.1984 → replaced by DIN EN 200 Edition 7.1990

Sanitary fittings · Wall connection dimensions for wall batteries

DIN 3214 - Part 11 Edition 3.1984 → replaced by DIN EN 200 Edition 7.1990

Sanitary fittings · Undercounter mixer · Dimensions

DIN 3214 - Part 12 Edition 3.1984 → replaced by DIN EN 246 Edition 1.1990

Sanitary fittings · aerators · dimensions

DIN 3214 - Part 13 · Edition 3.1984 → replaced by DIN EN 200 Edition 7.1990

Sanitary fittings · Wall faucets · Dimensions

DIN 3214 - Part 14 Edition 3.1990 → replaced by DIN EN 246 Edition 11.2003

Sanitary fittings Jet regulator, flow class Z Dimensions, special requirements and testing (extension to DIN EN 246)

DIN 3216 edition 10.1942x → withdrawn

Wedge gate valve made of gray cast iron with flange connection according to nominal pressure 10 and 2.5

Cross edition 9.1953

DIN 3218 edition 10.1943x → withdrawn

Fittings · Flat wedge gate valve for gas · (light model) made of gray cast iron with flange connection according to nominal pressure 2.5

Cross edition 1.1955

DIN 3220 · Edition 4.2002 → current

Handwheels, flat · Hub hole with tapered square

DIN 3220 edition 4.1973 → replaced by edition 4.2002

Handwheels, flat · Hub hole tapered square

DIN 3220 edition 12.1935 → withdrawn

Handwheels, flat · with tapered square hole, for fittings

DIN 3221 edition 1.1986 → replaced by DIN EN 14339 edition 10.2005

Underground hydrants PN 16

DIN 3221 - part 1 edition 3.1978 → replaced by DIN 3221 edition 1.1986

Underground hydrants for fire extinguishing purposes · Dimensions

DIN 3221 - part 2 edition 4.1978 → replaced by DIN 3221 edition 1.1986

Underground hydrants for fire extinguishing purposes · Requirements, testing

DIN 3221 · Edition 6.1943 → withdrawn

Underground hydrant · 80 mm nominal connection width, 70 mm nominal valve width for fire-fighting purposes

DIN 3222 edition 1.1986 → replaced by DIN EN 14384 edition 10.2005

Post hydrants PN 16

DIN 3222 - Part 1 edition 9.1978 → replaced by DIN 3222 edition 1.1986

Above ground hydrants for fire extinguishing purposes · Dimensions

DIN 3222 - Part 2 edition 9.1978 → replaced by DIN 3222 edition 1.1986

Above ground hydrants for fire extinguishing purposes · Requirements, testing

DIN 3222 edition 10.1942x → withdrawn

Underground hydrants for fire extinguishing purposes, 80 mm and 100 mm connection and valve sizes

Cross edition 6.1943

DIN 3223 Edition 11.2012 → current

Actuating key for fittings

The standard specifies the requirements for operating keys for fittings such as post hydrants, underground hydrants, gate valves with square protectors, tapping fittings

DIN 3223 / A1 edition 6.2002 → replaced by edition 11.2012

Actuation key for fittings · Amendment A1

DIN 3223 edition 11.1974 → replaced by edition 11.2012

Actuating key for fittings

DIN 3223 edition 8.1936 → withdrawn

Key for underground hydrant according to DIN 3221

DIN 3225 edition 10.1942xx → withdrawn

Oval wedge valve made of gray cast iron with flange connection according to nominal pressure 10

Cross edition 1.1954

DIN 3226 edition 10.1942xx → withdrawn

Round wedge valve made of gray cast iron for nominal pressure 16

Cross edition 2.1952

DIN 3227 edition 4.2008 → current

Fittings for drinking water systems in buildings · Angle valves · Requirements and tests

The standard specifies requirements and test methods for angle valves that are used in drinking water installations according to DIN 1988 Part 2.

DIN 3227 edition 10.2002 → replaced by edition 4.2008

Fittings for drinking water systems in buildings · Angle valves · Requirements and tests

DIN 3228 edition 10.1943x → withdrawn

Wedge gate valve made of cast steel, with flange connection according to nominal pressure 10

Cross edition 11.1952

DIN 3229 edition 10.1942x → replaced by DIN 3352 parts 1, 6 and 7 edition 5.1979

Wedge oval gate valve made of cast steel for nominal pressure 16, fittings

Cross edition 12.1949

DIN 3230 - part 1 edition 4.1974 → replaced by DIN EN 12266 part 1 edition 6.2003

Technical delivery conditions for fittings · Inquiry, order and delivery

DIN 3230 - part 2 edition 4.1974 → replaced by DIN EN 12570 edition 10.2000 and DIN EN 12266 part 1 edition 6.2003

Technical delivery conditions for valves · General requirements

DIN 3230 - part 3 edition 4.1982 → replaced by DIN EN 12266 part 1 edition 6.2003 and DIN EN 12266 part 2 edition 5.2003

Technical delivery conditions for fittings · List of possible tests

DIN 3230 - Part 4 Edition 3.1977 → withdrawn

Technical delivery conditions for fittings · Fittings for drinking water · Requirements and testing

The application of the standards DIN EN 1074 parts 1, 2, 3, 4, 5 and 6 is recommended.

DIN 3230 - Part 5 Edition 11.2014 → current

Technical delivery conditions for shut-off fittings · Shut-off fittings for gas pipes and gas systems · Requirements and tests

DIN 3230 - Part 5 Edition 8.1984 → replaced by Edition 11.2014

Technical delivery conditions for fittings · Fittings for gas pipes and gas systems · Requirements and testing

DIN 3230 - Part 5 Edition 9.1981 → replaced by Edition 8.1984

Technical delivery conditions for valves · Shut-off valves for gas pipes and gas systems · Requirements and testing

DIN 3230 - Part 6 Edition 9.1987 → current

Technical delivery conditions for fittings · Fittings for flammable liquids · Requirements and testing

DIN 3230 - Part 6 Edition 12.1980 → replaced by Edition 9.1987

Technical delivery conditions for fittings · Fittings for flammable liquids · Requirements and testing

DIN 3230 edition 2.1953 → withdrawn

Large and steam fittings · Technical delivery conditions

DIN 3231 edition 9.1953 → withdrawn

Area of ​​application for check valves made of gray cast iron and cast steel · Nominal pressure, test pressure, operating pressure, operating temperature

DIN 3231 edition 10.1943 → withdrawn

Check valves made of gray cast iron and cast steel · Area of ​​application, nominal pressure, test pressure, operating pressure, operating temperature

DIN 3232 edition 12.1943 → withdrawn

Nominal widths and lengths for check valves made of gray cast iron and cast steel Nominal pressure 6 to 320

DIN 3233 edition 10.1943 → withdrawn

Spindle square and handwheel hubs of fittings

DIN 3234 edition 12.1943 → withdrawn

Spindle diameter of fittings

DIN 3236 - Part 1 Edition 10.1994 → replaced by DIN 11869

Flow-through sight glass fittings with seal in the force shunt · Without lining

DIN 3236 - Part 2 Edition 2.1996 → replaced by DIN 11869

Flow sight glass fittings with seal in the force shunt · With enamel lining

DIN 3237 - Part 1 Edition 10.1994 → replaced by DIN 11869

Flow-through sight glass fittings with seal in the main power circuit · Without lining

DIN 3237 - Part 1 · Edition 8.1991 → replaced by Edition 10.1994

Flow-through sight glass fitting with round sight glass plates

DIN 3237 - Part 2 Edition 10.1994 → replaced by DIN 11869

Flow sight glass fittings with seal in the main power circuit · With plastic lining

DIN 3237 - Part 3 Edition 3.1996 → replaced by DIN 11869

Flow sight glass fittings with seal in the main power circuit · With rubber lining

DIN 3238 Edition 11.2001 → current

Compressed air couplings · Claw coupling, 42 mm claw spacing, with lock nut - external thread, internal thread and hose coupling, sealing ring

DIN 3238 - Part 1 edition 7.1984 → replaced by DIN 3238 edition 11.2001

Compressed air fittings · Claw screw couplings · External thread, internal thread and hose couplings, 42 mm claw spacing

DIN 3238 - Part 2 edition 7.1984 → replaced by DIN 3238 edition 11.2001

Compressed air fittings · Claw screw couplings · Seal

DIN 3239 - part 1 edition 10.1988 → replaced by DIN EN 12627 edition 10.1999

Butt weld ends on fittings · weld ends

DIN 3239 - Part 1 edition 10.1980 → replaced by edition 10.1988

Butt weld ends on fittings · weld ends

DIN 3239 - Part 2 · Edition 2.1978 → replaced by DIN EN 12760 Edition 12.1999

Butt weld ends on fittings · socket weld ends

DIN 3240 edition 7.1943x → withdrawn

Fittings · Hot draft valve · Installation and connection dimensions

Cross edition 10.1948

DIN 3241 edition 4.1944 → withdrawn

Winderheater slide without relief plate

DIN 3242 edition 4.1944 → withdrawn

Cooker slider with relief plate

DIN 3245 · Edition 10.1944 → withdrawn

Wind heater · access lock · construction and connection dimensions

DIN 3246 edition 10.1944 → withdrawn

Wind heater · Dome lock · Construction and connection dimensions

DIN 3247 Edition 3.2017 → current

Suction baskets with flange without backflow preventer

The standard specifies the design, dimensions, designations and material for suction baskets with a flange without a backflow preventer.

DIN 3247 edition 6.1985 → replaced by edition 3.2017

Suction baskets with flange without backflow preventer

DIN 3248 · Edition 3.2017 → current

Suction baskets with internal thread connection without backflow preventer

The standard specifies the design, dimensions, designations and material for suction baskets with an internal thread connection without a backflow preventer.

DIN 3248 edition 6.1985 → replaced by edition 3.2017

Suction baskets with internal thread connection without backflow preventer

DIN 3249 Edition 3.2017 → current

Suction baskets with female thread connection with backflow preventer (foot valve)

The standard specifies the design, dimensions, designations, materials and seals for suction baskets with an internal thread connection and with a foot valve for vertical installation.

DIN 3249 · Edition 6.1985 → replaced by Edition 3.2017

Suction baskets with female thread connection with backflow preventer (foot valve)

DIN 3250 Edition 10.1932 → withdrawn

Gas shut-off cocks with double-sided socket connection

DIN 3251 edition 10.1932 → withdrawn

Gas shut-off valves · with socket and screw connection with internal thread

DIN 3252 edition 10.1932 → withdrawn

Gas shut-off valves · Outlets with internal thread

DIN 3253 edition 2.1971 → withdrawn

Gas fittings for commercial installation · Gas hose taps · with internal and external thread

DIN 3253 edition 1.1955 → withdrawn

Small gas fittings · Hose taps · Operating pressure up to 200 mm WS · Main dimensions

DIN 3253 edition 3.1943x → withdrawn

Hose taps

Cross edition

DIN 3254 edition 2.1971 → withdrawn

Gas fittings for commercial installation · Gas hose nozzles with internal and external threads

DIN 3254 edition 1.1955 → withdrawn

Hose nozzles · main dimensions

DIN 3254 edition 3.1943x → withdrawn

Hose nozzles

Cross edition

DIN 3255 - Part 1 edition 1.1973 → replaced by DIN EN 1106 edition 4.2001

Adjustment elements for gas appliances for cooking, baking and grilling

DIN 3255 - Part 1 · Edition 8.1957 → withdrawn

Gas appliances · Adjusting elements for household cooking appliances · Terms, construction, quality, performance and testing

DIN 3255 - Part 2 edition 1.1973 → replaced by DIN EN 1106 edition 4.2001

Adjustment elements for gas appliances for space heating

DIN 3255 - Part 3 · Edition 12.1976 → withdrawn

Adjustment elements for gas appliances, for liquid gas-powered camping cooking appliances · Safety requirements and tests

DIN 3255 - Part 4 Edition 10.1979 → withdrawn

Setting devices for gas consumption devices for gas-operated refrigerators and freezers · Safety requirements and testing

DIN 3255 edition 11.1938 → withdrawn

Taps for gas cookers, gas roasters and gas stoves for the household

DIN 3257 edition 1.1955 → withdrawn

Small gas fittings · Double hose taps · Operating pressure up to 200 mm WS · Main dimensions

DIN 3257 edition 7.1944 → withdrawn

Double hose taps

DIN 3258 - Part 1 · Edition 2.1971 → replaced by DIN EN 125 Edition 9.1991

Flame monitoring on gas consumption devices · Ignition fuses

DIN 3258 - Part 2 · Edition 7.1988 → withdrawn

Flame monitoring on gas appliances · Automatic ignition safeguards · Safety requirements and testing

DIN 3258 - part 2 edition 11.1977 → replaced by edition 7.1988

Flame monitoring at gas consumption devices · Automatic ignition safeguards

DIN 3258 edition 11.1956 → withdrawn

Ignition fuses for gas appliances and fireplaces · Terms, construction, quality, performance and testing

DIN 3259 · Edition 3.2017 → current

Suction baskets with flange with backflow preventer (foot valve)

The standard specifies the design, dimensions, designations, material and seals for suction baskets with flange and with foot valve for vertical installation.

DIN 3259 · Edition 6.1985 → replaced by Edition 3.2017

Suction baskets with flange with backflow preventer (foot valve)

DIN 3260 edition 12.1954 → withdrawn

Domestic water meter for cold water

DIN 3260U edition 11.1943 → withdrawn

Domestic water meter for cold water

Conversion standard

DIN 3261U edition 7.1940x → withdrawn

Domestic water meter for cold water · Screw connections

Conversion norm; Cross edition 11.1943

DIN 3265 - Part 1 edition 9.1986 → replaced by DIN EN 12541 edition 3.2003

Sanitary fittings - flush valves - flush valves for toilet bowls · Dimensions, requirements

The standard specifies the dimensions and requirements for flush valves for toilet bowls, which are installed in building drainage systems in accordance with DIN 1986 Part 1 and connected to drinking water pipes in accordance with the DIN 1988 series.

DIN 3265 - Part 1 · Edition 1.1970 → replaced by Edition 9.1986

Sanitary fittings · Flush valves · Dimensions, requirements, technical regulations

DIN 3265 - Part 2 Edition 7.1987 → replaced by DIN EN 12541 Edition 3.2003

Sanitary fittings - Pressure flushers - Pressure flushers for toilet bowls · Tests

The standard applies to the type test of flush valves according to DIN 3265 Part 1, edition 9.1986.

DIN 3265 - Part 2 · Edition 2.1966 → replaced by Edition 7.1987

Sanitary fittings · Flush valves · Type examination

DIN 3265 - part 3 edition 5.1990 → replaced by DIN EN 12541 edition 3.2003

Sanitary fittings - flush valves - flush valves for urinals · Dimensions, requirements

DIN 3265 - Part 4 Edition 5.1990 → replaced by DIN EN 12541 Edition 3.2003

Sanitary fittings - Pressure flushers - Pressure flushers for urinals · Tests

DIN 3265 edition 8.1939 → withdrawn

Abortion flush valve · Rules for construction and operation

DIN 3266 · Edition 5.2009 → current

Fittings for drinking water installations in properties and buildings · Pipe aerators types D and E · Requirements and tests

DIN 3266 - Part 1 edition 7.1986 → replaced by DIN 3266 edition 5.2009, DIN EN 14452 edition 8.2005 and DIN EN 14453 edition 8.2005

Fittings for drinking water installations in properties and buildings Pipe breakers, pipe disconnectors, pipe aerators, PN 10

DIN 3266 - Part 2 edition 12.1987 → replaced by DIN 3266 edition 5.2009, DIN EN 14452 edition 8.2005 and DIN EN 14453 edition 8.2005

Fittings for drinking water installations in properties and buildings · pipe interrupter, pipe disconnector, pipe aerator, PN 10 · test

DIN 3266 edition 3.1979 → replaced by DIN 3266 part 1 edition 7.1986

Pipe aerator for drinking water pipes

DIN 3266 edition 9.1940 → withdrawn

Rules for the construction and operation of pipe aerators for water pipes

DIN 3267 edition 2.1972 → current

Flush pipes for flush valves

DIN 3268 edition 8.1989 → withdrawn

Plastic flush pipes for cisterns

DIN 3269 - part 1 edition 1.1988 → replaced by DIN EN 13959 edition 1.2005

Valves for drinking water installations in properties and buildings · Backflow preventer PN 10 · Requirements

DIN 3269 - part 2 edition 1.1988 → replaced by DIN EN 13959 edition 1.2005

Fittings for drinking water installations in properties and buildings · Backflow preventer PN 10 · Test

DIN 3270 edition 12.1974 → withdrawn

Sanitary fittings · Bathtub waste and overflow fitting, drain R 1½ (40 mm) and R 2 (50 mm)

DIN 3271 edition 10.1928 → withdrawn

Globe valves up to nominal pressure 10, operating pressure W 10 · Overview

DIN 3272 edition 10.1928 → withdrawn

Globe valves · Housing with internal connection thread on the inlet and outlet side

For operating pressure W 10; Construction sheet

DIN 3273 Edition 10.1928 → withdrawn

Straight-way valves · Housing with internal connection thread on the inlet and outlet side and drainage plugs on both sides

For operating pressure W 10; Construction sheet

DIN 3274 edition 9.1930 → withdrawn

Globe valves up to nominal pressure 10 · Housing with internal thread at the inlet and screw connection at the outlet

1st edition of the standard

DIN 3275 edition 9.1930 → withdrawn

Straight-way valves up to nominal pressure 10 · Housing with soldered socket at the inlet and screw connection at the outlet

1st edition of the standard

DIN 3276 · Edition 10.1928 → withdrawn

Outlet valves up to nominal pressure 10, operating pressure W 10 · Overview

DIN 3277 edition 10.1928 → withdrawn

Drain valves · Housing

For operating pressure W 10; Construction sheet

DIN 3278 edition 10.1928 → withdrawn

Drain valves · Housing for hose screw connection

For operating pressure W 10; Construction sheet

DIN 3279 edition 10.1928 → withdrawn

Valve bonnets

Construction sheet

DIN 3280 edition 4.1988 → current

Water fittings for house installations · Screw connections nominal pressure 10 (with cone seal) · Overview

DIN 3280 edition 8.1976 → replaced by edition 4.1988

Small water fittings · Screw connections up to nominal pressure 10 (with cone seal) · Overview

DIN 3280 edition 3.1933xx → withdrawn

Small gas and water fittings · Screw connections up to nominal pressure 10 · Operating pressure I (W) 10 (with cone seal) · Overview

Cross edition 9.1954

DIN 3281 edition 4.1988 → current

Water fittings for house installations · Suction cup nominal pressure 10 (with cone seal) · Overview

DIN 3281 edition 7.1976 → replaced by edition 4.1988

Small water fittings · Suction cups up to nominal pressure 10 (with cone seal) · Overview

DIN 3281 edition 3.1933xx → withdrawn

Small gas and water fittings · Suction cups up to nominal pressure 10 · Operating pressure I (W) 10 (with cone seal) · Overview

Cross edition 10.1956

DIN 3282 edition 7.1976 → withdrawn

Small water fittings · Suction cups and screw connections up to nominal pressure 10 · Lead pipe outlets

DIN 3282 edition 10.1928x → withdrawn

Lead pipe outlets

Cross edition 7.1940

DIN 3283 · Edition 4.1988 → current

Water fittings for house installations · suction cups and screw connections nominal pressure 10 · outlets with internal thread

DIN 3283 edition 7.1976 → replaced by edition 4.1988

Small water fittings · Suction cups and screw connections up to nominal pressure 10 · Outlets with internal thread

DIN 3283 edition 3.1933x → withdrawn

Small gas and water fittings · Suction cups and screw connections up to nominal pressure 10 · Outlets with internal thread

Cross edition 7.1940

DIN 3284 · Edition 4.1988 → current

Water fittings for house installations · suction cups and screw connections nominal pressure 10 · outlets with external thread

DIN 3284 edition 7.1976 → replaced by edition 4.1988

Small water fittings · Suction cups and screw connections up to nominal pressure 10 · Outlets with external thread

DIN 3284 edition 2.1938x → withdrawn

Small gas and water fittings · suction cups and screw connections up to nominal pressure 10 · outlets with external thread

Cross edition 7.1940

DIN 3285 · Edition 4.1988 → current

Water fittings for house installations · suction cups and screw connections nominal pressure 10 · hose outlets

DIN 3285 edition 7.1976 → replaced by edition 4.1988

Small water fittings · Suction cups and screw connections up to nominal pressure 10 · Hose outlets

DIN 3285 edition 3.1933xx → withdrawn

Small gas and water fittings · suction cups and screw connections up to nominal pressure 10 · hose outlets

Cross editions 7.1940 and 7.1957

DIN 3286 edition 7.1976 → withdrawn

Small water fittings · Suction cups and screw connections up to nominal pressure 10 · Male parts for lead pipe screw connections

DIN 3286 edition 3.1933xx → withdrawn

Small gas and water fittings · Suction cups and screw connections up to nominal pressure 10 · Male parts for lead pipe screw connections

Cross editions 7.1940 and 9.1957

DIN 3287 · Edition 4.1988 → current

Water fittings for house installations · Suckers and screw connections nominal pressure 10 · Male parts for pipe screw connections

DIN 3287 edition 7.1976 → replaced by edition 4.1988

Small water fittings · Suction cups and screw connections up to nominal pressure 10 · Male parts for steel pipe screw connections

DIN 3287 edition 3.1933xx → withdrawn

Small gas and water fittings · suction cups and screw connections up to nominal pressure 10 · male parts for steel pipe screw connections

Cross editions 7.1940 and 9.1957

DIN 3288 edition 3.1933x → withdrawn

Suction cups and screw connections up to nominal pressure 10 · Male parts with internal thread for screw connections

Cross edition 7.1940

DIN 3289 · Edition 4.1988 → current

Water fittings for house installations · suction cups and screw connections nominal pressure 10 · male parts for suction cups

DIN 3289 edition 7.1976 → replaced by edition 4.1988

Small water fittings · Suction cups and screw connections up to a nominal pressure of 10 · Male parts for suction cups

DIN 3289 edition 3.1933xx → withdrawn

Small gas and water fittings · suction cups and screw connections up to nominal pressure 10 · male parts for suction cups · for outlets with external thread or lead pipe outlets

Cross editions 7.1940 and 9.1957

DIN 3290 edition 3.1933x → withdrawn

Suction cups and screw connections up to nominal pressure 10 · Male parts for suction cups for outlets with internal thread

Cross edition 7.1940

DIN 3291 edition 4.1988 → current

Water fittings for house installations · suction cups and screw connections nominal pressure 10 · male parts for hose screw connections

DIN 3291 edition 7.1976 → replaced by edition 4.1988

Small water fittings · Suckers and screw connections up to nominal pressure 10 · Male parts for hose screw connections

DIN 3291 edition 3.1933xx → withdrawn

Small gas and water fittings · Suction cups and screw connections up to nominal pressure 10 · Male parts for hose screw connections

Cross edition 9.1954

DIN 3292 - Part 1 · Edition 6.1984 → current

Fittings for house installation · Union nuts made of non-ferrous metals

DIN 3292 - Part 1 · Edition 2.1964 → replaced by Edition 6.1984

Gas and water fittings for house installation · Union nuts made of non-ferrous metals, for screw connections up to 10 kp / cm² operating pressure

DIN 3292 - Part 2 · Edition 6.1984 → current

Fittings for house installation · Union nuts made of malleable cast iron

DIN 3292 - Part 2 · Edition 2.1964 → replaced by Edition 6.1984

Gas and water fittings for house installation · Union nuts made of malleable cast iron, for screw connections up to 10 kp / cm² operating pressure

DIN 3292U edition 3.1937 → withdrawn

Suction cups and screw connections up to ND 10 Union nuts up to ND 10

Conversion standard

DIN 3292 Edition 3.1933 → withdrawn

Suction cups and screw connections up to a nominal pressure of 10 · Union nuts

DIN 3293 - Part 1 · Edition 2.1964 → withdrawn

Water fittings for house installation · Toggle union nuts made of non-ferrous metals, for hose screw connections up to 10 kp / cm² operating pressure

DIN 3293 - Part 2 · Edition 2.1964 → withdrawn

Water fittings for house installation · Toggle union nuts made of malleable cast iron, for hose screw connections up to 10 kp / cm² operating pressure

DIN 3293U edition 9.1937 → withdrawn

Suction cups and screw connections up to ND 10 · Toggle union nuts for hose screw connections

Conversion standard

DIN 3293 Edition 3.1933 → withdrawn

Suction cups and screw connections up to nominal pressure 10 · Toggle union nuts for hose screw connections

DIN 3296 edition 8.1988 → withdrawn

Sanitary fittings · Valve plugs for sinks, sinks, bathtubs

DIN 3296 edition 2.1972 → replaced by edition 8.1988

Sanitary fittings · Valve plugs for sinks, sinks, bathtubs

DIN 3296 edition 4.1944 → withdrawn

Valve plugs for sinks, sinks, bathtubs

DIN 3297 edition 8.1974 → withdrawn

Universal valves for washstands, sinks and sinks

DIN 3298 edition 8.1974 → withdrawn

Shaft valves for washstands, sinks and sinks

DIN 3299 edition 2.1975 → withdrawn

Waste and overflow fittings R1½, for sinks

DIN 3300 edition 10.1943 → withdrawn

Shut-off and check valves · Straight and corner shape · Overall length for ND 6 to 320

DIN 3301 edition 12.1930 → withdrawn

Straight and angle valves · Overview of the valves with standardized individual parts

2nd edition of the standard

DIN 3302 edition 12.1930 → withdrawn

Globe valves for nominal pressure 6 · Operating pressures: I (W) 6; II (G) 5 main dimensions

2nd edition of the standard

DIN 3303 edition 12.1930 → withdrawn

Globe valves for nominal pressure 10 · Operating pressures: I (W) 10; II (G) 8 main dimensions

2nd edition of the standard

DIN 3304 edition 12.1930 → withdrawn

Straight through valves for nominal pressure 16 · Operating pressures: I (W) 16; II (G) 13 main dimensions

2nd edition of the standard

DIN 3305 edition 12.1930 → withdrawn

Globe valves for nominal pressure 25 · Operating pressures: I (W) 25; II (G) 20; III (H) 20 main dimensions

2nd edition of the standard

DIN 3306 edition 12.1930 → withdrawn

Globe valves for nominal pressure 40 · Operating pressures: I (W) 40; II (G) 32; III (H) 32 main dimensions

2nd edition of the standard

DIN 3307 edition 12.1930 → withdrawn

Globe valves · Housing for nominal pressure 6 · Operating pressures: I (W) 6; II (G) 5

2nd edition of the standard

DIN 3308 edition 12.1930 → withdrawn

Globe valves · Housing for nominal pressure 10 · Operating pressures: I (W) 10; II (G) 8

2nd edition of the standard

DIN 3309 edition 12.1930 → withdrawn

Globe valves · Housing for nominal pressure 16 · Operating pressures: I (W) 16; II (G) 13

2nd edition of the standard

DIN 3310 edition 12.1930 → withdrawn

Globe valves · Housing for nominal pressure 25 · Operating pressures: I (W) 25; II (G) 20; III (H) 20

2nd edition of the standard

DIN 3311 edition 12.1930 → withdrawn

Globe valves · Housing for nominal pressure 40 · Operating pressures: I (W) 40; II (G) 32; III (H) 32

2nd edition of the standard

DIN 3312 edition 12.1930 → withdrawn

Straight and angle valves · Cover for nominal pressure 6 to 40 · Construction sheet

2nd edition of the standard

DIN 3313 edition 12.1930 → withdrawn

Straight and angle valves · cone and seat ring for nominal pressure 6 to 40 · construction sheet

2nd edition of the standard

DIN 3314 edition 12.1930 → withdrawn

Straight and angle valves cone mounting for nominal pressure 6 to 40

2nd edition of the standard

DIN 3315 edition 12.1930 → withdrawn

Straight and angle valves · Spindle square, handwheel attachment for nominal pressure 6 to 40 · Construction sheet

2nd edition of the standard

DIN 3316 edition 12.1930 → withdrawn

Straight and angle valves Stuffing box and base ring for nominal pressure 6 to 40

2nd edition of the standard

DIN 3317 edition 12.1930 → withdrawn

Straight and angle valves · Bridge for nominal pressure 6 to 40

2nd edition of the standard

DIN 3318 edition 12.1930 → withdrawn

Straight and angle valves Columns for nominal pressure 6 to 40

2nd edition of the standard

DIN 3319 · Edition 4.2002 → current

Handwheels, offset · Hub hole with tapered square

DIN 3319 edition 4.1973 → replaced by edition 4.2002

Handwheels, offset · Hub hole tapered square

DIN 3319 · Edition 12.1930 → withdrawn

Handwheels with full rim and tapered square hole, only for fittings

2nd edition of the standard

DIN 3320 - Part 1 edition 9.1984 → withdrawn

Safety valves · Safety shut-off valves · Terms, sizing, labeling

DIN 3320 edition 1.1972 → replaced by DIN 3320 part 1 edition 9.1984

Safety valves · Terms

DIN 3321 · Edition 6.1987 → withdrawn

Requirements and approval tests for hydrants

DIN 3322 edition 12.1930 → withdrawn

Angle valves for nominal pressure 6 · Operating pressures: I (W) 6; II (G) 5 main dimensions

2nd edition of the standard

DIN 3323 edition 12.1930 → withdrawn

Angle valves for nominal pressure 10 · Operating pressures: I (W) 10; II (G) 8 main dimensions

2nd edition of the standard

DIN 3324 edition 12.1930 → withdrawn

Angle valves for nominal pressure 16 · Operating pressures: I (W) 16; II (G) 13 main dimensions

2nd edition of the standard

DIN 3325 edition 12.1930 → withdrawn

Angle valves for nominal pressure 25 · Operating pressures: I (W) 25; II (G) 20; III (H) 20 main dimensions

2nd edition of the standard

DIN 3326 edition 12.1930 → withdrawn

Angle valves for nominal pressure 40 · Operating pressures: I (W) 40; II (G) 32; III (H) 32 main dimensions

2nd edition of the standard

DIN 3327 edition 12.1930 → withdrawn

Angle valves · Housing for nominal pressure 6 · Operating pressures: I (W) 6; II (G) 5

2nd edition of the standard

DIN 3328 edition 12.1930 → withdrawn

Angle valves · Housing for nominal pressure 10 · Operating pressures: I (W) 10; II (G) 8

2nd edition of the standard

DIN 3329 edition 12.1930 → withdrawn

Angle valves · Housing for nominal pressure 16 · Operating pressures: I (W) 16; II (G) 13

2nd edition of the standard

DIN 3330 edition 12.1930 → withdrawn

Angle valves · Housing for nominal pressure 25 · Operating pressures: I (W) 25; II (G) 20; III (H) 20

2nd edition of the standard

DIN 3331 edition 12.1930 → withdrawn

Angle valves · Housing for nominal pressure 40 · Operating pressures: I (W) 40; II (G) 32; III (H) 32

2nd edition of the standard

DIN 3332 edition 9.1951 → withdrawn

Forged steel attachment valves · Nominal pressure 25 to 320

DIN 3332 edition 12.1943 → withdrawn

Forged steel attachment valves ND 25 to 320

DIN 3333 edition 9.1947 → withdrawn

Check valves made of steel · Cover blanks · Nominal pressure 25 to 320

DIN 3334 edition 10.1968 → withdrawn

Heating mixer with flange connection, ND 6 max. 110 ° C · Three-way mixer, four-way mixer, dimensions

DIN 3335 edition 10.1968 → withdrawn

Heating mixer with socket connection, ND 6 max. 110 ° C · Three-way mixer, four-way mixer, dimensions

DIN 3336 edition 10.1968 → withdrawn

Heating mixer with welding ends, ND 6 max. 110 ° C · Three-way mixer, four-way mixer, dimensions

DIN 3337 edition 9.1985 → replaced by DIN EN ISO 5211 edition 6.2001

Connections of rotary actuators for valves · Coupling dimensions, flange dimensions

DIN 3338 edition 12.1987 → current

Connections of rotary actuators to valves Coupling dimensions for claw couplings (form C)

DIN 3338 edition 6.1986 → replaced by edition 12.1987

Connections of rotary actuators to valves Coupling dimensions for claw couplings (form C)

DIN 3339 edition 1.1984 → withdrawn

Valves · Materials for housing parts

DIN 3340 edition 1.1944 → withdrawn

Expansion glands for nominal pressure 10, 16, 25 and 40

DIN 3341 edition 7.1989 → current

Plate valves for displacement compressors · Suction valves, pressure valves · Main dimensions, materials, installation

DIN 3348 · Edition 6.1946 → withdrawn

Continuous fire stoves made of sheet steel with electric coal heating

DIN 3349 Edition 3.1941 → withdrawn

Continuous fire stoves made of sheet steel with electric coal heating · Individual parts

DIN 3350 edition 12.1943 → withdrawn

Tapping clamps for cast iron and steel pipes · Production plan

DIN 3352 - Part 1 · Edition 5.1979 → withdrawn

Slider · General information

DIN 3352 - Part 2 Edition 8.1988 → replaced by DIN EN 1171 Edition 1.2003

Cast iron gate valve with metal sealing with internal spindle thread

DIN 3352 - Part 2 · Edition 8.1986 → replaced by Edition 8.1988

Cast iron gate valve with metal sealing with internal spindle thread

DIN 3352 - Part 2 · Edition 5.1979 → replaced by Edition 8.1986

Cast iron slide, metal-to-metal, with internal spindle thread

DIN 3352 - part 3 edition 8.1988 → replaced by DIN EN 1171 edition 1.2003

Cast iron gate valve with metal seal with external spindle thread

DIN 3352 - Part 3 · Edition 8.1986 → replaced by Edition 8.1988

Cast iron gate valve with metal seal with external spindle thread

DIN 3352 - Part 3 · Edition 11.1980 → replaced by Edition 8.1986

Cast iron slide, metal-to-metal seal, with external spindle thread

DIN 3352 - part 4 edition 1.1986 → replaced by DIN EN 1171 edition 1.2003

Cast iron gate valve, soft sealing, with internal spindle thread

DIN 3352 - part 4 edition 10.1980 → replaced by edition 1.1986

Cast iron slide, soft sealing, with internal spindle thread

DIN 3352 - Part 5 Edition 10.1980 → current

Steel gate valve with internal or external spindle thread, isomorphic series

DIN 3352 - Part 6 Edition 5.1979 → replaced by DIN EN 1984 Edition 3.2000

Slider made of unalloyed and low-alloy steel, with internal spindle thread

DIN 3352 - part 7 edition 5.1979 → replaced by DIN EN 1984 edition 3.2000

Slider made of unalloyed and low-alloy steel, with external spindle thread

DIN 3352 - Part 8 Edition 10.1980 → replaced by DIN EN 1984 Edition 3.2000

Slide made of tough steel, with external spindle thread

DIN 3352 - Part 9 · Edition 5.1979 → replaced by DIN EN 1984 Edition 3.2000

Slider made of heat-resistant steel

DIN 3352 - Part 10 Edition 5.1979 → replaced by DIN EN 1984 Edition 3.2000

Stainless steel gate valve

DIN 3352 - Part 11 edition 12.1981 → replaced by DIN EN 12288 edition 11.2003

Copper alloy gate valve with flange connection

DIN 3352 - Part 12 Edition 12.1981 → replaced by DIN EN 12288 Edition 11.2003

Copper alloy gate valve with socket connection

DIN 3352 - Part 13 Edition 10.1987 → replaced by DIN EN 1171 Edition 1.2003

Cast iron gate valve, soft-sealing, with internal spindle thread, with push-in socket on both sides

DIN 3354 - Part 1 · Edition 6.1982 → replaced by DIN EN 593 Edition 3.1998

Flaps · General information

DIN 3354 - Part 2 · Edition 6.1982 → replaced by DIN EN 593 Edition 3.1998

Valves · Butterfly valves, tight-fitting, soft-sealing, made of cast iron, with flanges

DIN 3354 - Part 3 · Edition 6.1982 → replaced by DIN EN 593 Edition 3.1998

Flaps · Butterfly valves, tight-fitting, soft-sealing, made of steel and cast steel, with flanges or butt weld ends

DIN 3354 - Part 4 Edition 6.1982 → replaced by DIN EN 593 Edition 3.1998

Flaps · Butterfly valves, tightly closing, made of steel and cast steel, metallic sealing, with flanges or welded ends

DIN 3356 - Part 1 · Edition 5.1982 → withdrawn

Valves · General information

DIN 3356 - Part 2 · Edition 5.1982 → replaced by DIN EN 13789 Edition 1.2003

Valves · Cast iron shut-off valves

DIN 3356 - part 3 edition 5.1982 → replaced by DIN EN 13709 edition 1.2003

Valves · Shut-off valves made of non-alloy steels

DIN 3356 - Part 4 Edition 5.1982 → replaced by DIN EN 13709 Edition 1.2003

Valves · Shut-off valves made of heat-resistant steels

DIN 3356 - Part 5 Edition 5.1982 → replaced by DIN EN 13709 Edition 1.2003

Valves · Stop valves made of stainless steels

DIN 3357 - part 1 edition 10.1989 → withdrawn

Ball valves · General information for ball valves made of metallic materials

DIN 3357 - Part 1 · Edition 8.1982 → replaced by Edition 10.1989

Ball valves · General information for ball valves made of metallic materials

DIN 3357 - Part 1 · Edition 12.1981 → replaced by Edition 8.1982

Ball valves · General information for ball valves made of metallic materials

DIN 3357 - Part 2 Edition 12.1981 → replaced by DIN EN 1983 Edition 7.2006

Ball valves made of steel with full passage

DIN 3357 - Part 3 · Edition 12.1981 → replaced by DIN EN 1983 Edition 7.2006

Steel ball valves with reduced bore

DIN 3357 - Part 4 Edition 12.1981 → withdrawn

Non-ferrous metal ball valves with full bore

DIN 3357 - Part 5 Edition 12.1981 → withdrawn

Non-ferrous metal ball valves with reduced passage

DIN 3357 - Part 6 Edition 12.1981 → withdrawn

Cast iron ball valves with full passage

DIN 3357 - Part 7 Edition 12.1981 → withdrawn

Cast iron ball valves with reduced passage

DIN 3358 · Edition 10.1982 → current

Connections of linear actuators to valves · Connection dimensions for flange connections

DIN 3359 edition 2.1984 → replaced by DIN EN 13397 edition 3.2002

Membrane shut-off valves made of metallic materials

DIN 3360 - Part 3 edition 12.1987 → replaced by DIN EN 484 and DIN EN 521 edition 12.1998

Gas appliances · Household cooking appliances for gaseous fuels · Liquid gas-powered cooking appliances for outdoor use

DIN 3360 - Part 3 · Edition 10.1973 → replaced by Edition 12.1987

Gas appliances · LPG-powered camping cooking appliances

DIN 3360 - Part 4 Edition 12.1985 → current

Gas appliances · Household cooking appliances for gaseous fuels · Stoves

DIN 3360 - part 5 edition 2.1987 → replaced by DIN EN 30 parts 1-3 edition 12.2003

Gas appliances · Household cooking appliances for gaseous fuels · Glass ceramic hobs

DIN 3360 - Part 6 Edition 12.1985 → replaced by DIN EN 30 Part 1-3 and Part 2-2 Edition 10.1999

Gas appliances · Household cooking appliances for gaseous fuels · Convection ovens

DIN 3360 - part 10 edition 8.1963 → withdrawn

Gas appliances · Household stoves, ovens and stoves for town gas · Additions and changes

DIN 3360 - Part 11 Edition 10.1991 → withdrawn

Household cooking appliances for gaseous fuels · Surface temperatures when the front is touched · German version HD 1003: 1990

DIN 3360 - Part 12 · Edition 10.2009 → current

Household cooking appliances for gaseous fuels · Usability

The standard contains requirements and tests for the usability of household gas cooking appliances according to DIN EN 30 and should be used for comparative tests for the usability of household gas cooking appliances.

DIN 3360 - Part 12 · Edition 10.2003 → replaced by Edition 10.2009

Household cooking appliances for gaseous fuels · Usability

DIN 3360 - Part 13 · Edition 9.2006 → current

Household cooking appliances for gaseous fuels · Hoods over the appliances

The standard contains requirements and tests for the installation of exhaust hoods above household gas cooking appliances in accordance with DIN EN 30.

DIN 3360 - Part 14 · Edition 1.2011 → current

Household cooking appliances for gaseous fuels · Materials in contact with food

The standard contains food hygiene requirements for the materials in household cooking appliances according to DIN EN 30 that come into contact with food.

DIN 3360 · Edition 6.1960 → withdrawn

Household stoves, ovens and stoves for town gas · Terms, construction, quality, performance and testing

DIN 3360 edition 3.1940 → withdrawn

Gas cookers, gas roasting ovens and gas stoves for the household · Regulations and guidelines for construction

DIN 3361 edition 3.1940 → withdrawn

Gas stoves and cooking parts for gas stoves for the household · Regulations for testing and assessment

DIN 3362 edition 8.1990 → withdrawn

Gas appliances with atmospheric burners · Terms, requirements, testing, labeling

DIN 3362 - Part 1 edition 2.1977 → replaced by DIN 3362 edition 8.1990

Gas appliances with burners without fans · Terms, requirements, labeling

DIN 3362 - part 2 edition 2.1977 → replaced by DIN 3362 edition 8.1990

Gas appliances with burners without fans · Test gases

DIN 3362 - part 3 edition 2.1977 → replaced by DIN 3362 edition 8.1990

Gas appliances with burners without fans · Test

DIN 3363 - Part 2 · Edition 1.1986 → withdrawn

Gas devices for commercial kitchen systems · Hot air circulation devices · Requirements and testing

DIN 3363 - Part 3 · Edition 7.1992 → current

Gas appliances for large kitchens · Glass ceramic hobs for stoves · Requirements and testing

DIN 3363 · Edition 7.1979 → replaced by DIN EN 203 Part 1 Edition 11.1992 and DIN EN 203 Part 2 Edition 3.1995

Gas appliances for large kitchen systems

DIN 3364 - Part 10 · Edition 2.1993 → withdrawn

Convection space heater for gaseous fuels with an atmospheric burner and pilot flame

DIN 3364 - Part 10 · Edition 5.1992 → replaced by Edition 2.1993

Convection space heater for gaseous fuels with an atmospheric burner and pilot flame

DIN 3364 - part 1 edition 4.1982 → replaced by DIN 3364 part 10 edition 5.1992

Gas appliances · Space heaters · Terms, requirements, labeling, testing

DIN 3364 - Part 2 · Edition 1.1988 → withdrawn

Gas appliances · Room heaters · Chimney-connected heating inserts with atmospheric burners

DIN 3364 - Part 10 Edition 3.1963 → withdrawn

Heating stoves for town gas · Stoves for propane / butane · Supplements for chimney-connected gas heating inserts

DIN 3364 - Part 10 Edition 11.1962 → withdrawn

Stoves for town gas and for propane / butane · Supplements for chimney-connected heating inserts

DIN 3364 - Part 11 Edition 7.1965 → withdrawn

Heating stoves for town gas · Supplements for heating stoves for natural gas, natural gas-air mixture, propane-air mixture, two-gas and all-gas heating stoves

DIN 3364 edition 3.1958 → withdrawn

Heating stoves for town gas · Terms, construction, quality, performance and testing

DIN 3364 edition 8.1934 → withdrawn

Gas stoves · Regulations for investigation and assessment

DIN 3365 - Part 10 Edition 3.1963 → withdrawn

Heating stoves for town gas, heating stoves for propane / butane · Supplements for chimney-connected gas heating inserts

DIN 3365 - Part 10 Edition 11.1962 → withdrawn

Stoves for town gas and for propane / butane · Supplements for chimney-connected heating inserts

DIN 3365 edition 8.1958 → withdrawn

Heating stoves for propane / butane · Terms, construction, quality, performance and testing

DIN 3366 - Part 10 Edition 8.1963 → withdrawn

Gas appliances · Household stoves, ovens and stoves for propane / butane · Additions and changes

DIN 3366 · Edition 6.1960 → withdrawn

Household stoves, ovens and stoves for propane / butane · Terms, construction, quality, performance and testing

DIN 3368 - part 2 edition 3.1989 → replaced by DIN EN 297 edition 11.1994 and DIN EN 625 edition 10.1995

Gas appliances · Circulation water heaters, combination water heaters · Requirements, testing

DIN 3368 - Part 2 · Edition 2.1980 → replaced by Edition 3.1989

Gas appliances · Combination water heater

DIN 3368 - part 3 edition 4.1979 → replaced by DIN 3368 part 2 edition 3.1989

Gas appliances · Circulation water heater with open and closed combustion chamber

DIN 3368 - Part 4 Edition 9.1982 → withdrawn

Gas appliances · Continuous water heater with automatic adjustment of the heat load · Requirements and tests

DIN 3368 - Part 5 Edition 7.1985 → replaced by DIN EN 483 Edition 6.2000

Gas appliances · Water heater with closed combustion chamber and mechanical combustion air supply or mechanical exhaust gas discharge · Requirements, testing

DIN 3368 - Part 10 · Edition 12.1962 → withdrawn

Continuous gas water heater for town gas · Supplements for natural gas

DIN 3368 · Edition 1.1956 → withdrawn

Continuous gas water heater for town gas · Terms, construction, quality, performance and testing

DIN 3368 · Edition 7.1940 → withdrawn

Continuous gas water heater · Regulations for testing and evaluation, with an appendix on minimum equipment requirements

DIN 3369 edition 3.1956 → withdrawn

Continuous gas water heater for town gas · Supplements for propane / butane · Terms, construction, quality, performance and testing

DIN 3370 edition 4.1980 → replaced by DIN EN 732 edition 4.1999

Gas appliances · Fridges and freezers

DIN 3370 edition 10.1970 → withdrawn

Domestic refrigerators · Gas equipment

DIN 3371 edition 10.1977 → replaced by DIN 30682 edition 7.1982

Gas appliances · Household washing machines and household washing kettles with burners without fans

DIN 3371 edition 2.1971 → withdrawn

Household washing machines and household washing kettles · Gas technical equipment

DIN 3372 - part 1 edition 1.1980 → replaced by DIN EN 419 part 1 edition 2.2001

Gas appliances · Radiant heaters with burners without fans, for space heating purposes

DIN 3372 - Part 1 · Edition 12.1971 → withdrawn

Gas appliances · Radiant heaters for space heating purposes

DIN 3372 - Part 2 · Edition 1.1980 → current

Gas appliances · Radiant heaters with burners without fan, for outdoor systems

DIN 3372 - Part 2 · Edition 5.1973 → withdrawn

Gas appliances · Radiant heaters for outdoor facilities

DIN 3372 - Part 3 · Edition 5.1980 → current

Gas appliances · Radiant heaters with burners without fan, for animal rearing

DIN 3372 - part 4 edition 4.1983 → current

Gas consumption devices · Radiant heaters with burners without fan, portable radiant heaters for space and open space heating

DIN 3372 - Part 6 Edition 12.1988 → withdrawn

Gas appliances · Radiant heater · Dark heater with burner with fan

DIN 3373 edition 8.1977 → withdrawn

Gas appliances · Solid fuel lighters

DIN 3373 Edition 7.1973 → withdrawn

Gas appliances · Solid fuel lighters

DIN 3373 edition 2.1962 → withdrawn

Gas-powered lighters for solid fuels · Terms, construction, quality, testing

DIN 3373 edition 9.1943 → withdrawn

Gas lighter · Conditions for examination and assessment

DIN 3374 edition 7.1985 → replaced by DIN EN 1359 edition 5.1999

Gas meters · Gas meters with deformable partitions · Diaphragm gas meters

DIN 3374 edition 4.1979 → replaced by edition 7.1985

Gas meters · Gas meters with deformable partitions · Diaphragm gas meters

DIN 3374 edition 9.1957 → withdrawn

Diaphragm gas meters · Terms, definitions

DIN 3374 edition 6.1947 → withdrawn

Diaphragm gas meters · Terms and definitions

DIN 3375 edition 9.1957 → withdrawn

Diaphragm gas meter · Components and testing

DIN 3375 edition 3.1940x → withdrawn

Diaphragm gas meters up to 20 l measuring space · Regulations for testing and assessments

Cross edition 8.1942

DIN 3376 - Part 1 · Edition 2.2005 → current

Gas meter screw connections · Two-piece connection · Technical rules of the DVGW

DIN 3376 - Part 1 · Edition 2.1993 → replaced by Edition 2.2005

Gas meter screw connections · Two-piece connection

DIN 3376 - Part 1 · Edition 2.1980 → replaced by Edition 2.1993

Gas meter screw connections · Two-piece connection

DIN 3376 - Part 1 · Edition 1.1973 → withdrawn

Gas meter screw connections · Two-piece connection

DIN 3376 - Part 2 · Edition 2.2005 → current

Gas meter screw connections · Single socket connection · Technical rules of the DVGW

DIN 3376 - Part 2 · Edition 2.1993 → replaced by Edition 2.2005

Gas meter screw connections · Single socket connection

DIN 3376 - Part 2 · Edition 10.1981 → replaced by Edition 2.1993

Gas meter screw connections · Single socket connection

DIN 3376 edition 12.1936 → withdrawn

Gas knife screw connections

DVGW 3240

DIN 3377 edition 2.1980 → replaced by DIN EN 89 edition 2.2001

Gas appliances · Storage water heater

DIN 3377 edition 8.1972 → withdrawn

Gas appliances · Storage water heater

DIN 3378 · Edition 4.1978 → current

Gas consumption devices for butcher and smoking plants

DIN 3379 Edition 8.1975 → current

Gas appliances · Grain dryers

DIN 3380 edition 12.1973 → withdrawn

Gas pressure regulators for inlet pressures up to 100 bar

DIN 3380 - Part 1 · Edition 6.1958 → withdrawn

Gas pressure regulators and their safety devices for town gas and long-distance gas · House pressure regulators

DIN 3380 - Part 2 Edition 10.1959 → withdrawn

Gas pressure regulators and their safety devices for town gas and remote gas pressure regulators (excluding house pressure regulators)

DIN 3380 - Part 3 · Edition 3.1959 → replaced by DIN 3381 Edition 6.1984

Gas pressure regulators and their safety devices for town gas and long-distance gas · Safety devices

DIN 3380 Edition 7.1939 → withdrawn

Dry gas pressure regulators for low pressure gas systems in buildings (back pressure up to 500 mm WS)

DIN 3381 edition 6.1984 → replaced by DIN EN 14382 edition 7.2005

Safety devices for gas supply systems with operating pressures up to 100 bar · Safety blow-off and safety shut-off devices

DIN 3382 edition 10.1976 → withdrawn

Gas appliances · Roasting machines

DIN 3383 - Part 1 · Edition 8.2013 → current

Connection of gas devices · Gas sockets, safety gas hose lines

DIN 3383 - Part 1 · Edition 6.1990 → replaced by Edition 8.2013

Gas hose lines and gas connection fittings · Safety gas hose lines, safety gas connection fittings

DIN 3383 - Part 1 · Edition 7.1981 → replaced by Edition 6.1990

Gas hoses and gas connection fittings · Safety gas hoses with connector · Safety gas connection fittings

DIN 3383 - Part 1 · Edition 9.1972 → withdrawn

Safety gas hoses and gas connection fittings · Safety gas hoses with connector

DIN 3383 - Part 2 · Edition 8.2013 → current

Connection of gas devices · Gas hose lines for permanent connection

DIN 3383 - part 2 edition 12.1996 → replaced by edition 8.2013

Gas hose lines and gas connection fittings · Gas hose lines for permanent connection

DIN 3383 - Part 2 · Edition 6.1990 → replaced by Edition 12.1996

Gas hose lines and gas connection fittings · Gas hose lines for permanent connection

DIN 3383 - Part 2 · Edition 8.1981 → replaced by Edition 6.1990

Gas hoses and gas connection fittings · Gas hoses for permanent connection

DIN 3383 - Part 2 Edition 9.1971 → withdrawn

Safety gas hoses and gas connection fittings · Safety gas hoses with threaded connection

DIN 3383 - Part 3 · Edition 11.1970 → withdrawn

Safety gas hoses and gas connection fittings · Safety gas connection fittings

DIN 3383 - Part 4 Edition 8.2013 → current

Connection of gas devices · Gas sockets and connectors for laboratory hoses

DIN 3383 - part 4 edition 12.1991 → replaced by edition 8.2013

Gas hose lines and gas connection fittings · Safety gas connection fittings and connectors for laboratory hoses and hose lines

DIN 3383 - Part 4 Edition 3.1982 → replaced by Edition 12.1991

Gas hoses and gas connection fittings · Safety gas connection fittings and fittings for laboratory hoses

DIN 3383 edition 3.1958 → withdrawn

Safety gas hoses made of rubber or plastics with reinforcement (for town gas up to 500 mm operating pressure) · Requirements

DIN 3383 Edition 10.1939 → withdrawn

Household rubber gas hoses

DIN 3384 edition 8.2007 → current

Gas hose lines made of stainless steel · Safety requirements, testing, marking

DIN 3384 · Edition 5.1998 → replaced by Edition 8.2007

Gas hose lines made of stainless steel · Safety requirements, testing, marking

DIN 3384 · Edition 5.1977 → replaced by Edition 5.1998

Stainless steel hoses for gas

DIN 3384 · Edition 10.1970 → withdrawn

Stainless steel hoses for gas

DIN 3385 Edition 10.1939 → withdrawn

Gas lights for outdoor lighting (low pressure gas)

DIN 3386 edition 10.2012 → current

Gas filter for an operating pressure up to and including 5 bar · Requirements and tests

DIN 3386 edition 10.1973 replaced by edition 10.2012

Filters in internal gas lines

DIN 3387 - Part 1 · Edition 11.2008 → current

Detachable pipe connections for metal gas pipes · Smooth pipe connections

DIN 3387 - Part 1 · Edition 1.1991 → replaced by Edition 11.2008

Detachable pipe connections for metal gas pipes · Smooth pipe connections

DIN 3387 - Part 2 Edition 12.1991 → current

Detachable pipe connections for metal gas lines · Flared pipe connections

DIN 3387 edition 7.1976 → replaced by DIN 3387 part 1 edition 1.1991

Connectors for metallic pipes, with smooth ends, for gas pipes

DIN 3388 - Part 1 · Edition 5.1978 → withdrawn

Exhaust flaps for gas fireplaces, thermally controlled

DIN 3388 - Part 1 · Edition 11.1970 → withdrawn

Exhaust flaps for gas fireplaces · thermally controlled

DIN 3388 - Part 2 Edition 9.1979 → current

Exhaust gas shut-off device for fireplaces for liquid or gaseous fuels, mechanically operated exhaust flaps · Safety requirements and testing

DIN 3388 - Part 2 · Edition 7.1976 → replaced by Edition 9.1979

Exhaust gas shut-off device for fireplaces for liquid or gaseous fuels, mechanically operated exhaust flaps · Safety requirements and testing

DIN 3388 - Part 2 Edition 11.1970 → withdrawn

Exhaust flaps for gas fireplaces · mechanically controlled

DIN 3388 - Part 4 Edition 12.1984 → current

Flue dampers for gas fireplaces, thermally controlled, device-specific · Requirements, testing, labeling

DIN 3389 edition 8.1984 → current

Ready-to-install insulating pieces for house connection lines in gas and water supply · Requirements and tests

DIN 3389 · Edition 5.1978 → replaced by Edition 8.1984

Insulating pieces for house connection lines in gas and water supply · Ready-to-install insulating pieces · Requirements and tests

DIN 3389 Edition 10.1973 → withdrawn

Insulating pieces for house connection lines in the gas and water supply · Ready-to-install insulating pieces

DIN 3390 edition 4.1937x → withdrawn

Fixed gas filling stations for town gas, sewage gas and other highly compressed gases Guidelines for construction (gas filling station guidelines)

Cross edition 10.1949

DIN 3391 edition 11.1996 → replaced by DIN EN 13611 edition 12.2000

General safety requirements for gas, safety and control equipment

DIN 3391 edition 11.1979 → replaced by edition 11.1996

Control devices and multiple control devices for gaseous fuels · General specifications

DIN 3391 edition 2.1971 → withdrawn

Actuators and multiple actuators for gas appliances · General specifications

DIN 3392 edition 2.1971 → withdrawn

Gas pressure regulators for gas appliances

DIN 3393 - part 1 edition 1.1973 → replaced by DIN EN 126 edition 8.1995

Multiple actuators for gas appliances · Multiple actuators

DIN 3393 - Part 2 Edition 11.1973 → withdrawn

Multiple actuators for gas consumption devices · Temperature regulators and limiting devices

DIN 3394 - Part 1 · Edition 5.2004 → replaced by DIN EN 16678 Edition 2.2016

Automatic control devices · Control devices for securing, blowing off and regulating pressures from 4 bar to 16 bar

DIN 3394 - Part 1 edition 11.1982 → replaced by DIN EN 161 edition 9.1991

Automatic control devices, valves · Safety shut-off devices, groups A, B and C · Safety requirements, testing

DIN 3394 - Part 1 edition 8.1973 → replaced by edition 11.1982

Automatic control devices, valves · Safety shut-off devices, groups A, B and C · Safety requirements, testing

DIN 3394 - part 2 edition 8.1973 → replaced by DIN EN 161 edition 9.1991

Self-actuators operated with auxiliary energy · Actuators with and without shut-off (zero termination), groups Rm and Ro, for control tasks

DIN 3394 - Part 3 Edition 1.2004 → replaced by DIN EN 16304 Edition 5.2013

Automatic control devices · Control devices for blowing off, class 0 for pressures up to 4 bar

DIN 3395 edition 12.1938 → withdrawn

Gas generating furnaces · Rules for guarantees and their proof

DVGW 3215

DIN 3396 edition 9.1957 → withdrawn

Above-ground high-pressure gas containers · Guidelines for construction, equipment and installation, testing, commissioning and operation

DIN 3396 edition 12.1933 → withdrawn

High pressure gas tanks for town gas · Guidelines for manufacture and operation

DVGW 3221

DIN 3397 edition 12.1969 → withdrawn

Low pressure gas cylinder · Basis of calculation

DIN 3398 - Part 1 edition 1.1992 → replaced by DIN EN 1854 edition 11.1997

Pressure switch for gas · Safety requirements, testing

DIN 3398 - Part 1 edition 11.1982 → replaced by edition 1.1992

Pressure monitor for gas in gas appliances · Safety requirements, testing

DIN 3398 - Part 1 · Edition 6.1973 → replaced by Edition 1.1992

Pressure monitor for gas in gas appliances · Safety requirements, testing

DIN 3398 - Part 2 · Edition 1.1992 → replaced by DIN EN 1854 Edition 11.1997

Pressure monitor for air, smoke and exhaust gases in combustion systems · Safety requirements, testing

DIN 3398 - Part 2 edition 11.1982 → replaced by edition 1.1992

Pressure monitor for air, smoke and exhaust gases in combustion systems

DIN 3398 - Part 3 Edition 11.1982 → withdrawn

Pressure monitor for gaseous substances · Safety requirements and testing

DIN 3398 - Part 4 Edition 10.1986 → withdrawn

Pressure switch for liquid fuels and heat transfer oils

DIN 3399 edition 8.1986 → withdrawn

Low gas safety devices · Safety requirements, testing

DIN 3399 edition 5.1973 → replaced by edition 8.1986

Gas shortage safety devices in gas consumption facilities

DIN 3400 edition 9.1973 → withdrawn

Fittings · Marking

DIN 3400 edition 7.1928 → withdrawn

Identification for gas, water and steam fittings

DIN 3401 · Edition 6.1966 → current

Drip oiler and oil glasses · Main dimensions

DIN 3401 edition 12.1923 → withdrawn

Oil glasses

DIN 3402 edition 3.1969 → withdrawn

Ball grease nipple

DIN 3402 edition 9.1962 → withdrawn

Ball grease nipple

DIN 3402 edition 1.1946 → withdrawn

Ball lubrication heads

DIN 3402 · Edition 5.1931 → withdrawn

Pressure lubrication heads

1st edition of the standard

DIN 3403 edition 1.1946 → withdrawn

Ball head lubrication heads

DIN 3404 edition 1.1988 → current

Button head grease nipples

DIN 3404 edition 3.1969 → replaced by edition 1.1988

Flat grease nipple

DIN 3404 edition 9.1962 → withdrawn

Flat grease nipple

DIN 3404 · Edition 6.1949 → withdrawn

Flat lubrication heads

DIN 3405 · Edition 5.1986 → current

Funnel-type grease nipple

DIN 3405 edition 8.1969 → replaced by edition 5.1986

Funnel-type grease nipple

DIN 3405 edition 9.1962 → withdrawn

Funnel-type grease nipple

DIN 3410 edition 12.1974 → current

Oiler · Main and connecting dimensions

DIN 3410 edition 4.1972 → withdrawn

Oiler · Main and connecting dimensions

DIN 3410 edition 9.1954 → withdrawn

Oiler · Connection and space requirements

DIN 3411 edition 10.1972 → current

Stauffer rifles · lightweight design

DIN 3411 edition 1.1959x → withdrawn

Stauffer rifles · lightweight design

Cross edition 7.1959

DIN 3411 edition 8.1942 → withdrawn

Stauffer bushes · light

DIN 3412 edition 10.1972 → current

Stauffer rifles · heavy construction

DIN 3412 edition 1.1959 → withdrawn

Stauffer rifles · heavy construction

DIN 3412 edition 7.1941 → withdrawn

Stauffer rifles heavy

DIN 3415 - Part 1 · Edition 6.1990 → current

Textile adhesive fasteners · Requirements

DIN 3415 - Part 2 · Edition 6.1990 → replaced by DIN EN 1414 edition 1.1997, DIN EN 12241, 12242 and 12243 edition 12.1999 and DIN EN 14959 edition 5.2006

Textile adhesive fasteners · Tests

DIN 3416 edition 5.1998 → replaced by DIN EN 16732 edition 5.2016

Zippers · Terms

DIN 3416 · Edition 5.1985 → replaced by Edition 5.1998

Zippers · Terms

DIN 3416 edition 7.1973 → replaced by edition 5.1985

Zippers · Terms, designations

DIN 3417 edition 5.1998 → replaced by DIN EN 16732 edition 5.2016

Metal zippers · Types, dimensions, materials

DIN 3417 edition 5.1985 → replaced by edition 5.1998

Metal zippers · Types, dimensions, materials

DIN 3417 edition 8.1975 → replaced by edition 5.1985

Metal zippers · Types, dimensions, materials

DIN 3418 edition 5.1998 → replaced by DIN EN 16732 edition 5.2016

Plastic zippers · Types, dimensions, materials

DIN 3418 edition 5.1985 → replaced by edition 5.1998

Plastic zippers · Types, dimensions, materials

DIN 3418 edition 8.1975 → replaced by edition 5.1985

Plastic zippers · Types, dimensions, materials

DIN 3419 - Part 1 edition 5.1998 → replaced by DIN EN 16732 edition 5.2016

Zippers · Technical delivery conditions

DIN 3419 - Part 1 · Edition 5.1985 → replaced by Edition 5.1998

Zippers · Technical delivery conditions

DIN 3419 - Part 2 Edition 5.1998 → replaced by DIN EN 16732 Edition 5.2016

Zippers · Labeling for the consumer

DIN 3419 - Part 2 · Edition 5.1985 → replaced by Edition 5.1998

Zippers · Labeling for the consumer

DIN 3419 Edition 8.1975 → replaced by DIN 3419 Part 1 Edition 5.1985

Zippers · Technical delivery conditions

DIN 3420 edition 9.1943 → withdrawn

Oil and grease lubrication pumps · Determination of the standard pressure head

DIN 3421 · Edition 6.1943 → withdrawn

Crank lengths and handle shapes for lubrication pumps

DIN 3422 · Edition 6.1943 → withdrawn

Rocker arm for lubrication pumps · Connection dimensions

DIN 3423 edition 9.1943 → withdrawn

Lubricating pumps · Delivery and change in delivery rate · Terms

DIN 3424 · Edition 6.1943 → withdrawn

Two- and three-hole mounting flanges for lubrication pumps · Connection dimensions

DIN 3430 · Edition 6.1986 → withdrawn

Fittings for gas installations · Angular shut-off ball valves

DIN 3431 edition 6.1986 → withdrawn

Fittings for gas installations · Connection ball valves in angled shape with screw connection

DIN 3432 edition 6.1986 → withdrawn

Fittings for gas installations · Connection ball valves in straight form with screw connection

DIN 3434 edition 6.2012 → current

Fittings for gas installations · Connection ball valves in straight form with screw connection · Sockets with conical connection

DIN 3435 · Edition 6.2012 → current

Fittings for gas installations · Angular connection ball valves with screw connection · Sockets with conical connection

DIN 3436 Edition 6.2012 → current

Fittings for gas installations · Grommets with cone seal and sealing ring

DIN 3437 edition 6.1990 → replaced by DIN EN 14141 edition 3.2004

Gas shut-off valves above PN 16 · Requirements and approval test

DIN 3440 edition 7.1984 → replaced by DIN EN 14597 edition 12.2005

Temperature regulating and limiting devices for heat generation systems · Safety requirements and testing

DIN 3440 edition 4.1976 → replaced by edition 7.1984

Temperature regulating and limiting devices for heat generation systems

DIN 3441 - Part 1 edition 5.1989 → replaced by DIN EN ISO 16135, 16136, 16137, 16138, 16139 and 21787 edition 6.2006

Valves made of plasticizer-free polyvinyl chloride (PVC-U) · Requirements and testing

DIN 3441 - Part 1 · Edition 7.1982 → replaced by Edition 5.1989

Valves made of plasticizer-free polyvinyl chloride (hard PVC) · Requirements and testing

DIN 3441 - Part 2 Edition 8.1984 → replaced by DIN EN ISO 16135 Edition 6.2006

Fittings made of plasticizer-free polyvinyl chloride (PVC-U) · Ball valves, dimensions

DIN 3441 - Part 2 · Edition 3.1977 → replaced by Edition 8.1984

Fittings made of hard PVC (hard polyvinyl chloride) · Ball valves, dimensions

DIN 3441 - Part 3 Edition 8.1984 → replaced by DIN EN ISO 16138 Edition 6.2006

Fittings made of plasticizer-free polyvinyl chloride (PVC-U) · Membrane fittings, dimensions

DIN 3441 - Part 3 · Edition 3.1977 → replaced by Edition 8.1984

Fittings made of hard PVC (hard polyvinyl chloride); Membrane fittings, dimensions

DIN 3441 - Part 4 Edition 6.1978 → replaced by DIN EN ISO 21787 Edition 6.2006

Fittings made of hard PVC (hard polyvinyl chloride) · Angle seat valves, dimensions

DIN 3441 - part 5 edition 1.1984 → replaced by DIN EN ISO 16136 edition 6.2006

Fittings made of plasticizer-free polyvinyl chloride (PVC-U) · Butterfly valves PN 6 and PN 10 for clamping · Dimensions

DIN 3441 - Part 6 Edition 3.1988 → replaced by DIN EN ISO 16139 Edition 6.2006

Fittings made of plasticizer-free polyvinyl chloride (PVC-U) · Gate valve with internal spindle thread · Dimensions

DIN 3442 - Part 1 edition 5.1987 → replaced by DIN EN ISO 16135, 16136, 16137, 16138, 16139 and 21787 edition 6.2006

Valves made of polypropylene (PP) · Requirements and testing

DIN 3442 - Part 1 · Edition 10.1980 → replaced by Edition 5.1987

Fittings made of PP (polypropylene) · Requirements and testing

DIN 3442 - Part 2 Edition 10.1980 → replaced by DIN EN ISO 16135 Edition 6.2006

Fittings made of PP (polypropylene) · Ball valves, dimensions

DIN 3442 - Part 3 Edition 7.1987 → replaced by DIN EN ISO 16138 Edition 6.2006

Fittings made of polypropylene (PP) · Membrane fittings, dimensions

DIN 3442 - Part 3 · Edition 8.1981 → replaced by Edition 7.1987

Fittings made of polypropylene (PP) · Membrane fittings, dimensions

DIN 3444 · Edition 5.2015 → current

Protective caps for pipeline parts with welded and threaded ends

The standard applies to protective caps, which are used to protect the thread from damage and the seal against the ingress of foreign bodies into the pipeline components.

DIN 3444 edition 10.1997 → replaced by edition 5.2015

Protective caps for pipeline parts with welded and threaded ends

DIN 3446 edition 8.1983 → withdrawn

Electric ignition devices for gas burners

DIN 3446 edition 6.1975 → replaced by edition 8.1983

Electric ignition devices for gas burners

DIN 3451 edition 10.1925 → withdrawn

Indicator taps

1st edition of the standard

DIN 3452 edition 7.1925x → withdrawn

Indicator screw plugs M 18 × 1.5 and 3/4 "

Cross edition 11.1951

DIN 3461 edition 11.1942 → withdrawn

Fittings socket cocks for nominal pressure 6

DIN 3462 edition 11.1942x → withdrawn

Fittings socket cocks for nominal pressure 10

Cross edition 6.1943

DIN 3465 edition 11.1942x → withdrawn

Flanged cocks for nominal pressure 10

Cross edition 6.1943

DIN 3470 edition 11.1943 → withdrawn

Packing cocks for nominal pressure 10

DIN 3470 edition 11.1942xxxx → withdrawn

Packing cocks for nominal pressure 10

Cross editions 6.1949 and 7.1957

DIN 3471 edition 11.1942xx → withdrawn

Three-way cocks, flanged cocks, three-way socket cocks for nominal pressure 10

Cross editions 6.1943 and 5.1957

DIN 3472 edition 11.1942xx → withdrawn

Three-way packing taps for nominal pressure 10

Cross editions 6.1944 and 9.1957

DIN 3475 edition 9.1993 → withdrawn

Fittings and fittings made of spheroidal graphite cast iron for raw and drinking water · Corrosion protection through internal enamelling · Quality requirements, tests

DIN 3476 edition 8.1996 → current

Fittings and fittings for raw and drinking water · Corrosion protection through EP inner coating made of powder paints (P) or liquid paints (F) · Requirements and tests

DIN 3481 edition 6.1983 → replaced by DIN 3489 edition 11.2001

Compressed air fittings · Male thread couplings, 42 mm claw spacing

DIN 3481 edition 3.1975 → replaced by edition 6.1983

Compressed air fittings · Male thread couplings, 42 mm cam spacing

DIN 3481 edition 1.1958 → withdrawn

Compressed air fittings · Male thread couplings, 42 mm cam spacing

DIN 3482 · Edition 6.1983 → replaced by DIN 3489 Edition 11.2001

Compressed air fittings · Internally threaded couplings, 42 mm claw spacing

DIN 3482 edition 3.1975 → replaced by edition 6.1983

Compressed air fittings · Internally threaded couplings, 42 mm cam spacing

DIN 3482 edition 1.1956 → withdrawn

Compressed air fittings · Internally threaded couplings, 42 mm cam spacing

DIN 3483 edition 6.1983 → replaced by DIN 3489 edition 11.2001

Compressed air fittings · Hose couplings, 42 mm claw spacing

DIN 3483 edition 12.1975 → replaced by edition 6.1983

Compressed air fittings · Hose couplings, 42 mm cam spacing

DIN 3483 edition 4.1958 → withdrawn

Compressed air fittings · Hose couplings 42 mm cam spacing

DIN 3483 edition 1.1956 → withdrawn

Compressed air fittings · Locking couplings, 42 mm cam spacing

DIN 3484 edition 6.1983 → replaced by DIN 3489 edition 11.2001

Compressed air fittings · Sealing coupling, 42 mm claw spacing

DIN 3484 · Edition 3.1975 → replaced by Edition 6.1983

Compressed air fittings · Sealing coupling, 42 mm cam spacing

DIN 3484 · Edition 1.1956 → withdrawn

Compressed air fittings · Locking couplings, 42 mm cam spacing

DIN 3485 edition 7.1984 → replaced by DIN 3489 edition 11.2001

Compressed air fittings · Sealing ring

DIN 3485 Edition 3.1975 → replaced by Edition 7.1984

Compressed air fittings · Sealing ring

DIN 3485 edition 1.1956 → withdrawn

Compressed air fittings · Seals

DIN 3486 edition 1.1956 → withdrawn

Compressed air fittings · Single cocks with coupling

DIN 3487 edition 1.1956 → withdrawn

Compressed air fittings · Double cocks with coupling

DIN 3488 edition 3.1958 → withdrawn

Compressed air fittings · plugs, plugs, springs, keys

DIN 3489 Edition 11.2001 → current

Compressed air couplings · Claw coupling, 42 mm claw spacing, without lock nut · External thread, internal thread, hose and locking coupling, rotatable claw coupling, sealing ring

See also

• List of DIN standards

swell

• DIN standard sheet directory 1926 (Beuth-Verlag, Berlin)
• DIN standard sheet directory 1929 (Beuth-Verlag, Berlin)
• DIN standard sheet directory 1931 (Beuth-Verlag, Berlin)
• DIN standard sheet directory 1950 (Beuth-Vertrieb GmbH, Berlin)
• DIN standard sheet directory 1953 (Beuth-Vertrieb GmbH, Berlin)
• DIN standard sheet directory 1956 (Beuth-Vertrieb GmbH, Berlin)
• DIN standard sheet directory 1963 (Beuth-Vertrieb GmbH, Berlin)
• DIN standard sheet directory 1974 (Beuth-Vertrieb GmbH, Berlin)
• DIN standards committees (all valid standards of the relevant standards committee)
• Beuth Verlag - Product search
• Beuth Verlag - Search for historical documents (registration required)