List of standards DIN 3500 to DIN 3999
The list of standards DIN 3500 to DIN 3999 lists all current standards and many historical standard editions in the number range 3500 to 3999.
DIN - German Institute for Standardization e. V. - is the national standardization organization of the Federal Republic of Germany based in Berlin .
Explanations of the list
- DIN-EN standards, DIN-EN-ISO standards, DIN-ISO standards, preliminary standards and draft standards are not listed in this list.
- The term “sheet” used in older standard editions has been uniformly transferred to “part”.
- The date of issue is indicated next to the standard number. Edition 9.1981 means that the standard was published in September 1981.
- Cross edition: If the date of issue is appended with an x, for example edition 9.1949x, the standard has only been changed slightly and remains valid.
- Unless otherwise noted, the withdrawal date of an old standard is the same as the issue date of the replacing standard (s).
- The entry "→ current" means that the standard is currently (as of June 2017) valid.
DIN 3500 · Edition 4.2012 → current
Shut-off valves for drinking water installations in properties and buildings Piston valve - PN 10
This product standard applies to straight-through piston valves that are installed as shut-off valves in drinking water installations in accordance with DIN 1988 and DIN EN 806. It specifies the dimensions of the piston valves and describes general requirements that piston valves must meet.
DIN 3500 edition 2.1990 → replaced by edition 4.2012
Shut-off valves for drinking water installations in properties and buildings Piston valve PN 10
DIN 3501 Edition 7.1950 → withdrawn
Water level indicator for steam boilers and containers · Connection dimensions, glass and mica dimensions
DIN 3501 edition 3.1944 → withdrawn
Water level indicator for steam boilers · Connection dimensions and glass dimensions
DIN 3502 Edition 10.2002 → current
Shut-off valves for drinking water installations in properties and buildings · Valves in straight form - upper part, inclined, PN 10 (inclined seat valve) · Technical rule of the DVGW
DIN 3502 edition 11.1985 → replaced by edition 10.2002
Shut-off valves for drinking water installations in properties and buildings · Valves in straight-through form; Upper part inclined PN 10 (angle seat valve)
DIN 3502 Edition 6.1960 → withdrawn
Small water fittings · Angle seat valves · with socket connection on both sides up to 10 kg / cm² operating pressure
DIN 3503 · Edition 6.1960 → withdrawn
Small water fittings · Angle seat valves · with socket connection on both sides and drainage or outlet valve up to 10 kg / cm² operating pressure
DIN 3504 · Edition 6.1960 → withdrawn
Small water fittings · valve upper parts · for angle seat valves up to 10 kg / cm² operating pressure
DIN 3507 edition 3.1964 → withdrawn
Water fittings for house installation · Straight-way valves · on the one hand with socket connection and on the other hand with screw connection with flat seal up to 10 kg / cm² operating pressure
DIN 3508 Edition 3.1964 → withdrawn
Water fittings for house installation · Straight-through valves · with soldered socket and lead pipe screw connection with flat seal up to 10 kg / cm² operating pressure
DIN 3509 · Edition 6.2010 → current
Fittings for drinking water systems in buildings · Drain valves (PN 10) · Requirements and tests
The standard does not apply to drain valves according to DIN EN 200.
DIN 3509 edition 12.1981 → replaced by edition 6.2010
Fittings for the water supply Drain valves, PN 10
DIN 3509 edition 3.1964 → withdrawn
Water fittings for house installation · Drain valves · with hose screw connection with flat seal up to 10 kg / cm² operating pressure
DIN 3510 U edition 7.1938x → withdrawn
Fittings and pipeline parts
Cross edition 7.1940, conversion standard
DIN 3511 U edition 6.1938x → withdrawn
Globe valves · Overview
Cross edition 7.1940, conversion standard
DIN 3512 edition 10.2002 → current
Shut-off valves for drinking water installations in properties and buildings · Valves in straight-through form - vertical upper part PN 10 (straight seat valve) · Technical rules of the DVGW
DIN 3512 edition 11.1985 → replaced by edition 10.2002
Shut-off valves for drinking water installations in properties and buildings · Valves in straight-through form; Upper part upright PN 10 (straight seat valve)
DIN 3512 - Part 1 edition 11.1981 → replaced by edition 11.1985
Shut-off valves for the water supply in buildings Straight-way valves Type QA according to DIN EN 94, PN 10
DIN 3512 edition 9.1958 → withdrawn
Small water fittings · Straight-way valves with socket connection on both sides · Up to 10 kg / cm² operating pressure
DIN 3512 U edition 6.1938x → withdrawn
Globe valves · Housing with double-sided socket connection
Cross edition 7.1940, conversion standard
DIN 3513 edition 2.1959 → withdrawn
Small water fittings · Straight-through valves with socket connection on both sides and drainage valve · Up to 10 kg / cm² operating pressure
DIN 3513 U edition 6.1938x → withdrawn
Straight-way valves · Housing with double-sided socket connection and drainage plugs on both sides
Cross edition 7.1940, conversion standard
DIN 3514 U edition 6.1938x → withdrawn
Globe valves · Housing with socket connection at the inlet and screw connection at the outlet
Cross edition 7.1940, conversion standard
DIN 3515 U · Edition 6.1938x → withdrawn
Straight-way valves · Housing with soldered socket at the inlet and screw connection at the outlet
Cross edition 7.1940, conversion standard
DIN 3516 U edition 6.1938x → withdrawn
Outlet valves · Overview
Cross edition 7.1940, conversion standard
DIN 3517 edition 9.1958 → withdrawn
Small water fittings · Drain valves · up to 10 kg / cm² operating pressure
DIN 3517 U edition 6.1938x → withdrawn
Drain valves · Drain valve bodies
Cross edition 7.1940, conversion standard
DIN 3518 U · Edition 6.1938x → withdrawn
Outlet valves · Outlet valve housing for hose screw connection
Cross edition 7.1940, conversion standard
DIN 3519 Edition 3.1964 → withdrawn
Water fittings for house installation · Upper valve parts · for straight and drain valves up to 10 kg / cm² operating pressure
DIN 3519 U · Edition 6.1938x → withdrawn
Straight and drain valves · Upper valve parts
Cross edition 7.1940, conversion standard
DIN 3520 · Edition 5.1960 → withdrawn
Small water fittings · Drain valve · Up to 10 kg / cm² operating pressure
DIN 3521 · Edition 6.1943 → withdrawn
Tap wrench medium
DIN 3522 · Edition 6.1943 → withdrawn
Hahn key · heavy
DIN 3523 · Edition 4.2001 → current
Fittings for drinking water installations · Extensions
DIN 3523 edition 9.1991 → replaced by edition 4.2001
Fittings for drinking water installation · Extensions
DIN 3523 · Edition 6.1983 → replaced by Edition 9.1991
Fittings for house installation · Extensions
DIN 3523 edition 1.1969 → replaced by edition 6.1983
Water fittings for house installation · Extensions
DIN 3525 edition 9.1967 → withdrawn
Gas fittings for house installation · Gas shut-off valves · Straight through with double-sided socket connection
DIN 3525 edition 1.1955 → withdrawn
Small gas fittings · Gas shut-off cocks with double-sided socket connection · Operating pressure up to 1000 mm WS · Main dimensions
Formerly gas taps
DIN 3525 U · Edition 6.1938x → withdrawn
Gas shut-off cocks with double-sided socket connection
Conversion standard
DIN 3526 edition 9.1967 → withdrawn
Gas fittings for house installation · Gas shut-off cocks · Straight-through form, with socket connection on the one hand and with screw connection on the other
DIN 3526 edition 1.1955 → withdrawn
Small gas fittings · Gas shut-off cocks with socket and screw connection with internal thread · Operating pressure up to 1000 mm WS · Main dimensions
Formerly gas taps
DIN 3526 U · Edition 6.1938x → withdrawn
Gas shut-off valves · with socket and screw connection with internal thread
Conversion standard
DIN 3527 edition 9.1967 → withdrawn
Gas fittings for house installation · Gas connection taps · Straight-through form, on the one hand with socket connection and on the other hand with screw connection
DIN 3527 edition 1.1955 → withdrawn
Small gas fittings · Device connection taps with socket and screw connection with internal thread · Operating pressure up to 500 mm WS · Main dimensions
Cooker connection taps
DIN 3527 U · Edition 6.1938x → withdrawn
Appliance connection taps (stove connection taps) · with socket and screw connection with internal thread
Conversion standard
DIN 3528 Edition 7.1986 → withdrawn
Fittings for gas installations · Grommets with sealing ring
DIN 3528 edition 11.1981 → replaced by edition 7.1986
Fittings for gas installations · Grommets with sealing ring
DIN 3528 edition 10.1965 → withdrawn
Gas fittings for house installation · Grommets (outlets) · with sealing ring
DIN 3528 edition 1.1955 → withdrawn
Small gas fittings · Outlets with internal thread
DIN 3528 U edition 4.1935x → withdrawn
Gas shut-off valves · Outlets with internal thread
Conversion standard
DIN 3529 edition 3.1982 → withdrawn
Fittings for gas installations · Shut-off cone cocks in straight-through form · Female thread connection
DIN 3529 edition 11.1981 → replaced by edition 3.1982
Fittings for gas installations · Shut-off cone cocks in straight-through form · Female thread connection
DIN 3529 edition 10.1973 → withdrawn
Gas fittings · straight-way gas shut-off cocks · closed construction with socket connection on both sides
DIN 3530 U edition 8.1936x → withdrawn
Fittings and fittings for sanitary purposes
Cross edition 7.1940, conversion standard
DIN 3531 edition 1.1955 → withdrawn
Small gas fittings · Gas cap corner cocks · Operating pressure up to 1000 mm WS · Main dimensions
DIN 3531 edition 1.1942 → withdrawn
Gas cap corner cocks
DIN 3532 edition 11.1981 → withdrawn
Fittings for gas installations · Shut-off cone cocks in angled shape
DIN 3532 edition 10.1973 → withdrawn
Gas fittings · corner gas shut-off cocks · with external thread and socket connection
DIN 3533 edition 11.1981 → withdrawn
Fittings for gas installations · Angular cone taps with screw connection
DIN 3533 edition 10.1973 → withdrawn
Gas fittings · corner gas shut-off cocks · with external thread and screw connection
DIN 3534 edition 3.1982 → withdrawn
Fittings for gas installations · Connection cone cocks in straight form with screw connection
DIN 3534 edition 11.1981 → replaced by edition 3.1982
Fittings for gas installations · Connection cone cocks in straight form with screw connection
DIN 3535 - Part 1 Edition 7.1991 → withdrawn
Seals for gas supply · Sealing materials made of elastomers for gas fittings in house installation · Requirements and testing
DIN 3535 - Part 1 · Edition 3.1988 → replaced by Edition 7.1991
Seals for gas supply · Sealing materials made of elastomers for gas fittings in house installation · Requirements and testing
DIN 3535 - Part 1 · Edition 2.1976 → replaced by Edition 3.1988
Seals for gas supply · Seals in gas fittings for house installation
DIN 3535 - Part 2 · Edition 4.1983 → replaced by DIN EN 279 Edition 10.1991 and DIN EN 291 Edition 4.1992
Seals for gas supply · Homogeneous elastomers for seals in household appliances · Safety requirements, testing
DIN 3535 - Part 3 · Edition 4.1986 → replaced by DIN EN 682 Edition 5.2002
Seals for gas supply · Sealing materials made of elastomers for gas supply and gas pipelines · Requirements and testing
DIN 3535 - Part 3 · Edition 4.1982 → replaced by Edition 4.1986
Seals for gas supply · Seals made of elastomers for gas supply and gas pipelines · Safety requirements and testing of materials
DIN 3535 - part 4 edition 8.1978 → replaced by DIN 3535 part 6 edition 4.1994
Seals for the gas supply · Seals made from It plates, in gas fittings, gas appliances and gas pipes
DIN 3535 - Part 5 Edition 12.1993 → current
Seals for the gas supply · Sealing materials made of rubber, cork and synthetic fibers for gas fittings and gas appliances · Safety requirements, testing
DIN 3535 - Part 5 · Edition 4.1983 → replaced by Edition 12.1993
Seals for gas supply · Sealing materials made of rubber-cork and rubber-cork-asbestos for gas fittings and gas devices · Safety requirements, testing
DIN 3535 - Part 6 · Edition 1.2011 → current
Seals for the gas supply · Flat seal materials based on fibers, graphite or polytetrafluoroethylene (PTFE) for gas fittings, gas devices and gas lines
DIN 3535 - Part 6 Edition 12.1999 → replaced by Edition 1.2011
Gaskets for gas supply · Flat gasket materials based on synthetic fibers, graphite or polytetrafluoroethylene (PTFE) for gas fittings, gas devices and gas lines
DIN 3535 - part 6 edition 4.1994 → replaced by edition 12.1999
Gaskets for gas supply · Flat gasket materials based on synthetic fibers or graphite for gas fittings, gas appliances and gas lines
DIN 3535 - part 6 edition 12.1993 → replaced by edition 4.1994
Gaskets for gas supply · Flat gasket materials based on synthetic fibers or graphite for gas fittings, gas appliances and gas lines
DIN 3535 - part 6 edition 12.1986 → replaced by edition 12.1993
Gaskets for gas supply · Flat gasket materials based on synthetic fibers or graphite for gas fittings, gas appliances and gas lines
DIN 3536 edition 1.1994 → current
Lubricants for gas fittings in house installation, in gas distribution and gas transport lines
DIN 3536 edition 11.1982 → replaced by edition 1.1994 and DIN EN 377 edition 7.1993
Lubricants for gas fittings and control devices · Requirements, testing
DIN 3536 - Part 1 Edition 11.1970 → withdrawn
Lubricants for gas fittings · Gas fittings in the gas supply
DIN 3536 - Part 2 Edition 11.1970 → withdrawn
Lubricants for gas fittings · Gas fittings in gas appliances
DIN 3537 - Part 1 · Edition 9.2011 → current
Gas shut-off valves up to 5 bar for domestic gas installation · Requirements and tests
DIN 3537 - Part 1 · Edition 6.1990 → replaced by Edition 9.2011 and DIN EN 331 Edition 4.1999
Gas shut-off valves up to PN 4 · Requirements and approval test
DIN 3537 - Part 1 · Edition 9.1981 → replaced by Edition 6.1990
Gas fittings · Requirements and approval test
DIN 3537 - part 2 edition 9.1981 → replaced by DIN 3537 part 1 edition 6.1990
Gas fittings · Requirements and approval test for plug valves
DIN 3537 - Part 3 Edition 1.1992 → replaced by DIN 12918 Part 2 Edition 9.2002
Gas shut-off valves up to PN 4 · Requirements and approval test for laboratory valves
DIN 3537 - Part 3 Edition 9.1981 → replaced by Edition 1.1992
Gas fittings · Requirements and approval test for laboratory fittings
DIN 3537 edition 10.1973 → replaced by DIN 3537 parts 1 and 2 edition 9.1981
Gas fittings · requirements; exam
DIN 3538 edition 7.1986 → withdrawn
Fittings for gas installations · Butterfly valves · Female thread connection
DIN 3538 edition 11.1981 → replaced by edition 7.1986
Fittings for gas installations · Butterfly valves · Female thread connection
DIN 3541 U edition 2.1939 → withdrawn
Beverage dispensing systems · Pipe dimensions, connection dimensions, threads
Conversion standard
DIN 3542 edition 10.2013 → current
Barrel sleeves and barrel connection parts · Connection dimensions
The barrel connection parts dealt with in the standard are used to connect line connection parts (tap heads) according to DIN 32677.
Correction of edition 3.2007
Correction of edition 3.2007
DIN 3542 edition 8.1998 → withdrawn
Barrel sleeves and barrel connection parts · Connection dimensions
DIN 3542 edition 10.1988 → replaced by edition 8.1998
Barrel sleeves and barrel connection parts · Connection dimensions
DIN 3542 edition 2.1974 → replaced by edition 10.1988
Barrel sleeves and barrel connection parts · Connection dimensions
DIN 3543 - Part 1 Edition 8.1984 → withdrawn
Tapping fittings made of metallic materials · Requirements, testing
DIN 3543 - Part 2 · Edition 5.1984 → withdrawn
Tapping fittings made of metallic materials with operational shut-off · Dimensions
DIN 3543 - Part 3 · Edition 7.1978 → withdrawn
Tapping fittings made of hard PVC (hard polyvinyl chloride), for plastic pipes · Dimensions
DIN 3543 - Part 4 Edition 8.1984 → withdrawn
Tapping fittings made of high density polyethylene (HDPE) for pipes made of HDPE · Dimensions
DIN 3543 - part 4 edition 7.1978 → replaced by edition 8.1984
Tapping fittings made of hard PE (hard polyethylene), for pipes made of hard PE · Dimensions
DIN 3544 - Part 1 · Edition 9.1985 → current
Fittings made of high density polyethylene (HDPE) · Requirements and testing of tapping fittings
DIN 3544 - Part 1 · Edition 7.1979 → replaced by Edition 9.1985
Fittings made of hard PE, type 1 and 2 (hard polyethylene) · Requirements and testing of tapping fittings
DIN 3545 edition 1.1980 → withdrawn
Steam trap · Requirements and testing
DIN 3546 - Part 1 · Edition 1.2011 → current
Shut-off valves for drinking water installations in properties and buildings · General requirements and tests for hand-operated piston valves in special designs, valves and diaphragm valves · Technical rules of the DVGW
DIN 3546 - Part 1 · Edition 10.2002 → replaced by Edition 1.2011
Shut-off valves for drinking water installations in properties and buildings · General requirements and tests for hand-operated piston valves, shut-off fittings for tapping fittings, slide valves and diaphragm fittings · Technical rules of the DVGW
DIN 3546 - Part 1 · Edition 2.1990 → replaced by Edition 10.2002
Shut-off valves for drinking water installations in properties and buildings · General requirements and tests
DIN 3546 - Part 1 edition 11.1985 → replaced by edition 10.2002
Shut-off valves for drinking water installations in properties and buildings · General requirements and testing
DIN 3547 - Part 1 Edition 6.1990 → replaced by DIN EN 13774 Edition 7.2003
Gas and water shut-off valves PN 4 to PN 16 · Requirements and approval test
DIN 3548 - Part 1 Edition 10.1993 → withdrawn
Condensate drain with flange connection
DIN 3548 - Part 1 · Edition 12.1981 → replaced by Edition 10.1993
Condensate drain with flange connection
DIN 3549 edition 12.1981 → withdrawn
Condensate drain · Delivery checks and evidence
DIN 3551 edition 2.1971 → withdrawn
Beverage fittings · Hose screw connections made of non-ferrous metal · Hose threaded connector, hose conical connector
DIN 3551 edition 11.1956 → withdrawn
Hose fittings for the beverage industry
DIN 3551 edition 4.1944 → withdrawn
Hose screw connections for beverage and food systems
DIN 3552 edition 12.1966 → withdrawn
Beverage fittings · Pipe unions made of non-ferrous metals · Threaded connectors, conical connectors, groove union nuts
DIN 3554 edition 2.1971 → withdrawn
Beverage fittings · toggle union nuts made of non-ferrous metal · for hose and pipe fittings
DIN 3554 edition 11.1956 → withdrawn
Union nuts and sealing rings for hose and pipe fittings for the beverage industry
DIN 3567 Edition 8.1963 → current
Pipe clamps for NW 20 to 500
DIN 3568 · Edition 6.2014 → current
Clamping plates for pipe suspensions on I- and IPB-beams, with CD-ROM
DIN 3568 edition 9.1977 → replaced by edition 6.2014
Clamping plates for pipe suspensions on I and IP steel
DIN 3568 · Edition 10.1962 → withdrawn
Clamping plates for pipe suspensions on I and IP steel
DIN 3570 edition 10.1968 → current
Round steel bracket for pipes from NW 20 to 500
DIN 3575 edition 8.1962 → withdrawn
Suspension anchor with welding end for pipe suspensions
DIN 3576 edition 12.1965 → withdrawn
Beam Claws · Construction sheet
DIN 3580 edition 2.1992 → current
Road caps and support plates · Requirements and tests · Technical rules of the DVGW
DIN 3580 edition 12.1976 → replaced by edition 2.1992
Road caps and support plates · Construction and testing principles
DIN 3581 edition 8.1990 → current
Gas pipes Street cap size 1
DIN 3581 edition 5.1973 → replaced by edition 8.1990
Long-distance gas pipelines · Street cap No. 1 for flue pipes and measuring contacts
DIN 3581 edition 5.1953 → withdrawn
Long-distance gas lines · Street cap no. 1 for flue pipes and measuring contacts
DIN 3582 Edition 8.1990 → current
Gas pipes Street cap size 2
DIN 3582 · Edition 5.1973 → replaced by Edition 8.1990
Gas pipelines · Street cap No. 2 for gate valves
DIN 3582 · Edition 5.1953 → withdrawn
Long-distance gas pipelines · Street cap No. 2 for gate valve
DIN 3583 Edition 8.1990 → current
Gas pipes Street cap size 3
DIN 3583 · Edition 5.1973 → replaced by Edition 8.1990
Long-distance gas lines · Street cap no. 3 for exhaust pipes, light version
DIN 3583 · Edition 5.1953 → withdrawn
Long-distance gas lines · Street cap No. 3 for exhaust pipes
DIN 3584 Edition 8.1990 → current
Gas pipes Street cap size 4
DIN 3584 · Edition 5.1973 → replaced by Edition 8.1990
Long-distance gas lines · Street cap no. 4 for exhaust pipes, heavy-duty design
DIN 3584 · Edition 5.1953 → withdrawn
Gas pipelines · Street cap no. 4 for emptying water pots
DIN 3585 Edition 8.1990 → current
Gas pipes Street cap size 5
DIN 3585 · Edition 5.1973 → replaced by Edition 8.1990
Long-distance gas pipelines · Street cap No. 5 for blow-off valves and condensate collectors
DIN 3585 · Edition 5.1953 → withdrawn
Long-distance gas lines · Street cap no. 5 for high pressure blow-off valves
DIN 3586 Edition 10.2003 → current
Thermally triggered shut-off devices for gas · Requirements and tests
Complete revision of DVGW-VP 301 edition 6.1984
DIN 3601 edition 11.1954 → withdrawn
Well drilling rigs · Drill diameter for drill pipes according to DIN 4918 and rivet drill pipes according to DIN 4928
DIN 3602 edition 2.1955 → withdrawn
Well drilling rigs · Overview, terms
DIN 3604 edition 11.1954 → withdrawn
Schappen · open, for drill pipes according to DIN 4918
DIN 3605 edition 11.1954 → withdrawn
Schappen · double-edged, for drill pipes according to DIN 4918
DIN 3606 edition 11.1954 → current
Pipe lifting caps for drill pipes according to DIN 4918
DIN 3620 edition 4.1987 → replaced by DIN EN 14396 edition 4.2004
Fixed ladders for small water supply structures
DIN 3620 edition 2.1978 → replaced by edition 4.1987
Fixed ladders for small water supply structures
DIN 3621 edition 10.1959 → withdrawn
Well extension · Flange elbow with sounding pipe socket
DIN 3622 edition 10.1959 → withdrawn
Well construction · Protective pipes for sounding pipes · Sealing rings
DIN 3623 edition 10.1959 → withdrawn
Well extension · Connection pieces for filter extension pipes for wells without suction pipe
DIN 3670 Edition 3.2000 → current
Disc handwheels
DIN 3670 edition 9.1971 → replaced by edition 3.2000
Disc handwheels made of light metal
DIN 3680 edition 4.1976 → replaced by DIN EN 26704 edition 11.1991
Steam Traps · Systems, Terms
DIN 3680 Edition 7.1962 → withdrawn
Steam Traps · Systems and Organs
DIN 3681 edition 7.1962 → withdrawn
Steam traps · Terms for operating data
DIN 3682 Edition 7.1962 → withdrawn
Condensate drain · Pressure levels, connection types, nominal widths, housing materials
DIN 3683 Edition 7.1962 → withdrawn
Steam trap · Identifying information
DIN 3684 edition 9.1977 → withdrawn
Condensate drain with screw connection and threaded nipple at the inlet and threaded socket at the outlet. Connection dimensions
DIN 3684 Edition 7.1962 → withdrawn
Condensate drain · with screw connection and threaded nipple at the inlet and threaded socket at the outlet · connection dimensions
DIN 3700 - Part 1 Edition 7.1925 → withdrawn
Manometer, vacuum meter, mano-vacuum meter · Attachment, treatment, operation
Specified as DIN 3700 in the standard sheet directory spring 1926 (without “Part 1”).
DIN 3701 Edition 7.1925 → withdrawn
Manometer, vacuum meter · Concentric scale, 60 and 70 mm nominal housing diameter
DIN 3702 Edition 7.1925 → withdrawn
Manometer, vacuum meter · Eccentric scale, 60 and 70 mm housing nominal diameter
DIN 3703 Edition 7.1925 → withdrawn
Pressure gauges, vacuum gauges, mano-vacuum gauges, concentric scale, 80 to 300 mm housing nominal diameter
DIN 3704 Edition 7.1925 → withdrawn
Diaphragm pressure gauges, diaphragm vacuum gauges, diaphragm spring pressure gauges · Concentric scale, 80 to 180 mm nominal housing diameter
DIN 3705 edition 7.1925 → withdrawn
Pressure gauges, vacuum gauges, mano-vacuum gauges · dials with concentric scale, construction sheet
DIN 3706 edition 7.1925 → withdrawn
Pressure gauge, vacuum gauge · dials with eccentric scale, construction sheet
DIN 3707 - Part 1 Edition 7.1925 → withdrawn
Manometer, vacuum meter · Concentric and eccentric scale, for nominal housing diameters of 60 and 70 mm, construction sheet
DIN 3707 - Part 2 Edition 7.1925 → withdrawn
Manometer, vacuum meter · Concentric scale, for nominal housing diameter from 80 to 300 mm, construction sheet
DIN 3707 - Part 3 · Edition 7.1925 → withdrawn
Mano-vacuum gauge · Concentric scale, for housing nominal diameters from 80 to 300 mm, construction sheet
DIN 3708 edition 7.1925 → replaced by DIN 3730 and DIN 3731 editions 10.1928
Manometer, vacuum meter, mano-vacuum meter · pointer · construction sheet
DIN 3709 edition 7.1925 → withdrawn
Pressure gauges, vacuum gauges, mano-vacuum gauges · socket connectors
DIN 3710 edition 7.1925 → withdrawn
Pressure gauges, vacuum gauges, mano-vacuum gauges · spigot connection pieces
DIN 3711 edition 7.1925 → withdrawn
Pressure gauges, vacuum gauges, mano-vacuum gauges · Connection nuts and soldering pipes
DIN 3712 edition 7.1925 → withdrawn
Manometer, mano-vacuum meter · Siphon
DIN 3713 Edition 7.1925 → withdrawn
Manometer cocks, manometer holder · tight
DIN 3714 edition 7.1925 → withdrawn
Manometer cocks, manometer holder · rotatable
DIN 3715 edition 8.1930 → withdrawn
Manometer cocks, manometer holder · R 1/4 "Use up to and including nominal pressure 10 · Manometer holder through fixed socket
DIN 3716 edition 8.1930 → withdrawn
Manometer cocks, manometer holder · R 1/2 "Use up to and including nominal pressure 10 · Manometer holder through fixed socket
DIN 3719 · Edition 8.1930 → withdrawn
Pressure gauge shut-off valve · Use up to and including nominal pressure 1250 · Pressure gauge connection through a fixed sleeve
DIN 3720 edition 8.1930 → withdrawn
Pressure gauge shut-off valve with venting · Use up to and including nominal pressure 1250 · Pressure gauge connection through fixed socket
DIN 3730 edition 10.1928 → withdrawn
Pressure gauges, vacuum gauges, mano-vacuum gauges · Pointer with socket for concentric scales
DIN 3731 edition 10.1928 → withdrawn
Manometer, vacuum meter, mano-vacuum meter · Pointer with socket for eccentric scales
DIN 3732 edition 8.1930 → withdrawn
Pressure gauges, vacuum gauges, mano-vacuum gauges · Mark pointer for concentric scales
DIN 3745 edition 2.1948 → withdrawn
Glass fiber insulating cloth
DIN 3750 edition 8.1957 → withdrawn
Seals · Designations
DIN 3752 · Edition 5.1973 → withdrawn
Asbestos cardboard, asbestos papers
DIN 3752 edition 12.1957 → withdrawn
Asbestos cardboard, asbestos papers
Pre-standard
DIN 3754 - Part 1 · Edition 5.1984 → withdrawn
Sealing sheets · It sheets · Dimensions, requirements, tests
DIN 3754 - Part 1 · Edition 4.1968 → replaced by Edition 5.1984
Sealing sheets · It sheets · Dimensions, requirements, tests
DIN 3754 - Part 2 · Edition 8.1970 → withdrawn
Gasket sheets · It sheets · Guidelines for use in gaskets
DIN 3754 edition 12.1957 → withdrawn
Sealing plates, It plates
Pre-standard
DIN 3760 edition 9.1996 → current
Radial shaft seals
DIN 3760 edition 4.1972 → replaced by edition 9.1996
Radial shaft seals
DIN 3760 - Selection 1 · Edition 5.1972 → withdrawn
Radial shaft seals · Selection of shapes and dimensions for metallurgical plants, rolling mills and cranes
DIN 3760 edition 10.1962 → withdrawn
Radial shaft seals with sleeve
DIN 3761 - Part 1 · Edition 1.1984 → current
Radial shaft seals for motor vehicles · Terms · Dimension letters, permissible deviations, radial force
DIN 3761 - Part 2 Edition 11.1983 → current
Radial shaft seals for motor vehicles · Application notes
DIN 3761 - Part 3 · Edition 1.1984 → current
Radial shaft seals for motor vehicles · Material requirements and testing
DIN 3761 - Part 4 Edition 1.1984 → current
Radial shaft seals for motor vehicles · Visible irregularities
DIN 3761 - Part 5 · Edition 1.1984 → current
Radial shaft seals for motor vehicles · Testing · Measuring conditions and measuring equipment
DIN 3761 - Part 6 Edition 1.1984 → current
Radial shaft seals for motor vehicles · Testing · Outside diameter measuring device
DIN 3761 - Part 7 · Edition 1.1984 → current
Radial shaft seals for motor vehicles · Testing · Tapered plug
DIN 3761 - Part 8 · Edition 1.1984 → current
Radial shaft seals for motor vehicles · Testing · Execution of the axial cuts
DIN 3761 - Part 9 · Edition 1.1984 → current
Radial shaft seals for motor vehicles · Testing · Radial force measuring device-digital
DIN 3761 - Part 10 · Edition 1.1984 → current
Radial shaft seals for motor vehicles · Functional test · Test bench and test conditions
DIN 3761 - Part 11 Edition 1.1984 → current
Radial shaft seals for motor vehicles · Functional test · Leakage assessment
DIN 3761 - Part 12 · Edition 1.1984 → current
Radial shaft seals for motor vehicles · Testing · Determination of the ball indentation hardness of elastomers (IRHD) · Micro hardness test
DIN 3761 - Part 13 · Edition 1.1984 → current
Radial shaft seals for motor vehicles · Testing of the vulcanization state of elastomers
DIN 3761 - Part 14 · Edition 1.1984 → current
Radial shaft seals for motor vehicles · Testing · Infrared spectroscopic analysis of elastomers
DIN 3761 - Part 15 · Edition 1.1984 → current
Radial shaft seals for motor vehicles · Testing · Determination of the cold behavior of elastomers · Differential thermal analysis
DIN 3770 · Edition 5.1986 → withdrawn
O-rings with special dimensional accuracy, made of elastomers · Not for new designs
DIN 3770 edition 10.1970 → replaced by edition 5.1986
O-rings with special dimensional accuracy, made of elastomers
DIN 3770 - Supplement · Edition 10.1970 → withdrawn
O-rings with special dimensional accuracy, made of elastomers · Construction information for installation
DIN 3771 - part 1 edition 12.1984 → replaced by DIN ISO 3601 part 1 edition 8.2010
Fluid technology · O-rings · Dimensions according to ISO 3601/1
DIN 3771 - part 2 edition 12.1984 → replaced by DIN ISO 3601 part 1 edition 8.2010
Fluid technology · O-rings · Testing, marking
DIN 3771 - Part 3 · Edition 12.1984 → current
Fluid technology · O-rings · Materials, area of application
DIN 3771 - part 4 edition 12.1984 → replaced by DIN ISO 3601 part 3 edition 8.2010
Fluid technology · O-rings · Deviations in shape and surface
DIN 3771 - part 5 edition 11.1993 → replaced by DIN ISO 3601 part 2 edition 8.2010
Fluid technology · O-rings · Calculation methods and dimensions of the installation spaces
DIN 3780 edition 9.1954 → current
Seals · Stuffing box diameter and corresponding packing widths · Construction sheet
DIN 3790 edition 4.1958 → withdrawn
Stainless steel cast fittings · Angle seat straight-through valves · with bracket attachment NW 10 to 32 for ND 10 to 25, NW 40 to 200 for ND 10
DIN 3791 edition 4.1958 → withdrawn
Stainless steel cast fittings, straight-way valves, angle valves, with bracket attachment NW 10 to 32 for ND 10 to 25, NW 40 to 200 for ND 10
DIN 3795 - Part 1 · Edition 12.1975 → withdrawn
Fittings for bulk goods wagons Fixed coupling GF for nominal width 100, nominal pressure 10
DIN 3795 - Part 2 Edition 12.1975 → withdrawn
Fittings for bulk goods wagons · Adapter GU-R4 AG (to threaded connector R4) for nominal width 100, nominal pressure 10
DIN 3795 - Part 3 Edition 12.1975 → withdrawn
Fittings for bulk goods wagons Blind coupling GB for nominal width 100, nominal pressure 10
DIN 3799 edition 8.1975 → current
Fittings for rail and road vehicle tanks · Transition piece from thread 5 1/2 inch to threaded connector · Nominal widths 80 and 100
DIN 3840 edition 9.1982 → replaced by DIN EN 12516 part 2 edition 10.2004
Valve body · Strength calculation against internal pressure
DIN 3841 - Part 1 · Edition 5.1990 → replaced by DIN EN 215 Edition 9.2004
Heating fittings · Radiator valves PN 10 · Dimensions, materials, design
DIN 3841 - Part 1 · Edition 7.1978 → replaced by Edition 5.1990
Heating fittings · Radiator valves, PN 10 · Dimensions, materials, design
DIN 3841 - part 2 edition 1.1982 → replaced by DIN EN 215 part 1 edition 3.1988
Heating fittings · Radiator valves PN 10 · Thermostatic radiator valves · Requirements and testing
DIN 3841 edition 6.1953 → withdrawn
Heating fittings · Regulating valves ND 10 · Straight-way valves, angle valves made of non-ferrous metal · Connection dimensions
DIN 3842 edition 3.1979 → current
Heating fittings · Radiator screw connections, PN 10 · Dimensions, materials, design
DIN 3842 edition 6.1953 → withdrawn
Heating fittings · Radiator screw connections ND 10 · made of non-ferrous metal · Connection dimensions
DIN 3843 · Edition 6.1953 → withdrawn
Heating fittings · Socket valve ND 10 with non-rising stem · Made of non-ferrous metal · Connection dimensions
DIN 3844 Edition 12.1981 → current
Heating fittings · 2-port valves PN 16 made of copper alloy with socket connection · Dimensions, materials
DIN 3844 · Edition 6.1953 → withdrawn
Heating fittings · in-line valves ND 10 · straight-way in-line valves · made of non-ferrous metal · connection dimensions
DIN 3845 edition 12.1981 → withdrawn
Heating fittings · Non-return valves PN 16 made of copper alloy with socket connection · Dimensions, materials
DIN 3845 · Edition 6.1953 → withdrawn
Heating fittings · Socket check valves ND 16 · made of non-ferrous metal · Connection dimensions
DIN 3846 edition 6.1953 → withdrawn
Heating fittings · Safety valves with weight load, made of non-ferrous metal · Connection dimensions
DIN 3847 edition 6.1953 → withdrawn
Heating fittings · Safety valves with spring loading · Made of non-ferrous metal · Connection dimensions
DIN 3848 edition 12.1981 → current
Heating fittings · Fill and drain cocks PN 12.5 · Dimensions, materials
DIN 3848 edition 1.1955 → withdrawn
Heating fittings · Filling and drainage taps made of non-ferrous metal · Main dimensions
DIN 3850 edition 12.1998 → withdrawn
Pipe fittings · Overview
DIN 3850 edition 5.1994 → replaced by edition 12.1998
Pipe fittings · Overview
DIN 3850 edition 2.1967 → replaced by edition 5.1994
Pipe fittings · Overview
DIN 3851 edition 10.1965 → withdrawn
Tube fittings · Tube outer diameter and thread
DIN 3851 edition 7.1953 → withdrawn
Pipe fittings for pipes without thread · Basic standard · Nominal widths, pipe outer diameter, metric threads
DIN 3851 edition 7.1951 → withdrawn
Pipe fittings for pipes without thread · Basic standard · Nominal widths, pipe outer diameter, metric threads
DIN 3852 - Part 1 · Edition 5.2014 → current
Screw-in spigots and screw-in holes for pipe screw connections, fittings and screw plugs · Construction dimensions for metric fine threads
DIN 3852 - Part 1 · Edition 5.2002 → replaced by Edition 5.2014
Screw-in spigot - screw-in holes for pipe screw connections, fittings · Locking screws with metric fine thread · Construction dimensions
DIN 3852 - Part 1 edition 2.1992 → replaced by edition 5.2002, DIN 3852 part 11 edition 5.1994, DIN EN ISO 9974 parts 1 and 3 edition 9.2000
Screw-in spigots, screw-in holes, for pipe screw connections, fittings · Locking screws with metric fine thread · Construction dimensions
DIN 3852 - Part 1 · Edition 9.1978 → replaced by Edition 2.1992
Screw-in spigot, screw-in holes, for pipe screw connections, fittings, screw plugs, with metric fine thread · Construction dimensions
DIN 3852 - Part 1 · Edition 5.1966 → replaced by Edition 9.1978
Screw-in spigot, screw-in holes for pipe screw connections, fittings, screw plugs, with metric fine thread · Construction dimensions
DIN 3852 - Part 1 Edition 8.1953 → withdrawn
Screw-in spigot · Screw-in holes for pipe screw connections, fittings, screw plugs with metric fine thread · Construction sheet
DIN 3852 - Part 2 · Edition 5.2014 → current
Screw-in spigots and screw-in holes for pipe screw connections, fittings and screw plugs · Construction dimensions for pipe threads
DIN 3852 - Part 2 edition 11.2000 → replaced by edition 5.2014
Screw-in spigots - screw-in holes for pipe screw connections, fittings · Locking screws with Whitworth pipe thread · Construction dimensions
DIN 3852 - part 2 edition 11.1991 → replaced by edition 11.2000
Screw-in trunnions, screw-in holes for screwed pipe connections, fittings · Screw plugs with Whitworth pipe thread · Construction dimensions
DIN 3852 - Part 2 · Edition 10.1964 → replaced by Edition 11.1991
Screw-in spigot, screw-in holes, for pipe screw connections, fittings, screw plugs, with Whitworth pipe thread · Construction dimensions
DIN 3852 - Part 2 Edition 8.1953x → withdrawn
Screw-in spigot · Screw-in holes for pipe screw connections, fittings, screw plugs with Whitworth pipe thread · Construction sheet
Cross edition 3.1961
DIN 3852 - part 3 edition 11.1991 → replaced by DIN EN ISO 6149 parts 1 to 3 edition 11.1996
Screw-in spigot · Screw-in holes for pipe screw connections, fittings, screw plugs with metric fine thread, Form F and Form W, sealing by O-ring · Construction dimensions
DIN 3852 - Part 11 · Edition 5.1994 → withdrawn
Screw-in spigot · Screw-in holes for pipe screw connections, fittings, screw plugs · Screw-in spigot form E · Construction dimensions
DIN 3852 - Part 21 Edition 9.2016 → current
Screw-in spigots and screw-in holes for pipe screw connections, fittings and screw plugs · Construction dimensions for pipe threads according to DIN EN ISO 228 Part 1 and O-ring seal
DIN 3853 edition 9.2001 → current
Solderless and soldered pipe screw connections · Threaded stems to union nuts · Design sheet
DIN 3853 edition 11.1982 → replaced by edition 9.2001 and DIN EN ISO 8434 part 1 edition 11.1997
Solderless and soldered pipe screw connections · Threaded stems to union nuts · Design sheet
DIN 3853 · Edition 6.1963 → withdrawn
Solderless and soldered pipe screw connections · Threaded stems to union nuts · Design sheet
DIN 3853 edition 9.1958 → withdrawn
Threaded pin for union nuts for solderless and soldered pipe screw connections · Construction sheet
DIN 3854 Edition 10.1995 → current
Solderless and soldered pipe screw connections · Threaded holes for union screws · Construction sheet
DIN 3854 edition 9.1958 → replaced by edition 10.1995
Solderless and soldered pipe screw connections · Threaded holes for union screws · Construction sheet
DIN 3855 edition 9.1966 → withdrawn
Pipe fittings · Connector lengths, wrench sizes
DIN 3858 Edition 8.2005 → current
Whitworth pipe thread for pipe screw connections · Cylindrical internal thread and tapered external thread · Dimensions
DIN 3858 edition 1.1988 → replaced by edition 8.2005
Whitworth pipe threads for pipe screw connections · Cylindrical internal thread and tapered external thread · Thread dimensions
DIN 3858 edition 8.1970 → replaced by edition 1.1988
Whitworth pipe thread · Cylindrical internal thread and tapered external thread for pipe fittings
DIN 3859 - Part 1 · Edition 9.2005 → current
Pipe fittings · Technical delivery conditions
The standard deals with pipe screw connections according to DIN 3850 or DIN EN ISO 8434 Part 1 and the corresponding connection side of the hose fittings according to DIN 20066 and DIN ISO 12151 Parts 2 and 3.
DIN 3859 - Part 1 · Edition 2.1998 → replaced by Edition 9.2005
Pipe fittings · Technical delivery conditions
DIN 3859 - Part 2 · Edition 7.1999 → current
Pipe fittings · Assembly instructions for solderless pipe fittings with cutting rings according to DIN 2353 and DIN EN ISO 8434-1
DIN 3859 - Part 2 · Edition 12.1995 → replaced by Edition 7.1999
Solderless pipe fittings with cutting rings according to DIN 2353 · Assembly instructions
DIN 3859 - Part 3 Edition 12.1995 → replaced by DIN EN ISO 19879 Edition 10.2005
Solderless pipe fittings with cutting rings according to DIN 2353 · Tests
DIN 3859 edition 3.1984 → replaced by edition 2.1998 and DIN EN ISO 8434 part 1 edition 11.1997
Pipe fittings · Technical delivery conditions
DIN 3859 edition 11.1970 → replaced by edition 3.1984
Pipe fittings · Technical delivery conditions
DIN 3861 edition 9.2016 → current
Solderless pipe fittings · Cutting rings · Types
The standard applies to cutting rings as they are required for solderless pipe screw connections with cutting ring according to DIN 2353 and supplements DIN EN ISO 8434 Part 1 Edition 2.2008.
DIN 3861 edition 11.2002 → replaced by edition 9.2016
Solderless pipe fittings · Cutting rings · Types
DIN 3861 edition 5.1994 → replaced by edition 11.2002 and DIN EN ISO 8434 part 1 edition 11.1997
Solderless pipe screw connections · Cutting rings · Type and bore shape W
DIN 3861 edition 11.1982 → replaced by edition 5.1994
Solderless pipe screw connections · Cutting rings · Type and bore shape W
DIN 3861 edition 9.1957 → withdrawn
Solderless pipe screw connections · Cutting rings · Type and bore shape W
DIN 3862 Edition 10.1995 → current
Solderless pipe screw connections · Double taper ring · Type and bore shape X
DIN 3862 edition 6.1963 → replaced by edition 10.1995
Solderless pipe screw connections · Double taper ring · Type and bore shape X
DIN 3862 edition 11.1954 → withdrawn
Solderless pipe screw connections · Double taper ring · Type and bore shape X
DIN 3863 Edition 8.2003 → current
Pipe fittings · Ball bushings · Type and bore shapes U and Y
DIN 3863 · Edition 10.1995 → replaced by Edition 8.2003
Pipe fittings · Ball bushings · Type and bore shapes U and Y
DIN 3863 edition 7.1966 → replaced by edition 10.1995
Pipe fittings · Ball bushings · Type and bore shapes U and Y
DIN 3864 edition 8.1961 → withdrawn
Pipe screw connections with collar bushing for hard soldering and butt welding · Flanged bushings · Type and bore form Z
DIN 3865 · Edition 4.2002 → withdrawn without replacement
Pipe screw connections · Sealing cone 24 ° with O-ring · For cutting ring connection according to DIN EN ISO 8434-1
DIN 3865 edition 5.1994 → replaced by edition 4.2002 and DIN EN ISO 8434 part 4 edition 9.2000
Pipe screw connections · Sealing cone 24 ° with O-ring, for bore form W according to DIN 3861
DIN 3866 · Edition 6.1990 → current
Refrigeration technology · Threaded stem, pipe flange 90 ° for solderless pipe screw connections, PN 40
DIN 3866 edition 2.1956 → replaced by edition 6.1990
Solderless pipe screw connections · Threaded pin with shoulder for flared pipe, pipe flange · Construction sheet
DIN 3867 · Edition 2.2012 → current
Solderless pipe fittings · Pressure rings for butt design
The standard applies to pressure rings that are used in compressed air brake systems and other compressed air systems in road vehicles.
DIN 3867 edition 8.2003 → replaced by edition 2.2012
Solderless pipe fittings · Pressure rings for butt design
DIN 3867 edition 11.1996 → replaced by edition 8.2003
Solderless pipe fittings · Pressure rings for butt design
DIN 3867 edition 11.1982 → replaced by edition 11.1996
Solderless pipe fittings with cutting ring · Pressure rings for butt design
DIN 3867 edition 11.1961 → withdrawn
Solderless pipe fittings with cutting ring · Pressure rings for butt design
DIN 3869 · Edition 5.1994 → current
Profile sealing rings
DIN 3870 edition 9.2001 → current
Solderless and soldered pipe fittings · Union nuts of the LL series
DIN 3870 · Edition 5.1985 → replaced by Edition 9.2001 and DIN EN ISO 8434 Part 1 Edition 11.1997
Solderless and soldered pipe fittings · Union nuts
DIN 3870 edition 1.1983 → replaced by edition 5.1985
Solderless and soldered pipe fittings · Union nuts
DIN 3870 edition 9.1965 → withdrawn
Solderless and soldered pipe fittings · Union nuts
DIN 3870 edition 8.1961 → withdrawn
Solderless and soldered pipe fittings · Union nuts
DIN 3870 edition 11.1954 → withdrawn
Solderless and soldered pipe fittings · Union nuts
DIN 3871 edition 10.1995 → current
Solderless and soldered pipe screw connections · Union screws
DIN 3871 edition 11.1982 → replaced by edition 10.1995
Solderless and soldered pipe screw connections · Union screws
DIN 3871 edition 11.1954 → withdrawn
Solderless and soldered pipe screw connections · Union screws
DIN 3872 edition 2.2012 → current
Solderless pipe fittings · Union nuts for butt design
The standard applies to union nuts that are used in compressed air brake systems and other compressed air systems in road vehicles.
DIN 3872 edition 8.2003 → replaced by edition 2.2012
Solderless pipe fittings · Union nuts for butt design
DIN 3872 edition 11.1996 → replaced by edition 8.2003
Solderless pipe fittings · Union nuts for butt design
DIN 3872 edition 6.1985 → replaced by edition 11.1996
Solderless pipe fittings with cutting ring · Union nuts for butt design
DIN 3872 edition 11.1982 → replaced by edition 6.1985
Solderless pipe fittings with cutting ring · Union nuts for butt design
DIN 3872 edition 11.1961 → withdrawn
Solderless pipe fittings with cutting ring · Union nuts for butt design
DIN 3900 · Edition 6.2001 → current
Solderless pipe fittings with cutting ring · Screw-in sockets of the LL series with tapered screw-in thread
DIN 3900 edition 4.1984 → replaced by edition 6.2001
Solderless pipe screw connections with cutting ring · Screw-in socket with tapered screw-in thread
DIN 3900 edition 10.1966 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · Screw-in socket with tapered screw-in thread for union nuts
DIN 3900 · Edition 6.1957 → withdrawn
Solderless and soldered pipe screw connections · Screw-in socket with tapered screw-in thread for union nuts
DIN 3901 edition 9.2001 → current
Solderless pipe screw connections with cutting ring · Screw-in socket with cylindrical screw-in thread for screw-in spigot form A
DIN 3901 edition 9.1987 → replaced by edition 9.2001 and DIN EN ISO 8434 part 1 edition 11.1997
Solderless pipe screw connections with cutting ring · Screw-in socket with cylindrical screw-in thread
DIN 3901 edition 4.1984 → replaced by edition 9.1987
Solderless pipe screw connections with cutting ring · Screw-in socket with cylindrical screw-in thread
DIN 3901 edition 2.1965 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · Screw-in socket with cylindrical screw-in thread for union nuts
DIN 3901 · Edition 6.1957 → withdrawn
Solderless and soldered pipe screw connections · Screw-in socket with cylindrical screw-in thread for union nuts
DIN 3902 edition 4.1984 → replaced by DIN EN ISO 8434 part 1 edition 11.1997
Solderless pipe fittings with cutting ring · Connection piece
DIN 3902 edition 6.1957 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · Connection piece for union nuts
DIN 3903 edition 4.2001 → current
Solderless pipe screw connections with cutting ring Elbow screw-in socket with tapered screw-in thread (not for new designs)
DIN 3903 edition 4.1984 → replaced by edition 4.2001
Solderless pipe screw connections with cutting ring · Elbow screw-in socket with tapered screw-in thread
DIN 3903 edition 10.1966 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · Elbow screw-in socket with tapered screw-in thread for union nuts
DIN 3903 edition 6.1957 → withdrawn
Solderless pipe screw connections with cutting ring · Elbow screw-in socket with tapered screw-in thread for union nuts
DIN 3904 edition 9.1987 → withdrawn
Solderless pipe screw connections with cutting ring · Elbow screw-in socket with cylindrical screw-in thread
DIN 3904 edition 4.1984 → replaced by edition 9.1987
Solderless pipe screw connections with cutting ring · Elbow screw-in socket with cylindrical screw-in thread
DIN 3904 edition 12.1965 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · Elbow screw-in socket with cylindrical screw-in thread for union nuts
DIN 3904 · Edition 6.1957 → withdrawn
Solderless pipe screw connections with cutting ring · Elbow screw-in socket with cylindrical screw-in thread for union nuts
DIN 3905 edition 4.1984 → replaced by DIN EN ISO 8434 part 1 edition 11.1997
Solderless pipe fittings with cutting ring · angled connection piece
DIN 3905 edition 12.1965 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · Angle connection piece for union nuts
DIN 3905 · Edition 6.1957 → withdrawn
Solderless pipe screw connections with cutting ring · Angle connection piece for union nuts
DIN 3906 edition 4.2001 → current
Solderless pipe screw connections with cutting ring T screw-in socket with tapered screw-in thread (not for new designs)
DIN 3906 edition 4.1984 → replaced by edition 4.2001
Solderless pipe screw connections with cutting ring · T screw socket with tapered screw-in thread
DIN 3906 edition 10.1966 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · T screw-in socket with tapered screw-in thread for union nuts
DIN 3906 Edition 6.1957 → withdrawn
Solderless pipe screw connections with cutting ring · T screw-in socket with tapered screw-in thread for union nuts
DIN 3907 edition 9.1987 → withdrawn
Solderless pipe screw connections with cutting ring · T screw-in socket with cylindrical screw-in thread
DIN 3907 edition 4.1984 → replaced by edition 9.1987
Solderless pipe screw connections with cutting ring · T screw-in socket with cylindrical screw-in thread
DIN 3907 edition 12.1965 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · T screw-in socket with cylindrical screw-in thread for union nuts
DIN 3907 edition 6.1957 → withdrawn
Solderless pipe screw connections with cutting ring · T screw-in socket with cylindrical screw-in thread for union nuts
DIN 3908 edition 4.1984 → replaced by DIN EN ISO 8434 part 1 edition 11.1997
Solderless pipe fittings with cutting ring · T-connector
DIN 3908 edition 12.1965 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · T-connector for union nuts
DIN 3908 · Edition 6.1957 → withdrawn
Solderless pipe screw connections with cutting ring · T-connector for union nuts
DIN 3909 edition 4.1984 → replaced by DIN EN ISO 8434 part 1 edition 11.1997
Solderless pipe fittings with cutting ring · Weld-on socket
DIN 3909 edition 12.1965 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · Weld-on socket for union nuts
DIN 3909 edition 6.1957 → withdrawn
Solderless pipe screw connections with cutting ring · Weld-on socket for union nuts
DIN 3910 edition 4.1984 → replaced by DIN EN ISO 8434 part 1 edition 11.1997
Solderless pipe fittings with cutting ring · Straight bulkhead connections
DIN 3910 edition 12.1965 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · Straight bulkhead connectors for union nuts
DIN 3910 edition 2.1965 → withdrawn
Solderless pipe screw connections with cutting ring · Straight bulkhead connectors for union nuts
DIN 3910 edition 3.1958 → withdrawn
Solderless pipe screw connections with cutting ring · straight bulkhead connector for union nuts
DIN 3911 edition 4.1984 → withdrawn
Solderless pipe screw connections with cutting ring · Angle bulkhead connector
DIN 3911 edition 12.1965 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · Elbow bulkhead connector for union nuts
DIN 3911 edition 6.1957 → withdrawn
Solderless pipe screw connections with cutting ring · Elbow bulkhead connector for union nuts
DIN 3912 edition 4.1984 → replaced by DIN EN ISO 8434 part 1 edition 11.1997
Solderless pipe fittings with cutting ring · welded bulkhead connector
DIN 3912 edition 12.1965 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · Welded bulkhead connector for union nuts
DIN 3912 · Edition 6.1957 → withdrawn
Solderless pipe screw connections with cutting ring · Welded bulkhead connector for union nuts
DIN 3913 · Edition 4.2001 → current
Solderless pipe screw connections with cutting ring L screw socket with tapered screw-in thread (not for new designs)
DIN 3913 edition 4.1984 → replaced by edition 4.2001
Solderless pipe fittings with cutting ring · L screw-in socket with tapered screw-in thread
DIN 3913 edition 10.1966 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · L screw socket with conical screw-in thread for union nuts
DIN 3914 edition 9.1987 → withdrawn
Solderless pipe screw connections with cutting ring · L screw-in socket with cylindrical screw-in thread
DIN 3914 edition 4.1984 → replaced by edition 9.1987
Solderless pipe screw connections with cutting ring · L screw-in socket with cylindrical screw-in thread
DIN 3914 edition 10.1966 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · L screw-in socket with cylindrical screw-in thread for union nuts
DIN 3915 edition 8.1961 → withdrawn
Tube fittings with flange bushing for brazing · Complete fittings and overview
DIN 3916 edition 8.1961 → withdrawn
Pipe fittings with collar bushing for butt welding · Complete fittings and overview
DIN 3917 edition 8.1961 → withdrawn
Pipe screw connections with flange socket for hard soldering and butt welding · Screw-in socket with cylindrical screw-in spigot and for union nuts
DIN 3918 edition 8.1961 → withdrawn
Pipe screw connections with collar bushing for hard soldering and butt welding · Connection pieces for union nuts
DIN 3919 · Edition 12.1965 → withdrawn
Pipe screw connections with flange socket for hard soldering and butt welding · Soldering and welding connection pieces for union nuts
DIN 3919 edition 8.1961 → withdrawn
Pipe screw connections with flange socket for hard soldering and butt welding · Soldering and welding connection pieces for union nuts
DIN 3920 · Edition 10.1966 → withdrawn
Pipe screw connections with collar bushing for hard soldering and butt welding · Elbow screw-in socket with tapered screw-in spigot and for union nuts
DIN 3920 · Edition 8.1961 → withdrawn
Pipe screw connections with collar bushing for hard soldering and butt welding · Elbow screw-in socket with tapered screw-in spigot and for union nuts
DIN 3921 edition 12.1965 → withdrawn
Pipe screw connections with flange socket for hard soldering and butt welding · Elbow screw-in socket with cylindrical screw-in spigot and for union nuts
DIN 3921 edition 8.1961 → withdrawn
Pipe screw connections with flange socket for hard soldering and butt welding · Elbow screw-in socket with cylindrical screw-in spigot and for union nuts
DIN 3922 edition 12.1965 → withdrawn
Pipe screw connections with collar bushing for hard soldering and butt welding · Angle connection piece for union nuts
DIN 3922 edition 8.1961 → withdrawn
Pipe screw connections with collar bushing for hard soldering and butt welding · Angle connection piece for union nuts
DIN 3923 Edition 10.1966 → withdrawn
Screwed pipe connections with collar bushing for hard soldering and butt welding · T-screw socket with tapered screw-in spigot and for union nuts
DIN 3923 edition 8.1961 → withdrawn
Screwed pipe connections with collar bushing for hard soldering and butt welding · T-screw socket with tapered screw-in spigot and for union nuts
DIN 3924 edition 12.1965 → withdrawn
Screwed pipe connections with collar bushing for hard soldering and butt welding · T-screw socket with cylindrical screw-in spigot and for union nuts
DIN 3924 edition 8.1961 → withdrawn
Screwed pipe connections with collar bushing for hard soldering and butt welding · T-screw socket with cylindrical screw-in spigot and for union nuts
DIN 3925 edition 12.1965 → withdrawn
Screwed pipe connections with collar bushing for hard soldering and butt welding · T-connector for union nuts
DIN 3925 edition 8.1961 → withdrawn
Screwed pipe connections with collar bushing for hard soldering and butt welding · T-connector for union nuts
DIN 3926 edition 8.1961 → withdrawn
Pipe screw connections with collar bushing for hard soldering and butt welding · Straight bulkhead connectors for union nuts
DIN 3930 edition 11.1961 → withdrawn
Solderless pipe fittings with cutting ring, butt joint design · Complete fittings and overview
DIN 3931 edition 11.1961 → withdrawn
Solderless pipe screw connections with cutting ring · Screw-in socket in butt design with cylindrical screw-in spigot and for union nuts
DIN 3932 edition 11.1961 → withdrawn
Solderless pipe fittings with cutting ring · Joints in butt design for union nuts
DIN 3933 edition 12.1965 → withdrawn
Solderless pipe screw connections with cutting ring · Elbow screw-in socket in butt joint design, with tapered screw-in spigot and for union nuts
DIN 3933 edition 11.1961 → withdrawn
Solderless pipe screw connections with cutting ring · Elbow screw-in socket in butt joint design, with tapered screw-in spigot and for union nuts
DIN 3934 edition 12.1965 → withdrawn
Solderless pipe screw connections with cutting ring · Elbow screw-in socket in butt version, with cylindrical screw-in spigot and for union nuts
DIN 3934 edition 11.1961 → withdrawn
Solderless pipe screw connections with cutting ring · Elbow screw-in socket in butt version, with cylindrical screw-in spigot and for union nuts
DIN 3935 edition 12.1965 → withdrawn
Solderless pipe screw connections with cutting ring · Angle connection piece in butt design, for union nuts
DIN 3935 edition 11.1961 → withdrawn
Solderless pipe screw connections with cutting ring · Angle connection piece in butt design, for union nuts
DIN 3936 edition 12.1965 → withdrawn
Solderless pipe screw connections with cutting ring · T screw-in socket in butt design, with tapered screw-in spigot and for union nuts
DIN 3936 edition 11.1961 → withdrawn
Solderless pipe screw connections with cutting ring · T screw-in socket in butt design, with tapered screw-in spigot and for union nuts
DIN 3937 edition 12.1965 → withdrawn
Solderless pipe screw connections with cutting ring · T screw-in socket in butt design, with cylindrical screw-in spigot and for union nuts
DIN 3937 edition 11.1961 → withdrawn
Solderless pipe screw connections with cutting ring · T screw-in socket in butt design, with cylindrical screw-in spigot and for union nuts
DIN 3938 edition 12.1965 → withdrawn
Solderless pipe screw connections with cutting ring · T connection piece in butt design, for union nuts
DIN 3938 edition 11.1961 → withdrawn
Solderless pipe screw connections with cutting ring · T connection piece in butt design, for union nuts
DIN 3940 edition 11.1961 → withdrawn
Solderless pipe screw connections with cutting ring · Straight bulkhead connection in butt design, for union nuts
DIN 3941 edition 12.1965 → withdrawn
Solderless pipe screw connections with cutting ring · Angle bulkhead connector in butt design, for union nuts
DIN 3941 edition 11.1961 → withdrawn
Solderless pipe screw connections with cutting ring · Angle bulkhead connector in butt design, for union nuts
DIN 3942 edition 4.2002 → current
Solderless pipe screw connections · Elbow connection with sealing cone 24 ° and O-ring · Adjustable direction, for cutting ring connection according to DIN EN ISO 8434-1
DIN 3942 edition 5.1994 → replaced by edition 4.2002 and DIN EN ISO 8434 part 4 edition 9.2000
Solderless pipe screw connections · Elbow connection with sealing cone 24 ° and O-ring · Directional adjustable for hole shape W according to DIN 3861
DIN 3943 · Edition 4.2002 → current
Solderless pipe fittings · T-piece with sealing cone 24 ° and O-ring · Directional adjustable, for cutting ring connection according to DIN EN ISO 8434-1
DIN 3943 · Edition 5.1994 → replaced by Edition 4.2002 and DIN EN ISO 8434 Part 4 Edition 9.2000
Solderless pipe fittings · T-connector with sealing cone 24 ° and O-ring · Directional adjustable for hole shape W according to DIN 3861
DIN 3944 · Edition 4.2002 → current
Solderless pipe fittings · L-connector with sealing cone 24 ° and O-ring · Directional adjustable, for cutting ring connection according to DIN EN ISO 8434-1
DIN 3944 edition 5.1994 → replaced by edition 4.2002 and DIN EN ISO 8434 part 4 edition 9.2000
Solderless pipe fittings · L-connector with sealing cone 24 ° and O-ring · Directional adjustable for bore form W according to DIN 3861
DIN 3945 · Edition 4.2002 → current
Solderless pipe screw connections · Screw-in socket with sealing cone 24 ° and O-ring · For cutting ring connection according to DIN EN ISO 8434-1
DIN 3945 edition 5.1994 → replaced by edition 4.2002 and DIN EN ISO 8434 part 4 edition 9.2000
Solderless pipe fittings · Screw-in socket with sealing cone 24 ° and O-ring · For bore form W according to DIN 3861
DIN 3946 · Edition 4.2002 → current
Solderless pipe fittings · Reducing socket with sealing cone 24 ° and O-ring · For cutting ring connection according to DIN EN ISO 8434-1
DIN 3946 edition 11.1996 → replaced by edition 4.2002 and DIN EN ISO 8434 part 4 edition 9.2000
Solderless pipe screw connections · Reducing socket with sealing cone 24 ° and O-ring · For bore form W according to DIN 3861
DIN 3949 edition 2.1998 → current
Solderless pipe fittings · Flare connection parts for the bore shape of the cutting ring connection according to DIN EN ISO 8434-1
DIN 3951 edition 4.1984 → replaced by DIN EN ISO 8434 part 1 edition 11.1997
Solderless pipe screw connections with cutting ring · Cross connector
DIN 3951 edition 8.1966 → replaced by edition 4.1984
Solderless pipe screw connections with cutting ring · Cross connector, for union nuts
DIN 3952 edition 4.1984 → replaced by DIN EN ISO 8434 part 1 edition 11.1997
Solderless pipe fittings with cutting ring · Elbow connector, directional adjustable
DIN 3952 edition 9.1969 → replaced by edition 4.1984
Solderless pipe fittings with cutting ring · Elbow connector, directional adjustable
DIN 3953 edition 4.1984 → replaced by DIN EN ISO 8434 part 1 edition 11.1997
Solderless pipe fittings with cutting ring · T-connector, directional adjustable
DIN 3953 edition 9.1969 → replaced by edition 4.1984
Solderless pipe fittings with cutting ring · T-connector, directional adjustable
DIN 3954 edition 4.1984 → replaced by DIN EN ISO 8434 part 1 edition 11.1997
Solderless pipe fittings with cutting ring · L-connector, directional adjustable
DIN 3954 edition 9.1969 → replaced by edition 4.1984
Solderless pipe fittings with cutting ring · L-connector, directional adjustable
DIN 3955 edition 9.2001 → current
Solderless pipe screw connections with cutting ring · Screw-in socket with shaft for spigot form A
DIN 3955 edition 9.1987 → replaced by edition 9.2001 and DIN EN ISO 8434 part 1 edition 11.1997
Solderless pipe fittings with cutting ring · Screw-in socket with shaft
DIN 3955 edition 4.1984 → replaced by edition 9.1987
Solderless pipe fittings with cutting ring · Screw-in socket with shaft
DIN 3960 edition 3.1987 → replaced by DIN 21772 edition 7.2012, DIN 21773 edition 8.2014 and DIN ISO 21771 edition 8.2014
Terms and parameters for spur gears (cylindrical gears) and spur gear pairs (cylinder gear pairs) with involute gearing
DIN 3960 edition 7.1980 → replaced by edition 3.1987
Terms and parameters for spur gears (cylindrical gears) and spur gear pairs (cylinder gear pairs) with involute gearing
DIN 3960 - supplement 1 edition 7.1980 → current
Terms and parameters for spur gears (cylinder gears) and spur gear pairs (cylinder gear pairs) with involute gearing · Compilation of the equations
DIN 3960 edition 10.1976 → replaced by edition 7.1980
Terms and parameters for spur gears (cylindrical gears) and spur gear pairs (cylinder gear pairs) with involute gearing
DIN 3960 - Supplement 1 Edition 10.1976 → replaced by Edition 7.1980
Terms and parameters for spur gears (cylinder gears) and spur gear pairs (cylinder gear pairs) with involute gearing · Compilation of the equations
DIN 3960 edition 8.1960 → replaced by edition 10.1976
Toothing · Determining variables and defects on spur gears · Basic terms
DIN 3960 edition 10.1953 → withdrawn
Toothing · Determining variables and defects on spur gears · Basic terms
DIN 3960 · Edition 6.1951 → withdrawn
Tooth fits · Determining variables and errors on spur gears · Basic terms
DIN 3961 edition 8.1978 → current
Tolerances for spur gear teeth · Basics
DIN 3961 edition 9.1953 → withdrawn
Gears · Tolerances for spur gear teeth according to DIN 867 · Explanations
DIN 3962 - Part 1 · Edition 8.1978 → current
Tolerances for spur gears · Tolerances for deviations from individual parameters
DIN 3962 - Part 1 edition 11.1952x → withdrawn
Gears · Tolerances for spur gear teeth according to DIN 867 · Permissible individual errors · Module up to 0.6
Cross edition 11.1957
DIN 3962 - Part 2 · Edition 8.1978 → current
Tolerances for spur gear teeth · Tolerances for tooth trace deviations
DIN 3962 - Part 2 Edition 11.1952x → withdrawn
Gear teeth · Tolerances for spur gear teeth according to DIN 867 · Permissible individual errors · Module over 0.6 to 1.6
Cross edition 4.1957
DIN 3962 - Part 3 · Edition 8.1978 → current
Tolerances for spur gears · Tolerances for pitch deviations
DIN 3962 - part 3 edition 11.1952x → withdrawn
Gears · Tolerances for spur gear teeth according to DIN 867 · Permissible single errors · Module over 1.6 to 4
Cross edition 7.1957
DIN 3962 - part 4 edition 11.1952x → withdrawn
Gear teeth Tolerances for spur gear teeth according to DIN 867 Permissible individual errors Module over 4 to 10
Cross edition 8.1957
DIN 3963 edition 8.1978 → current
Tolerances for spur gear teeth · Tolerances for rolling deviations
DIN 3963 edition 3.1953x → withdrawn
Gears · Tolerances for spur gear teeth according to DIN 867 · Permissible flank direction errors, permissible group errors, tooth thickness deviations
Cross edition 4.1957
DIN 3964 Edition 11.1980 → current
Center distance dimensions and center position tolerances of housings for spur gears
DIN 3964 edition 8.1978 → replaced by edition 11.1980
Center distance dimensions and center position tolerances of housings for spur gears
DIN 3964 edition 12.1954x → withdrawn
Toothing · Center-to-center distance dimensions
Cross edition 4.1956
DIN 3965 - Part 1 Edition 8.1986 → current
Tolerances for bevel gear teeth · Basics
DIN 3965 - Part 2 Edition 8.1986 → current
Tolerances for bevel gear teeth · Tolerances for deviations from individual parameters
DIN 3965 - Part 3 Edition 8.1986 → current
Tolerances for bevel gear teeth · Tolerances for rolling deviations
DIN 3965 - Part 4 Edition 8.1986 → current
Tolerances for bevel gear teeth · Tolerances for axis angle deviations and axis intersection deviations
DIN 3966 - Part 1 Edition 8.1978 → current
Specifications for gears in drawings · Specifications for spur gear (cylinder gear) involute gears
DIN 3966 - Part 2 Edition 8.1978 → current
Information for gears in drawings · Information for straight-bevel gear teeth
DIN 3966 - Part 3 · Edition 11.1980 → current
Information for gears in drawings · Information for worm and worm gear gears
DIN 3966 edition 3.1957x → withdrawn
Toothing · Information for spur gears in drawings
Cross edition 8.1962
DIN 3967 Edition 8.1978 → current
Gear fitting system · Backlash, tooth thickness tolerances, tooth thickness tolerances, basics
DIN 3967 edition 9.1953x → withdrawn
Gears · Tolerances for spur gear teeth according to DIN 867 · Permissible flank direction errors, permissible group errors, tooth width dimensions
Cross edition 7.1956
DIN 3968 Edition 9.1960 → current
Tolerances of single start hobs for spur gears with involute teeth
DIN 3969 - Part 1 · Edition 10.1991 → current
Surface roughness of tooth flanks · Roughness parameters · Surface classes
DIN 3970 · Edition 4.2010 → current
Master gears for testing cylindrical gears · Wheel bodies and toothing
DIN 3970 - Part 1 edition 11.1974 → replaced by DIN 3970 edition 4.2010
Master gears for testing spur gears · Gear bodies and toothing
DIN 3970 - Part 1 Edition 8.1967 → withdrawn
Master gears for testing spur gears · Gear bodies and toothing
DIN 3970 - Part 2 edition 11.1974 → replaced by DIN 3970 edition 4.2010
Master gears for testing spur gears · arbors
DIN 3970 - Part 2 · Edition 8.1967 → withdrawn
Master gears for testing spur gears · arbors
DIN 3971 Edition 7.1980 → current
Terms and determinants for bevel gears and bevel gear pairs
DIN 3971 · Edition 5.1956 → withdrawn
Toothing · Determining variables and errors on bevel gears · Basic terms
DIN 3972 Edition 2.1952 → current
Reference profiles of gear cutting tools for involute gears according to DIN 867
DIN 3973 - Part 1 · Edition 2.2017 → current
Permissible deviations for worm gear hobs · Fundamentals
The permissible deviations specified in the standard apply to single and multi-start hobs for the manufacture of worm gears. The standard covers hobs with modules up to 40 mm.
DIN 3973 - Part 2 · Edition 2.2017 → current
Permissible deviations for worm gear hobs · Table values
The permissible deviations specified in the standard apply to single and multi-start hobs for the manufacture of worm gears. The standard covers hobs with modules up to 40 mm.
DIN 3974 - Part 1 · Edition 11.1995 → current
Tolerances for worm gear teeth · Basics
DIN 3974 - Part 2 Edition 11.1995 → current
Tolerances for worm gear teeth · Tolerances for deviations from individual parameters
DIN 3975 - Part 1 Edition 7.2002 → current
Terms and parameters for cylindrical worm gears with axes crossing at right angles · worm and worm wheel
DIN 3975 - Part 2 · Edition 7.2002 → current
Terms and parameters for cylindrical worm gears with axes crossing at right angles · Deviations
DIN 3975 edition 10.1976 → replaced by DIN 3975 parts 1 and 2 edition 7.2002
Terms and determinants for cylindrical worm gear units with an axis angle of 90 °
DIN 3975 Edition 7.1960x → withdrawn
Toothing · Determining variables and errors in cylindrical worm drives · Basic terms
DIN 3976 Edition 11.1980 → withdrawn
Cylindrical worms · Dimensions, assignment of center distances and gear ratios in worm gear sets
DIN 3976 · Edition 4.1963 → withdrawn
Cylindrical worms · Dimensions, assignment of center distances and gear ratios in worm drives
DIN 3977 edition 2.1981 → current
Measuring piece diameter for the radial or diametrical test dimension of the tooth thickness on spur gears (cylindrical gears)
DIN 3978 edition 8.1976 → withdrawn
Helix angle for spur gear teeth
DIN 3979 Edition 7.1979 → current
Tooth damage on gear drives · Designation, characteristics, causes
DIN 3990 - Part 1 Edition 12.1987 → current
Load capacity calculation of cylindrical gears · Introduction and general influencing factors
DIN 3990 - Part 1 edition 12.1970 → replaced by DIN 3990 parts 1 to 4 edition 12.1987
Load capacity calculation of cylindrical and bevel gears · Fundamentals and calculation formulas
DIN 3990 - Part 2 Edition 12.1987 → current
Load capacity calculation of cylindrical gears · Calculation of the pitting load capacity
DIN 3990 - Part 2 edition 12.1970 → replaced by DIN 3990 parts 1 to 4 edition 12.1987
Load capacity calculation of cylindrical and bevel gears · Tooth form factor Y F
DIN 3990 - Part 3 Edition 12.1987 → current
Load capacity calculation of cylindrical gears · Calculation of the tooth root load capacity
DIN 3990 - Part 3 edition 12.1970 → replaced by DIN 3990 parts 1 to 4 edition 12.1987
Load capacity calculation of spur and bevel gears · load share factor Y ε , step overlap ε β
DIN 3990 - Part 4 Edition 12.1987 → current
Calculation of load capacity of spur gears · Calculation of the seizure load capacity
DIN 3990 - Part 5 Edition 12.1987 → current
Load capacity calculation of cylindrical gears · Fatigue strength values and material qualities
DIN 3990 - Part 5 edition 12.1970 → replaced by DIN 3990 parts 1 to 4 edition 12.1987
Load capacity calculation of cylindrical and bevel gears · Flank form factor Z H
DIN 3990 - Part 6 Edition 12.1994 → current
Calculation of load capacity of cylindrical gears · Calculation of fatigue strength
DIN 3990 - Part 6 · Edition 2.1994 → replaced by Edition 12.1994
Calculation of load capacity of cylindrical gears · Calculation of fatigue strength
DIN 3990 - part 6 edition 12.1970 → replaced by DIN 3990 parts 1 to 4 edition 12.1987
Load capacity calculation of cylindrical and bevel gears · Material factor Z M
DIN 3990 - part 7 edition 12.1970 → replaced by DIN 3990 parts 1 to 4 edition 12.1987
Load capacity calculation of spur and bevel gears · Pinion single mesh factor Z B , single wheel mesh factor Z D , profile overlap ε α
DIN 3990 - Part 8 edition 12.1970 → replaced by DIN 3990 parts 1 to 4 edition 12.1987
Load capacity calculation of cylindrical and bevel gears · Material factor Z M
DIN 3990 - part 10 edition 1.1973 → replaced by DIN 3990 parts 1 to 4 edition 12.1987
Load capacity calculation of cylindrical and bevel gears · Coverage factor Z ε
DIN 3990 - Part 11 Edition 2.1989 → current
Load capacity calculation of spur gears · Application standard for industrial gear units · Detail method
DIN 3990 - Part 21 · Edition 2.1989 → current
Load capacity calculation of spur gears · Application standard for high-speed gearboxes and gearboxes with similar requirements
DIN 3990 - Part 31 · Edition 7.1990 → current
Calculation of load capacity of spur gears · Application standard for marine gears
DIN 3990 - Part 41 · Edition 5.1990 → current
Load capacity calculation of spur gears · Application standard for vehicle transmissions
DIN 3990 - supplement 1 edition 12.1970 → withdrawn
Load capacity calculation of cylindrical and bevel gears · Notes on literature
DIN 3991 - Part 1 · Edition 9.1988 → current
Calculation of load capacity of bevel gears without offset · Introduction and general influencing factors
DIN 3991 - Part 2 · Edition 9.1988 → current
Calculation of the load capacity of bevel gears without offset · Calculation of the pitting load capacity
DIN 3991 - Part 3 Issue 9.1988 → current
Load capacity calculation of bevel gears without offset · Calculation of the tooth root load capacity
DIN 3991 - Part 4 Edition 9.1988 → current
Load capacity calculation of bevel gears without offset · Calculation of the seizure load capacity
DIN 3992 Edition 3.1964 → current
Profile shift for spur gears with external toothing
DIN 3993 - Part 1 Edition 8.1981 → current
Geometrical design of cylindrical internal gear pairs with involute teeth · Basic rules
DIN 3993 - Part 2 Edition 8.1981 → current
Geometrical design of cylindrical internal gear pairs with involute toothing · Diagrams showing geometrical limits for the pairing of ring gear and pinion
DIN 3993 - Part 3 Edition 8.1981 → current
Geometric design of cylindrical internal gear pairs with involute gearing · Diagrams for determining the profile shift factors
DIN 3993 - Part 4 Edition 8.1981 → current
Geometrical design of cylindrical internal gear pairs with involute toothing · Diagrams showing the limits for the pairing of ring gear and cutting wheel
DIN 3994 edition 8.1963 → withdrawn
Profile shift for straight-toothed spur gears with 05 toothing · Introduction
DIN 3995 - Part 1 · Edition 5.1967 → withdrawn
Straight-toothed external spur gears with 05 teeth · Center distances and operating pressure angle
DIN 3995 - Part 2 Edition 8.1963 → withdrawn
Straight-toothed external spur gears with 05 toothing · root diameter
DIN 3995 - Part 3 Edition 8.1963 → withdrawn
Straight-toothed external spur gears with 05 toothing · tip diameter
DIN 3995 - Part 4 Edition 8.1963 → withdrawn
Straight-toothed external spur gears with 05 toothing · Tooth width
DIN 3995 - Part 5 Edition 8.1963 → withdrawn
Straight-toothed external spur gears with 05-toothing · Inspection dimension M a
DIN 3995 - Part 6 Edition 8.1963 → withdrawn
Straight-toothed external spur gears with 05 toothing · Tooth thickness chord and tooth height above the chord
DIN 3995 - Part 7 Edition 8.1963 → withdrawn
Straight-toothed external spur gears with 05 toothing · Degree of overlap
DIN 3995 - Part 8 Edition 8.1963 → withdrawn
Straight-toothed external spur gears with 05 toothing · Sliding speeds at the tooth tip
DIN 3996 Edition 9.2012 → current
Load capacity calculation of cylindrical worm gears with axes crossing at right angles
DIN 3996 edition 9.1998 → replaced by edition 9.2012
Load capacity calculation of cylindrical worm gears with axis angle Σ = 90 °
DIN 3998 - supplement 1 edition 9.1976 → current
Designations on gears and gear pairs · Index
DIN 3998 - Part 1 · Edition 9.1976 → current
Designations on gears and gear pairs · General terms
DIN 3998 - Part 2 Edition 9.1976 → current
Designations on gears and gear pairs Spur gears and spur gear pairs (cylinder gears and cylinder gear pairs)
DIN 3998 - Part 3 Edition 9.1976 → current
Names of gears and gear pairs · Bevel gears and bevel gear pairs, hypoid gears and hypoid gear pairs
DIN 3998 - Part 4 Edition 9.1976 → current
Designations on gears and gear pairs · Worm gear sets
DIN 3999 edition 11.1974 → current
Abbreviations for gears
See also
swell
- DIN standard sheet directory 1926 (Beuth-Verlag, Berlin)
- DIN standard sheet directory 1929 (Beuth-Verlag, Berlin)
- DIN standard sheet directory 1931 (Beuth-Verlag, Berlin)
- DIN standard sheet directory 1950 (Beuth-Vertrieb GmbH, Berlin)
- DIN standard sheet directory 1953 (Beuth-Vertrieb GmbH, Berlin)
- DIN standard sheet directory 1956 (Beuth-Vertrieb GmbH, Berlin)
- DIN standard sheet directory 1963 (Beuth-Vertrieb GmbH, Berlin)
- DIN standard sheet directory 1974 (Beuth-Vertrieb GmbH, Berlin)
- DIN standards committees (all valid, as well as new and withdrawn standards of the respective standards committee)
- Beuth Verlag - Product search
- Beuth Verlag - Search for historical documents (registration required)