List of standards DIN 500 to DIN 999

Logo of the German Institute for Standardization

The list of standards DIN 500 to DIN 999 lists all current standards and many historical standard editions in the number range 500 to 999.

DIN - German Institute for Standardization e. V. - is the national standardization organization of the Federal Republic of Germany based in Berlin .

Explanations of the list

• DIN-EN standards, DIN-EN-ISO standards, DIN-ISO standards, preliminary standards and draft standards are not listed in this list.
• The term “sheet” used in older standard editions has been uniformly transferred to “part”.
• The date of issue is indicated next to the standard number. Edition 9.1981 means that the standard was published in September 1981.
• Cross edition: If the date of issue is appended with an x, for example edition 9.1949x, the standard has only been changed slightly and remains valid.
• Unless otherwise noted, the withdrawal date of an old standard is the same as the issue date of the replacing standard (s).
• The entry "→ current" means that the standard is currently (as of June 2017) valid.

DIN 500 edition 6.1929 → replaced by DIN 6880 edition 12.1943

Wedge steel, drawn · -10 fitting units according to DIN 773 for width and + 20 / + 10 fitting units according to DIN 773 for height

2nd edition of the standard

DIN 500 edition 4.1924 → replaced by edition 6.1929

Flat steel, drawn · Accuracy -10 units according to DIN 773 for width and + 20 / + 10 units according to DIN 773 for height

1st edition of the standard

DIN 501 edition 7.1937 → withdrawn 4 / 5.1949

Wedges · Overview

DIN 501 - Part 1 · Edition 4.1925 → withdrawn

Wedges · Overview

DIN 501 - Part 2 · Edition 4.1925 → withdrawn

Wedges · Overview

DIN 502 Edition 9.2004 → current

Plain bearing - flange bearing - fastening with two screws

The standard specifies the requirements for flange bearings for drive elements, fastening with two screws.

DIN 502 edition 7.1973 → replaced by edition 9.2004

Drive elements · Flanged bearings, fastening with 2 screws

DIN 502 edition 11.1946 → withdrawn

Flange bearing, fastening with two screws

DIN 502 edition 10.1922 → withdrawn

Flange bearing, fastening with two screws

DIN 503 edition 9.2004 → current

Plain bearing - flange bearing - fastening with four screws

The standard specifies the requirements for flange bearings for drive elements, fastening with four screws.

DIN 503 edition 7.1973 → replaced by edition 9.2004

Drive elements · Flanged bearings, fastening with 4 screws

DIN 503 edition 9.1946 → withdrawn

Flange bearing, fastening with four screws

DIN 503 edition 10.1922 → withdrawn

Flange bearing, fastening with four screws

DIN 504 edition 9.2004 → current

Plain bearings · eye bearings

The standard specifies the requirements for eye bearings.

DIN 504 edition 7.1973 → replaced by edition 9.2004

Drive elements · eye bearings

DIN 504 Edition 7.1928 → withdrawn

Eye bearing

DIN 505 edition 9.2004 → current

Plain bearings - cover bearings, bearing shells - bearing mounting with two screws

The standard specifies the requirements for cover bearings and bearing shells for drive elements, bearing mounting with two screws.

DIN 505 edition 7.1973 → replaced by edition 9.2004

Drive elements · Cover bearings, bearing shells, bearing mounting with 2 screws

DIN 505 edition 9.1946 → withdrawn

Lifting machines · Cover bearings · Fastened with two foot screws

DIN 505 edition 2.1932 → withdrawn

Cover bearing · Fastened with two foot screws · Connection dimensions

DIN 505 edition 1.1923 → withdrawn

Cover bearing · Fastened with two foot screws

DIN 506 edition 9.2004 → current

Plain bearings - cover bearings, bearing shells - bearing mounting with four screws

The standard specifies requirements for cover bearings and bearing shells for drive elements, bearing mountings with four screws.

DIN 506 edition 7.1973 → replaced by edition 9.2004

Drive elements · Cover bearings, bearing shells, bearing mounting with 4 screws

DIN 506 edition 9.1946 → withdrawn

Lifting machines · Cover bearings · Fastened with four foot screws

DIN 506 edition 1.1923 → withdrawn

Cover bearing · Fastened with four foot screws

DIN 507 Edition 7.1928 → withdrawn

Labeling of the normal thread gauges · Guidelines

DIN 508 Edition 6.2002 → current

Nuts for T-slots

Nuts for T-slots according to this standard are clamping elements that are used in T-slots according to DIN 650.

DIN 508 Edition 1.1997 → replaced by Edition 6.2002

Nuts for T-slots

DIN 508 edition 4.1991 → replaced by edition 1.1997

Nuts for T-slots

DIN 508 edition 2.1979 → replaced by edition 4.1991

Nuts for T-slots

DIN 508 Edition 10.1969 → withdrawn

T-nuts

DIN 508 edition 5.1956 → withdrawn

T-nuts

DIN 508 edition 1.1928 → withdrawn

T-nuts

DIN 509 edition 12.2006 → current

Technical drawings - undercuts - shapes, dimensions

This standard serves to standardize the inner and outer undercuts in turned parts and bores and to reduce the tools required for production.

DIN 509 edition 6.1998 → replaced by edition 12.2006

Undercuts - shapes, dimensions

This standard serves to standardize the inner and outer undercuts in turned parts and bores and to reduce the tools required for production.

DIN 509 edition 8.1966 → replaced by edition 6.1998

Undercut

DIN 509 edition 4.1956 → withdrawn

Undercut

DIN 510 edition 3.1923 → withdrawn

Machine jaw taps for Whitworth threads according to DIN 11

DIN 511 edition 3.1923 → withdrawn

Machine jaw taps for metric threads according to DIN 13 and 14

DIN 512 edition 3.1923 → withdrawn

Machine jaw taps for Whitworth pipe threads according to DIN 259 and 260

DIN 513 - Part 1 · Edition 4.1985 → current

Metric buttress threads · Thread profiles

The standard specifies the dimensions of the thread profiles of metric buttress threads.

DIN 513 - Part 2 · Edition 4.1985 → current

Metric buttress threads · Series of threads

The standard contains metric buttress threads with profiles according to DIN 513 Part 1.

DIN 513 - Part 3 · Edition 4.1985 → current

Metric buttress threads · Dimensions and tolerances

The same tolerance system is used for single-start metric buttress threads as for metric ISO fastening threads. The standard therefore contains extracts from DIN 13 Part 15 for threads with a pitch of up to 8 mm and additions to basic dimensions, screw-in lengths and tolerances for threads with pitches over 8 mm. Other preferred tolerance fields are recommended for buttress threads than for fastening threads. The same degrees of accuracy are specified for the pitch diameter as for metric trapezoidal threads.

DIN 513 edition 1.1927x → withdrawn

Buttress thread · single start

Cross edition 1949

DIN 514 - Part 1 Edition 1.1927xx → withdrawn

Buttress thread fine · single start · from 10 to 195 mm

Cross edition 4.1954

DIN 514 - Part 2 · Edition 1.1927x → withdrawn

Buttress thread fine · single start · from 200 to 640 mm

Cross edition 7.1947

DIN 515 edition 1.1927xx → withdrawn

Buttress thread, coarse

Cross editions 10.1947 and 7.1956

DIN 516 edition 12.1952 → withdrawn

Metric fine thread with pitch h = 1.5 mm, theoretical values

DIN 516 edition 9.1943 → withdrawn

Metric fine thread with pitch h 1.5 mm, theoretical values

DIN 516 · Edition 10.1923 → withdrawn

Metric fine thread 4 from 12 to 250 mm in diameter

DIN 517 edition 12.1952 → withdrawn

Metric fine thread with pitch h = 1 mm, theoretical values

DIN 517 edition 9.1943 → withdrawn

Metric fine thread with pitch h 1 mm, theoretical values

DIN 517 edition 10.1923 → withdrawn

Metric fine thread 5 from 9 mm to 82 mm in diameter

DIN 518 edition 12.1952 → withdrawn

Metric fine thread with pitch h = 0.75 mm, theoretical values

DIN 518 edition 9.1943 → withdrawn

Metric fine thread with pitch h 0.75 mm, theoretical values

DIN 518 Edition 10.1923 → withdrawn

Metric fine thread 6 from 6 mm to 80 mm in diameter

DIN 519 edition 12.1952 → withdrawn

Metric fine thread with pitch h = 0.5 mm, theoretical values

DIN 519 edition 9.1943 → withdrawn

Metric fine thread with pitch h 0.5 mm, theoretical values

DIN 519 edition 10.1923 → withdrawn

Metric fine thread 7 from 4.5 mm to 80 mm in diameter

DIN 520 · Edition 12.1952 → withdrawn

Metric fine thread with pitch h = 0.35 mm, theoretical values

DIN 520 · Edition 9.1943 → withdrawn

Metric fine thread with pitch h 0.35 mm, theoretical values

DIN 520 · Edition 10.1923 → withdrawn

Metric fine thread 8 from 3 mm to 50 mm in diameter

DIN 521 edition 12.1952 → withdrawn

Metric fine thread with pitch h = 0.25 mm and 0.2 mm, theoretical values

DIN 521 edition 9.1943 → withdrawn

Metric fine thread with pitch h 0.25 mm and 0.2 mm, theoretical values

DIN 521 edition 10.1923 → withdrawn

Metric fine thread 9 from 2.3 mm to 22 mm in diameter

DIN 522 edition 3.1990 → replaced by DIN EN ISO 4759 part 3 edition 9.2000

Discs made of metallic materials · Technical delivery conditions

DIN 522 edition 8.1980 → replaced by edition 3.1990

Washers · Technical delivery conditions

DIN 522 edition 4.1968 → withdrawn

Washers and lock washers · Permissible deviations

DIN 522 edition 1.1954 → withdrawn

Washers and lock washers · Permissible deviations

DIN 522 edition 10.1944 → withdrawn

Washers and lock washers · permissible deviations

DIN 523 Edition 7.1974 → current

Rotary mandrels · Workpiece holding mandrels

DIN 523 edition 9.1953 → withdrawn

Clamping tools · mandrels

DIN 523 edition 3.1935 → withdrawn

Rotary mandrels

DIN 524 edition 8.1922 → withdrawn

Normal temperature

DIN 525 edition 11.2009 → current

Welding ends

The standard contains the dimensional specifications and technical delivery conditions for welding and specifies their designation.

DIN 525 edition 9.1986 → replaced by edition 11.2009

Welding ends

DIN 525 edition 11.1970 → replaced by edition 9.1986

Welding ends

DIN 525 - Part 1 · Edition 6.1953 → withdrawn

Welding ends, without nut · with hexagon nut · M6 to M48

DIN 525 - Part 1 · Edition 1.1941 → withdrawn

Welding ends · without nut or with hexagon nut · M6 to M48

DIN 525 - Part 2 Edition 10.1955 → withdrawn

Welding ends, without nut with hexagon nut 1/4 "to 2"

DIN 525 - Part 2 Edition 10.1937x → withdrawn

Welding ends with nut 7/16 "to 2"

DIN 525 edition 12.1929 → withdrawn

Welding ends

DIN 526 edition 5.1973 → 5.2003 withdrawn without replacement

Locking cups for countersunk cheese head screws according to DIN 84

DIN 526 · Edition 6.1947 → withdrawn

Locking cups for countersunk cheese head screws according to DIN 84

DIN 529 edition 9.2010 → current

Stone screws

The standard contains the dimensional specifications and technical delivery conditions for stone screws and specifies their designation.

DIN 529 edition 12.1986 → replaced by edition 9.2010

Stone screws

DIN 529 edition 12.1972 → replaced by edition 12.1986

Stone screws

DIN 529 - Part 1 · Edition 5.1960 → withdrawn

Stone screws M8 to M64, M72 × 6

DIN 529 - Part 1 · Edition 7.1953 → withdrawn

Stone screws · Metric thread

DIN 529 - Part 1 · Edition 1.1942 → withdrawn

Stone screws M8 to M48

DIN 529 - Part 2 · Edition 8.1954 → withdrawn

Stone screws · 5/16 "to 2"

DIN 529 - Part 2 Edition 10.1937x → withdrawn

Stone screws 1/2 "to 2"

DIN 529 edition 4.1928 → withdrawn

Stone screws

DIN 532 edition 11.1929x → withdrawn and partly replaced by DIN 931 part 2 edition 4.1942

Raw and bare hexagon bolts · over 52 mm or 2 "· construction sheet

1st edition of the standard; Cross edition 2.1942

The replacement by DIN 931 part 2 edition 4.1942 concerns hexagon bolts with metric thread.

DIN 533 - Part 1 · Edition 9.1959 → withdrawn

Castle nuts (raw) M6 to M33

DIN 533 - Part 1 · Edition 1.1941 → withdrawn

Castle nuts · M6 to M33, design g

DIN 533 - Part 2 Edition 9.1959 → withdrawn

1/2 "to 1 1/4" (raw) castle nuts

DIN 533 - Part 2 · Edition 8.1954 → withdrawn

Castle nuts 1/4 "to 1 1/4"

DIN 533 - Part 2 · Edition 4.1934x → withdrawn

Castle nuts · without neck, 7/16 "to 1 1/4", design g

DIN 533 edition 4.1934 → withdrawn

Raw castle nuts without neck · Metric thread from M 6 to M 10, Whitworth thread 1/4 "to 1 1/4"

DIN 534 - Part 1 · Edition 1.1941x → withdrawn

(Semi-bright) castle nuts M 12 to M 52 Version mg

Cross edition 12.1953

DIN 534 - Part 2 · Edition 8.1954 → withdrawn

(Semi-bright) castle nuts · 1/2 "to 2" · Version mg

DIN 534 - Part 2 · Edition 4.1934x → withdrawn

Castle nuts 1/2 "to 2", style g

DIN 536 - Part 1 · Edition 9.1991 → current

Crane rails · Dimensions, static values, steel types for crane rails with foot flange form A

This standard contains technical delivery conditions for crane rails. Dimensions, static values, limit dimensions and shape tolerances of the various profiles as well as the properties of the steel types are specified.

DIN 536 - Part 1 · Edition 12.1974 → replaced by Edition 9.1991

Crane rails, form A (with foot flange) · Dimensions, static values, steel types

DIN 536 - Part 1 · Edition 4.1959 → withdrawn

Crane rails Form A (with foot flange)

DIN 536 - Part 2 · Edition 12.1974 → current

Crane rails · Form F (flat) · Dimensions, static values, steel types

DIN 536 - Part 2 Edition 11.1962 → withdrawn

Crane rails Form F (flat)

DIN 536 edition 5.1941 → withdrawn

Crane rails

DIN 537 edition 12.1922 → withdrawn 6 / 7.1949

Shaft diameter for lifting machines

DIN 538 · Edition 5.1953 → withdrawn

LNA socket cover

DIN 538 Edition 4.1923 → withdrawn

Drain pipe socket cover for NA and LNA pipes

DIN 539 - Part 1 · Edition 4.1998 → withdrawn

Cleaning screws for odor traps on drainage objects · Brass cleaning screws

The standard describes cleaning screws made of brass for odor traps on drainage objects.

DIN 539 - Part 1 edition 11.1974 → replaced by edition 4.1998

Cleaning screw for drainage objects made of CuZn alloy

DIN 539 - Part 1 · Edition 7.1972 → withdrawn

Cleaning screw for drainage objects made of CuZn alloy

DIN 539 - Part 2 · Edition 4.1998 → withdrawn

Cleaning screws for odor traps of drainage objects Cleaning screws made of polypropylene (PP)

The standard describes cleaning screws made of PP for odor traps of drainage objects.

DIN 539 - Part 2 · Edition 5.1968 → replaced by Edition 4.1998

Cleaning screw for drainage objects made of hard PE

DIN 539 edition 10.1955 → withdrawn

Cleaning screw for drainage objects made of gray cast iron R 3/4 "and R 1 1/4"

DIN 539 edition 11.1942x → withdrawn

Cleaning screws for drainage parts

Cross edition 11.1952

DIN 540 · Edition 2.1925 → withdrawn

NA pipes, bends, bends

DIN 541 edition 2.1925 → withdrawn

NA pipes, transitions, transition bends

DIN 542 edition 1.1922 → withdrawn

NA pipes, S pieces

DIN 543 edition 1.1922 → withdrawn

NA pipes, T-pieces, angled

DIN 544 edition 1.1922 → withdrawn

NA tubes, cross pieces, angled

DIN 545 edition 8.1952 → withdrawn

LNA connectors and socket plugs

DIN 545 edition 9.1924 → withdrawn

Drain pipe fittings for NA pipes and LNA pipes

DIN 546 edition 9.2010 → current

Slotted nuts

The standard contains the dimensional specifications and technical delivery conditions for slotted nuts of sizes M1 to M20 and specifies their designation.

DIN 546 edition 9.1986 → replaced by edition 9.2010

Slotted nuts

DIN 546 edition 11.1970 → replaced by edition 9.1986

Slotted nuts

DIN 546 edition 2.1954x → withdrawn

Slotted nuts · M1 to M20

Cross edition 3.1962

DIN 546 edition 4.1949 → withdrawn

Slotted nuts, two-hole nuts, cross-hole nuts · M1 to M20

DIN 546 Edition 7.1939 → withdrawn

Slotted nuts · Metric thread M1 to M20, Whitworth thread 1/2 "to 3/4"

DIN 546 edition 12.1931 → withdrawn

Slotted nuts · Metric thread

DIN 546 Edition 7.1923 → withdrawn

Slotted nuts · Metric thread

DIN 547 edition 8.2006 → current

Two-hole nuts

The standard contains the dimensional specifications and technical delivery conditions for two-hole nuts in sizes M2 to M10 and specifies their designation.

DIN 547 edition 9.1986 → replaced by edition 8.2006

Two-hole nuts

The standard contains the dimensional specifications and technical delivery conditions for two-hole nuts and specifies their designation.

DIN 547 edition 11.1970 → replaced by edition 9.1986

Two-hole nuts

DIN 547 edition 2.1954x → withdrawn

Two-hole nuts M1 to M20

Cross edition 3.1962

DIN 547 edition 4.1949 → withdrawn

Slotted nuts, two-hole nuts, cross-hole nuts · M1 to M20

DIN 547 Edition 7.1939 → withdrawn

Two-hole nuts · Metric thread

DIN 547 edition 11.1922 → withdrawn

Two-hole nuts · Metric thread

DIN 548 Edition 1.2007 → current

Cross-hole nuts

The standard contains the dimensional specifications and technical delivery conditions for cross-hole nuts in sizes M2 to M10 and specifies their designation.

DIN 548 edition 8.2006 → replaced by edition 1.2007

Cross-hole nuts

The standard contains the dimensional specifications and technical delivery conditions for cross-hole nuts in sizes M2 to M10 and specifies their designation.

DIN 548 edition 9.1986 → replaced by edition 8.2006

Cross-hole nuts

The standard contains the dimensional specifications and technical delivery conditions for cross hole nuts and specifies their designation.

DIN 548 edition 11.1970 → replaced by edition 9.1986

Cross-hole nuts

DIN 548 edition 2.1954x → withdrawn

Cross hole nuts M1 to M20

Cross edition 3.1962

DIN 548 · Edition 4.1949 → withdrawn

Slotted nuts, two-hole nuts, cross-hole nuts · M1 to M20

DIN 548 Edition 7.1939 → withdrawn

Cross-Hole Nuts · Metric Thread

DIN 548 edition 11.1922 → withdrawn

Cross-Hole Nuts · Metric Thread

DIN 549 edition 10.1923 → replaced by DIN 546 edition 7.1939

Slotted nuts · Whitworth thread

DIN 550 edition 2.1956 → withdrawn

Grub screws with tapered point 1/4 "to 3/4"

DIN 550 edition 4.1925 → withdrawn

Grub screws · with conical shoulder · Whitworth thread

1/4 "to 3/4"

DIN 551 edition 9.1986 → replaced by DIN EN 24766 edition 10.1992

Grub screws with slot and tapered point

ISO 4766 edition 1983 modified

DIN 551 edition 2.1972 → replaced by edition 9.1986

Grub screws with slot and tapered point

DIN 551 edition 4.1956 → withdrawn

Grub screws with tapered point M1 to M20 and M18 × 2 to M20 × 2

DIN 551 edition 1.1951 → withdrawn

Grub screws with tapered shoulder M1 to M20, M18 × 2 and M20 × 2

DIN 551 · Edition 6.1943 → withdrawn

Grub screws · with taper · M1 to M20

DIN 551 edition 5.1924 → withdrawn

Grub screws · with taper · Metric thread

DIN 552 edition 1.1956 → withdrawn

Grub screws with point 1/4 "to 1"

DIN 552 edition 4.1926x → withdrawn

Grub screws · with point · Whitworth thread

1/2 "to 1"; Cross edition 4.1943

DIN 553 edition 9.1986 → replaced by DIN EN 27434 edition 10.1992

Grub screws with slot and point

ISO 7434 edition 1983 modified

DIN 553 edition 2.1972 → replaced by edition 9.1986

Grub screws with slot and point

DIN 553 edition 2.1953 → withdrawn

Grub screws with point M1 to M24 and M18 × 2 to M24 × 2

DIN 553 Edition 6.1937x → withdrawn

Grub screws · with point · M1 to M24

DIN 553 edition 5.1924 → withdrawn

Grub screws · with point · Metric thread

DIN 554 edition 10.1929x → withdrawn

Hexagon nuts 3/4 "to 4", W 72 × 1/4 "to W 99 × 1/4", version mg

DIN 555 edition 10.1987 → replaced by DIN EN 24034 edition 2.1992

Hexagon nuts · thread M5 to M100 × 6 · product class C

DIN 555 edition 12.1983 → replaced by edition 10.1987

Hexagon nuts · thread M5 to M100 × 6 · product class C

DIN 555 edition 12.1972 → replaced by edition 12.1983

Hexagon nuts · Metric thread · Version g

DIN 555 - Part 1 · Edition 1.1951x → withdrawn

(Raw) hexagon nuts M5 to M64 and M72 × 6 to M100 × 6 Version g

Cross edition 11.1952

DIN 555 - Part 1 · Edition 1.1941 → withdrawn

Hexagon nuts M5 to M100 Version g

DIN 555 - Part 2 · Edition 4.1954 → withdrawn

(Raw) Hex Nuts 1/4 "to 4"

DIN 555 - part 2 edition 4.1934x → withdrawn

Hexagon nuts · 7/16 "to 4", version g

DIN 555 edition 4.1934 → withdrawn

Raw hex nuts · Metric thread from M 5 to M 10, Whitworth thread from 1/4 "to 4"

DIN 556 edition 4.1936 → withdrawn

Square bolts with hex nuts

DIN 556 - Supplement · Edition 10.1926 → withdrawn

Square bolts with hex nuts · Weights

DIN 556 edition 4.1925 → withdrawn

Square bolts with hex nuts

DIN 557 edition 1.1994 → current

Square nuts · Product class C

The standard contains the dimensional specifications and technical delivery conditions for square nuts (product class C) and specifies their designation.

DIN 557 edition 2.1985 → replaced by edition 1.1994

Square nuts · Product class C

DIN 557 edition 12.1972 → replaced by edition 2.1985

Square nuts, design g

DIN 557 - Part 1 · Edition 1.1941x → withdrawn

(Raw) square nuts M5 to M20

Cross edition 2.1962

DIN 557 - Part 2 · Edition 5.1954 → withdrawn

(Raw) square nuts 1/4 "to 1 1/2"

DIN 557 - Part 2 Edition 7.1936x → withdrawn

Square nuts · 7/16 "to 1 1/2", design g

DIN 557 edition 4.1925 → withdrawn

Raw square nuts

DIN 558 edition 9.1987 → replaced by DIN EN 24018 edition 2.1992

Hexagon bolts with thread up to the head · Thread M5 to M36 · Product class C

DIN 558 edition 12.1983 → replaced by edition 9.1987 and DIN ISO 4018 edition 9.1987

Hexagon bolts with thread up to head · Thread M5 to M36 · Product class C, ISO 4018 modified

DIN 558 edition 12.1967 → replaced by edition 12.1983

Hexagon head bolts, thread almost up to the head · Metric thread, version g

DIN 558 - Part 1 Edition 8.1953 → withdrawn

(Raw) hexagon head bolts, thread approximately to head · M5 to M24

DIN 558 - Part 1 · Edition 1.1941 → withdrawn

Hexagon head screws, thread almost up to head · M5 to M24, design g

DIN 558 - Part 2 · Edition 4.1954 → withdrawn

Hex (Raw) Bolts, Thread Approximately 1/4 "to 1" Head

DIN 558 Edition 7.1934x → withdrawn

Raw hexagon bolts, thread almost to head

DIN 559 edition 4.1936x → withdrawn

Round-head screws with square neck and square nut for insertion in wood · Whitworth thread

DIN 559 - Supplement · Edition 10.1926 → withdrawn

Round-head screws with square neck and square nut for embedding in wood · Weights

DIN 559 edition 4.1925 → withdrawn

Round-head screws with square neck and square nut for embedding in wood

DIN 560 edition 10.1956 → withdrawn

Hexagon head bolts with tenons, small hexagon and thread up to head 1/4 "to 1 1/2"

DIN 560 edition 7.1926 → withdrawn

Hexagon bolts with tenons, small hexagon and thread up to the head, 1/4 "to 1 1/2", version m

DIN 561 edition 2.1995 → current

Hexagon head bolts with tenons and a small hexagon

The standard contains the dimensional specifications and technical delivery conditions for hexagon bolts with tenons and small hexagon and specifies their designation.

DIN 561 edition 2.1985 → replaced by edition 2.1995

Hexagon head bolts with tenons and a small hexagon

DIN 561 edition 12.1967 → replaced by edition 2.1985

Hexagon screw with tenon, small hexagon and thread up to the head · Metric thread, metric fine thread

DIN 561 edition 6.1953 → withdrawn

Hexagon head bolts with pin, small hexagon and thread up to head M6 to M56 and M20 × 2 to M30 × 2, M36 × 3 to M56 × 3

DIN 561 edition 1.1951 → withdrawn

Hexagon head bolts with tenons, small hexagon head and thread up to head M6 to M36 and M20 × 2 to M36 × 3

DIN 561 edition 12.1938x → withdrawn

Hexagon bolts with pin, small hexagon and thread up to the head · M6 to M36, version with

DIN 561 edition 6.1923 → withdrawn

Hexagon bolts with tenons, small hexagon from M 6 to M 39

DIN 562 edition 5.2013 → current

Square nuts, low shape - product grade B

The standard specifies the requirements for square nuts with a low shape of sizes M1.6 to M10.

DIN 562 edition 10.2000 → replaced by edition 5.2013

Square nuts, low shape - product grade B

The standard contains the dimensional specifications and technical delivery conditions for square nuts, low form and specifies their designation.

DIN 562 edition 2.2000 → replaced by edition 10.2000

Square nuts, low shape - product grade B

DIN 562 edition 9.1987 → replaced by edition 2.2000

Square nuts, low shape · Product class B

DIN 562 edition 2.1985 → replaced by edition 9.1987

Square nuts, low shape · Product class B

DIN 562 edition 12.1972 → replaced by edition 2.1985

Square nuts, low shape

DIN 562 Edition 7.1960 → withdrawn

Flat square nuts M1.7 to M10

DIN 562 edition 9.1941 → withdrawn

Square nuts, flat · M1.7 to M10 · Version w

DIN 562 edition 4.1923 → withdrawn

Flat square nuts · Metric thread

DIN 563 edition 7.1926x → withdrawn

Hexagon head screws with point, small hexagon and thread to head, 1/2 "to 1 1/2", version m

Cross edition 1.1943

DIN 564 edition 2.1995 → current

Hexagon head screws with shoulder point and small hexagon

The standard contains the dimensional specifications and technical delivery conditions for hexagonal bolts with shoulder point and small hexagon and specifies their designation.

DIN 564 edition 2.1985 → replaced by edition 2.1995

Hexagon head screws with shoulder point and small hexagon

DIN 564 edition 12.1967 → replaced by edition 2.1985

Hexagon head screws with shoulder point, small hexagon and thread up to the head · Metric thread, metric fine thread

DIN 564 · Edition 6.1953 → withdrawn

Hexagon bolts with shoulder point, small hexagon and thread up to the head M6 to M36 and M20 × 2 to M30 × 2, M36 × 3

DIN 564 edition 1.1951 → withdrawn

Hexagon head screws with point, small hexagon and thread up to head · M6 to M36 and M20 × 2 to M36 × 3

DIN 564 edition 12.1938x → withdrawn

Hexagon head screws with point, small hexagon and thread up to head · M6 to M36, version w

DIN 564 edition 12.1923 → withdrawn

Hexagon head screws with point, small hexagon, thread from M 6 to M 39

DIN 565 edition 4.1936x → withdrawn

Countersunk screws with nose with hexagon or square nut for insertion into metal · Whitworth thread

DIN 565 - supplement 1 edition 10.1926 → withdrawn

Countersunk screws with nose with hexagon or square nut for insertion in metal · Weights

with hexagon nut

DIN 565 - Supplement 2 Edition 10.1926 → withdrawn

Countersunk screws with nose with hexagon or square nut for insertion in metal · Weights

with square nut

DIN 565 edition 4.1925 → withdrawn

Countersunk screws with nose with hexagon or square nut for insertion in metal

DIN 566 edition 4.1936x → withdrawn

Countersunk screws with square neck and square nut for insertion in wood · Whitworth thread

DIN 566 - supplement 1 edition 10.1926 → withdrawn

Countersunk screws with square neck and square nut for embedding in wood · Weights

DIN 566 edition 4.1926 → withdrawn

Countersunk screws with square neck and square nut for embedding in wood

DIN 567 edition 4.1936x → withdrawn

Countersunk screws with square neck and square nut for insertion in metal · Whitworth thread

DIN 567 - supplement 1 edition 10.1926 → withdrawn

Countersunk screws with square neck and square nut for insertion in metal weights

DIN 567 edition 1.1926 → withdrawn

Countersunk screws with square neck and square nut for insertion in metal

DIN 568 edition 4.1936x → withdrawn

Countersunk countersunk head screws with square nut · Whitworth thread

DIN 568 - supplement 1 edition 10.1926 → withdrawn

Countersunk countersunk head screws with square nut · Weights

DIN 568 edition 4.1925 → withdrawn

Countersunk countersunk head screws with square nut

DIN 569 edition 4.1936x → withdrawn

Button-head screws with nose and hexagon nut for insertion in metal · Whitworth thread

DIN 569 - Supplement · Edition 10.1926 → withdrawn

Button-head screws with nose and hexagon nut for insertion in metal · Weights

DIN 569 edition 4.1925 → withdrawn

Button-head screws with nose and hexagon nut for insertion into metal

DIN 570 edition 10.1952 → withdrawn

Square wood screws

DIN 570 edition 10.1928 → replaced by DIN 571 edition 1.1941

Square wood screws

DIN 571 Edition 12.2016 → current

Hexagon wood screws

The standard specifies the properties of hexagonal wood screws that are used outside of areas requiring approval. Thread diameters from 4 to 20 mm.

DIN 571 edition 11.2010 → replaced by edition 12.2016

Hexagon wood screws

The standard contains the dimensional specifications and technical delivery conditions for hexagonal wood screws and specifies their designation.

DIN 571 edition 12.1986 → replaced by edition 11.2010

Hexagon wood screws

DIN 571 edition 3.1975 → replaced by edition 12.1986

Hexagon wood screws

DIN 571 edition 12.1967 → withdrawn

Hexagon wood screws

DIN 571 - supplement 1 edition 11.1942 → withdrawn

Hexagon wood screws

DIN 571 edition 1.1941 → withdrawn

Hexagon wood screws

DIN 571 edition 10.1928 → withdrawn

Hexagon wood screws

DIN 572 edition 2.1923 → withdrawn

Press-finished cylinder screws · Metric thread

DIN 573 edition 2.1923 → withdrawn

Press-finished button-head screws · Metric thread

DIN 574 edition 2.1923 → withdrawn

Press-finished countersunk screws · Metric thread

DIN 575 edition 2.1923 → withdrawn

Pressed raised raised countersunk head screws · Metric thread

DIN 576 edition 2.1923 → withdrawn

Press-finished cylinder head screws with thread up to the head · Metric thread

DIN 577 edition 2.1923 → withdrawn

Press-finished button-head screws with thread up to the head · Metric thread

DIN 578 edition 2.1923 → withdrawn

Press-finished countersunk screws with thread up to the head · Metric thread

DIN 579 edition 2.1923 → withdrawn

Press-finished raised countersunk head screws with thread up to the head · Metric thread

DIN 580 edition 9.2010 → current

Eye bolts

The standard specifies the properties and labeling of steel and stainless steel eyebolts and provides information on their correct use.

DIN 580 edition 8.2003 → replaced by edition 9.2010

Eye bolts

DIN 580 edition 3.1972 → replaced by edition 8.2003

Eye bolts

DIN 580 - Part 1 · Edition 2.1956x → withdrawn

Eye bolts with collar and groove M8 to M68 and M20 × 2 to M30 × 2, M36 × 3 to M48 × 3, M56 × 4 to M100 × 4, M72 × 6 to M100 × 6

Cross edition 7.1956

DIN 580 - Part 1 · Edition 1.1942 → withdrawn

Eye bolts with collar and groove · M8 to M100

DIN 580 - Part 1 · Edition 1.1926 → withdrawn

Eye bolts with collar and groove · Metric thread

DIN 580 - Part 2 · Edition 1.1957 → withdrawn

Eye bolts with collar and groove 1/2 "to 2 1/2" and W68 × 1/4 "to W99 × 1/4"

DIN 580 - Part 2 · Edition 1.1926 → withdrawn

Eye bolts with collar and groove 1/2 "to 2 1/2", W68 × 1/4 "to W99 × 1/4"

DIN 580 - Part 2 · Edition 1.1926 → withdrawn

Eye bolts with collar and groove · Whitworth thread

DIN 581 - Part 1 · Edition 1.1942 → withdrawn

Eye bolts with collar and outlet · Metric thread

DIN 581 - Part 1 · Edition 1.1926 → withdrawn

Eye bolts with collar and outlet · Metric thread

DIN 581 - Part 2 · Edition 1.1926 → withdrawn

Eye bolts with collar and outlet 1/2 "to 2 1/2" and W68 × 1/4 "to W99 × 1/4"

DIN 581 - Part 2 · Edition 1.1926 → withdrawn

Eye bolts with collar and outlet · Whitworth thread

DIN 582 Edition 9.2010 → current

Ring nuts

The standard specifies the properties and the marking of ring nuts made of steel and stainless steel and provides information on their correct use.

DIN 582 edition 8.2003 → replaced by edition 9.2010

Ring nuts

DIN 582 edition 4.1971 → replaced by edition 8.2003

Ring nuts

DIN 582 - Part 1 · Edition 2.1956x → withdrawn

Ring nuts M8 to M68 and M20 × 2 to M30 × 2, M36 × 3 to M48 × 3, M56 × 4 to M100 × 4, M72 × 6 to M100 × 6

Cross edition 7.1956

DIN 582 - Part 1 · Edition 1.1942 → withdrawn

Ring nuts M8 to M100

DIN 582 - Part 1 · Edition 1.1926 → withdrawn

Ring nuts · Metric thread

DIN 582 - Part 2 · Edition 1.1957 → withdrawn

Ring nuts 1/2 "to 2 1/2" and W68 × 1/4 "to W99 × 1/4"

DIN 582 - Part 2 · Edition 1.1926 → withdrawn

Ring nuts 1/2 "to 2 1/2", W68 × 1/4 "to W99 × 1/4"

DIN 584 Edition 7.1928 → withdrawn

Set screws with square socket and point · Whitworth thread

DIN 585 - Part 1 Edition 7.1928 → withdrawn

Set screws with internal square and cup point · Whitworth thread

DIN 585 - Part 2 · Edition 7.1928 → withdrawn

Set screws with square socket and cup point · Whitworth pipe thread

DIN 585 - Part 3 Edition 7.1929 → withdrawn

Set screws with square socket (adjusting ring screw) · Metric thread

DIN 587 - Part 1 · Edition 7.1928 → withdrawn

Set screws with square neck and point · Metric thread

DIN 587 - Part 2 Edition 7.1928 → withdrawn

Set screws with square neck and point · Whitworth thread

DIN 590 edition 1.1928 → withdrawn

Basement gully without cleaning opening

DIN 591 - Part 1 edition 8.1989 → withdrawn

Class L 15 basement drains with cleaning opening · Compilation

The standard contains the compilation of all individual parts that belong to a basement drain.

DIN 591 - part 2 edition 8.1989 → withdrawn

Class L 15 basement drains with cleaning opening · Individual parts

The standard contains information about individual parts that belong to a basement drain.

DIN 591 - Part 1 · Edition 6.1973 → replaced by Edition 8.1989

Basement drains with internal cleaning opening · Compilation

DIN 591 - Part 2 · Edition 6.1973 → replaced by Edition 8.1989

Basement drains with internal cleaning opening · Individual parts

DIN 591 - Part 1 · Edition 3.1953 → withdrawn

Basement drains with cleaning opening · Compilation

DIN 591 - Part 2 · Edition 3.1953 → withdrawn

Basement drains with cleaning opening · Housing

DIN 591 - Part 3 · Edition 3.1953 → withdrawn

Basement drains with cleaning opening · grids, cleaning cover, insert cover, sealing ring

DIN 591 - Part 4 Edition 3.1953 → withdrawn

Basement drains with cleaning opening · Bucket, handle

DIN 591 edition 1.1928 → 12.1952 withdrawn

Basement gully with cleaning opening

The standard contains the compilation of all individual parts that belong to a basement drain.

DIN 592 - Part 2 Edition 11.1939 → withdrawn

Ceiling drain for dairies

DIN 592 - Part 3 · Edition 1.1943 → withdrawn

Ceiling drain 50 mm outlet

DIN 592 - Part 4 · Edition 1.1943 → withdrawn

Ceiling drain 70 mm outlet

DIN 592 · Edition 6.1930 → withdrawn

Ceiling gully

2nd edition of the standard

DIN 593 - Part 1 · Edition 10.1953 → withdrawn

Attachment for road drain made of gray cast iron · Composition

DIN 593 - Part 1 · Edition 7.1926 → withdrawn

Attachment for street gullies with wide grating · Composition

DIN 593 - Part 2 · Edition 10.1953 → withdrawn

Attachment for road drain made of cast iron · Frame

DIN 593 - Part 2 · Edition 7.1926 → withdrawn

Attachment for street gullies with wide grating frame

DIN 593 - Part 3 · Edition 10.1953 → withdrawn

Attachment for road drain made of gray cast iron · Grate with longitudinal bars

DIN 593 - Part 3 · Edition 7.1926 → withdrawn

Attachment for street gullies with wide grate Grate L (with longitudinal bars)

DIN 593 - Part 4 Edition 10.1953 → withdrawn

Attachment for road drain made of gray cast iron · Grate with cross bars

DIN 593 - Part 4 Edition 7.1926 → withdrawn

Attachment for street gullies with wide grate Grate Q (with cross bars)

DIN 594 - Part 1 · Edition ?? → withdrawn

Bath drain without cleaning opening with drain connection at 5 °, 20 ° and 45 ° inclination

DIN 594 - Part 2 Edition 11.1938 → withdrawn

Bathroom drain with cleaning opening and drain connection with an inclination of 5 °, 20 ° and 45 °

DIN 594 - Part 3 Edition 11.1938 → withdrawn

Bathroom drain with side inlet and drainage connection with an inclination of 5 °, 20 ° and 45 °

DIN 594 - part 4 edition 1.1943 → withdrawn

Bath drain with upper inlet

DIN 594 - Part 5 · Edition 1.1943 → withdrawn

Bathroom drain with side inlet

DIN 594 edition 4.1930 → withdrawn

Bath drain with drainage connector at an incline of 5 °, 20 ° and 45 °

1st edition of the standard

DIN 595 - Part 1 · Edition 1.1932x → withdrawn

Cleaning openings with wedge lock for shut-off devices

Cross edition 4.1943

DIN 595 - Part 2 · Edition 1.1932x → withdrawn

Cleaning openings with toggle lock for shut-off devices

Cross edition 4.1943

DIN 595 - Part 3 · Edition 1.1932x → withdrawn

Cleaning openings with screw cap for shut-off devices

Cross edition 4.1943

DIN 596 edition 1.1932 → withdrawn

Handwheels for shut-off devices in property drainage systems according to DIN 1986

DIN 597 - Part 1 · Edition 7.1938 → withdrawn

Attachment for yard drain · light, form A

DIN 597 - Part 2 · Edition 1.1954 → withdrawn

Attachment for yard drain · Form B, 5 t test load

DIN 597 - Part 2 Edition 7.1938 → withdrawn

Attachment for yard drain · light, form B

DIN 597 - Part 3 · Edition 1.1954 → withdrawn

Attachment for yard drain · Form C, 600 kg test load

DIN 597 - Part 3 Edition 11.1938 → withdrawn

Attachment for yard drain · light, form C

DIN 597 - Part 4 · Edition 1.1954 → withdrawn

Attachment for yard drain · Form D, 15 t test load

DIN 597 edition 4.1925 → withdrawn

Attachment for yard drain · light

DIN 598 edition 4.1925 → withdrawn

Attachment for yard drain heavy

DIN 600 edition 10.1926x → withdrawn

Hexagon head screws · 7/16 "to 1 1/2", version mg

DIN 600 Edition 10.1926 → withdrawn

Semi-bare hexagon bolts

DIN 601 edition 9.1987 → replaced by DIN EN 24016 edition 2.1992

Hexagon head bolts with shank · thread M5 to M52 · product class C

DIN 601 · Edition 6.1984 → replaced by Edition 9.1987 and DIN ISO 4016

Hexagon head bolts with shank · thread M5 to M52 · product class C, ISO 4016 modified

DIN 601 edition 12.1983 → replaced by edition 6.1984

Hexagon head bolts with shank · thread M5 to M52 · product class C, ISO 4016 modified

DIN 601 edition 11.1970 → replaced by edition 12.1983

Hexagon bolts · without hexagon nut - with hexagon nut, version g

DIN 601 - Part 1 Edition 9.1951 → withdrawn

(Raw) hexagon bolts, without nut - with hexagon nut · M5 to M52

DIN 601 - Part 1 - Supplement 1 Edition 11.1942 → withdrawn

Hexagon bolts, without nut, with hexagon nut · M5 to M52

DIN 601 - Part 1 · Edition 1.1941 → withdrawn

Hexagon bolts, without nut or with hexagon nut · M5 to M52, version g

DIN 601 - Part 2 · Edition 4.1954 → withdrawn

(Raw) hexagon bolts, without nut - with hexagon nut 1/4 "to 2"

DIN 601 Edition 7.1934x → withdrawn

Hexagon bolts without nuts

DIN 602 Edition 7.1936 → withdrawn

Square bolts without nuts

DIN 602 Edition 7.1925 → withdrawn

Square bolts without nuts

DIN 603 edition 5.2017 → current

Round-head screws with square neck

The standard specifies properties for button-head screws with a square neck, with metric threads in sizes M5 to M20 in product class C.

DIN 603 edition 9.2010 → replaced by edition 5.2017

Round-head screws with square neck

DIN 603 edition 10.1981 → replaced by edition 9.2010

Round-head screws with square neck

DIN 603 edition 11.1970 → withdrawn

Round-head screws with square neck

DIN 603 - Part 1 · Edition 5.1953 → withdrawn

(Raw) truss-head bolts with square neck, without nut - with square nut · M5 to M20

DIN 603 - Part 1 · Edition 1.1941 → withdrawn

Round-head screws with square neck · without nut or with square nut · M5 to M20

DIN 603 - Part 2 · Edition 5.1954 → withdrawn

(Raw) truss head screws with square neck, without nut - with square nut, for embedding in wood 1/4 "to 3/4"

DIN 603 - Part 2 Edition 7.1936x → withdrawn

Round-head screws with square neck · without nut, for embedding in wood · 7/16 "to 3/4"

DIN 603 Edition 7.1925 → withdrawn

Round-head screws with square neck for embedding in wood without a nut

DIN 604 edition 5.2017 → current

Countersunk screws with nose

The standard specifies properties for countersunk screws with a nose, with metric thread sizes M6 to M24 in product class C.

DIN 604 edition 9.2010 → replaced by edition 5.2017

Countersunk screws with nose

The standard applies to countersunk screws in sizes M6 to M24 with a nose in product class C.

DIN 604 edition 10.1981 → replaced by edition 9.2010

Countersunk screws with nose

DIN 604 edition 11.1970 → replaced by edition 10.1981

Countersunk screws with nose

DIN 604 - Part 1 · Edition 5.1953 → withdrawn

(Raw) countersunk head screws with nose, without nut - with hexagon nut · M6 to M24

DIN 604 - Part 1 · Edition 1.1941 → withdrawn

Countersunk screws with nose, without nut or with hexagon nut · M6 to M24

DIN 604 - Part 1 - Supplement 1 · Edition 1.1941 → withdrawn

Countersunk screws with nose, without nut, with hexagon nut · M6 to M24

DIN 604 - Part 2 · Edition 5.1954 → withdrawn

(Raw) countersunk screws with nose, without nut - with hexagon nut 1/4 "to 1"

DIN 604 - Part 2 · Edition 7.1936x → withdrawn

Countersunk screws with nose, without nut, for recessing in metal · 7/16 "to 1"

DIN 604 Edition 7.1925 → withdrawn

Countersunk screws with nose for insertion in metal without a nut

DIN 605 edition 9.2010 → current

Countersunk screws with a high square neck

The standard applies to countersunk screws in sizes M6 to M24 with a high square neck in product class C.

DIN 605 edition 10.1981 → replaced by edition 9.2010

Countersunk screws with a high square neck

DIN 605 edition 11.1970 → withdrawn

Hexagon head screws with square neck · with high square, without hexagon nut, with hexagon nut

DIN 605 - Part 1 · Edition 12.1955 → withdrawn

(Raw) countersunk head screws with square neck, without nut - with hexagon nut · M5 to M20

DIN 605 - Part 1 · Edition 5.1953 → withdrawn

(Raw) countersunk screws with square neck for embedding in wood, without nut - with hexagon nut · Metric thread

DIN 605 - Part 1 · Edition 1.1941 → withdrawn

Countersunk screws with square neck · without nut or with hexagon nut, for recessing in wood · M5 to M10

DIN 605 - Part 2 · Edition 5.1954 → withdrawn

(Raw) countersunk screws with square neck, without nut, for embedding in wood 1/4 "to 3/4"

DIN 605 - Part 2 Edition 7.1936x → withdrawn

Countersunk screws with square neck · without nut, for embedding in wood · 7/16 "to 3/4"

DIN 605 edition 10.1926 → withdrawn

Countersunk screws with square neck to be embedded in wood without a nut

DIN 606 - Part 1 · Edition 3.1963 → withdrawn without replacement

Countersunk countersunk head screws · without nut with square nut, metric thread design g

DIN 606 - Part 1 · Edition 5.1953 → withdrawn

(Raw) countersunk countersunk head screws, without nut - with square nut · M6 to M10

DIN 606 - Part 1 · Edition 1.1941 → withdrawn

Countersunk countersunk screws · without nut or with square nut · M6 to M10

DIN 606 - Part 2 · Edition 5.1954 → withdrawn

(Raw) countersunk countersunk screws, without nut 1/4 "to 1/2"

DIN 606 - Part 2 Edition 7.1936x → withdrawn

Countersunk countersunk head screws without nut 7/16 "and 1/2"

DIN 606 edition 10.1926 → withdrawn

Countersunk countersunk head screws without nut

DIN 607 edition 9.2010 → current

Button-head screws with nose

The standard applies to button-head screws in sizes M8 to M16 with a nose in product class C.

DIN 607 edition 10.1981 → replaced by edition 9.2010

Button-head screws with nose

DIN 607 edition 11.1970 → withdrawn

Button-head screws with nose · without hexagon nut, with hexagon nut

DIN 607 - Part 1 · Edition 5.1953 → withdrawn

(Raw) button-head screws with nose, without nut - with hexagon nut · M5 to M24

DIN 607 - Part 1 · Edition 1.1941 → withdrawn

Button-head screws with nose · without nut or with hexagon nut · M5 to M24

DIN 607 - Part 2 · Edition 5.1954 → withdrawn

(Raw) button-head bolts with nose, without nut 1/4 "to 1"

DIN 607 - Part 2 Edition 7.1936x → withdrawn

Button-head screws with nose · without nut, for insertion in metal · 7/16 "to 1"

DIN 607 edition 1.1926 → withdrawn

Button-head bolts with nose without nut

DIN 608 edition 9.2010 → current

Countersunk screws with a low square neck

The standard applies to countersunk screws of sizes M10 and M12 with a low square neck in product class C.

DIN 608 edition 10.1981 → replaced by edition 9.2010

Countersunk screws with a low square neck

DIN 608 edition 11.1970 → replaced by edition 10.1981

Countersunk screws with a low square neck

DIN 608 - Part 1 · Edition 5.1953 → withdrawn

(Raw) countersunk head screws with square neck, without nut - with square nut, for insertion into metal · M10 and M12

DIN 608 - Part 1 · Edition 1.1941 → withdrawn

Countersunk screws with square neck · without nut or with square nut, for recessing in metal · M10 and M12

DIN 608 - Part 2 · Edition 5.1954 → withdrawn

(Raw) countersunk screws with square neck, without nut, for embedding in metal · 1/4 "to 1"

DIN 608 - Part 2 Edition 7.1936x → withdrawn

Countersunk screws with square neck · without nut, for recessing in metal · 7/16 "to 1"

DIN 608 Edition 4.1926 → withdrawn

Countersunk screws with square neck to be embedded in metal without a nut

DIN 609 Edition 12.2016 → current

Hexagon fitting screws with long threaded pin

The standard specifies properties for hexagon fitting screws with long threaded stems. Thread diameter 8 to 52 mm (product class A thread diameter <= 10 mm and product class B> = 12 mm). For hexagon fitting screws with a thread diameter> 39 mm, the standard only applies with regard to dimensions and tolerances.

DIN 609 edition 2.1995 → replaced by edition 12.2016

Hexagon fitting screws with long threaded pin

The standard contains the dimensional specifications and technical delivery conditions for hexagonal fitting screws with long threaded pins and specifies their designation.

DIN 609 edition 7.1984 → replaced by edition 2.1995

Hexagon fitting screws with long threaded pin

DIN 609 edition 1.1971 → replaced by edition 7.1984

Hexagon fitting screws with long threaded pin

DIN 609 edition 4.1956 → withdrawn

Hexagon fitting screws M10 to M52 and M18 × 2 to M33 × 2, M36 × 3 to M52 × 3, long

DIN 609 edition 11.1953 → withdrawn

Hexagon fitting screws, long thread

DIN 609 edition 9.1951 → withdrawn

Hexagon fitting screws · long thread

DIN 609 edition 4.1942 → withdrawn

Hexagon fitting screws · M10 to M52, version m or mg, long thread

DIN 610 edition 7.1984 → 7.1995 withdrawn without replacement

Hexagon fitting screws with short threaded pin

DIN 610 · Edition 1.1971 → replaced by Edition 7.1984

Hexagon fitting screws · with short threaded pin

DIN 610 · edition 4.1956 → withdrawn

Hexagon fitting screws M10 to M52 and M18 × 2 to M33 × 2, M36 × 3 to M52 × 3, short

DIN 610 edition 11.1953 → withdrawn

Hexagon fitting screws, short thread

DIN 610 edition 9.1951 → withdrawn

Hexagon fitting screws · short thread

DIN 610 · Edition 4.1942 → withdrawn

Hexagon fitting screws · M10 to M52, version m or mg, short thread

DIN 611 edition 5.2010 → current

Rolling Bearings · Overview

The standard gives an overview of the bearing types and designs as well as the associated product standards.

DIN 611 edition 10.1990 → replaced by edition 5.2010

Rolling Bearings · Overview

DIN 611 edition 11.1973 → replaced by edition 10.1990

Rolling bearings · Rolling bearing parts, rolling bearing accessories and spherical plain bearings, overview

DIN 611 edition 8.1942 → withdrawn

Rolling Bearings and Rolling Bearing Parts · Overview

DIN 612 - Part 1 Edition 8.1942 → withdrawn

Rolling bearings · Basic standards, types, designation

DIN 612 - Part 2 Edition 8.1942 → withdrawn

Rolling bearings · Basic standards, types, symbols

DIN 612 - Part 1 · Edition 4.1929 → withdrawn

Transverse bearing single row light transverse bearing bore d = 4 to 110

DIN 612 - Part 2 · Edition 4.1927 → withdrawn

Transverse bearing single row light transverse bearing bore d = 120 to 320

DIN 613 - Part 1 Edition 7.1928 → withdrawn

Transverse bearing single row medium-weight transverse bearing bore d = 10 to 95

DIN 613 - Part 2 · Edition 4.1927 → withdrawn

Transverse bearing single row medium-weight transverse bearing bore d = 100 to 280

DIN 614 - Part 1 Edition 7.1928 → withdrawn

Transverse bearing single row heavy transverse bearing bore d = 17 to 85

DIN 614 - Part 2 · Edition 4.1927 → withdrawn

Transverse bearing single row heavy transverse bearing bore d = 90 to 240

DIN 615 edition 1.2008 → current

Rolling bearings · shoulder ball bearings · single row, not self-retaining

This standard specifies the dimensions and abbreviations for shoulder ball bearings. It offers a selection tailored to the practical needs of the user, taking into account the dimension plan according to DIN 616.

DIN 615 - supplement 1 edition 9.1994 → 8.2006 withdrawn without replacement

Rolling bearings · shoulder ball bearings · feature identifiers and simplified representations

The standard contains feature identifiers and simplified representations for shoulder ball bearings.

DIN 615 - Supplement 1 Edition 6.1994 → replaced by Edition 9.1994

Rolling bearings · shoulder ball bearings · feature identifiers and simplified representations

DIN 615 edition 1.1993 → replaced by edition 1.2008

Rolling bearings · shoulder ball bearings

DIN 615 edition 4.1959 → replaced by edition 1.1993

(Radial) shoulder ball bearings

This standard specifies the dimensions and abbreviations of single-row shoulder ball bearings: E3 to E13, E15, E19, E20, BO15, BO17, L17a, L20, L25, L30, M20. Partial compliance with ISO R 15.

DIN 615 edition 8.1942 → withdrawn

Rolling bearing · ring shoulder bearing · single row

DIN 615 edition 11.1932 → withdrawn

Shoulder ball bearings

DIN 616 · Edition 6.2000 → current

Rolling bearings · Dimension plans

The standard contains rules and dimension plans with the external dimensions for rolling bearings.

DIN 616 · Edition 6.1994 → replaced by Edition 6.2000

Rolling bearings · Dimension plans

DIN 616 edition 2.1973 → replaced by edition 6.1994

Rolling bearings · Dimension plans for external dimensions

DIN 616 · Edition 6.1961 → withdrawn

Rolling bearings · Dimension plans for external dimensions

DIN 616 - Part 1 · Edition 8.1942 → withdrawn

Rolling bearings · Basic standards · Dimensions, external dimensions

DIN 617 edition 10.2008 → current

Rolling bearings Needle roller bearings with cage Dimension series 48, 49 and 69

This standard specifies the dimensions and the abbreviation for needle roller bearings with cage for dimension series 48, 49 and 69.

DIN 617 edition 1.1993 → replaced by edition 10.2008

Rolling bearings Needle roller bearings with cage Dimension series 48 and 49

This standard specifies the dimensions and the abbreviation for needle roller bearings with cages for dimension series 48 and 49.

DIN 617 edition 6.1973 → replaced by edition 1.1993

Rolling bearings Needle roller bearings with cage, dimension series 48 and 49

DIN 617 edition 9.1959x → withdrawn

Needle roller bearings Outer rings with needle roller and cage assembly, dimensional series 49

Cross edition 1.1960

DIN 617 - part 1 edition 8.1942 → withdrawn

Rolling bearings · ring cylindrical bearings · needle roller bearings

DIN 617 - Part 2 Edition 8.1942 → withdrawn

Rolling bearings · Rolling bodies, cylindrical rollers, needles

DIN 617 - Part 3 · Edition 8.1942 → withdrawn

Rolling bearings · parts, raceway rings with rolling elements, outer rings with needles

DIN 618 edition 10.2008 → current

Rolling bearings · needle roller bearings · needle sleeves and needle sleeves, with cage

The standard specifies the dimensions for needle roller bearings with cages and needle sleeves or needle sleeves.

DIN 618 - Part 1 · Edition 3.1993 → replaced by DIN 618 Edition 10.2008

Rolling bearings · needle roller bearings · needle sleeves, needle sleeves, with cage

The standard specifies the dimensions for needle roller bearings with cages and needle sleeves or needle sleeves.

DIN 618 - Part 2 · Edition 3.1993 → replaced by DIN 618 Edition 10.2008

Rolling bearings · needle roller bearings · needle sleeves with cage, sealed

The standard specifies the dimensions for needle roller bearings with cage and needle sleeves, sealed.

DIN 618 edition 6.1973 → replaced by DIN 618 part 1 edition 3.1993

Rolling bearings · needle roller bearings · needle sleeves, needle sleeves, with cage

DIN 619 Edition 3.1924 → withdrawn

Ball bearings · overview sheet

DIN 620 - Part 1 · Edition 6.1982 → current

Rolling bearings · Measuring method for dimensional and running tolerances

DIN 620 - Part 1 · Edition 3.1963 → withdrawn

Rolling bearing tolerances · Measuring method

DIN 620 - Part 1 · Edition 8.1942 → withdrawn

Rolling bearings · Basic standards, test methods and tolerances, dimensional, form and running accuracy

DIN 620 - Part 2 · Edition 2.1988 → current

Rolling bearings · Rolling bearing tolerances · Tolerances for radial bearings

The tolerances specified in this standard ensure the functionality and interchangeability of radial roller bearings. They are used to check the similarity of bearing parts and bearings. Direct conclusions from these tolerance values ​​on the running tolerances of bearings are not possible.

DIN 620 - Part 2 · Edition 6.1982 → replaced by Edition 2.1988

Rolling bearings · Tolerances for radial bearings

DIN 620 - Part 2 · Edition 1.1965 → withdrawn

Rolling bearing tolerancesNormal tolerance (tolerance class 0)

DIN 620 - Part 3 · Edition 6.1982 → current

Rolling bearings · Tolerances for thrust bearings

DIN 620 - Part 3 · Edition 3.1964 → withdrawn

Rolling bearing tolerances narrow tolerances (tolerance classes 6, 5 and 4)

DIN 620 - Part 4 · Edition 6.2004 → current

Rolling bearings · Rolling bearing tolerances · Radial internal clearance

This part of the standard specifies values ​​for the radial internal clearance of the following bearing types: deep groove ball bearings, self-aligning ball bearings, cylindrical roller bearings, needle roller bearings and spherical roller bearings.

DIN 620 - Part 4 · Edition 8.1987 → replaced by Edition 6.2004

Rolling bearings · Rolling bearing tolerances · Radial internal clearance

This part of the standard specifies values ​​for the radial internal clearance of the following bearing types: deep groove ball bearings, self-aligning ball bearings, cylindrical roller bearings, needle roller bearings and spherical roller bearings.

DIN 620 - Part 4 · Edition 9.1983 → replaced by Edition 8.1987

Rolling bearings · Radial internal clearance

DIN 620 - Part 4 · Edition 10.1968 → replaced by Edition 9.1983

Rolling bearing tolerances · Radial internal clearance

DIN 620 - Part 4 Edition 3.1962 → withdrawn

Rolling bearings · dimensional, form and running accuracy · radial internal clearance

DIN 620 - Part 6 · Edition 6.2004 → current

Rolling bearings · Rolling bearing tolerances · Limit dimensions for edge distances

This part of the standard specifies limit values ​​for edge distances of rolling bearings in metric bearing series with cylindrical bore, the dimensions of which are specified in DIN rolling bearing standards.

DIN 620 - Part 6 · Edition 10.1993 → replaced by Edition 6.2004

Rolling bearings · Rolling bearing tolerances · Limit dimensions for edge distances

The purpose of the standard is to ensure the interchangeability of the rolling bearings in terms of edge distances by setting limit values ​​for the edge distances.

DIN 620 - Part 6 · Edition 6.1982 → replaced by Edition 10.1993

Rolling bearings · Metric bearing series · Limiting dimensions for edge distances

DIN 620 · Edition 11.1932 → withdrawn

Test methods and tolerances for ball bearings

DIN 621 edition 8.1942 → withdrawn

Rolling bearings · Basic standards, weights

DIN 622 - Part 1 · Edition 2.1979 → withdrawn

Load capacity of rolling bearings · Terms, load ratings, calculation of the equivalent load and service life

DIN 622 - supplement 1 edition 11.1962 → withdrawn

Rolling bearings · Load capacity and service life · Calculation of the dynamic load capacity of ball bearings · Diagram for finding the e and Y values

DIN 622 - Part 1 · Edition 7.1962 → withdrawn

Rolling bearings · Load capacity and service life · Terms

DIN 622 - Part 1 · Edition 8.1942 → withdrawn

Rolling bearings · Basic standards · Performance data, load capacity

DIN 622 - Part 3 · Edition 4.1962 → withdrawn

Rolling bearings · Load capacity and service life · Calculation of the static load capacity

DIN 622 - Part 1 · Edition 4.1929 → withdrawn

Ball bearings double row light transverse bearings bore d = 10 to 110

DIN 622 - Part 2 · Edition 4.1927 → withdrawn

Ball bearings double row light transverse bearings bore d = 120 to 320

DIN 623 - Part 1 · Edition 5.1993 → current

Rolling bearings · Basics · Designation, marking

The standard defines the basics, designation and marking for rolling bearings.

DIN 623 - Part 1 · Edition 3.1984 → replaced by Edition 5.1993

Designations for rolling bearings · General, bearing series symbols for ball bearings, cylindrical roller bearings and spherical roller bearings

DIN 623 - Part 1 · Edition 8.1942 → withdrawn

Rolling bearings · Basic standards · Designation, composition of the symbols

DIN 623 - Part 2 · Edition 6.2000 → current

Rolling bearings · Basics · Graphic representation of rolling bearings

The standard specifies rules for the graphic representation of rolling bearings in standards.

DIN 623 - Part 2 · Edition 8.1942 → withdrawn

Rolling bearings · Basic standards · Designation, composition of the abbreviations · Attachment of the abbreviation

DIN 623 edition 3.1973 → replaced by DIN 623 part 1 edition 3.1984

Abbreviation of the rolling bearings

DIN 623 · Edition 6.1962 → withdrawn

Rolling bearings Abbreviation

DIN 623 - Part 1 · Edition 7.1928 → withdrawn

Ball bearings double row medium-weight transverse bearings bore d = 10 to 95

DIN 623 - Part 2 · Edition 4.1927 → withdrawn

Ball bearings · double row, medium-weight transverse bearings · bore d = 100 to 280

DIN 624 - Part 1 Edition 7.1928 → withdrawn

Ball bearings double row heavy transverse bearings bore d = 17 to 85

DIN 624 - Part 2 · Edition 4.1927 → withdrawn

Ball bearings · double row heavy transverse bearings · bore d = 90 to 240

DIN 625 - Part 1 · Edition 4.2011 → current

Rolling Bearings · Radial Deep Groove Ball Bearings · Single Row

DIN 625 - Part 1 · Edition 4.1989 → replaced by Edition 4.2011

Rolling bearings · deep groove ball bearings · single row

DIN 625 - Part 1 · Edition 9.1959 → replaced by Edition 4.1989

(Radial) deep groove ball bearings · single row, without filling grooves

DIN 625 - Part 1 · Edition 8.1942 → withdrawn

Rolling bearings · ring deep groove bearings · without filling grooves, single row

DIN 625 - part 2 edition 11.1973 → replaced by DIN 625 part 1 edition 4.1989

(Radial) deep groove ball bearings · single row, without filling grooves, with tapered bore · annular groove, cover and sealing washers

DIN 625 - Part 2 Edition 10.1960 → withdrawn

(Radial) deep groove ball bearings · single row, without filling grooves, with tapered bore · annular groove, cover and sealing washers

DIN 625 - Part 2 · Edition 8.1942 → withdrawn

Rolling bearings Grooved ring bearings without filling grooves, single row (with annular groove and cover disks)

DIN 625 - Part 3 · Edition 1.2011 → current

Rolling bearings · Radial deep groove ball bearings · Double row

The standard defines dimensions and symbols.

DIN 625 - Part 3 · Edition 3.1990 → replaced by Edition 1.2011

Rolling bearings · deep groove ball bearings · double row

DIN 625 - Part 3 · Edition 9.1959 → replaced by Edition 3.1990

(Radial) deep groove ball bearings · double row, with filling grooves

DIN 625 - Part 3 Edition 8.1942 → withdrawn

Rolling bearings · ring grooved bearings · with filling grooves, two rows

DIN 625 - Part 4 · Edition 5.2010 → current

Rolling bearings · Radial deep groove ball bearings · With flange on the outer ring

The standard specifies dimensions, weights and symbols for deep groove ball bearings with a flange on the outer ring.

DIN 625 - Part 4 Edition 8.1987 → replaced by Edition 5.2010

Rolling bearings · Deep groove ball bearings with flange on the outer ring

DIN 625 - Part 1 - Supplement 1 Edition 9.1994 → 8.2006 withdrawn without replacement

Rolling bearings · Deep groove ball bearings, single row · Feature identifiers and simplified representations

The standard contains feature identifiers and simplified representations for single row deep groove ball bearings.

DIN 625 - Part 1 - Supplement 1 · Edition 6.1994 → replaced by Edition 9.1994

Rolling bearings · Deep groove ball bearings, single row · Feature identifiers and simplified representations

DIN 625 - Part 3 - Supplement 1 Edition 9.1994 → 8.2006 withdrawn without replacement

Rolling bearings · deep groove ball bearings, double row · feature identifiers and simplified representations

The standard contains feature identifiers and simplified representations for deep groove ball bearings, double row.

DIN 625 - Part 3 - Supplement 1 · Edition 6.1994 → replaced by Edition 9.1994

Rolling bearings · deep groove ball bearings, double row · feature identifiers and simplified representations

DIN 625 - Part 4 - Supplement 1 Edition 9.1994 → 8.2006 withdrawn without replacement

Rolling bearings · Deep groove ball bearings with flange on the outer ring - feature identifiers and simplified representations

The standard contains feature identifiers and simplified representations for deep groove ball bearings with a flange on the outer ring.

DIN 625 - Part 4 - Supplement 1 · Edition 6.1994 → replaced by Edition 9.1994

Rolling bearings · Deep groove ball bearings with flange on the outer ring · Feature identifiers and simplified representations

DIN 626 - Part 1 · Edition 7.1999 → current

Rolling bearings · deep groove ball bearings with spherical outer ring surface and enlarged inner ring · radial insert ball bearings

The standard specifies main and connecting dimensions, weights and symbols for radial insert ball bearings.

DIN 626 - Part 1 · Edition 2.1979 → replaced by Edition 7.1999

Rolling bearings · Deep groove ball bearings with spherical outer ring surface and enlarged inner ring, radial insert ball bearings

DIN 626 - Part 2 - Correction 1 · Edition 5.2000 → current

Corrections to DIN 626 - Part 2 Edition 7.1999

DIN 626 - Part 2 · Edition 7.1999 → current

Rolling bearings · Deep groove ball bearings with spherical outer ring surface and widened inner ring · Housing for radial insert ball bearings

The standard specifies the main and connection dimensions, weights and symbols for radial insert ball bearing housings.

DIN 626 - Part 2 · Edition 2.1979 → replaced by Edition 7.1999

Rolling bearings · Deep groove ball bearings with a spherical outer ring surface and a widened inner ring, cast housing for radial insert ball bearings

DIN 626 - Part 3 Edition 2.1979 → replaced by DIN 626 Part 2 Edition 7.1999

Rolling bearings · Deep groove ball bearings with a spherical outer ring surface and an enlarged inner ring, sheet steel housing for radial insert ball bearings

DIN 627 edition 7.2000 → 7.2006 withdrawn without replacement

Rolling bearings · Design of supplementary sheets for feature identifiers and simplified representations

The standard contains the principles according to which the supplementary sheets of the product standards 'Characteristic identifiers and simplified representations' are created.

DIN 627 - supplement 1 edition 7.2000 → 7.2006 withdrawn without replacement

Rolling bearings · Design of supplementary sheets for feature identifiers and simplified representations · Overview of feature identifiers

Table 1 of the standard contains an overview of all feature identifiers used for the creation of the supplementary sheets 'Feature identifiers and simplified representations' for roller and spherical bearings.

DIN 627 - Supplement 2 Edition 7.2000 → 7.2006 withdrawn without replacement

Rolling bearings · Design of supplementary sheets for feature identifiers and simplified representations · Overview of manufacturer's symbols

In the following table, the standard contains an overview of the known manufacturers for the use of abbreviations in item characteristic lists (SML) according to DIN 4000 Part 12.

DIN 628 - Part 1 · Edition 1.2008 → current

Rolling bearings · Radial angular contact ball bearings · Single row, self-retaining

The standard specifies dimensions and abbreviations for single-row self-retaining radial angular contact ball bearings without a filling groove with a cage and a contact angle of 40 °.

DIN 628 - Part 1 - Supplement 1 Edition 9.1994 → 8.2006 withdrawn without replacement

Rolling bearings · Radial angular contact ball bearings, single row, self-retaining - feature identifiers and simplified representations

The standard contains feature identifiers and simplified representations for radial angular contact ball bearings, single row, self-retaining.

DIN 628 - Part 1 edition 12.1993 → replaced by edition 1.2008

Rolling bearings · Radial angular contact ball bearings, single row, self-retaining

DIN 628 - Part 1 Edition 3.1973 → replaced by Edition 12.1993, DIN 628 Parts 3 and 4 Edition 12.1993 and DIN 628 Part 5 Edition 6.1994

(Radial) angular contact ball bearings · single row and double row

DIN 628 - Part 1 Issue 3.1962 → withdrawn

(Radial) angular contact ball bearings · single row and double row

DIN 628 - Part 1 · Edition 8.1942 → withdrawn

Rolling bearings · Annular angular contact bearings

DIN 628 - Part 2 Edition 9.1959 → 3.1991 withdrawn without replacement

(Radial) angular contact ball bearings · not self-retaining, single row

DIN 628 - Part 2 · Edition 8.1942 → withdrawn

Rolling bearings · angular contact bearings · not self-retaining, single row

DIN 628 - Part 3 · Edition 2.2008 → current

Rolling bearings · Radial angular contact ball bearings · Double row

The standard specifies dimensions for double row radial angular contact ball bearings.

DIN 628 - Part 3 - Supplement 1 Edition 9.1994 → 8.2006 withdrawn without replacement

Rolling bearings · radial angular contact ball bearings · double row, with cage · feature identifiers and simplified representations

The standard contains feature identifiers and simplified representations for radial angular contact ball bearings, double row, with cage.

DIN 628 - Part 3 · Edition 12.1993 → replaced by Edition 2.2008

Rolling bearings · Radial angular contact ball bearings · double row, with cage

The standard specifies dimensions for double row radial angular contact ball bearings.

DIN 628 - Part 4 Edition 2.2008 → current

Rolling bearings Radial angular contact ball bearings Single row, double-acting - not self-retaining, with split inner ring (four-point bearing)

The standard specifies dimensions for radial angular contact ball bearings, four-point bearings with a split inner ring.

DIN 628 - Part 4 - Supplement 1 Edition 9.1994 → 8.2006 withdrawn without replacement

Rolling bearings · Radial angular contact ball bearings · Single row, not self-retaining - four point bearings, with split inner ring · Feature identifiers and simplified representations

The standard contains feature identifiers and simplified representations for radial angular contact ball bearings, single row, not self-retaining. Four point bearing with split inner ring.

DIN 628 - Part 4 Edition 12.1993 → replaced by Edition 2.2008

Rolling bearings · Radial angular contact ball bearings, single row, not self-retaining · Four-point bearings with split inner ring

The standard specifies dimensions for radial angular contact ball bearings, four-point bearings with a split inner ring.

DIN 628 - Part 5 · Edition 6.2011 → current

Rolling bearings · Radial angular contact ball bearings · Double row, with separating balls

The standard specifies dimensions, weights and symbols for double-row radial angular contact ball bearings with separating balls.

DIN 628 - Part 5 - Supplement 1 Edition 9.1994 → 8.2006 withdrawn without replacement

Rolling bearings · Radial angular contact ball bearings, double row, with separating balls · Feature identifiers and simplified representations

The standard contains feature identifiers and simplified representations for radial angular contact ball bearings, two rows, with separating balls.

DIN 628 - Part 5 · Edition 6.1994 → replaced by Edition 6.2011

Rolling bearings · Radial angular contact ball bearings · Double row, with separating balls

DIN 628 - Part 6 Edition 7.1999 → current

Rolling bearings · Radial angular contact ball bearings · Single row, contact angle 15 ° and 25 °

The standard specifies dimensions, weights and symbols for single-row radial angular contact ball bearings.

DIN 630 · Edition 2.2011 → current

Rolling bearings · Radial self-aligning ball bearings · Double row, cylindrical and tapered bore

This standard specifies the dimensions and abbreviations of (radial) self-aligning ball bearings with cylindrical and tapered bores.

DIN 630 · Edition 9.2009 → replaced by Edition 2.2011

Rolling bearings · Radial self-aligning ball bearings · Double row, cylindrical and tapered bore

DIN 630 · edition 11.1993 → replaced by edition 9.2009

Rolling bearings · Radial self-aligning ball bearings · Double row, cylindrical and tapered bore

DIN 630 - Part 1 · Edition 5.1960 → replaced by DIN 630 Edition 11.1993

(Radial) self-aligning ball bearings · cylindrical and tapered bore

DIN 630 - Part 1 · Edition 8.1942 → withdrawn

Rolling bearings · ring self-aligning bearings · double row

DIN 630 - Part 2 Edition 10.1960 → withdrawn

(Radial) self-aligning ball bearings, wide inner ring · Inner ring with clamping sleeve

DIN 630 - Part 2 · Edition 8.1942 → withdrawn

Rolling bearings spherical self-aligning bearings double-row (with wide inner ring and with clamping sleeve)

DIN 631 · Edition 4.2010 → current

Rolling bearings · Test conditions for the experimental verification of the dynamic load rating of linear rolling guides with profiled rails and rolling element circulation

DIN 632 edition 7.1928 → withdrawn

Ball bearings · single row, lightweight adapter sleeve bearings · bore d = 15 to 100

DIN 633 Edition 7.1928 → withdrawn

Ball bearings · single row, medium-weight adapter sleeve bearings · bore d = 15 to 85

DIN 635 - Part 1 · Edition 5.2010 → current

Rolling bearings Radial spherical roller bearings Single row, cylindrical and tapered bore (barrel bearing)

The standard specifies dimensions, weights and symbols for single-row spherical roller bearings (barrel bearings).

DIN 635 - Part 1 · Edition 8.1987 → replaced by Edition 5.2010

Rolling bearings · spherical roller bearings · barrel bearings, single row

DIN 635 - Part 1 · Edition 9.1959 → replaced by Edition 8.1987

Radial roller bearings · (Radial) barrel bearings, single row

DIN 635 - Part 2 Edition 1.2009 → current

Rolling bearings · Radial spherical roller bearings · Double row, cylindrical and tapered bore

This standard specifies the main and connection dimensions, weights and symbols for double row spherical roller bearings. It offers a selection tailored to the practical needs of the user from those bearing types that would result in full utilization of the dimension plan according to ISO 15-1981 for all types of spherical roller bearings. The spherical roller bearings can differ according to the type of roller guide (fixed, loose or no ribs on the inner ring).

DIN 635 - Part 2 edition 11.1984 → replaced by edition 1.2009

Rolling bearings · spherical roller bearings, double row

DIN 635 - part 2 edition 10.1960x → replaced by edition 11.1984

Radial roller bearings · (Radial) spherical roller bearings, double row

Cross edition 3.1961

DIN 635 - Part 1 - Supplement 1 Edition 9.1994 → 8.2006 withdrawn without replacement

Rolling bearings · spherical roller bearings · single row, barrel bearings · feature identifiers and simplified representations

The standard contains feature identifiers and simplified representations of single-row barrel bearings.

DIN 635 edition 8.1942 → withdrawn

Rolling bearings · Ring barrel bearings

DIN 636 - part 1 edition 6.1993 → replaced by DIN ISO 14728 part 1 and part 2 edition 10.2005 each

Linear rolling bearings · Dynamic and static load ratings · Linear ball bearings

The standard specifies methods for calculating the dynamic and static load ratings, as well as calculating the nominal life of linear ball bearings.

DIN 636 - part 2 edition 6.1993 → replaced by DIN ISO 14728 part 1 and part 2 edition 10.2005 each

Linear rolling bearings · Dynamic and static load ratings · Profile rail ball guides

The standard specifies methods for calculating the dynamic and static load ratings of profile rail ball guides.

DIN 636 - part 3 edition 4.1994 → replaced by DIN ISO 14728 part 1 and part 2 edition 10.2005 each

Linear rolling bearings · Dynamic and static load ratings · Linear guides without rolling element circulation

The standard specifies methods for calculating the dynamic and static load ratings of roller guides without return.

DIN 637 Edition 12.2016 → current

Rolling bearings · Safety specifications for the dimensioning and operation of profile rail guides with rolling element circulation; Text in German and English

The standard applies to profile rail guides (so-called linear guides) with rolling element circulation according to DIN ISO 12090-1 and DIN ISO 12090-2 and contains safety specifications for dimensioning and operation. The standard serves to reduce the dangers when using profile rail guides and to assess residual risks and thus makes it easier for manufacturers of machines that use profile rail guides with rolling element circulation to apply the Machinery Directive 2006/42 / EC.

DIN 637 edition 8.2013 → replaced by edition 12.2016

Rolling bearings · Safety specifications for the dimensioning and operation of profile rail guides with rolling element circulation

The standard contains safety specifications for the dimensioning and operation of profile rail guides with recirculating rolling elements (linear guides).

DIN 642 Edition 7.1928 → withdrawn

Ball bearings double row light adapter sleeve bearings bore d = 15 to 100

DIN 644 Edition 12.2016 → current

Linear roller bearings · Linear rail guide with flat cage · Dimensions and tolerances

The standard specifies the installation and connection dimensions for modular rail guides with flat cages. The rolling guide unit consists of two flat rails and one or more flat cages with rolling elements.

DIN 644 edition 10.1997 → replaced by edition 12.2016

Linear rolling bearings · Guide rails for linear bearings · Dimensions and tolerances

The standard specifies the installation and connection dimensions for guide rails in linear bearings without rolling element return.

DIN 645 - Part 1 · Edition 7.1999 → withdrawn without replacement

Rolling bearings Profile rail roller guides Dimensions for series 1 to 3

The standard specifies the installation and connection dimensions for profile rail roller guides with rolling element circulation.

DIN 645 - Part 2 · Edition 7.1999 → withdrawn without replacement

Rolling bearings Profile rail rolling guides Dimensions for series 4

The standard specifies the installation and connection dimensions for profile rail roller guides with rolling element circulation.

DIN 648 edition 8.1987 → replaced by DIN ISO 12240 parts 1 and 4 edition 7.1999

Spherical plain bearings, rod ends · Dimension plans, tolerances

DIN 648 edition 1.1972 → replaced by edition 8.1987

Joint bearings, joint heads · Dimension plans for connection dimensions

DIN 649 Edition 12.2010 → current

T-slots for T-head bolts

The standard contains the dimensional specifications for T-slots for hammer screws according to DIN 186, DIN 188 and DIN 261 and specifies their designation.

DIN 649 edition 1.1987 → replaced by edition 12.2010

T-slots for T-head bolts

DIN 649 edition 12.1970 → replaced by edition 1.1987

T-slots for T-head bolts

DIN 649 - Part 1 · Edition 4.1942 → withdrawn

Unmachined T-slots for T-head bolts according to DIN 186 , DIN 188 and DIN 261 · Metric thread

DIN 649 - Part 2 Edition 9.1931x → withdrawn

Unmachined T-slots for T-head bolts according to DIN 186 , DIN 188 and DIN 261 · Whitworth thread

Cross edition 2.1942

DIN 650 Edition 10.1989 → current

Machine tools · T-slots · Dimensions

The dimensions and tolerances for T-slots specified in the standard apply to machine tool tables, pallets and workpiece or tool clamping devices on machine tools.

DIN 650 edition 3.1977 → replaced by edition 10.1989

Machine tools · T-slots · Dimensions

DIN 650 · Edition 6.1966 → withdrawn

T-slots

DIN 650 · Edition 5.1961 → withdrawn

T-slots

DIN 650 edition 1.1928 → withdrawn

T-slots, machined

DIN 651 edition 1.1928 → withdrawn

T-slots, unmachined

DIN 652 Edition 3.1924 → withdrawn

Flat knurled screws · Construction sheet · Metric thread

DIN 653 edition 8.2006 → current

Knurled screws, low shape

The standard contains the dimensional specifications and technical delivery conditions for knurled screws, low form and specifies their designation.

DIN 653 edition 9.1986 → replaced by edition 8.2006

Knurled screws, low shape

The standard contains the dimensional specifications and technical delivery conditions for knurled screws, low form and specifies their designation.

DIN 653 edition 1.1971 → replaced by edition 9.1986

Flat knurled screws

DIN 653 edition 7.1953 → withdrawn

Flat knurled screws M1 to M 10

DIN 653 edition 10.1943 → withdrawn

Knurled screws, flat M1 to M10

DIN 653 edition 3.1924 → withdrawn

Flat knurled screws with round tip · Metric thread

DIN 654 - Part 1 · Edition 3.1972 → withdrawn without replacement

Steel pin chains · Dimensions

DIN 654 - Part 1 · Edition 7.1952 → withdrawn

Steel pin chains · main dimensions

DIN 654 - Part 2 · Edition 3.1972 → withdrawn without replacement

Steel Pin Chains · Fastening Links

DIN 654 - Part 2 · Edition 7.1952 → withdrawn

Steel pin chainsFastening links form 1 and 2

DIN 654 - Part 3 · Edition 7.1952 → withdrawn

Steel pin chains · Fastening links form 73 for side fastening

DIN 654 edition 4.1928 → withdrawn

Steel pin chains

DIN 655 edition 2.1957 → withdrawn

Wire ropes made from wires of the same diameter

DIN 655 edition 12.1952 → withdrawn

Wire ropes for cranes and hoists

DIN 655 edition 9.1942 → withdrawn

Wire ropes for cranes and hoists

DIN 655 edition 11.1933 → withdrawn

Wire ropes for cranes, elevators, pulleys and similar purposes

DIN 656 edition 9.1942 → withdrawn

Wire ropes in Seale, Warrington and cored wire designs for special purposes

DIN 657 edition 9.1942 → withdrawn

Wire ropes in Seale design for traction sheave elevators

DIN 658 edition 1.1987 → 01.1998 withdrawn without replacement

Double open-ended spanners made of sheet steel · Test torques according to row D

DIN 658 edition 4.1976 → replaced by edition 1.1987

Double open-end wrench made of sheet steel

DIN 658 edition 12.1967 → replaced by edition 4.1976

Double open-end wrench made of sheet steel

DIN 658 - Part 1 · Edition 5.1924x → withdrawn

Sheet metal double wrench

Cross edition 11.1956

DIN 658 - Part 2 · Edition 5.1924x → withdrawn

Sheet metal double wrench · Special series

Cross edition 1.1957

DIN 659 edition 11.1982 → replaced by DIN 3112 edition 9.2007

Socket wrench made of pipe

DIN 659 edition 8.1967 → replaced by edition 11.1982

Socket wrench made of pipe

DIN 659 edition 4.1924 → withdrawn

Socket wrench made of pipe

DIN 660 edition 1.2012 → current

Half-round rivets · Nominal diameter 1 mm to 8 mm

The standard contains the dimensional specifications and technical delivery conditions for half-round rivets and specifies their designation.

DIN 660 edition 3.2011 → replaced by edition 1.2012

Half-round rivets · Nominal diameter 1 mm to 8 mm

DIN 660 edition 5.1993 → replaced by edition 3.2011

Half-round rivets · Nominal diameter 1 to 8 mm

DIN 660 edition 7.1977 → replaced by edition 5.1993

Half-round rivets · Nominal diameter 1 to 8 mm

DIN 660 edition 6.1956x → withdrawn

Half-round rivets 1 to 9 mm in diameter

Cross edition 1.1957

DIN 660 edition 3.1944 → withdrawn

Half-round rivets 1 to 9 mm in diameter

DIN 660 edition 10.1926 → withdrawn

Half-round rivets from 1 to 9 mm in diameter

DIN 661 Edition 3.2011 → current

Countersunk rivets · Nominal diameter 1 mm to 8 mm

The standard contains the dimensional specifications and technical delivery conditions for countersunk rivets and specifies their designation.

DIN 661 edition 5.1993 → replaced by edition 3.2011

Countersunk rivets · Nominal diameter 1 to 8 mm

DIN 661 edition 7.1977 → replaced by edition 5.1993

Countersunk rivets, nominal diameter 1 to 8 mm

DIN 661 edition 6.1956x → withdrawn

Countersunk rivets 1 to 9 mm in diameter

Cross edition 6.1957

DIN 661 edition 3.1944 → withdrawn

Countersunk rivets 1 to 9 mm in diameter

DIN 661 edition 10.1926 → withdrawn

Countersunk rivets from 1 to 9 mm in diameter

DIN 662 Edition 3.2011 → current

Lens rivets · Nominal diameter 1.6 mm to 6 mm

The standard contains the dimensional specifications and technical delivery conditions for lens rivets and specifies their designation.

DIN 662 Edition 5.1993 → replaced by Edition 3.2011

Lens rivets · Nominal diameter 1.6 to 6 mm

DIN 662 edition 7.1977 → replaced by edition 5.1993

Lens rivets · Nominal diameter 1.6 to 6 mm

DIN 662 edition 6.1956 → withdrawn

Lens rivets 1.7 to 8 mm in diameter

DIN 662 Edition 3.1944 → withdrawn

Lens rivets 1.7 to 8 mm in diameter

DIN 662 edition 10.1926 → withdrawn

Lens rivets from 1.6 to 8.4 mm in diameter

DIN 663 edition 10.1926 → withdrawn

Half-round rivets with a large head · from 1 to 9 mm in diameter

DIN 664 edition 10.1926 → withdrawn

Countersunk rivets with a large head · 1 to 9 mm in diameter

DIN 665 edition 5.1924 → withdrawn

Socket wrench · for 41 to 145 mm mouth width

DIN 666 edition 5.1924 → withdrawn

Socket wrench with upper hexagon · for 41 to 145 mm mouth width

DIN 667 edition 10.1923 → replaced by DIN 670 and DIN 671 editions 10.1939

Round steel, drawn · -3 adapter units

DIN 668 edition 10.1981 → replaced by DIN EN 10278 edition 12.1999

Bright round steel · Dimensions and permissible deviations according to ISO tolerance field h11

DIN 668 edition 5.1959 → withdrawn

Bright round steel · Dimensions, permissible deviations according to ISO tolerance field h11, weights

DIN 668 edition 2.1943 → withdrawn

Round bars · drawn or turned · ISA tolerance zone h11

DIN 668 edition 10.1938 → withdrawn

Round bars · drawn or turned · ISA gauge h11

DIN 669 edition 10.1981 → replaced by DIN EN 10278 edition 12.1999

Bare steel shafts · Dimensions and permissible deviations according to ISO tolerance zone h9

DIN 669 edition 5.1959x → withdrawn

Bare steel shafts · Dimensions, permissible deviations, weights

DIN 669 edition 9.1930 → withdrawn

Steel shafts · drawn or turned, straightened and polished

DIN 670 edition 10.1981 → replaced by DIN EN 10278 edition 12.1999

Bright round steel · Dimensions and permissible deviations according to ISO tolerance field h8

DIN 670 edition 5.1959 → withdrawn

Bright round steel · Dimensions, permissible deviations according to ISA tolerance field h8, weights

DIN 670 edition 9.1939 → withdrawn

Round bars · drawn or ground · ISA tolerance zone h8

DIN 671 edition 10.1981 → replaced by DIN EN 10278 edition 12.1999

Bright round steel · Dimensions and permissible deviations according to ISO tolerance field h9

DIN 671 edition 5.1959 → withdrawn

Bright round steel · Dimensions, permissible deviations according to ISA tolerance field h9, weights

DIN 671 - Selection Sheet 1 · Edition 7.1946 → withdrawn

Round bars · drawn or ground · ISA tolerance zone h9

DIN 671 edition 2.1943 → withdrawn

Round bars · drawn or ground · ISA tolerance zone h9

DIN 671 edition 9.1939 → withdrawn

Round bars · drawn or ground · ISA tolerance zone h9

DIN 673 Edition 10.1926 → withdrawn

Large head pan rivets · 1.6 to 8.4 mm in diameter

DIN 674 · Edition 3.2011 → current

Flat-round rivets · Nominal diameter 1.4 mm to 6 mm

The standard contains the dimensional specifications and technical delivery conditions for truss rivets and specifies their designation.

DIN 674 edition 5.1993 → replaced by edition 3.2011

Round rivets · Nominal diameter 1.4 to 6 mm

DIN 674 edition 7.1977 → replaced by edition 5.1993

Round rivets · Nominal diameter 1.4 to 6 mm

DIN 674 edition 12.1953 → withdrawn

Truss rivets

DIN 674 edition 12.1950 → withdrawn

Truss rivets

DIN 674 edition 10.1926 → withdrawn

Large headed round rivets 1.6 to 8.4 mm in diameter

DIN 675 · Edition 3.2011 → current

Flat rivets (belt rivets) · Nominal diameter 3 mm to 5 mm

The standard contains the dimensional specifications and technical delivery conditions for flat rivets and specifies their designation.

DIN 675 edition 10.1993 → replaced by edition 3.2011

Flat rivets (strap rivets) · Nominal diameter 3 to 5 mm

DIN 675 edition 7.1977 → replaced by edition 10.1993

Flat rivets (strap rivets), nominal diameter 3 to 5 mm

DIN 675 Edition 7.1949 → withdrawn

Strap rivet

DIN 675 edition 10.1926 → withdrawn

Large head strap rivets · 2.5 to 6.5 mm in diameter

DIN 676 edition 5.1995 → replaced by DIN 5008 edition 4.2011

Business letter · Single forms and continuous forms

The standard specifies uniform individual forms and continuous forms for business letters in order to facilitate correspondence.

DIN 676 edition 2.1995 → replaced by edition 5.1995

Business letter · Single forms and continuous forms

DIN 676 edition 12.1976 → replaced by edition 2.1995

Business letter · A4 forms

DIN 676 edition 4.1943 → withdrawn

Letter sheet A4 pre-printed

DIN 676 edition 10.1941 → withdrawn

Letter sheet A4 pre-printed

DIN 676 edition 5.1924 → withdrawn

Business letter, standard format A4

DIN 677 Edition 4.1943 → withdrawn without replacement

Half letter sheet A5 · Forms

DIN 677 edition 10.1941 → withdrawn

Half letter sheet A5 · Forms

DIN 677 edition 4.1927 → withdrawn

Business letters, half letters, format A 5

DIN 678 - Part 1 · Edition 1.1998 → current

Envelopes · Formats

The standard defines the formats of envelopes. It gives examples of common insert formats. The format selection made is intended to largely limit the number of formats.

DIN 678 - Part 1 · Edition 4.1987 → replaced by Edition 1.1998

Envelopes · Formats

DIN 678 - Part 1 · Edition 12.1976 → replaced by Edition 4.1987

Envelopes · Formats

DIN 678 - Part 2 · Edition 2.2008 → current

Envelopes · Envelopes for processing in inserting machines, format C6 to C4

The standard is intended to make it possible to use envelopes for machine enveloping according to functional and economic aspects. The standard defines requirements that create the prerequisites for economical and technically perfect use. It is to be seen as an aid for production, application, material planning and purchasing.

DIN 678 - Part 2 · Edition 10.1994 → replaced by Edition 2.2008

Envelopes · Envelopes for processing in inserting machines, format C6 to C4

The standard is intended to make it possible to use envelopes for machine enveloping according to functional and economic aspects. It defines requirements that create the prerequisites for economical and technically perfect use. The standard is to be seen as an aid for production, application, material planning and purchasing.

DIN 678 - Part 2 · Edition 10.1984 → replaced by Edition 10.1994

Envelopes · Envelopes for processing in inserting machines

DIN 678 edition 8.1952 → withdrawn

Envelopes · Formats

DIN 678 edition 11.1924 → withdrawn

Envelope formats

DIN 679 · Edition 4.1943 → withdrawn without replacement

Postcard and small letter A6 · Forms

DIN 679 edition 10.1941 → withdrawn

Postcard A6 (world post format) · Form

DIN 679 edition 1.1928 → withdrawn

Business postcard, format A 6 (world post format)

DIN 680 edition 2.2008 → current

Window envelope · Formats and window position

The standard specifies specifications for window envelopes (U-shape envelopes and T-type mailers in accordance with DIN 678-1) that are intended for the dispatch of documents in accordance with DIN 678-2.

DIN 680 edition 1.1995 → replaced by edition 2.2008

Window envelope · Formats and window position

The standard makes specifications for window envelopes (U-shaped envelopes and T-shaped mailers in accordance with DIN 678-1) for the dispatch of documents designed in accordance with DIN 676.

DIN 680 edition 4.1987 → replaced by edition 1.1995

Window envelope · Formats and window position

DIN 680 edition 12.1976 → replaced by edition 4.1987

Window envelopes

DIN 680 edition 11.1962 → withdrawn

Window envelopes

DIN 680 edition 8.1952 → withdrawn

Window envelopes

DIN 680 edition 9.1936 → withdrawn

Window envelopes

DIN 680 edition 3.1930 → withdrawn

Window envelopes

DIN 681 edition 8.1930 → withdrawn

Business card (goods card) Standard format A 6 (105 × 148)

Committee for Economic Administration (AWV)

DIN 682 edition 1.1926 → withdrawn

Boards and frames for pictures and samples

DIN 683 Edition 4.1964 → current

Poster formats · Poster pillars and billboards

DIN 683 edition 4.1939 → withdrawn

Stop sizes, stop points

DIN 683 edition 10.1928 → withdrawn

Poster formats

DIN 684 edition 10.1941 → withdrawn

Invoice form · Standard formats A4, A5, A6

DIN 685 - Part 1 Edition 11.1981 → current

Tested round steel chains · Terms

DIN 685 - Part 2 · Edition 2.2001 → current

Tested round steel chains · Safety requirements

The standard specifies requirements with regard to materials, manufacturing processes, dimensions and mechanical-technological properties for tested round steel chains and their individual parts for general use and for lifting loads.

DIN 685 - Part 2 edition 11.1981 → replaced by edition 2.2001 and DIN EN 818 part 1 edition 8.1996

Tested round steel chains · Safety requirements

DIN 685 - Part 3 · Edition 2.2001 → current

Tested round steel chains · Test

The standard contains the test procedures for the safety requirements for tested round steel chains and their individual parts according to DIN 685 Part 2 and defines the type and scope of the individual tests.

DIN 685 - Part 3 edition 11.1981 → replaced by edition 2.2001 and DIN EN 818 part 1 edition 8.1996

Tested round steel chains · Test

DIN 685 - Part 4 Edition 2.2001 → current

Tested round steel chains · Marking, test certificate

The standard applies to tested round steel chains and their individual parts in accordance with DIN 685 Part 2 and defines their labeling for the purpose of differentiating between quality classes.

DIN 685 - Part 4 edition 11.1981 → replaced by edition 2.2001 and DIN EN 818 part 1 edition 8.1996

Tested round steel chains · Marking, test certificate

DIN 685 - Part 5 Edition 11.1981 → replaced by DIN EN 818 Part 6 Edition 3.2000

Tested round steel chains · Use

DIN 685 - Part 100 · Edition 11.2011 → current

Tested round steel chains · Additional terms

Basic standard for the area of ​​round steel chains and their accessories. It only contains terminological definitions.

DIN 685 edition 2.1971 → withdrawn

Tested round steel chains · Requirements

DIN 685 edition 10.1954 → withdrawn

Round link chains, tested · Guidelines for the requirements

DIN 685 edition 6.1943 → withdrawn

Tested chains · Guidelines for the requirements for round link chains

DIN 685 edition 12.1940 → withdrawn

Tested chains · Guidelines for requirements for round link chains

DIN 685 - Supplement · Edition 12.1940 → withdrawn

Annealing of round link chains · Leaflet

DIN 685 edition 4.1932 → withdrawn

Guidelines for requirements for round link chains

DIN 686 Edition 3.1972 → withdrawn without replacement

Dismountable link chains · Dimensions

DIN 686 - Part 1 · Edition 2.1930 → withdrawn

Articulated chains, can be dismantled, 22/18 to 50/50

DIN 686 - Part 2 · Edition 4.1928 → withdrawn

Link chains, can be dismantled, 52/36 to 148/70

DIN 687 edition 6.1944 → withdrawn

Load hook for power and manual hoists · Blanks

DIN 687 edition 12.1930 → withdrawn

Load hook for power hoists · Blanks

DIN 688 - Part 1 Edition 11.1943 → withdrawn

Load hooks and double hooks for power and manual hoists · Calculation, loading, material, testing and handling during use

DIN 688 - Part 2 Edition 11.1943 → withdrawn

Load hook and double hook for power and manual hoists · Machining of the shaft

DIN 688 edition 2.1933 → withdrawn

Load hook for manual hoists · Blanks

DIN 689 edition 7.1975 → replaced by DIN 7540 edition 10.1980

Eye hook

DIN 689 edition 5.1944 → withdrawn

Eye hook for load chains

DIN 690 edition 9.1924 → withdrawn

Grooved profiles for rope pulleys

DIN 691 edition 4.1980 → current

Tension chains for rail and road vehicles

DIN 691 edition 12.1966 → withdrawn

Tension chains for rail and road vehicles

DIN 691 edition 5.1949 → withdrawn

Tension chains for rail and road vehicles

partly replacement for DIN 75062

DIN 695 Edition 7.1986 → current

Sling chains · Hook chains, ring chains, individual parts · Quality class 2

The standard specifies the structure, load capacities and test forces of 1 to 4-leg hook and ring chains with a nominal thickness of 6 to 45 mm, as well as their individual parts such as suspension, end, transition and intermediate links and contains information about the marking and the Carrying out the exam.

DIN 695 Edition 9.1959 → replaced by Edition 7.1986

Round steel chains · hook chains, ring chains

DIN 695 edition 2.1948 → withdrawn

Round link chains, hook chains, ring chains

DIN 696 edition 8.1943 → withdrawn

Round link chains for hoists · tempered, tested, true to gauge

DIN 697 edition 4.1925 → withdrawn

Impellers without flange

DIN 698 edition 11.1938 → withdrawn

Overhead traveling cranes for electric drive · Passage profile and extreme position of the crane hook

DIN 698 - Part 1 · Edition 7.1925 → withdrawn

Overhead traveling cranes for electric drive · load capacity 5 to 30 t · passage profile and outermost position of the crane hook

DIN 698 - Part 2 Edition 7.1925 → withdrawn

Overhead traveling cranes for electric drive · Load capacity 40 to 100 t · Passage profile and outermost position of the crane hook

DIN 699 edition 11.1943 → withdrawn

Double hook for power hoists · Blanks

DIN 699 edition 2.1933 → withdrawn

Double hook for power hoist · blanks

DIN 703 edition 8.1955 → withdrawn without replacement

Bare set collars · Fastened with grub screws or heavy series pins

DIN 703 edition 1.1952 → withdrawn

Bare set collars · Fastened with threaded pins, heavy series

DIN 703 edition 2.1940 → withdrawn

Adjusting rings · Fastened by grub screws with metric thread, heavy series

DIN 704 edition 2.1940 → withdrawn

Bare set collars · Fastened by threaded pins with Whitworth thread, light series

DIN 704 Edition 7.1934 → withdrawn

Adjusting rings · Fastened by grub screws with Whitworth thread, light series

DIN 705 edition 4.2007 → current

Collars

The standard specifies the requirements for dimensions and technical delivery conditions for adjusting rings of forms A, B and C.

DIN 705 edition 10.1979 → replaced by edition 4.2007

Collars

DIN 705 edition 9.1955 → withdrawn

Bare set collars · Fastening with grub screws or pins, light series

DIN 705 edition 1.1949 → withdrawn

Bare adjusting rings, bare · Fastened with threaded pins or pins

DIN 705 edition 1.1927 → withdrawn

Adjusting rings · Fastened with split pins or tapered pins

DIN 706 edition 7.1930 → withdrawn

Adjusting rings · Fastened with threaded pins with metric thread

DIN 707 edition 2.1940 → withdrawn

Adjusting rings · Fastened by grub screws with Whitworth thread, heavy series

DIN 707 edition 7.1930 → withdrawn

Adjusting rings · Fastening with threaded pins, heavy series

DIN 708 edition 11.1930 → withdrawn

Split collars · Space requirements

DIN 711 edition 5.2010 → current

Rolling bearings · Axial deep groove ball bearings, single-acting

The standard contains dimensions, abbreviations and weights for single-acting axial deep groove ball bearings with a flat or spherical housing washer.

DIN 711 edition 2.1988 → replaced by edition 5.2010

Rolling bearings · Axial deep groove ball bearings, single-acting

DIN 711 - Part 1 edition 9.1959x → replaced by DIN 711 edition 2.1988

Axial deep groove ball bearings, single direction, with flat housing washer, with spherical housing washer and washer

Cross edition 7.1961

DIN 711 - Part 1 Edition 8.1942 → withdrawn

Rolling bearings · Grooved disc bearings, unidirectional, single row

DIN 711 - Part 2 Edition 8.1942 → withdrawn

Rolling bearings · Grooved disc bearings, single-sided, double-row

DIN 711 - Part 3 Edition 9.1959 → replaced by DIN 711 Edition 2.1988

Axial deep groove ball bearings, single direction, with cap, full complement (without cage)

DIN 711 - Part 3 Edition 8.1942 → withdrawn

Rolling bearings · Grooved disc bearings, single-sided, single-row, with cap

DIN 711 edition 11.1933 → withdrawn

Longitudinal bearing with flat thrust washers

DIN 712 edition 11.1933 → withdrawn

Longitudinal bearing with spherical washer · light row

DIN 713 edition 11.1933 → withdrawn

Longitudinal bearing with crowned washer · medium-heavy row

DIN 714 edition 11.1933 → withdrawn

Longitudinal bearing with spherical washer · heavy series

DIN 715 edition 2.2011 → current

Rolling bearings · Axial deep groove ball bearings, double-acting

The standard contains dimensions, abbreviations and weights for double-acting axial deep groove ball bearings with flat and spherical housing washers.

DIN 715 edition 9.2009 → replaced by edition 2.2011

Rolling bearings · Axial deep groove ball bearings, double-acting

DIN 715 edition 8.1987 → replaced by edition 9.2009

Rolling bearings · Axial deep groove ball bearings, double-acting

DIN 715 edition 9.1959 → replaced by edition 8.1987

Axial deep groove ball bearings, double-acting, with flat housing washers, with spherical housing washers and washers

DIN 715 edition 8.1942 → withdrawn

Rolling bearings · Grooved disc bearings, double-acting

DIN 715 edition 11.1933 → withdrawn

Interchangeable bearings with flat thrust washers

DIN 716 edition 11.1933 → withdrawn

Interchangeable bearings with spherical washers · light series

DIN 717 edition 11.1933 → withdrawn

Interchangeable bearings with spherical washer · medium-heavy series

DIN 718 edition 11.1933 → withdrawn

Interchangeable bearings with spherical washers · heavy series

DIN 719 edition 11.1933 → withdrawn

Longitudinal bearings according to DIN 711 to 714, interchangeable bearings according to DIN 715 to 718 dimensions

DIN 720 · Edition 8.2008 → current

Rolling bearings · Tapered roller bearings

The standard specifies the abbreviations and dimensions for single row metric tapered roller bearings.

DIN 720 - Supplement 1 · Edition 8.2008 → current

Rolling bearings · Tapered roller bearings - comparison of DIN and ISO symbols

DIN 720 edition 2.1979 → replaced by edition 8.2008

Rolling bearings · Tapered roller bearings

DIN 720 - Supplement 1 · Edition 2.1979 → replaced by Edition 8.2008

Rolling bearings · Tapered roller bearings, comparison of DIN and ISO symbols

DIN 720 edition 8.1970 → withdrawn

(Radial) tapered roller bearings

DIN 720 edition 9.1959 → withdrawn

(Radial) tapered roller bearings

DIN 720 - Part 1 · Edition 8.1942 → withdrawn

Rolling bearings · Ring tapered bearings, single row

DIN 720 - Part 2 · Edition 8.1942 → withdrawn

Rolling bearings Ring tapered bearings, single row (with small taper angle)

DIN 720 edition 11.1933 → withdrawn

Tapered roller bearings

DIN 722 edition 8.2005 → current

Rolling bearings · Axial cylindrical roller bearings - unidirectional

The standard contains abbreviations, dimensions and weights for single-acting axial cylindrical roller bearings. The dimensions given in table 1 form a practical selection of rolling bearings as they are contained in the general dimension plan for axial bearings ISO 104 Edition 2002.

DIN 722 edition 8.1987 → replaced by edition 8.2005

Rolling bearings · Axial cylindrical roller bearings, single-acting

The standard contains abbreviations, dimensions and weights for single-acting axial cylindrical roller bearings.

DIN 722 edition 9.1968 → replaced by edition 8.1987

Axial cylindrical roller bearings, single-acting

DIN 728 edition 2.1991 → current

Rolling bearings · Axial spherical roller bearings, single acting, with asymmetrical rollers

The standard defines dimensions and symbols.

DIN 728 - Part 1 · Edition 3.1963 → replaced by DIN 728 Edition 2.1991

Rolling bearings · Axial spherical roller bearings, single acting, with asymmetrical rollers

DIN 728 - Part 1 · Edition 8.1942 → withdrawn

Rolling bearings · Disc barrel bearings, single-acting, with clamping guide

DIN 728 - Part 2 · Edition 7.1960 → withdrawn

Rolling bearings · Axial spherical roller bearings, single-acting, with symmetrical rollers

DIN 728 - Part 2 · Edition 8.1942 → withdrawn

Rolling bearings · disc barrel bearings, single-sided, with clearance control

DIN 729 edition 8.1959 → withdrawn without replacement

Steep taper 3.5: 12

DIN 731 edition 7.1944 → withdrawn

Plate, trough and box belts with can conveyor chains A DIN 933 for bulk goods of all kinds

DIN 732 edition 5.2010 → current

Rolling bearings - Thermally permissible operating speed - Calculation and factors

The standard specifies a calculation method with which the thermally permissible operating speed can be determined for specific operating conditions.

DIN 733 edition 8.1946 → withdrawn

Single ring short slide bearing · Installation dimensions

DIN 734 edition 9.1947 → withdrawn

Short slide bearings, two-ring short slide bearings · Installation dimensions and examples

DIN 735 edition 9.1947 → withdrawn

Two-ring wide bearing · Installation dimensions

DIN 736 edition 6.2011 → current

Rolling bearings · Plummer block housings for rolling bearings of diameter series 2, with tapered bore and adapter sleeve

This standard specifies the main and connection dimensions and abbreviations for plummer block housings for the installation of rolling bearings as floating or fixed bearings.

DIN 736 edition 11.1984 → replaced by edition 6.2011

Rolling bearings · Plummer block housings for rolling bearings in diameter series 2 with tapered bore and adapter sleeve

DIN 736 edition 7.1967 → replaced by edition 11.1984

Plummer block housing for roller bearings of diameter series 2, with tapered bore and adapter sleeve · main dimensions

DIN 736 edition 4.1956 → withdrawn

Plummer block housing for rolling bearings of dimension group 2 (light series) with tapered bore and adapter sleeve · main dimensions

DIN 737 edition 6.2011 → current

Rolling bearings · Plummer block housings for rolling bearings of diameter series 3, with tapered bore and adapter sleeve

This standard specifies main and connection dimensions as well as abbreviations for plummer block housings for the installation of rolling bearings as floating bearings or fixed bearings.

DIN 737 edition 11.1984 → replaced by edition 6.2011

Rolling bearings · Plummer block housings for rolling bearings of diameter series 3 with tapered bore and adapter sleeve

DIN 737 edition 7.1967 → replaced by edition 11.1984

Plummer block housing · for roller bearings of diameter series 3, with tapered bore and adapter sleeve · main dimensions

DIN 737 edition 4.1956x → withdrawn

Plummer block housing for rolling bearings of dimension group 3 (medium-heavy series) with tapered bore and adapter sleeve · main dimensions

Cross edition 6.1956

DIN 738 edition 6.2011 → current

Rolling bearings · Plummer block housings for rolling bearings of diameter series 2, with cylindrical bore

This standard specifies the main and connection dimensions and abbreviations for plummer block housings for the installation of rolling bearings as floating or fixed bearings.

DIN 738 edition 11.1984 → replaced by edition 6.2011

Rolling bearings · Plummer block housings for rolling bearings in diameter series 2 with a cylindrical bore

DIN 738 edition 7.1967 → replaced by edition 11.1984

Plummer block housing for roller bearings of diameter series 2, with cylindrical bore · main dimensions

DIN 738 edition 4.1956 → withdrawn

Plummer block housing for rolling bearings of dimension group 2 (light series) with cylindrical bore · main dimensions

DIN 739 edition 6.2011 → current

Rolling bearings · Plummer block housings for rolling bearings of diameter series 3, with cylindrical bore

This standard specifies the main and connection dimensions and abbreviations for plummer block housings for the installation of rolling bearings as floating or fixed bearings.

DIN 739 edition 11.1984 → replaced by edition 6.2011

Rolling bearings · Plummer block housings for rolling bearings in diameter series 3 with a cylindrical bore

DIN 739 edition 7.1967 → replaced by edition 11.1984

Plummer block housing for roller bearings of diameter series 3, with cylindrical bore · main dimensions

DIN 739 edition 4.1956 → withdrawn

Plummer block housing for rolling bearings of dimension group 3 (medium-heavy series) with cylindrical bore · main dimensions

DIN 740 - Part 1 Edition 8.1986 → current

Drive technology · Flexible shaft couplings · Requirements, technical delivery conditions

Flexible shaft couplings with the specifications according to this standard are used in the field of drive technology. The standard can also be used for rigid shaft couplings. The standard summarizes the technical requirements for the design and manufacture of flexible shaft couplings. To enable an assessment according to uniform principles. In particular, the standard should be used as the technical delivery condition for the order information for the various designs and materials. The application of the standard increases the reliability of flexible shaft couplings.

DIN 740 - Part 1 · Edition 3.1975 → replaced by Edition 8.1986

Compliant shaft couplings · Main dimensions, nominal torques

DIN 740 - Part 2 Edition 8.1986 → current

Drive technology · Flexible shaft couplings · Terms and calculation bases

The standard applies to non-slip clutches whose power transmission links consist of partially or all-round flexible elastomers as well as metal-elastic spring elements. The calculation methods listed for the design of flexible shaft couplings preferably contain experience-specific loading factors and also only apply to the linear two-mass oscillator under special operating conditions. In cases where, for safety reasons or because of the technical complexity of the system to be calculated, simple approximate calculations are no longer permissible and special circumstances of multi-mass systems with regard to temporal load profiles, non-linear springs, play, etc. must be taken into account, mathematically more complex calculation methods must be used ( e.g. simulation technology). * In order not to hinder or influence progress in this area through inappropriate standardization of modern system calculation methods, only general information is given under Section 3.4.

DIN 740 - Part 2 · Edition 3.1975 → replaced by Edition 8.1986

Flexible shaft couplings · Terms, interpretation

DIN 741 edition 7.1972 → 6.1981 withdrawn without replacement

Wire rope clips for rope end connections · for subordinate requirements

DIN 741 edition 12.1958 → withdrawn

Wire rope clips · Clamps, jaws

DIN 741 edition 9.1942 → withdrawn

Wire rope clips

DIN 743 - Part 1 · Edition 12.2012 → current

Load capacity calculation of shafts and axles · Basics

The standard contains the basic equations and the methodical procedure for verifying the load-bearing capacity for shafts and axles.

DIN 743 - Part 1 edition 10.2000 → replaced by edition 12.2012

Load capacity calculation of shafts and axles · Introduction, basics

The aim of the standard is to define the design and calculation bases for shafts and axles for general mechanical engineering.

DIN 743 - Part 2 · Edition 12.2012 → current

Load capacity calculation of shafts and axles · Form numbers and notch action numbers

The standard specifies the size influencing factors, surface factors, shape numbers or notch effect numbers necessary for calculating the component fatigue strength according to DIN 743 Part 1.

DIN 743 - part 2 edition 10.2000 → replaced by edition 12.2012

Load capacity calculation of shafts and axles · Form numbers and notch action numbers

The standard contains the influencing factors required to calculate the component's fatigue strength in accordance with DIN 743 Part 1.

DIN 743 - Part 3 - Correction 1 · Edition 12.2014 → current

Load capacity calculation of shafts and axles · Material strength values, correction to DIN 743 part 3 edition 12.2012

DIN 743 - Part 3 Correction 1 · Edition 8.2014 → replaced by Correction 1 Edition 12.2014

Load capacity calculation of shafts and axles · Material strength values, correction to DIN 743 part 3 edition 12.2012

DIN 743 - Part 3 · Edition 12.2012 → current

Load capacity calculation of shafts and axles · Material strength values

The standard specifies the required material parameters for the strength verification according to DIN 743 Part 1.

DIN 743 - part 3 edition 10.2000 → replaced by edition 12.2012

Load capacity calculation of shafts and axles · Material strength values

The standard contains information on the required material strength values ​​for the strength verification according to DIN 743 Part 1.

DIN 743 - Part 4 · Edition 12.2012 → current

Load capacity calculation of shafts and axles · Fatigue strength, fatigue strength · Damage-equivalent stress amplitude

The standard applies to the proof of safety of shafts and axles in accordance with DIN 743 Part 1 in the fatigue strength range (vibration or fatigue failure) as well as in the time and fatigue strength range with a load given by load collectives.

DIN 743 - supplement 1 edition 12.2012 → current

Load capacity calculation of shafts and axles · Application examples for parts 1 to 3

The supplement contains application examples for DIN 743 Part 1 to DIN 743 Part 3 and is used to demonstrate the invoice process.

DIN 743 - supplement 1 edition 10.2000 → replaced by edition 12.2012

Load capacity calculation of shafts and axles · Application examples

The supplement contains calculation examples for the proof of fatigue strength according to DIN 743 Part 1 to DIN 743 Part 3.

DIN 743 - Supplement 2 · Edition 12.2012 → current

Load capacity calculation of shafts and axles · Application examples for part 4

The supplement contains application examples for DIN 743 Part 4 and is used to demonstrate the billing process.

DIN 745 edition 10.1942 → withdrawn

Bucket elevators with round link chains · Chain shackles for smooth and toothed rollers

DIN 746 - Part 1 · Edition 6.1950 → withdrawn

Shaft ends for lubrication pumps, for drive · Connection dimensions

DIN 746 - Part 2 · Edition 6.1950 → withdrawn

Shaft ends for lubrication pumps, with coupling · Connection dimensions

DIN 746 edition 7.1940 → withdrawn

Oil and grease pumps · Shaft ends

DIN 747 Edition 5.1976 → current

Shaft heights for machines

DIN 747 edition 6.1967 → withdrawn

Shaft heights for machines

DIN 747 - selection sheet · Edition 6.1967 → withdrawn

Shaft heights for machines · Selection for electrical machines

DIN 747 edition 12.1935 → withdrawn

Shaft heights for machines

DIN 748 - Part 1 · Edition 1.1970 → current

Cylindrical shaft ends · Dimensions, nominal torques

DIN 748 - Part 3 Edition 7.1975 → replaced by DIN EN 50347 Edition 9.2003

Cylindrical shaft ends for electrical machines

DIN 748 edition 7.1936 → withdrawn

Cylindrical shaft ends for holding belt pulleys, couplings and gears

DIN 749 edition 7.1936 → withdrawn

Tapered shaft ends for holding gears and couplings

DIN 750 · Edition 7.1936 → withdrawn

Short tapered shaft ends for mounting gears and couplings

DIN 751 edition 4.1925 → withdrawn

Ceilings · Overview

DIN 752 edition 4.1925x → withdrawn

Overhead transmission · Hanger with arm for belt switch

DIN 753 edition 4.1925x → withdrawn

Overhead transmission · Rod holder for belt switch

DIN 754 edition 4.1925x → withdrawn

Overhead transmission · Fingers for belt switch

DIN 755 edition 4.1925 → withdrawn

Overhead transmission · Lever holder for belt switch

DIN 756 edition 4.1925 → withdrawn

Lever holder with arm for belt switch

DIN 757 edition 4.1925 → withdrawn

Overhead transmission · Stop for belt switch

DIN 758 edition 4.1932 → withdrawn

Fixed couplings · Overview

DIN 759 edition 8.1937 → withdrawn

Attached coupling halves · Connection dimensions for assembly with attached coupling halves or with forged-on coupling flanges

DIN 760 edition 8.1937 → withdrawn

Forged coupling flanges · Connection dimensions

DIN 762 - Part 1 · Edition 6.2015 → current

Round steel chains · Round steel chains, pitch 5d, for chain conveyors · Quality class 3, tempered

The standard specifies dimensions and mechanical properties for tested, closely toleranced, long-link round steel chains of quality class 3 with a nominal pitch of t 5 xd and a range for the nominal diameter d from 10 mm to 23 mm and for an operating temperature of -20 ° C to +400 ° C fixed.

DIN 762 - Part 1 · Edition 9.1992 → replaced by Edition 6.2015

Round steel chains for continuous conveyors · Quality class 2, true to gauge, pitch 5d, tested

The standard applies to tested round steel chains of quality class 2 in true-to-gauge design with a pitch of t equal to 5d and defines their dimensions and mechanical properties.

DIN 762 - Part 1 · Edition 1.1982 → replaced by Edition 9.1992

Round steel chains for continuous conveyors · Quality class 2, true to gauge, pitch 5d, tested

DIN 762 - Part 2 · Edition 6.2015 → current

Round steel chains · Round steel chains, pitch 5d, for chain conveyors · Quality class 5, tempered

The standard specifies dimensions and mechanical properties for tested, closely tolerated, long-link round steel chains of quality class 5 with a nominal pitch of t 5 xd and a range for the nominal diameter d from 10 mm to 23 mm and for an operating temperature of -20 ° C to +400 ° C fixed.

DIN 762 - Part 2 · Edition 9.1992 → replaced by Edition 6.2015

Round steel chains for continuous conveyors · Quality class 3, true to gauge, pitch 5d, tested

The standard applies to tested round steel chains of quality class 3 in true-to-gauge design with a pitch of t equal to 5d and defines their dimensions and mechanical properties.

DIN 762 - Part 2 · Edition 1.1982 → replaced by Edition 9.1992

Round steel chains for continuous conveyors · Quality class 3, true to gauge, pitch 5d, tested

DIN 762 edition 1.1971 → withdrawn

Round steel chains for continuous conveyors · Chain ends tested, true to gauge, long links

DIN 762 edition 3.1955 → withdrawn

Round steel chains for continuous conveyors · Chain ends tested, true to gauge, long links

DIN 762 Edition 6.1943 → withdrawn

Round link chains for piece goods conveyors · tested, true to gauge

DIN 763 edition 12.1990 → current

Round steel chains, long links, not true to gauge, tested

The standard specifies the dimensions and mechanical properties of tested, not true to gauge, long-link round steel chains in the nominal thickness range from 4 to 16 mm.

DIN 763 edition 9.1976 → replaced by edition 12.1990

Round steel chains, tested, not true to gauge, long links

DIN 763 edition 6.1956x → withdrawn

Round steel chains for mining and motor vehicle construction · tested, not true to gauge, long link

DIN 763 edition 5.1943 → withdrawn

Round link chains for mining and the automotive industry · long link, not tested, not true to gauge

DIN 763 · Edition 6.1956 → withdrawn

Round steel chains for mining and motor vehicle construction · tested, not true to gauge, long link

DIN 763 edition 5.1943 → withdrawn

Round link chains for mining and the automotive industry · long link, not tested, not true to gauge

DIN 763 Edition 3.1937 → withdrawn

Chains · long links, not true to gauge, not tested

DIN 764 - Part 1 · Edition 10.2010 → current

Round steel chains · Round steel chains for chain conveyors · Quality class 3

The standard applies to tested quality class 3 round steel chains and defines their dimensions and mechanical properties.

DIN 764 - Part 1 · Edition 9.1992 → replaced by Edition 10.2010

Round steel chains for continuous conveyors · Quality class 2, true to gauge, division 3.5d, tested

DIN 764 - Part 1 · Edition 1.1982 → replaced by Edition 9.1992

Round steel chains for continuous conveyors · Quality class 2, true to gauge, division 3.5d, tested

DIN 764 - Part 2 · Edition 10.2010 → current

Round steel chains · Round steel chains for chain conveyors · Quality class 5

The standard applies to tested round link chains of quality class 5 and defines their dimensions and mechanical properties.

DIN 764 - Part 2 Edition 9.1992 → replaced by Edition 10.2010

Round steel chains for continuous conveyors · Quality class 3, true to gauge, division 3.5d, tested

DIN 764 - Part 2 · Edition 1.1982 → replaced by Edition 9.1992

Round steel chains for continuous conveyors · Quality class 3, true to gauge, division 3.5d, tested

DIN 764 edition 1.1971 → withdrawn

Round steel chains for continuous conveyors · Chain ends for bucket elevators, tested, semi-long links

DIN 764 edition 3.1955 → withdrawn

Round steel chains for continuous conveyors · Chain ends for bucket elevators, tested, semi-long link

DIN 764 edition 12.1942 → withdrawn

Round link chains for conveyors · tested, true to scale, not true to scale

DIN 764 edition 9.1932 → withdrawn

Conveyor chains

Replacement for DIN 670

DIN 765 edition 3.1955x → withdrawn without replacement

Round steel chains for hoists · tested, true to gauge, short-link

DIN 765 edition 7.1940x → withdrawn

Chains · short links, true to gauge, tested

DIN 765 edition 9.1932 → withdrawn

Chains, short links, doctrinal

Replacement for DIN 671

DIN 766 edition 6.2015 → current

Round steel chains · quality class 3 · true to gauge, tested

The standard applies to tested, tightly tolerated, short-link round steel chains of quality class 3 with a nominal pitch of t 2.8 xd and a range for the nominal diameter d from 10 mm to 42 mm and for an operating temperature of -20 ° C to +400 ° C . It defines the dimensions and mechanical properties of the chains.

DIN 766 edition 1.1986 → replaced by edition 6.2015

Round steel chains · quality class 3 · true to gauge, tested

The standard applies to round steel chains with nominal thicknesses of 4 to 42 mm of quality class 3 in true-to-gauge, tested design that are used for manual hoists and in the entire field of technology.

DIN 766 edition 7.1954 → replaced by edition 1.1986 and DIN 32891 edition 6.1980

Round steel chains for general purposes and hoists · Chain ends, tested, short-link

DIN 766 edition 4.1948 → withdrawn

Round steel chains for general purposes · chain ends for bucket elevators · tested

DIN 766 edition 9.1932 → withdrawn

Chains, short links, not doctrinal

Replacement for DIN 672

DIN 767 edition 8.1940 → withdrawn

Chisel steels · Cross sections

DIN 767 edition 4.1925 → withdrawn

Chisel steels · Cross sections

DIN 768 edition 10.1930 → withdrawn

Cutting steels · Terms

DIN 769 - Part 1 Edition 7.1943x → withdrawn

Thread core hole diameter, limit dimensions, metric thread

Cross edition 8.1951

DIN 769 - Part 2 Edition 7.1943x → withdrawn

Thread core hole diameter, limit dimensions, metric fine thread with pitches h = 0.2 mm and 0.25 mm

Cross edition 1.1945

DIN 769 - Part 3 · Edition 7.1943 → withdrawn

Thread core hole diameter, limit dimensions, metric fine thread with pitch h = 0.35 mm

DIN 769 - Part 4 Edition 7.1943x → withdrawn

Thread core hole diameter, limit dimensions, metric fine thread with pitch h = 0.5 mm

Cross edition 2.1952

DIN 769 - Part 5 Edition 7.1943 → withdrawn

Thread core hole diameter, limit dimensions, metric fine thread with pitch h = 0.75 mm

DIN 769 - Part 6 Edition 7.1943 → withdrawn

Thread core hole diameter, limit dimensions, metric fine thread with pitch h = 1 mm

DIN 769 - Part 7 Edition 7.1943 → withdrawn

Thread core hole diameter, limit dimensions, metric fine thread with pitch h = 1.5 mm

DIN 769 - Part 8 Edition 7.1943 → withdrawn

Thread core hole diameter, limit dimensions, metric fine thread with pitch h = 2 mm

DIN 769 - Part 9 Edition 7.1943 → withdrawn

Thread core hole diameter, limit dimensions, metric fine thread with pitch h = 3 mm

DIN 769 - Part 10 Edition 7.1943 → withdrawn

Thread core hole diameter, limit dimensions, metric fine thread with pitches h = 4 mm and 6 mm

DIN 770 - Part 1 · Edition 8.1962 → withdrawn

Shank cross-sections for turning and planing chisels · rolled and forged shanks

DIN 770 - Part 2 Edition 8.1962 → withdrawn

Shank cross-sections for turning and planing chisels · Shanks machined on all sides without special requirements on accuracy

DIN 770 edition 11.1942 → withdrawn

Cutting steels · Cross-sections for solid steels and shaft tools

DIN 770 edition 7.1925 → withdrawn

Cutting steels · cross sections

DIN 771 edition 9.1962 → current

Cutting inserts made of high-speed steel, for turning and planing chisels

DIN 771 edition 9.1953 → withdrawn

High-speed steel cutting inserts

DIN 771 edition 11.1946 → withdrawn

High-speed steel cutting inserts

DIN 771 edition 1.1927 → withdrawn

Weld-on plates · Cross-sections of the roll bars

DIN 772 edition 1.1928 → withdrawn

Passport unit · theoretical values

DIN 773 edition 1.1928 → withdrawn

Passport unit · rounded values

DIN 774 Edition 7.1923 → withdrawn

Basic terms for tolerances and dimensions

DIN 775 - Part 1 · Edition 7.1923 → withdrawn

Fits · Basic terms · Play, oversize, fit

DIN 775 - Part 2 · Edition 7.1923 → withdrawn

Fits · Basic terms · Fitting system, zero line

DIN 775 - Part 3 · Edition 1.1928 → withdrawn

Fits · Basic terms · Quality level, fit tolerance, fit unit

DIN 776 edition 1.1928 → withdrawn

Fits · Designation of the quality grades and seats

DIN 777 edition 1.1928 → withdrawn

Fits · Overview · Standard bore

DIN 778 edition 1.1928 → withdrawn

Fits · Overview · Standard shaft

DIN 779 edition 12.1980 → replaced by DIN EN 10264 part 1 edition 6.2002 and DIN EN 10264 part 3 edition 2.2003

Sectional steel wires for fully locked spiral ropes · Dimensions and technical delivery conditions

DIN 779 edition 4.1969 → withdrawn

Bare shaped wires for closed wire ropes · Technical delivery conditions

DIN 780 - Part 1 · Edition 5.1977 → current

Module series for gears · modules for spur gears

DIN 780 - Part 2 · Edition 5.1977 → current

Module series for gears · Modules for cylindrical worm gears

DIN 780 edition 2.1967 → withdrawn

Rows of modules for gears

DIN 780 edition 5.1939 → withdrawn

Gears · Module series

3rd edition of the standard

DIN 780 edition 2.1934 → replaced by edition 5.1939

Gears · Module series

2nd edition of the standard

DIN 781 Edition 12.1973 → current

Machine tools · Number of teeth of the change gears

DIN 781 edition 3.1923 → withdrawn

Number of teeth of the change gears for lead screw lathes, universal milling machines and gear processing machines

DIN 782 edition 2.1976 → 4.2008 withdrawn without replacement

Machine tools · Change gears, dimensions

DIN 782 edition 1.1929 → withdrawn

Change gears for machine tools · Construction sheet

DIN 783 edition 9.1943x → withdrawn

Shaft ends for gear drives with roller bearings

Cross edition 5.1957

DIN 784 edition 1.1928 → withdrawn

Dimensions of the work gauges · Fine fit, standard bore

DIN 785 Edition 7.1923 → withdrawn

Dimensions of the working gauges · Straight fit, standard bore

DIN 786 edition 3.1924 → withdrawn

Dimensions of the work gauges · Rough fit, standard bore

DIN 787 edition 2.2005 → current

Screws for T-slots

Screws for T-slots according to this standard are used as clamping screws for fastening workpieces or devices on machine tool tables, pallets and workpiece or tool clamping devices with T-slots according to DIN 650.

DIN 787 edition 6.2002 → replaced by edition 2.2005

Screws for T-slots

Screws for T-slots according to this standard are used as clamping screws for fastening workpieces or devices on machine tool tables, pallets and workpiece or tool clamping devices with T-slots according to DIN 650.

DIN 787 edition 5.1991 → replaced by edition 6.2002

Screws for T-slots

DIN 787 edition 8.1977 → replaced by edition 5.1991

Screws for T-slots

DIN 787 edition 11.1967 → withdrawn

T-slot bolts

DIN 787 edition 3.1958x → withdrawn

T-slot bolts

Cross edition 6.1961

DIN 788 Edition 7.1923 → withdrawn

Dimensions of the working gauges · Fine fit, standard shaft

DIN 789 edition 7.1923 → withdrawn

Dimensions of the working gauges · Straight fit, standard shaft

DIN 790 edition 3.1924 → withdrawn

Dimensions of the working gauges · Rough fit, standard shaft

DIN 791 Edition 3.1967 → current

Expanded metal

DIN 792 Edition 3.1976 → current

Cylinder countersunk head screws with nose

DIN 792 edition 3.1956 → withdrawn

Cylinder countersunk head screws with nose M24 × 2 and M30 × 2, for hard grinding machines

DIN 792 edition 1.1954 → withdrawn

Cylinder countersunk head screws with nose M24 × 2 and M30 × 2

DIN 792 edition 11.1943 → withdrawn

Cylinder countersunk head screws with nose M24 × 2 and M30 × 2

DIN 793 edition 10.1928x → withdrawn

Foundation blocks, short 1/2 "to 1"

Cross edition 6.1942

DIN 794 edition 12.1954 → 8.1985 withdrawn without replacement

Drive elements anchor plates for T-head bolts according to DIN 261 sheet 1

DIN 794 edition 4.1943 → withdrawn

Anchor plates for T-head bolts

DIN 794 edition 6.1923 → withdrawn

Anchor plates for T-head bolts

DIN 795 edition 12.1954 → withdrawn without replacement

Drive elements anchor plates for anchor bolts according to DIN 797 sheet 1

DIN 795 Edition 7.1943 → withdrawn

Anchor plates for anchor bolts

DIN 795 edition 6.1923 → withdrawn

Anchor plates, anchor bolts

DIN 796 ​​edition 12.1954 → withdrawn

Wall anchor plates for T-bolts according to DIN 261 sheet 1

DIN 796 ​​edition 4.1943 → withdrawn

Wall anchor plates for hammer screws

DIN 796 ​​edition 6.1923 → withdrawn

Wall anchor plates

DIN 797 edition 11.2009 → current

Anchor bolts

The standard specifies the properties of anchor bolts of sizes M24 to M100 × 6.

DIN 797 edition 11.1970 → replaced by edition 11.2009

Anchor bolts

DIN 797 - Part 1 Edition 7.1953 → withdrawn

Anchor bolts M24 to M64 and M72 × 6 to M100 × 6

DIN 797 - Part 1 · Edition 1.1942 → withdrawn

Anchor bolts M24 to M100

DIN 797 - Part 2 Edition 10.1955 → withdrawn

Anchor bolts · 1 "to 2 1/2" and W 72 × 1/4 "to W 99 × 1/4"

DIN 797 - Part 2 · Edition 4.1927x → withdrawn

Anchor bolts 1 "to 2 1/2", W 72 × 1/4 "to W 99 × 1/4"

DIN 797 edition 4.1927 → withdrawn

Anchor bolts

DIN 798 Edition 11.2009 → current

Anchor nuts

The standard specifies the properties of anchor nuts of sizes M24 to M100 × 6.

DIN 798 edition 12.1972 → 7.1993 withdrawn without replacement

Anchor nuts for anchor bolts according to DIN 797

DIN 798 - Part 1 · Edition 6.1956 → withdrawn

Anchor nuts M24 to M64 and M72 × 6 to M100 × 6, for anchor bolts to DIN 797 sheet 1

DIN 798 - Part 1 · Edition 1.1942 → withdrawn

Anchor nuts for anchor bolts · M24 to M100, design g

DIN 798 - Part 2 Edition 10.1927x → withdrawn

Anchor nuts · 1 "to 2 1/2" and W 72 × 1/4 "to W 99 × 1/4", for anchor bolts

Cross edition 2.1942

DIN 798 Edition 10.1927 → withdrawn

Anchor nuts for anchor bolts

DIN 799 - Part 1 Edition 10.1981 → current

Foundation blocks

DIN 799 - Part 1 · Edition 6.1942x → withdrawn

Foundation blocks · short, long

Cross edition 6.1954

DIN 799 - part 2 edition 4.1927x → withdrawn

Foundation blocks · long version, Whitworth thread

Cross edition 6.1942

DIN 799 edition 4.1927 → withdrawn

Foundation blocks · long version

DIN 800 edition 10.1959 → 2.1985 withdrawn without replacement

Spindle heads with thread and connection dimensions of the associated clamping tools

DIN 800 · Edition 5.1924 → withdrawn

Spindle heads with thread

DIN 802 - Part 1 · Edition 2.1982 → replaced by DIN EN 22857 Edition 7.1990

Tolerances of the threaded part of taps · Taps for metric ISO threads

DIN 802 - Part 1 · Edition 9.1944 → withdrawn

Taps · Manufacturing accuracies · Metric threads M1 to M68

DIN 802 - Part 2 · Edition 10.1944 → withdrawn

Taps · Manufacturing accuracy · Metric fine thread with pitch h = 0.2 to 3 mm

DIN 802 - Part 3 · Edition 3.2016 → current

Tolerances of the threaded part of taps · Ground taps for G threads according to DIN EN ISO 228-1 and Rp threads according to DIN EN 10226-1 · Manufacturing tolerances of the threaded part

The tolerances specified in the standard apply to the threaded part of taps with a ground profile (machine taps and finishing cutters) that are used to produce internal pipe threads for connections not sealing in the thread (thread abbreviation G) according to DIN EN ISO 228 Part 1 or from Whitworth - Internal pipe threads for taps and fittings (thread abbreviation Rp) according to DIN EN 10226 part 1 are intended.

DIN 802 - Part 3 · Edition 11.2008 → replaced by Edition 3.2016

Tolerances of the threaded part of taps · Ground taps for G threads according to DIN EN ISO 228-1 and Rp threads according to DIN EN 10226-1 · Manufacturing tolerances of the threaded part

The standard specifies the tolerances for the threaded part of the taps with which pipe threads according to DIN EN ISO 228 Part 1 (not sealing in the thread) and according to DIN EN 10226 Part 1 (sealing in the thread) are cut.

DIN 802 - Part 3 · Edition 6.1985 → replaced by Edition 11.2008

Tolerances of the threaded part of taps · Taps for pipe threads

DIN 802 - Part 4 · Edition 1.2012 → current

Ground taps for metric ISO threads with tolerance field 7G, 8G and special tolerances for standard and fine threads · Manufacturing tolerances of the threaded part

The tolerances specified in this standard apply to the threaded part of taps with a ground profile, over 2.8 mm thread diameter and a pitch greater than or equal to 0.5 mm, which are intended for the production of metric ISO nut threads with tolerance zones 7G and 8G. In addition, the standard regulates the use of special tolerances, which apply to specially machined materials and special machining cases.

DIN 802 - part 4 edition 8.1994 → replaced by edition 1.2012

Ground taps for metric ISO threads with tolerance field 7G, 8G and special tolerances for standard and fine threads · Manufacturing tolerances of the threaded part

DIN 802 - Part 5 · Edition 2.1997 → current

Tolerances of the threaded part of taps · Ground taps for metric ISO threads · Threads for interference fit according to DIN 8141-1 for standard and fine threads · Manufacturing tolerances of the threaded part

The standard specifies the manufacturing tolerances for the threaded part of taps that are used to produce metric ISO threads with the function of interference fit according to DIN 8141 Part 1.

DIN 802 - Part 6 Edition 7.2003 → current

Tolerances of the threaded part of taps · Ground taps for the holding thread (EG) for thread inserts made of wire according to DIN 8140 for metric ISO standard and fine threads · Manufacturing tolerances of the threaded part

The standard specifies the manufacturing tolerances for the threaded part of taps, which are intended for the production of the receiving thread (EG) for thread inserts made of wire for metric ISO threads of tolerance classes 6H mod and 6G mod according to DIN 8140 Part 1 and DIN 8140 Part 2.

DIN 802 · Edition 10.1971 → withdrawn

Taps for ISO metric threads · Tolerances of the threaded part

DIN 803 Edition 3.1977 → current

Machine tools · Feed rates for machine tools, nominal values, limit values, gear ratios

DIN 803 edition 11.1966 → withdrawn

Feed rates for machine tools · Nominal values, limit values, gear ratios

DIN 803 edition 1.1952 → withdrawn

Feed rates for machine tools · Nominal values, limit values, gear ratios

DIN 804 Edition 3.1977 → current

Machine tools · Load speeds for machine tools, nominal values, limit values, gear ratios

DIN 804 edition 11.1966 → withdrawn

Load speeds for machine tools · Nominal values, limit values, gear ratios

DIN 804 edition 11.1950 → withdrawn

Load speeds for machine tools · Nominal values, limit values, gear ratios

DIN 806 edition 2.1971 → current

Center points 60 ° without draw-off nut

DIN 806 edition 1.1961 → withdrawn

Center points 60 ° (center points)

DIN 806 edition 10.1925 → withdrawn

Grain points

DIN 807 edition 11.1966 → current

Center points 60 ° with draw-off nut

DIN 807 edition 10.1925 → withdrawn

Center punch with extraction nut

DIN 808 edition 8.1984 → current

Machine tools · Universal joints · Sizes, connection dimensions, load capacity, installation

The standard applies to single and double universal joints that are mainly used in machine tool and fixture construction. In addition to the essential main and connection dimensions for the individual sizes, diagrams are provided for determining the load-bearing capacity and instructions for the correct installation of the universal joints.

DIN 808 edition 3.1972 → replaced by edition 8.1984

Universal joints · Connection dimensions, fastenings, strength, installation

DIN 808 Edition 5.1957 → withdrawn

Universal joints · Connection dimensions, fastening, load capacity, installation

DIN 808 Edition 10.1925 → withdrawn

Ball joints · Connection dimensions

DIN 809 edition 1.1927 → withdrawn

Center punch with extraction nut, heavy

DIN 810 edition 11.1986 → current

Machine tools · Presses · Ram bores for clamping spigots · Dimensions

The standard specifies the dimensions for ram bores from 8 to 80 mm for clamping pins on pressing tools. The clamping pins establish the connection between the tool and the press ram.

DIN 810 edition 9.1956 → replaced by edition 11.1986

Pressing · Ram bores for clamping spigots

DIN 810 Edition 7.1926 → withdrawn

Pin · Connection dimensions for presses

DIN 811 edition 1.1927 → withdrawn

Dovetail wedges for presses

DIN 812 edition 2.1936x → withdrawn

Spindle flanges

Cross edition 2.1961

DIN 813 Edition 7.1923 → withdrawn

Dimensions of the work gauges · Fine fit, standard bore

DIN 814 edition 7.1923 → withdrawn

Dimensions of the working gauges · Straight fit, standard bore

DIN 815 edition 3.1924 → withdrawn

Dimensions of the work gauges · Rough fit, standard bore

DIN 816 - Part 1 · Edition 12.1956 → withdrawn

Device adapter flanges for spindle heads A according to DIN 800

DIN 816 - Part 1 · Edition 7.1942 → withdrawn

Device adapter flanges for spindle heads A according to DIN 800

DIN 816 - Part 2 Edition 12.1956 → withdrawn

Device adapter flanges for spindle heads B according to DIN 800

DIN 816 - Part 2 · Edition 7.1942x → withdrawn

Device adapter flanges for spindle heads B according to DIN 800

Cross edition 1.1943

DIN 816 - Part 3 Edition 3.1943x → withdrawn

Device adapter flanges for spindle flanges according to DIN 812

Cross edition 12.1955

DIN 817 edition 7.1923 → withdrawn

Dimensions of the working gauges · Fine fit, standard shaft

DIN 818 Edition 7.1923 → withdrawn

Dimensions of the working gauges · Straight fit, standard shaft

DIN 819 Edition 3.1924 → withdrawn

Dimensions of the working gauges · Rough fit, standard shaft

DIN 820 - supplement 1 edition 1.2000 → 6.2004 withdrawn without replacement

Standardization work · Index

The supplementary sheet contains an alphabetical index for all parts of DIN 820 and DIN EN 45020.

DIN 820 - supplement 1 edition 9.1996 → replaces edition 1.2000

Standardization work · Index

DIN 820 - supplement 1 edition 2.1987 → replaces edition 9.1996

Standardization work · Index

DIN 820 - supplement 1 edition 2.1978 → replaces edition 2.1987

Standardization work · Index

DIN 820 - Supplement 2 Edition 8.1998 → replaced by DIN 820 Part 2 Edition 12.2009

Standardization work · Supplementation of DIN designations

The guidelines are to be included for supplementary DIN designations if designations are missing in the ISO, IEC or EN standards. They are to be arranged in the national foreword of the DIN-ISO, DIN-IEC or DIN-EN standard.

DIN 820 - Part 1 · Edition 6.2014 → current

Standardization work · Principles

DIN 820 - Part 1 · Edition 5.2009 → replaced by Edition 6.2014

Standardization work · Principles

The standard describes the principles, the organization and the results of the standardization work at DIN, the German Institute for Standardization

DIN 820 - Part 1 · Edition 4.1994 → replaced by Edition 5.2009

Standardization work · Principles

DIN 820 - Part 1 · Edition 1.1986 → replaced by Edition 4.1994

Standardization work · Principles

DIN 820 - Part 1 · Edition 2.1974 → replaced by Edition 1.1986

Standardization work · Principles

DIN 820 - Part 1 · Edition 6.1960 → withdrawn

Standardization work · Basic terms, principles, course of business

DIN 820 - Part 1 · Edition 3.1951 → withdrawn

Standardization work · Principles, course of business

DIN 820 - Part 2 · Edition 12.2012 → current

Standardization work Design of documents ( ISO / IEC directives - Part 2: 2011, modified) Trilingual version CEN-CENELEC Internal Regulations - Part 3: 2011

DIN 820 - Part 2 · Edition 4.2011 → replaced by Edition 12.2012

Standardization · Design of documents (ISO / IEC directives - Part 2: 2004, modified) · Trilingual version CEN / CENELEC internal regulations - Part 3: 2009

DIN 820 - Part 2 · Edition 12.2009 → replaced by Edition 4.2011

Standardization · Design of documents (ISO / IEC directives - Part 2: 2004, modified) · Trilingual version CEN / CENELEC internal regulations - Part 3: 2009

DIN 820 - Part 2 · Edition 5.2008 → replaced by Edition 12.2009

Standardization · Design of documents (ISO / IEC directives - Part 2: 2004, modified) · Trilingual version CEN / CENELEC Internal Regulations - Part 3: 2006

DIN 820 - Part 2 · Edition 10.2004 → replaced by Edition 5.2008

Standardization work · Design of documents (ISO / IEC directives - Part 2, modified) · Trilingual version CEN / CENELEC Internal Regulations - Part 3: Rules for the structure and drafting of CEN / CENELEC publications

The standard contains the changes that result from the rules for the design of international standards according to the 4th edition of ISO / IEC Directives, Part 2, 2001.

DIN 820 - Part 2 · Edition 1.2000 → replaced by Edition 10.2004

Standardization work · Design of standards

The standard contains the rules for the design of international standards (ISO / IEC Directives, Part 3, 1997), which serve as the basis for the revision of the design rules for European standards (PNE rules) and DIN standards.

DIN 820 - Part 2 - Supplement 2 Edition 1.2000 → replaced by DIN 820 Part 2 Edition 4.2011

Standardization work · Design of standards · Examples for the design of images, tables and parts lists

This supplement to the standard shows examples of the design of images, tables and parts lists in standards.

DIN 820 - Part 2 · Edition 9.1996 → replaced by Edition 1.2000 and DIN 820 Part 2 Supplement 2 Edition 1.2000

Standardization work · Design of standards

DIN 820 - Part 2 · Edition 9.1969 → withdrawn

Standardization work · Design of standard sheets

DIN 820 - Part 2 - Supplement 1 · Edition 9.1969 → withdrawn

Standardization work · Design of standard sheets · Instructions for the structure of DIN designations

DIN 820 - Part 2 - Supplement 2 Edition 9.1969 → withdrawn

Standardization work · Design of standard sheets · Examples of application

DIN 820 - Part 2 · Edition 6.1960 → withdrawn

Standardization work · Design of standard sheets

DIN 820 - Part 2 · Edition 10.1951 → withdrawn

Standardization work · Design of standard sheets

DIN 820 - Part 3 · Edition 6.2014 → current

Standardization work · Terms

DIN 820 - Part 3 · Edition 7.2010 → replaced by Edition 6.2014

Standardization work · Terms

DIN 820 - Part 3 · Edition 7.1998 → replaced by Edition 7.2010

Standardization work · Terms

The standard contains definitions for the German set of standards that go beyond DIN EN 45020.

DIN 820 - Part 3 · Edition 4.1994 → replaced by Edition 7.1998

Standardization work · Terms

DIN 820 - Part 3 · Edition 8.1991 → replaced by Edition 4.1994

Standardization work · Terms

DIN 820 - Part 3 · Edition 3.1975 → replaced by Edition 8.1991

Standardization work · Terms

DIN 820 - Part 4 Edition 6.2014 → current

Standardization work · Course of business

DIN 820 - part 4 edition 7.2010 → replaced by edition 6.2014

Standardization work · Course of business

DIN 820 - Part 4 Edition 1.2000 → replaced by Edition 7.2010

Standardization work · Course of business

The standard describes the course of business for standardization work at DIN, the German Institute for Standardization. It defines all processing stages between the application for standardization and the publication of the standard.

DIN 820 - Part 4 - Supplement 1 Edition 9.1999 → 2.2003 withdrawn without replacement

Standardization work · Course of business, processing stages

In this supplement, the code letters for the processing stages according to DIN 820 Part 4 are specified and compared with those of the ISO / IEC code numbers.

DIN 820 - part 4 edition 1.1986 → replaced by edition 1.2000

Standardization work · Course of business

DIN 820 - Part 4 Edition 2.1974 → replaced by Edition 1.1986

Standardization work · Course of business

DIN 820 - Part 11 · Edition 6.2014 → current

Standardization work · Drafting of standards with safety-related specifications, which are VDE regulations or VDE guidelines

DIN 820 - Part 11 Edition 1.2005 → replaced by Edition 6.2014

Standardization work · Drafting of standards with safety-related specifications, which are VDE regulations or VDE guidelines

The standard applies in conjunction with DIN 820 Part 2, DIN 820 Part 12, DIN 820 Part 13 and DIN 820 Part 15 and contains supplementary provisions for the design of standards with safety-related specifications that are VDE regulations or VDE guidelines.

DIN 820 - part 11 edition 1.1995 → replaced by edition 1.2005

Standardization work · Drafting of standards with safety-related specifications, which are also VDE regulations or VDE guidelines

The standard contains supplementary specifications for the design of standards with safety-related specifications, which are also VDE regulations or VDE guidelines.

DIN 820 - part 11 edition 11.1977 → replaced by DIN 820 part 1 edition 1.1986

Standardization work · Special principles for the work of the DKE on the VDE set of regulations

DIN 820 - Part 12 · Edition 6.2014 → current

Standardization Guide for the inclusion of safety aspects in standards (ISO / IEC Guide 51: 2014)

The standard contains specifications for the design of standards with safety-related specifications.

DIN 820 - part 12 edition 1.1995 → replaced by DIN 820 part 120 edition 9.2012

Standardization work · Drafting of standards with safety-related specifications

The standard contains specifications for the design of standards with safety-related specifications.

DIN 820 - part 12 edition 1.1985 → replaced by edition 1.1995 and DIN 820 part 11 edition 1.1995

Standardization work · Standards with safety specifications · Design of standards

DIN 820 - Part 12 · Edition 5.1977 → replaced by Edition 1.1985

Standardization work · Standards with safety specifications, design

DIN 820 - Part 12 · Edition 4.1973 → withdrawn

Standardization work · Design of standard sheets, title page for VDE regulations

DIN 820 - Part 13 · Edition 3.2017 → current

Standardization work · Adoption of European documents from CEN, CENELEC and ETSI · Design of the documents

The standard defines rules for the design, structure and drafting of DIN documents, into which CEN and CENELEC documents and European ETSI standards are adopted.

DIN 820 - Part 13 · Edition 7.2010 → replaced by Edition 3.2017

Standardization work · Adoption of European documents from CEN, CENELEC and ETSI · Design of the documents

The standard defines rules for the structure and drafting of DIN documents, in which CEN and CENELEC documents and European ETSI standards are adopted.

DIN 820 - Part 13 · Edition 10.2004 → replaced by Edition 7.2010

Standardization work · Adoption of European documents from CEN, CENELEC and ETSI · Terms and design

The standard contains rules for the adoption and design of documents from DIN, in which European documents from CEN / CENELEC and ETSI are adopted. It supplements the regulations contained in the CEN / CENELEC Internal Regulations, Part 3, Annexes ZC for the publication of European documents as national documents.

DIN 820 - Part 13 · Edition 1.1995 → replaced by Edition 10.2004

Standardization work · Adoption of European standards from CEN / CENELEC and ETSI · Terms and design

DIN 820 - Part 13 · Edition 6.1976 → replaced by Edition 1.1995

Standardization work · DIN-EN standards, design

DIN 820 - Part 15 · Edition 3.2017 → current

Standardization work · Adoption of international documents from ISO and IEC · Design of the documents

The standard defines rules for the design, structure and drafting of DIN documents, into which ISO and IEC documents are adopted.

DIN 820 - Part 15 · Edition 7.2010 → replaced by Edition 3.2017

Standardization work · Adoption of international documents from ISO and IEC · Design of the documents

The standard defines rules for the structure and drafting of DIN documents into which ISO and IEC documents are adopted.

DIN 820 - Part 15 · Edition 4.2005 → replaced by Edition 7.2010

Standardization work · Adoption of international documents from ISO and IEC · Terms and design

The standard contains rules for the adoption and design of documents from DIN, in which international documents from ISO or IEC are adopted. It follows the specifications from ISO / IEC Guide 21.

DIN 820 - Part 15 · Edition 9.1996 → replaced by Edition 4.2005

Standardization work · Adoption of international standards from ISO and IEC · Terms and design

DIN 820 - Part 15 · Edition 9.1985 → replaced by Edition 9.1996

Standardization work · Adoption of international standards from ISO and IEC · Terms and design

DIN 820 - Part 15 · Edition 12.1975 → replaced by Edition 9.1985

Standardization work · DIN ISO standards, DIN IEC standards, design

DIN 820 - Part 21 Edition 7.1994 → replaced by DIN 820 Part 2 Edition 9.1996

Standardization work · Design of standards · Form, numbers, titles

DIN 820 - Part 21 · Edition 12.1987 → replaced by Edition 7.1994

Standardization work · Design of standards · Form, numbers, titles

DIN 820 - Part 21 · Edition 12.1980 → replaced by Edition 12.1987

Standardization work · Design of standards, form, numbers, titles

DIN 820 - Part 22 Edition 12.1980 → replaced by DIN 820 Part 2 Edition 9.1996

Standardization work · Design of standards, structure

DIN 820 - Part 23 Edition 9.1983 → replaced by DIN 820 Part 2 Edition 9.1996

Standardization work · Creation of standards · Word specifications, sizes, references and appendices

DIN 820 - Part 23 · Edition 12.1976 → replaced by Edition 9.1983

Standardization work · Design of standards, text information

DIN 820 - part 24 edition 11.1986 → replaced by DIN 820 part 2 edition 9.1996

Standardization work · Design of standards · Figures and tables

DIN 820 - part 24 - supplement 1 edition 1.1987 → replaced by DIN 820 part 2 edition 9.1996

Standardization work · Design of standards · Pictures and tables · Examples

DIN 820 - part 24 - supplement 1 edition 11.1986 → replaced by edition 1.1987

Standardization work · Design of standards · Pictures and tables · Examples

DIN 820 - Part 24 · Edition 12.1976 → replaced by Edition 11.1986 and DIN 820 Part 24 Supplement 1 Edition 11.1986

Standardization work · Design of standards, drawings, tables and parts lists

DIN 820 - part 25 edition 12.1980 → replaced by DIN 820 part 2 edition 9.1996

Standardization work · Creation of standards, information on materials, design, delivery and labeling

DIN 820 - part 26 edition 12.1980 → replaced by DIN 820 part 2 edition 9.1996

Standardization work · Design of standards, explanatory information

DIN 820 - Part 27 Edition 2.1987 → replaced by DIN 820 Part 2 Edition 9.1996

Standardization work · Creation of standards · Designation of standardized objects

DIN 820 - Part 27 · Edition 12.1976 → replaced by Edition 2.1987

Standardization work · Design of standards, designation of standardized objects

DIN 820 - Part 27 - Supplement 1 Edition 12.1976 → withdrawn

Standardization work · Design of standards, examples for the structure of standard designations

DIN 820 - part 29 edition 12.1980 → replaced by DIN 820 part 2 edition 9.1996

Standardization work · Drafting of standards, changes

DIN 820 - part 120 edition 9.2012 → replaced by DIN 820 part 12 edition 6.2014

Standardization guidelines for the inclusion of safety aspects in standards (ISO / IEC-Guide 51: 1999)

The standard defines a structure for the inclusion of safety aspects in standards. It is based on a risk-related approach and relates to the entire life cycle of a product, process or service.

DIN 820 - Part 120 · Edition 9.2008 → replaced by Edition 9.2012

Standardization guidelines for the inclusion of safety aspects in standards (ISO / IEC-Guide 51: 1999)

DIN 820 - Part 120 · Edition 10.2001 → replaced by Edition 9.2008

Standardization guidelines for the inclusion of safety aspects in standards (ISO / IEC-Guide 51: 1999)

DIN 821 - Part 1 · Edition 5.1992 → current

Document container · Dimensions

The standard is to be used for lying, standing, vertically hanging and laterally hanging storage. It defines dimensions, taking into account the possibilities for accommodating the document containers in shelves and filing cabinets as well as in the base cabinets of desks for writing and office machines.

DIN 821 - Part 1 · Edition 12.1981 → replaced by Edition 5.1992

Document container · Dimensions

DIN 821 - Part 1 · Edition 6.1972 → withdrawn

Document container · Dimensions

DIN 821 - Part 1 · Edition 9.1952 → withdrawn

Document container · folder, stapler

DIN 821 - Part 1 Edition 11.1942 → withdrawn

Document container · folder, stapler

DIN 821 - Part 2 Edition 10.1973 → current

Document container · Filing holes for documents, dimensions and arrangement

DIN 821 - Part 3 · Edition 3.1991 → current

Document container · Terms

The standard applies to terms that are associated with document containers. These specifications are intended to standardize the technical language for better understanding between manufacturers, dealers and users.

DIN 821 - Part 3 Edition 10.1973 → withdrawn

Document container · Terms

DIN 821 edition 7.1931 → withdrawn

Document containers, folders, binders, folders

DIN 822 Edition 7.1926 → withdrawn

Stereoscopic images in technical publications

DIN 823 edition 5.1980 → replaced by DIN 6771 part 6 edition 4.1988

Technical drawings · Sheet sizes

DIN 823 edition 8.1965 → withdrawn

Drawings · Sheet sizes, scales

DIN 823 edition 3.1956 → withdrawn

Drawings · Sheet sizes, scales

DIN 823 edition 5.1937 → withdrawn

Drawings · Sheet sizes, scales

DIN 823 edition 1.1923 → withdrawn

Drawings · Formats, scales

DIN 824 edition 3.1981 → current

Technical drawings · Fold to filing format

DIN 824 edition 1.1956 → withdrawn

Drawings · Fold on A4 for folders

DIN 824 edition 7.1929 → withdrawn

Drawings · Fold on A4 for folders

DIN 825 Edition 12.2004 → current

Signs · Dimensions

The standard specifies dimensions for rectangular, round and triangular signs regardless of the material and future information content (blank sign).

DIN 825 edition 5.1996 → replaced by edition 12.2004

Signs · Dimensions

The standard applies to the dimensions of rectangular, round and triangular signs (including additional and combination signs).

DIN 825 - Part 1 · Edition 7.1983 → replaced by DIN 825 Edition 5.1996

Sign dimensions · Square and rectangular signs

DIN 825 - Part 1 · Edition 10.1964 → replaced by Edition 7.1983

Sign dimensions · Square and rectangular signs

DIN 825 - Part 2 · Edition 7.1983 → replaced by DIN 825 Edition 5.1996

Sign dimensions · Round signs

DIN 825 - Part 2 · Edition 2.1967 → replaced by Edition 7.1983

Sign dimensions · Round signs

DIN 825 - Part 3 · Edition 7.1983 → replaced by DIN 825 Edition 5.1996

Sign dimensions · Triangular signs

DIN 825 - Part 3 · Edition 4.1975 → replaced by Edition 7.1983

Sign dimensions · Triangular signs

DIN 825 - Part 3 · Edition 2.1968 → withdrawn

Sign dimensions · Triangular signs

DIN 825 edition 7.1925 → withdrawn

Sign formats

DIN 826 edition 4.1928 → withdrawn

Magazine in A4 format (210 × 297) · Type area, image widths

2nd edition of the standard

DIN 826 edition 7.1927 → replaced by edition 4.1928

Magazine in A4 format (210 × 297) · Type area, image widths

1st edition of the standard

DIN 827 edition 9.1975 → 8.1993 withdrawn without replacement

Paper · Fiber grades

DIN 827 edition 10.1965 → withdrawn

Uncoated paper and cardboard for writing and printing purposes · Material classes

DIN 827 edition 8.1955x → withdrawn

Paper and cardboard, preferably for authorities · Material classes and properties

Cross edition 1.1957

DIN 827 edition 8.1941 → withdrawn

Paper · Plain paper for government use

DIN 828 edition 10.1928 → withdrawn

Microphotographic images · Enlargements, formats

DIN 830 edition 8.1962 → 8.1998 withdrawn without replacement

Club handles

DIN 830 edition 1.1924 → withdrawn

Club handles

DIN 831 edition 1.1924 → withdrawn

Club handles with rotatable ball handle

DIN 832 edition 1.1924 → withdrawn

Bar handles

DIN 833 edition 12.1952 → withdrawn

Studs · screw-in end ≈ 1.25 d, for screwing into gray cast iron, nut end: M8 × 1 to M10 × 1, M12 × 1.5 to M20 × 1.5, screw-in end: M8 to M20

DIN 833 edition 12.1943 → withdrawn

Studs · screw-in end ≈ 1.25 d, for screwing into gray cast iron · M8 × 1 to M20 × 1.5 for the nut end, M8 to M20 for the screw-in end

DIN 834 edition 3.1953 → withdrawn

Studs with groove · screw-in end ≈ 1.25 d, for screwing into gray cast iron, with the same thread on both sides, M18 to M52 and M18 × 1.5 to M52 × 1.5, M18 × 2, M33 × 2, M36 × 3 to M52 × 3

DIN 834 edition 12.1943x → withdrawn

Studs with groove · screw-in end ≈ 1.25 d, for screwing into gray cast iron · M18 × 1.5 to M52 × 3

DIN 835 edition 7.2010 → current

Studs · screw-in end 2 d

The standard specifies dimensions, technical delivery conditions and designation for studs with a screw-in thread length of around 2 d, in product class A, sizes M4 to M24 and fine threads M8 × 1 to M24 × 2.

DIN 835 edition 2.1995 → replaced by edition 7.2010

Studs · screw-in end ≈ 2 d

The standard contains the dimensional specifications and technical delivery conditions for studs, screw-in length approx. 2 d and specifies their designation.

DIN 835 edition 12.1972 → replaced by edition 2.1995

Studs · screw-in end ≈ 2d

DIN 835 edition 3.1953 → withdrawn

Studs · screw-in end ≈ 2 d, for screwing into aluminum alloys, with the same thread on both sides · M3 to M24 and M18 × 2 to M24 × 2

DIN 835 edition 12.1943 → withdrawn

Studs · screw-in end ≈ 2 d, for screwing into aluminum alloys · M3 to M24

DIN 836 edition 3.1953 → withdrawn

Studs · screw-in end ≈ 2 d, for screwing into aluminum alloys · nut end: M8 × 1 to M10 × 1, M12 × 1.5 to M20 × 1.5, screw-in end: M8 to M20

DIN 836 edition 12.1943 → withdrawn

Studs · screw-in end ≈ 2 d, for screwing into aluminum alloys · M8 × 1 to M20 × 1.5 for the nut end, M8 to M20 for the screw-in end

DIN 837 edition 9.2007 → current

Double ring spanners for subordinate applications · Dimensions and test torques

This standard deals with double ring spanners with unequal widths across flats. It contains the dimensions and the designation of these keys. The double ring spanners must meet the test torques series B according to DIN 899.

DIN 837 edition 1.1987 → replaced by edition 9.2007

Double ring spanners with unequal widths across flats · Test torques according to row B

DIN 837 edition 4.1976 → replaced by edition 1.1987

Double ring spanners with unequal widths across flats · Test torques according to row B

DIN 837 edition 11.1966 → replaced by edition 4.1976

Double ring spanners with different widths across flats and test torques according to row B

DIN 837 edition 5.1943x → withdrawn

Double ring spanners with unequal jaw widths · straight shape

Cross edition 3.1962

DIN 838 edition 9.2007 → current

Deep cranked double ring spanners · Test torques according to row A

The standard deals with deep cranked double ring spanners; it contains the dimensions and the designation of these keys. The deep cranked double ring spanners must meet the test torques series A according to DIN 899.

DIN 838 edition 1.1987 → replaced by edition 9.2007

Deep cranked double ring spanners with unequal widths across flats · Test torques according to row A

DIN 838 edition 4.1976 → replaced by edition 1.1987

Deep cranked double ring spanners with unequal widths across flats · Test torques according to row A

DIN 838 edition 11.1966 → replaced by edition 4.1976

Cranked double ring spanners with unequal widths across flats and test torques according to row A

DIN 838 edition 2.1957 → withdrawn

Double ring spanners with unequal widths across flats and test torques according to row A.

DIN 838 edition 5.1943 → withdrawn

Double ring spanners with unequal mouth widths · cranked shape

DIN 840 - Part 1 · Edition 11.1960 → withdrawn

Blueprint materials, blueprints · Terms and abbreviations

DIN 840 - Part 2 · Edition 11.1960 → withdrawn

Blueprint materials, blueprints · Dimensions

DIN 840 edition 10.1934 → withdrawn

Blueprint process, blueprint paper, blueprints

DIN 841 edition 7.1927x → withdrawn

Shell end mill

Cross edition 12.1944

DIN 842 - Part 1 · Edition 3.1984 → current

Arbor milling cutter · Dimensions

DIN 842 - Part 1 · Edition 10.1981 → replaced by Edition 3.1984

Arbor milling cutter · Dimensions

DIN 842 - Part 2 · Edition 1.1990 → current

Arbor milling cutter · Technical delivery conditions

The information contained in the technical terms of delivery such as designation, dimensions, tolerances, material, design and labeling apply to shell milling cutters in accordance with DIN 842 Part 1.

DIN 842 - part 2 edition 12.1981 → replaced by edition 1.1990

Arbor milling cutter · Technical delivery conditions

DIN 842 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Arbor milling cutter · Technical delivery conditions

DIN 842 edition 6.1954 → withdrawn

Machine tools for metal · Angle end mills for angle guides · Milling cutter angle 50 °

DIN 842 edition 7.1927 → withdrawn

Angle milling cutter · Milling cutter angle 50 °

DIN 843 Edition 7.1927x → withdrawn

Arbor arbors for plain and angle end mills according to DIN 841 and DIN 842 · Connection dimensions

Cross edition 12.1944

DIN 844 - Part 1 · Edition 4.1989 → current

End mill with straight shank · Dimensions

The standard contains information on dimensions and designations for end mills with straight shank. Further information such as material, design and marking are contained in DIN 844 Part 2 Technical Delivery Conditions.

DIN 844 - Part 1 · Edition 9.1978 → replaced by Edition 4.1989

End mill with straight shank · Dimensions

DIN 844 - Part 2 · Edition 4.1990 → current

End mills with straight shank · Technical delivery conditions

The information contained in the technical delivery conditions such as designation, dimensions, tolerances, material, design and labeling apply to end mills with parallel shank according to DIN 844 part 1.

DIN 844 - Part 2 · Edition 12.1981 → replaced by Edition 4.1990

End mills with straight shank · Technical delivery conditions

DIN 844 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

End mills with straight shank · Technical delivery conditions

DIN 844 edition 3.1951 → withdrawn

Machine tools for metal · End mills with straight shank

DIN 844 edition 11.1943 → withdrawn

End mill with straight shank

DIN 844 Edition 7.1927 → withdrawn

End mill with straight shank

DIN 845 - Part 1 · Edition 6.1981 → current

End mill with morse taper shank · Dimensions

The standard specifies dimensions for end mills with Morse taper shank.

DIN 845 - Part 2 · Edition 4.1990 → current

End mill with morse taper shank · Technical delivery conditions

The information contained in the technical delivery conditions such as designation, dimensions, tolerances, material, design and labeling apply to end mills with Morse taper shank according to DIN 845 Part 1.

DIN 845 - Part 2 · Edition 12.1981 → replaced by Edition 4.1990

End mill with morse taper shank · Technical delivery conditions

DIN 845 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

End mill with morse taper shank · Technical delivery conditions

DIN 845 edition 3.1951 → withdrawn

Machine tools for metal · End mills with morse taper

DIN 845 edition 2.1933 → withdrawn

End mill with morse taper

DIN 847 - Part 1 · Edition 9.1978 → current

Prism milling cutter · Dimensions

DIN 847 - Part 2 · Edition 5.1990 → current

Prism milling cutter · Technical delivery conditions

The information contained in the standard such as designation, dimensions, tolerances, material, design and marking apply to prism milling cutters according to DIN 847 Part 1.

DIN 847 - Part 2 · Edition 12.1981 → replaced by Edition 5.1990

Prism milling cutter · Technical delivery conditions

DIN 847 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Prism milling cutter · Technical delivery conditions

DIN 847 edition 3.1951 → withdrawn

Machine tools for metal · V-block milling cutters

DIN 847 edition 8.1943 → withdrawn

Prism milling cutter

DIN 847 edition 7.1927 → withdrawn

Prism milling cutter

DIN 848 - part 1 edition 3.1988 → replaced by DIN ISO 6106 edition 3.2006

Abrasive grains made from diamond and boron nitride · Description, grain size distribution

The purpose of the standard is to introduce an internationally recognized name for abrasive grains made from diamond and cubic-crystalline boron nitride with a defined and verifiable grain size distribution. The standard applies to macro grains D 1181 to D 46 made of diamond and B 1181 to B 46 made of boron nitride.

DIN 848 - Part 1 · Edition 3.1980 → replaced by Edition 3.1988

Abrasive grains made from diamond and boron nitride · Description, grain size distribution

DIN 848 - Part 2 Edition 3.1988 → replaced by DIN ISO 6106 Edition 3.2006

Abrasive grains made of diamond and boron nitride · Testing of macro-grains

The purpose of the standard is to introduce an internationally recognized test method for abrasive grains made from diamond and cubic crystalline boron nitride. The standard applies to macro grains D 1181 to D 46 for diamond and B 1181 to B 46 for boron nitride.

DIN 848 - Part 2 · Edition 3.1980 → replaced by Edition 3.1988

Abrasive grains made of diamond and boron nitride · Testing of macro-grains

DIN 848 · Edition 6.1965 → withdrawn

Diamond grits

DIN 848 edition 3.1944 → withdrawn

Diamond grits

DIN 849 · Edition 2.1960 → withdrawn without replacement

Key cutter

DIN 849 edition 1.1954 → withdrawn

Key cutter for mouth widths according to DIN 475

DIN 849 edition 8.1943 → withdrawn

Key cutter for wrenches

DIN 849 edition 10.1925 → withdrawn

Key cutter for wrenches

DIN 850 - Part 1 · Edition 4.1989 → current

Slot cutter · Dimensions

The standard contains information on dimensions and designations for slot milling cutters that are used to produce grooves, primarily for disc springs according to DIN 6888. Further information such as material, design and labeling are contained in DIN 850 Part 2 Technical Delivery Conditions.

DIN 850 - Part 1 · Edition 6.1981 → replaced by Edition 4.1989

Slot cutter · Dimensions

DIN 850 - Part 2 · Edition 4.1990 → current

Slot cutter · Technical delivery conditions

The information contained in the technical delivery conditions such as designation, dimensions, tolerances, material, design and labeling apply to slot cutters according to DIN 850 Part 1.

DIN 850 - Part 2 · Edition 12.1981 → replaced by Edition 4.1990

Slot cutter · Technical delivery conditions

DIN 850 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Slot cutter · Technical delivery conditions

DIN 850 edition 10.1961 → withdrawn

Slot cutter

DIN 850 edition 9.1955 → withdrawn

Slot cutter for grooves for disc springs according to DIN 6888

DIN 850 edition 3.1951 → withdrawn

Slot cutter for grooves for disc springs according to DIN 122

DIN 850 edition 1.1927 → withdrawn

Slot cutter for grooves for disc springs according to DIN 122

DIN 851 - Part 1 Edition 9.1991 → current

T-slot cutter with parallel shank · Dimensions

The standard contains information on dimensions and designations for T-slot milling cutters with parallel shank, which are mainly used for the production of T-slots according to DIN 650. Further information such as material, design and marking are contained in DIN 851 Part 3 Technical Delivery Conditions.

DIN 851 - Part 1 · Edition 4.1989 → replaced by Edition 9.1991

T-slot cutter with parallel shank · Dimensions

DIN 851 - Part 1 · Edition 6.1981 → replaced by Edition 4.1989

T-slot cutter with parallel shank · Dimensions

DIN 851 - Part 2 Edition 9.1991 → current

T-slot cutter with morse taper shank · Dimensions

The standard contains information on dimensions and designation for T-slot milling cutters with Morse taper shank, which are mainly used for the production of T-slots according to DIN 650. Further information such as material, design and marking are contained in DIN 851 Part 3 Technical Delivery Conditions.

DIN 851 - Part 2 · Edition 6.1981 → replaced by Edition 9.1991

T-slot cutter with morse taper shank · Dimensions

DIN 851 - Part 3 · Edition 5.1990 → current

T-slot cutter · Technical delivery conditions

The information contained in the standard such as designation, dimensions, tolerances, material, design and marking apply to T-slot milling cutters according to DIN 851 parts 1 and 2.

DIN 851 - Part 3 · Edition 12.1981 → replaced by Edition 5.1990

T-slot cutter · Technical delivery conditions

DIN 851 - Part 3 · Edition 6.1981 → replaced by Edition 12.1981

T-slot cutter · Technical delivery conditions

DIN 851 edition 1.1957 → withdrawn

End mill for T-slots according to DIN 650

DIN 851 edition 7.1926 → withdrawn

End mill for T-slots according to DIN 650

DIN 852 - Part 1 Edition 9.1991 → 6.2017 withdrawn without replacement

Mounted thread milling cutter for metric ISO threads · Dimensions

Shell-type thread milling cutters according to the standard are intended for the production of bolt threads (B) and nut threads (M) according to DIN 13 Part 19, with a pitch P up to 3 mm.

DIN 852 - Part 1 · Edition 9.1978 → replaced by Edition 9.1991

Mounted thread milling cutter for metric ISO threads · Dimensions

DIN 852 - Part 2 Edition 2.1990 → 6.2017 withdrawn without replacement

Shell-type thread milling cutter for metric ISO threads · Technical delivery conditions

The information contained in the technical delivery conditions such as designation, dimensions, tolerances, material, design and labeling apply to shell thread milling cutters for metric ISO threads in accordance with DIN 852 Part 1.

DIN 852 - Part 2 Edition 12.1981 → replaced by Edition 2.1990

Shell-type thread milling cutter for metric ISO threads · Technical delivery conditions

DIN 852 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Shell-type thread milling cutter for metric ISO threads · Technical delivery conditions

DIN 852 edition 3.1951x → withdrawn

Machine tools for metal · Shell end mills for metric threads

Cross edition 3.1957

DIN 852 edition 11.1943 → withdrawn

Shell end mills for metric threads

DIN 853 edition 11.1943x → withdrawn

Shaft arbors for shell thread milling cutters according to DIN 852

Cross edition 3.1954

DIN 855 - Part 1 · Edition 9.1978 → current

Half-round profile cutter, concave · Dimensions

DIN 855 - Part 2 · Edition 5.1990 → current

Half-round profile cutter, concave · Technical delivery conditions

The information contained in the standard such as designation, dimensions, tolerances, material, design and marking apply to half-round profile milling cutters, concave according to DIN 855 Part 1.

DIN 855 - Part 2 · Edition 12.1981 → replaced by Edition 5.1990

Half-round profile cutter, concave · Technical delivery conditions

DIN 855 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Half-round profile cutter, concave · Technical delivery conditions

DIN 855 edition 2.1960 → withdrawn

Semicircular cutter · curved inwards

DIN 855 edition 8.1955 → withdrawn

Semicircular cutter · curved inwards

DIN 855 Edition 7.1926 → withdrawn

Concave semicircular form cutters

DIN 856 - Part 1 Edition 9.1978 → current

Half-round profile cutter, convex · Dimensions

DIN 856 - Part 2 · Edition 5.1990 → current

Half-round profile cutter, convex · Technical delivery conditions

The information contained in the standard such as designation, dimensions, tolerances, material, design and marking apply to semicircular profile milling cutters, convex according to DIN 856 Part 1.

DIN 856 - Part 2 · Edition 12.1981 → replaced by Edition 5.1990

Half-round profile cutter, convex · Technical delivery conditions

DIN 856 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Half-round profile cutter, convex · Technical delivery conditions

DIN 856 edition 8.1955 → withdrawn

Semicircular cutter · curved outwards

DIN 856 edition 7.1926 → withdrawn

Convex semicircular shape cutter

DIN 857 edition 3.1951 → current

Machine tools for metal · milling cutters · cutting direction, flute direction, longitudinal pressure

DIN 857 edition 8.1930 → withdrawn

Milling cutter · cutting direction, groove direction, longitudinal pressure

DIN 859 edition 12.2007 → current

Hand reamers with straight shank - adjustable, slotted

The standard specifies the dimensions for adjustable, slotted hand reamers with straight shank.

DIN 859 edition 12.1996 → replaced by edition 12.2007

Hand reamers with straight shank, adjustable, slotted

The specifications of the standard apply to hand reamers with straight shank, adjustable and slotted.

DIN 859 edition 9.1979 → replaced by edition 12.1996

Hand reamers with straight shank, adjustable, slotted

DIN 859 edition 9.1953 → withdrawn

Machine tools for metal · hand reamers · adjustable, slotted

DIN 859 edition 7.1926 → withdrawn

Hand reamers · adjustable, slotted

DIN 861 - Part 1 edition 1.1980 → replaced by DIN EN ISO 3650 edition 2.1999

Gauge blocks · Terms, requirements, testing

DIN 861 - Part 1 Edition 10.1959 → withdrawn

Gauge blocks · Terms, designs, permissible deviations

DIN 861 - Part 1 · Edition 5.1955 → withdrawn

Gauge blocks · Terms, design, permissible deviations

DIN 861 - Part 2 · Edition 5.1955 → withdrawn without replacement

Measuring jaws, gauge blocks · Terms, designs, permissible deviations

DIN 861 Edition 7.1927 → withdrawn

Gauge blocks · Terms, accuracy, design

DIN 862 Edition 3.2015 → current

Geometrical product specifications (GPS) · Caliper · Limit values ​​for measurement errors

The standard defines the limit values ​​for measurement errors and applies to calipers according to DIN EN ISO 13385 Part 1 with a scale display and a measuring range from 0 mm to 2000 mm with a scale division / vernier scale of 0.1 mm, 0.05 mm, 0.02 mm as well as for calipers with digital display with a measuring range up to 1000 mm and a step value of 0.01 mm The standard also applies to depth calipers in accordance with DIN EN ISO 13385 Part 2 with a measuring range from 0 mm to 600 mm and also for a measuring range from over 600 mm to 1000 mm with numeric and scale display.

DIN 862 edition 12.1988 → 12.2011 replaced by edition 3.2015, DIN EN ISO 13385 part 1 edition 12.2011 and DIN EN ISO 13385 part 2 edition 6.2013

Caliper · Requirements, testing

DIN 862 edition 3.1979 → replaced by edition 12.1988

Vernier caliper · Terms, requirements, testing

DIN 862 edition 12.1960 → withdrawn

Slide gauges · Terms, requirements, permissible deviations, testing

DIN 862 edition 12.1929x → withdrawn

Slide gauges (precision slide gauges)

Cross edition 11.1951

DIN 862 - Supplement · Edition 12.1929 → withdrawn

Slide gauges (precision slide gauges) · Accuracies

DIN 863 - Part 1 · Edition 2.2017 → current

Geometrical product specifications (GPS) · Micrometers · Outside micrometers · Limit values ​​for measurement errors

The standard contains the limit values ​​for measurement errors for outside micrometers. The limit values ​​are not part of the communication standard DIN EN ISO 3611.

DIN 863 - Part 1 · Edition 4.1999 → replaced by Edition 2.2017 and DIN EN ISO 3611 Edition 3.2011

Checking of geometric sizes · Micrometers · Micrometers, standard design · Terms, requirements, testing

The standard applies to outside micrometers in normal design (N) for dimensions up to 500 mm with a scale division or numerical value of 0.01 mm and a maximum measuring span of 25 mm. It defines the most important dimensional, functional and qualitative properties of outside micrometers and their testing.

DIN 863 - Part 1 edition 10.1983 → replaced by edition 4.1999

Micrometers · Micrometers, standard design · Terms, requirements, testing

DIN 863 - Part 1 · Edition 11.1977 → replaced by Edition 10.1983

Micrometers · Micrometers, terms, requirements, testing

DIN 863 - Part 2 · Edition 4.1999 → current

Testing of geometric sizes · Micrometers · Installation micrometers, depth micrometers · Terms, requirements, testing

The standard applies to built-in micrometers and depth micrometers with a scale division or numerical value of 0.01 mm and a maximum measuring span of 25 mm. It defines the most important dimensional, functional and qualitative properties of micrometers and depth micrometers and their testing.

DIN 863 - Part 2 · Edition 6.1981 → replaced by Edition 4.1999

Micrometers · Installation micrometers, depth micrometers · Terms, requirements, testing

DIN 863 - Part 3 · Edition 4.1999 → current

Testing of geometric sizes · Micrometers · Micrometers, special designs · Design features, requirements, testing

The standard applies to special versions of micrometers. It applies together with DIN 863 Part 1.

DIN 863 - Part 3 · Edition 10.1983 → replaced by Edition 4.1999

Micrometers · Outside micrometers, special designs · Design features, requirements, testing

DIN 863 - Part 4 · Edition 4.1999 → current

Testing of geometric sizes · Micrometers · Inside micrometers · Terms, requirements, testing

The standard applies to internal micrometers for dimensions up to 500 mm with a scale division or numerical value of 0.01 mm and a maximum measuring span of 25 mm. It defines the most important dimensional, functional and qualitative properties of internal micrometers and their testing.

DIN 863 - Part 4 · Edition 6.1981 → replaced by Edition 4.1999

Micrometers · Inside micrometers · Terms, requirements, testing

DIN 863 edition 2.1956 → withdrawn

Outside micrometers (micrometers) · Terms, requirements, permissible deviations, testing

DIN 863 edition 4.1928 → withdrawn

Screw gauges, manufacturing accuracy and bending

DIN 864 edition 10.1931 → withdrawn

Line rulers · Standard for comparison

DIN 865 edition 12.2006 → current

Geometrical product specification (GPS) · Line rules, test standards · Executions, requirements

The standard applies to line rules with a square cross-section and total pitch lengths of up to 2000 mm, which are used, among other things, to test working rules according to DIN 866.

DIN 865 edition 3.1983 → replaced by edition 12.2006

Line rules · Test rules · Requirements

DIN 865 edition 10.1931 → withdrawn

Line rulers · test scale

DIN 866 Edition 12.2006 → current

Geometrical product specification (GPS) · Line rules, working rules · Executions, requirements

The standard applies to steel rule rulers with a rectangular cross-section and total pitch lengths of up to 5000 mm, which are mainly used for mechanical production purposes.

DIN 866 edition 3.1983 → replaced by edition 12.2006

Line rules · Working rules · Executions, requirements

DIN 866 edition 10.1931 → withdrawn

Line Rulers · Working Rulers

DIN 867 edition 2.1986 → current

Reference profiles for involute gears on spur gears (cylindrical gears) for general mechanical engineering and heavy engineering

The standard provides rules for the reference profiles to be preferably used for involute gears of spur gears (cylindrical gears) for general mechanical engineering and heavy engineering. It is mainly used for spur gears according to DIN 3960 with modules m equal to 1 mm to 70 mm.

DIN 867 edition 9.1974 → replaced by edition 2.1986

Reference profile for spur gears (cylindrical gears) with involute teeth, for general mechanical engineering and heavy engineering

DIN 867 edition 9.1963 → withdrawn

Reference profile for spur gears with involute teeth for general mechanical engineering

DIN 867 Edition 7.1927 → withdrawn

Tooth shape for spur gears and bevel gears

DIN 868 Edition 12.1976 → current

General terms and determinants for gears, gear pairs and gear drives

DIN 868 edition 4.1929x → withdrawn

Gears · Terms, designations and symbols

Cross edition 1.1941

DIN 869 - Part 1 Issue 3.1931 → withdrawn

Gears · Guidelines for ordering spur gears

DIN 869 - Part 2 Edition 3.1931x → replaced by DIN 3966 Part 2

Gears · Guidelines for ordering bevel gears

Cross edition 7.1952

DIN 870 edition 3.1931 → withdrawn

Gears · Profile shift with involute gearing

DIN 872 Edition 3.1947 → replaced by DIN 820 Part 1

Standardization work

DIN 874 - Part 1 · Edition 11.2003 → current

Geometrical product specifications (GPS) · Rulers · Flat rulers made of steel · Dimensions, technical delivery conditions

The standard applies to flat rulers made of steel with a length of up to 5000 mm.

DIN 874 - Part 1 · Edition 8.1973 → replaced by Edition 11.2003

Rulers · Flat rulers made of steel · Dimensions, technical delivery conditions

DIN 874 - Part 2 · Edition 11.2003 → current

Geometrical product specifications (GPS) · Rulers · Straight rulers · Dimensions, technical delivery conditions

The standard applies to straight rules with a length of up to 1000 mm.

DIN 874 - Part 2 · Edition 8.1973 → replaced by Edition 11.2003

Rulers · Straight rulers · Dimensions, technical delivery conditions

DIN 874 - Part 3 Edition 1.2008 → current

Geometrical product specification (GPS) · Rulers · Flat rulers made of natural hard stone · Dimensions, technical delivery conditions

The standard applies to flat rulers made of natural hard stone with a length of up to 2000 mm and specifies the most important construction and measurement features and their testing.

DIN 874 edition 10.1931 → withdrawn

Steel rulers

DIN 875 - Part 1 Edition 7.2005 → current

Geometrical product specification (GPS) · Angle 90 ° · Steel angle 90 °

The standard applies to flat, stop and straight angles made of steel with an angle of 90 ° and a side length of up to 1500 mm. The standard specifies the most important design and metrological features and their testing.

DIN 875 - Part 2 · Edition 1.2008 → current

Geometrical product specifications (GPS) · 90 ° angle · 90 ° angle made of natural hard stone

The standard applies to flat angles made of natural hard stone with an angle of 90 ° and a leg length of up to 1000 mm and defines the most important construction and measurement features and their testing.

DIN 875 Edition 3.1981 → replaced by DIN 875 Part 1 Edition 7.2005

Steel angle 90 °

DIN 875 edition 8.1973 → withdrawn

90 ° angle · Dimensions, technical delivery conditions

DIN 875 edition 10.1931 → withdrawn

Steel angle

DIN 876 - Part 1 Edition 8.1984 → current

Test plates · Test plates made of natural hard stone · Requirements, testing

Test plates are used in length testing technology for a large number of dimension, form and position tests as the embodiment of a plane. This standard specifies the most important requirements for test plates made of natural hard stone and describes procedures for checking compliance with these requirements.

DIN 876 - Part 2 Edition 8.1984 → current

Test plates · Test plates made of cast iron · Requirements, testing

Test plates are used in length testing technology for a large number of dimension, form and position tests as the embodiment of a plane. This standard specifies the most important requirements for cast iron test panels and describes procedures for checking compliance with these requirements.

DIN 876 · edition 5.1972 → replaced by DIN 876 parts 1 and 2 edition 8.1984

Measuring plates made of cast iron and hard stone · Dimensions, technical delivery conditions

DIN 876 - Part 1 · Edition 6.1950 → withdrawn

Spotting Plates · Dimensions

DIN 876 - Part 2 Edition 10.1931x → withdrawn

Spotting Plates · Requirements

Cross edition 9.1955

DIN 877 Edition 6.1986 → current

Inclinometers (level scales)

The standard specifies requirements for inclinometers that contain either tubular levels or electronic measuring devices. These inclinometers are used to measure the inclination of objects with respect to the direction of gravity.

DIN 877 edition 5.1959 → replaced by edition 6.1986

Spirit levels · Terms, requirements, permissible deviations, testing

DIN 877 edition 10.1932 → withdrawn

Spirit levels (dragonflies)

DIN 878 edition 6.2006 → current

Geometrical Product Specifications (GPS) · Mechanical dial indicators · Limit values ​​for metrological features

The standard applies to mechanical dial gauges according to DIN EN ISO 463. It also defines the numerical values ​​for the limit values ​​for metrological features.

DIN 878 edition 10.1983 → replaced by edition 6.2006 and DIN EN ISO 463 edition 6.2006

Dial gauges

DIN 878 edition 1.1979 → replaced by edition 10.1983

Dial gauges

DIN 878 · Edition 6.1970 → withdrawn

Dial gauges

DIN 878 - Part 1 · Edition 6.1959 → withdrawn

Dial indicators · main dimensions and connection dimensions

DIN 878 - Part 1 · Edition 8.1943 → withdrawn

Dial gauges · Connection dimensions, execution

2nd edition of the standard

DIN 878 - Part 2 · Edition 12.1955 → withdrawn

Dial gauges · Terms, requirements, permissible deviations, testing

DIN 879 - Part 1 · Edition 6.1999 → current

Checking geometric quantities - dial indicator · With mechanical display

The standard applies to dial indicators with mechanical display without electrical limit contacts with scale divisions of 0.5; 1; 2; 5; 10; 50 mm and measuring spans of 0.05; 0.1; 0.2; 0.26; 0.5; 1.0 and 3.0 mm.

DIN 879 - Part 1 · Edition 10.1983 → replaced by Edition 6.1999

Precision pointer with mechanical display

DIN 879 - Part 1 · Edition 1.1979 → replaced by Edition 10.1983

Precision pointer with mechanical display

DIN 879 - Part 1 · Edition 5.1959 → withdrawn

Precision pointer (precision probe) with clamping shaft · Connection dimensions

DIN 879 - Part 2 · Edition 4.1961 → withdrawn

Precision pointer (precision probe) with clamping shank · Terms, requirements, permissible deviations, testing

DIN 879 - Part 3 · Edition 6.1999 → current

Checking geometric quantities - dial indicator · With mechanical display and electrical limit contacts

The standard applies to mechanical dial indicators with electrical limit contacts.

DIN 879 - Part 3 · Edition 11.1975 → replaced by Edition 6.1999

Dial indicator with electrical limit contacts

DIN 879 · Edition 6.1970 → withdrawn

Dial indicator with clamping shaft

DIN 879 edition 10.1943 → withdrawn

Fine probe for installation in measuring tables, stands or the like · Connection dimensions

DIN 881 edition 10.1947 → withdrawn

Burn-off and upsetting allowances for melt-butt welding of shank tools with high-speed steel (SS) cutting edges, guidelines

DIN 883 Edition 7.1943 → withdrawn

Shell end mill with driving groove according to DIN 138

DIN 884 - Part 1 Edition 6.1981 → 6.2017 withdrawn without replacement

Milling cutter · Dimensions

DIN 884 - Part 2 Edition 5.1990 → 6.2017 withdrawn without replacement

Milling cutter · Technical delivery conditions

The information contained in the standard such as designation, dimensions, tolerances, material, design and marking apply to plain milling cutters according to DIN 884 Part 1.

DIN 884 - Part 2 · Edition 12.1981 → replaced by Edition 5.1990

Milling cutter · Technical delivery conditions

DIN 884 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Milling cutter · Technical delivery conditions

DIN 884 edition 3.1951 → withdrawn

Machine tools for metal · Milling cutters

DIN 884 edition 7.1943 → withdrawn

Cylindrical milling cutter

DIN 885 - Part 1 · Edition 6.1981 → current

Side milling cutter · Dimensions

DIN 885 - Part 2 · Edition 5.1990 → current

Side milling cutters · Technical delivery conditions

The information contained in the standard such as designation, dimensions, tolerances, material, design and marking apply to side milling cutters according to DIN 885 Part 1.

DIN 885 - Part 2 · Edition 12.1981 → replaced by Edition 5.1990

Side milling cutters · Technical delivery conditions

DIN 885 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981

Side milling cutters · Technical delivery conditions

DIN 885 edition 3.1951x → withdrawn

Machine tools for metal · Side milling cutters

Cross edition 6.1957

DIN 885 Edition 7.1943 → withdrawn

Side milling cutter, cross-cut

DIN 886 - Part 1 Edition 11.1943 → withdrawn

Milling arbors with driver according to DIN 138

DIN 886 - Part 2 Edition 11.1943 → withdrawn

Milling arbors with driver according to DIN 138 · Milling screw

DIN 886 - Part 3 Edition 11.1943 → withdrawn

Milling arbors with driver according to DIN 138 · Nose wrench

DIN 887 edition 3.1951 → withdrawn without replacement

Machine tools for metal · Thread milling cutter · with parallel shank for metric threads

DIN 888 Edition 3.1951 → withdrawn without replacement

Machine tools for metal · Thread milling cutter · with Morse taper for metric threads

DIN 893 edition 1.1943 → withdrawn

Wrench · Head and Shank Dimensions

DIN 894 edition 9.2007 → current

Open-end wrenches for subordinate applications · Dimensions and test torques

This standard deals with single open-end wrenches for subordinate applications; it contains the dimensions and the designation of these keys.

DIN 894 edition 11.1982 → replaced by edition 9.2007

Open-end wrench · Test torques according to series D

DIN 894 edition 12.1967 → replaced by edition 11.1982

Open-end wrench · Test torques according to series D

DIN 894 edition 8.1957 → withdrawn

Open-ended spanners with test torques according to row D

DIN 894 edition 1.1943 → withdrawn

Single wrench

DIN 895 edition 9.2007 → current

Double open-end wrench for subordinate applications - dimensions and test torques

This standard deals with double open-end wrenches for use as equipment for vehicles; it contains the dimensions and the designation of these keys.

DIN 895 edition 1.1987 → replaced by edition 9.2007

Open-ended spanners with unequal widths across flats · Test torques according to series D

DIN 895 edition 4.1976 → replaced by edition 1.1987

Open-ended spanners with unequal widths across flats · Test torques according to series D

DIN 895 edition 12.1967 → replaced by edition 4.1976

Open-ended spanners with unequal widths across flats · Test torques according to series D

DIN 895 edition 8.1957x → withdrawn

Double open-end wrenches with unequal widths across flats and test torques according to row D

Cross edition 3.1961

DIN 895 edition 1.1943 → withdrawn

Double wrenches with unequal jaw widths

DIN 896 edition 10.2007 → current

Double socket wrench, solid and made of tube - dimensions and test torques according to row A

The standard deals with double socket wrenches; it contains the dimensions and the designation of these keys. The socket wrenches must meet the test torques row A according to DIN 899.

DIN 896 edition 1.1987 → replaced by edition 10.2007

Double socket wrench · Test torques according to row A

DIN 896 - Part 1 · Edition 4.1976 → replaced by DIN 896 Edition 1.1987

Double socket wrench, solid

DIN 896 - Part 1 · Edition 2.1968 → replaced by Edition 4.1976

Double socket wrench, solid

DIN 896 - Part 2 · Edition 4.1978 → replaced by DIN 896 Edition 1.1987

Double socket wrench made of pipe

DIN 896 - Part 2 · Edition 2.1968 → withdrawn

Double socket wrench made of pipe

DIN 896 Edition 6.1946 → withdrawn

Hexagon socket wrench, forged, made of tube

DIN 897 edition 11.2007 → current

Flat cranked double ring spanners Dimensions and test torques according to row A

The standard deals with flat cranked double ring spanners with unequal widths across flats and contains the dimensions and designation of these keys. The double ring spanners must meet the test torques series A and DIN ISO 1711-1.

DIN 897 edition 1.1987 → replaced by edition 11.2007

Flat cranked double ring spanners with unequal widths across flats · Test torques according to row A

The standard deals with flat cranked double ring spanners with unequal wrench sizes; it contains the dimensions and the designation of these keys. The double ring spanners must meet the test torques series A and DIN 899.

DIN 897 edition 4.1976 → replaced by edition 1.1987

Flat cranked double ring spanners with unequal widths across flats · Test torques according to row A

DIN 897 edition 12.1967 → replaced by edition 4.1976

Flat cranked double ring spanners with unequal widths across flats · Test torques according to row A

DIN 898 edition 5.2008 → current

Screwdriving tools overview, designations and names (ISO 1703: 2005, modified)

The standard contains the terms and designations of the international dictionary for screwdriving tools, which were defined by the ISO.

DIN 898 edition 6.1995 → replaced by edition 5.2008

Screwdriving tools · Overview, terms, terms

The standard contains the terms and designations of the international dictionary for screwdriving tools, which were defined by the ISO.

DIN 898 edition 4.1987 → replaced by edition 6.1995

Screwdriving tools · Overview, terms, terms

DIN 898 edition 10.1975 → replaced by edition 4.1987

Screwdriving tools · Overview, terms, terms

DIN 898 edition 5.1969 → withdrawn

Screw tools · Overview, terms, terms

DIN 899 edition 10.2001 → replaced by DIN ISO 1711 part 1 edition 5.2007

Wrenches · Technical delivery conditions for hand-operated wrenches

The standard applies to all hand-operated, non-adjustable wrenches and socket wrench inserts (with the exception of impact wrenches) whose key opening grips the screw head or nut on all sides or on at least two opposite sides.

DIN 899 edition 1.1980 → replaced by edition 10.2001

Wrenches · Technical delivery conditions for hand-operated wrenches

DIN 899 edition 1.1968 → withdrawn

Wrenches · Technical delivery conditions for hand-operated wrenches

DIN 899 edition 4.1957 → withdrawn

Wrenches · technical delivery conditions for forged non-adjustable open-end and ring spanners

DIN 900 edition 9.2008 → current

Screwdriving tools · Rotary pins for socket wrenches · Dimensions and design

The standard applies to rotary pins that are mainly used to operate socket wrenches according to DIN 896 and DIN 3112.

DIN 900 edition 8.1967 → replaced by edition 9.2008

Pivot pins for socket wrenches

DIN 900 edition 8.1944 → withdrawn

Pivot pins for socket wrenches

DIN 901 edition 8.1944 → withdrawn

Articulated socket wrench

DIN 902 edition 11.1982 → 1.1998 withdrawn without replacement

Single-ended spanner made of sheet steel

DIN 902 edition 12.1967 → replaced by edition 11.1982

Single-ended spanner made of sheet steel

DIN 904 edition 9.2007 → current

Square socket wrench

The standard deals with square socket wrenches that are used to operate the spindles of clamping claws for carousel lathes and three-jaw chucks as well as for operating square screws and switch cabinets and locking devices.

DIN 904 edition 8.1978 → replaced by edition 9.2007

Square socket wrench

DIN 904 edition 11.1967 → replaced by edition 8.1978

Square socket wrench

DIN 904 Edition 6.1937 → withdrawn

Square socket wrench

DIN 905 edition 7.2009 → current

Screwdriving tools · Screwdrivers for square socket screws · Dimensions and design

DIN 905 edition 8.1978 → replaced by edition 7.2009

Screwdriver for square socket screws

DIN 905 edition 10.1967 → replaced by edition 8.1978

Square socket wrench

DIN 905 · Edition 6.1937 → withdrawn

Square socket wrench

DIN 906 edition 4.2012 → current

Locking screws with internal drive · Tapered thread

The standard contains the dimensional specifications and technical delivery conditions for screw plugs with hexagon socket and specifies their designation.

DIN 906 edition 1.1992 → replaced by edition 4.2012

Screw plugs with hexagon socket · conical thread

DIN 906 edition 6.1983 → replaced by edition 1.1992

Screw plugs with hexagon socket · conical thread

DIN 906 edition 1.1973 → replaced by edition 6.1983

Locking screws with hexagon socket, conical thread

DIN 906 edition 4.1956 → withdrawn

Locking screws with hexagon socket · M10 × 1 cone, M12 × 1.5 cone to M52 × 1.5 cone, M27 × 2 cone to M60 × 2 cone and R 1/8 "cone to R 2" cone

taper = tapered thread

DIN 906 edition 12.1943 → withdrawn

Locking screws with hexagon socket M10 × 1 to M64 × 2

DIN 907 edition 6.1983 → withdrawn

Sealing plugs · Sealing plug rods · cylindrical thread

DIN 907 edition 1.1973 → replaced by edition 6.1983

Core plugs, core plug rods

DIN 907 edition 3.1964 → withdrawn

Core plug

The standard contains the dimensional specifications in accordance with ISO / R 272.

DIN 907 Edition 6.1942 → withdrawn

Core plugs M8 × 1 to M8 × 10, M12 × 1.5 to M48 × 1.5, M56 × 2 to M100 × 2

DIN 907 edition 4.1924 → withdrawn

Core plugs · Whitworth pipe threads

DIN 908 edition 4.2012 → current

Screw plugs with collar and internal drive · Cylindrical thread

The standard contains the dimensional specifications and technical delivery conditions for screw plugs with collar and hexagon socket and specifies their designation.

DIN 908 edition 1.1992 → replaced by edition 4.2012

Screw plugs with collar and hexagon socket · cylindrical thread

DIN 908 edition 6.1983 → replaced by edition 1.1992

Screw plugs with collar and hexagon socket · cylindrical thread

DIN 908 edition 1.1973 → replaced by edition 6.1983

Screw plugs with collar and hexagon socket, cylindrical thread

DIN 908 edition 9.1959 → withdrawn

Screw plugs with collar and hexagon socket · M10 × 1, M12 × 1.5 to M52 × 1.5, M27 × 2 to M64 × 2 and R 1/8 "to R 2"

DIN 908 edition 12.1943 → withdrawn

Screw plugs with collar with hexagon socket · M10 × 1 to M64 × 2

DIN 908 edition 4.1925 → withdrawn

Locking screws with elongated hole · Whitworth pipe thread

DIN 909 Edition 4.2012 → current

Locking screws with external hexagon · Tapered thread

The standard contains the dimensional specifications and technical delivery conditions for screw plugs with external hexagon and specifies their designation.

DIN 909 edition 1.1992 → replaced by edition 4.2012

Screw plugs with external hexagon · tapered thread

DIN 909 edition 6.1983 → replaced by edition 1.1992

Screw plugs with external hexagon · tapered thread

DIN 909 edition 1.1973 → replaced by edition 6.1983

Screw plugs with external hexagon, conical thread

DIN 909 edition 4.1956 → withdrawn

Locking screws with external hexagon · M10 × 1 cone, M12 × 1.5 cone to M52 × 1.5 cone, M27 × 2 cone to M60 × 2 cone and R 1/8 "cone to R 2" cone

taper = tapered thread

DIN 909 edition 12.1943 → withdrawn

Locking screws with external hexagon M10 × 1 to M64 × 2

DIN 910 · Edition 4.2012 → current

Screw plugs with collar and external hexagon · Cylindrical thread

The standard contains the dimensional specifications and technical delivery conditions for screw plugs with collar and external hexagon, heavy design and specifies their designation.

DIN 910 edition 1.1992 → replaced by edition 4.2012

Screw plugs with collar and hexagon head · heavy duty, cylindrical thread

DIN 910 - Part 1 · Edition 6.1983 → replaced by DIN 910 Edition 1.1992

Screw plugs with collar and hexagon head · heavy duty, cylindrical thread

DIN 910 - Part 1 · Edition 1.1973 → replaced by Edition 6.1983

Screw plugs with collar and external hexagon, heavy design, cylindrical thread

DIN 910 - Part 2 · Edition 1.1973 → replaced by DIN 5586 Edition 2.1989

Screw plugs with collar and hexagon head, heavy-duty design with vent hole, cylindrical thread

DIN 910 edition 9.1959 → withdrawn

Locking screws with collar and hexagon head, heavy-duty design · M10 × 1, M12 × 1.5 to M52 × 1.5, M27 × 2 to M64 × 2 and R 1/8 "to R 2"

DIN 910 - Part 1 Edition 12.1943 → withdrawn

Screw plugs with collar with external hexagon M10 × 1 to M64 × 2

DIN 910 - Part 2 · Edition 4.1925x → withdrawn

Screw plugs with collar with external hexagon · R 1/8 "to R 2"

Cross edition 1.1944

DIN 910 edition 4.1925 → withdrawn

Hexagon screw plugs · Whitworth pipe thread

DIN 911 edition 3.1987 → replaced by DIN ISO 2936 edition 6.1996

Offset screwdriver for hexagon socket screws

DIN 911 edition 9.1978 → replaced by edition 3.1987

Offset screwdriver for hexagon socket screws

DIN 911 · Edition 1.1968 → withdrawn

Hexagon screwdriver angled

DIN 911 · Edition 3.1944 → withdrawn

Allen key

DIN 911 · Edition 10.1933 → withdrawn

Allen key

DIN 912 edition 12.1983 → replaced by DIN EN ISO 4762 edition 2.1998

Hexagon socket head cap screws, ISO 4762 modified

DIN 912 edition 9.1979 → replaced by edition 12.1983

Hexagon socket head cap screws, ISO 4762 modified

DIN 912 - Part 2 Edition 10.1969 → withdrawn

Hexagon socket head cap screws M1.4 to M2.5

DIN 912 - supplement 1 edition 11.1970 → withdrawn

Socket head cap screws M3 to M48

DIN 912 edition 3.1961 → withdrawn

Hexagon socket head cap screws (hexagon socket screws) M4 to M48, M8 × 1 and M10 × 1, M12 × 1.5 to M16 × 1.5, M18 × 2 to M33 × 2, M36 × 3 to M48 × 3

DIN 912 edition 7.1953 → withdrawn

Cylinder screws with hexagon socket

DIN 912 edition 4.1946 → withdrawn

Allen screws M4 to M48, M8 × 1 to M48 × 3, version w

DIN 912 edition 10.1933 → withdrawn

Bare cylinder screws with hexagon socket

DIN 913 edition 12.1980 → replaced by DIN EN ISO 4026 edition 5.2004

Grub screws · with hexagon socket and tapered point, ISO 4026 modified

DIN 913 edition 1.1973 → withdrawn

Grub screws · with hexagon socket and tapered point

DIN 913 edition 9.1959 → withdrawn

Set screws and set screws with hexagon socket and tapered point · M3 to M24 and M20 × 2 to M24 × 2

DIN 913 Edition 6.1953 → withdrawn

Grub screws, set screws · with hexagon socket and tapered point

DIN 913 edition 2.1948 → withdrawn

Grub screws, set screws · with hexagon socket and conical shoulder · M6 to M24

DIN 913 edition 10.1933 → withdrawn

Grub screws, set screws · with hexagon socket and tapered shoulder

DIN 914 edition 12.1980 → replaced by DIN EN ISO 4027 edition 5.2004

Grub screws · with hexagon socket and point, ISO 4027 modified

DIN 914 edition 1.1973 → withdrawn

Grub screws · with hexagon socket and point

DIN 914 edition 9.1959 → withdrawn

Set screws and set screws with hexagon socket and point · M3 to M24 and M20 × 2 to M24 × 2

DIN 914 edition 6.1953 → withdrawn

Grub screws, set screws · with hexagon socket and point

DIN 914 edition 1.1948 → withdrawn

Grub screws, set screws · with hexagon socket and point · M6 to M24

DIN 914 edition 10.1933 → withdrawn

Grub screws · with hexagon socket and point

DIN 915 edition 12.1980 → replaced by DIN EN ISO 4028 edition 5.2004

Grub screws · with hexagon socket and tenon, ISO 4028 modified

DIN 915 edition 1.1973 → replaced by edition 12.1980

Grub screws · with hexagon socket and tenon

DIN 915 edition 9.1959 → withdrawn

Set screws and set screws with hexagon socket and spigot · M3 to M24 and M20 × 2 to M24 × 2

DIN 915 · Edition 6.1953 → withdrawn

Grub screws, set screws · with hexagon socket and pin

DIN 915 edition 1.1948 → withdrawn

Grub screws, set screws · with hexagon socket and spigot · M6 to M24

DIN 915 edition 10.1933 → withdrawn

Grub screws · with hexagon socket and tenon

DIN 916 edition 12.1980 → replaced by DIN EN ISO 4029 edition 5.2004

Grub screws · with hexagon socket and cup point, ISO 4029 modified

DIN 916 edition 1.1973 → withdrawn

Grub screws · with hexagon socket and cup point

DIN 916 edition 9.1959 → withdrawn

Set screws and set screws with hexagon socket and cup point · M3 to M24 and M20 × 2 to M24 × 2

DIN 917 edition 8.2015 → current

Hexagon cap nuts, low shape

The standard contains the dimensional specifications and technical delivery conditions for hexagon cap nuts, low form in sizes M4 to M72 and specifies their designation.

DIN 917 edition 10.2000 → replaced by edition 8.2015

Hexagon cap nuts, low shape

DIN 917 edition 2.2000 → replaced by edition 10.2000

Hexagon cap nuts, low shape

DIN 917 edition 6.1987 → replaced by edition 2.2000

Hexagon cap nuts, low shape

DIN 917 · edition 4.1977 → replaced by edition 6.1987

Hexagon cap nuts, low shape

DIN 917 edition 12.1970 → withdrawn

Cap nuts, low shape

DIN 917 - Part 1 Edition 10.1953 → withdrawn

Cap nut, low shape M4 to M64 and M8 × 1 to M10 × 1, M12 × 1.5 to M16 × 1.5, M18 × 2 to M30 × 2, M36 × 3 to M48 × 3, M56 × 4 to M72 × 4

DIN 917 - Part 1 · Edition 4.1942 → withdrawn

Cap nuts, low M4 to M72, version w

DIN 917 - Part 2 · Edition 5.1932x → withdrawn

Cap nut, low form 1/2 "to 3"

Cross edition 3.1942

DIN 917 · Edition 5.1932 → withdrawn

Low cap nuts

DIN 918 edition 8.2016 → current

Mechanical fasteners · Term, spelling of designations, abbreviations

DIN 918 edition 9.1979 → replaced by edition 8.2016

Mechanical fasteners · Term, spelling of designations, abbreviations

DIN 918 - supplement 1 edition 11.1987 → withdrawn

Mechanical connecting elements · Representation and names of standardized connecting elements

The attached sheet lists the representations and names of standardized connecting elements.

DIN 918 - supplement 1 edition 5.1982 → replaced by edition 11.1987

Mechanical fasteners · Representations and names of standardized fasteners

DIN 918 - Supplement 2 Edition 10.1991 → withdrawn

Mechanical fasteners · ISO standards and DIN standards · Overview

The supplementary sheet lists the comparable DIN standards for the ISO standards on mechanical connecting elements. This comparability is indicated by code letters.

DIN 918 - supplement 2 edition 11.1987 → replaced by edition 10.1991

Mechanical fasteners · ISO standards and DIN standards · Overview

DIN 918 - Supplement 2 · Edition 4.1985 → replaced by Edition 11.1987

Mechanical fasteners · ISO standards and DIN standards · Overview

DIN 918 - Supplement 3 · Edition 1.2010 → current

Mechanical fasteners · European standards · Overview

The supplement contains all the European standards on mechanical fasteners published on the cut-off date. The earlier national standards, which have since been withdrawn, are compared to the European standards.

DIN 918 - supplement 3 edition 1.2005 → replaced by edition 1.2010

Mechanical fasteners · European standards · Overview

DIN 918 - supplement 3 edition 4.2001 → replaced by edition 1.2005

Mechanical fasteners · European standards · Overview

DIN 918 - supplement 3 edition 1.1999 → replaced by edition 4.2001

Mechanical fasteners · European standards · Overview

DIN 918 - Supplement 3 edition 4.1995 → replaced by edition 1.1999

Mechanical fasteners · European standards · Overview

DIN 918 - supplement 4 edition 4.1968 → withdrawn

Screws, nuts and accessories · Names of the types of nuts

DIN 918 - Part 1 · Edition 4.1968 → withdrawn

Screws, nuts and accessories · General terms

DIN 918 - Part 1 Edition 11.1924 → withdrawn

Bolts and nuts · Terms

DIN 918 - Part 2 · Edition 4.1968 → withdrawn

Screws, nuts and accessories · Dimensional notation

DIN 918 - Part 2 Edition 11.1924 → withdrawn

Bolts and nuts · Terms

DIN 918 - Part 3 · Edition 4.1968 → withdrawn

Bolts, nuts and accessories · Names of the types of bolts

DIN 918 - Part 3 Edition 11.1924 → withdrawn

Bolts and nuts · Terms

DIN 918 - Part 5 · Edition 4.1968 → withdrawn

Bolts, nuts and accessories · Names of accessories

DIN 919 - Part 1 · Edition 8.2014 → current

Technical drawings · Wood processing · Basics

The standard contains the basics for technical drawings of wood processing, such as for the planning and manufacture of furniture, windows and interior fittings.

DIN 919 - Part 1 - Supplement 1 Edition 6.1991 → replaced by DIN 919 Part 1 Edition 8.2014

Technical drawings · Wood processing · Basics · Application examples

To facilitate the application of DIN 919 Part 1, the supplement has been compiled with explanations of the cited standards and numerous drawing examples.

DIN 919 - Part 1 - Supplement 1 · Edition 4.1991 → replaced by Edition 6.1991

Technical drawings · Wood processing · Basics · Application examples

DIN 919 - Part 1 · Edition 4.1991 → replaced by Edition 8.2014

Technical drawings · Wood processing · Basics

Basics; The standard contains the basics for technical drawings of wood processing.

DIN 919 - Part 1 · Edition 8.1986 → replaced by Edition 4.1991

Technical drawings for wood processing · Basics

DIN 919 - Part 1 · Edition 3.1972 → replaced by Edition 8.1986

Technical drawings for wood processing · Basics

DIN 919 - Part 1 Edition 10.1958 → withdrawn

Wood products, wooden parts · technical drawings for production

DIN 919 - Part 2 Edition 3.1972 → replaced by DIN 919 Part 1 Edition 8.1986

Technical drawings for wood processing · Series production

DIN 919 edition 7.1949x → withdrawn

Drawings · Carpenters' drawings

2nd edition of the standard. Cross edition 1.1952

DIN 919 edition 1.1939 → replaced by edition 7.1949

Drawings · Carpenters' drawings

1st edition of the standard

DIN 920 · Edition 6.2012 → current

Flat head screws with slot and small head

This standard contains the dimensional specifications and the technical delivery conditions for flat head screws with slotted and small head, thread sizes M1 to M10, and specifies their designation.

DIN 920 edition 8.2006 → replaced by edition 6.2012

Flat head screws with slot and small head

DIN 920 edition 9.1986 → replaced by edition 8.2006

Flat head screws with slot and small head

DIN 920 edition 8.1972 → replaced by edition 9.1986

Flat head screws with slot and small head

DIN 920 edition 8.1953 → withdrawn

Pan head screws with longitudinal slot and small head · M1 to M10

DIN 920 edition 1.1943 → withdrawn

Small head pan head screws · M1 to M10

DIN 921 edition 11.2014 → current

Flat head screws with slot and large head

The standard specifies the properties of slotted pan head screws with a large head, sizes M1 to M10.

DIN 921 edition 1.2007 → replaced by edition 11.2014

Flat head screws with slot and large head

This standard contains the dimensional specifications and the technical delivery conditions for flat head screws with slot and large head and specifies their designation.

DIN 921 edition 8.2006 → replaced by edition 1.2007

Flat head screws with slot and large head

DIN 921 edition 9.1986 → replaced by edition 8.2006

Flat head screws with slot and large head

The standard contains the dimensional specifications and the technical delivery conditions for flat head screws with slot and large head and specifies their designation.

DIN 921 edition 8.1972 → replaced by edition 9.1986

Flat head screws with slot and large head

DIN 921 edition 2.1954 → withdrawn

Pan head screws with longitudinal slot and large head · M1 to M10

DIN 921 edition 1.1943 → withdrawn

Large head pan head screws M1 to M10

DIN 922 Edition 6.2012 → current

Slotted pan head screws with small head and tenons

This standard contains the dimensional specifications and the technical delivery conditions for flat head screws with slot, small head and tenon and specifies their designation.

DIN 922 edition 8.2006 → replaced by edition 6.2012

Slotted pan head screws with small head and tenons

DIN 922 edition 9.1986 → replaced by edition 8.2006

Slotted pan head screws with small head and tenons

DIN 922 Edition 8.1972 → replaced by Edition 9.1986

Slotted pan head screws with small head and tenons

DIN 922 edition 8.1953 → withdrawn

Pan head screws with longitudinal slot and tenon · M1.4 to M10

DIN 922 edition 1.1943 → withdrawn

Pan head screws · M1.4 to M10

DIN 923 edition 6.2012 → current

Flat head screws with slot and shoulder

This standard contains the dimensional specifications and the technical delivery conditions for flat head screws with slot and shoulder and specifies their designation.

DIN 923 edition 8.2006 → replaced by edition 6.2012

Flat head screws with slot and shoulder

DIN 923 edition 9.1986 → replaced by edition 8.2006

Flat head screws with slot and shoulder

DIN 923 Edition 8.1972 → replaced by Edition 9.1986

Flat head screws with slot and shoulder

DIN 923 edition 8.1953 → withdrawn

Pan head screws with longitudinal slot and shoulder · M1.4 to M10

DIN 923 edition 1.1943 → withdrawn

Pan-head screws with shoulder · M1.4 to M10

DIN 924 Edition 6.2012 → current

Raised countersunk head screws with slot and tenon

The standard specifies the properties of raised countersunk head screws with slot and tenon for thread sizes M1.4 to M3.

DIN 924 edition 8.2006 → replaced by edition 6.2012

Raised countersunk head screws with slot and tenon

DIN 924 edition 9.1986 → replaced by edition 8.2006

Raised countersunk head screws with slot and tenon

DIN 924 edition 8.1972 → replaced by edition 9.1986

Raised countersunk head screws with slot and tenon

DIN 924 edition 8.1953 → withdrawn

Raised countersunk head screws with tenons · M1.4 to M10

DIN 924 edition 1.1943 → withdrawn

Raised countersunk head screws with tenons · M1.4 to M10

DIN 925 · Edition 6.2012 → current

Countersunk screws with slot and tenon

The standard specifies the properties of countersunk head screws with slot and tenon for thread sizes M1.4 to M3.

DIN 925 edition 8.2006 → replaced by edition 6.2012

Countersunk screws with slot and tenon

DIN 925 edition 9.1986 → replaced by edition 8.2006

Countersunk screws with slot and tenon

DIN 925 edition 8.1972 → replaced by edition 9.1986

Countersunk screws with slot and tenon

DIN 925 edition 8.1953 → withdrawn

Countersunk screws with tenons · M1.4 to M10

DIN 925 edition 1.1943 → withdrawn

Countersunk screws with tenons · M1.4 to M10

DIN 926 edition 9.1986 → 3.2006 withdrawn without replacement

Grub screws with slot and tenon

DIN 926 edition 8.1972 → replaced by edition 9.1986

Grub screws with slot and tenon

DIN 926 edition 8.1953 → withdrawn

Grub screws with pin · M1 to M10

DIN 926 edition 1.1943 → withdrawn

Grub screws with pin · M1 to M10

DIN 927 Edition 6.2012 → current

Mortise pins with thread and slot

The standard specifies the properties of threaded and slot pins for thread sizes M1 to M6.

DIN 927 edition 8.2006 → replaced by edition 6.2012

Mortise pins with thread and slot

DIN 927 edition 9.1986 → replaced by edition 8.2006

Tenoning screws with slot

DIN 927 edition 8.1972 → replaced by edition 9.1986

Tenoning screws with slot

DIN 927 edition 8.1953 → withdrawn

Studs M1 to M10

DIN 927 edition 1.1943 → withdrawn

Studs M1 to M10

DIN 928 Edition 12.2013 → current

Square weld nuts

The standard specifies requirements for square weld nuts.

DIN 928 edition 5.2013 → replaced by edition 12.2013

Square weld nuts

DIN 928 edition 1.2000 → replaced by edition 5.2013

Square weld nuts

DIN 928 edition 2.1998 → replaced by edition 1.2000

Square weld nuts

DIN 928 edition 8.1983 → replaced by edition 2.1998

Square weld nuts

DIN 928 edition 5.1970 → replaced by edition 8.1983

Square weld nuts

DIN 929 edition 12.2013 → current

Hexagon weld nuts

The standard specifies requirements for hexagon weld nuts.

DIN 929 edition 5.2013 → replaced by edition 12.2013

Hexagon weld nuts

DIN 929 edition 1.2000 → replaced by edition 5.2013

Hexagon weld nuts

DIN 929 edition 2.1998 → replaced by edition 1.2000

Hexagon weld nuts

DIN 929 edition 9.1987 → replaced by edition 2.1998

Hexagon weld nuts

DIN 929 edition 8.1983 → replaced by edition 9.1987

Hexagon weld nuts

DIN 929 edition 12.1972 → replaced by edition 8.1983

Hexagon weld nuts

DIN 930 edition 1.1926 → withdrawn

Thread lengths for bare screws

DIN 931 - Part 2 · Edition 6.2009 → current

Hexagon head bolts with shank · Metric thread M68 to M160 × 6 · Product class B

DIN 931 - Part 2 · Edition 9.1987 → replaced by Edition 6.2009

Hexagon head bolts with shank · thread M42 to M160 × 6 · product class B

DIN 931 - Part 2 · Edition 7.1982 → replaced by Edition 9.1987

Hexagon head bolts with shank · thread M42 to M160 × 6 · product class B

DIN 931 - supplement 1 edition 9.1986 → withdrawn

Hexagon head bolts with shaft · Weights

DIN 931 - Part 1 edition 9.1987 → replaced by DIN EN 24014 edition 2.1992

Hexagon head bolts with shank · Thread M1.6 to M39 · Product classes A and B

DIN 931 - Part 1 Edition 7.1982 → replaced by Edition 9.1987 and DIN ISO 4014

Hexagon head bolts with shank · Thread M1.6 to M39 · Product classes A and B, ISO 4014 modified

DIN 931 edition 11.1970 → replaced by DIN 931 parts 1 and 2 edition 7.1982

Hexagon head bolts · Metric thread · Version m and mg

DIN 931 - Part 1 · Edition 12.1952 → withdrawn

Hexagon head screws M1.7 to M68 and M72 × 6 to M150 × 6 Version m and mg

DIN 931 - Part 1 · Edition 4.1942 → withdrawn

Hexagon head screws M1.7 to M10, version w

DIN 931 - Part 2 · Edition 4.1942 → withdrawn

Hexagon head screws M12 to M150, versions m and mg

DIN 931 - Part 3 · Edition 5.1954 → withdrawn

Hexagon head bolts · 1/4 "to 2" · Version m and mg

DIN 931 - Part 3 · Edition 1.1926x → withdrawn

Hexagon head bolts · for 1 nut or 1 castle nut · 1/2 "to 2", version m

DIN 932 - Part 3 · Edition 1.1926 → withdrawn

Hexagon head bolts · for 2 nuts · 1/4 "to 2", version with

DIN 933 edition 9.1987 → replaced by DIN EN 24017 edition 2.1992

Hexagon head screws with thread up to head · Thread M1.6 to M52 · Product classes A and B

DIN 933 edition 12.1983 → replaced by edition 9.1987 and DIN ISO 4017

Hexagon head bolts with thread up to head · Thread M1.6 to M52 · Product classes A and B, ISO 4017 modified

DIN 933 edition 12.1970 → replaced by edition 12.1983

Hexagon head screws · Thread almost up to the head · Metric thread, versions m and mg

DIN 933 - Part 1 Edition 12.1952 → withdrawn

Hexagon head screws, thread almost up to head · M1.7 to M52 · Version m and mg

DIN 933 - Part 1 · Edition 4.1942 → withdrawn

Hexagon head screws, thread almost up to head · M1.7 to M10 · Version m

DIN 933 - Part 2 · Edition 4.1942 → withdrawn

Hexagon head screws, thread almost up to the head · M12 to M52 · Version m and mg

DIN 933 - Part 3 · Edition 6.1954 → withdrawn

Hexagon head bolts, thread approximately to head · 1/4 "to 2" · Version m and mg

DIN 933 - Part 3 · Edition 7.1926 → withdrawn

Hexagon head bolts, thread to head · 1/4 "to 2" · Version with

DIN 934 edition 10.1987 → replaced by DIN EN 24032 and DIN EN 28673 edition 2.1992 and DIN ISO 8673 edition 1.1990

Hexagon nuts · Metric standard and fine threads · Product classes A and B

DIN 934 edition 7.1982 → replaced by edition 10.1987

Hexagon nuts · Metric threads · Product grades A and B

DIN 934 edition 4.1968 → replaced by edition 7.1982

Hexagon nuts · Metric thread, metric fine thread, versions m and mg

DIN 934 - Part 1 Issue 3.1961 → withdrawn

Hexagon nuts M1 to M68, M8 × 1 and M10 × 1, M12 × 1.5 to M52 × 1.5, M18 × 2 to M125 × 2, M36 × 3 to M150 × 3, M56 × 4 to M125 × 4 and M72 × 6 to M150 × 6 · m and mg versions

DIN 934 - Part 1 · Edition 6.1953 → withdrawn

Hexagon nuts · Metric thread, metric fine thread, versions m and mg

DIN 934 - Part 1 · Edition 4.1942 → withdrawn

Hexagon nuts M1.7 to M150, M8 × 1 to M150 × 4, versions m and mg

DIN 934 - part 2 edition 8.1954 → withdrawn

Hex nuts · 1/4 "to 6" and W 20 × 1/10 "to W 33 × 1/10", W 36 × 1/8 "to W 52 × 1/8", W 56 × 1/6 "to W. 154 × 1/6 ", W 68 × 1/4" to W 99 × 1/4 "and R 1/4" to R 5 1/2 "· m and mg versions

DIN 934 - Part 2 · Edition 6.1937x → withdrawn

Hexagon nuts 1/2 "to 6", W 68 × 1/4 "to W 99 × 1/4", W 20 × 1/10 "to W 154 × 1/6", R 1/4 "to R 5 1/2 ", version w

DIN 934 edition 10.1934 → withdrawn

Bare Hex Nuts · Metric threads, Metric fine threads 3, Whitworth, Whitworth fine and Whitworth pipe threads

DIN 935 - Part 1 · Edition 8.2013 → current

Hexagon castle nuts · Metric standard and fine threads, product classes A and B

The standard specifies requirements for hexagon castle nuts with nominal thread diameters of 4 mm to 100 mm.

DIN 935 - Part 1 edition 10.2000 → replaced by edition 8.2013

Castle nuts · Metric standard and fine threads · Product classes A and B

DIN 935 - Part 1 · Edition 2.2000 → replaced by Edition 10.2000

Castle nuts · Metric standard and fine threads · Product classes A and B

DIN 935 - Part 1 · Edition 10.1987 → replaced by Edition 2.2000

Castle nuts · Metric standard and fine threads · Product classes A and B

DIN 935 - Part 1 · Edition 12.1983 → replaced by Edition 10.1987

Castle nuts · Metric thread · Product grades A and B

DIN 935 - Part 1 · Edition 5.1956 → withdrawn

Castle nuts M4 to M68, M8 × 1 and M10 × 1, M12 × 1.5 to M52 × 1.5, M18 × 2 to M100 × 2, M36 × 3 to M52 × 3, M56 × 4 to M100 × 4 Execution m

DIN 935 - Part 1 · Edition 2.1954 → withdrawn

Castle nuts · Metric thread, metric fine thread, version with

DIN 935 - Part 1 · Edition 4.1942x → withdrawn

Castle nuts M4 to M100, M8 × 1 to M100 × 4, version with

DIN 935 - Part 1 · Edition 4.1934 → withdrawn

Castle nuts metric thread and metric fine thread 3

DIN 935 - Part 2 · Edition 8.1954 → withdrawn

Castle nuts 1/4 "to 4" and W 20 × 1/10 "to W 33 × 1/10", W 36 × 1/8 "to W 52 × 1/8", W 56 × 1/6 "to W. 99 × 1/6 ", W 68 × 1/4" to W 99 × 1/4 "and R 1/4" to R 3 1/2 "· Version with

DIN 935 - Part 2 · Edition 6.1937x → withdrawn

Castle nuts 1/4 "to 4", W 68 × 1/4 "to W 99 × 1/4", W 20 × 1/10 "to W 99 × 1/6", R 1/4 "to R 3 1/2 "· Version w

DIN 935 - Part 2 · Edition 4.1934 → withdrawn

Castle nuts · Whitworth, Whitworth Fine and Whitworth pipe threads

DIN 935 - Part 3 · Edition 8.2013 → current

Hexagon castle nuts · Metric standard thread · Product class C

The standard specifies requirements for hexagon castle nuts of sizes M12 to M33.

DIN 935 - part 3 edition 10.2000 → replaced by edition 8.2013

Castle nuts · Metric standard thread · Product class C

DIN 935 - Part 3 · Edition 2.2000 → replaced by Edition 10.2000

Castle nuts · Metric standard thread · Product class C

DIN 935 - Part 3 · Edition 10.1987 → replaced by Edition 2.2000

Castle nuts · Metric standard thread · Product class C

DIN 935 - Part 3 · Edition 12.1983 → replaced by Edition 10.1987

Castle nuts · Metric thread · Product class C

DIN 935 - Edition 4.1977 → replaced by DIN 935 Part 1 and 3 Edition 12.1983

Castle nuts

DIN 935 · Edition 5.1968 → withdrawn

Castle nuts · Metric thread, metric fine thread, versions m, mg and g

DIN 936 edition 2.1985 → 3.1994 withdrawn without replacement

Flat hexagon nuts · threads M8 to M52 and M8 × 1 to M52 × 3 · product classes A and B

DIN 936 edition 11.1976 → replaced by edition 2.1985

Hexagon nuts, low shape (old version)

DIN 936 edition 6.1968 → replaced by edition 11.1976

Flat hexagon nuts · Metric thread, metric fine thread, versions m and mg

DIN 936 edition 10.1959 → withdrawn

Flat hexagon nuts M12 to M30, M8 × 1 to M10 × 1, M12 × 1.5 to M52 × 1.5, M18 × 2 to M33 × 2 and M36 × 3 to M52 × 3

DIN 936 edition 1.1954 → withdrawn

Flat hex nuts · Metric thread, Metric fine thread

DIN 936 edition 4.1946 → withdrawn

Hexagon nuts, flat · M12 to M30, M8 × 1 to M52 × 1.5, versions m and mg

DIN 937 edition 12.1983 → 8.1998 withdrawn without replacement

Castle nuts, low shape (old type)

DIN 937 edition 12.1978 → replaced by edition 12.1983

Castle nuts, low shape (old type)

DIN 937 edition 6.1963 → replaced by edition 12.1978

Flat castle nuts · Metric thread, Metric fine thread

DIN 937 edition 9.1959 → withdrawn

Flat castle nuts M6 to M30, M8 × 1 to M10 × 1, M12 × 1.5 to M52 × 1.5, M18 × 2 to M33 × 2 and M36 × 3 to M52 × 3

DIN 937 edition 3.1954 → withdrawn

Flat castle nuts · Metric thread, Metric fine thread

DIN 937 edition 4.1942 → withdrawn

Castle nuts, flat M6 to M30, M8 × 1 to M52 × 1.5, m version

DIN 938 edition 12.2012 → current

Studs · screw-in end ≈ 1 d

The standard specifies studs with thread sizes M3 to M52 and fine thread sizes M8x1 to M52x3, with a screw-in thread length of approximately 1 d.

DIN 938 edition 3.2012 → replaced by edition 12.2012

Studs · screw-in end ≈ 1 d

DIN 938 edition 2.1995 → replaced by edition 3.2012

Studs · screw-in end ≈ 1d

DIN 938 edition 12.1972 → replaced by edition 2.1995

Studs · screw-in end ≈ 1d

DIN 938 - Part 1 · Edition 3.1953 → withdrawn

Studs · screw-in end ≈ 1 d, for screwing into steel · with the same thread on both sides · M3 to M52 and M18 × 2 to M33 × 2, M36 × 3 to M52 × 3

DIN 938 - Part 1 · Edition 9.1951 → withdrawn

Studs · screw-in end ≈ 1 d, for screwing into steel · metric thread

DIN 938 - Part 1 · Edition 12.1943 → withdrawn

Studs · screw-in end ≈ 1 d, for screwing into steel · M3 to M52

DIN 938 - Part 1 · Edition 1.1926 → withdrawn

Bare studs · for 1 nut or 1 castle nut from M 3 to M 10, screw-in end 1 d

For screwing into steel, cast steel and bronze

DIN 938 - Part 2 · Edition 1.1926 → withdrawn

Bare studs · for 1 nut or 1 castle nut from M 11 to M 52, screw-in end 1 d

For screwing into steel, cast steel and bronze

DIN 938 - Part 3 · Edition 1.1956 → withdrawn

Studs · screw-in end ≈ 1 d, for screwing into steel · with the same thread on both sides · 1/4 "to 2"

DIN 938 - Part 3 · Edition 1.1926 → withdrawn

Bare studs · for 1 nut or 1 castle nut from 1/4 "to 2", screw-in end 1 d

For screwing into steel, cast steel and bronze

DIN 939 edition 2.1995 → current

Studs · screw-in end ≈ 1.25d

DIN 939 edition 12.1972 → replaced by edition 2.1995

Studs · screw-in end ≈ 1.25d

DIN 939 - Part 1 Edition 11.1953 → withdrawn

Studs · screw-in end ≈ 1.25 d, for screwing into gray cast iron · with the same thread on both sides · M3 to M52 and M18 × 2 to M33 × 2, M36 × 3 to M52 × 3, M56 × 4 to M120 × 4, M130 × 6 up to M150 × 6

DIN 939 - Part 1 · Edition 9.1951 → withdrawn

Studs · for 1 nut or 1 castle nut, screw-in end ≈ 1.25 d, for screwing into gray cast iron · Metric thread

DIN 939 - Part 1 Edition 12.1943 → withdrawn

Studs · screw-in end ≈ 1.25 d, for screwing into gray cast iron · M3 to M52

DIN 939 - Part 1 · Edition 1.1926 → withdrawn

Bare studs · for 1 nut or 1 castle nut from M 3 to M 10, screw-in end 1.3 d

For screwing into gray cast iron

DIN 939 - Part 2 · Edition 1.1926 → withdrawn

Bare studs · for 1 nut or 1 castle nut from M 11 to M 52, screw-in end 1.3 d

For screwing into gray cast iron

DIN 939 - Part 3 Edition 12.1955x → withdrawn

Studs · screw-in end ≈ 1.25 d, for screwing into gray cast iron · with the same thread on both sides · 1/4 "to 2"

Cross edition 12.1956

DIN 939 - Part 3 · Edition 1.1926 → withdrawn

Bare studs · for 1 nut or 1 castle nut from 1/4 "to 2", screw-in end 1.3 d

For screwing into gray cast iron

DIN 940 edition 7.2010 → current

Studs · screw-in end 2.5 d

The standard specifies dimensions, technical delivery conditions and the designation for studs with thread sizes M4 to M24 and fine thread sizes M8 × 1 to M24 × 2 with a screw-in thread length of approximately 2.5 d.

DIN 940 edition 2.1995 → replaced by edition 7.2010

Studs · screw-in end ≈ 2.5 d

DIN 940 edition 3.1983 → replaced by edition 2.1995

Studs · screw-in end ≈ 2.5 d

DIN 940 - Part 1 · Edition 12.1955 → withdrawn

Studs · screw-in end ≈ 2.5 d for screwing into soft metal · with the same thread on both sides · metric thread

DIN 940 - Part 1 · Edition 2.1954 → withdrawn

Studs · screw-in end ≈ 2.5 d for screwing into soft metal · with the same thread on both sides · metric thread

DIN 940 - Part 1 · Edition 2.1948 → withdrawn

Studs · screw-in end ≈ 2.5 d for screwing into soft metal · M3 to M52

DIN 940 - Part 1 · Edition 1.1926 → withdrawn

Bare studs · for 1 nut or 1 castle nut from M 3 to M 10, screw-in end 2.5 d

For screwing into soft metal

DIN 940 - Part 2 · Edition 1.1926 → withdrawn

Bare studs · for 1 nut or 1 castle nut from M 12 to M 30, screw-in end 2.5 d

For screwing into soft metal

DIN 940 - Part 3 · Edition 1.1956 → withdrawn

Studs · screw-in end ≈ 2.5 d, for screwing into soft metal · with the same thread on both sides · 1/4 "to 2"

DIN 940 - Part 3 · Edition 1.1926 → withdrawn

Studs · for 1 nut or 1 castle nut, screw-in end ≈ 2.5 d, for screwing into soft metal · 1/4 "to 2"

DIN 940 - Part 3 · Edition 1.1926 → withdrawn

Bare studs · for 1 nut or 1 castle nut from 1/4 "to 2", screw-in end 2.5 d

For screwing into soft metal

DIN 941 - Part 1 · Edition 1.1926 → withdrawn

Bare studs · for 2 nuts from M 3 to M 10, screw-in end 1 d

DIN 941 - Part 2 · Edition 1.1926 → withdrawn

Bare studs · for 2 nuts from M 12 to M 30, screw-in end 1 d

DIN 941 - Part 3 · Edition 1.1926 → withdrawn

Bare studs · for 2 nuts from 1/4 "to 2", screw-in end 1 d

DIN 942 - Part 1 · Edition 1.1926 → withdrawn

Bare studs · for 2 nuts from M 3 to M 10, screw-in end 1.3 d

For screwing into gray cast iron

DIN 942 - Part 2 · Edition 1.1926 → withdrawn

Bare studs · for 2 nuts from M 11 to M 52, screw-in end 1.3 d

For screwing into gray cast iron

DIN 942 - Part 3 · Edition 1.1926 → withdrawn

Bare studs · for 2 nuts from 1/4 "to 2", screw-in end 1.3 d

For screwing into gray cast iron

DIN 943 - Part 1 · Edition 1.1948 → withdrawn

Studs · screw-in end ≈ 2.5 d for screwing into soft metal · M3 to M52

DIN 943 - Part 2 · Edition 1.1926 → withdrawn

Bare studs · for 2 nuts from M 11 to M 52, screw-in end 2.5 d

For screwing into gray cast iron

DIN 943 - Part 3 · Edition 1.1926 → withdrawn

Studs for 2 nuts, screw-in end ≈ 2.5 d, for screwing into soft metal 1/4 "to 2"

DIN 944 - Part 1 · Edition 1.1926 → withdrawn

Bare studs with groove · for 1 nut or 1 castle nut from M 5 to M 10, screw-in end 1 d

DIN 944 - Part 2 · Edition 1.1926 → withdrawn

Bare studs with groove · for 1 nut or 1 castle nut from M 11 to M 52, screw-in end 1 d

DIN 944 - Part 3 · Edition 1.1926 → withdrawn

Studs with groove for 1 nut or 1 castle nut with ≈ 0.8 d height, for screwing into steel, cast steel, bronze · screw-in end ≈ 1 d · 1/4 "to 2"

DIN 945 - Part 1 · Edition 1.1926 → withdrawn

Bare studs with groove · for 1 nut or 1 castle nut from M 5 to M 10, screw-in end 1.3 d

DIN 945 - Part 2 · Edition 1.1926 → withdrawn

Bare studs with groove · for 1 nut or 1 castle nut from M 11 to M 52, screw-in end 1.3 d

DIN 945 - Part 3 · Edition 1.1956 → withdrawn

Studs with groove for 1 nut or 1 castle nut with ≈ 0.8 d height, for screwing into gray cast iron · with the same thread on both sides · 1/4 "to 2"

DIN 945 - Part 3 · Edition 1.1926 → withdrawn

Studs with groove · for 1 nut or 1 castle nut, screw-in end ≈ 1.3 d, for screwing into gray cast iron · 1/4 "to 2"

DIN 946 edition 10.1991 → replaced by DIN EN ISO 16047 edition 10.2005

Determination of the coefficients of friction of screws and nuts under specified conditions

DIN 947 - Part 1 · Edition 1.1926 → withdrawn

Bare studs with groove · for 2 nuts from M 5 to M 10, screw-in end 1 d

DIN 947 - Part 2 · Edition 1.1926 → withdrawn

Bare studs with groove · for 2 nuts from M 11 to M 52, screw-in end 1 d

DIN 947 - Part 3 · Edition 1.1926 → withdrawn

Bare studs with groove · for 2 nuts from 1/4 "to 2", screw-in end 1 d

DIN 948 - Part 1 · Edition 1.1926 → withdrawn

Bare studs with groove · for 2 nuts from M 5 to M 10, screw-in end 1.3 d

DIN 948 - Part 2 · Edition 1.1926 → withdrawn

Bare studs with groove · for 2 nuts from M 11 to M 52, screw-in end 1.3 d

DIN 948 - Part 3 · Edition 1.1926 → withdrawn

Studs with groove · for 2 nuts, screw-in end ≈ 1.3 d, for screwing into gray cast iron · 1/4 "to 2"

DIN 949 - Part 1 Edition 2.1995 → 3.2009 withdrawn without replacement

Stud bolts with metric thread MFS screw-in length ≈ 2 d (form A)

DIN 949 - Part 2 Edition 7.1995 → 3.2009 withdrawn without replacement

Studs with metric thread MFS screw-in length ≈ 2.5 d (form B)

DIN 949 - Part 2 · Edition 2.1995 → replaced by Edition 7.1995

Studs with metric thread MFS screw-in length ≈ 2.5 d (form B)

DIN 950 Edition 3.2000 → current

Handwheels offset · Hub hole round or with a straight square

DIN 950 · Edition 6.1970 → replaced by Edition 3.2000

Handwheels, cranked · Hub hole round

DIN 950 edition 9.1962 → withdrawn

Handwheels, cranked · Hub hole round

DIN 950 edition 1.1926 → withdrawn

Handwheels · with full rim and round hole

Unchanged summary of DIN 950 parts 1 and 2 editions 1.1926

DIN 951 edition 4.1972 → replaced by DIN 950 edition 3.2000

Handwheels, offset · Straight square hub hole

DIN 951 - Part 1 · Edition 1.1926x → withdrawn

Handwheels · with full rim and straight square hole

Cross edition 9.1952

DIN 951 - Part 2 · Edition 1.1926x → withdrawn

Handwheels · with full rim and straight square hole · designs

Cross edition 9.1952

DIN 952 - Part 1 · Edition 1.1926 → withdrawn

Handwheels · with full rim and tapered square hole

DIN 952 - Part 2 · Edition 1.1926 → withdrawn

Handwheels · with full rim and tapered square hole · designs

DIN 955 edition 4.1973 → 8.1998 withdrawn without replacement

Handwheels, offset, made of plastic

DIN 955 edition 8.1944 → withdrawn

Smooth handwheels and crank handwheels with a full rim made of pressed material

DIN 956 edition 4.1973 → 8.1998 withdrawn without replacement

Disc handwheels, offset, made of plastic

DIN 956 edition 8.1944 → withdrawn

Disc handwheels made of molded material

DIN 957 edition 7.1944x → withdrawn

Rotatable ball handles · Compressed material

Cross edition 12.1951

DIN 958 Edition 7.1944 → withdrawn

Fixed ball handles · compressed material

DIN 959 edition 1.1969 → 8.1998 withdrawn without replacement

Ball cranks

DIN 960 edition 1.1990 → replaced by DIN EN 28765 edition 2.1992

Hexagon head bolts with shank · Fine thread M8 × 1 to M100 × 4 · Product classes A and B

DIN 960 edition 12.1983 → replaced by edition 1.1990

Hexagon head bolts with shank · Fine thread M8 × 1 to M100 × 4 · Product classes A and B

DIN 960 edition 11.1970 → replaced by edition 12.1983

Hexagon head screws · Metric fine thread, versions m and mg

DIN 960 edition 2.1953 → withdrawn

Hexagon head screws M8 × 1 to M10 × 1, M12 × 1.5 to M24 × 1.5, M18 × 2 to M33 × 2, M36 × 3 to M52 × 3, M56 × 4 to M100 × 4 Version m and mg

DIN 960 edition 4.1942 → withdrawn

Hexagon head bolts M8 × 1 to M100 × 4 Version m and mg

DIN 961 edition 1.1990 → replaced by DIN EN 28676 edition 2.1992

Hexagon head bolts with thread up to the head · Fine thread M8 × 1 to M52 × 3 · Product classes A and B

DIN 961 edition 12.1983 → replaced by edition 1.1990

Hexagon head bolts with thread up to the head · Fine thread M8 × 1 to M52 × 3 · Product classes A and B

DIN 961 edition 11.1970 → replaced by edition 12.1983

Hexagon head screws · thread almost to the head, metric fine thread, versions m and mg

DIN 961 edition 12.1953 → withdrawn

Hexagon head screws, thread almost up to the head M8 × 1 to M10 × 1, M12 × 1.5 to M24 × 1.5, M18 × 2 to M33 × 2, M36 × 3 to M52 × 3 Version m and mg

DIN 961 edition 12.1952 → withdrawn

Hexagon head bolts, thread almost up to the head · Metric fine thread, versions m and mg

DIN 962 · Edition 4.2013 → current

Bolts and nuts · Designation information · Shapes and designs

DIN 962 edition 11.2001 → replaced by edition 4.2013

Bolts and nuts · Designation information · Shapes and designs

DIN 962 edition 9.1990 → replaced by edition 11.2001 and DIN 34803: edition 11.2001

Bolts and nuts · Designation information · Shapes and designs

DIN 962 edition 12.1983 → replaced by edition 9.1990

Bolts and nuts · Designation information · Shapes and designs

DIN 962 edition 9.1975 → replaced by edition 12.1983

Screws and nuts, additional shapes and designs · Order information and dimensions

DIN 962 edition 8.1969 → replaced by edition 9.1975

Screws · Shapes and designs with additional order information

DIN 962 edition 3.1953 → withdrawn

Hexagon head screws · Studs · Shapes and designs with additional order information

DIN 963 edition 8.1990 → replaced by DIN EN ISO 2009 edition 10.1994

Countersunk screws with slot

DIN 963 edition 4.1985 → replaced by edition 8.1990

Countersunk screws with slot, previous countersunk heads according to ISO 2009-1972

DIN 963 · Edition 6.1970 → replaced by Edition 4.1985

Countersunk screws with slot · Countersunk heads according to ISO

DIN 964 edition 8.1990 → replaced by DIN EN ISO 2010 edition 10.1994

Raised countersunk head screws with slot

DIN 964 edition 5.1985 → replaced by edition 8.1990

Raised countersunk head screws with slot, previous countersunk heads according to ISO 2010-1972

DIN 964 · Edition 6.1970 → replaced by Edition 4.1985

Raised countersunk head screws with slotted countersunk heads to ISO

DIN 965 edition 8.1990 → replaced by DIN EN ISO 7046 parts 1 and 2 editions 10.1994

Countersunk screws with cross recess

DIN 965 edition 12.1984 → replaced by edition 8.1990

Countersunk screws with cross recess

DIN 965 edition 12.1971 → replaced by edition 12.1984

Countersunk screws with cross recess · Countersunk heads according to ISO

DIN 966 edition 8.1990 → replaced by DIN EN ISO 7047 edition 10.1994

Pan head countersunk head screws

DIN 966 edition 12.1984 → replaced by edition 8.1990

Pan head countersunk head screws

DIN 966 edition 12.1971 → replaced by edition 12.1984

Raised countersunk head screws with cross recess · Countersunk heads according to ISO

DIN 967 edition 12.2002 → current

Pan head screws with collar and cross recess · Product class A

DIN 967 edition 1.1994 → replaced by edition 12.2002

Pan head screws with collar and cross recess · Product class A

DIN 968 edition 5.2008 → current

Pan head tapping screws with collar and cross recess

The standard specifies the properties of pan head tapping screws with collar and cross recess for thread sizes ST2.9 to ST6.3.

DIN 968 edition 12.2002 → replaced by edition 5.2008

Pan head tapping screws with collar and cross recess

DIN 968 edition 1.1994 → replaced by edition 12.2002

Pan head tapping screws with collar and cross recess

DIN 969 edition 12.1997 → current

Fasteners with thread · Vibration resistance test with axial load · Test method and evaluation of the results

DIN 970 edition 7.1982 → replaced by DIN ISO 4032 edition 10.1987

Hexagon nuts Type 1, metric standard thread, product classes A and B, ISO 4032 modified

DIN 971 - Part 1 edition 10.1987 → replaced by DIN ISO 8673 edition 1.1990

Hexagon nuts Type 1 metric fine thread, strength classes 6 and 8

DIN 971 - Part 1 · Edition 12.1983 → replaced by Edition 10.1987

Hexagon nuts Type 1 Metric fine thread Strength classes 6 and 8

DIN 971 - Part 2 Edition 10.1987 → replaced by DIN ISO 8674 Edition 1.1990

Hexagon nuts type 2 metric fine thread property classes 10 and 12

DIN 971 - Part 2 Edition 12.1983 → replaced by Edition 10.1987

Hexagon nuts type 2 metric fine thread property classes 10 and 12

DIN 972 edition 12.1983 → replaced by DIN ISO 4034 edition 10.1987

Hexagon nuts Type 1 Thread M5 to M39 Product class C, ISO 4034 modified

DIN 974 - Part 1 · Edition 2.2008 → current

Countersink diameter · Construction dimensions · Screws with cylinder head

The standard contains dimensional specifications for countersunk diameters for screws with cylinder heads.

DIN 974 - Part 1 · Edition 5.1991 → replaced by Edition 2.2008

Countersink diameter for screws with cylinder head · Construction dimensions

The standard contains dimensional specifications for countersunk diameters for screws with cylinder heads.

DIN 974 - Part 2 · Edition 5.1991 → current

Countersunk diameter for hexagon screws and hexagon nuts · Construction dimensions

The standard contains dimensional specifications of countersunk diameters for hexagon bolts and nuts.

DIN 974 edition 3.1972 → replaced by DIN 974 parts 1 and 2 edition 5.1991

Countersink diameter · for cylindrical countersinks, overview and application

DIN 975 edition 9.1986 → 7.1995 withdrawn without replacement

Threaded rods

DIN 975 edition 1.1970 → replaced by edition 9.1986

Threaded rods

DIN 976 - Part 1 Edition 9.2016 → current

Threaded bolt · Metric thread

The standard contains the dimensional specifications and technical delivery conditions for threaded bolts and specifies their designation.

DIN 976 - Part 1 Edition 12.2002 → replaced by Edition 9.2016

Threaded bolt · Metric thread

The standard contains the dimensional specifications and technical delivery conditions for threaded bolts and specifies their designation.

DIN 976 - Part 1 · Edition 2.1995 → replaced by Edition 12.2002

Threaded bolt · Metric thread

The standard contains the dimensional specifications and technical delivery conditions for threaded bolts and specifies their designation.

DIN 976 - Part 2 Edition 9.2016 → current

Mechanical fasteners · Threaded bolt · Metric tight fit MFS thread

The standard describes threaded bolts that are used for screwing into components made of light metal, including aluminum.

DIN 976 - Part 2 · Edition 2.2009 → replaced by Edition 9.2016

Threaded bolt · Metric thread MFS

The standard contains the dimensional specifications and technical delivery conditions for threaded bolts with MFS metric threads and specifies their designation.

DIN 976 - Part 2 · Edition 2.1995 → replaced by Edition 2.2009

Threaded bolt · Metric thread MFS

DIN 976 edition 9.1986 → replaced by DIN 976 part 1 edition 2.1995

Threaded bolt

DIN 976 edition 1.1970 → replaced by edition 9.1986

Threaded bolt

DIN 977 edition 2.1998 → replaced by DIN EN ISO 21670 edition 1.2004

Hexagon weld nuts with flange

The standard contains the dimensional specifications and technical delivery conditions for hexagon weld nuts with flange and specifies their designation.

DIN 979 edition 8.2013 → current

Low hexagon castle nuts · Metric standard and fine threads · Product grades A and B

The standard specifies the properties of low hexagon castle nuts with metric standard and fine threads with a nominal thread diameter of 6 mm to 52 mm.

DIN 979 edition 10.2000 → replaced by edition 8.2013

Low castle nuts · Metric standard and fine threads · Product classes A and B

The standard contains the dimensional specifications and technical delivery conditions for low castle nuts, metric standard and fine threads, product classes A and B and specifies their designation.

DIN 979 edition 2.2000 → replaced by edition 10.2000

Low castle nuts · Metric standard and fine threads · Product classes A and B

DIN 979 edition 10.1987 → replaced by edition 2.2000

Low castle nuts · Metric standard and fine threads · Product classes A and B

DIN 979 edition 12.1983 → replaced by edition 10.1987

Castle nuts, low shape

DIN 979 edition 4.1977 → replaced by edition 12.1983

Castle nuts, low shape

DIN 979 edition 12.1972 → withdrawn

Castle nuts, low shape

DIN 980 edition 5.1987 → replaced by DIN EN ISO 10513 edition 3.1998

Hexagon nuts with clamping part, all-metal nuts

DIN 980 edition 12.1972 → replaced by edition 5.1987

Self-locking nuts, clamping

DIN 981 Edition 6.2009 → current

Rolling bearings · locknuts

The use of these locknuts in connection with lock washers according to DIN 5406 mainly relates to adapter sleeves and withdrawal sleeves.

DIN 981 edition 2.1993 → replaced by edition 6.2009

Rolling bearings · locknuts

DIN 981 edition 1.1983 → replaced by edition 2.1993

Rolling bearing accessories · Locknuts

DIN 981 edition 1.1973 → withdrawn

Rolling bearing accessories · Locknuts

DIN 982 edition 5.1987 → replaced by DIN EN ISO 10512 edition 2.1998 and DIN EN ISO 7040 edition 2.1998

Hexagon nuts with clamping part, with non-metallic insert, tall shape

DIN 982 edition 9.1977 → replaced by edition 5.1987 and DIN 6924 edition 11.1983

Hexagon nuts · self-locking, tall shape

DIN 982 edition 12.1967 → replaced by edition 9.1977

Hexagon nuts · self-locking high shape

DIN 983 · Edition 4.2011 → current

Retaining rings with tabs (retaining rings), for shafts

The standard applies to circlips, with several tabs evenly distributed around the circumference, for shafts.

DIN 983 edition 9.1981 → replaced by edition 4.2011

Retaining rings with tabs (retaining rings), for shafts

DIN 983 Edition 3.1965 → withdrawn

Retaining rings with tabs, for shafts

DIN 984 · Edition 4.2013 → current

Retaining rings with tabs (retaining rings) for holes

The standard applies to circlips, with several tabs evenly distributed around the circumference, for bores.

DIN 984 edition 9.1981 → replaced by edition 4.2013

Retaining rings with tabs (retaining rings) for holes

DIN 984 edition 3.1965 → withdrawn

Retaining rings with tabs, for holes

DIN 985 edition 5.1987 → replaced by DIN EN ISO 10511 edition 2.1998

Hexagon nuts with clamping part, with non-metallic insert, low shape

DIN 985 edition 9.1977 → replaced by edition 5.1987

Hexagon nuts · self-locking, low shape

DIN 985 edition 12.1967 → replaced by edition 9.1977

Hexagon nuts · self-locking, low shape

DIN 985 edition 10.1960 → withdrawn

Hexagon nuts, self-locking M3 to M48, M8 × 1 to M10 × 1, M12 × 1.5 to M24 × 1.5, M18 × 2 to M33 × 2 and M36 × 3 to M48 × 3

DIN 985 edition 7.1951 → withdrawn

Hexagon nuts, self-locking

DIN 986 edition 8.2013 → current

Hexagon cap nuts with clamping part, with non-metallic insert

The standard contains the dimensional specifications and technical delivery conditions for hexagon cap nuts with clamping part with non-metallic insert and specifies their designation.

DIN 986 edition 10.2000 → replaced by edition 8.2013

Hexagon cap nuts with clamping part, with non-metallic insert

DIN 986 edition 2.2000 → replaced by edition 10.2000

Hexagon cap nuts with clamping part, with non-metallic insert

DIN 986 edition 6.1987 → replaced by edition 2.2000

Hexagon cap nuts with clamping part, with non-metallic insert

DIN 986 edition 9.1977 → replaced by edition 6.1987

Hexagon cap nuts, self-locking

DIN 986 edition 11.1963 → withdrawn

Cap nuts, self-locking

DIN 986 edition 10.1960 → withdrawn

Cap nuts, self-locking M4 to M20, M8 × 1 to M10 × 1, M12 × 1.5 to M20 × 1.5 and M 20 × 2

DIN 986 edition 7.1951 → withdrawn

Cap nuts, self-locking

DIN 987 edition 10.1960 → 7.2012 withdrawn without replacement

Rivet nuts · with steel core, self-locking

DIN 987 edition 7.1951 → withdrawn

Rivet nuts · with steel core, self-locking

DIN 988 Edition 3.1990 → current

Shim washers and support washers

The standard contains the dimensional specifications and technical delivery conditions for shims and support disks and specifies their designation.

DIN 988 edition 5.1971 → replaced by edition 3.1990

Shim washers and support washers

DIN 988 edition 8.1950 → withdrawn

Shims

DIN 989 - Part 1 Edition 11.1932 → withdrawn

Railings made of pipe · Railing pillars, handrails, bars

DIN 989 - Part 2 Edition 11.1932 → withdrawn

Railing made of pipe · Railing fittings, railing tubes

DIN 989 - Part 3 Edition 11.1932 → withdrawn

Railings made of pipe · Application examples

DIN 990 - Part 1 Edition 11.1932 → withdrawn

Railings made of solid bars · Pillar base, pillar holder

DIN 990 - Part 2 Edition 11.1932 → withdrawn

Railings made of solid bars · Railing columns, handrail bars, application examples

DIN 991 edition 2.1933 → 1.1970 withdrawn without replacement

Symbols for transmission parts

DIN 992 Edition 7.1944 → withdrawn

Chains, tempered, tested · Guidelines for the requirements for tempered round link chains

DIN 993 Edition 6.1943 → withdrawn

Can conveyor chains

DIN 994 edition 7.1930 → withdrawn

Standard wooden pulleys (spoke disks) · Terms of delivery

DIN 995 edition 1.1970 → replaced by DIN 471 , DIN 472 , DIN 983 and DIN 984

Retaining rings · Application and installation

DIN 996 edition 4.1927 → withdrawn

Marking gauges for bar and shaped iron

DIN 997 edition 10.1970 → withdrawn

Marking dimensions (root dimensions) for structural steel and bar steel

DIN 997 edition 3.1956 → withdrawn

Root dimensions (marking dimensions) for bars and sections

DIN 997 edition 4.1927 → withdrawn

Root dimensions for rod and shaped iron

DIN 998 edition 10.1970 → withdrawn

Hole spacing in unequal angle steels

DIN 998 edition 1.1958 → withdrawn

Rivet spacing for unequal angle steels

DIN 998 - Part 1 · Edition 4.1927 → withdrawn

Rivet spacing for unequal angle irons

DIN 998 - Part 2 · Edition 4.1927 → withdrawn

Rivet spacing for unequal angle irons

DIN 998 - Part 3 · Edition 4.1927 → withdrawn

Rivet spacing for unequal angle irons

DIN 999 edition 10.1970 → withdrawn

Hole spacing in isosceles angle steels

DIN 999 edition 3.1956 → withdrawn

Rivet spacing for isosceles angle steels

DIN 999 - Part 1 Edition 7.1927 → withdrawn

Rivet spacing for isosceles angle irons

DIN 999 - Part 2 Edition 7.1927 → withdrawn

Rivet spacing for isosceles angle irons

See also

• List of DIN standards

swell

• DIN standard sheet directory 1931 (Beuth-Verlag, Berlin)
• DIN standard sheet directory 1935 (Beuth-Verlag GmbH, Berlin)
• DIN standard sheet directory 1942 (Beuth-Vertrieb GmbH, Berlin)
• DIN standard sheet directory 1950 (Beuth-Vertrieb GmbH, Berlin)
• DIN standard sheet directory 1953 (Beuth-Vertrieb GmbH, Berlin)
• DIN standard sheet directory 1956 (Beuth-Vertrieb GmbH, Berlin)
• DIN standard sheet directory 1963 (Beuth-Vertrieb GmbH, Berlin)
• DIN standard sheet directory 1974 (Beuth-Vertrieb GmbH, Berlin)
• DIN standards committees (all valid, as well as new and withdrawn standards of the respective standards committee)
• Beuth Verlag - Product search
• Beuth Verlag - Search for historical documents (registration required)