List of standards DIN 1 to DIN 499
The list of standards DIN 1 to DIN 499 lists all current standards and many historical standard editions in the number range 1 to 499.
DIN - German Institute for Standardization e. V. - is the national standardization organization of the Federal Republic of Germany based in Berlin .
Explanations of the list
- DIN-EN standards, DIN-EN-ISO standards, DIN-ISO standards, preliminary standards and draft standards are not listed in this list.
- The term “sheet” used in older standard editions has been uniformly transferred to “part”.
- The date of issue is indicated next to the standard number. Edition 9.1981 means that the standard was published in September 1981.
- Cross edition: If the date of issue is appended with an x, for example edition 9.1949x, the standard has only been changed slightly and remains valid.
- Unless otherwise noted, the withdrawal date of an old standard is the same as the issue date of the replacing standard (s).
- The entry "→ current" means that the standard is currently (as of June 2017) valid.
DIN 1 edition 9.1981 → replaced by DIN EN 22339 edition 10.1992 (in accordance with ISO 2339 edition 11.1986)
Conical pins , unhardened
DIN 1 edition 3.1961 → replaced by edition 9.1981
Taper pins
DIN 1 edition 6.1956 → replaced by edition 3.1961
Taper pins
DIN 1 edition 1.1943 → replaced by edition 6.1956
Taper pins
DIN 1 edition 1.1941 → replaced by edition 1.1943
Taper pins
DIN 1 edition 7.1936 → replaced by edition 1.1941
Taper pins
DIN 1 edition 2.1932 → replaced by edition 7.1936
Taper pins
DIN 1 edition 2.1925 → replaced by edition 2.1932
Taper pins
DIN 1 edition 3.1918 → replaced by edition 2.1925
Taper pins
DIN 2 edition 3.1918 → withdrawn
Weights of the tapered pins according to DIN standard 1
DIN 3 edition 2.1955 → replaced by DIN 323 part 1 edition 8.1974
Standard dimensions
DIN 3 - Part 1 · Edition 4.1952 → replaced by DIN 3 Edition 2.1955
Standard dimensions millimeters
DIN 3 edition 12.1939 → replaced by DIN 3 part 1 edition 4.1952
Standard diameters and other structural dimensions (nominal dimensions) for machines, apparatus and metal goods
DIN 3 edition 10.1939 → replaced by edition 12.1939
Standard diameters and other structural dimensions (nominal dimensions) for machines, apparatus and metal goods
DIN 3 edition 1.1923 → replaced by edition 10.1939
Normal diameter
DIN 3 edition 10.1922 → replaced by edition 1.1923
Standard diameter
DIN 4 edition 7.1919 → withdrawn
Standard sheet · Dimensions
DIN 5 - part 10 edition 12.1986 → replaced by DIN ISO 10209 part 2 edition 12.1994
Technical drawings · projections, terms
DIN 5 - part 1 edition 12.1970 → replaced by DIN ISO 5456 part 3 edition 4.1998
Drawings · Axonometric Projections · Isometric Projection
DIN 5 - Part 2 Edition 12.1970 → replaced by DIN ISO 5456 Part 3 Edition 4.1998
Drawings · Axonometric Projections · Dimetric Projection
DIN 5 edition 10.1948 → replaced by DIN 5 parts 1 and 2 editions 12.1970
Drawings · Axonometric projections
The edition of the standard is a complete revision of edition 4.1929.
DIN 5 edition 4.1929 → replaced by edition 10.1948
Drawings · Perspective representations · Inclined parallel projection, axonometric projections
DIN 5 edition 12.1919 → replaced by edition 4.1929
Drawings · Sheet sizes, scales · Color of the representation
DIN 6 - Part 1 · Edition 12.1986 → replaced by DIN ISO 5456 Part 2 Edition 4.1998 and DIN ISO 128 Part 30 and 34 Edition 5.2002
Representations in normal projection · Views and special representations
DIN 6 - Part 2 edition 12.1986 → replaced by DIN ISO 128 parts 40, 44 and 50 edition 5.2002
Representations in normal projection · Sections
DIN 6 edition 3.1968 → replaced by DIN 6 parts 1 and 2 editions 12.1986, DIN 5 part 10 edition 12.1986 and DIN ISO 6433 edition 9.1982
Representations in drawings · Views, sections, special representations
DIN 6 edition 10.1956 → replaced by edition 3.1968
Views, sections, special representations
DIN 6 - edition 11.1950x → replaced by edition 10.1956
Drawings · Arrangement of views and sections
Figure 7 has been changed and the penultimate paragraph added.
DIN 6 - edition 11.1922x → replaced by edition 10.1956
Drawings · Arrangement of views and sections
DIN 7 edition 9.1981 → 10.1992 replaced by DIN EN 22338 edition 10.1992
Straight pins
DIN 7 · Edition 6.1956 → replaced by Edition 9.1981
Straight pins
DIN 7 edition 1.1943 → replaced by edition 6.1956
Straight pins
DIN 7 edition 7.1936 → replaced by edition 1.1943
Straight pins
DIN 7 edition 4.1927 → withdrawn
Straight pins
DIN 7 - Supplement 2 · Edition 4.1927 → withdrawn
Parallel pins Version 2
Finishing shaft fit
DIN 7 edition 2.1925 → withdrawn
Straight pins
DIN 7 edition 2.1919 → withdrawn
Straight pins
DIN 8 edition 2.1919 → withdrawn
Weights of the parallel pins according to DIN 7
DIN 9 edition 12.1996 → current
Hand taper reamers for taper pin bores
Hand reamers according to this standard are intended for reaming bores with a taper 1:50.
DIN 9 edition 6.1975 → replaced by edition 12.1996
Hand taper reamers for taper pin bores
DIN 9 edition 3.1957 → replaced by edition 6.1975
Taper reamers with taper 1:50 for taper pins according to DIN 1 and DIN 7978
DIN 9 edition 3.1943 → replaced by edition 3.1957
Taper reamers for taper pins according to DIN 1
DIN 9 edition 10.1921 → replaced by edition 3.1943
Taper reamers for taper pins according to DIN 1
DIN 10 edition 12.2009 → current
Square edge of cylindrical shanks for rotating tools
The standard applies to the square of cylindrical shanks on machine-operated tools and hand-operated threading tools.
DIN 10 edition 6.1997 → replaced by edition 12.2009
Square edge of cylindrical shanks for rotating tools
DIN 10 edition 2.1994 → replaced by edition 6.1997
Square edge of cylindrical shanks for rotating tools
DIN 10 - Part 1 · Edition 4.1973 → replaced by Edition 2.1994
Tool square and shank diameter according to ISO for rotating tools · Dimensions
DIN 10 edition 10.1970 → replaced by edition 2.1994
Tool square
DIN 10 edition 4.1948 → replaced by edition 10.1970
Tool square · Dimensions, limit dimensions , gauge dimensions
DIN 10 - Part 2 · Edition 6.1947 → replaced by DIN 10 Edition 4.1948
Tool square · gauge size
DIN 10 - Part 1 edition 9.1943 → replaced by DIN 10 edition 4.1948
Tool square · Dimensions and limit dimensions
DIN 10 edition 12.1919 → withdrawn
Square edge for tools and for movement spindles on machine tools
DIN 11 edition 7.1958 → withdrawn
Whitworth thread from 1/4 "to 6" nominal thread diameter · Nominal dimensions, gauge information
DIN 11 - Supplement 1 · Edition 6.1930 → withdrawn
Whitworth thread · Dimensions and tolerances - fine
DIN 11 - Supplement 2 · Edition 6.1930 → withdrawn
Whitworth thread · Thread limit dimensions - fine
DIN 11 - Supplement 3 · Edition 6.1930 → withdrawn
Whitworth thread · Dimensions and tolerances - medium and large
DIN 11 - Supplement 4 Edition 6.1930 → withdrawn
Whitworth thread · Thread limit dimensions medium and coarse
DIN 11 - Supplement 5 · Edition 6.1930 → withdrawn
Whitworth thread · Manufacturing accuracy and thread gauge wear
DIN 11 - Supplement 6 · Edition 6.1930 → withdrawn
Whitworth thread · Good thread plug gauge · Limits fine, medium, coarse
DIN 11 - Supplement 7 · Edition 6.1930 → withdrawn
Whitworth thread · Rejected thread plug gauge · Limits fine, medium, coarse
DIN 11 - Supplement 8 · Edition 6.1930 → withdrawn
Whitworth thread · Adjustment thread gauge for the wear tester for good thread plug gauge · Limits fine, medium, coarse
DIN 11 - Supplement 9 · Edition 6.1930 → withdrawn
Whitworth thread · Good thread ring gauge · Limits fine, medium, coarse
DIN 11 - Supplement 11 · Edition 6.1930 → withdrawn
Whitworth thread · fitting mandrel and wear test mandrel for good thread ring gauge · limit dimensions fine, medium, coarse
DIN 11 - Supplement 12 · Edition 6.1930 → withdrawn
Whitworth thread · Adjustment thread gauge, good and reject · Limits fine, medium, coarse
DIN 11 edition 6.1923x → replaced by edition 7.1958
Whitworth thread without tip clearance
DIN 11 edition 4.1922 → replaced by edition 6.1923x
Whitworth thread without tip clearance
DIN 12 edition 6.1923 → withdrawn
Whitworth thread with point clearance
DIN 12 edition 6.1922 → replaced by edition 6.1923
Whitworth thread with point clearance
DIN 12 edition 8.1921 → withdrawn
Whitworth thread with point clearance
DIN 12 edition 2.1919 → replaced by edition 8.1921
Whitworth thread with point clearance
DIN 13 - Part 1 · Edition 11.1999 → current
Metric ISO threads for general use · Nominal dimensions for standard threads; Nominal thread diameter from 1 mm to 68 mm
The standard defines nominal dimensions.
DIN 13 - Part 1 · Edition 12.1986 → replaced by Edition 11.1999
Metric ISO thread · standard thread from 1 to 68 mm nominal thread diameter · nominal dimensions
DIN 13 - Part 1 · Edition 3.1973 → replaced by Edition 12.1986
Metric ISO thread · standard thread from 1 to 68 mm thread diameter · nominal dimensions
DIN 13 - Part 1 · Edition 2.1949x → withdrawn
Metric thread from 0.3 to 68 mm nominal thread diameter, theoretical values
DIN 13 - Part 1 · Edition 2.1949 → withdrawn
Metric thread from 0.3 to 68 mm nominal thread diameter · theoretical values
DIN 13 - Part 2 · Edition 11.1999 → current
Metric ISO threads for general use · Nominal dimensions for fine threads with pitches 0.2 mm, 0.25 mm and 0.35 mm · Nominal thread diameters from 1 mm to 50 mm
The standard defines nominal dimensions.
DIN 13 - Part 2 · Edition 12.1986 → replaced by Edition 11.1999
Metric ISO thread · Fine thread with pitches of 0.2 mm, 0.25 mm and 0.35 mm from 1 to 50 mm nominal thread diameter · Nominal dimensions
DIN 13 - Part 2 · Edition 3.1970 → replaced by Edition 12.1986
Metric ISO thread · Fine thread with pitches 0.2 - 0.25 - 0.35 mm from 1 to 50 mm thread diameter · Nominal dimensions
DIN 13 - Part 2 · Edition 1.1945 → withdrawn
Tolerances and gauge dimensions for metric threads with tolerances f (fine), m (medium), g (coarse)
DIN 13 - Part 3 · Edition 11.1999 → current
Metric ISO thread for general use · Nominal dimensions for fine threads with a pitch of 0.5 mm · Nominal thread diameter from 3.5 mm to 90 mm
The standard defines nominal dimensions.
DIN 13 - Part 3 · Edition 12.1986 → replaced by Edition 11.1999
Metric ISO thread · Fine thread with pitch 0.5 mm from 3.5 to 90 mm nominal thread diameter · Nominal dimensions
DIN 13 - Part 3 · Edition 3.1970 → replaced by Edition 12.1986
Metric ISO thread · Fine thread with pitch 0.5 mm from 3.5 to 90 mm thread diameter · Nominal dimensions
DIN 13 - Part 4 Edition 11.1999 → current
Metric ISO thread for general use · Nominal dimensions for fine threads with a pitch of 0.75 mm · Nominal thread diameter from 5 mm to 110 mm
The standard defines nominal dimensions.
DIN 13 - part 4 edition 12.1986 → replaced by edition 11.1999
Metric ISO thread · fine thread with pitch 0.75 mm from 5 to 110 mm nominal thread diameter · nominal dimensions
DIN 13 - Part 4 · Edition 4.1970 → replaced by Edition 12.1986
Metric ISO thread · fine thread with pitch 0.75 mm from 5 to 110 mm thread diameter · nominal dimensions
DIN 13 - Part 5 · Edition 11.1999 → current
Metric ISO threads for general use · Nominal dimensions for fine threads with pitches 1 mm and 1.25 mm · Nominal thread diameters from 7.5 mm to 200 mm
The standard defines nominal dimensions.
DIN 13 - Part 5 · Edition 12.1986 → replaced by Edition 11.1999
Metric ISO thread · Fine thread with pitches 1 mm and 1.25 mm from 7.5 to 200 mm nominal thread diameter · Nominal dimensions
DIN 13 - Part 5 · Edition 4.1970 → replaced by Edition 12.1986
Metric ISO thread · Fine thread with pitch 1 mm and 1.25 mm from 7.5 to 200 mm thread diameter · Nominal dimensions
DIN 13 - Part 6 Edition 11.1999 → current
Metric ISO thread for general use · Nominal dimensions for fine threads with pitch 1.5 mm · Nominal thread diameter from 12 mm to 300 mm
The standard defines nominal dimensions.
DIN 13 - Part 6 · Edition 12.1986 → replaced by Edition 11.1999
Metric ISO thread · Fine thread with pitch 1.5 mm from 12 to 300 mm nominal thread diameter · Nominal dimensions
DIN 13 - Part 6 Edition 9.1970 → replaced by Edition 12.1986
Metric ISO thread · Fine thread with pitch 1.5 mm from 12 to 300 mm thread diameter · Nominal dimensions
DIN 13 - Part 7 · Edition 11.1999 → current
Metric ISO thread for general use · Nominal dimensions for fine threads with a pitch of 2 mm · Nominal thread diameter from 17 mm to 300 mm
The standard defines nominal dimensions.
DIN 13 - Part 7 12.1986 → replaced by 11.1999 edition
Metric ISO thread · Fine thread with 2 mm pitch from 17 to 300 mm nominal thread diameter · Nominal dimensions
DIN 13 - Part 7 Edition 9.1970 → replaced by Edition 12.1986
Metric ISO thread · Fine thread with pitch 2 mm from 17 to 300 mm thread diameter · Nominal dimensions
DIN 13 - Part 8 · Edition 11.1999 → current
Metric ISO thread for general use · Nominal dimensions for fine threads with a pitch of 3 mm · Nominal thread diameter from 28 mm to 300 mm
The standard defines nominal dimensions.
DIN 13 - Part 8 · Edition 12.1986 → replaced by Edition 11.1999
Metric ISO thread · fine thread with 3 mm pitch from 28 to 300 mm nominal thread diameter · nominal dimensions
DIN 13 - Part 8 · Edition 9.1970 → replaced by Edition 12.1986
Metric ISO thread · fine thread with 3 mm pitch from 28 to 300 mm thread diameter · nominal dimensions
DIN 13 - Part 9 · Edition 11.1999 → current
Metric ISO thread for general use · Nominal dimensions for fine threads with a pitch of 4 mm · Nominal thread diameter from 40 mm to 300 mm
The standard defines nominal dimensions.
DIN 13 - Part 9 · Edition 12.1986 → replaced by Edition 11.1999
Metric ISO thread · Fine thread with a pitch of 4 mm from 40 to 300 mm nominal thread diameter · Nominal dimensions
DIN 13 - Part 9 · Edition 9.1970 → replaced by Edition 12.1986
Metric ISO thread · Fine thread with a pitch of 4 mm from 40 to 300 mm thread diameter · Nominal dimensions
DIN 13 - Part 10 · Edition 11.1999 → current
Metric ISO threads for general use · Nominal dimensions for fine threads with a pitch of 6 mm · Nominal thread diameters from 70 mm to 500 mm
The standard defines nominal dimensions.
DIN 13 - Part 10 · Edition 12.1986 → replaced by Edition 11.1999
Metric ISO thread · Fine thread with a pitch of 6 mm from 70 to 500 mm nominal thread diameter · Nominal dimensions
DIN 13 - Part 10 · Edition 9.1970 → replaced by Edition 12.1986
Metric ISO thread · Fine thread with a pitch of 6 mm from 70 to 500 mm thread diameter · Nominal dimensions
DIN 13 - Part 11 · Edition 11.1999 → current
Metric ISO thread for general use · Nominal dimensions for fine threads with a pitch of 8 mm · Nominal thread diameter from 130 mm to 1000 mm
The standard defines nominal dimensions.
DIN 13 - Part 11 · Edition 12.1986 → replaced by Edition 11.1999
Metric ISO thread · Fine thread with an 8 mm pitch from 130 to 1000 mm nominal thread diameter · Nominal dimensions
DIN 13 - Part 11 edition 11.1970 → replaced by edition 12.1986
Metric ISO thread · Fine thread with a pitch of 8 mm from 130 to 1000 mm thread diameter · Nominal dimensions
DIN 13 - Part 12 Edition 10.1988 → replaced by DIN ISO 261 Edition 11.1999
Metric ISO thread · Regular and fine threads from 1 to 300 mm diameter · Selection for diameter and pitch
The standard defines nominal dimensions.
DIN 13 - part 12 edition 11.1975 → replaced by edition 10.1988
Metric ISO thread · Regular and fine threads from 1 to 300 mm in diameter · Selection for diameters and pitches
DIN 13 - Part 12 Edition 9.1969 → withdrawn
Metric ISO thread · Regular and fine threads from 1 to 300 mm in diameter · Selection for diameters and pitches
DIN 13 - Part 12 Supplement · Edition 11.1975 → replaced by DIN ISO 261 Edition 11.1999
Metric ISO thread · Regular and fine threads from 1 to 300 mm diameter · Overview of threads according to ISO 261-1973
DIN 13 - Part 12 Supplement · Edition 11.1968 → withdrawn
Metric ISO thread · Regular and fine threads from 1 to 300 mm in diameter · Overview
DIN 13 - Part 12 · Edition 1.1952 → withdrawn
Metric profile thread · Selection series
DIN 13 - part 13 edition 10.1983 → replaced by DIN ISO 262 and DIN ISO 965 part 2 edition 11.1999
Metric ISO thread · Selection series for screws, bolts and nuts from 1 to 52 mm thread diameter and limit dimensions
The standard defines nominal dimensions.
DIN 13 - Part 13 · Edition 7.1972 → replaced by Edition 10.1983
Metric ISO thread · Thread overview for screws and nuts from 1 to 52 mm thread diameter and limit dimensions
DIN 13 - part 14 edition 8.1982 → replaced by DIN ISO 965 part 1 edition 11.1999
Metric ISO thread · Basis of the tolerance system for threads from 1 mm in diameter
The standard defines nominal dimensions.
DIN 13 - Part 14 · Edition 3.1972 → withdrawn
Metric ISO thread · Basics of the tolerance system for threads from 1 mm in diameter
DIN 13 - Part 14 · Edition 1.1952 → withdrawn
Thread with metric profile · Basic tolerances for pitch diameters (S series) · Tolerances for bolt thread core diameters, thread engagement length ranges, gauge lengths
DIN 13 - part 15 edition 8.1982 → replaced by DIN ISO 965 part 1 edition 11.1999
Metric ISO thread · Basic dimensions and tolerances for threads from 1 mm in diameter
The standard defines nominal dimensions.
DIN 13 - Part 15 · Edition 3.1972 → withdrawn
Metric ISO thread · Basic dimensions and tolerances for threads from 1 mm in diameter
DIN 13 - Part 15 · Edition 1.1952 → withdrawn
Thread with metric profile · Recommended tolerances for pitch diameter, tolerances for bolt thread outer diameter, tolerances for nut thread core diameter
DIN 13 - Part 16 · Edition 1.1987 → replaced by DIN ISO 1502 Edition 12.1996
Metric ISO thread · Gauges for bolt and nut threads · Gauge system and terms
The standard defines nominal dimensions.
DIN 13 - Part 16 · Edition 6.1976 → replaced by Edition 1.1987
Metric ISO thread · Gauges for bolt and nut threads · Gauge system and terms
DIN 13 - Part 16 · Edition 1.1952 → withdrawn
Thread with metric profile · Gauge dimensions, gauge of the bolt thread
DIN 13 - Part 17 · Edition 1.1987 → replaced by DIN ISO 1502 Edition 12.1996
Metric ISO thread · Gauges for bolt and nut threads · Gauge dimensions and construction features
The standard defines nominal dimensions.
DIN 13 - Part 17 · Edition 6.1976 → replaced by Edition 1.1987
Metric ISO thread · Gauges for bolt and nut threads · Gauge dimensions and construction features
DIN 13 - Part 17 · Edition 1.1952 → withdrawn
Thread with metric profile · Gauge dimensions, gauge of the nut thread
DIN 13 - Part 18 · Edition 1.1987 → replaced by DIN ISO 1502 Edition 12.1996
Metric ISO thread · Gauges for bolt and nut threads · Gauging of workpieces and handling of gauges
DIN 13 - Part 18 · Edition 6.1976 → replaced by Edition 1.1987
Metric ISO thread · Gauges for bolt and nut threads · Gauging of workpieces and handling of gauges
DIN 13 - Part 19 · Edition 11.1999 → current
General purpose ISO metric threads · Nominal profiles
The standard defines nominal dimensions.
DIN 13 - Part 19 · Edition 12.1986 → replaced by Edition 11.1999 and DIN ISO 68 Part 1 Edition 11.1999
Metric ISO thread · Basic profile and production profiles
DIN 13 - Part 19 · Edition 5.1972 → replaced by Edition 12.1986
Metric ISO thread · Basic profile and production profiles
DIN 13 - Part 20 · Edition 8.2000 → current
Metric ISO threads for general use · Limit dimensions for standard threads with preferred tolerance classes · Nominal thread diameters from 1 mm to 68 mm
The standard applies to metric ISO threads with a basic profile according to DIN ISO 68 Part 1.
DIN 13 - Part 20 · Edition 11.1999 → replaced by Edition 8.2000
Metric ISO threads for general use · Limit dimensions for standard threads with preferred tolerance classes · Nominal thread diameters from 1 mm to 68 mm
DIN 13 - Part 20 · Edition 10.1983 → replaced by Edition 11.1999
Metric ISO thread · Limit sizes for standard threads from 1 to 68 mm nominal diameter with common tolerance fields
DIN 13 - Part 20 · Edition 11.1972 → replaced by Edition 10.1983
Metric ISO thread · Limit sizes for standard threads from 1 to 68 mm nominal diameter with common tolerance fields
DIN 13 - Part 21 · Edition 8.2005 → current
Metric ISO threads for general use · Limit dimensions for fine threads with preferred tolerance classes · Nominal thread diameter from 1 mm to 24.5 mm
This standard applies to metric ISO threads of general use with a base profile according to DIN ISO 68 Part 1. It contains limit dimensions for fine threads from 1 mm to 24.5 mm nominal thread diameter with preferred tolerance classes.
DIN 13 - Part 21 · Edition 10.1983 → replaced by Edition 8.2005
Metric ISO thread · Limit sizes for fine threads from 1 to 24.5 mm nominal diameter with common tolerance fields
DIN 13 - Part 21 · Edition 2.1973 → replaced by Edition 10.1983
Metric ISO thread · Limit sizes for fine threads from 1 to 24.5 mm nominal diameter with common tolerance fields
DIN 13 - Part 22 · Edition 8.2005 → current
Metric ISO threads for general use · Limit dimensions for fine threads with preferred tolerance classes · Nominal thread diameter from 25 mm to 52 mm
This standard applies to metric ISO threads of general use with a base profile according to DIN ISO 68 Part 1. It contains limit dimensions for fine threads from 25 mm to 52 mm nominal thread diameter with preferred tolerance classes.
DIN 13 - Part 22 · Edition 10.1983 → replaced by Edition 8.2005
Metric ISO thread · Limit sizes for fine threads from 25 to 52 mm nominal diameter with common tolerance fields
DIN 13 - Part 22 · Edition 2.1973 → replaced by Edition 10.1983
Metric ISO thread · Limit sizes for fine threads from 25 to 52 mm nominal diameter with common tolerance fields
DIN 13 - Part 23 · Edition 8.2005 → current
Metric ISO threads for general use · Limit dimensions for fine threads with preferred tolerance classes · Nominal thread diameters from 53 mm to 110 mm
This standard applies to metric ISO threads of general use with a basic profile according to DIN ISO 68 Part 1. It contains limit dimensions for fine threads from 53 mm to 110 mm nominal thread diameter with preferred tolerance classes
DIN 13 - Part 23 edition 10.1983 → replaced by edition 8.2005
Metric ISO thread · Limit sizes for fine threads from 53 to 110 mm nominal diameter with common tolerance fields
DIN 13 - Part 23 · Edition 2.1973 → replaced by Edition 10.1983
Metric ISO thread · Limit sizes for fine threads from 53 to 110 mm nominal diameter with common tolerance fields
DIN 13 - Part 24 · Edition 8.2005 → current
Metric ISO threads for general use · Limit dimensions for fine threads with preferred tolerance classes · Nominal thread diameter from 112 mm to 180 mm
This standard applies to metric ISO threads of general use with a basic profile according to DIN ISO 68 Part 1. It contains limit dimensions for fine threads from 112 mm to 180 mm nominal thread diameter with preferred tolerance classes.
DIN 13 - Part 24 · Edition 10.1983 → replaced by Edition 8.2005
Metric ISO thread · Limiting dimensions for fine threads from 112 to 180 mm nominal diameter with common tolerance fields
DIN 13 - Part 24 · Edition 2.1973 → replaced by Edition 10.1983
Metric ISO thread · Limiting dimensions for fine threads from 112 to 180 mm nominal diameter with common tolerance fields
DIN 13 - Part 25 · Edition 8.2005 → current
Metric ISO threads for general use · Limit dimensions for fine threads with preferred tolerance classes · Nominal thread diameters from 182 mm to 250 mm
This standard applies to metric ISO threads of general use with a basic profile according to DIN ISO 68 Part 1. It contains limit dimensions for fine threads from 182 mm to 250 mm nominal thread diameter with preferred tolerance classes.
DIN 13 - Part 25 · Edition 10.1983 → replaced by Edition 8.2005
Metric ISO thread · Limit sizes for fine threads from 182 to 250 mm nominal diameter with common tolerance fields
DIN 13 - Part 25 · Edition 2.1973 → replaced by Edition 10.1983
Metric ISO thread · Limit sizes for fine threads from 182 to 250 mm nominal diameter with common tolerance fields
DIN 13 - Part 26 · Edition 8.2005 → current
Metric ISO thread for general use · Limit dimensions for fine threads with preferred tolerance classes · Nominal thread diameter from 252 mm to 1000 mm
The standard applies to metric ISO threads of general use with a base profile according to DIN ISO 68 Part 1. It contains limit dimensions for fine threads from 252 mm to 1000 mm nominal thread diameter with preferred tolerance classes.
DIN 13 - Part 26 · Edition 10.1983 → replaced by Edition 8.2005
Metric ISO thread · Limit dimensions for fine threads from 252 to 1000 mm nominal diameter with common tolerance fields
DIN 13 - Part 26 · Edition 2.1973 → replaced by Edition 10.1983
Metric ISO thread · Limit dimensions for fine threads from 252 to 1000 mm nominal diameter with common tolerance fields
DIN 13 - Part 27 Edition 12.1983 → replaced by DIN ISO 965 Part 3 Edition 11.1999
Metric ISO thread · Regular and fine threads from 1 to 355 mm thread diameter · Dimensions
The standard defines nominal dimensions.
DIN 13 - Part 27 · Edition 8.1973 → replaced by Edition 12.1983
Metric ISO thread · Regular and fine threads from 1 to 355 mm thread diameter · Dimensions
DIN 13 - Part 28 Edition 9.1975 → current
Metric ISO thread · Regular and fine threads from 1 to 250 mm thread diameter · Core cross-sections, tension cross-sections and helix angles
DIN 13 - Part 28 · Edition 8.1973 → withdrawn
Metric ISO thread · Regular and fine threads from 1 to 250 mm thread diameter · Core cross-sections, tension cross-sections and helix angles
DIN 13 - Part 30 · Edition 6.1964 → replaced by DIN 13 Part 19 Edition 12.1986
DIN 13 - Part 31 Edition 6.1964 → replaced by DIN ISO 261
DIN 13 - Part 32 · Edition 6.1964 → replaced by DIN ISO 965-1 and DIN ISO 965-2
DIN 13 - Part 33 · Edition ?? → replaced by DIN ISO 262 and DIN ISO 965-2
DIN 13 - Part 34 · Edition 6.1964 → replaced by DIN 13-1 Edition 11.1999
DIN 13 - Part 35 · Edition ?? → replaced by DIN 13-3 and DIN 13-4
DIN 13 - Part 36 · Edition ?? → replaced by DIN 13-5
DIN 13 - Part 37 · Edition ?? → replaced by DIN 13-6
DIN 13 - Part 38 · Edition ?? → replaced by DIN 13-7
DIN 13 - Part 39 · Edition ?? → replaced by DIN 13-8
DIN 13 - Part 40 · Edition ?? → replaced by DIN 13-9
DIN 13 - Part 41 · Edition ?? → replaced by DIN 13-10
DIN 13 - Part 42 · Edition 6.1964 → withdrawn without replacement
DIN 13 - Part 43 · Edition ?? → replaced by DIN 13-20, DIN 13-21, DIN 13-22, DIN 13-23 and DIN 13-25
DIN 13 - Part 44 · Edition ?? → replaced by DIN 13-1, DIN 13-2 and DIN 13-20
DIN 13 - Part 50 · Edition 5.2017 → current
General purpose metric ISO threads · Combination of tolerance classes for formed internal threads
The standard specifies combinations of tolerance classes for metric ISO internal threads. For threads not dealt with in the standard, DIN ISO 965 Part 1 is to be used.
DIN 13 - Part 50 Edition 11.1999 → replaced by Edition 5.2017
General purpose metric ISO threads · Combination of tolerance classes for grooved internal threads
The standard defines tolerances.
DIN 13 - Part 50 · Edition 11.1986 → replaced by Edition 11.1999
Metric ISO thread · Combination of tolerance zones for the preferred application for grooved internal threads
DIN 13 - Part 51 · Edition 10.2013 → current
Metric ISO thread for general use · External thread with transition tolerance field (previously thread for interference fit) · Tolerances, limit dimensions, limit dimensions
The standard defines tolerance classes for external threads.
DIN 13 - Part 51 · Edition 8.2005 → replaced by Edition 10.2013
Metric ISO thread for general use · External thread with transition tolerance field (previously thread for interference fit) · Tolerances, limit dimensions, limit dimensions
The standard defines tolerance classes for external threads.
DIN 13 - Part 51 · Edition 12.1988 → replaced by Edition 8.2005
Metric ISO thread · Bolt thread with transition tolerance field (previously thread for interference fit) · Tolerances, limit dimensions, limit dimensions
The standard defines tolerance fields for bolt threads.
DIN 13 - Part 52 · Edition 5.2017 → current
General purpose metric ISO thread · Tolerances and profile deviation for multi-start threads
The standard contains specifications for tolerances and profile deviations for multi-start threads. It is a residual standard to DIN ISO 965 Part 1.
DIN 13 - Part 52 edition 11.1999 → replaced by edition 5.2017
General purpose metric ISO threads · Tolerances and profile deviations for multi-start threads
The standard contains specifications for the multi-start thread.
DIN 13 - Part 52 · Edition 11.1990 → replaced by Edition 11.1999
Metric ISO thread · Multiple thread
DIN 13 - supplement 14 edition 3.1944x → replaced by DIN 13 part 51 edition 12.1988
Metric thread Thread for tight fit Non-tight connections (screw-in end of studs)
Also applies to DIN 14.
DIN 13 - Supplement 15 Edition 3.1944x → replaced by DIN 13 Part 51 Edition 12.1988
Metric thread Thread for tight fit Tight connections (screw-in end of studs)
Also applies to DIN 14.
DIN 13 Edition 6.1923 → withdrawn
Metric threads from 1 to 10 mm in diameter
DIN 13 - Supplement 1 · Edition 6.1930 → withdrawn
Metric threads · Dimensions and tolerances fine
also applies to DIN 14
DIN 13 - Supplement 2 · Edition 6.1930 → withdrawn
Metric threads · Fine thread limits
also applies to DIN 14
DIN 13 - Supplement 3 · Edition 6.1930 → withdrawn
Metric threads · Dimensions and tolerances medium and coarse
also applies to DIN 14
DIN 13 - Supplement 4 · Edition 6.1930 → withdrawn
Metric threads · Thread limit dimensions medium and coarse
also applies to DIN 14
DIN 13 - Supplement 5 · Edition 6.1930 → withdrawn
Metric threads · Manufacturing accuracy and thread gauge wear
also applies to DIN 14
DIN 13 - Supplement 6 · Edition 6.1930 → withdrawn
Metric threads · Good thread plug gauge · Limiting sizes fine, medium, coarse
also applies to DIN 14
DIN 13 - Supplement 7 · Edition 6.1930 → withdrawn
Metric threads · Scrap thread plug gauge · Limits fine, medium, coarse
also applies to DIN 14
DIN 13 - Supplement 8 · Edition 6.1930 → withdrawn
Metric thread · Adjustment thread gauge for the wear tester for good thread plug gauge · Limiting dimensions fine, medium, coarse
also applies to DIN 14
DIN 13 - Supplement 9 · Edition 6.1930 → withdrawn
Metric threads · Good thread ring gauge · Limits fine, medium, coarse
also applies to DIN 14
DIN 13 - Supplement 11 · Edition 6.1930 → withdrawn
Metric threads · fitting mandrel and wear test mandrel for good thread ring gauge · limit dimensions fine, medium, coarse
also applies to DIN 14
DIN 13 - Supplement 12 · Edition 6.1930 → withdrawn
Metric threads · Adjustment thread gauge, good and reject · Limits fine, medium, coarse
also applies to DIN 14
DIN 14 - Part 1 · Edition 2.1987 → current
Metric ISO thread · thread less than 1 mm nominal diameter · base profile
The standard applies to the basic profile for metric ISO threads with a nominal diameter of less than 1 mm.
DIN 14 - Part 1 edition 11.1971 → replaced by edition 2.1987
Metric ISO thread · thread less than 1 mm diameter · base profile
DIN 14 - Part 2 · Edition 2.1987 → current
Metric ISO thread · thread less than 1 mm nominal diameter · nominal dimensions
The standard applies to nominal dimensions for metric ISO threads below 1 mm nominal diameter.
DIN 14 - Part 3 · Edition 2.1987 → current
Metric ISO thread · Thread less than 1 mm nominal diameter · Tolerances
The standard applies to tolerances for metric ISO threads below 1 mm nominal diameter.
DIN 14 - Part 4 Edition 2.1987 → current
Metric ISO thread · thread less than 1 mm nominal diameter · limit dimensions
The standard applies to limit values for metric ISO threads with a nominal diameter of less than 1 mm.
DIN 14 - Supplement 14 Edition 3.1944x → replaced by DIN 13 Part 51 Edition 12.1988
Metric thread Thread for tight fit Non-tight connections (screw-in end of studs)
Also applies to DIN 13.
DIN 14 - Supplement 15 Edition 3.1944x → replaced by DIN 13 Part 51 Edition 12.1988
Metric thread thread for tight fit tight connections (screw-in end of studs)
Also applies to DIN 13.
DIN 14 edition 6.1923 → withdrawn
Metric threads from 6 to 149 mm in diameter
DIN 14 - Supplement 1 · Edition 6.1930 → withdrawn
Metric threads · Dimensions and tolerances fine
also applies to DIN 13
DIN 14 - Supplement 2 · Edition 6.1930 → withdrawn
Metric threads · Fine thread limits
also applies to DIN 13
DIN 14 - Supplement 3 · Edition 6.1930 → withdrawn
Metric threads · Dimensions and tolerances medium and coarse
also applies to DIN 13
DIN 14 - Supplement 4 Edition 6.1930 → withdrawn
Metric threads · Thread limit dimensions medium and coarse
also applies to DIN 13
DIN 14 - Supplement 5 · Edition 6.1930 → withdrawn
Metric threads · Manufacturing accuracy and thread gauge wear
also applies to DIN 13
DIN 14 - Supplement 6 · Edition 6.1930 → withdrawn
Metric threads · Good thread plug gauge · Limiting sizes fine, medium, coarse
also applies to DIN 13
DIN 14 - Supplement 7 · Edition 6.1930 → withdrawn
Metric threads · Scrap thread plug gauge · Limits fine, medium, coarse
also applies to DIN 13
DIN 14 - Supplement 8 · Edition 6.1930 → withdrawn
Metric thread · Adjustment thread gauge for the wear tester for good thread plug gauge · Limiting dimensions fine, medium, coarse
also applies to DIN 13
DIN 14 - Supplement 9 · Edition 6.1930 → withdrawn
Metric threads · Good thread ring gauge · Limits fine, medium, coarse
also applies to DIN 13
DIN 14 - Supplement 11 · Edition 6.1930 → withdrawn
Metric threads · fitting mandrel and wear test mandrel for good thread ring gauge · limit dimensions fine, medium, coarse
also applies to DIN 13
DIN 14 - Supplement 12 · Edition 6.1930 → withdrawn
Metric threads · Setting thread gauge good and reject · Limits of fine, medium, coarse
also applies to DIN 13
DIN 15 - Part 1 Edition 6.1984 → replaced by DIN ISO 128 Part 20 Edition 12.1997
Technical drawings · Lines · Basics
DIN 15 - Part 1 · Edition 12.1967 → replaced by Edition 6.1984 and DIN 15 Part 2 Edition 6.1984
Lines in drawings · Line types, line widths, application
DIN 15 - Part 1 · Edition 6.1955 → withdrawn
Drawings · Lines
DIN 15 - Part 2 Edition 6.1984 → replaced by DIN ISO 128 Part 24 Edition 12.1999
Technical drawings · Lines · General use
DIN 15 - Part 2 · Edition 6.1968 → replaced by Edition 6.1984
Lines in drawings · Application examples
DIN 15 - Part 2 · Edition 6.1955 → withdrawn
Drawings · Lines · Application examples
DIN 15 - Part 3 · Edition 5.1986 → replaced by DIN ISO 128 Part 25 Edition 6.2000
Technical drawings · Lines · Application in the representation of the ship's hull
DIN 15 edition 8.1921 → withdrawn
Drawings · Lines
DIN 16 - Part 1 · Edition 12.1967 → replaced by DIN 6776 Part 1 Edition 4.1976 and DIN 6776 Part 1 Supplementary sheets 1 and 2 Edition 4.1976
Angled standard font for drawings · General, font sizes
DIN 16 - Part 2 · Edition 12.1967 → replaced by DIN 6776 Part 1 Edition 4.1976 and DIN 6776 Part 1 Supplementary sheets 1 and 2 Edition 4.1976
Angled standard font for drawings · Medium font
DIN 16 - Part 3 · Edition 12.1967 → replaced by DIN 6776 Part 1 Edition 4.1976 and DIN 6776 Part 1 Supplementary sheets 1 and 2 Edition 4.1976
Angled standard font for drawings · Narrow font
DIN 16 edition 8.1940 → replaced by DIN 16 parts 1, 2 and 3 edition 12.1967
Angled standard script written with auxiliary net
DIN 16 edition 4.1934 → replaced by edition 8.1940
Drawings - Annotations - Examples · Auxiliary nets
DIN 16 - Part 1 edition 10.1922 → replaced by DIN 16 edition 4.1934
Drawings · Slanted block letters · Letters and numbers
DIN 16 - Part 1 · Edition 8.1922 → replaced by Edition 10.1922
Drawings · Slanted block letters · Letters and numbers
DIN 16 - Part 1 · Edition 7.1919 → replaced by Edition 8.1922
Drawings · Slanted block letters · Letters and numbers
DIN 16 - Part 2 Edition 10.1922 → replaced by DIN 16 Edition 4.1934
Drawings · Slanted block letters · Font sizes
DIN 16 - Part 2 · Edition 7.1919 → replaced by Edition 10.1922
Drawings · Slanted block letters · Font sizes
DIN 17 - Part 1 · Edition 12.1967 → replaced by DIN 6776 Part 1 Edition 4.1976 and DIN 6776 Part 1 Supplementary sheets 1 and 2 Edition 4.1976
Vertical standard font for drawings · General, font sizes
DIN 17 - Part 2 · Edition 12.1967 → replaced by DIN 6776 Part 1 Edition 4.1976 and DIN 6776 Part 1 Supplementary sheets 1 and 2 Edition 4.1976
Vertical standard font for drawings · Medium font
DIN 17 - Part 3 · Edition 12.1967 → replaced by DIN 6776 Part 1 Edition 4.1976 and DIN 6776 Part 1 Supplementary sheets 1 and 2 Edition 4.1976
Vertical standard font for drawings · Narrow font
DIN 17 edition 8.1940 → replaced by DIN 17 parts 1, 2 and 3 edition 12.1967
Vertical standard font written with auxiliary net
2nd edition of the standard; Nominal size 12.5 changed to 12
DIN 17 · Edition 6.1938 → replaced by Edition 8.1940
Drawings · Vertical standard font for lettering on signs etc. Like. · Written with auxiliary network
DIN 18 edition 1.1928 → withdrawn
Noble bore eB, standard bore
DIN 18 edition 5.1923 → withdrawn
Fine bore (fine fit, unit bore)
DIN 19 edition 5.1923 → withdrawn
Fine bore B, standard bore
DIN 20 edition 5.1923 → withdrawn
Slight running fit LL, fine fit, standard bore
DIN 21 edition 5.1923 → withdrawn
Running fit L, fine fit, unit bore
DIN 22 edition 5.1923 → withdrawn
Closely. Running fit, fine fit, unit bore
DIN 23 edition 1.1928 → withdrawn
Sliding fit G, fine fit, unit bore
DIN 23 edition 5.1923 → withdrawn
Sliding seat G
DIN 24 edition 1.1928 → withdrawn
Sliding fit S, fine fit, unit bore
DIN 24 edition 5.1923 → withdrawn
Sliding seat S
DIN 25 edition 1.1928 → withdrawn
Adhesive fit H, fine fit, unit bore
DIN 25 · Edition 5.1923 → withdrawn
Detention seat H
DIN 26 edition 1.1928 → withdrawn
Interference fit F, fine fit, unit bore
DIN 26 edition 5.1923 → withdrawn
Tight fit F
DIN 27 edition 3.1967 → withdrawn
Representation of threads, bolts and nuts
DIN 27 edition 9.1955 → withdrawn
Representation of threads, bolts and nuts
DIN 27 Edition 5.1920 → withdrawn
Screws, symbols
DIN 28 - Part 1 · Edition 7.1923 → withdrawn
Drawings, title block and parts list, general
DIN 28 - Part 2 · Edition 11.1920 → withdrawn
Drawings, title block and parts list, general information, samples 1
DIN 28 - Part 3 · Edition 11.1920 → withdrawn
Drawings, title block and parts list, general, samples 2 to 8
DIN 28 - Part 4 Edition 11.1920 → withdrawn
Drawings, title block and parts list, general, samples 2 to 8
DIN 28 - Part 5 Edition 7.1923 → withdrawn
Drawings, title block and parts list, general, samples 2 to 8
DIN 29 edition 12.1961 → withdrawn
Representation and symbols for feathers
DIN 29 edition 10.1923 → withdrawn
Helical, conical, leaf and spiral springs; Symbols
DIN 30 edition 12.1970 → replaced by DIN ISO 6410 part 3 edition 12.1993
Drawings · Simplified representations
DIN 30 - Part 5 · Edition 4.2002 → current
Technical drawings - drawing simplification · Third-party part drawings, execution
The standard applies to the documentation of non-standardized, commercially available items for ordering purposes.
DIN 30 - Part 5 · Edition 9.1976 → replaced by Edition 4.2002
Simplified information in technical documents · Simplified drawing, third-party part drawings, execution
The standard applies to the documentation of non-standardized, commercially available items for ordering purposes.
DIN 30 - Part 6 · Edition 12.2002 → current
This standard applies to the manual or computer-aided creation of drawings to depict similar objects, parts or groups of different designs.
DIN 30 - Part 6 · Edition 4.1975 → replaced by Edition 12.2002
Simplified information in technical documents · Simplified drawings, collective drawings, execution
DIN 30 - Part 7 · Edition 4.1975 → 5.2002 withdrawn without replacement
Simplified information in technical documents · Simplified drawings, pre-printed drawings, execution
DIN 30 - Part 8 Edition 3.1978 → 2.1999 withdrawn without replacement
Simplified information in technical documents · Simplified drawings, supplementary drawings, execution
DIN 30 - Part 10 · Edition 1.2006 → current
Simplified information in technical documents - simplified drawing · Simplified information and collective information, design
The standard defines the rules for the uniform creation and structuring of simplified information and collective information on required technical properties and their entry in drawings.
DIN 30 - Part 10 · Edition 11.1998 → replaced by Edition 1.2006
Simplified information in technical documents - simplified drawing · Simplified information and collective information, design
The standard contains regulations for the uniform formation and structuring of simplified information and collective information on required technical properties and their entry in drawings.
DIN 30 edition 8.1940x → withdrawn
Drawings, simplifications for small representations
DIN 30 edition 8.1940 → withdrawn
Drawings, simplifications for small representations
DIN 31 edition 4.1951 → withdrawn
DIN, name DIN, association symbol DIN
The standard contains the symbol statutes of the DNA with rules for the use of the association symbol.
DIN 31 - Supplement 1 · Edition 4.1951 → withdrawn
Association symbol DIN · prototype for enlargement and reduction
DIN 31 edition 9.1934 → withdrawn
DIN mark, guidelines for marking standardized products
The standard contains the symbol statutes of the DNA with rules for the use of the association symbol.
DIN 31 - Supplement · Edition 9.1934 → withdrawn
DIN symbol, archetype for enlargement and reduction
DIN 32 - Part 1 · Edition 2.1985 → withdrawn without replacement
Packaging · Packaging for prepackages · Folding lid cans, round, cylindrical, 2 or 3 parts
DIN 32 - Part 1 · Edition 5.1973 → replaced by Edition 2.1985
Packaging · Packaging for prepackaging · Metal cans
DIN 32 - Part 3 · Edition 2.1981 → withdrawn without replacement
Packaging · Packaging for prepackages · Determination of the dimensions of boxes for tubes
DIN 32 - Part 3 · Edition 1.1979 → replaced by Edition 2.1981
Packaging · Packaging for prepackages · Determination of the dimensions of boxes for tubes
DIN 32 - part 4 edition 5.1980 → 6.2005 withdrawn without replacement
Packaging · Packaging for prepackages · Volume deviations
DIN 32 - Part 5 Edition 3.1983 → 6.2011 withdrawn without replacement
Packaging · Packaging for prepackages · Container volume of adhesive packs
DIN 32 - Part 5 · Edition 2.1981 → replaced by Edition 3.1983
Packaging · Packaging for prepackages · Container volume of adhesive packs
DIN 33 - Part 1 · Edition 7.1927 → withdrawn
Water turbines, names, free jet turbines
DIN 33 - Part 2 · Edition 7.1927 → withdrawn
Water Turbines, Designations, Standing Turbines
DIN 33 - Part 3 · Edition 7.1927 → withdrawn
Water turbines, designations, horizontal turbines
DIN 33 - Part 4 Edition 7.1927 → withdrawn
Water turbines, designations, horizontal boiler turbines
DIN 33 - Part 5 · Edition 7.1927 → withdrawn
Water turbines, names, horizontal spiral turbines
DIN 34 edition 1.1998 → replaced by DIN ISO 16016 edition 5.2002
Technical product documentation - Protection notices for restricting the use of documents and products
DIN 34 edition 10.1977 → replaced by edition 1.1998
Protection notice on the restriction of the use of documents
DIN 34 edition 8.1956 → replaced by edition 10.1977
Copyright notice
DIN 34 edition 3.1933 → withdrawn
Copyright stamp or copyright notice
DIN 34 edition 4.1927 → withdrawn
Copyright stamp or copyright notice
DIN 35 · Edition 6.1938 → withdrawn
Metallic materials, weights in kg / dm³, calculation values
DIN 36 edition 10.1922 → withdrawn
Drawings · Fracture lines, cutting course, cutting surfaces
DIN 37 edition 12.1961 → replaced by DIN ISO 2203 edition 6.1976
Representation and simplified representation for gears and gear pairing
DIN 37 · Edition 2.1921 → withdrawn
Drawings · Gears, symbols
DIN 38 Edition 12.1983 → current
Plain bearings · Bearing metal spout in thick-walled composite plain bearings
DIN 38 edition 11.1975 → replaced by edition 12.1983
Bearing metal spout in plain bearings
DIN 39 edition 10.2003 → current
Fixed ball handles
The standard specifies dimensions and materials for fixed ball handles. Fixed ball handles are mainly used on handwheels according to DIN 950, DIN 3319 or hand cranks according to DIN 468 and DIN 469.
DIN 39 edition 10.1962 → replaced by edition 10.2003
Fixed ball handles
DIN 39 Edition 3.1954 → withdrawn
Fixed ball handles
DIN 39 Edition 10.1927 → withdrawn
Fixed ball handles
DIN 39 - Supplement · Edition 6.1921 → withdrawn
Fixed ball handles
DIN 39 edition 11.1919 → withdrawn
Fixed ball handles
DIN 40 edition 1.1928 → withdrawn
Fine wave W, standard wave
DIN 40 · Edition 5.1923 → withdrawn
Fine wave (fine and fine fit, standard wave)
DIN 41 · Edition 5.1923 → withdrawn
Slight running fit LL, fine fit, standard shaft
DIN 42 edition 5.1923 → withdrawn
Running fit L, fine fit, standard shaft
DIN 43 · Edition 5.1923 → withdrawn
Closely. Running fit EL, fine fit, standard shaft
DIN 44 · Edition 5.1923 → withdrawn
Sliding fit G, fine fit, unit shaft
DIN 45 · Edition 5.1923 → withdrawn
Sliding seat S, fine fit, standard shaft
DIN 46 edition 5.1923 → withdrawn
Adhesive fit H, fine fit, standard shaft
DIN 47 edition 5.1923 → withdrawn
Interference fit F, fine fit, unit shaft
DIN 48 edition 1.1928 → withdrawn
Edelgleitsitz eG, noble fit, standard shaft
DIN 48 · Edition 5.1923 → withdrawn
Edelgleitsitz eG, noble fit, standard shaft
DIN 49 edition 1.1928 → withdrawn
Noble sliding seat eS, noble fit, standard shaft
DIN 49 edition 5.1923 → withdrawn
Noble sliding seat eS, noble fit, standard shaft
DIN 50 edition 1.1928 → withdrawn
Noble seat eH, noble fit, standard shaft
DIN 50 · Edition 5.1923 → withdrawn
Noble seat eH, noble fit, standard shaft
DIN 51 edition 1.1928 → withdrawn
Edelfestsitz eF, Edelpfit, unit shaft
DIN 51 edition 5.1923 → withdrawn
Edelfestsitz eF, Edelpfit, unit shaft
DIN 52 edition 5.1923 → withdrawn
Wide running fit WL, fine fit, standard bore
DIN 53 · Edition 5.1923 → withdrawn
Wide running fit WL, fine fit, standard shaft
DIN 54 edition 3.1923 → withdrawn
Press fit P, precision fit, unit bore
DIN 55 edition 3.1923 → withdrawn
Interference fit P, precision fit, unit shaft
DIN 56 edition 1.1928 → withdrawn
Noble drive seat eT, high-grade fit, standard shaft
DIN 56 edition 3.1923 → withdrawn
Noble drive seat eT, high-grade fit, standard shaft
DIN 57 edition 3.1923 → withdrawn
Drive seat T, fine fit, standard shaft
DIN 58 · Edition 1.1928 → withdrawn
Drive seat T, fine fit, unit bore
DIN 58 Edition 3.1923 → withdrawn
Drive seat T, fine fit, unit bore
DIN 60 edition 7.1923 → withdrawn
Grinding allowances for unhardened turned shafts
DIN 61 edition 7.1926 → 1.1931 withdrawn
Bare hexagon bolts for 1 nut or 1 castle nut 1 d from 1/4 "to 2" (for selection see DIN WAN 170, DIN LON 302)
DIN 61 edition 8.1924 → withdrawn
Bare hexagon head bolts for 1 nut or 1 castle nut, Whitworth thread
DIN 62 edition 7.1926 → 1.1931 withdrawn
Bare hexagon bolts for 2 nuts 1 d from 1/4 "to 2" (for selection see DIN LON 303)
DIN 62 edition 6.1922 → withdrawn
Bare hexagon bolts for 2 nuts, Whitworth thread
DIN 63 · Edition 5.1972 → 3.1994 withdrawn without replacement
Countersunk screws with slot, small head (countersunk heads previous form)
DIN 63 edition 12.1952 → withdrawn
Countersunk head screws with longitudinal slot, small head, metric thread, metric fine thread
DIN 63 edition 10.1942 → withdrawn
Countersunk screws; with small head, M 1 to M 10
DIN 63 edition 2.1930 → withdrawn
Countersunk screws with small head, metric thread
DIN 64 · Edition 1.1956 → withdrawn
Cheese head screws with longitudinal slot, 1/2 "to 1 1/2"
DIN 64 · Edition 1.1926 → withdrawn
Cheese head screws; upper head edge sharp, 1/2 "to 1 1/2"
DIN 65 · Edition 1.1926 → withdrawn
Bare countersunk screws, upper head edge round
DIN 66 edition 4.1990 → replaced by DIN EN ISO 15065 edition 5.2005
Countersink for countersunk screws with standard heads according to DIN ISO 7721
The standard specifies the dimensions, designation and design of countersinks for countersunk screws with an ISO standard head.
DIN 67 edition 1.1926 → withdrawn
Button head screws from 1/4 "to 3/4"
DIN 68 · Edition 1.1956 → withdrawn
Countersunk screws with longitudinal slot, 1/2 "to 1"
DIN 68 · Edition 1.1926 → withdrawn
Bare countersunk screws from 1/4 "to 1"
For selection see DIN WAN 173, DIN LON 330
DIN 69 edition 8.1971 → replaced by DIN ISO 273 edition 9.1979
Through holes for screws and similar threaded and molded parts
DIN 69 · Edition 5.1943 → withdrawn
Through holes for screws or similar parts with metric thread and metric fine thread
DIN 69 · Edition 9.1930 → withdrawn
Through holes for screws
2nd edition of the standard
DIN 69 · Edition 5.1924 → withdrawn
Through holes for screws
DIN 70 - Part 1 · Edition 12.1946 → withdrawn
Bolts, nuts and similar threaded parts · Selection, general
DIN 70 - Part 1 · Edition 12.1920 → withdrawn
Bare hex nuts 1 d of 1/4 "÷ 2" Whitworth threads
DIN 70 - Part 2 · Edition 9.1944 → withdrawn
Screws, nuts and similar threaded parts · Selection for all areas of application
DIN 70 - Part 2 · Edition 10.1922 → withdrawn
Bare hex nuts 1d by 2 1/4 "÷ 6" Whitworth threads
DIN 71 edition 8.1922 → withdrawn
Bare castle nuts 1 d, Whitworth thread
DIN 73 · Edition 8.1922 → withdrawn
Bare low castle nuts, Whitworth threads
DIN 74 · Edition 4.2003 → current
Countersinks for countersunk screws with the exception of countersunk screws with heads according to DIN EN 27721
The standard specifies the dimensions of countersinks for countersunk screws, with the exception of countersunk screws with heads according to DIN EN 27721, and their designation.
DIN 74 - Part 1 edition 11.2000 → replaced by DIN 74 edition 4.2003
Countersinks for countersunk screws (except countersunk screws with heads according to DIN EN 27721)
The standard specifies the dimensions of countersinks for countersunk screws.
DIN 74 - Part 1 · Edition 12.1980 → replaced by Edition 11.2000
Countersinks for countersunk screws
DIN 74 - Part 1 · Edition 7.1971 → replaced by Edition 12.1980
Countersinks for countersunk screws
DIN 74 - Part 2 Edition 5.1991 → 10.1998 withdrawn without replacement
Countersinks for screws with cylinder head
DIN 74 - Part 2 · Edition 12.1980 → replaced by Edition 5.1991
Countersinks for screws with cylinder head
DIN 74 - Part 2 · Edition 7.1971 → replaced by Edition 12.1980
Countersinks for screws with cylinder head
DIN 74 - Part 3 · Edition 5.1991 → 10.1998 withdrawn without replacement
Countersinks for hexagon bolts and nuts
DIN 74 - Part 3 · Edition 12.1972 → replaced by Edition 5.1991
Countersinks for hexagon bolts and nuts
DIN 75 - Part 1 · Edition 4.1972 → 10.1998 withdrawn without replacement
Countersinks for countersunk screws
DIN 75 - Part 1 · Edition 2.1954 → withdrawn
Countersinks for countersunk screws
DIN 75 - Part 2 · Edition 2.1956 → withdrawn
Countersinks for cylinder screws
DIN 75 · Edition 1.1942 → withdrawn
Countersinks for screws
DIN 76 - Part 1 · Edition 8.2016 → current
Thread run-outs and thread undercuts · For metric ISO threads according to DIN 13-1
The standard specifies thread run-outs and thread undercuts for screws and similar parts as well as for parts with internal thread (thread root holes) with metric ISO thread (regular and fine thread) according to DIN 13 Part 1 and DIN ISO 261 and the associated standard designations.
DIN 76 - Part 1 · Edition 6.2004 → replaced by Edition 8.2016
Thread runouts, thread undercuts for metric ISO threads according to DIN 13-1
DIN 76 - Part 1 · Edition 12.1983 → replaced by Edition 6.2004
Thread runouts, thread undercuts for metric ISO thread according to DIN 13
DIN 76 - Part 1 · Edition 9.1975 → replaced by Edition 12.1983
Thread runouts, thread undercuts for metric ISO threads according to DIN 13
DIN 76 - Part 1 · Edition 6.1967 → replaced by Edition 9.1975
Thread runout; Thread grooves for metric threads
DIN 76 - Part 1 edition 11.1953 → withdrawn
Thread run-out, thread grooves, thread ends, for threads with metric profile
DIN 76 - Part 1 · Edition 4.1943 → withdrawn
Thread runout, thread grooves; Metric thread
DIN 76 - Part 2 Edition 12.1984 → current
Thread run-outs, thread undercuts · For pipe threads according to DIN ISO 228 Part 1
The standard contains specifications about thread run-outs and thread undercuts for parts with cylindrical pipe threads according to DIN ISO 228 Part 1.
DIN 76 - Part 2 · Edition 11.1953 → replaced by Edition 12.1984
Thread run-out, thread grooves, thread ends for Whitworth threads and Whitworth pipe threads
DIN 76 - Part 2 · Edition 4.1943 → withdrawn
Thread runout, thread grooves; Whitworth threads and Whitworth pipe threads
DIN 76 - Part 3 · Edition 1.1977 → current
Thread runouts, thread undercuts · For trapezoidal, buttress and round threads and other threads with a coarse pitch
DIN 76 edition 9.1924 → withdrawn
Thread run-out thread grooves, guidelines
DIN 77 edition 4.1924 → withdrawn
Thread lengths for the nut side
Bolts, nuts and accessories - general.
DIN 78 · Edition 4.2013 → current
Screw protrusions
The standard defines the thread protrusion for screws.
DIN 78 edition 3.2001 → replaced by edition 4.2013
Screw protrusions
DIN 78 edition 12.1983 → replaced by edition 3.2001 and DIN EN ISO 4753
Thread ends, screw protrusions for metric ISO threads according to DIN 13
DIN 78 edition 9.1975 → replaced by edition 12.1983
Thread ends, screw protrusions for metric ISO threads according to DIN 13
DIN 78 edition 8.1953 → withdrawn
Screw ends, screw protrusions
DIN 78 - Part 1 · Edition 9.1965 → replaced by DIN 78 Edition 9.1975
Thread ends Screw protrusions · Thread with metric profile
DIN 78 - Part 1 · Edition 7.1929 → withdrawn
Screw ends for metric threads from M 1 to M 154
3rd edition of the standard.
DIN 78 - Part 1 · Edition 4.1925 → withdrawn
Screw ends; Roundings and core approaches
DIN 78 - Part 2 · Edition 7.1929 → withdrawn
Screw ends for metric threads from M 1 to M 10, Whitworth threads from 1/4 "to 6"
3rd edition of the standard.
DIN 78 - Part 2 · Edition 2.1923 → withdrawn
Screw ends; Tapered points and split ends
DIN 79 · Edition 2.2013 → current
Square edge for spindles and operating parts
The standard defines dimensions and tolerance classes for outside and inside square edges. The squares are used for spindles and operating parts such as handwheels, hand cranks or handles.
DIN 79 edition 10.2004 → replaced by edition 2.2013
Square edge for spindles and operating parts
The standard specifies dimensions for the outer and inner square. The squares are used for spindles and operating parts such as handwheels, hand cranks or handles.
DIN 79 edition 8.1971 → replaced by edition 10.2004
Square edge for spindles and operating parts
DIN 79 - Part 1 · Edition 4.1927 → replaced by DIN 79 Edition 8.1971
Square edge and square holes for spindles, handwheels and cranks · Workpiece
DIN 79 - Part 2 · Edition 4.1927 → replaced by DIN 79 Edition 8.1971
Square edge and square holes for spindles, handwheels and cranks · Working gauges, dimensions
DIN 79 - Part 3 · Edition 4.1927 → replaced by DIN 79 Edition 8.1971
Square edges and square holes for spindles, handwheels and cranks · Working gauges, manufacturing accuracy and wear
DIN 80 edition 7.1926 → 1.1931 withdrawn
Bare hexagon bolts for 1 nut or 1 castle nut 1 d from M 11 to M 52
DIN 80 edition 8.1921
Bare hexagon bolts for 1 nut, metric thread
DIN 81 - Part 1 Edition 12.1921 → 1.1931 withdrawn
Bare hexagon bolts M 1.7 to M 10
DIN 81 - Part 2 Edition 7.1926 → 1.1931 withdrawn
Bare hexagon bolts M 11 to M 52
DIN 81 - Part 2 · Edition 8.1921 → withdrawn
Bare hexagon head bolts for 2 nuts or 1 castle nut with 11 ÷ 52 mm metric thread
DIN 82 edition 1.1973 → current
Knurl
DIN 82 edition 1.1940 → replaced by edition 1.1973
Knurled and cord divisions
DIN 82 edition 1.1927 → replaced by edition 1.1940
Knurled and cord divisions
DIN 82 edition 3.1924 → withdrawn
Knurled and cord divisions
DIN 83 - Part 1 · Edition 3.1924 → withdrawn
Bare countersunk screws, upper head edge round, from M 1 to M 10
DIN 83 - Part 2 Issue 3.1924 → withdrawn
Bare countersunk screws, upper head edge round, from M 11 to M 36
DIN 84 edition 8.1990 → replaced by DIN EN ISO 1207 edition 10.1994
Cylinder screws with slot, product class A
DIN 84 edition 10.1988 → replaced by edition 8.1990
Socket head cap screws with slot; Product class A
DIN 84 edition 10.1970 → replaced by edition 10.1988
Cylinder screws with slot
DIN 84 edition 12.1952 → withdrawn
Cheese head screws; upper head edge sharp, with longitudinal slot, metric thread, metric fine thread
DIN 84 edition 10.1942x → withdrawn
Cheese head screws; M 1 to M 36
Unchanged summary of part 1 edition 10.1942 and part 2 edition 4.1943
DIN 84 - Part 1 · Edition 3.1924 → withdrawn
Cheese head screws, upper head edge sharp, from M 1 to M 10
DIN 84 - Part 2 · Edition 3.1924 → withdrawn
Cheese head screws, upper head edge sharp, from M 11 to M 36
DIN 85 edition 8.1990 → replaced by DIN EN ISO 1580 edition 10.1994
Flat head screws with slot · Product class A
DIN 85 edition 10.1988 → replaced by edition 8.1990
Flat head screws with slot · Product class A
DIN 85 edition 12.1972 → replaced by edition 10.1988
Flat head screws with slot
DIN 85 · Edition 6.1970 → replaced by Edition 12.1972
Flat head screws with slot
DIN 85 edition 4.1964 → replaced by edition 6.1970
Pan head screws with slotted M 1 to M 10
DIN 85 edition 12.1952 → replaced by edition 4.1964
Pan head screws with longitudinal slot, metric thread, metric fine thread
DIN 85 edition 10.1942 → replaced by edition 12.1952
Oval head screws; M 1 to M 10
DIN 85 edition 1.1937 → replaced by edition 10.1942
Bare oval head screws from M 1 to M 10
DIN 85 edition 1.1926 → replaced by edition 1.1937
Bare oval head screws from M 1 to M 10
DIN 86 · Edition 4.1964 → withdrawn without replacement
Pan head screws with slot
DIN 86 edition 12.1952 → withdrawn
Button-head screws with longitudinal slot, metric thread, metric fine thread
DIN 86 Edition 10.1942 → withdrawn
Button-head screws; M 1 to M 20
DIN 86 - Part 1 · Edition 8.1921 → withdrawn
Bare button-head screws, metric thread, from M 1 to M 10
DIN 86 - Part 2 · Edition 8.1921 → withdrawn
Bare button-head screws, metric thread, from M 11 to M 20
DIN 87 · Edition 5.1972 → 11.1989 withdrawn without replacement
Slotted countersunk screws; large head (countersunk heads previous shape)
DIN 87 · Edition 12.1952 → withdrawn
Countersunk screws with longitudinal slot, large head, M 3 to M 10 and M 8x1 to M 10x1
DIN 87 - Part 1 · Edition 10.1942 → withdrawn
Countersunk screws; M 1 to M 10
DIN 87 - Part 2 Edition 10.1942 → withdrawn
Countersunk screws; M 12 to M 52
DIN 87 - Part 1 · Edition 1.1926 → withdrawn
Bare countersunk screws from M 1 to M 10
DIN 87 - Part 2 · Edition 8.1921 → withdrawn
Bare countersunk screws from M 11 to M 27
DIN 88 edition 5.1972 → 11.1989 withdrawn without replacement
Slotted raised countersunk head screws; large head (raised countersunk heads previous shape)
DIN 88 · Edition 4.1964 → replaced by Edition 5.1972 → withdrawn
Slotted raised countersunk head screws, large head
DIN 88 edition 12.1952 → withdrawn
Raised countersunk head screws with longitudinal slot, large head, metric thread, metric fine thread
DIN 88 edition 10.1942x → withdrawn
Raised countersunk head screws; M 1 to M 52
Unchanged summary of part 1 edition 10.1942 and part 2 edition 1.1943
DIN 88 edition 1.1926 → withdrawn
Bare raised countersunk head screws from M 1 to M 10
DIN 89 - Part 1 · Edition 10.1925 → withdrawn
Bare hex nuts from 1.7 ÷ 52 mm metric thread
DIN 89 - Part 2 Edition 10.1922 → replaced by DIN 934 Part 1 Edition 1.1926
Bare hexagon nuts from 56 ÷ 149 mm metric thread
DIN 90 - Part 1 Edition 10.1922 → replaced by DIN 935 Part 1 Edition 1.1926
Bare castle nuts from 4 to 11 mm metric thread
DIN 90 - Part 2 Edition 7.1924 → replaced by DIN 935 Part 1 Edition 1.1926
Bare low castle nuts of 12 ÷ 52 mm metric thread
DIN 91 edition 5.1972 → 11.1989 withdrawn without replacement
Slotted raised countersunk head screws; small head (raised countersunk heads previous shape)
DIN 91 edition 4.1964 → replaced by edition 5.1972
Slotted raised countersunk head screws, small head
DIN 91 edition 12.1952 → withdrawn
Raised countersunk head screws with longitudinal slot, small head, metric thread, metric fine thread
DIN 91 edition 10.1942 → withdrawn
Raised countersunk head screws; with small head, M 1 to M 10
DIN 91 edition 2.1930 → withdrawn
Bare raised countersunk head screws with small head M 1 to M 10
DIN 92 Edition 3.1923 → withdrawn
Distribution of split pins and tapered pins to bolt and screw diameters
DIN 93 edition 7.1974 → 5.2003 withdrawn without replacement
Washers with rags (locking plates with rags)
DIN 93 · Edition 2.1954 → withdrawn
Locking plates; with rag
DIN 93 · Edition 5.1943 → withdrawn
Lock washers with rags
DIN 93 Edition 10.1925 → withdrawn
Lock washers with rags
DIN 94 Edition 9.1983 → 3.1998 replaced by DIN EN ISO 1234
Split pins
DIN 94 edition 10.1972 → withdrawn
Split pins
DIN 94 edition 8.1939 → withdrawn
Split pins
DIN 94 edition 10.1925 → withdrawn
Split pins
DIN 95 · Edition 12.2016 → current
Slotted raised countersunk wood screws
The standard specifies the properties of raised countersunk wood screws with a slot for thread diameters from 1.6 to 8 mm that are used outside of areas that require approval.
DIN 95 edition 12.2010 → replaced by edition 12.2016
Slotted raised countersunk wood screws
The standard contains the relevant specifications and technical delivery conditions for slotted raised countersunk wood screws and specifies their designation.
DIN 95 edition 12.1986 → replaced by edition 12.2010
Slotted raised countersunk wood screws
DIN 95 edition 3.1975 → replaced by edition 12.1986
Slotted raised countersunk wood screws
DIN 95 · Edition 9.1953 → withdrawn
Raised countersunk wood screws with longitudinal slot
DIN 95 edition 12.1943 → withdrawn
Raised countersunk head wood screws
DIN 95 edition 8.1924 → withdrawn
Raised countersunk head wood screws
DIN 96 Edition 12.2016 → current
Slotted button-head wood screws
The standard contains the dimensional specifications and technical delivery conditions for button-head wood screws with slot and specifies their designation.
DIN 96 edition 12.2010 → replaced by edition 12.2016
Slotted button-head wood screws
DIN 96 edition 12.1986 → replaced by edition 12.2010
Slotted button-head wood screws
DIN 96 edition 3.1975 → replaced by edition 12.1986
Slotted button-head wood screws
DIN 96 edition 9.1953 → withdrawn
Button-head wood screws with a longitudinal slot
DIN 96 edition 12.1943 → withdrawn
Button-head wood screws
DIN 96 edition 8.1924 → withdrawn
Button-head wood screws
DIN 97 · Edition 12.2016 → current
Countersunk wood screws with slot
The standard contains the dimensional specifications and technical delivery conditions for slotted countersunk wood screws and specifies their designation.
DIN 97 edition 12.2010 → replaced by edition 12.2016
Countersunk wood screws with slot
DIN 97 edition 12.1986 → replaced by edition 12.2010
Countersunk wood screws with slot
DIN 97 edition 3.1975 → replaced by edition 12.1986
Countersunk wood screws with slot
DIN 97 edition 10.1953 → withdrawn
Countersunk wood screws with a longitudinal slot
DIN 97 edition 12.1943 → withdrawn
Countersunk wood screws
DIN 97 edition 8.1924 → withdrawn
Countersunk wood screws
DIN 98 Edition 10.2003 → current
Rotatable ball handles
The standard specifies the dimensions and materials for rotating ball handles. These are mainly used on handwheels according to DIN 950, DIN 3319 or hand cranks according to DIN 468 and DIN 469.
DIN 98 edition 10.1962 → replaced by edition 10.2003
Rotatable ball handles
DIN 98 · Edition 1.1928 → withdrawn
Rotatable ball handles
DIN 98 edition 11.1919 → withdrawn
Rotatable ball handles
DIN 99 edition 11.2015 → current
Conical handles
The standard applies to tapered steel handles with a thread or bore hole for the handles. The standard contains dimensions and information about the material and design of the tapered handles.
DIN 99 edition 1.1996 → replaced by edition 11.2015
Conical handles
The standard applies to steel tapered handles.
DIN 99 edition 6.1972 → replaced by edition 1.1996
Conical handles
DIN 99 edition 1.1937 → withdrawn
Ball handles
DIN 99 edition 4.1927 → withdrawn
Ball handles
DIN 99 edition 3.1920 → withdrawn
Ball handles
DIN 101 · Edition 2.2011 → current
Rivet · Technical delivery conditions
The standard contains requirements, tolerances and tests for rivets.
DIN 101 · Edition 5.1993 → replaced by Edition 2.2011
Rivet; Technical delivery conditions
DIN 101 edition 7.1977 → replaced by edition 5.1993
Rivet; Technical delivery conditions
DIN 101 edition 8.1969 → withdrawn
Rivet; Technical delivery conditions
DIN 101 edition 12.1954 → withdrawn
Steel rivets 10 mm in diameter and over; Technical delivery conditions
DIN 102 edition 10.1956 → replaced by DIN EN ISO 1 edition 10.2002
Reference temperature of the measuring tools and workpieces
DIN 102 Edition 7.1921 → withdrawn
Reference temperature of the measuring tools and workpieces
DIN 103 - Part 1 · Edition 4.1977 → current
ISO metric trapezoidal thread; Thread profiles
DIN 103 - Part 1 · Edition 8.1970 → replaced by Edition 4.1977
ISO metric trapezoidal thread; Thread profiles
DIN 103 - Part 2 · Edition 4.1977 → current
ISO metric trapezoidal thread; Thread rows
DIN 103 - Part 2 · Edition 8.1970 → replaced by Edition 4.1977
ISO metric trapezoidal thread; Thread rows
DIN 103 - Part 3 · Edition 4.1977 → current
ISO metric trapezoidal thread; Dimensions and tolerances for trapezoidal threads of general use
DIN 103 - Part 4 · Edition 4.1977 → current
ISO metric trapezoidal thread; Nominal dimensions
DIN 103 - Part 4 · Edition 12.1971 → replaced by Edition 4.1977
ISO metric trapezoidal thread; Nominal dimensions
DIN 103 - Part 5 · Edition 10.1972 → current
ISO metric trapezoidal thread; Limit dimensions for nut threads from 8 to 100 mm nominal diameter
DIN 103 - Part 6 Edition 10.1972 → current
ISO metric trapezoidal thread; Limit dimensions for nut threads from 105 to 300 mm nominal diameter
DIN 103 - Part 7 · Edition 10.1972 → current
ISO metric trapezoidal thread; Limit dimensions for bolt threads from 8 to 100 mm nominal diameter
DIN 103 - Part 8 Edition 10.1972 → current
ISO metric trapezoidal thread; Limit dimensions for bolt threads from 105 to 300 mm nominal diameter
DIN 103 - Part 9 · Edition 2.1985 → current
ISO metric trapezoidal thread; Gauges for bolt and nut threads; Gauge dimensions and construction features
The standard specifies the gauge dimensions and construction characteristics necessary for the production of gauges for the ISO metric trapezoidal thread. Other test methods for trapezoidal threads are not standardized. The teaching system according to the standard is generally considered to be arbitration.
DIN 103 edition 8.1924 → withdrawn
Trapezoidal thread, catchy
DIN 104 · Edition 1.1952x → withdrawn without replacement
Wood beam ceilings; Beams on two supports; calculation
DIN 104 - Part 1 · Edition 1.1952 → withdrawn
Wood beam ceilings; Beams on two supports; calculation
DIN 104 - Part 1 · Edition 3.1920 → withdrawn
Wooden beams for small houses, types of ceilings
DIN 104 - Part 2 · Edition 3.1954 → withdrawn
Wooden beams, walk-through beams on 3 supports
DIN 104 - Part 2 · Edition 3.1920 → withdrawn
Wooden beams for small houses, cross sections
DIN 104 - Part 3 · Edition 3.1920 → withdrawn
Wooden beams for small houses, curve board for determining the permissible cross-sections
DIN 104 - Supplement · Edition 11.1920 → withdrawn
Supplement to part 1-3 Wooden beams for small houses
DIN V 105 - Part 1 Pre-standard edition 6.2002 → 10.2005 replaced by DIN V 105-100 and DIN EN 771-1
Bricks - Part 1: Solid bricks and vertically perforated bricks of the bulk density class equal to 1.2
DIN 105 - Part 1 Edition 8.1989 → 6.2002 replaced by DIN V 105-1
Masonry brick - solid brick and vertically perforated brick
DIN 105 - Part 1 · Edition 11.1982 → replaced by Edition 8.1989
Masonry bricks; Solid brick and vertically perforated brick
DIN V 105 - Part 2 Edition 6.2002 → 10.2005 replaced by DIN V 105-100 and DIN EN 771-1
Bricks - Part 1: Solid bricks and vertically perforated bricks of the bulk density class equal to 1.0
DIN 105 - Part 2 Edition 8.1989 → 6.2002 replaced by DIN V 105-2
Masonry bricks; Light vertical perforated brick
DIN 105 - Part 2 Edition 11.1982 → replaced by Edition 8.1989
Masonry bricks; Light perforated brick
DIN 105 - Part 2 · Edition 1.1972 → withdrawn
Masonry bricks; Lightweight brick
DIN 105 - Part 3 · Edition 5.1984 → 10.2005 replaced by DIN V 105-100 Edition 10.2005 and DIN EN 771-1 Edition 5.2005
Masonry bricks; High-strength bricks and high-strength clinker bricks
The standard contains information on high-strength bricks and high-strength clinker load-bearing and non-load-bearing masonry. These building materials are particularly suitable for creating highly stressed exterior and interior walls. The standard names requirements for testing and quality monitoring.
DIN 105 - Part 3 · Edition 7.1975 → replaced by Edition 5.1984
Masonry bricks; High-strength bricks and clinker
DIN 105 - Part 4 Edition 5.1984 → 10.2005 replaced by DIN V 105-100 Edition 10.2005, DIN EN 771-1 Edition 5.2005 and DIN EN 772-7 Edition 10.1998
Masonry bricks; Ceramic clinker
The standard contains information on ceramic clinker bricks for load-bearing and non-load-bearing masonry. Ceramic clinker bricks are mainly used for the construction of facades outdoors and indoors, as well as wherever a particular resistance to aggressive substances and mechanical surface loads is required. The standard names requirements and labeling.
DIN 105 - Part 4 · Edition 4.1974 → replaced by Edition 5.1984
Masonry bricks; Ceramic clinker
DIN 105 - Part 5 · Edition 6.2013 → current
Masonry bricks; Slightly elongated brick and light elongated brick panels
The standard applies to the use of light elongated bricks and light elongated brick panels of category 1 according to DIN EN 771-1, which are used for non-load-bearing internal partition walls made of masonry. It specifies the additional requirements for slightly elongated bricks that must be met by CE-marked masonry bricks according to DIN EN 771 Part 1 for use in non-load-bearing masonry according to DIN 4103 Part 1.
DIN 105 - Part 5 · Edition 5.1984 → replaced by Edition 6.2013
Masonry bricks; Slightly elongated brick and light elongated brick panels
The standard contains information on slightly elongated bricks for load-bearing and non-load-bearing masonry. Slightly elongated brick panels are intended for non-load-bearing walls. Slightly elongated bricks and light elongated brick panels are mainly used to produce interior walls. Requirements are mentioned.
DIN 105 - Part 6 Edition 6.2013 → current
Bricks · Plane bricks
The standard applies to masonry bricks of category I according to DIN EN 771-1, which are used for load-bearing and non-load-bearing masonry, mainly for creating external and internal walls. It defines additional requirements.
DIN V 105 - Part 6 Pre-standard Edition 6.2002 → replaced by DIN 105 - Part 6 Edition 6.2013
Masonry brick - plane brick
DIN 105 - Part 100 · Edition 1.2012 → current
Bricks - Bricks with special properties
The standard applies to masonry bricks of Category I according to DIN EN 771 Part 1 (but only for LD bricks: vertically perforated bricks, elongated perforated bricks; - HD bricks: solid bricks, vertically perforated bricks, facing bricks, facing bricks, vertically perforated bricks, solid clinkers, vertically perforated bricks, high-strength bricks and high-strength clinker bricks, ceramic clinker bricks, slotted bricks), which are used for load-bearing and non-load-bearing masonry, mainly for creating external and internal walls. It defines additional requirements.
DIN V 105 - Part 100 · Prestandard edition 10.2005 → replaced by DIN 105 Part 100 edition 1.2012
Bricks - Bricks with special properties
DIN 105 Edition 7.1969 → withdrawn
Masonry bricks; Solid brick and perforated brick
Pore-forming substances for brick production taken into account. Bricks 365 mm long and 300 mm wide were added. Provision on admissibility of grooves at the butt joints added. Brick bulk density 1.60 kg / dm 3 and 2.00 kg / dm 3 recorded. Color marking of the bricks changed. Editorially revised.
DIN 105 edition 3.1957 → withdrawn
Masonry bricks; Solid brick and perforated brick
DIN 105 edition 1.1952 → withdrawn
Masonry bricks; Solid brick and perforated brick
DIN 105 edition 10.1941 → withdrawn
Masonry brick (solid brick)
DIN 105 edition 12.1935 → withdrawn
Brick wall (???)
DIN 105 edition 8.1922 → withdrawn
Masonry bricks
DIN V 106 edition 10.2005 → current
Sand-lime bricks with special properties
The pre-standard specifies the requirements for sand-lime bricks that must also be met by CE-marked sand-lime bricks according to DIN EN 771-2 for direct use in masonry according to DIN 1053. (DIN V 106-1: 2003-02 and DIN V 106-2: 2003-02 could still be used until April 1, 2006)
DIN V 106 - Part 1 edition 2.2003 → 10.2005 replaced by DIN V 106 edition 10.2005 and DIN EN 771-2 edition 5.2005
Sand-lime bricks - Part 1: Solid, perforated, block, hollow block, flat bricks, flat elements, chamfer bricks, building panels, shaped bricks
The prestandard contained the required information on the shapes, dimensions, bulk density classes and compressive strength classes, including the designation and identification of sand-lime bricks as solid, perforated, block, hollow block, flat bricks, plan elements, bevel bricks and building boards as well as the specifications for the tests and the Proof of conformity for the requirements listed therein.
DIN V 106 - Part 2 edition 2.2003 → 10.2005 replaced by DIN V 106 edition 10.2005 and DIN EN 771-2 edition 5.2005
Sand-lime bricks - Part 2: facing bricks and facing bricks
The prestandard contained the necessary information about the shapes, dimensions, bulk density classes and compressive strength classes including the designation and identification of sand-lime bricks as facing bricks and facing bricks as well as the specifications for the tests and the proof of conformity for the requirements listed therein.
DIN 106 - Part 1 edition 9.1980 → replaced by DIN V 106-1 edition 2.2003
Sand-lime bricks - solid bricks, perforated bricks, block bricks, hollow blocks
DIN 106 - Part 2 edition 11.1980 → replaced by DIN V 106-2 edition 2.2003
Sand-lime bricks - facing bricks and facing bricks
DIN 106 edition 11.1972 → withdrawn
Sand-lime bricks; Solid stones, perforated stones and hollow blocks
DIN 106 · Edition 4.1969 → withdrawn
Sand-lime bricks; Solid stones, perforated stones and hollow blocks
DIN 106 - Part 1 · Edition 12.1962 → withdrawn
Sand-lime bricks; Solid stones, perforated stones and hollow blocks
DIN 106 - Part 1 · Edition 05.1955 → withdrawn
Sand-lime bricks; Solid, perforated and hollow blocks
DIN 106 edition 10.1952 → withdrawn
Sand-lime bricks (bricks)
DIN 106 edition 10.1941 → withdrawn
Sand-lime bricks (bricks)
DIN 106 edition 2.1936 → withdrawn
Sand-lime bricks (bricks)
DIN 106 edition 1.1927 → withdrawn
Sand-lime bricks (bricks)
DIN 107 · Edition 4.1974 → current
Designation with left or right in construction
DIN 107 edition 8.1939 → withdrawn
Left and right designation in construction
DIN 107 · Edition 5.1922 → withdrawn
Left and right designations for windows, doors, window and door hinges, stairs and cookers
DIN 108 - Part 1 · Edition 5.1988 → current
Slide projectors and slides · slides for general purposes and movie theater use; Nominal sizes, image limits, image position, labeling
The standard applies to the dimensions and design of slide frames and glass surrounds, the use of slides in movie theaters, requirements for slides for non-automatic and automatic presentation with a still projector, the image position and their identification.
DIN 108 - Part 1 · Edition 8.1979 → replaced by Edition 5.1988
Slide projectors and slides · slides for general purposes and movie theater use; Nominal sizes, image limits, image position, labeling
DIN 108 - Part 1 · Edition 12.1970 → withdrawn
Slide projection; General purpose and movie theater use slides; Nominal sizes, image limits, image position, labeling
DIN 108 - Part 1 · Edition 7.1959 → withdrawn
Slide projection; Glass pictures, picture tapes; Dimensions, image position and labeling
DIN 108 - Part 2 · Edition 4.1969 → withdrawn
Slide projection; Technical slides; Templates, execution, testing, presentation conditions
DIN 108 - Part 2 · Edition 7.1959 → withdrawn
Slide projection; Glass pictures, execution
DIN 108 - Part 3 · Edition 6.1972 → withdrawn
Slide projection; Holders for slides and picture tapes
DIN 108 - Part 4 Edition 10.1968 → withdrawn
Slide projection, slides, picture tapes; 5 × 5 slides for television purposes
DIN 108 - Part 5 · Edition 12.1970 → withdrawn
Slide projection picture tapes Dimensions of picture position
DIN 108 - Part 6 Edition 11.1984 → current
Slide projectors and slides · Outside diameter of the mount of slide and EPI projection lenses
The standard defines the dimensions for the outside diameter of the mount (outside diameter of the guide cylinder) of interchangeable projection lenses in still image projectors.
DIN 108 - Part 6 · Edition 6.1972 → replaced by Edition 11.1984
Slide projection; Outside diameter of the mount of slide projection lenses
DIN 108 - Part 7 · Edition 12.1988 → current
Slide projectors and slides · work projectors; Usable area, holding pins, projection area, evaluation
The standard specifies the connection dimensions, adjustment options and demonstration aids for the work projectors of versions A, B and C, which serve to ensure compatibility between the work projectors and the banners.
DIN 108 - Part 7 · Edition 5.1981 → replaced by Edition 12.1988
Slide projectors and slides · work projectors; Usable area, holding pins, projection area, evaluation
DIN 108 - Part 7 Supplement 1 Edition 7.1973 → current
Slide projection; Work projectors, DIN test transparency for minimum requirements with 9 DIN test fields, lines and fonts for practical use
DIN 108 - Part 7 Supplement 2 · Edition 12.1981 → current
Slide projectors and slides · work projectors; DIN setting transparency for viewing and projection conditions
DIN 108 - Part 8 Edition 3.1991 → current
Slide projectors and slides · straight magazine 5 × 5-36 and 5 × 5-50; Dimensions
The standard specifies the dimensions for a straight magazine for holding slides of nominal size 5 by 5 according to DIN 108 Part 1 in two sizes: for a capacity of 36 slides and 50 slides.
DIN 108 - Part 8 · Edition 12.1988 → replaced by Edition 3.1991
Slide projectors and slides · straight magazine 5 × 5-36 and 5 × 5-50; Dimensions
DIN 108 - part 8 edition 9.1988 → replaced by edition 12.1988
Slide projectors and slides · straight magazine 5 × 5-36 and 5 × 5-50; Dimensions
DIN 108 - Part 8 · Edition 8.1977 → replaced by Edition 9.1988
Slide projectors and slides · Straight magazine 5 × 5-36 and 5 × 5-50, dimensions
DIN 108 - Part 9 Edition 9.1988 → current
Slide projectors and slides · straight magazine 5 × 5-36 and 5 × 5-50; Teaching for magazine outline and toothing
The standard applies to a gauge for magazine outline and toothing, which is used to test straight magazines 5 × 5-36 and 5 × 5-50 according to DIN 108 Part 8.
DIN 108 - Part 9 · Edition 8.1977 → replaced by Edition 9.1988
Slide projectors and slides · Straight magazine 5 × 5-36 and 5 × 5-50, gauge for magazine outline and toothing
DIN 108 - Part 10 · Edition 10.1977 → current
Slide projectors and slides · Projection lenses for work projectors, optical parameters
DIN 108 - Part 17 · Edition 12.1988 → current
Slide projectors and slides · work projectors; Films, banners, demonstration aids
The standard specifies the connection dimensions for unmounted and mounted banners including all demonstration aids for work projectors of versions A, B and C according to DIN 108 Part 7, which serve to ensure compatibility between the work projectors and the banners.
DIN 108 - Part 17 · Edition 5.1981 → replaced by Edition 12.1988
Slide projectors and slides · work projectors; Films, banners, demonstration aids
DIN 108 - Part 20 · Edition 2.1996 → current
Slide projectors and slides · Evaluation of slide projectors; Evaluation program for the usability
The standard defines an evaluation program for the usability of slide projectors.
DIN 108 - Part 20 · Edition 11.1983 → replaced by Edition 2.1996
Slide projectors and slides · testing of slide projectors; Test program and test procedure
DIN 108 - Part 54 · Edition 5.1977 → replaced by DIN 108 Part 7 Edition 12.1988
Slide projectors and slides · Work projectors, locking cones, anti-glare devices, table heights
DIN 108 - Part 55 · Edition 3.1991 → current
Slide projectors and slides · straight magazine 5 × 5-36 and 5 × 5-50; Certification program
The standard specifies a procedure for type testing and approval of marks for straight magazines 5 × 5 - 36 and 5 × 5 - 50 in accordance with DIN 108 Part 8 and DIN 108 Part 9.
DIN 108 - Part 56 · Edition 6.1996 → current
Slide projectors and slides · slide mounts for slides for general purposes and for use in movie theaters; Certification program
The standard specifies a procedure for type testing and the issuing of the approval of marks for slide frames according to DIN 108-1.
DIN 108 edition 12.1938 → withdrawn
Glass pictures · Photo tapes for throwing pictures
DIN 108 edition 12.1929 → withdrawn
Slides · External dimensions, size of the usable image area, labeling strips
Glass pictures for throwing pictures
2nd edition of the standard
2nd edition of the standard
DIN 108 edition 1.1923 → replaced by edition 12.1929
Slides · External dimensions, size of the usable image area, labeling strips
1st edition of the standard
DIN 109 - Part 1 · Edition 12.1973 → current
Drive elements · Circumferential speeds
DIN 109 - Part 2 · Edition 12.1973 → current
Drive elements · Center distances for belt drives with V-belts
DIN 109 Edition 11.1955 → withdrawn
Relationships between load speeds according to DIN 112, belt pulley diameters according to DIN 111, DIN 2217 and peripheral speeds
DIN 109 · Edition 4.1923 → withdrawn
Relationships between load speeds, pulley diameters and peripheral speeds
DIN 110 edition 10.1922 → withdrawn
Pulleys, fastening on transmission shafts
DIN 111 edition 8.1982 → current
Drive elements · flat belt pulleys; Dimensions, nominal torques
DIN 111 edition 9.1972 → withdrawn
Drive elements; Flat belt pulleys; Dimensions and nominal torques
DIN 111 edition 12.1954 → withdrawn
Pulleys, main dimensions
DIN 111 edition 4.1923 → withdrawn
Pulleys for transmissions, construction sheet
DIN 112 edition 11.1955 → withdrawn
Load speeds
DIN 112 edition 10.1940 → withdrawn
Load speeds
DIN 112 edition 4.1923 → withdrawn
Load speeds of transmission shafts
DIN 113 · Edition 5.1924 → withdrawn
Lead screw pitches, metric
DIN 114 · Edition 7.1919 → withdrawn without replacement
Diameter for transmission shafts
DIN 115 - Part 1 · Edition 9.1973 → current
DIN 115 - Part 2 Edition 9.1973 → current
Drive elements · Clamp couplings, insert rings
DIN 115 edition 2.1922 → withdrawn
Clamp couplings for transmissions
DIN 116 edition 12.1971 → current
Drive elements; Disc couplings, dimensions, torques, speeds
DIN 116 edition 5.1954 → withdrawn
Disc couplings, main dimensions
DIN 116 edition 2.1922 → withdrawn
Disc couplings for transmissions
DIN 117 edition 9.1954 → withdrawn
Drive elements; Wall arms; for pillow block bearings according to DIN 118 main dimensions
DIN 117 edition 3.1924x → withdrawn
Wall arms for pedestal bearings for transmissions according to DIN 118
The cross edition of this 4th edition of the standard changes thread specifications to metric threads as well as some values for g and d 1
DIN 117 Edition 3.1924 → withdrawn
Wall arms for pedestal bearings for transmissions according to DIN 118
DIN 118 - Part 1 · Edition 7.1977 → current
Drive elements; Pedestal plain bearings for general mechanical engineering, main dimensions
DIN 118 - Part 1 · Edition 9.1954 → withdrawn
Pillow block bearings; with ring lubrication form L and K
DIN 118 - Part 2 · Edition 9.1954 → withdrawn
Pillow block bearings; with ring lubrication type G
DIN 118 edition 9.1943 → withdrawn
Pillow block bearings for transmissions
DIN 118 edition 9.1924 → withdrawn
Pillow block bearings for transmissions
DIN 119 · Edition 12.1955 → withdrawn
Hangers, connection dimensions
DIN 119 · Edition 12.1924 → withdrawn
Hangers for transmissions
DIN 120 - Part 1 edition 11.1936 → replaced by DIN 4132 edition 2.1981
Calculation bases for steel components of cranes and crane runways
DIN 120 - Part 2 edition 11.1936 → replaced by DIN 4132 edition 2.1981
Calculation bases for steel components of cranes and crane runways · Principles for structural design
DIN 120 - Supplement · Edition 11.1944 → replaced by DIN 4132 Edition 2.1980
Calculation bases for steel components of cranes and crane runways · Explanations
DIN 121 edition 3.1920 → 10.1968 withdrawn without replacement
Grooves for hemp rope sheaves for transmissions
DIN 122 edition 4.1924 → withdrawn
Disk springs for machine tools, application sheet
DIN 123 - Part 1 · Edition 6.1956 → withdrawn
Half-round rivets; for boiler construction from 10 to 36 mm in diameter
DIN 123 - Part 1 · Edition 7.1948 → withdrawn
Half-round rivets for boiler construction; 10 to 36 mm in diameter
With this 2nd edition of the standard, rivets were changed to metric diameters.
DIN 123 - Part 1 · Edition 9.1921 → withdrawn
Half-round rivets for boiler construction; from 10 to 43 mm in diameter
DIN 123 - Part 2 · Edition 2.1952 → withdrawn
Half-round rivets for boiler construction; The rivet length depends on the clamping length. The setting head is a round head, the shooting head is a round head
DIN 123 - Part 2 · Edition 10.1923 → withdrawn
Half-round rivets for boiler construction; Rivet lengths depending on the grip lengths, construction sheet
DIN 123 - Part 3 Supplement 1 Edition 7.1952 → withdrawn
Button head rivets for locomotive construction, 10 to 36 mm diameter, setting head: button head, locking head: half countersunk head
DIN 123 - Part 3 · Edition 2.1952 → withdrawn
Half-round rivets for boiler construction; The rivet length depends on the clamping length. The setting head is a button head
DIN 123 - Part 3 · Edition 10.1923 → withdrawn
Half-round rivets for boiler construction; Rivet lengths depending on the grip lengths, construction sheet
DIN 123 - Part 4 Edition 10.1923 → withdrawn
Half-round rivets for boiler construction; Rivet lengths depending on the grip lengths, construction sheet
DIN 123 - Part 5 Edition 10.1923 → withdrawn
Half-round rivets for boiler construction; Rivet lengths depending on the grip lengths, construction sheet
DIN 124 · Edition 3.2011 → current
Half-round rivets - nominal diameter 10 to 36 mm
The standard contains the dimensional specifications and technical delivery conditions for half-round rivets and specifies their designation.
DIN 124 edition 5.1993 → replaced by edition 3.2011
Half-round rivets; Nominal diameter 10 to 36 mm
DIN 124 edition 7.1977 → replaced by edition 5.1993
Half-round rivets, nominal diameter 10 to 36 mm
DIN 124 - Part 1 · Edition 6.1956 → withdrawn
Half-round rivets; for steel construction from 10 to 36 mm in diameter
DIN 124 - Part 1 · Edition 7.1948 → withdrawn
Half-round rivets for steel construction; 10 to 36 mm in diameter
With this 2nd edition of the standard, the rivets were converted to metric diameters.
DIN 124 - Part 1 · Edition 9.1921 → withdrawn
Half-round rivets for iron construction; from 10 to 43 mm in diameter
DIN 124 - Part 2 · Edition 2.1952 → withdrawn
Half-round rivets for steel construction; Rivet lengths depending on the clamping lengths Setting head: Round head Shooting head: Round head
DIN 124 - Part 2 · Edition 10.1923 → withdrawn
Half-round rivets for iron construction; Rivet lengths depending on the grip lengths, construction sheet
DIN 124 - Part 3 · Edition 2.1952 → withdrawn
Half-round rivets for steel construction; The rivet length depends on the clamping length. The setting head is a round head, the shooting head is a countersunk head
DIN 124 - Part 3 · Edition 10.1923 → withdrawn
Half-round rivets for iron construction; Rivet lengths depending on the grip lengths, construction sheet
DIN 124 - Part 4 Edition 10.1923 → withdrawn
Half-round rivets for iron construction; Rivet lengths depending on the grip lengths, construction sheet
DIN 125 - Part 1 Edition 3.1990 → 11.2000 replaced by DIN EN ISO 7089 and DIN EN ISO 7090
Washers, product class A, up to hardness 250 HV, preferably for hexagon bolts and nuts
DIN 125 - Part 2 Edition 3.1990 → 11.2000 replaced by DIN EN ISO 7089 and DIN EN ISO 7090
Washers, product class A, from hardness 300 HV, preferably for hexagon bolts and nuts
DIN 125 · Edition 5.1968 → withdrawn
Discs; Medium version (previously blank), preferably for hexagon bolts and nuts
DIN 125 · Edition 5.1943 → withdrawn
Washers for hexagon bolts and nuts
DIN 125 - Part 1 Issue 3.1923 → withdrawn
Bare washers for hexagon bolts and nuts
DIN 125 - Part 2 · Edition 3.1923 → withdrawn
Bare washers for hexagon bolts and nuts
DIN 126 Edition 3.1990 → 11.2000 replaced by DIN EN ISO 7091
Washers, product class C, preferably for hexagon bolts and nuts
DIN 126 edition 5.1968
Discs; Coarse version (previously raw), preferably for hexagon bolts and nuts
DIN 126 · Edition 5.1943 → withdrawn
Washers for hexagon bolts and nuts, raw
DIN 126 · Edition 4.1927 → withdrawn
Raw slices
DIN 126 - Part 1 · Edition 3.1923 → withdrawn
Raw slices
DIN 127 edition 10.1987 → 7.1993 withdrawn without replacement
Spring washers, bent or smooth with a rectangular cross-section
DIN 127 · Edition 12.1970 → withdrawn
Spring washers; curved or smooth with a rectangular cross-section
DIN 127 · Edition 1.1961 → withdrawn
Spring washers
DIN 127 · Edition 4.1943 → withdrawn
Spring washers
DIN 127 · Edition 7.1929 → withdrawn
Spring washers
3rd edition of the standard
DIN 127 · Edition 7.1923 → withdrawn
Spring washers with a rectangular cross-section
DIN 128 edition 10.1994 → 5.2003 withdrawn without replacement
Spring washers, arched
The standard contains the dimensional specifications and technical delivery conditions for spring washers, curved and specifies their designation.
DIN 128 · Edition 4.1968 → withdrawn
Spring washers; curved or wavy (high tension spring washers)
DIN 128 edition 7.1923 → 8.1929 withdrawn without replacement
Spring washers with a square cross-section
DIN 129 · Edition 5.1923 → withdrawn
Single wrench
DIN 130 Edition 3.1924 → withdrawn
Double wrenches with unequal jaw widths
DIN 131 · Edition 5.1923 → withdrawn
Double wrenches with the same mouth width
DIN 133 Edition 7.2009 → current
Screwdriving tools - open-end wrenches - dimensions and design
DIN 133 edition 11.1982 → replaced by edition 7.2009
Open-end wrench
DIN 133 edition 3.1971 → replaced by edition 11.1982
Open-end wrench
DIN 133 · Edition 5.1924 → withdrawn
Bump key
DIN 134 edition 3.1923 → withdrawn
Semi-bright washers for hexagon bolts and nuts
DIN 135 Edition 7.1943 → withdrawn
Metal circular saw blades for slotting
DIN 135 edition 11.1924 → withdrawn
Slotting cutter, guidelines for the number of teeth
DIN 136 edition 11.1924 → withdrawn
Metal circular saws, guidelines for the number of teeth
DIN 137 · Edition 5.1994 → 5.2003 withdrawn without replacement
Spring washers, waved
The standard contains the dimensional specifications and technical delivery conditions for spring washers, corrugated and specifies their designation.
DIN 137 · Edition 12.1970 → withdrawn
Spring washers; domed or wavy
DIN 137 · Edition 7.1953 → withdrawn
Spring washers
DIN 137 · Edition 12.1943 → withdrawn
Spring washers
DIN 138 · Edition 4.2003 → current
Machine tools for metal - bores, grooves and drivers for tools with cylindrical bores and tapered bores 1:30
The standard specifies the dimensions of bores, grooves and drivers for tools with a cylindrical bore and a tapered bore with a 1:30 taper.
DIN 138 edition 9.1955 → replaced by edition 4.2003
Machine tools for metal; Bores, grooves and drivers for tools with cylindrical bores and tapered bores with taper 1: 30
DIN 138 edition 11.1943 → withdrawn
Bores, grooves and drivers for milling cutters, reamers and countersinks
DIN 138 · Edition 5.1924 → withdrawn
Bores, grooves and drivers for milling cutters, reamers and countersinks
DIN 139 · Edition 10.1921 → withdrawn
Symbols for rivets and screws in iron structures
DIN 140 - Part 1 Edition 10.1931 → 12.1993 replaced by DIN ISO 1302
Drawings; Surfaces; nature
DIN 140 - Part 1 · Edition 2.1921 → withdrawn
Drawings, surface marks
DIN 140 - Part 2 Edition 10.1931x → withdrawn
Drawings; Surface signs
DIN 140 - Part 2 · Edition 12.1922 → withdrawn
Drawings, surface marks
DIN 140 - Part 3 Edition 10.1931 → 12.1993 replaced by DIN ISO 1302
Drawings; Surfaces; Word indications
DIN 140 - Part 4 Edition 10.1931x → 12.1993 replaced by DIN ISO 1302
Surfaces; Graphic entry of the surface signs
DIN 140 - Part 5 Edition 10.1931 → withdrawn
Drawings; Surfaces; Identification examples
2nd edition of the standard.
DIN 140 - Part 6 Edition 10.1931 → withdrawn
Drawings; Surfaces; Identification examples
2nd edition of the standard.
DIN 140 - Part 7 Edition 5.1966 → 12.1993 replaced by DIN ISO 1302
Drawings; Surfaces for ceramic workpieces; Quality, surface symbols, word information, examples of labeling
DIN 141 edition 8.1922 → withdrawn
Driving wedges, insertion wedges, nose wedges, application sheet
DIN 142 edition 8.1922 → withdrawn
Flat wedges, flat nose wedges, application sheet
DIN 143 edition 8.1922x → withdrawn
Hollow wedges, nasal hollow wedges, application sheet
Addition 2.1951: Not for new designs
DIN 143 edition 8.1922 → withdrawn
Hollow wedges, nasal hollow wedges, application sheet
DIN 144 · Edition 4.1924 → withdrawn
Parallel keys, sliding springs for machine tools, application sheet
DIN 145 Edition 10.1925 → withdrawn
Bores for retaining and jacking screws for sliding springs according to DIN 496
DIN 146 edition 8.1932 → withdrawn
Bearing bushes, thin-walled
DIN 146 · Edition 1.1921 → withdrawn
Bearing bushes, thin-walled
DIN 147 edition 8.1932 → withdrawn
Bearing bushes, thick-walled
DIN 147 edition 1.1921 → withdrawn
Bearing bushes, thick-walled
DIN 148 · Edition 2.1921 → withdrawn
Finishing bore sB, standard bore
DIN 149 edition 2.1921 → withdrawn
Wide finish fit sWL, finish fit, standard bore
DIN 150 edition 5.1923 → withdrawn
Finish fit sL, finish fit, standard bore
DIN 151 · Edition 2.1921 → withdrawn
Plain sliding seat sG, plain fit, standard bore
DIN 152 edition 1.1928 → withdrawn
Clearances and oversizes, unit bore
DIN 152 Edition 7.1925 → withdrawn
Clearances and oversizes, unit bore
DIN 153 edition 1.1928 → withdrawn
Games and excesses, unity wave
DIN 153 edition 7.1925 → withdrawn
Games and excesses, unity wave
DIN 154 edition 2.1921 → withdrawn
Straight shaft sW, standard shaft
DIN 155 edition 2.1921 → withdrawn
Next finish fit sWL, finish fit, standard shaft
DIN 156 edition 5.1923 → withdrawn
Smooth running fit sL, smooth fit, standard shaft
DIN 157 edition 2.1921 → withdrawn
Plain sliding seat sG, plain fit, standard shaft
DIN 158 - Part 1 · Edition 6.1997 → current
Metric tapered external thread with associated cylindrical internal thread · Nominal dimensions, limit dimensions, limit dimensions and testing
The standard specifies the nominal, limit and limit dimensions as well as their testing for the metric tapered external thread and the cylindrical internal thread.
DIN 158 - Part 2 · Edition 6.1997 → current
Metric tapered external thread with associated cylindrical internal thread · Gauge system, application of gauges, calculation of gauge dimensions and construction features
The standard defines the gauge system for threads according to DIN 158 - Part 1.
DIN 158 Edition 8.1986 → replaced by DIN 158 - Part 1 Edition 6.1997
Metric tapered external thread with associated cylindrical internal thread · Nominal dimensions, limit dimensions, limit dimensions
The standard specifies the nominal, limit and limit dimensions as well as their testing for the metric tapered external thread and the cylindrical internal thread.
DIN 158 · Edition 4.1971 → replaced by Edition 8.1986
Metric tapered external thread with associated cylindrical internal thread · Nominal dimensions and permissible deviations
DIN 158 - Part 1 · Edition 6.1954 → withdrawn
Metric tapered thread, taper 1:16, theoretical values
DIN 159 edition 4.1923 → withdrawn
Coarse bore gB, standard bore
DIN 160 edition 4.1923 → withdrawn
Coarse fit g 4 Coarse fit, unit bore
DIN 161 Edition 4.1923 → withdrawn
Coarse fit g 3 Coarse fit, unit bore
DIN 162 edition 3.1924 → withdrawn
Coarse fit g 2 coarse fit, unit bore
DIN 163 · Edition 4.1923 → withdrawn
Coarse fit g 1 coarse fit, unit bore
DIN 164 edition 4.1923 → withdrawn
Coarse wave gW, standard wave
DIN 165 · Edition 4.1923 → withdrawn
Coarse fit g 4, coarse fit, standard shaft
DIN 166 Edition 4.1923 → withdrawn
Coarse fit g 3, coarse fit, standard shaft
DIN 167 · Edition 3.1924 → withdrawn
Coarse fit g 2, coarse fit, standard shaft
DIN 168 - Part 1 · Edition 4.1998 → current
Round thread · Thread dimensions for glass containers
The threads specified in this standard apply primarily to packaging made of glass.
DIN 168 - Part 1 · Edition 12.1979 → replaced by Edition 4.1998
Round thread, preferably for glass containers; Thread dimensions
DIN 168 - Part 1 · Edition 3.1951 → withdrawn
Round thread for parts made of glass and associated screw connections
DIN 168 edition 4.1923 → replaced by DIN 2057 edition 1.1928
Manufacturing accuracy of the working gauges
DIN 169 · Edition 4.1923 → withdrawn
Coarse fit g 1, coarse fit, standard shaft
DIN 170 · Edition 6.1955 → withdrawn
Big games
DIN 170 edition 1.1928 → withdrawn
Big games
Rough fit
DIN 170 edition 7.1923 → withdrawn
Big games
Rough fit
DIN 171 edition 7.1923 → withdrawn
Manufacturing accuracy of the test gauges for shaft work gauges
DIN 172 edition 11.1992 → 4.2006 withdrawn without replacement
Collar drill bushes
Collar drill bushes according to this standard can only be combined with push-in drill bushes according to DIN 173 Part 1.
DIN 172 Edition 11.1971 → withdrawn
Collar drill bushes
DIN 172 · Edition 1.1953 → withdrawn
Collar drill bushes
DIN 172 · Edition 7.1936 → withdrawn
Collar drill bushes
DIN 172 Edition 7.1923 → withdrawn
Manufacturing accuracy of the test gauges for bore work gauges
DIN 173 - Part 1 edition 11.1992 → 4.2006 withdrawn without replacement
Push-in drill bushes; Quick-change bushes form K and KL; Replacement bushes form L; equipment
Push-in drill bushes according to this standard can only be combined with collar drill bushes according to DIN 172 and with drill bushes according to DIN 179.
DIN 173 - Part 2 edition 11.1992 → 11.1996 withdrawn without replacement
Push-in drill bushes, interchangeable bushes form E, quick-change bushes form ES, base bushes, cylinder screws with shoulder
DIN 173 - Part 1 edition 11.1971 → withdrawn
Push-in drill bushes; Quick-change bushes form A and collar screws
DIN 173 - Part 2 · Edition 1.1968 → withdrawn
Push-in drill bushes; Interchangeable sockets, quick-change sockets form ES and ER Basic sockets, socket head cap screws with shoulder
DIN 173 · Edition 5.1955 → withdrawn
Drill bushings, sockets and collar screws
DIN 173 · Edition 7.1951 → withdrawn
Drill bushes; Sockets and collar screws
Forms B, C and D deleted, dimension l 1 enlarged, permissible center deviation added, shoulder screw replaced by collar screw with a larger nominal thread diameter.
DIN 173 · Edition 7.1936 → withdrawn
Insert drill bushes and shoulder screws
DIN 174 edition 6.1969 → replaced by DIN EN 10278 edition 12.1999
Bright flat steel, dimensions, permissible deviations, weights
DIN 174 · Edition 5.1959 → withdrawn
Bright, sharp-edged flat steel; Dimensions, permissible deviations, weights
DIN 174 edition 3.1943 → withdrawn
Flat steel, drawn, ISA tolerance field h 11, h 12, h 14
DIN 174 · Edition 1.1928 → withdrawn
Flat steel, drawn, -10 units according to DIN 773
DIN 175 edition 10.1981 → replaced by DIN EN 10278 edition 12.1999
Polished round steel; Dimensions, permissible deviations according to ISO tolerance field h9
DIN 175 · Edition 5.1959 → withdrawn
Polished round steel; ISA tolerance field h9
DIN 175 edition 2.1943 → withdrawn
Round steel, polished, ISA tolerance field h 9 (h 8)
DIN 175 Edition 10.1923 → withdrawn
Precision round steel, bright drawn and polished (formerly silver steel and stub steel), -3 fitting units according to DIN 773
DIN 176 edition 2.1972 → replaced by DIN EN 10278 edition 12.1999
Bright hexagonal steel, dimensions, permissible deviations, weights
DIN 176 · Edition 5.1959 → withdrawn
Bright hexagonal steel; Dimensions, permissible deviations, weights
DIN 176 edition 9.1939 → withdrawn
Hexagonal steel, drawn, ISA tolerance field h 11
DIN 176 Edition 4.1925 → withdrawn
Hexagonal steel, bright drawn, accuracy -10 units according to DIN 773
DIN 177 edition 11.1988 → 9.1996 replaced by DIN EN 10218-2 edition 8.1996
Round steel wire, cold drawn, dimensions, tolerances, weights
DIN 177 · Edition 3.1971 → withdrawn
Cold drawn steel wire; Dimensions, permissible deviations, weights
DIN 177 edition 9.1934 → withdrawn
Steel wire, drawn
DIN 177 · Edition 10.1927 → withdrawn
Drawn steel wire (iron wire) (formerly German millimeter wire gauge)
DIN 177 · Edition 10.1923 → withdrawn
Steel wire (iron wire), drawn (formerly German millimeter wire gauge)
DIN 178 edition 6.1969 → replaced by DIN EN 10278 edition 12.1999
Bright square steel, dimensions, permissible deviations, weights
DIN 178 · Edition 5.1959 → withdrawn
Bright square steel; Dimensions, permissible deviations, weights
DIN 178 edition 9.1947 → withdrawn
Square steel, drawn, ISA tolerance field h 11
3rd edition: Old permissible deviations deleted. Name and notes added.
DIN 178 · Edition 4.1926 → withdrawn
Square steel, bright drawn, -10 units according to DIN 773
DIN 179 edition 11.1992 → 4.2006 withdrawn without replacement
Drill bushes
Drill bushes according to this standard can only be combined with push-in drill bushes according to DIN 173 Part 1.
DIN 179 Edition 11.1971 → withdrawn
Drill bushes
DIN 179 · Edition 1.1953 → withdrawn
Drill bushes
DIN 179 Edition 7.1936 → withdrawn
Cylindrical drill bushes
DIN 179 edition 1.1925 → withdrawn
Cylindrical drill bushes
DIN 180 Edition 7.1936 → withdrawn
Conical drill bushes
DIN 180 edition 1.1925 → withdrawn
Conical drill bushes
DIN 181 edition 12.1920 → withdrawn
Grinding wheels for back-turned and pointed cutters
DIN 182 edition 12.1920 → withdrawn
Grinding wheels for milling cutters and reamers
DIN 183 · Edition 12.1920 → withdrawn
Grinding wheels for jigs and gauges
DIN 184 edition 12.1920 → withdrawn
Grinding wheels for twist drills
DIN 185 edition 12.1920 → withdrawn
Grinding wheels for turning tools and woodworking cutters
DIN 186 Edition 9.2010 → current
T-head bolts with square
The standard contains the dimensional specifications and technical delivery conditions for T-head bolts with square head and specifies their designation.
DIN 186 edition 9.2007 → replaced by edition 9.2010
T-head bolts with square
DIN 186 edition 4.1988 → replaced by edition 9.2007
T-head bolts with square
DIN 186 edition 1.1987 → replaced by edition 4.1988
T-head bolts with square
DIN 186 edition 11.1970 → replaced by edition 1.1987
T-head bolts with square
DIN 186 - Part 1 · Edition 1.1942 → withdrawn
T-head bolts; with square, M 6 to M 48
DIN 186 - Part 2 Edition 10.1937x → withdrawn
T-head bolts; with square, 1/2 "to 2"
DIN 186 edition 2.1930 → withdrawn
T-head bolts with square
DIN 187 edition 2.1922 → withdrawn
Angle arms
to pillow block bearings for transmissions according to DIN 118
DIN 188 · Edition 2.2011 → current
T-head bolts with nose
The standard contains the dimensional specifications and technical delivery conditions for T-head bolts with nose and thread for fastening components with the help of T-slots, on foundations or other structures, and specifies their designation.
DIN 188 edition 9.2010 → replaced by edition 2.2011
T-head bolts with nose
DIN 188 edition 9.2007 → replaced by edition 9.2010
T-head bolts with nose
DIN 188 edition 1.1987 → replaced by edition 9.2007
T-head bolts with nose
DIN 188 · Edition 1.1971 → withdrawn
T-head bolts; with nose
DIN 188 - Part 1 · Edition 1.1942 → withdrawn
T-head bolts; with nose, M 10 to M 80
DIN 188 - Part 2 · Edition 10.1937x → withdrawn
T-head bolts; with nose, 1/2 "to 2 1/2", W 72 × 1/4 "and W 80 × 1/4"
DIN 188 · Edition 4.1927 → withdrawn
T-head bolts with lugs
DIN 189 · Edition 7.1977 → current
Drive elements; Sole plates, main dimensions
DIN 189 · Edition 11.1955 → withdrawn
Drive elements; Soleplates; for pillow block bearings according to DIN 118 main dimensions
DIN 189 - Part 1 · Edition 2.1922 → withdrawn
Base plates for pedestal bearings for transmissions according to DIN 118
DIN 189 - Part 2 · Edition 2.1922 → withdrawn
Base plates for pedestal bearings for transmissions according to DIN 118
DIN 190 Edition 2.1936 → 7.1986 replaced by DIN 69147-1 and DIN 69864
Tapered (conical) grinding wheels; Guidelines for Slope (Slope) and Side Jaw Tools
DIN 191 edition 12.1954 → 8.1985 withdrawn without replacement
Drive elements; Double anchor plates; For hammer screws according to DIN 261 part 1 for base plates according to DIN 189 and machines
DIN 191 edition 4.1943 → withdrawn
Double anchor plates for T-head bolts
DIN 191 edition 2.1930 → withdrawn
Double anchor plates for T-head bolts to base plates according to DIN 189 Part 2
DIN 191 Edition 6.1923 → withdrawn
Double anchor plates for T-head bolts to base plates according to DIN 189 Part 2
DIN 192 Edition 12.1954 → withdrawn without replacement
Drive elements; Double wall anchor plates; for hammer screws according to DIN 261 part 1 for wall brackets according to DIN 117
DIN 192 edition 4.1943x → withdrawn
Double wall anchor plates for hammer screws
DIN 192 Edition 6.1923 → withdrawn
Double wall anchor plates for wall arms according to DIN 117
DIN 193 edition 2.1922 → withdrawn
Wall box for pedestal bearings for transmissions according to DIN 118
DIN 194 edition 2.1945 → withdrawn
Suspension brackets for pedestal bearings for transmissions according to DIN 118
DIN 194 edition 2.1922 → withdrawn
Suspension brackets for pedestal bearings for transmissions according to DIN 118
DIN 195 - Part 1 · Edition 2.1922 → withdrawn
Stand blocks for pedestal bearings for transmissions according to DIN 118
DIN 195 - Part 2 · Edition 2.1922 → withdrawn
Stand blocks for pedestal bearings for transmissions according to DIN 118
DIN 198 edition 12.1976 → 1.2008 withdrawn without replacement
Final paper formats according to DIN 476; Examples of the application of the A series
DIN 198 edition 9.1936 → withdrawn
Paper formats according to DIN 476; A-series applications
DIN 198 · Edition 10.1923 → withdrawn
Paper formats according to DIN 476, A-series applications
DIN 199 - Part 1 · Edition 3.2002 → withdrawn
Technical product documentation - CAD models, drawings, and parts lists · Terms
The standard specifies terms and definitions for models, drawings and parts lists as they are used for technical product documentation in the field of mechanical technology. It does not define a system, but is to be understood as a lexicon for selected terms and document types.
After the standard has been withdrawn, it is recommended to use DIN EN ISO 10209.
After the standard has been withdrawn, it is recommended to use DIN EN ISO 10209.
DIN 199 - Part 1 · Edition 5.1984 → replaced by Edition 3.2002
Terms in drawing and parts lists; drawings
DIN 199 - part 2 edition 12.1977 → replaced by DIN 199 part 1 edition 3.2002
Terms in drawing and parts lists; Parts lists
DIN 199 - Part 3 Edition 8.1978 → 12.2008 withdrawn without replacement
Terms in drawing and parts lists; BOM processing, terms in key systems
DIN 199 - Part 4 Edition 10.1981 → withdrawn
Terms in drawing and parts lists; Changes
After the standard has been withdrawn, it is recommended to use DIN EN ISO 10209.
DIN 199 - Part 5 Edition 10.1981 → withdrawn
Terms in drawing and parts lists; BOM processing, BOM explosion
After the standard has been withdrawn, it is recommended to use DIN EN ISO 10209.
DIN 199 Edition 9.1962 → 5.1984 replaced by DIN 199 Part 1
Technical drawings; Designations
DIN 199 · Edition 10.1923 → withdrawn
Drawing types
DIN 200 - Part 1 · Edition 3.1924 → withdrawn
Drawings, processing and treatment information, word information
DIN 200 - Part 2 · Edition 4.1924 → withdrawn
Drawings, processing and treatment details, examples
DIN 201 edition 5.1990 → 5.2002 replaced by DIN ISO 128-50
Technical drawings, hatching, representation of cut surfaces and materials
DIN 201 edition 2.1953 → replaced by edition 5.1990
Drawings; Hatching and colors to identify materials
DIN 201 edition 10.1926 → withdrawn
Drawings; Hatching and colors to identify materials
DIN 202 edition 11.1999 → current
Thread overview
For quick information, the standard contains the threads used generally or for a larger special area. Table 1 contains threads according to DIN standards. In table 2 threads according to ISO standards are compiled. Frequently occurring threads according to foreign standards are summarized in Table 3.
DIN 202 edition 1.1988 → replaced by edition 11.1999
Thread; Overview
DIN 202 edition 12.1981 → replaced by edition 1.1988
Thread; Overview
DIN 202 edition 6.1938x → withdrawn
Thread; Abbreviated names
DIN 202 edition 4.1926 → withdrawn
Thread, abbreviated designations
DIN 202 edition 1.1924 → withdrawn
Thread, abbreviated designations
DIN 203 edition 4.1925 → withdrawn
Thread with the profiles of the Whitworth and the metric thread, overview
DIN 204 edition 12.1996 → current
Hand taper reamers for Morse taper
Reamers according to this standard are used to finish reaming holes with a Morse taper, e.g. B. conical sleeves according to DIN 228-2 determined.
DIN 204 edition 5.1975 → replaced by edition 12.1996
Hand taper reamers for Morse taper
DIN 204 edition 3.1960 → withdrawn
Conical reamers with straight shank; for morse taper
DIN 204 · Edition 6.1947 → withdrawn
Taper reamers, with straight shank for Morse taper
DIN 204 edition 7.1922 → withdrawn
Taper reamers for Morse taper
DIN 205 edition 12.1996 → current
Hand taper reamers for metric taper
Reamers according to this standard are intended for finishing tapered bores with a 1:20 taper, e.g. B. for metric taper sleeves according to DIN 228-2.
DIN 205 · Edition 5.1975 → replaced by Edition 12.1996
Hand taper reamers for metric taper
DIN 205 Edition 7.1922 → withdrawn
Conical reamers, for metric cones
DIN 206 · Edition 03.2008 → current
Hand reamers
The standard specifies the dimensions for hand reamers with a straight shank.
DIN 206 edition 12.2007 → replaced by edition 03.2008
Hand reamers
The standard specifies the dimensions for hand reamers with a straight shank.
DIN 206 edition 12.1996 → replaced by edition 12.2007
Hand reamers
The dimensions specified in this standard apply to hand reamers.
DIN 206 edition 9.1979 → replaced by edition 12.1996
Hand reamers
DIN 206 edition 9.1973 → withdrawn
Hand reamers
DIN 206 edition 11.1922 → withdrawn
Hand reamers; unadjustable
DIN 207 · Edition 1.1924 → withdrawn
Hand reamers, adjustable
DIN 208 · Edition 10.1981 → current
Machine reamers with morse taper shank
DIN 208 · Edition 9.1962 → withdrawn
Machine reamers with Morse taper
DIN 208 · Edition 4.1942 → withdrawn
Machine reamers with Morse taper, non-adjustable
DIN 208 edition 11.1922 → withdrawn
Machine reamers with Morse taper, non-adjustable
DIN 209 edition 8.1979 → withdrawn
Machine reamers with screwed-on knives
DIN 209 edition 11.1976 → replaced by edition 8.1979
Machine reamers with screwed-on knives
DIN 209 edition 9.1962 → withdrawn
Machine reamers with morse taper and screwed-on knives
DIN 209 edition 11.1922 → withdrawn
Machine reamers with morse taper and screwed-on knives
DIN 210 · Edition 1.1924x → withdrawn without replacement
Machine tools for metal; Machine reamers with morse taper; adjustable
DIN 210 · Edition 1.1924 → withdrawn
Machine reamers with Morse taper and screwed-on knives, adjustable
DIN 211 · Edition 1.1924 → withdrawn without replacement
Basic reamers with Morse taper, adjustable
DIN 212 - Part 1 Edition 9.1979 → current
Machine reamers with straight shank · continuous shank
DIN 212 - Part 2 · Edition 2.2011 → current
Machine reamers with straight shank · stepped shank
DIN 212 - Part 2 · Edition 10.1981 → replaced by Edition 2.2011
Machine reamers with straight shank · stepped shank
DIN 212 - Part 3 · Edition 2.2011 → current
Machine reamers with straight shank · NC reamers, dimensions
DIN 212 edition 9.1962 → withdrawn
Machine reamers with straight shank
DIN 212 · Edition 4.1942 → withdrawn
Machine reamers with straight shank, non-adjustable
DIN 212 edition 11.1922 → withdrawn
Machine reamers with straight shank, non-adjustable
DIN 213 edition 4.1942 → withdrawn
Machine reamers with square, non-adjustable
DIN 213 edition 11.1922 → withdrawn
Machine reamers with square, non-adjustable
DIN 214 edition 11.1922 → withdrawn
Machine reamers with square and screwed-on knives
DIN 215 · Edition 1.1924 → withdrawn
Machine reamers with square, adjustable
DIN 216 · Edition 1.1924 → withdrawn
Basic reamers with square, adjustable
DIN 217 edition 9.1972 → 8.2005 withdrawn without replacement
Clip-on holder with Morse taper for clip-on reamers and shell-on drills
DIN 217 edition 11.1942 → withdrawn
Attachment holder, with Morse taper, for reamers and countersinks
DIN 217 edition 1.1923 → withdrawn
Attachment holder with Morse taper for reamers and countersinks
DIN 218 edition 11.1944 → withdrawn
Clip-on holder, with square, for reamers and countersinks
DIN 218 edition 1.1923 → withdrawn
Clip-on holder with square for reamers and countersinks
DIN 219 edition 10.1981 → current
Attachable reamers
DIN 219 edition 8.1971 → withdrawn
Reamers; made of high speed steel
DIN 219 edition 4.1942 → withdrawn
Attachable reamers, non-adjustable
DIN 219 edition 1.1923 → withdrawn
Attachable reamers, non-adjustable, construction sheet
DIN 220 · Edition 9.1979 → withdrawn
Slip-on reamers with screwed-on knives
DIN 220 · Edition 11.1976 → replaced by Edition 9.1979
Slip-on reamers with screwed-on knives
DIN 220 · Edition 9.1962 → withdrawn
Slip-on reamers with screwed-on knives
DIN 220 · Edition 7.1928 → withdrawn
Slip-on reamers with screwed-on knives
DIN 221 edition 1.1923 → withdrawn without replacement
Plug-on basic reamers; adjustable construction sheet
DIN 222 · Edition 10.1981 → current
Arbor borer
DIN 222 · Edition 8.1971 → withdrawn
Mounted borer (countersink); made of high speed steel
DIN 222 · Edition 1.1923 → withdrawn
Attachable countersink
DIN 223 - Part 1 Edition 9.1979 → 6.1990 replaced by DIN EN 22568
Round dies for metric ISO standard threads M 1 to M 68
DIN 223 - Part 1 · Edition 9.1971 → replaced by Edition 9.1979
Round dies; For metric ISO standard threads and fine threads from M 1 to M 68
DIN 223 - Part 3 Edition 9.1979 → 6.1990 replaced by DIN EN 22568
Round dies for metric ISO fine threads M 1 to M 68
DIN 223 - Part 1 Edition 12.1943 → withdrawn
Round dies for metric threads and metric fine threads, thread diameter 1 to 68 mm
DIN 223 - Part 2 Edition 12.1943 → withdrawn
Round dies; for Whitworth thread
DIN 223 Edition 7.1925 → withdrawn
Round slotted dies
DIN 224 edition 12.1943 → withdrawn
Die capsules
DIN 224 Edition 7.1925 → withdrawn
Die capsules
DIN 225 edition 12.1987 → replaced by DIN EN 22568 edition 6.1990
Die holder
DIN 225 edition 1.1979 → replaced by edition 12.1987
Die holder
DIN 225 edition 10.1967 → replaced by edition 1.1979
Die holders; for dies according to DIN 223
DIN 225 Edition 7.1925 → withdrawn
Die holder for round slotted dies with capsule
DIN 226 Edition 7.1928 → withdrawn
Measuring spigot for standard plug gauges
DIN 226 edition 11.1924 → withdrawn
Measuring spigot for standard plug gauges
DIN 227 edition 4.1924 → withdrawn
Measuring spigot for limit plug gauges, working plug gauges and acceptance plug gauges
DIN 228 - Part 1 · Edition 5.1987 → current
Morse Taper and Metric Taper · Taper Shank
The standard specifies dimensions for Morse taper or metric taper, taper shaft. It is used for all standardized tools and clamping devices with Morse or metric taper shank for use with and without a central coolant supply.
DIN 228 - Part 1 · Edition 3.1987 → replaced by Edition 5.1987
Morse Taper and Metric Taper · Taper Shank
DIN 228 - Part 1 · Edition 7.1982 → replaced by Edition 3.1987
Morse Taper and Metric Taper · Taper Shank
DIN 228 - Part 1 · Edition 1.1981 → replaced by Edition 7.1982
Morse Taper and Metric Taper · Taper Shank
DIN 228 - Part 1 · Edition 4.1970 → withdrawn
Tool cone; Morse Taper and Metric Taper Taper Shanks
DIN 228 - Part 1 · Edition 10.1943 → withdrawn
Tool cones, conical shanks for tools
DIN 228 - Part 2 · Edition 3.1987 → current
Morse Taper and Metric Taper · Tapered Sleeves
The standard specifies dimensions for Morse taper or metric taper and taper sleeves. It is used for all standardized tool holders with Morse or metric taper sleeves for use with and without a central coolant supply.
DIN 228 - Part 2 · Edition 7.1982 → replaced by Edition 3.1987
Morse Taper and Metric Taper · Tapered Sleeves
DIN 228 - Part 2 · Edition 1.1981 → replaced by Edition 7.1982
Morse Taper and Metric Taper · Tapered Sleeves
DIN 228 - Part 2 · Edition 1.1959 → withdrawn
Tool cone; Morse taper and metric taper; Conical sleeves
DIN 228 - Part 2 · Edition 10.1943 → withdrawn
Tool cones, internal cones for machine tools
DIN 228 · Edition 7.1925 → withdrawn
Tool cone, shank and sleeve, construction sheet
DIN 229 - Part 1 Edition 8.1982 → current
Morse taper gauges · Taper plug gauges
DIN 229 - Part 1 Edition 7.1963 → withdrawn
Morse taper gauges; Cone plug gauges
DIN 229 - part 2 edition 8.1982 → current
Morse taper gauges · Taper gauge sleeves
DIN 229 - Part 2 Edition 7.1963 → withdrawn
Morse taper gauges; Conical sleeves
DIN 229 edition 10.1922 → withdrawn
Morse taper gauges, mandrel and sleeve, short version, without rag
DIN 230 - Part 1 · Edition 8.1982 → current
Morse taper gauges; Taper plug gauges for taper sleeves with drive slot
DIN 230 - Part 1 · Edition 5.1963 → withdrawn
Morse taper gauges; Taper plug gauges with flaps
DIN 230 - Part 2 · Edition 8.1982 → current
Morse taper gauges; Taper sleeves for taper shanks with driving tabs
DIN 230 - Part 2 · Edition 5.1963 → withdrawn
Morse taper gauges; Conical sleeves with flaps
DIN 230 edition 11.1924 → withdrawn
Morse taper gauges, mandrel and sleeve, short version, with rag
DIN 231 edition 9.1924 → withdrawn
Morse taper, shank and sleeve
DIN 232 Edition 3.1943 → withdrawn
Transition from the taper shank to the cutting part of the tool
DIN 232 · Edition 4.1924 → withdrawn
Transition from tool taper to stronger shank, guidelines
DIN 233 Edition 7.1925 → withdrawn
Metric taper, stem and sleeve
DIN 234 - Part 1 Edition 8.1982 → current
Metric cone gauges; Cone plug gauges
DIN 234 - Part 1 · Edition 5.1963 → withdrawn
Metric cone gauges; Cone plug gauges
DIN 234 - Part 2 Edition 8.1982 → current
Metric cone gauges; Conical sleeves
DIN 234 - Part 2 · Edition 5.1963 → withdrawn
Metric cone gauges; Conical sleeves
DIN 234 edition 10.1922 → withdrawn
Metric taper gauges, mandrel and sleeve, short version, without tab
DIN 235 - Part 1 Edition 8.1982 → current
Metric cone gauges; Taper plug gauges for taper sleeves with drive slot
DIN 235 - Part 1 · Edition 5.1963 → withdrawn
Metric cone gauges; Taper plug gauges with flaps
DIN 235 - Part 2 Edition 8.1982 → current
Metric cone gauges; Taper sleeves for taper shanks with driving tabs
DIN 235 - Part 2 · Edition 5.1963 → withdrawn
Metric cone gauges; Conical sleeves with flaps
DIN 235 edition 10.1922 → withdrawn
Metric taper gauges, mandrel and sleeve, short version, with rag
DIN 236 edition 7.1928 → withdrawn
Standard plug gauges
DIN 236 edition 4.1925 → withdrawn
Standard plug gauges
DIN 237 edition 7.1928 → withdrawn
Normal ring gauges
DIN 237 edition 11.1924 → withdrawn
Normal ring gauges
DIN 238 Edition 2.2005 → current
Drill chuck holder · Taper mandrels
This standard applies to drill chuck holders with drill chuck taper and Jacobs taper.
DIN 238 - Part 1 · Edition 6.1962 → replaced by DIN 238 Edition 2.2005
Drill chuck holder · Taper mandrels
DIN 238 - Part 1 Issue 3.1943 → withdrawn
Taper mandrels for drill chucks
DIN 238 - Part 2 Edition 3.1967 → 12.2003 withdrawn without replacement
Drill chuck holder · drill chuck taper
DIN 238 - Part 2 · Edition 2.1943 → withdrawn
Drill chuck cone, connection dimensions
DIN 238 Edition 10.1927 → withdrawn
Drill chuck taper
DIN 238 edition 4.1924 → withdrawn
Drill chuck taper
DIN 239 edition 2.1923 → withdrawn
Whitworth fine thread 1, from 56 to 499 mm in diameter
DIN 240 · Edition 2.1923 → withdrawn
Whitworth fine thread 2, from 20 to 189 mm in diameter
DIN 241 edition 2.1923 → withdrawn
Metric fine thread 1 from 154 to 499 mm in diameter
DIN 242 edition 2.1923 → withdrawn
Metric fine thread 2 from 24 to 189 mm in diameter
DIN 243 edition 9.1943 → withdrawn
Metric fine thread from 1 to 300 mm nominal thread diameter, theoretical values, selection series
DIN 243 - Part 1 · Edition 2.1923 → withdrawn
Metric fine thread 3 from 1 to 34 mm in diameter
DIN 243 - Part 2 · Edition 2.1923 → withdrawn
Metric fine thread 3 from 35 to 100 mm in diameter
DIN 243 - Part 3 · Edition 2.1923 → withdrawn
Metric fine thread 3 from 102 to 300 mm in diameter
DIN 244 edition 12.1952 → withdrawn
Metric fine thread with pitch h 6 mm
DIN 244 edition 9.1943 → withdrawn
Metric fine thread with pitch h 6 mm, theoretical values
DIN 245 edition 12.1952 → withdrawn
Metric fine thread with pitch h 4 mm
DIN 245 · Edition 9.1943 → withdrawn
Metric fine thread with pitch h 4 mm, theoretical values
DIN 246 edition 12.1952 → withdrawn
Metric fine thread with pitch h 3 mm
DIN 246 edition 9.1943 → withdrawn
Metric fine thread with pitch h 3 mm, theoretical values
DIN 247 edition 12.1952 → withdrawn
Metric fine thread with pitch h 2 mm
DIN 247 edition 9.1943 → withdrawn
Metric fine thread with pitch h 2 mm, theoretical values
DIN 248 edition 10.1967 → 7.2006 withdrawn without replacement
Square ring spanner
DIN 248 · Edition 5.1933 → withdrawn
Square wrench, closed
DIN 249 edition 10.1922 → withdrawn
Limit gauges, marking and labeling
For this purpose, draft DIN 2259-1 for a new edition
DIN 250 · Edition 4.2002 → current
Radii
The standard contains the radii on workpieces of all types. The dimensions of the rounding radii correspond to the standard series of numbers R5, R10 and R20 according to DIN 323-1. Some values are taken from the associated rounding series R <second> 5, R <minute> 10 and R <second> 10.
DIN 250 edition 7.1972 → replaced by edition 4.2002
Rounding radius
DIN 250 edition 12.1939 → withdrawn
Roundings
3rd edition
DIN 250 edition 9.1939 → withdrawn
Roundings
DIN 250 edition 4.1924 → withdrawn
Roundings
DIN 251 edition 1.1927 → withdrawn without replacement
Out of round
The standard defines the dimensions of profiles that are used as oval flanges and flange gates in three rows.
DIN 252 edition 4.1924 → withdrawn
One-sided push-in handles for measuring tools
DIN 253 edition 4.1924 → withdrawn
Double-sided insert handles for measuring tools
DIN 254 edition 4.2003 → current
Geometrical Product Specifications (GPS) - sets of cones and cone angles; Values for setting angles and setting heights
In addition to DIN EN ISO 1119, edition 1998, the standard contains the terms cone, setting angle and setting heights and their definitions, some additional cones and the dimensions for setting angles and setting heights.
DIN 254 edition 10.2000 → 4.2003 replaced by edition 4.2003 and DIN EN ISO 1119 edition 4.2003
Geometrical Product Specifications (GPS) - Cones
The standard applies to cones with a cone angle of up to 165 ° for general areas of application. It does not apply to special cases, such as bevel gears.
DIN 254 · Edition 6.1974 → replaced by Edition 10.2000
cone
DIN 254 edition 7.1962 → replaced by edition 6.1974
Cone; Terms and preferred values
DIN 254 edition 12.1939 → withdrawn
cone
DIN 254 edition 1.1922 → withdrawn
cone
DIN 255 · Edition 10.1928 → withdrawn
Fixed cone handles
DIN 255 edition 11.1919 → withdrawn
Fixed cone handles
DIN 256 edition 10.1928 → withdrawn
Rotatable conical handles
DIN 256 edition 11.1919 → withdrawn
Rotatable conical handles
DIN 257 edition 7.1936 → 11.1968 withdrawn without replacement
Taper pins ; with threaded pin; Whitworth thread 1/4 "to 1½"
DIN 257 edition 9.1921 → withdrawn
Tapered pins with threaded stem, Whitworth thread
DIN 258 edition 5.2012 → current
Taper pins with threaded pin and constant taper lengths
DIN 258 edition 2.2011 → replaced by edition 5.2012
Taper pins with threaded pin and constant taper lengths
DIN 258 edition 2.1977 → replaced by edition 2.2011
Taper pins with threaded pin and constant taper lengths
DIN 258 Edition 3.1961 → replaced by Edition 2.1977
Taper pins; with threaded pin and constant taper lengths
DIN 258 edition 1.1943 → withdrawn
Taper pins with threaded pin, M 5 to M 36
DIN 258 edition 9.1921 → withdrawn
Taper pins with threaded stem, metric thread
DIN 259 - Part 1 Edition 8.1979 → 4.1985 replaced by DIN ISO 228-1
Whitworth pipe threads; Cylindrical internal and cylindrical external threads; Nominal dimensions (not for new designs)
DIN 259 - Part 1 · Edition 6.1966 → replaced by Edition 8.1979
Whitworth pipe threads; Cylindrical internal and cylindrical external thread
DIN 259 - Part 2 Edition 8.1979 → 4.1985 replaced by DIN ISO 228-1
Whitworth pipe threads; Cylindrical internal and cylindrical external threads; Tolerances (not for new designs)
DIN 259 - Part 2 · Edition 6.1966 → replaced by Edition 8.1979
Whitworth pipe threads; Cylindrical internal and cylindrical external thread tolerances
DIN 259 - Part 3 Edition 8.1979 → 4.1985 replaced by DIN ISO 228-1
Whitworth pipe threads; Cylindrical internal and cylindrical external threads; Limit dimensions (not for new designs)
DIN 259 - Part 3 · Edition 6.1966 → replaced by Edition 8.1979
Whitworth pipe threads; Cylindrical internal and cylindrical external thread limit dimensions
DIN 259 - Part 4 Edition 10.1976 → 12.1984 replaced by DIN ISO 228-2
Whitworth pipe threads; Cylindrical internal and cylindrical external thread, gauge of the external thread, gauge dimensions
DIN 259 - Part 5 Edition 10.1976 → 12.1984 replaced by DIN ISO 228-2
Whitworth pipe threads; Cylindrical internal and cylindrical external thread, gauge of the internal thread, gauge dimensions
DIN 259 edition 11.1942 → withdrawn
Whitworth pipe threads
DIN 259 edition 10.1927 → withdrawn
Whitworth pipe thread without point clearance
DIN 259 edition 8.1924 → withdrawn
Whitworth pipe thread without point clearance
DIN 260 edition 10.1927 → withdrawn
Whitworth pipe thread with point clearance
DIN 260 edition 8.1924 → withdrawn
Whitworth pipe thread with point clearance
DIN 261 Edition 12.2010 → current
T-head bolts
The standard contains the dimensional specifications and technical delivery conditions of T-head bolts with thread for fastening components with the help of T-slots, on foundations or other constructions and specifies their designation.
DIN 261 edition 1.1987 → replaced by edition 12.2010
T-head bolts
DIN 261 edition 12.1970 → replaced by edition 1.1987
T-head bolts
DIN 261 - Part 1 · Edition 1.1942 → withdrawn
T-head bolts; M 10 to 100
DIN 261 - Part 2 Edition 7.1936x → withdrawn
T-head bolts; 5/8 "to 2 1/2", W 72 × 1/4 "to W 99 × 1/4"
DIN 261 edition 4.1927 → withdrawn
T-head bolts
DIN 261 edition 6.1923 → withdrawn
T-head bolts
DIN 262 - Part 1 · Edition 5.1973 → current
Round thread with clearance and steep flank, with a pitch of 7 mm · nominal dimensions
DIN 262 - Part 2 · Edition 5.1973 → current
Round thread with play and steep flank, with a pitch of 7 mm · Thread limit dimensions and dimensions, permissible deviations and permissible wear of the thread gauges
DIN 262 Edition 7.1937 → withdrawn
Round thread with point and flank play, for coupling spindles of old design, draw hooks and brake pull rods
DIN 262 - Supplement · Edition 4.1936 → withdrawn
Round thread with point and flank play, thread limit dimensions, manufacturing accuracy and wear of the thread gauges
DIN 262 edition 4.1928 → withdrawn
Round thread with point and flank play for coupling spindles of old design, draw hooks and brake tie rods
DIN 262 - Supplement · Edition 4.1928 → withdrawn
Thread limit dimensions of the workpieces, manufacturing accuracy and wear of the gauges
DIN 262 Edition 7.1925 → withdrawn
Round thread with point and flank play for coupling spindles of old design, draw hooks and brake tie rods (railways)
DIN 263 - Part 1 · Edition 3.2000 → current
Trapezoidal thread, single and double start, with clearance, for rail vehicles · Dimensions
Threads according to this standard are mainly used for brake spindles on rail vehicles.
DIN 263 - Part 1 edition 11.1977 → replaced by edition 3.2000
Trapezoidal thread, single and double start, with clearance, for rail vehicles · Theoretical values
DIN 263 - Part 1 · Edition 10.1969 → replaced by Edition 11.1977
Trapezoidal thread, single and double start, with clearance, for rail vehicles · Theoretical values
DIN 263 - Part 2 Edition 3.2000 → 10.2006 withdrawn without replacement
Trapezoidal thread, single and double start, with clearance, for rail vehicles · Thread limit dimensions and limit dimensions
Threads according to this standard are mainly used for brake spindles on rail vehicles.
DIN 263 - Part 2 Edition 11.1977 → replaced by Edition 3.2000
Trapezoidal thread, single and double start, with play, for rail vehicles · Thread limit dimensions and dimensions, permissible manufacturing deviations and permissible wear of the thread gauges
DIN 263 - Part 2 · Edition 10.1969 → replaced by Edition 11.1977
Trapezoidal thread single and double with play; for rail vehicles, thread limit dimensions and dimensions, permissible manufacturing deviations and permissible wear of the thread gauges
DIN 263 - Part 3 · Edition 6.2003 → current
Trapezoidal thread, single and double start, with clearance, for rail vehicles · Thread gauges, gauge dimensions and permissible wear of the gauges
The gauges and gauge dimensions specified in the standard as well as the permissible wear of the thread gauges apply to the trapezoidal thread according to DIN 263 Part 1 and DIN 263 Part 2.
DIN 263 edition 5.1924 → withdrawn
Brake spindle thread, double trapezoidal thread
DIN 264 - Part 1 · Edition 5.1973 → current
Round thread with play and flat flank, with a pitch of 7 mm · nominal dimensions
DIN 264 - Part 2 · Edition 5.1973 → current
Round thread with clearance and flat flank, with a pitch of 7 mm · Thread limit dimensions and dimensions, permissible deviations and permissible wear of the thread gauges
DIN 264 Edition 7.1937 → withdrawn
Round thread with point and flank play, for coupling spindles, design 1925
DIN 264 edition 10.1928 → withdrawn
Round thread with point and flank play for coupling spindles design 1925
DIN 265 - Part 1 · Edition 4.1927 → withdrawn
Rivets under 10 mm, overview
DIN 265 - Part 2 Edition 7.1925 → withdrawn
Rivets 10 to 43 mm, overview of riveted connections
DIN 265 edition 7.1925 → withdrawn
Riveted connections, overview
DIN 267 - Part 1 Edition 11.1967 → withdrawn
Screws, nuts and similar threaded and shaped parts; Technical delivery conditions, general information
DIN 267 - Part 2 · Edition 6.2017 → current
Mechanical fasteners · Technical delivery conditions, surface roughness for product classes A and B
In addition to DIN EN ISO 4759 Part 1, the standard specifies requirements for surface roughness of mechanical connecting elements of product classes A and B.
DIN 267 - Part 2 Edition 11.1984 → replaced by Edition 6.2017
Mechanical fasteners · Technical delivery conditions, design and dimensional accuracy
The standard supplements the international standard ISO 4759 Part 1. It contains information on the design and dimensional accuracy of the technical delivery conditions for mechanical connecting elements.
DIN 267 - Part 2 · Edition 4.1968 → replaced by Edition 11.1984 and DIN ISO 4759 Part 1 Edition 5.1980
Screws, nuts and similar threaded and molded parts · Technical delivery conditions, design and dimensional accuracy
DIN 267 - Part 3 Edition 8.1983 → 9.2004 withdrawn without replacement
Mechanical fasteners - Terms of delivery · Strength classes for screws made of unalloyed or alloyed steels; Conversion of the strength classes
DIN 267 - Part 3 Edition 10.1967 → withdrawn
Screws, nuts and similar threaded and shaped parts; Strength classes and test methods for screws made of unalloyed or low-alloy steels, technical delivery conditions
DIN 267 - Part 4 Edition 8.1983 → withdrawn
Mechanical fasteners - Technical delivery conditions; Strength classes for nuts (previous classes)
DIN 267 - part 4 edition 10.1971 → replaced by edition 8.1983, DIN 267 part 21 edition 6.1981 and DIN 267 part 24 edition 8.1983
Screws, nuts and similar threaded and shaped parts Technical delivery conditions; Property classes and test methods for nuts made from unalloyed or low-alloy steels
DIN 267 - Part 5 Edition 2.1986 → withdrawn
Mechanical fasteners - Technical delivery conditions; Acceptance test ISO 3269 edition 1984 modified
DIN 267 - Part 5 · Edition 4.1968 → withdrawn
Screws, nuts and similar threaded and shaped parts; Technical delivery conditions, testing and acceptance
DIN 267 - Part 6 Edition 9.1975 → withdrawn
Mechanical fasteners - technical delivery conditions · Designs and dimensional accuracy for product class F
DIN 267 - Part 7 · Edition 5.1968 → withdrawn
Screws, nuts and similar threaded and shaped parts; Technical delivery conditions, labeling and delivery type for screws made of unalloyed or low-alloy steels
DIN 267 - Part 8 Edition 10.1971 → replaced by DIN 267 Part 4 Edition 8.1983 and DIN 267 Part 24 Edition 8.1983
Screws, nuts and similar threaded and shaped parts; Technical delivery conditions, labeling and delivery type for nuts made of unalloyed or low-alloy steels
DIN 267 - Part 9 Edition 8.1979 → withdrawn
Mechanical fasteners - Technical delivery conditions; Parts with galvanic coatings
DIN 267 - Part 9 · Edition 5.1968 → replaced by Edition 8.1979
Screws, nuts and similar threaded and shaped parts; Technical delivery conditions Bolts and nuts with galvanic coatings
DIN 267 - part 10 edition 1.1988 → replaced by DIN EN ISO 10684 edition 11.2004
Mechanical fasteners - Technical delivery conditions · Technical delivery conditions; Hot-dip galvanized parts
The standard specifies the special requirements for hot-dip galvanized parts with threads. In detail, these are the limit dimensions of the thread before galvanizing as well as the minimum zinc requirements and their testing. In addition, the test forces and the minimum breaking forces for hot-dip galvanized screws are given. The standard applies to parts with threads from M 6 to M 36 and strength classes up to 10.9 for screws and 10 for nuts.
DIN 267 - Part 11 Edition 1.1980 → replaced by DIN EN ISO 3506
Mechanical fasteners - Technical delivery conditions with additions to ISO 3506; Parts made from rust and acid-proof steels
DIN 267 - Part 11 · Edition 5.1968 → withdrawn
Screws, nuts and similar threaded and shaped parts; Technical delivery conditions Bolts and nuts made of stainless steels
DIN 267 - Part 12 Edition 11.1971 → withdrawn
Screws, nuts and similar threaded and shaped parts; Technical delivery conditions sheet metal screws
DIN 267 - Part 13 · Edition 5.2007 → current
Mechanical fasteners - technical delivery conditions · Parts for screw connections with special mechanical properties for use at temperatures from -200 ° C to +700 ° C
The standard specifies the mechanical properties of parts for screw connections that are used in safety-relevant areas at temperatures between -200 ° C and +700 ° C.
DIN 267 - Part 13 · Edition 8.1993 → replaced by Edition 5.2007
Mechanical fasteners - technical delivery conditions · Parts for screw connections with special mechanical properties for use at temperatures from -200 ° C to +700 ° C
DIN 267 - Part 13 · Edition 3.1980 → replaced by Edition 8.1993 and DIN 267 Part 29 Edition 8.1993
Mechanical connecting elements · Technical delivery conditions · Parts for screw connections, mainly made of cold-tough or heat-resistant materials
DIN 267 - Part 13 · Edition 7.1968 → withdrawn
Screws, nuts and similar threaded and molded parts · Technical delivery conditions, screws and nuts mainly made of cold-tough or heat-resistant steels
DIN 267 - Part 15 · Edition 11.1983 → withdrawn
Mechanical fasteners - Technical delivery conditions; Nuts with clamping part
DIN 267 - Part 15 · Edition 10.1971 → replaced by Edition 11.1983
Screws, nuts and similar threaded and shaped parts Technical delivery conditions; Strength classes and test methods for lock nuts
DIN 267 - Part 18 → 12.1991 replaced by DIN EN 28839
DIN 267 - Part 19 → 12.1991 replaced by DIN EN 26157-1 and 3
DIN 267 - Part 20 → 7.1992 replaced by DIN EN 493
DIN 267 - Part 21 → 7.1992 replaced by DIN EN 493
DIN 267 - Part 23 → 2.1996 replaced by DIN EN ISO 898-6
DIN 267 - Part 24 · Edition 10.2007 → current
Mechanical fasteners - Technical delivery conditions - Hardness classes for nuts without specified test forces
DIN 267 - part 24 edition 8.1983 → replaced by edition 10.2007
Mechanical fasteners - technical delivery conditions, strength classes for nuts (hardness classes)
DIN 267 - Part 25 Edition 4.1995 → replaced by DIN EN 20898-7
DIN 267 - Part 26 · Edition 12.2005 → current
Mechanical fasteners - technical delivery conditions · Spring steel spring washers for screw connections
The standard specifies the technical delivery conditions for spring steel spring washers, which are used in screw connections to reduce the loss of prestressing force due to setting.
DIN 267 - part 26 edition 10.1987 → replaced by edition 12.2005
Mechanical connecting elements - technical delivery conditions · Spring steel elements for screw connections
The standard specifies the technical delivery conditions for tensioned spring elements made of spring steel that are used in screw connections.
DIN 267 - Part 27 · Edition 9.2009 → current
Mechanical fasteners · screws made of steel with adhesive coating; Technical delivery conditions
The standard specifies the technical delivery conditions for screws made of steel with an adhesive coating.
DIN 267 - Part 27 · Edition 1.2004 → replaced by Edition 9.2009
Mechanical fasteners · screws made of steel with adhesive coating; Technical delivery conditions
DIN 267 - Part 27 · Edition 3.1990 → replaced by Edition 1.2004
Mechanical fasteners · screws made of steel with adhesive coating; Technical delivery conditions
The standard specifies the technical delivery conditions for screws made of steel with an adhesive coating.
DIN 267 - Part 28 · Edition 9.2009 → current
Mechanical fasteners · screws made of steel with clamping coating; Technical delivery conditions
The standard specifies the technical delivery conditions for screws made of steel with a clamping coating.
DIN 267 - Part 28 Correction 1 · Edition 11.2004 → replaced by Edition 9.2009
Corrections to DIN 267 Part 28 Edition 1.2004
DIN 267 - Part 28 · Edition 1.2004 → replaced by DIN 267 - Part 28 Correction 1 Edition 11.2004 and Edition 9.2009
Mechanical fasteners · screws made of steel with clamping coating; Technical delivery conditions
DIN 267 - Part 28 Edition 3.1990 → replaced by Edition 1.2004
Screws made of steel with clamping coating; Technical delivery conditions
DIN 267 - Part 29 Edition 8.1993 → current
Mechanical fasteners · Product classes for parts for screw connections for use at temperatures from -200 ° C to +700 ° C
The standard specifies product classes for parts for screw connections for use at temperatures of -200 ° C and +700 ° C.
DIN 267 - Part 30 · Edition 12.2016 → current
Mechanical fasteners · Technical delivery conditions · Metric self-tapping screws of strength class 10.9
The standard specifies the requirements for metric self-tapping screws of strength class 10.9. Screws according to this standard produce internal threads with diameters of 2.5 to 10 mm, which match metric ISO threads. The material in which the screws are used may not have a hardness of more than 130 HV 10 or 124 HB.
DIN 267 - Part 30 · Edition 4.2008 → replaced by Edition 12.2016
Mechanical fasteners · Technical delivery conditions · Metric self-tapping screws of strength class 10.9
The standard contains the requirements for metric self-tapping screws of strength class 10.9 and specifies their designation.
DIN 267 - Part 30 · Edition 2.2001 → replaced by Edition 4.2008
Mechanical fasteners · Technical delivery conditions · Metric self-tapping screws of strength class 10.9
The standard contains the requirements for metric self-tapping screws of strength class 10.9 and specifies their designation.
DIN 267 · Edition 12.1960 → replaced by DIN 267 Part 1 Edition 8.1982, DIN 267 Part 2 Edition 4.1968, DIN 267 Part 4 Edition 8.1983, DIN 267 Part 5 Edition 4.1968 and a.
Screws, nuts and similar threaded and molded parts · Technical delivery conditions
DIN 267 edition 1.1943 → withdrawn
Screws, nuts and similar threaded and molded parts · Technical delivery conditions
DIN 267 supplement 1 edition 11.1943 → withdrawn
Screws and nuts; Simplifications for manufacturing
DIN 268 Edition 9.1974 → current
Tangent keys and tangent keyways for sudden alternating loads
DIN 268 edition 4.1924 → withdrawn
Tangent keyways; for sudden alternating pressure
DIN 269 edition 4.1924 → withdrawn
Parallel keys, sliding springs, application sheet
DIN 270 edition 8.1924 → withdrawn
Parallel keys for turbo pumps and turbo blowers, application sheet
DIN 271 edition 9.1974 → current
Tangent keys and tangent keyways for constant loads
DIN 271 edition 4.1924 → withdrawn
Tangent keyways
Dimensional standard
DIN 272 Edition 2.1986 → current
Testing of magnesia screed
The standard specifies the methods for determining the material properties of magnesia screed. These properties are the bulk density, the surface hardness, the consistency, the change in length and the mixing ratio of caustic magnesia and magnesium chloride. It thus supplements DIN 18560, in which the testing of the requirements for screeds is specified regardless of the type of binder used.
DIN 272 edition 3.1978 → replaced by edition 2.1986 and DIN 18560 part 1 edition 8.1981
Magnesia screeds (screeds made from magnesia mortar)
DIN 272 Edition 7.1963 → withdrawn
Magnesia screeds; (Screeds made of magnesia mortar)
DIN 272 - Part 1 · Edition 6.1943 → withdrawn
Stone wood, industrial and rammed floors
DIN 272 - Part 2 · Edition 6.1943 → withdrawn
Stone wood, stone wood floors
DIN 272 - Part 3 · Edition 6.1943 → withdrawn
Stone wood, stone wood sub-floors for linoleum, parquet, etc.
DIN 272 - Part 4 Edition 6.1943 → withdrawn
Stone wood, subsoil
DIN 272 - Part 5 · Edition 6.1943 → withdrawn
Stone wood, test regulations
DIN 272 edition 11.1930 → withdrawn
Stone wood for floors, concept, thickness, properties, test methods
DIN 272 Edition 10.1919 (Reichsnorm) → withdrawn
Simple three-pane windows without transom, low panes
DIN 273 - part 1 edition 5.1981 → replaced by DIN EN 14016 part 1 and part 2 edition 4.2004
Base materials for magnesia screeds · Caustic magnesia
DIN 273 - Part 2 Edition 7.1983 → replaced by DIN EN 14016 Part 1 and Part 2 Edition 4.2004
Starting materials for magnesia screeds · Magnesium chloride
DIN 273 - Part 2 · Edition 7.1963 → withdrawn
Starting materials for magnesia screeds (screeds made from magnesia mortar); Magnesium chloride
DIN 273 - Part 3 · Edition 7.1963 → withdrawn
Starting materials for magnesia screeds (screeds made from magnesia mortar); Fillers
DIN 273 - Part 1 · Edition 6.1943 → withdrawn
Stone wood, raw materials, caustic magnesia (caustic burned magnesite)
DIN 273 - Part 2 · Edition 6.1943 → withdrawn
Stone wood, raw materials, magnesium chloride
DIN 273 - Part 3 · Edition 6.1943 → withdrawn
Stone wood, raw materials, fillers
DIN 273 edition 10.1919 (Reichsnorm) → withdrawn
Three-pane double windows without transom, low panes
DIN 274 - Part 1 Issue 4.1972 → 7.1992 withdrawn without replacement
Asbestos cement corrugated sheets; Dimensions, requirements, tests
DIN 274 - Part 2 Edition 4.1972 → 7.1992 withdrawn without replacement
Asbestos cement corrugated sheets; Use in roofing
DIN 274 - Part 3 Edition 12.1976 → 7.1992 withdrawn without replacement
Asbestos cement panels; Flat roof panels, dimensions, requirements, tests
DIN 274 - Part 4 Edition 8.1978 → 7.1992 withdrawn without replacement
Asbestos cement panels; Level boards, dimensions, requirements, tests
DIN 274 - Part 5 Draft edition 9.1982 → 11.1985 replaced by DIN 18517-1
Asbestos cement panels; Small format asbestos cement panels; Use in exterior wall cladding
DIN 274 Edition 10.1936 → withdrawn
Asbestos-cement roofing sheets and asbestos-cement sheets, terms of delivery and testing
DIN 274 edition 10.1919 (Reichsnorm) → withdrawn
Simple four-pane windows without transom, low panes
DIN 275 edition 5.1979 → current
House number lights; execution
DIN 275 edition 11.1966 → withdrawn
House number lights; Arrangement execution
DIN 275 edition 2.1935 → withdrawn
House number lights; Arrangement, execution
DIN 275 edition 10.1919 (Reichsnorm) → withdrawn
Four-pane double windows without transom, low panes
DIN 276 Edition 12.2018 → current
Construction costs
The standard applies to the determination and classification of costs for new construction, renovation and modernization of engineering structures and traffic systems.
DIN 276 - Part 4 Edition 8.2009 → replaced by DIN 276 Edition 12.2018
Construction costs · Civil engineering
The standard applies in particular to the determination and classification of costs for new construction, reconstruction and modernization of engineering structures and traffic systems.
DIN 276 - part 1 edition 12.2008 → replaced by DIN 276 edition 12.2018
Construction costs · Building construction
The standard applies to the determination and classification of costs in building construction. It records the costs for measures for the production, conversion and modernization of the buildings as well as the associated expenses. The standard defines terms and distinguishing features and thus creates the prerequisites for the comparability of the results of cost determinations that are carried out on the basis of the results of the construction planning.
DIN 276 - Part 1 Correction · Edition 2.2007 → replaced by DIN 276 Part 1 Edition 12.2008
Costs in construction · Building construction, corrections to DIN 276 Part 1 edition 11.2006
DIN 276 - Part 1 · Edition 11.2006 → replaced by DIN 276 Part 1 Correction Edition 2.2007
Construction costs · Building construction
The standard applies to the determination and classification of costs in building construction. It records the costs for measures for the production, conversion and modernization of the buildings as well as the associated expenses. The standard defines terms and distinguishing features and thus creates the prerequisites for the comparability of the results of cost determinations that are carried out on the basis of the results of the construction planning.
DIN 276 edition 6.1993 → replaced by DIN 276 part 1 edition 11.2006
Building construction costs
DIN 276 edition 8.1943 → withdrawn
Buildings, costs
DIN 276 - Supplement · Edition 7.1943 → withdrawn
Buildings, costs; Comparative overview of costs, built-up space and price per meter of built buildings
also applies to DIN 277
DIN 276 edition 10.1919 (Reichsnorm) → withdrawn
Simple four-pane windows with transom, low panes
DIN 276 - Part 1 · Edition 4.1981 → replaced by DIN 276 Edition 6.1993
Costs of buildings · Terms
DIN 276 - Part 1 · Edition 9.1971 → replaced by Edition 4.1981
Costs of buildings · Terms
DIN 276 - Part 2 · Edition 4.1981 → replaced by DIN 276 Edition 6.1993
Costs of buildings · Breakdown of costs
DIN 276 - Part 2 · Edition 9.1971 → replaced by Edition 4.1981
Costs of buildings · Breakdown of costs
DIN 276 - Part 3 · Edition 4.1981 → replaced by DIN 276 Edition 6.1993
Costs of building structures · Cost assessments
DIN 276 - Part 3 Selection 1 · Edition 4.1981 → replaced by DIN 276 Edition 6.1993
Building Construction Costs · Costing · Selection for Housing
DIN 276 - Part 3 · Edition 9.1971 → replaced by Edition 4.1981
Costs of building structures · Cost assessments
DIN 277 - Part 1 · Edition 1.2016 → current
Floor areas and volumes in construction · Building construction
This standard specifies the rules for calculating the area and volume of buildings. Surface and room contents serve both to determine the production costs of buildings and to determine rental and purchase prices. They are also used to compare the usability and profitability of different buildings.
DIN 277 - Part 1 · Edition 2.2005 → replaced by Edition 1.2016
Base areas and volume of structures in building construction · Terms, bases for determination
DIN 277 - Part 2 edition 2.2005 → replaced by DIN 277-1 edition 1.2016
Base areas and volume of buildings in building constructionSubdivision of the net base area (usable areas, technical functional areas and traffic areas)
This standard divides the usable area of buildings defined in DIN 277 Part 1 into groups of different types of use and gives examples for the allocation of rooms and areas to the individual types of use. The standard is particularly applicable when determining the area of buildings with multiple uses.
DIN 277 - Part 3 Edition 4.2005 → replaced by DIN 276 Edition 12.2018
Base areas and volumes of buildings in building construction · Quantities and reference units
This standard specifies the measured variables and reference units for building cost groups on the basis of DIN 276.
DIN 277 - Part 3 · Edition 2.2005 → replaced by Edition 4.2005
Base areas and volumes of buildings in building construction · Quantities and reference units
This standard specifies the measured variables and reference units for building cost groups on the basis of DIN 276.
DIN 277 - Part 3 · Edition 7.1998 → replaced by Edition 2.2005
Base areas and volumes of buildings in building construction · Quantities and reference units
This standard specifies the measured variables and reference units for building cost groups on the basis of DIN 276.
DIN 277 - Part 1 · Edition 6.1987 → replaced by Edition 2.2005
Base areas and volume of structures in building construction · Terms, calculation bases
This standard specifies the rules for calculating the area and volume of structures of structures. Area and room contents are used both to determine the production costs of buildings and to determine rental and purchase prices. They are also used to compare the usability and profitability of different buildings.
DIN 277 - Part 2 · Edition 6.1987 → replaced by Edition 2.2005
Floor space and volume of buildings in building constructionSeparation of usable areas, functional areas and traffic areas (net floor area)
This standard divides the usable area of buildings defined in DIN 277 Part 1 into groups of different types of use and gives examples for the allocation of rooms and areas to the individual types of use. The standard is particularly applicable when determining the area of buildings with multiple uses.
DIN 277 - Part 2 · Edition 3.1981 → replaced by Edition 6.1987
Floor areas and volume of high-rise buildings Structure of the usable areas, functional areas and traffic areas (net floor plan area)
DIN 277 - Part 1 · Edition 5.1973 → replaced by Edition 6.1987
Floor areas and volume of buildings · Terms, calculation bases
DIN 277 edition 11.1950 → withdrawn
Buildings · Enclosed space, price per meter
New version based on the calculation method of the 1.1936 edition
DIN 277 - Supplement · Edition 7.1943 → withdrawn
Buildings, costs; Comparative overview of costs, built-up space and price per meter of built buildings
also applies to DIN 276
DIN 277 edition 10.1940x → withdrawn
Buildings, enclosed space
DIN 277 edition 1.1936 → withdrawn
Buildings · Enclosed space, price per meter
DIN 277 edition 10.1919 (Reichsnorm) → withdrawn
Four-pane double windows with transom, low panes
DIN 278 Edition 3.2017 → current
Hollow clay slabs (Hourdis) - statically stressed
The standard specifies the scope, requirements and testing of hollow clay plates (hourdis).
DIN 278 edition 9.1978 → replaced by edition 3.2017
Hollow clay slabs (hourdis) and hollow bricks, statically stressed
DIN 278 edition 4.1938 → withdrawn
Hollow clay plates (Hourdis)
DIN 278 Edition 10.1919 (Reichsnorm) → withdrawn
Simple three-pane windows without transom, high panes
DIN 279 edition 3.1966 → withdrawn without replacement
Cable protection hoods
DIN 279 edition 9.1937 → withdrawn
Cable protection hoods made of clay for low voltage cables, delivery conditions and test regulations
DIN 279 edition 10.1919 (Reichsnorm) → withdrawn
Three-pane double windows without transom, high panes
DIN 280 - Part 1 edition 4.1990 → 3.2006 replaced by DIN EN 13226 edition 5.2003
Parquet · Parquet strips, parquet belts and boards for panel parquet
The standard applies to parquet strips, parquet belts and boards for panel parquet made of oak, red beech, ash, pine and other suitable European and overseas hardwoods and conifers.
DIN 280 - Part 2 · Edition 4.1990 → replaced by DIN EN 13488 Edition 5.2003
Parquet · Mosaic parquet slats
The standard applies to mosaic parquet lamellas made from oak and other suitable European and overseas hardwoods and conifers.
DIN 280 - Part 1 · Edition 12.1970 → withdrawn
Parquet; Parquet strips and boards for panel parquet
DIN 280 - Part 2 · Edition 12.1970 → withdrawn
Parquet; Mosaic parquet slats
DIN 280 - Part 3 · Edition 12.1970 → withdrawn
Parquet; Parquet straps
DIN 280 - Part 4 · Edition 6.1973 → withdrawn
Parquet; Parquet floorboards, parquet panels
DIN 280 - Part 5 · Edition 4.1990 → replaced by DIN EN 13489 Edition 5.2003
Parquet · Prefabricated parquet elements
The standard applies to prefabricated parquet elements with a bar-like and mosaic-like appearance made of oak and other European and overseas hardwoods and conifers.
DIN 280 - Part 5 · Edition 6.1973 → withdrawn
Parquet; Prefabricated parquet elements
DIN 280 · Edition 6.1937 → withdrawn
Parquet strips, dimensions, nature of the wood, processing
DIN 280 edition 10.1919 (Reichsnorm) → withdrawn
Simple three-pane windows with transom, high panes
DIN 281 edition 3.1994 → withdrawn
Parquet adhesives; Requirements, testing, processing instructions
The standard applies to parquet adhesives based on dissolved or dispersed binders.
DIN 281 edition 12.1973 → withdrawn
Parquet adhesives cold paintable; Requirements, testing
DIN 281 edition 8.1942 → withdrawn
Parquet adhesives, cold paintable
DIN 281 edition 10.1919 (Reichsnorm) → withdrawn
Three-pane double windows with transom, high panes
DIN 282 Edition 10.1919 (Reichsnorm) → withdrawn
Single and double pane windows, low and high panes
DIN 283 - Part 1 Edition 3.1951 → 8.1989 withdrawn without replacement
Apartments; Terms
DIN 283 - Part 2 Edition 2.1962 → 10.1983 withdrawn without replacement
Apartments; Calculation of living areas and usable areas
DIN 283 Edition 10.1919 (Reichsnorm) → withdrawn
Details of the simple windows
DIN 284 Edition 3.1936 → withdrawn
Boundary stone for imperial roads
DIN 284 edition 10.1919 (Reichsnorm) → withdrawn
Details of the box windows
DIN 285 edition 12.1940 → withdrawn
Combustion systems, industrial furnaces and free-standing chimneys; Drying out and heating up guidelines
DIN 287 edition 11.1921 → withdrawn
Single-flight wooden stairs for residential floors in small houses, straight, high gradients
DIN 288 edition 11.1921 → withdrawn
Single-flight wooden stairs for residential floors in small houses, straight, low inclines
DIN 289 edition 11.1921 → withdrawn
Single-flight wooden stairs for residential floors in small houses, with lower spiral steps, high inclines
DIN 290 edition 11.1921 → withdrawn
Single-flight wooden stairs for residential floors in small houses, with lower spiral steps, low inclines
DIN 291 edition 11.1921 → withdrawn
Single-flight wooden stairs for residential floors in small houses, with upper spiral steps, high inclines
DIN 292 edition 11.1921 → withdrawn
Single-flight wooden stairs for residential floors in small houses, with upper spiral steps, low inclines
DIN 293 edition 11.1921 → withdrawn
Single-flight wooden stairs for residential floors in small houses, details of the straight stairs
DIN 294 - Part 1 Edition 11.1921 → withdrawn
Single-flight wooden stairs for the residential floors of the small houses, details of the spiral posts with fixed railings
DIN 294 - Part 2 Edition 11.1921 → withdrawn
Single-flight wooden stairs for the residential floors of the small houses, details of the spiral posts with removable railings
DIN 295 edition 3.1920 (Reichsnorm) → withdrawn
Frame windows for small apartments; four-winged double window, 116x111 cm, without transom
DIN 295 - Supplement · Edition 3.1920 (Reichsnorm) → withdrawn
Frame windows for small apartments; Explanations
DIN 296 edition 3.1920 (Reichsnorm) → withdrawn
Frame windows for small apartments; four-sash double window, 116x142 cm, without transom
DIN 296 - supplementary sheet · Edition 3.1920 (Reichsnorm) → withdrawn
Frame windows for small apartments; Explanations
DIN 297 edition 3.1920 (Reichsnorm) → withdrawn
Frame windows for small apartments; Eight-sash double window, 116x154 cm, with a spider
DIN 297 - Supplement · Edition 3.1920 (Reichsnorm) → withdrawn
Frame windows for small apartments; Explanations
DIN 298 edition 3.1920x (Reichsnorm) → withdrawn
Frame windows for small apartments; Single sash windows
DIN 298 edition 3.1920 (Reichsnorm) → withdrawn
Frame windows for small apartments; Single sash windows
DIN 298 - Supplement · Edition 3.1920 (Reichsnorm) → withdrawn
Frame windows for small apartments; Explanations
DIN 299 edition 3.1920 (Reichsnorm) → withdrawn
Frame windows for small apartments; details
DIN 299 - Supplement · Edition 3.1920 (Reichsnorm) → withdrawn
Frame windows for small apartments; Explanations
DIN 300 edition 12.1929 → withdrawn
Inlet corners for windows
DIN 300 edition 2.1923 → withdrawn
Inlet corners for windows
DIN 301 - Part 1 · Edition 10.1923 → withdrawn
Semi-countersunk rivets from 10 to 43 mm in diameter
DIN 301 - Part 2 Edition 10.1923 → withdrawn
Semi-countersunk rivets, rivet lengths depending on the grip lengths, construction sheet
DIN 301 - Part 3 · Edition 10.1923 → withdrawn
Semi-countersunk rivets, rivet lengths depending on the grip lengths, construction sheet
DIN 302 · Edition 3.2011 → current
Countersunk rivets · Nominal diameter 10 mm to 36 mm
The standard contains the dimensional specifications and technical delivery conditions for countersunk rivets and specifies their designation.
DIN 302 · Edition 5.1993 → replaced by Edition 3.2011
Countersunk rivets · Nominal diameter 10 to 36 mm
The standard contains the dimensional specifications and technical delivery conditions for countersunk rivets and specifies their designation.
DIN 302 edition 7.1977 → replaced by edition 5.1993
Countersunk rivets · Nominal diameter 10 to 36 mm
DIN 302 - Part 1 · Edition 6.1956 → withdrawn
Countersunk rivets; from 10 to 36 mm in diameter
DIN 302 - Part 1 · Edition 7.1948 → withdrawn
Countersunk rivets from 10 to 36 mm in diameter
This 2nd edition of the standard changed rivets to metric diameters.
DIN 302 - Part 1 edition 11.1921 → withdrawn
Countersunk rivets from 10 to 43 mm in diameter
DIN 302 - Part 2 · Edition 2.1952 → withdrawn
Countersunk rivets for steel construction; The rivet length depends on the clamping length. Set head is countersunk head, locking head is countersunk head
DIN 302 - Part 2 · Edition 10.1923 → withdrawn
Countersunk rivets, rivet lengths depending on the grip lengths, construction sheet
DIN 302 - Part 3 · Edition 2.1952 → withdrawn
Countersunk rivets for boiler construction; The rivet length depends on the clamping length. Set head is countersunk head, locking head is countersunk head
DIN 302 - Part 3 · Edition 10.1923 → withdrawn
Countersunk rivets, rivet lengths depending on the grip lengths, construction sheet
DIN 302 - Part 4 Edition 10.1923 → withdrawn
Countersunk rivets, rivet lengths depending on the grip lengths, construction sheet (closing head for boiler construction)
DIN 302 - Part 5 · Edition 2.1952 → withdrawn
Countersunk rivets for boiler construction; The rivet length depends on the clamping length. The setting head is countersunk head, the closing head is button head
DIN 302 - Part 5 Edition 10.1923 → withdrawn
Countersunk rivets, rivet lengths depending on the grip lengths, construction sheet (closing head for iron construction)
DIN 303 - Part 1 Edition 11.1921 → withdrawn
Raised-head rivets from 10 to 43 mm in diameter
DIN 303 - Part 2 Edition 10.1923 → withdrawn
Raised-head rivets, rivet lengths depending on the grip lengths, construction sheet
DIN 303 - Part 3 Edition 10.1923 → withdrawn
Raised-head rivets, rivet lengths depending on the grip lengths, construction sheet
DIN 303 - Part 4 Edition 10.1923 → withdrawn
Raised-head rivets, rivet lengths depending on the grip lengths (shooting head for boiler construction)
DIN 303 - Part 5 Edition 10.1923 → withdrawn
Raised-head rivets, rivet lengths depending on the grip lengths (shooting head for iron construction)
DIN 304 edition 4.1924 → withdrawn
Disc springs
DIN 305 · Edition 4.1924 → withdrawn
Measuring disc handles
DIN 306 edition 4.1924 → withdrawn
Limit plug gauges, working plug gauges and acceptance plug gauges
DIN 307 edition 1.1928 → withdrawn
Measuring discs with handle
DIN 307 edition 4.1924 → withdrawn
Measuring discs with handle
DIN 308 Edition 4.1924 → withdrawn
Measuring disks
DIN 309 edition 1.1928 → withdrawn
Ball gauges
DIN 309 edition 4.1924 → withdrawn
Ball gauges
DIN 310 · Edition 10.1928 → withdrawn
Measuring rods
DIN 311 Edition 3.1975 → current
Rivet reamers with morse taper shank
DIN 311 edition 10.1954 → withdrawn
Machine tools for metal; Rivet reamers; with morse taper
DIN 311 edition 10.1928 → withdrawn
Rivet reamers with morse taper (compressed air reamers)
DIN 312 edition 8.1931 → withdrawn
Rivet hole reamers with square (cup reamers)
DIN 312 Edition 10.1928 → withdrawn
Rivet hole reamers with square (cup reamers)
DIN 313 edition 1.1956 → withdrawn
Wing nuts 1/4 "to 1"
DIN 313 edition 4.1925 → withdrawn
Wing nuts; 1/4 "to 1"
DIN 314 edition 9.1999 → current
Wing nuts · Edged wing shape
The standard contains the dimensional specifications and technical delivery conditions for wing nuts with an angular wing shape and specifies their designations.
DIN 314 edition 1.1956 → withdrawn
Wing screws 1/4 "to 1"
DIN 314 edition 4.1925 → withdrawn
Wing screws; 1/4 "to 1"
DIN 315 Edition 12.2016 → current
Mechanical fasteners · wing nuts · round wing shape
The standard specifies the requirements for wing nuts with a round wing shape, made of malleable cast iron, steel, austenitic steel and copper-zinc alloy with thread sizes M4 to M24 in product class C.
DIN 315 edition 7.1998 → replaced by edition 12.2016
Wing nuts, round wing shape
The standard contains the dimensional specifications and technical delivery conditions for wing nuts with a round wing shape and specifies their designation.
DIN 315 · Edition 6.1983 → replaced by Edition 7.1998
Wing nuts
DIN 315 · Edition 12.1972 → replaced by Edition 6.1983
Wing nuts
DIN 315 · Edition 1.1956 → withdrawn
Wing nuts M 2 to M 24
DIN 315 · Edition 5.1943 → withdrawn
Wing nuts; M 2 to M 24
DIN 315 edition 4.1925 → withdrawn
Wing nuts, metric thread
DIN 316 Edition 12.2016 → current
Mechanical fasteners - wing bolts - round wing shape
The standard specifies the requirements for wing screws with a round wing shape, made of malleable cast iron, steel, austenitic steel and copper-zinc alloy with thread sizes M4 to M24 in product class C.
DIN 316 edition 7.1998 → replaced by edition 12.2016
Wing screws, round wing shape
The standard contains the dimensional specifications and technical delivery conditions for wing screws with a round wing shape and specifies their designation.
DIN 316 · Edition 6.1983 → replaced by Edition 7.1998
Wing screws
DIN 316 edition 11.1970 → replaced by edition 6.1983
Wing screws
DIN 316 · Edition 1.1956 → withdrawn
Wing screws M 2 to M 24
DIN 316 edition 10.1943 → withdrawn
Wing screws; M 2 to M 24
DIN 316 edition 4.1925 → withdrawn
Wing screws, metric thread
DIN 317 Edition 1.2007 → current
Expeller for taper shafts with expulsion flaps
Drivers according to this standard are used to loosen tools and clamping tools with tapered shanks form B according to DIN 228-1, which are used in machine spindles and clamping tools with tapered sleeves form D according to DIN 228-2.
DIN 317 edition 7.1980 → replaced by edition 1.2007
Expeller for taper shafts with expulsion flaps
DIN 317 edition 10.1965 → withdrawn
Expeller; for taper shanks with drive tabs
DIN 317 edition 2.1943 → withdrawn
Drivers for tool cones according to DIN 228
DIN 317 edition 4.1927 → withdrawn
Drivers for tool cones according to DIN 228
DIN 318 Edition 12.2016 → current
Mechanical fasteners - wing screws - angular wing shape
The standard specifies the requirements for wing screws with angular wing shape, made of malleable cast iron, steel, austenitic steel and copper-zinc alloy with thread sizes M4 to M12 in product class C.
DIN 318 edition 7.1999 → replaced by edition 12.2016
Wing screws · Edged wing shape
The standard contains the dimensional specifications and technical delivery conditions for wing screws with an angular wing shape and specifies their designations.
DIN 319 edition 10.2013 → current
Ball buttons
The standard describes the product requirements for ball knobs that are used for operating handles, for example in machine and plant engineering. It is a correction of the 2.2013 edition
DIN 319 edition 2.2013 → replaced by edition 10.2013
Ball buttons
The standard describes the product requirements for ball knobs that are used for operating handles, for example in machine and plant engineering.
DIN 319 edition 4.2002 → replaced by edition 2.2013
Ball buttons
The standard describes ball knobs that are used for handles in mechanical engineering, on machine tools, devices and apparatus.
DIN 319 edition 10.1962 → withdrawn
Ball buttons
DIN 319 Edition 7.1944 → withdrawn
Ball buttons
DIN 320 · Edition 10.1923 → withdrawn
Center drill for protective countersink
DIN 321 edition 10.1923 → withdrawn
Countersink for center punch hole with protective countersink
DIN 322 Edition 12.1983 → current
Plain Bearings · Loose lubricating rings for general use
DIN 322 edition 11.1970 → replaced by edition 12.1983
Lubricating rings for plain bearings
DIN 322 - Part 2 · Edition 2.1940 → withdrawn
Lubricating rings, slot widths in bearing bushes
DIN 322 U edition 5.1935 (withdrawn 10.1951)
Lubricating rings
Conversion standard
DIN 322 - Part 2 · Edition 7.1927 → withdrawn
Slot widths for lubricating rings in bearing bushes, application sheet
DIN 322 - part 1 edition 8.1922 → withdrawn
Lubricating rings
DIN 323 - Part 1 Edition 8.1974 → current
Standard numbers and series of standard numbers · Main values, exact values, round values
DIN 323 - Part 2 Edition 11.1974 → current
Norm Numbers and Norm Number Series · Introduction
DIN 323 - Part 2 · Edition 8.1959 → withdrawn
Standard numbers; Decimal geometric preferred numbers Explanations, guidelines for use, calculating with standard numbers
DIN 323 - Part 1 · Edition 2.1952x → withdrawn
Standard numbers; Main values, exact values, round values
DIN 323 - Part 1 · Edition 10.1939 → withdrawn
Standardization numbers (decimal geometric series), main values, exact values and round values
DIN 323 - Part 2 Edition 10.1939 → withdrawn
Standardization figures, explanations
DIN 323 edition 1.1922 → withdrawn
Standardization numbers, millimeters
DIN 324 edition 10.1922 → withdrawn
Mortar cone gauges, sleeve, long version, without rag
DIN 325 Edition 10.1922 → withdrawn
Metric taper gauges, sleeve, long version, without tabs
DIN 326 - Part 1 · Edition 6.1981 → withdrawn
Slot cutter with morse taper shank · Dimensions
DIN 326 - Part 2 Edition 1.1990 → 6.2017 withdrawn without replacement
Slot milling cutter with morse taper shank · Technical delivery conditions
The information contained in the technical delivery conditions such as designation, material, dimensions, tolerances, design and labeling apply to slot milling cutters with Morse taper shank according to DIN 326 Part 1.
DIN 326 - part 2 edition 12.1981 → replaced by edition 1.1990
Slot milling cutter with morse taper shank · Technical delivery conditions
DIN 326 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981
Slot milling cutter with morse taper shank · Technical delivery conditions
DIN 326 edition 3.1960 → withdrawn
Slot cutter with morse taper
DIN 326 Edition 7.1927 → withdrawn
Slot milling cutter, with morse taper
DIN 327 - Part 1 · Edition 4.1989 → current
Slot milling cutter with parallel shank · Dimensions
This standard contains information on dimensions and designations for slot milling cutters with straight shank that are intended for general use (K) and those that are primarily intended for precision engineering (KF). Further information such as material, design and labeling are contained in DIN 327 Part 2 Technical Delivery Conditions.
DIN 327 - Part 1 · Edition 9.1978 → replaced by Edition 4.1989
Long hole milling cutter with straight shank, short · Dimensions
DIN 327 - Part 2 · Edition 4.1990 → current
Slot milling cutter with parallel shank · Technical delivery conditions
The information contained in the technical delivery conditions such as designation, dimensions, tolerances, material, design and labeling apply to slot milling cutters with parallel shank in accordance with DIN 327 Part 1.
DIN 327 - Part 2 · Edition 12.1981 → replaced by Edition 4.1990
Slot milling cutter with parallel shank · Technical delivery conditions
DIN 327 - Part 2 · Edition 6.1981 → replaced by Edition 12.1981
Slot milling cutter with parallel shank · Technical delivery conditions
DIN 327 edition 3.1960 → withdrawn
Slot cutter with straight shank
DIN 327 Edition 7.1927 → withdrawn
Slot milling cutter, with straight shank
DIN 328 Edition 7.1927 → 5.1951 withdrawn without replacement
Slot cutter, double-sided
DIN 329 edition 3.1923 → withdrawn
Twist drill with tapered square shaft, long
DIN 330 edition 3.1923 → withdrawn
Twist drill with tapered square shank, short
DIN 331 edition 1.1945 → 4.1955 withdrawn
Spotting drill
(Reason for withdrawal: Instead of the spotting drills according to DIN 331, the short twist drills with parallel shank for automatic machines and turret banks according to DIN 1897 are to be used.)
DIN 331 Edition 3.1924 → withdrawn
Spotting drill
DIN 332 - Part 1 · Edition 4.1986 → current
Center holes 60 °; Form R, A, B and C
The standard applies to centering bores 60 ° without thread, which are used in general mechanical engineering.
DIN 332 - Part 1 edition 11.1973 → replaced by edition 4.1986
Center holes 60 °, form R, A, B and C
DIN 332 - Part 1 · Edition 2.1943 → withdrawn
Center holes, countersink angles 60 ° and 90 °
DIN 332 - Part 2 · Edition 5.1983 → current
Centering holes 60 ° with thread for shaft ends of electrical machines
DIN 332 - Part 2 · Edition 2.1943 → withdrawn
Center holes, with thread, countersunk angle 60 °
DIN 332 - Part 3 · Edition 2.1943 → withdrawn
Centering bores for shaft ends of electric rail vehicles
DIN 332 - Part 4 · Edition 6.1990 → current
Centering bores for wheelset shafts of rail vehicles
The standard applies to wheel set shafts of rail vehicles with wheel set weights of up to 2000 kg.
DIN 332 - Part 4 · Edition 3.1977 → replaced by Edition 6.1990
Centering bores for wheelset shafts of rail vehicles
DIN 332 - Part 4 Edition 7.1964 → withdrawn
Center holes; for axle shafts of rail vehicles
DIN 332 - Part 4 · Edition 4.1946 → withdrawn
Center bores for axles of the Deutsche Reichsbahn
DIN 332 - Part 5 Issue 3.1944 → probably 7.1965 withdrawn
Center holes for gauges, countersink angle 60 °
DIN 332 - Part 7 Edition 9.1982 → current
Machine tools; Center holes 60 °; Determination procedure
DIN 332 - Part 7 edition 11.1977 → replaced by edition 9.1982
Machine tools; Center holes 60 °; Determination procedure
DIN 332 - Part 8 Edition 9.1979 → current
Centering holes 90 °, form S; Dimensions, method of determination
DIN 332 - Part 10 Edition 12.1983 → 11.1997 replaced by DIN ISO 6411
Center holes; Information in technical drawings
DIN 332 edition 9.1922 → withdrawn
Centering holes
DIN 333 edition 4.1986 → current
Center drill 60 °; Form R, A and B
The standard contains information on dimensions, designation, material, design and marking for center drills which are used to produce center bores 60 ° in accordance with DIN 332 Part 1.
DIN 333 edition 11.1973 → replaced by edition 4.1986
Center drill 60 °; Form R, A and B
DIN 333 edition 1.1962 → withdrawn
Center drill 60 °; for center bores form A and R.
DIN 333 edition 3.1943 → withdrawn
Center drill
DIN 333 edition 4.1925 → withdrawn
Center drill
DIN 334 Edition 12.2007 → current
Countersink 60 °
The standard applies to countersinks 60 ° made of high-speed steel, with those with forms A and B mainly used for deburring and those with forms C and D for countersinking.
DIN 334 edition 9.1979 → replaced by edition 12.2007
Countersink 60 °
DIN 334 edition 3.1962 → withdrawn
Countersink 60 °
DIN 334 edition 5.1943 → withdrawn
Countersink 60 °
DIN 334 edition 4.1925 → withdrawn
Countersink 60 °
DIN 335 Edition 12.2007 → current
Countersink 90 °
The standard applies to countersinks 90 ° made of high-speed steel, with those of forms A and B mainly used for deburring and those of forms C and D for countersinking.
DIN 335 edition 9.1979 → replaced by edition 12.2007
Countersink 90 °
DIN 335 edition 8.1962 → withdrawn
Countersink 90 °
DIN 335 edition 5.1943 → withdrawn
Countersink 90 °
DIN 335 edition 4.1925 → withdrawn
Countersink 90 °
DIN 336 Edition 7.2003 → current
Diameter for drill bits for thread core diameters of cut threads
The standard specifies the diameter for drills for cylindrical thread core holes with normal thread length, whereby the drill diameter is approximately equal to the nominal thread diameter minus the pitch. It is not to be used for grooved threads. Drill diameters are specified for the following threads: Metric ISO threads (standard and fine threads), metric EG threads (standard and fine threads), ISO inch threads (UNC and UNF) and pipe threads.
DIN 336 edition 4.1997 → replaced by edition 7.2003
Diameter for drill bits for threaded core holes
The standard contains specifications of the diameters for drilling tools, such as twist drills, reamers, etc., for thread core holes, for metric ISO standard and fine threads, ISO inch threads and pipe threads.
DIN 336 - Part 1 · Edition 4.1969 → replaced by DIN 336 Edition 4.1997
Diameter for drilling tools for threaded core holes; Metric threads
DIN 336 Edition 7.1943 → withdrawn
Drill diameter for thread core holes
Unchanged summary of Part 1 (7.1943) and Part 2 (4.1944)
DIN 336 Edition 7.1926 → withdrawn
Tap drill diameter
DIN 337 edition 3.1923 → 2.1951 withdrawn
Twist drill, short, with straight shank, made of tool steel
replaced by DIN 338
DIN 338 Edition 11.2006 → current
Short twist drills with straight shank
The standard specifies the design, dimensions and tolerances for short twist drills with straight shank made of high-speed steel.
DIN 338 edition 3.1978 → replaced by edition 11.2006
Short twist drills with straight shank
DIN 338 Edition 11.1973 → withdrawn
Short twist drills with straight shank
DIN 338 Edition 3.1923 → withdrawn
Short twist drills with straight shank and driving lugs made of high-speed steel; Construction sheet
DIN 339 edition 11.2006 → current
Twist drill with straight shank for drilling through drill bushes
The standard specifies the dimensions, tolerance, design, designation for twist drills with parallel shank for drilling through drill bushings.
DIN 339 edition 3.1978 → replaced by edition 11.2006
Twist drill with straight shank, for drilling through drill bushes
DIN 339 edition 5.1969 → withdrawn
Twist drill with straight shank; for drilling through drill bushings
DIN 339 edition 3.1923 → withdrawn
Long twist drills with straight shank made of tool steel; Construction sheet
DIN 340 · Edition 11.2006 → current
Long twist drills with straight shank
The standard specifies the design, dimensions and tolerances for long twist drills with straight shank made of high-speed steel.
DIN 340 · Edition 3.1978 → replaced by Edition 11.2006
Long twist drills with straight shank
DIN 340 · Edition 5.1969 → withdrawn
Long twist drills with straight shank
DIN 340 · Edition 3.1923 → withdrawn
Long twist drills with straight shank and driving lugs made of high-speed steel; Construction sheet
DIN 341 edition 11.2006 → current
Long twist drills with Morse taper shank for drilling through drill bushings
The standard specifies the design, dimensions and tolerances for twist drills with Morse taper shank for drilling through drill bushes made of high-speed steel.
DIN 341 edition 3.1978 → replaced by edition 11.2006
Long twist drills with Morse taper shank, for drilling through drill bushes
DIN 341 edition 5.1969 → withdrawn
Long twist drills with Morse taper; for drilling through drill bushings
DIN 341 edition 3.1923 → withdrawn
Twist drill with Morse taper made of tool steel
DIN 342 edition 9.1932 → withdrawn
Countersinks and countersinks, undersized
DIN 342 Edition 7.1926 → withdrawn
Undersize for spiral countersinks and countersinks
DIN 343 Edition 10.1981 → current
Reamers with Morse taper shank
DIN 343 edition 8.1971 → withdrawn
Counterbore (spiral countersink) with morse taper; made of high speed steel
DIN 343 edition 3.1923 → withdrawn
Countersink with taper shank
DIN 344 edition 10.1981 → current
Reamers with straight shank
DIN 344 edition 8.1971 → withdrawn
Countersink with straight shank; made of high speed steel
DIN 344 edition 3.1923 → withdrawn
Spiral countersink with straight shank
DIN 345 edition 11.2006 → current
Twist drill with Morse taper shank
The standard specifies the design, dimensions and tolerances for twist drills with Morse taper shank made of high-speed steel.
DIN 345 edition 3.1978 → replaced by edition 11.2006
Twist drill with Morse taper shank
DIN 345 edition 2.1961 → withdrawn
Twist drill with morse taper
DIN 345 edition 12.1923 → withdrawn
Twist drill with Morse taper made of high-speed steel; Construction sheet
DIN 346 edition 11.2006 → current
Twist drill with larger morse taper shank
The standard specifies the dimensions for twist drills made of high-speed steel with a larger Morse taper shank.
DIN 346 edition 3.1978 → replaced by edition 11.2006
Twist drill with larger morse taper shank
DIN 346 edition 2.1961 → withdrawn
Twist drill with larger morse taper
DIN 346 edition 12.1923 → withdrawn
Twist drill, with stronger morse taper, made of high speed steel
DIN 347 Edition 3.1962 → current
Countersink 120 °
DIN 347 edition 5.1943 → withdrawn
Countersink 120 °
DIN 347 edition 4.1925 → withdrawn
Countersink 120 °
DIN 348 edition 9.1922 → withdrawn
Countersink 30 ° for countersunk countersunk screws
DIN 349 edition 3.1923 → withdrawn
Lyre drill with tapered square shaft, construction sheet
DIN 350 Edition 3.1923 → withdrawn
Lyre drill with flattened cylindrical shank, construction sheet
DIN 351 Edition 5.1951 → replaced by DIN 31856 - Part 1
Machine tools for metal; Set of taps, three-part set, Whitworth threads 1/16 "to 3"
DIN 351 3rd edition 10.1947 → withdrawn
Machine tools for metal; Set of taps, dimensions, Whitworth thread 1/16 "to 2"
Labeling and designations new, I 1 , I 2 , d 1 partially changed.
DIN 351 edition 3.1923 → withdrawn
Hand taps for Whitworth thread according to DIN 11
DIN 352 Edition 1.2016 → current
Set of taps - three-part set for metric ISO standard threads M 1 to M 68
DIN 352 edition 11.2008 → replaced by edition 1.2016
Set of taps - three-part set for metric ISO standard threads M 1 to M 68
DIN 352 edition 9.1998 → replaced by edition 11.2008
Set of taps - three-part set for metric ISO standard threads M 1 to M 68
DIN 352 edition 6.1981 → replaced by edition 9.1998
Set of taps; Three-part set for metric ISO standard threads M 1 to M 68
DIN 352 edition 8.1971 → withdrawn
Set of taps, three-part set for metric ISO standard threads from M 1 to M 68
DIN 352 Edition 5.1951 → replaced by DIN 31856 - Part 1
Machine tools for metal; Set of taps, three-part set, metric thread M 1 to M 68
DIN 352 - Part 1 Edition 10.1944 → withdrawn
Set of taps, metric thread M 1 to M 68
DIN 352 - Part 2 Edition 10.1944 → withdrawn
Set of taps, metric fine thread with pitches 0.2 to 3 mm
DIN 352 Edition 3.1923 → withdrawn
DIN 353 Edition 5.1954 → 7.1985 replaced by DIN 5157
Machine tools for metal; Set of taps, two-part; Whitworth pipe thread R 1/8 "to R 4"
DIN 353 edition 12.1944 → withdrawn
Set of taps, Whitworth pipe thread R 1/8 "to R 4"
DIN 353 Edition 3.1923 → withdrawn
DIN 354 edition 3.1923 → withdrawn
Nut taps with short shank for Whitworth thread according to DIN 11
DIN 355 edition 3.1923 → withdrawn
Nut taps for metric threads according to DIN 13 and 14
DIN 356 edition 5.1951x → withdrawn without replacement
Machine tools for metal; Nut taps; Whitworth thread 1/8 "to 3"
DIN 356 edition 3.1923 → withdrawn
Nut taps with long shank for Whitworth threads
DIN 357 edition 2.2016 → current
Nut taps for metric ISO standard threads M 3 to M 68
The standard applies to taps for the production of nuts with metric ISO standard thread according to DIN 13-1.
DIN 357 edition 11.2008 → replaced by edition 2.2016
Nut taps for metric ISO standard threads M 3 to M 68
DIN 357 edition 7.1998 → replaced by edition 11.2008
Nut taps for metric ISO standard threads M 3 to M 68
DIN 357 · Edition 6.1981 → replaced by Edition 7.1998
Nut taps for metric ISO standard threads M 3 to M 68
DIN 357 edition 8.1971 → withdrawn
Nut taps for metric ISO standard threads from M 3 to M 68
DIN 357 edition 3.1923 → withdrawn
Nut taps with long shank for metric threads
DIN 358 edition 12.1923 → withdrawn
Die taps for Whitworth threads
DIN 359 edition 12.1923 → withdrawn
Die taps for metric threads
DIN 360 · Edition 12.1923 → withdrawn
Die taps for Whitworth pipe threads
DIN 361 edition 3.1923 → withdrawn
Hand jaw taps for Whitworth threads
DIN 362 edition 3.1923 → withdrawn
Hand-jaw taps for metric threads
DIN 363 Edition 3.1923 → withdrawn
Hand-jaw taps for Whitworth pipe threads
DIN 364 edition 11.1921 → 2.1951 withdrawn
NA pipes, normal drainage pipes
DIN 365 · Edition 4.1928 → withdrawn
Twist drills, countersinks and countersinks, ground round, manufacturing accuracy
DIN 366 edition 11.1931 → 11.1969 presumably withdrawn without replacement
Plates for form gauges, guidelines for external dimensions, tools
DIN 367 edition 1.1930 → withdrawn
Hand drills, connection thread for the drill chuck shank
DIN 368 Edition 3.1935 → withdrawn
Special thread with Whitworth shape for closures, theoretical values
DIN 368 Edition 10.1928 → withdrawn
Special thread with Whitworth shape for closures, 2 1/4 threads on 1 ", theoretical values
DIN 369 edition 7.1928 → withdrawn
Setting rings for reamers
DIN 369 edition 4.1925 → withdrawn
Setting rings for reamers
DIN 370 Edition 7.1940 → withdrawn
Countersink for cheese head screws with Whitworth thread
DIN 371 edition 1.2016 → current
Machine taps with reinforced shank for metric ISO standard threads M1 to M10 and metric ISO fine threads M1 × 0.2 to M10 × 1.25
The standard applies to machine taps with reinforced shank, which are intended for the production of metric ISO standard threads according to DIN 13 part 1 and metric ISO fine threads according to DIN 13 parts 2 to 5.
DIN 371 edition 11.2008 → replaced by edition 1.2016
Machine taps with reinforced shank for metric ISO standard threads M 1 to M 10 and metric ISO fine threads M 1x0.2 to M 10x1.25
The standard applies to machine taps with reinforced shank for the production of ISO metric coarse threads and ISO metric fine threads.
DIN 371 edition 7.1998 → replaced by edition 11.2008
Machine taps with reinforced shank for metric ISO standard threads M 1 to M 10 and metric ISO fine threads M 1x0.2 to M 10x1.25
DIN 371 · Edition 6.1981 → replaced by Edition 7.1998
Machine taps with reinforced shank, for metric ISO standard threads M 1 to M 10
DIN 371 edition 8.1971 → withdrawn
Machine taps with reinforced shank for metric ISO standard threads from M 1 to M 10
DIN 372 edition 7.1940 → replaced by DIN 373 and DIN 375, editions 12.1962
Tools, neck counters, for screws with Whitworth thread according to DIN 11
DIN 373 Edition 12.2007 → current
Countersink with straight shank and fixed guide pin
The standard specifies the dimensions for countersinks with straight shank and fixed guide pin made of high-speed steel.
DIN 373 edition 8.1975 → replaced by edition 12.2007
Countersink with straight shank and fixed guide pin
DIN 373 Edition 10.1969 → withdrawn
Countersink with straight shank and fixed guide pin
DIN 373 edition 12.1962 → withdrawn
Countersink with straight shank and fixed guide pin
extended, sizes of the Halssenker (previously DIN 372) incorporated. Together with DIN 375 replacement for DIN 372.
DIN 373 Edition 7.1940 → withdrawn
Countersink for cylinder head screws with metric thread
DIN 374 Edition 1.2016 → current
Machine taps with stepped shank (overflow drill) for ISO metric fine threads M3 × 0.2 to M52 × 4
The standard applies to machine taps with a stepped shank (overflow drill) for the production of metric ISO fine threads according to DIN 13 parts 2 to 9.
DIN 374 edition 11.2008 → replaced by edition 1.2016
Machine taps with stepped shank (overflow drill) for metric ISO fine threads M 3x0.2 to M 52x4
The standard applies to machine taps (overflow drills) for the production of metric ISO fine threads according to DIN 13 parts 2 to 9.
DIN 374 edition 7.1998 → replaced by edition 11.2008
Machine taps (overflow drill) for metric ISO fine threads M 3 × 0.2 to M 52 × 4
DIN 374 · Edition 6.1981 → replaced by Edition 7.1998
Machine taps (overflow drill), for metric ISO fine threads M 1.6 to M 52
DIN 374 edition 8.1971 → withdrawn
Machine taps (overflow drill) for metric ISO fine threads from M 1.6 to M 52
DIN 375 Edition 12.2007 → current
Countersink with Morse taper shank and exchangeable guide pin
The standard specifies the dimensions for countersinks with Morse taper shank and exchangeable guide pins made of high-speed steel.
DIN 375 edition 8.1975 → replaced by edition 12.2007
Countersink with Morse taper shank and exchangeable guide pin
DIN 375 edition 10.1969 → withdrawn
Countersink with Morse taper and exchangeable guide pin
Editorial revised, abbreviations and application examples for countersinks adapted to DIN 74.
DIN 375 edition 12.1962 → withdrawn
Countersink with Morse taper and exchangeable guide pin
extended, sizes of the Halssenker (previously DIN 372) incorporated. Together with DIN 373 replacement for DIN 372.
DIN 375 Edition 7.1940 → withdrawn
Neck countersink for screws with metric thread
DIN 376 edition 2.2016 → current
Machine taps with stepped shank (overflow drill) for metric ISO standard threads M1.6 to M68
The standard applies to machine taps with a stepped shank (overflow drill) for the production of metric ISO standard threads according to DIN 13 Part 1.
DIN 376 edition 11.2008 → replaced by edition 2.2016
Machine taps with stepped shank (overflow drill) for metric ISO standard threads M 3 to M 68
The standard applies to machine taps (overflow drills) for the production of metric ISO standard threads according to DIN 13 Part 1.
DIN 376 edition 7.1998 → replaced by edition 11.2008
Machine taps (overflow drill) for metric ISO standard threads M 3 to M 68
DIN 376 · Edition 6.1981 → replaced by Edition 7.1998
Machine tap (overflow drill), for metric ISO standard threads M 1.6 to M 68
DIN 376 edition 8.1971 → withdrawn
Machine taps (overflow drill) for metric ISO standard threads from M 1.6 to M 68
DIN 376 - Part 1 Edition 10.1943x → withdrawn
Machine taps, straight taps with reinforced shank for metric threads and metric fine threads, thread diameter 1 to 12 mm
DIN 376 - Part 2 Edition 10.1943x → withdrawn
Machine taps, straight taps (overflow drill) for metric threads M 1.7 to M 68
DIN 376 - Part 3 Edition 11.1943x → withdrawn
Machine taps, straight taps for metric fine threads with pitches h 0.2 to 3 mm, thread diameter 1.7 to 52 mm
DIN 377 edition 5.2000 → current
Extender for tools with square according to DIN 10
The extenders according to this standard are intended for hand-operated and machine-operated tools unless there are special requirements for concentricity.
DIN 377 edition 8.1969 → replaced by edition 5.2000
Extender for tools with square
Extender for ISO square.
DIN 377 edition 9.1943 → 10.1966 withdrawn
Extender for tools with square
DIN 377 Edition 7.1926 → withdrawn
Extender for taps
DIN 378 - Part 1 Edition 10.1925x → withdrawn
Trapezoidal thread, fine, catchy from 10 to 195 mm in diameter
DIN 378 - Part 2 Edition 10.1925x → withdrawn
Trapezoidal thread, fine, catchy from 200 to 640 mm in diameter
DIN 378 - Part 1 Edition 10.1925 → withdrawn
Trapezoidal thread, fine, catchy from 10 to 195 mm in diameter
DIN 378 - Part 2 Edition 10.1925 → withdrawn
Trapezoidal thread, fine, catchy from 200 to 640 mm in diameter
DIN 379 edition 8.1937 → withdrawn
Trapezoidal thread, coarse
DIN 379 edition 10.1925 → withdrawn
Trapezoidal thread, coarse, catchy
DIN 380 - Part 1 · Edition 4.1985 → current
Flat Metric Trapezoidal Thread · Thread Profiles
The standard specifies the dimensions of the thread profiles for flat metric trapezoidal threads.
DIN 380 - Part 2 · Edition 4.1985 → current
Flat Metric Trapezoidal Thread · Series of threads
This standard contains flat metric trapezoidal threads with profiles according to DIN 380 Part 1.
DIN 381 edition 5.1943 → withdrawn
Countersink 75 °
DIN 381 edition 4.1930 → withdrawn
Countersink 75 °
DIN 382 Edition 12.2009 → current
Hexagonal dies
The standard contains information on dimensions, designation, material, design and marking for hexagonal dies made of high-speed steel, which are used for cutting metric ISO standard threads according to DIN 13 Part 1, metric ISO fine threads according to DIN 13 Part 2 to Part 9, cylindrical pipe thread according to DIN ISO 228 Part 1 and tapered pipe thread according to DIN 2999 Part 1.
DIN 382 edition 12.1987 → replaced by edition 12.2009
Hexagonal dies
DIN 382 edition 2.1943 → replaced by edition 12.1987
Hexagonal re-cutting dies
DIN 383 Edition 7.1928 → withdrawn
Driving wedges, insertion wedges, nose wedges for lightly stressed transmission parts (dwarf wedges)
DIN 384 edition 2.1934 → withdrawn
Bearing bushes, with white metal spout, main dimensions
DIN 384 Edition 7.1926 → withdrawn
Bearing bushes for white metal spout, construction sheet
DIN 385 edition 10.1940 → withdrawn
Curves, bevels, ring grooves for bearing bushes
DIN 385 Edition 7.1926 → withdrawn
Curves, bevels, ring grooves for bearing bushes
DIN 388 - Part 1 · Edition 1.1996 → current
Hand wheels made of plastic; with corrugated rim
The specifications contained in this standard apply to handwheels with a shaft rim made of molded material according to DIN 7708 with a square according to DIN 79.
DIN 388 - Part 1 · Edition 2.1972 → replaced by Edition 1.1996
Handwheels made of plastic, with corrugated rim
DIN 388 - Part 2 Edition 2.1972 → 2.2003 withdrawn without replacement
Hand wheels made of plastic; with knurled ring
DIN 388 - Part 1 · Edition 1.1938 → withdrawn
Handwheels, made of molded material
DIN 388 - Part 2 · Edition 1.1938 → withdrawn
Handwheels, made of molded material
DIN 388 Edition 4.1924 → withdrawn
Handwheels made of heat protection compound
DIN 389 edition 4.1924 → withdrawn
Handwheels, with corrugated rim and straight arms
DIN 390 Edition 4.2002 → current
Handwheels, cranked · Hub holes with straight square
The standard describes handwheels that are mainly used for fittings that are manufactured with square edges for spindles according to DIN 79.
DIN 390 edition 4.1973 → replaced by edition 4.2002
Handwheels, cranked · Straight square hub hole, mainly for fittings
DIN 390 Edition 3.1954 → withdrawn
Handwheels; with corrugated rim and sloping arms
DIN 390 edition 4.1924 → withdrawn
Handwheels, with corrugated rim and sloping arms
DIN 395 Edition 12.1968 → current
File handles
DIN 395 edition 4.1933 → withdrawn
File handles
DIN 395 edition 4.1927 → withdrawn
File handles
DIN 396 edition 12.1968 → current
Forceps for tool handles
DIN 396 edition 4.1927 → withdrawn
Forceps for handles
DIN 398 · Edition 6.1976 → withdrawn
Hüttensteine · Solid stones, perforated stones, hollow blocks
DIN 398 Edition 7.1965 → withdrawn
Hüttensteine · Solid and perforated stones
DIN 398 Edition 10.1941 → withdrawn
Hüttensteine (masonry stones)
DIN 399 suppl. · Edition 5.1943 → replaced by DIN 4156 edition 5.1943
DIN 399 edition 10.1941 → replaced by DIN 18152 edition 9.1952
Hut floating stones
DIN 400 suppl. · Edition 5.1943 → replaced by DIN 4156 edition 5.1943
DIN 400 edition 10.1941 → replaced by DIN 18152 edition 9.1952
Cinder blocks
DIN 401 edition 2.1923 → withdrawn
Mortise tapes for cabinet doors and windows
DIN 402 edition 2.1923 → withdrawn
Mortise hinges for doors
DIN 403 edition 1.1973 → current
Knurling wheels
DIN 403 Edition 7.1926 → withdrawn
Knurling wheels, cord wheels
DIN 404 - Correction 1 · Edition 6.2007 → current
Cross-hole screws with slot
Corrections to edition 8.2006
DIN 404 edition 8.2006 → current
Cross-hole screws with slot
The standard specifies the properties of cross-hole screws with a slot for threads from M 2 to M 10.
DIN 404 edition 9.1986 → replaced by edition 8.2006
Cross-hole screws
The standard contains the dimensional specifications and technical delivery conditions for cross-hole screws and specifies their designation.
DIN 404 edition 2.1972 → replaced by edition 9.1986
Cross-hole screws with slot
DIN 404 · Edition 6.1953 → withdrawn
Cross-hole screws, metric thread
DIN 404 Edition 10.1942 → withdrawn
Cross-hole screws M 1 to M 10
DIN 404 Edition 2.1923 → withdrawn
Cross-hole screws from M 1 to M 10
DIN 405 - Part 1 · Edition 11.1997 → current
General purpose round threads · Thread profiles, nominal dimensions
The standard specifies the thread profiles and nominal dimensions for external and internal threads.
DIN 405 - Part 2 Edition 11.1997 → current
General purpose round threads · Dimensions and tolerances
The standard defines dimensions and tolerances.
DIN 405 - Part 3 · Edition 11.1997 → current
General purpose round threads · Gauges for external and internal threads; Types of gauges, profiles, tolerances
The standard specifies a gauge system for the round thread according to DIN 405 - Part 1.
DIN 405 - Part 2 Edition 10.1981 → replaced by Edition 11.1997
General purpose round threads · Dimensions and tolerances
The standard defines dimensions and tolerances.
DIN 405 - Part 1 Edition 11.1975 → replaced by Edition 11.1997 and DIN 405 Part 2
General purpose round threads · Thread profiles, nominal dimensions
DIN 405 edition 4.1928 → withdrawn
Round thread
DIN 405 edition 4.1922 → withdrawn
Round thread
DIN 406 - Part 10 · Edition 12.1992 → current
Technical drawings · Entry of dimensions · Terms, general principles
The standard defines the general basis for dimension entries in technical drawings, including technical documents. It contains the terms and their explanations relevant to the measurement, the graphic symbols and symbols used in connection with the measurement, as well as a description of the essential systems of the measurement. The connection to DIN 406 Part 11 is established by some basic application rules.
DIN 406 - Part 11, supplement 1 edition 12.2000 → current
Technical drawings · Entry of dimensions · Basics and application · Outcome of machining on raw parts
The supplement contains information about the entry of dimensions for the first machining of raw parts with the help of reference dimensions or shape and position tolerances. The two methods are explained using examples and their combinability is presented.
DIN 406 - Part 11 Edition 12.1992 → current
Technical drawings · Entry of dimensions · Basics of application
The standard specifies the basic rules of dimensioning applicable to all branches of industry. These rules concern the elements of the dimension entry and the entry of dimensions for all frequently occurring form elements. In addition, the standard contains specifications for special types of dimensions and for the types of dimensions that are possible in principle.
DIN 406 - Part 12 Edition 12.1992 → current
Technical drawings · Entry of dimensions · Entry of tolerances for length and angle dimensions; ISO 406 edition 1987, modified
The standard defines the general rules for entering tolerances for length and angle dimensions. The various options for specifying tolerances for individual parts and for parts shown together are dealt with.
DIN 406 - part 1 edition 4.1977 → replaced by DIN 406 part 10 edition 12.1992
Entry of dimensions in drawings, types
DIN 406 - Part 1 Edition 12.1922 → withdrawn
Drawings · Entry of dimensions, distribution of dimensions
DIN 406 - Part 2 edition 8.1981 → replaced by DIN 406 parts 10, 11 and 12 each edition 12.1992
Entry of dimensions in drawings · Rules
DIN 406 - Part 2 · Edition 4.1980 → replaced by Edition 8.1981
Entry of dimensions in drawings · Rules
DIN 406 - Part 2 · Edition 6.1968 → withdrawn
Entry of dimensions in drawings · Rules
DIN 406 - Part 2 Edition 12.1922 → withdrawn
Drawings · Dimensions, dimension lines
DIN 406 - Part 3 Supplement 1 Edition 4.1985 → 2.1987 withdrawn without replacement
Entering dimensions in drawings · Dimensioning using coordinates; Bolt circle coordinates
DIN 406 - Part 3 Supplement 1 Edition 10.1978 → replaced by Edition 4.1985
Entering dimensions in drawings · Dimensioning using coordinates; Bolt circle coordinates
DIN 406 - Part 3 Edition 7.1975 → replaced by DIN 406-11 Edition 12.1992
Entering dimensions in drawings · Dimensioning using coordinates
DIN 406 - Part 3 Edition 12.1922 → withdrawn
Drawings · Dimension entries, dimension arrows, dimension figures
DIN 406 - Part 4 Edition 12.1980 → 12.1993 withdrawn without replacement
Entry of dimensions in drawings · Dimensions for machine programming
DIN 406 - Part 4 Supplement 1 Edition 12.1980 → 12.1993 withdrawn without replacement
Entry of dimensions in drawings · Dimensions for machine programming, application example
DIN 406 - part 4 edition 5.1937 → withdrawn
Drawings · Entry of dimensions · Cones etc., dimensional changes, partial symbols, threads
DIN 406 - Part 4 Edition 12.1922 → withdrawn
Entry of dimensions · cones etc., dimensional changes, part numbers, threads
DIN 406 - Part 5 Edition 10.1941 → withdrawn
Drawings · Entry of dimensions, entry of tolerances through dimensions
DIN 406 - Part 5 Edition 11.1924 → withdrawn
Dimensions, tolerances, fits
DIN 406 - Part 6 Edition 10.1941 → withdrawn
Drawings · Entry of dimensions, entry of tolerances using fitting symbols
DIN 406 - Part 6 Edition 1.1926 → withdrawn
Dimensions, tolerances, fits
DIN 407 - Part 1 Edition 7.1959 → withdrawn
Symbols for rivets, screws and hole diameters; in steel structures
DIN 407 - Part 1 Edition 10.1951xx → withdrawn
Symbols for rivets and screws in steel structures
DIN 407 - Part 2 · Edition 1.1955 → withdrawn
Symbols for rivets and screws; Through and threaded holes, preferably for machine and locomotive construction.
DIN 407 edition 10.1951x → withdrawn
Symbols for rivets and screws in steel structures
DIN 407 Edition 7.1948 → withdrawn
Symbols for rivets and screws in steel structures
This 2nd edition of the standard has been completely revised.
DIN 407 edition 4.1928 → withdrawn
Symbols for rivets and screws in iron structures
1st edition of the standard. This standard used to be DIN 139.
DIN 408 edition 2.1923 → withdrawn
Attachment tapes for windows and doors
DIN 409 · Edition 5.1938 → withdrawn
Tiles for clay ovens, square
DIN 409 edition 10.1925 → withdrawn
Tiles for clay ovens, square
DIN 410 · Edition 10.1923 → withdrawn
Bare studs for 1 nut or 1 castle nut 1 d from 1/4 "to 2", screw-in end 1 d
DIN 411 edition 10.1923 → withdrawn
Bare studs for 1 nut or 1 castle nut 1 d from 1/4 "to 2", screw-in end 1.3 d
DIN 412 edition 10.1923 → withdrawn
Bare studs for 1 nut or 1 castle nut 1 d from 1/4 "to 2", screw-in end 2.5 d
DIN 413 edition 10.1923 → withdrawn
Bare studs for 2 nuts 1 d from 1/4 "to 2", screw-in end 1 d
DIN 414 edition 10.1923 → withdrawn
Bare studs for 2 nuts 1 d from 1/4 "to 2", screw-in end 1.3 d
DIN 415 edition 10.1923 → withdrawn
Bare studs for 2 nuts 1 d from 1/4 "to 2", screw-in end 2.5 d
DIN 416 edition 4.1926x → withdrawn
Threaded pins; with spigot, 1/2 "to 3/4"
DIN 416 edition 4.1926 → withdrawn
Grub screws with tenons, Whitworth thread
DIN 416 edition 10.1923 → withdrawn
Grub screws with tenons, Whitworth thread
DIN 417 edition 9.1986 → 10.1992 replaced by DIN EN 27435
Grub screws with slot and tenon; ISO 7435, 1983 edition modified
DIN 417 edition 2.1972 → replaced by edition 9.1986
Grub screws with slot and tenon
DIN 417 edition 6.1938x → withdrawn
Threaded pins; with pin, M 2 to M 20
DIN 417 edition 10.1923 → withdrawn
Grub screws with tenons, metric thread
DIN 418 - Supplement · Edition 10.1926 → withdrawn
to DIN 418, weights
DIN 418 edition 4.1925 → withdrawn
Hexagon bolts with hexagon nut
DIN 419 edition 12.1920 → withdrawn
Bare, low hex nuts, Whitworth threads
DIN 420 edition 10.1923 → 1.1931 withdrawn
Bare studs for 1 nut or 1 castle nut 1 d from M 3 to M 52, screw-in end 1 d
DIN 421 edition 10.1923 → 1.1931 withdrawn
Bare stud bolts for 1 nut or 1 castle nut 1 d from M 3 to M 52, screw-in end 1.3 d
DIN 422 edition 10.1923 → 1.1931 withdrawn
Bare studs for 1 nut or 1 castle nut 1 d from M 3 to M 52, screw-in end 2.5 d
DIN 423 edition 8.1921 → 1.1931 withdrawn
Bare studs for 2 nuts or 1 castle nut for screwing into steel, cast steel, bronze; Screw-in end 1 d metr. thread
DIN 424 edition 8.1921 → 1.1931 withdrawn
Bare stud bolts for 2 nuts or 1 castle nut for screwing into cast iron; Screw-in end 1.3 d metr. thread
DIN 425 edition 10.1924 → 1.1931 withdrawn
Bare stud bolts for 2 nuts or 1 castle nut for screwing into soft metal; Screw-in end 2.5 d metr. thread
DIN 425 edition 10.1923 → withdrawn
Bare studs for 2 nuts 1 d from M 3 to M 52, screw-in end 2.5 d
DIN 426 edition 4.1926x → withdrawn
Set screws; 1/2 "to 3/4"
DIN 426 edition 4.1926 → withdrawn
Grub screws, set screws, Whitworth threads
DIN 426 edition 10.1922 → withdrawn
Shaft bolts, Whitworth thread
DIN 427 edition 9.1986 → replaced by DIN EN ISO 2342 edition 5.2004
Shank screws with slot and tapered point
The standard contains the dimensional specifications and technical delivery conditions for headless screws with slot and tapered point and specifies their designation.
DIN 427 edition 2.1972 → withdrawn
Shank screws with slot and tapered point
DIN 427 · 5th edition 1.1951 → withdrawn
Set screws M 1 to M 20, M 18 × 2 and M 20 × 2
Thread M 18 × 2 and M 20 × 2 added. Top dimension z included in length l. Thread length b changed.
DIN 427 · 4th edition 1.1949 → withdrawn
Set screws M 1 to M 20
Special sizes for weighing scales added
DIN 427 edition 10.1922 → withdrawn
Grub screws, shaft screws, metric thread
DIN 428 edition 7.1925 → 1.1931 withdrawn
Raw hex nuts, height about 1 d
DIN 429 edition 12.1921 → withdrawn
Bare, low hex nuts, metric thread
DIN 430 edition 12.1923 → 1.1931 withdrawn
Raw hex nuts, castle nuts, hex height about 1 d
DIN 430 - Supplement · Edition 12.1923 → replaced by DIN 533 Part 2 Edition 4.1934x
DIN 431 edition 5.2013 → current
Pipe nuts with pipe thread according to DIN EN ISO 228-1
The standard specifies requirements for hexagon and octagon pipe nuts with pipe thread according to DIN EN ISO 228-1 with thread sizes from G 1/8 to G 6 in product classes B and C.
DIN 431 edition 10.2000 → replaced by edition 5.2013
Pipe nuts with pipe thread according to DIN ISO 228 Part 1
The standard specifies requirements for pipe nuts with pipe thread according to DIN ISO 288-1 from nominal size G 1/8 to G 6 in product classes B and C.
DIN 431 edition 2.2000 → replaced by edition 10.2000
Pipe nuts with pipe thread according to DIN ISO 228 Part 1
DIN 431 edition 11.1982 → replaced by edition 2.2000
Pipe nuts with pipe thread according to DIN ISO 228 Part 1
DIN 431 edition 12.1972 → replaced by edition 11.1982
Pipe nuts; Whitworth pipe threads
DIN 431 · Edition 6.1949 → withdrawn
Hexagonal pipe nuts; R 1/8 "to R 6"
DIN 431 edition 4.1929 → withdrawn
Raw and half raw hex tube nuts, Whitworth tube threads
2nd edition of the standard
DIN 431 edition 1.1926 → replaced by edition 4.1929
Raw and half raw hex tube nuts, Whitworth tube threads
1st edition of the standard
DIN 432 edition 11.1983 → 5.2003 withdrawn without replacement
Washers with outside nose (locking plates with nose)
DIN 432 edition 2.1954 → withdrawn
Locking plates; with nose
DIN 432 · Edition 5.1943 → withdrawn
Lock washers with nose
DIN 432 · Edition 4.1927 → withdrawn
Lock washers with nose
DIN 432 - Part 1 · Edition 10.1921 → withdrawn
Lock washers with nose
DIN 433 Part 1 Issue 3.1990 → withdrawn
Discs; Product class A up to hardness 250 HV, preferably for cylinder screws
DIN 433 Part 2 Issue 3.1990 → withdrawn
Discs; Product class A from hardness 300 HV, preferably for cylinder screws
DIN 433 edition 3.1972 → withdrawn
Discs; preferably for cylinder screws
DIN 433 edition 4.1946 → withdrawn
Washers for button-head cylinder screws and bolts
DIN 433 edition 3.1923 → withdrawn
Semi-bright washers for cylinder head screws and button-head screws
DIN 434 · Edition 4.2000 → current
Washers, square, wedge-shaped for U-beams
The standard specifies the properties of wedge-shaped square washers for U-beams.
DIN 434 edition 1.2000 → replaced by edition 4.2000
Washers, square, wedge-shaped for U-beams
DIN 434 edition 4.1990 → replaced by edition 1.2000
Washers, square, wedge-shaped for U-beams
DIN 434 edition 2.1990 → replaced by edition 4.1990
Washers, square, wedge-shaped for U-beams
DIN 434 edition 11.1970 → replaced by edition 2.1990
Washers, square, for U-beams
DIN 434 · Edition 5.1943 → withdrawn
Square washers for U and I beams
DIN 434 · Edition 4.1924 → withdrawn
Square washers for U-beams
DIN 435 edition 1.2000 → current
Washers, square, wedge-shaped for I-beams
The standard specifies the properties of wedge-shaped square washers for I-beams.
DIN 435 edition 12.1989 → replaced by edition 1.2000
Washers, square, wedge-shaped for I-beams
DIN 435 edition 11.1970 → replaced by edition 12.1989
Washers, square, for I-beams
DIN 435 · Edition 5.1943 → withdrawn
Square washers for U and I beams
DIN 435 · Edition 4.1924 → withdrawn
Square I-washers for I-beams
DIN 436 · Edition 5.1990 → current
Washers, square, mainly for wooden constructions
The standard contains the dimensional specifications and technical delivery conditions for square panes, primarily for wooden structures, and specifies their designation.
DIN 436 edition 7.1974 → replaced by edition 5.1990
Washers, square, mainly for wooden constructions
DIN 436 · Edition 5.1943 → withdrawn
Square washers; for wood connections
DIN 436 edition 3.1924 → withdrawn
Square washers for wood connections
DIN 437 edition 4.1925 → withdrawn
Grub screws with cup point, Whitworth thread
DIN 438 Edition 9.1986 → 10.1992 replaced by DIN EN 27436
Grub screws with slot and cup point; ISO 7436, 1983 edition modified
DIN 438 · Edition 2.1972 → replaced by Edition 9.1986
Grub screws with slot and cup point (M 3 to M 10)
DIN 438 edition 1.1951 → withdrawn
Grub screws with cup point, M3 to M 10
DIN 438 · Edition 5.1924 → withdrawn
Grub screws with cup point, metric thread
DIN 439 - Part 1 Edition 10.1987 → 2.1992 replaced by DIN EN 24036
Low hex nuts; Product class B, without bevel
DIN 439 - Part 1 · Edition 12.1983 → replaced by Edition 10.1987 and DIN ISO 4036
Hex nuts, low shape; Thread M 1.6 to M 10; ISO 4036 modified
DIN 439 - Part 2 Edition 10.1987 → 2.1992 replaced by DIN EN 24035 and DIN EN 28675
Low hex nuts; Product classes A and B, with bevel
DIN 439 - Part 2 Edition 12.1983 → replaced by Edition 10.1987, DIN ISO 4035 and DIN ISO 8675
Hex nuts; low shape, thread M 1.6 to M 52 and M 8 × 1 to M 52 × 3; ISO 4035 modified
DIN 439 edition 12.1972 → withdrawn
Hexagon nuts, low shape
DIN 439 edition 9.1941 → withdrawn
Hex nuts; flat, M 1.7 to M 10, version w
DIN 439 edition 4.1925 → withdrawn
Flat hexagon nut, metric thread
DIN 440 · Edition 3.2001 → current
Washers with square hole, mainly for wooden constructions
The standard contains the dimensional specifications and technical delivery conditions for panes with square holes, primarily for wooden structures, and specifies their designation.
DIN 440 edition 5.1990 → replaced by edition 3.2001 and DIN EN ISO 7094 edition 12.2000
Discs, mainly for wooden structures
DIN 440 · Edition 7.1974 → replaced by Edition 5.1990
Discs, mainly for wooden structures
DIN 440 · Edition 5.1943 → withdrawn
(Raw) slices; for wood connections
DIN 441 edition 12.1919 → withdrawn
Three-pane, simple window without transom (narrow, low panes)
DIN 442 Edition 1.2011 → current
Closing cover for rolling in
The standard specifies requirements for sealing lids with a diameter of 10 mm to 100 mm.
DIN 442 edition 11.1970 → replaced by edition 1.2011
Closing cover for rolling in
DIN 442 · Edition 6.1946 → withdrawn
Closing cover for rolling in
DIN 442 edition 12.1919 → withdrawn
Three-pane, double window without transom (narrow, low panes)
DIN 443 · Edition 6.2011 → current
Sealing cover for pushing in
The standard specifies requirements for sealing lids with a diameter of 8 mm to 63 mm.
DIN 443 edition 1.2011 → replaced by edition 6.2011
Sealing cover for pushing in
The standard specifies requirements for sealing lids with a diameter of 8 mm to 63 mm.
DIN 443 edition 11.1970 → replaced by edition 1.2011
Closing cover to press in
DIN 443 edition 6.1946 → withdrawn
Closing cover to press in
DIN 443 edition 12.1919 → withdrawn
Three-pane, simple window with transom (narrow, high panes)
DIN 444 Edition 4.2017 → current
Mechanical fasteners · Eye bolts
The standard specifies the designation, dimensions, tolerances and technical delivery conditions for eye bolts with metric threads M5 to M39.
DIN 444 edition 4.1983 → replaced by edition 4.2017
Eye bolts
DIN 444 edition 10.1981 → replaced by edition 4.1983
Eye bolts
DIN 444 edition 1.1971 → withdrawn
Eye bolts
DIN 444 - Part 1 · Edition 4.1942 → withdrawn
Eye bolts (hinged bolts); M 5 to M 39
DIN 444 - Part 2 Edition 10.1937x → withdrawn
Eye bolts (hinged bolts); 1/2 "to 1 1/2"
DIN 444 edition 12.1919 → withdrawn
Three-pane, double window with transom (narrow, high panes)
DIN 445 edition 1.1927 → withdrawn
Standard thread plug gauges for Whitworth threads
DIN 446 edition 1.1927 → withdrawn
Standard thread plug gauges for metric threads
DIN 447 edition 1.1927 → withdrawn
Measuring spigot for normal thread plug gauges for Whitworth threads
DIN 448 edition 1.1927 → withdrawn
Measuring spigot for normal thread plug gauges for metric threads
DIN 449 edition 1.1927 → withdrawn
Normal thread ring gauges for Whitworth threads
DIN 450 · Edition 1.1927 → withdrawn
Normal thread ring gauges for metric threads
DIN 453 edition 12.1943 → withdrawn
Roof tiles, beaver tails
DIN 453 · Edition 6.1921 → withdrawn
Roof tiles, beaver tails, ridge tiles
DIN 454 edition 10.1922 → withdrawn
Roof tiles, small pans, roof tiles
DIN 455 edition 7.1922 → 12.1964 withdrawn
Cover plates for walls, concrete
DIN 456 Edition 8.1976 → 10.1998 replaced by DIN EN 538, DIN EN 539-1 / 2, DIN EN 1024, DIN EN 1304
Roof tiles; Requirements, testing, monitoring
DIN 456 edition 5.1958 → replaced by edition 8.1976
Roof tiles; Quality properties and test methods
DIN 456 edition 11.1937x → withdrawn
Roof tiles, concept, properties
DIN 457 - Part 1 · Edition 9.1964 → withdrawn without replacement
Cable duct blocks made of concrete; single and multi-train shaped bricks
DIN 457 - Part 2 Edition 9.1964 → withdrawn without replacement
Cable duct blocks made of concrete; Formed stone for building entries
DIN 457 - Part 3 Edition 12.1978 → 4.1987 withdrawn without replacement
Cable duct blocks made of concrete; Technical conditions, quality control
DIN 457 - Part 3 · Edition 5.1971 → replaced by Edition 12.1978
Cable duct blocks made of concrete; Technical conditions, quality control
DIN 457 edition 9.1940 → withdrawn
Cable fittings for main and distribution channels, concrete
DIN 457 Edition 7.1926 → withdrawn
Cable fittings for main and distribution channels, concrete
DIN 457 edition 10.1922 → withdrawn
Cable fittings with straight ceiling for main ducts, concrete
formerly DIN 2031
DIN 458 Edition 4.1925 → 1929 replaced by DIN 457
Cable fittings with arched ceiling for main and distribution channels, concrete
DIN 459 - Part 1 · Edition 11.1995 → current
Building material machines · Mixers for concrete and mortar · Terms, performance determination, sizes
The standard applies to mixers for the production of concrete and mortar with hydraulic binders.
DIN 459 - Part 1 · Edition 10.1993 → replaced by Edition 11.1995
Building material machines · Mixers for concrete and mortar · Terms, performance determination, sizes
DIN 459 - Part 1 · Edition 8.1972 → replaced by Edition 10.1993
Building material machines · Mixers for concrete and mortar; Terms, performance assessment, sizes
DIN 459 - Part 2 Edition 11.1995 → current
Building material machines · Mixers for concrete and mortar · Procedure for testing the mixing effect of concrete mixers
The standard applies to batchwise and continuously working mixers with a nominal volume of less than 0.25 m³
DIN 459 edition 8.1972 → replaced by DIN 459 part 1 edition 10.1993
Concrete mixer · Terms, sizes, requirements
DIN 459 · Edition 6.1946 → withdrawn
Concrete mixers · Sizes and building principles
DIN 459 edition 4.1924 → withdrawn
Concrete mixers, building principles
DIN 460 edition 10.1925 → withdrawn
Trapezoidal steel, raw
DIN 461 Edition 3.1973 → current
Graphical representation in coordinate systems
DIN 461 edition 1.1923 → withdrawn
Graphical representations through sight lines
DIN 462 edition 9.1973 → current
Machine tools · Lock washers with inner nose, for locknuts according to DIN 1804
DIN 462 edition 4.1940 → withdrawn
Lock washers with inner nose for locknuts according to DIN 1804
DIN 463 edition 7.1974 → 5.2003 withdrawn without replacement
Washers with two tabs (locking washers with 2 tabs)
DIN 463 edition 5.1943 → withdrawn
Locking plate; with two lobes
DIN 464 edition 1.2007 → current
Knurled screws, tall form
The standard specifies the properties of knurled screws, tall form, for threads from M 1 to M 10.
DIN 464 edition 8.2006 → replaced by edition 1.2007
Knurled screws, tall form
The standard specifies the properties of knurled screws, tall form, for threads from M 1 to M 10.
DIN 464 edition 9.1986 → replaced by edition 8.2006
Knurled screws, tall form
The standard contains the dimensional specifications and technical delivery conditions for high-profile knurled screws and specifies their designation.
DIN 464 edition 12.1970 → replaced by edition 9.1986
High knurled screws
DIN 464 edition 10.1943 → withdrawn
Knurled screws; high, M 1 to M 10
DIN 464 edition 3.1924 → withdrawn
High knurled screws, metric thread
DIN 465 edition 12.1970 → replaced by DIN 464 edition 9.1986
Tall knurled screws with slot
DIN 465 edition 10.1943 → withdrawn
Knurled screws; high, with slit, M 1 to M 10
DIN 465 edition 3.1924 → withdrawn
High slotted knurled screws, metric thread
DIN 466 edition 8.2006 → current
Knurled nuts, tall form
This standard specifies the properties of tall knurled nuts with threads from M 1 to M 10.
DIN 466 edition 9.1986 → replaced by edition 8.2006
Knurled nuts, tall form
The standard contains the dimensional specifications and technical delivery conditions for knurled nuts high form and specifies their designation.
DIN 466 edition 11.1970 → replaced by edition 9.1986
High knurled nut
DIN 466 edition 10.1943 → withdrawn
Knurled nuts; high, M 1 to M 10
DIN 466 edition 3.1924 → withdrawn
High knurled nut, metric thread
DIN 467 edition 8.2006 → current
Knurled nuts, low shape
The standard specifies the properties of low knurled nuts for threads M 1 to M 10.
DIN 467 edition 9.1986 → replaced by edition 8.2006
Knurled nuts, low shape
The standard contains the dimensional specifications and technical delivery conditions for knurled nuts low form and specifies their designation.
DIN 467 edition 11.1970 → replaced by edition 9.1986
Flat knurled nut
DIN 467 edition 6.1963 → withdrawn
Flat knurled nuts; Metric thread
DIN 467 edition 10.1943 → withdrawn
Knurled nuts; flat, M 1 to M 10
DIN 467 edition 3.1924 → withdrawn
Flat knurled nut, metric thread
DIN 468 · Edition 6.2014 → current
Hand cranks, cranked
The standard specifies product requirements for cranked hand cranks.
DIN 468 edition 10.2003 → replaced by edition 6.2014
Hand cranks, cranked
The standard defines dimensions and materials for cranked hand cranks.
DIN 468 edition 10.1962 → replaced by edition 10.2003
Hand cranks, cranked
DIN 468 Edition 5.1933 → withdrawn
Hand cranks, cranked
DIN 469 edition 6.2014 → current
Winches, straight
The standard specifies product requirements for straight hand cranks.
DIN 469 edition 10.2003 → replaced by edition 6.2014
Winches, straight
The standard specifies dimensions and materials for straight hand cranks.
DIN 469 edition 10.1962 → replaced by edition 10.2003
Winches, straight
DIN 469 edition 5.1933 → withdrawn
Winches, straight
DIN 470 · Edition 3.2011 → current
Locking discs
The standard specifies requirements for sealing discs with diameters from 3 mm to 125 mm.
DIN 470 edition 7.1974 → replaced by edition 3.2011
Locking washers
DIN 470 edition 8.1954 → withdrawn
Locking washers
DIN 470 edition 8.1944 → withdrawn
Locking washers
DIN 471 · Edition 4.2011 → current
Circlips (retaining rings) for shafts · standard design and heavy-duty design
The standard specifies requirements for retaining rings for shafts and the associated grooves.
DIN 471 edition 9.1981 → replaced by edition 4.2011
Circlips (retaining rings) for shafts · standard design and heavy-duty design
DIN 471 - Part 1 Issue 3.1965 → withdrawn
Circlips for shafts · standard design
DIN 471 - Part 2 Issue 3.1965 → withdrawn
Circlips for shafts · heavy duty
DIN 471 supplement 1 edition 1.1945 → withdrawn
Retaining rings for shafts · Design guidelines and installation
DIN 471 edition 11.1942 → withdrawn
Retaining rings for shafts
DIN 472 Edition 6.2017 → current
Retaining rings (retaining rings) for bores · Standard and heavy-duty versions
The standard specifies requirements for the retaining rings and the associated grooves that accommodate the retaining rings.
DIN 472 edition 10.2011 → replaced by edition 6.2017
Retaining rings (retaining rings) for bores · Standard and heavy-duty versions
DIN 472 · edition 5.2011 → replaced by edition 10.2011
Retaining rings (retaining rings) for bores · Standard and heavy-duty versions
DIN 472 edition 9.1981 → replaced by edition 5.2011
Retaining rings (retaining rings) for bores · Standard and heavy-duty versions
DIN 472 - Part 1 Issue 3.1965 → withdrawn
Circlips for bores · Standard design
DIN 472 - Part 2 Issue 3.1965 → withdrawn
Circlips for bores · heavy-duty design
DIN 472 supplement 1 edition 1.1945 → withdrawn
Retaining rings for bores · Design guidelines and installation
DIN 472 edition 11.1942 → withdrawn
Retaining rings for bores
DIN 473 edition 4.1936 → withdrawn
Cock handles with wooden handle
DIN 474 edition 1.1953 → replaced by DIN 6774-4 edition 4.1982
Drawings; Drawings (pictures) for printing purposes; Drawings for the production of printing plates and printing blocks
DIN 474 edition 1.1943 → withdrawn
Drawings (images) for printing purposes, for the production of printing plates and printing blocks
DIN 475 - Part 1 Edition 11.2016 → current
Wrench sizes for screws, fittings, fittings
The standard applies to wrench sizes for all two, four, six and eight-sided edges, even if they are not operated by a key. DIN 79 applies to all square edges and square holes for spindles, handwheels and cranks, DIN 10-1 applies to all square edges for tools.
DIN 475 - Part 1 edition 1.1984 → replaced by edition 11.2016
Wrench sizes for screws, fittings, fittings
DIN 475 - Part 1 · Edition 3.1980 → replaced by Edition 1.1984
Wrench sizes for screws, fittings, fittings
DIN 475 - Part 1 Edition 11.1965 → withdrawn
Wrench sizes for screws, fittings, fittings
DIN 475 - Part 1 · Edition 4.1928 → withdrawn
Wrench sizes
DIN 475 - Part 1 Edition 12.1921 → withdrawn
Wrench sizes
DIN 475 - Part 2 edition 11.1982 → replaced by DIN ISO 691 edition 4.2007
Widths across flats for wrenches
DIN 475 - Part 2 · Edition 4.1971 → replaced by Edition 11.1982
Widths across flats for wrenches
DIN 475 - Part 2 · Edition 1.1924 → withdrawn
Widths across flats, dimensions
DIN 475 - Part 3 · Edition 1.1987 → replaced by DIN ISO 1085 Edition 4.2007
Wrench sizes · Pairings for wrenches
The standard contains the wrench size pairings for all non-adjustable wrenches with two wrench sizes. It specifies the preferred pairings in row 1 and other common but less recommended pairings in row 2.
DIN 475 - Part 3 · Edition 4.1976 → replaced by Edition 1.1987
Wrench sizes; Pairings for wrenches
DIN 475 - Part 3 · Edition 10.1971 → replaced by Edition 4.1976
Wrench sizes; Pairings for wrenches
DIN 475 edition 1.1943x → withdrawn
Wrench sizes and mouth sizes
DIN 476 - Part 1 · Edition 2.1991 → replaced by DIN EN ISO 216 Edition 3.2002
Writing paper and certain groups of printed matter, end formats A and B series
DIN 476 - Part 2 · Edition 2.2008 → current
Final paper sizes · C series
The formats of the C series specified in the standard apply to paper products that are intended to accommodate paper products in the A series, e.g. B. Envelopes, folders, folders.
DIN 476 - Part 2 · Edition 2.1991 → replaced by Edition 2.2008
Final paper sizes · C series
DIN 476 edition 12.1976 → replaced by DIN 476 part 2 edition 2.1991 and DIN 476 part 1 edition 2.1991
Final paper sizes
DIN 476 edition 4.1939 → withdrawn
Paper sizes; Format order, folds, usage forms, printing notes
4th edition of the standard
DIN 476 edition 4.1930 → withdrawn
Paper formats, format regulations
3rd edition of the standard
DIN 476 Edition 7.1925 → withdrawn
Paper sizes
DIN 477 - Part 1 · Edition 6.2012 → current
Gas cylinder valves for cylinder test pressures up to and including 300 bar · Valve inlet and outlet connections
Requirements for gas cylinder valves and their side ports.
DIN 477 - Part 1 · Edition 3.2011 → replaced by Edition 6.2012 and DIN 477 Part 7 Edition 5.2014
Gas cylinder valves for cylinder test pressures up to and including 300 bar · Valve inlet and outlet connections
DIN 477 - part 1 edition 5.1990 → replaced by edition 3.2011, DIN EN 629 part 1 edition 8.1996 and DIN EN ISO 11116 part 1 edition 1.2000
Gas cylinder valves · For test pressures up to max. 300 bar · Types, dimensions, connections, threads
DIN 477 - Part 1 · Edition 2.1990 → replaced by Edition 5.1990
Gas cylinder valves for test pressures up to max. 300 bar · Types, dimensions, connections, threads
DIN 477 - Part 1 · Edition 9.1979 → replaced by Edition 2.1990
Gas cylinder valves for test pressures up to max. 300 bar · Types, dimensions, connections, threads
DIN 477 - Part 1 Edition 11.1963 → withdrawn
Gas cylinder valves · Types Dimensions Connections Thread
DIN 477 - Part 2 Edition 11.1963 → withdrawn
Gas cylinder valves · Technical delivery conditions
DIN 477 - part 3 edition 11.1963 → replaced by DIN 477 part 1 edition 2.1990
Gas cylinder valves · Terms and technical data for gases carried in gas cylinders
DIN 477 - Part 4 Edition 9.1982 → 9.2010 withdrawn without replacement
Gas cylinder valves · Check valves for camping cylinders
DIN 477 - Part 5 · Edition 4.2002 → current
Gas cylinder valves · For test pressures up to max. 450 bar · Side connections
The standard specifies side connections for gas cylinder valves for test pressures up to max. 450 bar fixed.
DIN 477 - Part 5 · Edition 2.1990 → replaced by Edition 4.2002
Gas cylinder valves for test pressures up to max. 450 bar · Types, dimensions, connections, threads
DIN 477 - Part 5 · Edition 9.1979 → replaced by Edition 2.1990
Gas cylinder valves for test pressures up to max. 450 bar · Types, dimensions, connections, threads
DIN 477 - Part 5 Edition 11.1972 → withdrawn
Gas cylinder valves · for test pressures up to max. 450 bar (450 kp / cm²) · Types Construction dimensions Connections Thread
DIN 477 - Part 6 Edition 3.1983 → 8.2006 withdrawn without replacement
Gas cylinder valves · For test pressures up to max. 300 bar and up to max. 450 bar, with cylindrical thread for screw-in socket and gas bottle neck for breathing apparatus · Dimensions, thread
DIN 477 - Part 7 · Edition 5.2014 → current
Gas cylinder valves for cylinder test pressures up to and including 300 barGauges for tapered thread W 31.3 × 1/14 (acetylene)
DIN 477 - Part 7 Edition 1.1984 → replaced by Edition 5.2014
Gas cylinder valves · Tapered threads · Gauges
DIN 477 edition 1.1944 → withdrawn
Gas cylinder valves, thread and connection dimensions, structural dimensions, technical delivery conditions
DIN 477 edition 4.1922 → withdrawn
Gas cylinder valves, dimensions of the connecting pieces
DIN 478 Edition 8.2016 → current
Square bolts with collar
The standard contains specifications for square bolts with collar (sizes M 5 to M 24) in product class A.
DIN 478 edition 2.1985 → replaced by edition 8.2016
Square bolts with collar
The standard contains specifications for square head screws with collar (sizes M 5 to M 24), which are mainly used as so-called adjusting screws and are subjected to pressure.
DIN 478 edition 3.1968 → replaced by edition 2.1985
Square head screws with collar · Metric thread
DIN 478 - Part 1 Edition 10.1947 → withdrawn
Square bolts; with collar, M 5 to M 24
DIN 478 - Part 1 Edition 10.1926 → withdrawn
Square head bolts with collar from M 5 to M 24
DIN 478 - Part 2 Edition 10.1926 → withdrawn
Square bolts; with collar, 1/4 "to 1"
DIN 479 edition 8.2016 → current
Square head screws with short tenons
The standard contains specifications for square bolts with a core shoulder (sizes M 5 to M 24) in product class A.
DIN 479 edition 2.1985 → replaced by edition 8.2016
Square head screws with core shoulder
The standard contains specifications for square bolts with a core shoulder (sizes M 5 to M 24), which are mainly used as so-called adjusting screws and are subjected to pressure.
DIN 479 edition 7.1968 → replaced by edition 2.1985
Square head screws with core shoulder · Metric thread, metric fine thread
DIN 479 - Part 1 · Edition 5.1942 → withdrawn
Square bolts; with core approach, M 5 to M 24
DIN 479 - Part 1 Edition 10.1926 → withdrawn
Square bolts with tenons from M 5 to M 24
DIN 479 - Part 2 Edition 10.1926 → withdrawn
Square bolts; with spigot, 1/4 "to 1"
DIN 480 edition 8.2016 → current
Square head screws with collar and shoulder tip
The standard contains specifications for square bolts with collar and shoulder (sizes M 5 to M 24) in product class A.
DIN 480 edition 2.1985 → replaced by edition 8.2016
Square head screws with collar and shoulder tip
This standard contains specifications for square bolts with collar and shoulder (sizes M 5 to M 24), which are mainly used as so-called adjusting screws and are subjected to pressure.
DIN 480 edition 3.1968 → replaced by edition 2.1985
Square head screws with collar and shoulder cap · Metric thread
DIN 480 - Part 1 · Edition 5.1942 → withdrawn
Square bolts; with collar and tenon, M 8 to M 24
DIN 480 - Part 1 · Edition 10.1926 → withdrawn
Square head bolts with collar and tenon from M 8 to M 24
DIN 480 - Part 2 · Edition 10.1926 → withdrawn
Square bolts; with collar and tenon, 5/16 "to 1"
DIN 481 edition 4.1934 → withdrawn
Small paving stones, mosaic paving stones made of natural stone
DIN 481 edition 10.1920 → withdrawn
Small paving stones, mosaic paving stones
DIN 482 edition 4.2002 → current
Road curbs made of natural stone
In addition to EN 1343, the standard specifies shapes and profiles for natural stone curbstones that are used in Germany. Specifications on requirements, properties and test methods are not part of the standard; these are contained in EN 1343.
DIN 482 edition 9.1988 → replaced by edition 4.2002 and DIN EN 1343 edition 3.2000
Road curbs made of natural stone
DIN 482 edition 11.1974 → replaced by edition 9.1988
Curbs, natural stone
DIN 482 Edition 7.1964 → withdrawn
Curbs; Natural stone
DIN 482 Edition 7.1941 → withdrawn
Borders and curbs made of natural stone
DIN 482 edition 4.1928 → withdrawn
Borders, curbs, natural stone
DIN 482 Edition 10.1920 → withdrawn
Borders, curbs, natural stone
DIN 483 edition 10.2005 → current
Concrete curbs - shapes, dimensions, marking
In addition to EN 1340, the standard specifies shapes and profiles for curb stones made of concrete that are used in Germany. Specifications on requirements, properties and test methods are not part of the standard; these are contained in EN 1340.
DIN 483 · edition 4.2004 → replaced by edition 10.2005
Concrete curbs - shapes, dimensions, marking
In addition to prEN 1340, the standard specifies shapes and profiles for curb stones made of concrete that are used in Germany. Specifications for requirements, properties and test methods are not part of the standard; these are contained in prEN 1340.
DIN 483 edition 8.1981 → 4.2004 replaced by edition 4.2004 and DIN EN 1340 edition 8.2003
Concrete curbs
DIN 483 edition 9.1963 → withdrawn
Curbs; concrete
DIN 483 edition 1.1934 → withdrawn
Concrete curbs and curbs, terms of delivery and testing
DIN 483 edition 10.1920 → withdrawn
Curbs, curbs, concrete
DIN 484 edition 10.1920 → probably withdrawn in May 1963
Sidewalk slabs; Natural stone
DIN 485 edition 4.1987 → replaced by DIN EN 1339 edition 8.2003
Concrete paving slabs
The standard applies to concrete pavement slabs with or without facing concrete made from hydraulic binders and mineral aggregates, which, according to DIN 4226 Part 1, have sufficient resistance to frost if the concrete is very damp. Cements in accordance with DIN 1164 Part 1 or suitable cements approved by the building authorities are to be used as binding agents. Additives must not adversely affect the resistance to frost and de-icing salt. The standard sets requirements for the quality, shape and dimensions, flexural strength and resistance to frost and de-icing salt.
DIN 485 · Edition 6.1963x → withdrawn
Concrete paving slabs
DIN 485 edition 1.1934 → withdrawn
Concrete sidewalk slabs, terms of delivery and testing
DIN 485 Edition 10.1920 → withdrawn
Pavement slabs, concrete
DIN 486 edition 1.1923 → 12.1964 withdrawn
Floor panels and wall panels
DIN 487 edition 3.1971 → current
Boundary stones; Number stones, concrete
DIN 487 edition 10.1922 → withdrawn
Boundary stones, number stones; concrete
DIN 488 - Part 1 · Edition 8.2009 → current
Reinforcing steel · Steel types, properties, labeling
The standard applies to weldable types of steel for reinforcing concrete. It does not apply to prestressing steel for the reinforcement of prestressed concrete in accordance with DIN 4227 Part 1. The use of reinforcing steel that deviates from this standard requires the approval of the supreme building supervisory authority in individual cases, unless a general building supervisory authority Approval is granted.
DIN 488 - Part 1 · Edition 9.1984 → replaced by Edition 8.2009 and DIN EN 10080 Edition 8.2005
Reinforcing steel · Types, properties, characteristics
DIN 488 - Part 1 · Edition 4.1972 → replaced by Edition 9.1984
Reinforcing steel · Terms, properties, factory identification
DIN 488 - Part 2 · Edition 8.2009 → current
Reinforcing bars · Reinforcing bars
The standard specifies the nominal diameter and the requirements for the surface shape of ribbed bars made of the reinforcing steel types BSt 420S and BSt 500S according to DIN 488 Part 1. The standard contains specifications on the dimensions, shape and arrangement of the inclined and longitudinal ribs as well as the values for the related rib area depending on the nominal diameter.
DIN 488 - Part 2 · Edition 6.1986 → replaced by Edition 8.2009 and DIN EN 10080 Edition 8.2005
Reinforcing steel · Reinforcing steel · Dimensions and weights
DIN 488 - Part 2 · Edition 4.1972 → replaced by Edition 6.1986
Reinforcing bars · Reinforcing bars · Dimensions
DIN 488 - Part 3 · Edition 8.2009 → current
Reinforcing steel · Reinforcing steel in rings, reinforcing wire
DIN 488 - Part 3 · Edition 6.1986 → replaced by DIN EN ISO 15630-1 Edition 9.2002
Reinforcing steel · Testing of reinforcing steel
DIN 488 - Part 3 · Edition 4.1972 → replaced by Edition 6.1986
Reinforcing bars · reinforcing bars · tests
DIN 488 - Part 4 Edition 8.2009 → current
Reinforcing steel · welded wire mesh
The standard describes the structure of welded welded steel mesh from ribbed bars and contains the requirements for the dimensions and tolerances for diameter, cross-section and surface shape of the individual bars for the production of welded welded wire mesh and reinforcing wire with smooth and profiled surfaces.
DIN 488 - Part 4 Edition 6.1986 → replaced by Edition 8.2009 and DIN 488 Part 3 Edition 8.2009
Reinforcing steel · welded wire mesh and reinforcing wire · structure, dimensions and weights
DIN 488 - Part 4 · Edition 4.1972 → replaced by Edition 6.1986
Reinforcing steel · welded wire mesh · structure
DIN 488 - Part 5 Edition 8.2009 → current
Reinforcing steel lattice girders
DIN 488 - Part 5 edition 6.1986 → replaced by DIN EN ISO 15630 parts 1 and 2 edition 9.2002
Reinforcing steel · welded wire mesh and reinforcing wire · tests
DIN 488 - Part 5 · Edition 4.1972 → replaced by Edition 6.1986
Reinforcing steel · welded wire mesh; exams
DIN 488 - Part 6 · Edition 1.2010 → current
Reinforcing steel · Certificate of conformity
The standard applies to the quality monitoring of reinforcing steel bars, welded wire mesh and reinforcing wire made of the steel types according to DIN 488 Part 1. It contains specifications on the type, scope and evaluation of the tests during the initial test as well as for internal and external monitoring of the products.
DIN 488 - Part 6 · Edition 8.2009 → replaced by Edition 1.2010
Reinforcing steel · Certificate of conformity
DIN 488 - Part 6 · Edition 6.1986 → replaced by Edition 8.2009
Reinforcing steel monitoring (quality monitoring)
DIN 488 - Part 6 Edition 9.1973
Reinforcing steel monitoring (quality monitoring)
DIN 488 - Part 7 Edition 6.1986 → 11.2010 withdrawn without replacement
Reinforcing steel · Proof of weldability of reinforcing steel · Implementation and evaluation of the tests
The standard describes the verification of the weldability of the reinforcing steel bars BSt 420S and BSt 500S according to DIN 488 Part 1. It contains the specifications for the implementation (scope of testing, materials, test method) as well as the evaluation of the tests during the initial test and for the verification of the quality level.
DIN 488 Edition 3.1939 → withdrawn
Round bars for reinforced concrete
DIN 488 Edition 7.1923 → withdrawn
Round iron for reinforced concrete
DIN 489 edition 7.1923 → 12.1964 withdrawn
Steps, landing plates, concrete
DIN 490 edition 1.1924 → withdrawn
Driving wedges, chocks
DIN 491 edition 1.1924 → withdrawn
Flat wedges
DIN 492 edition 1.1924 → withdrawn
Hollow wedges
DIN 493 edition 1.1924 → replaced by DIN 6887 edition 10.1948
Nose wedges
DIN 494 edition 1.1924 → replaced by DIN 6884 edition 9.1948
Flat nose wedges
DIN 495 edition 8.1924 → replaced by DIN 6889 edition 11.1948
Nasal wedges
DIN 496 - Part 1 Edition 7.1927 → withdrawn
Parallel keys, sliding springs
DIN 496 - Part 2 Edition 7.1927 → withdrawn
Parallel keys, sliding springs
DIN 496 edition 1.1924 → withdrawn
Parallel keys, sliding springs
DIN 497 edition 4.1930 → withdrawn
Drawn wedge steel, -3 fitting units according to DIN 773 for width + 20 / + 10 fitting units according to DIN 773 for height
2nd edition of the standard
DIN 497 edition 4.1924 → replaced by edition 4.1930
Flat steel, drawn, accuracy -3 units according to DIN 773 for width + 20 / + 10 units according to DIN 773 for height
1st edition of the standard
DIN 498 · Edition 6.1929 → withdrawn
Drawn wedge steel, + 20 / + 10 fitting units according to DIN 773
2nd edition of the standard
DIN 498 edition 4.1924 → replaced by edition 6.1929
Flat steel, drawn, accuracy + 20 / + 10 units according to DIN 773
1st edition of the standard
DIN 499 edition 4.1924 → drawn in April / May 1949
Hollow flat steel, drawn, accuracy -10 units according to DIN 773 for width and + 20 / + 10 units according to DIN 773 for thickness
Selected historical draft standards
DIN 2 ??
Weights of the taper pins
Draft in issue 1 of the DIN-Mitteilungen in January 1918
DIN 4 ??
Drawings, dimensions of the normal sheet
Draft in issue 1 of the DIN-Mitteilungen in January 1918
See also
swell
- DIN standard sheet directory 1926 (Beuth-Verlag, Berlin)
- DIN standard sheet directory 1931 (Beuth-Verlag, Berlin)
- DIN standard sheet directory 1950 (Beuth-Vertrieb GmbH, Berlin)
- DIN standard sheet directory 1956 (Beuth-Vertrieb GmbH, Berlin)
- DIN standard sheet directory 1974 (Beuth-Vertrieb GmbH, Berlin)
- DIN standards committees (all valid, as well as new and withdrawn standards of the respective standards committee)
- Beuth Verlag - Product search
- Beuth Verlag - Search for historical documents (registration required)