List of standards DIN 1000 to DIN 1499
The list of standards DIN 1000 to DIN 1499 lists all current standards and many historical standard editions in the number range 1000 to 1499.
DIN - German Institute for Standardization e. V. - is the national standardization organization of the Federal Republic of Germany based in Berlin .
Explanations of the list
- DIN-EN standards, DIN-EN-ISO standards, DIN-ISO standards, preliminary standards and draft standards are not listed in this list.
- The term “sheet” used in older standard editions has been uniformly transferred to “part”.
- The date of issue is indicated next to the standard number. Edition 9.1981 means that the standard was published in September 1981.
- Cross edition: If the date of issue is appended with an x, for example edition 9.1949x, the standard has only been changed slightly and remains valid.
- Unless otherwise noted, the withdrawal date of an old standard is the same as the issue date of the replacing standard (s).
- The entry "→ current" means that the standard is currently (as of June 2017) valid.
DIN 1000 edition 12.1973 → replaced by DIN 18800 part 7 edition 5.1983
Steel structures · Execution
DIN 1013 - Part 1 edition 11.1976 → replaced by DIN EN 10060 edition 2.2004
Bars · Hot-rolled round bars for general use, dimensions, permissible dimensional and shape deviations
DIN 1013 - Part 2 edition 11.1976 → replaced by DIN EN 10060 edition 2.2004
Bar steel · Hot-rolled round steel for special uses, dimensions, permissible dimensional and shape deviations
DIN 1014 - Part 1 edition 7.1978 → replaced by DIN EN 10059 edition 2.2004
Bars · Hot-rolled square steel for general use, dimensions, permissible dimensional and shape deviations
DIN 1014 - Part 2 Edition 7.1978 → replaced by DIN EN 10059 Edition 2.2004
Bars · Hot-rolled square steel for special uses, dimensions, permissible deviations in dimensions and shape
DIN 1015 edition 11.1972 → replaced by DIN EN 10061 edition 2.2004
Bars · Hot-rolled hexagonal steel, dimensions, weights, permissible deviations
DIN 1016 · edition 6.1987 → replaced by DIN EN 10051 edition 2.1992 and DIN EN 10048 edition 10.1996
Flat products made of steel · Hot-rolled strip, hot-rolled sheet metal · Limiting dimensions, shape and weight tolerances
DIN 1016 edition 11.1972 → replaced by edition 6.1987
Flat goods made of steel · Hot-rolled strip, hot-rolled sheet metal less than 3 mm thick · Dimensions, permissible deviations in size, shape and weight
DIN 1017 - Part 1 · Edition 4.1967 → replaced by DIN EN 10058 Edition 2.2004
Bars · Hot-rolled flat steel for general use, dimensions, weights, permissible deviations
DIN 1017 - part 2 edition 3.1964 → replaced by DIN EN 10058 edition 2.2004
Bar steel · Hot-rolled flat steel for special use (in bar drawing shops, screw mills etc.), dimensions, weights, permissible deviations
DIN 1018 edition 10.1963 → withdrawn
Bars · Hot-rolled half-round steel and flat half-round steel, dimensions, weights, permissible deviations
DIN 1019 edition 1.1977 → replaced by DIN EN 10067 edition 12.1996
Bars · Hot-rolled flat rolled steel, dimensions, weights, permissible deviations, static values
DIN 1020 Edition 10.1963 → withdrawn
Bars · Hot-rolled bead angle steel, dimensions, weights, permissible deviations, static values
DIN 1022 edition 4.2004 → current
Bar steel · Hot-rolled isosceles, sharp-edged angle steel (LS steel) · Dimensions, dimensions and tolerances
DIN 1022 edition 10.1963 → replaced by edition 4.2004
Bar steel · Hot-rolled isosceles, sharp-edged angle steel (LS steel) · Dimensions, dimensions and tolerances
DIN 1024 edition 3.1982 → replaced by DIN EN 10055 edition 12.1995
Bar steel · Hot-rolled round-edged T-steel · Dimensions, weights, permissible deviations, static values
DIN 1024 edition 8.1981 → replaced by edition 3.1982
Bar steel · Hot-rolled round-edged T-steel · Dimensions, weights, permissible deviations, static values
DIN 1025 - Part 1 · Edition 4.2009 → current
Hot-rolled I-beams · Narrow I-beams, I-series · Dimensions, mass, static values
DIN 1025 - Part 1 · Edition 5.1995 → replaced by Edition 4.2009
Hot-rolled I-beams · Narrow I-beams, I-series · Dimensions, mass, static values
DIN 1025 - Part 1 edition 10.1963 → replaced by edition 5.1995 and DIN EN 10024 edition 5.1995
Sectional steel · Hot-rolled I-beams, narrow I-beams, I-series · Dimensions, weights, permissible deviations, static values
DIN 1025 - Part 2 Edition 11.1995 → current
Hot-rolled I-beams · I-beams, IPB series · Dimensions, mass, static values
DIN 1025 - Part 2 · Edition 3.1994 → replaced by Edition 11.1995
Hot-rolled I-beams · Width I-beams, IPB and IB series · Dimensions, mass, static values
DIN 1025 - Part 2 · Edition 10.1963 → replaced by Edition 3.1994 and DIN EN 10034 Edition 3.1994
Sectional steel · Hot-rolled I-beams, width I-beams, IPB and IB series · Dimensions, weights, permissible deviations, static values
DIN 1025 - Part 3 · Edition 3.1994 → current
Hot-rolled I-beams · Wide I-beams, light design, IPBl series · Dimensions, mass, static values
DIN 1025 - Part 3 · Edition 10.1963 → replaced by Edition 3.1994 and DIN EN 10034 Edition 3.1994
Sectional steel · Hot-rolled I-beams, width I-beams, light design, IPBl series · Dimensions, weights, permissible deviations, static values
DIN 1025 - Part 4 Edition 3.1994 → current
Hot-rolled I-beams · Wide I-beams, reinforced design, IPBv series · Dimensions, mass, static values
DIN 1025 - Part 4 Edition 10.1963 → replaced by Edition 3.1994 and DIN EN 10034 Edition 3.1994
Sectional steel · Hot-rolled I-beams, width I-beams, reinforced design, IPBv series · Dimensions, weights, permissible deviations, static values
DIN 1025 - Part 5 Edition 3.1994 → current
Hot-rolled I-beams · Middle width I-beams, IPE series · Dimensions, mass, static values
DIN 1025 - Part 5 · Edition 3.1965 → replaced by Edition 3.1994 and DIN EN 10034 Edition 3.1994
Sectional steel · Hot-rolled I-beams, middle width I-beams, IPE series · Dimensions, weights, permissible deviations, static values
DIN 1026 - Part 1 Edition 9.2009 → current
Hot-rolled U-profile steel U-profile steel with inclined flange surfaces Dimensions, mass and static values
Correction of edition 4.2009
DIN 1026 - Part 1 · Edition 4.2009 → replaced by Edition 9.2009
Hot-rolled U-profile steel U-profile steel with inclined flange surfaces Dimensions, mass and static values
DIN 1026 - Part 1 · Edition 11.2002 → replaced by Edition 4.2009
Hot-rolled U-profile steel · Hot-rolled U-profile steel with inclined flange surfaces · Dimensions, mass and static values
Correction of edition 3.2000
DIN 1026 - Part 1 · Edition 3.2000 → replaced by Edition 11.2002
Hot-rolled U-profile steel · Hot-rolled U-profile steel with inclined flange surfaces · Dimensions, mass and static values
DIN 1026 - Part 2 · Edition 10.2002 → current
Hot-rolled U-profile steel U-profile steel with parallel flange surfaces Dimensions, mass and static values
DIN 1027 · Edition 4.2004 → current
Bars · Hot-rolled, round-edged Z-steel · Dimensions, mass, tolerances, static values
DIN 1027 edition 10.1963 → replaced by edition 4.2004
Bars · Hot-rolled, round-edged Z-steel · Dimensions, weights, permissible deviations, static values
DIN 1028 edition 3.1994 → replaced by DIN EN 10056 part 1 edition 10.1998
Hot-rolled, isosceles, round-edged angle steel · Dimensions, mass, static values
DIN 1028 edition 10.1976 → replaced by edition 3.1994 and DIN EN 10056 part 2 edition 3.1994
Bar steel · Hot-rolled, isosceles, round-edged angle steel · Dimensions, weights, permissible deviations, static values
DIN 1029 edition 3.1994 → replaced by DIN EN 10056 part 1 edition 10.1998
Hot-rolled, unequal-sided, round-edged angle steel · Dimensions, mass, static values
DIN 1029 edition 7.1978 → replaced by edition 3.1994 and DIN EN 10056 part 2 edition 3.1994
Bar steel · Hot-rolled, unequal-sided, round-edged angle steel · Dimensions, weights, permissible deviations, static values
DIN 1041 edition 12.2009 → current
Locksmith's hammers
The standard specifies the dimensions and weights of locksmith's hammers and contains safety-related specifications.
DIN 1041 edition 2.2001 → replaced by edition 12.2009
Locksmith's hammers
DIN 1041 edition 9.2000 → replaced by edition 2.2001
Locksmith's hammers
DIN 1041 edition 12.1991 → replaced by edition 9.2000
Locksmith's hammers
DIN 1041 edition 12.1976 → replaced by edition 12.1991
Locksmith's hammers
DIN 1042 Edition 9.2000 → current
Sledge hammers, common hammer hammers
DIN 1042 edition 12.1991 → replaced by edition 9.2000
Sledge hammers, common hammer hammers
DIN 1042 edition 12.1976 → replaced by edition 12.1991
Sledge hammers, common hammer hammers
DIN 1045 - part 1 edition 8.2008 → replaced by DIN EN 1992 parts 1 and 3 edition 1.2011 (including national annexes)
Structures made of concrete, reinforced concrete and prestressed concrete · Dimensioning and construction
DIN 1045 - Part 1 - Correction 2 · Edition 6.2005 → replaced by DIN 1045 Part 1 Edition 8.2008
Structures made of concrete, reinforced concrete and prestressed concrete · Dimensioning and construction · Corrections to DIN 1045-1: 2001-07
DIN 1045 - Part 1 - Correction 1 Edition 7.2002 → replaced by DIN 1045 Part 1 Edition 8.2008
Structures made of concrete, reinforced concrete and prestressed concrete · Dimensioning and construction · Corrections to DIN 1045-1: 2001-07
DIN 1045 - Part 1 · Edition 7.2001 → replaced by Edition 8.2008
Structures made of concrete, reinforced concrete and prestressed concrete · Dimensioning and construction
DIN 1045 - Part 2 · Edition 8.2008 → current
Structures made of concrete, reinforced concrete and prestressed concrete · Concrete · Definition, properties, production and conformity · Application rules for DIN EN 206-1
DIN 1045 - Part 2 - Amendment A2 · Edition 6.2007 → replaced by DIN 1045 Part 2 Edition 8.2008
Structures made of concrete, reinforced concrete and prestressed concrete · Concrete · Definition, properties, production and conformity · Application rules for DIN EN 206-1 · Amendment A2
DIN 1045 - Part 2 - Amendment A1 Edition 1.2005 → replaced by Amendment A2 Edition 6.2007
Structures made of concrete, reinforced concrete and prestressed concrete · Concrete · Specifications, properties, production and conformity · Application rules for DIN EN 206-1 · Amendment A1
DIN 1045 - Part 2 - Correction 1 · Edition 6.2002 → replaced by Edition 8.2008
Structures made of concrete, reinforced concrete and prestressed concrete · Concrete · Definition, properties, production and conformity · Application rules for DIN EN 206-1 · Corrections to DIN 1045-2: 2001-07
DIN 1045 - Part 2 edition 7.2001 → replaced by edition 8.2008
Structures made of concrete, reinforced concrete and prestressed concrete · Concrete · Definition, properties, production and conformity · Application rules for DIN EN 206-1
DIN 1045 - Part 3 - Correction 1 · Edition 7.2013 → current
Structures made of concrete, reinforced concrete and prestressed concrete · Construction · Application rules for DIN EN 13670 · Correction to DIN 1045-3: 2012-03
DIN 1045 - Part 3 · Edition 3.2012 → current
Structures made of concrete, reinforced concrete and prestressed concrete · Construction · Application rules for DIN EN 13670
The standard applies together with DIN EN 13670 for the execution of supporting structures made of concrete, reinforced concrete and prestressed concrete. It defines national application rules that are required for the application of DIN EN 13670.
DIN 1045 - Part 3 · Edition 8.2008 → replaced by Edition 3.2012 and DIN EN 13670 Edition 3.2011
Structures made of concrete, reinforced concrete and prestressed concrete · Construction work
DIN 1045 - Part 3 - Amendment A1 · Edition 1.2005 → replaced by DIN 1045 Part 3 Edition 8.2008
Structures made of concrete, reinforced concrete and prestressed concrete · Construction · Change A1
DIN 1045 - Part 3 - Correction 1 · Edition 6.2002 → replaced by DIN 1045 Part 3 Edition 8.2008
Structures made of concrete, reinforced concrete and prestressed concrete · Construction work · Corrections to DIN 1045-3: 2001-07
DIN 1045 - Part 3 · Edition 7.2001 → replaced by Edition 8.2008
Structures made of concrete, reinforced concrete and prestressed concrete · Construction work
DIN 1045 - Part 4 Edition 2.2012 → current
Structures made of concrete, reinforced concrete and prestressed concrete · Supplementary rules for the manufacture and conformity of precast elements
DIN 1045 - Part 4 Edition 7.2001 → replaced by Edition 2.2012
Structures made of concrete, reinforced concrete and prestressed concrete · Supplementary rules for the manufacture and conformity of precast elements
DIN 1045 - Part 100 · Edition 12.2011 → current
Dimensioning and construction of reinforced and prestressed concrete structures · brick ceilings
The standard applies to the calculation and execution of brick ceilings
DIN 1045 - Part 100 · Edition 2.2005 → replaced by Edition 12.2011
Concrete, reinforced and prestressed concrete structures · Brick ceilings
DIN 1045 - Amendment A1 · Edition 12.1996 → replaced by DIN 1045 Part 2 Edition 7.2001 and DIN EN 206 Part 1 Edition 7.2001
Concrete and reinforced concrete · Dimensioning and execution · Changes
DIN 1045 · Edition 7.1988 → replaced by DIN 1045 Parts 1, 2, 3 and 4 Edition 7.2001 and DIN EN 206 Part 1 Edition 7.2001
Concrete and reinforced concrete · Dimensioning and execution
DIN 1045 edition 12.1978 → replaced by edition 7.1988
Concrete and reinforced concrete · Dimensioning and execution
DIN 1045 edition 1.1972 → replaced by edition 12.1978
Concrete and reinforced concrete construction · Dimensioning and execution
DIN 1045 - Part A · Edition 11.1959 → replaced by DIN 1045 Edition 1.1972
Provisions for the execution of reinforced concrete structures
DIN 1045 - Part A · Edition 4.1943 → replaced by Edition 11.1959
Provisions for the execution of reinforced concrete structures
DIN 1045 edition 5.1937 → replaced by DIN 1045 part A edition 4.1943
DIN 1045 edition 4.1932 → replaced by edition 5.1937
DIN 1045 edition 9.1925 → replaced by edition 4.1932
Provisions for the execution of reinforced concrete structures
DIN 1048 - Part 1 · Edition 6.1991 → withdrawn
Test method for concrete · fresh concrete
DIN 1048 - part 1 edition 12.1978 → replaced by edition 6.1991 and DIN 1048 part 5 edition 6.1991
Test method for concrete · Fresh concrete, hardened concrete, separately produced test specimens
DIN 1048 - Part 1 · Edition 1.1972 → replaced by Edition 12.1978
Test method for concrete · Fresh concrete, hardened concrete, separately produced test specimens
DIN 1048 - Part 2 · Edition 6.1991 → withdrawn
Test methods for concrete · hardened concrete in structures and components
DIN 1048 - Part 2 · Edition 2.1976 → replaced by Edition 6.1991
Test method for concrete · Determination of the compressive strength of hardened concrete in buildings and components, general method
DIN 1048 - Part 2 · Edition 1.1972 → replaced by Edition 2.1976
Test method for concrete · hardened concrete of finished structures and structural members
DIN 1048 - part 3 edition 1.1975 → replaced by DIN 1048 part 1 edition 12.1978
Test method for concrete · Determination of the static modulus of elasticity
DIN 1048 - Part 4 Edition 6.1991 → withdrawn
Test method for concrete · Determination of the compressive strength of hardened concrete in buildings and components · Use of reference lines and evaluation with special methods
DIN 1048 - Part 5 · Edition 6.1991 → withdrawn
Test method for concrete · hardened concrete, separately manufactured test specimens
DIN 1048 - part 5 edition 12.1978 → replaced by edition 6.1991 and DIN 1048 part 1 edition 6.1991
Test method for concrete · Fresh concrete, hardened concrete, separately produced test specimens
DIN 1052 - Part 10 · Edition 5.2012 → current
Manufacture and execution of wooden structures · Supplementary provisions
The standard supplements DIN EN 1995 Part 1-1 and the associated national annex as well as reference standards for these two standards with regard to the requirements for manufacture and execution.
DIN 1052 - Correction 1 · Edition 5.2010 → replaced by DIN 1052 Part 10 Edition 5.2012 and DIN EN 1995 Part 1-1 including the National Annex Edition 12.2010
Manufacture and execution of wooden structures · Supplementary provisions
The standard supplements DIN EN 1995 Part 1-1 and the associated national annex as well as reference standards for these two standards with regard to the requirements for manufacture and execution.
DIN 1052 · Edition 12.2008 → replaced by DIN 1052 Part 10 Edition 5.2012 and DIN EN 1995 Part 1-1 including the National Annex Edition 12.2010
Design, calculation and dimensioning of wooden structures · General dimensioning rules and dimensioning rules for building construction
DIN 1052 edition 8.2004 → replaced by edition 12.2008
Design, calculation and dimensioning of wooden structures · General dimensioning rules and dimensioning rules for building construction
DIN 1052 - Part 1 - Amendment 1 Edition 10.1996 → replaced by DIN 1052 Edition 8.2004
Timber structures · Calculation and execution · Change 1
DIN 1052 - Part 1 · Edition 4.1988 → replaced by DIN 1052 Edition 8.2004
Timber structures · Calculation and execution
DIN 1052 - Part 1 edition 10.1969 → replaced by edition 4.1988
Timber structures · Calculation and execution
DIN 1052 - Part 2 - Amendment 1 Edition 10.1996 → replaced by DIN 1052 Edition 8.2004
Timber structures Mechanical connections Amendment 1
DIN 1052 - Part 2 · Edition 4.1988 → replaced by DIN 1052 Edition 8.2004
Timber structures · Mechanical connections
DIN 1052 - Part 2 edition 10.1969 → replaced by edition 4.1988
Timber structures · Regulations for special type of dowel connections
DIN 1052 - Part 3 - Amendment 1 Edition 10.1996 → replaced by DIN 1052 Edition 8.2004
Timber structures · Wooden houses in panel construction · Calculation and execution · Change 1
DIN 1052 - Part 3 · Edition 4.1988 → replaced by DIN 1052 Edition 8.2004
Timber structures · Wooden houses in panel construction · Calculation and execution
DIN 1053 - Part 1 · Edition 11.1996 → replaced by DIN EN 1996 Parts 1-1, 2 and 3 Edition 12.2010 including their national annexes
Masonry · Calculation and execution
DIN 1053 - Part 1 · Edition 2.1990 → replaced by Edition 11.1996
Masonry · Recipe masonry · Calculation and execution
DIN 1053 - Part 1 edition 11.1974 → replaced by edition 2.1990 and DIN 1053 part 3 edition 2.1990
Masonry · Calculation and execution
DIN 1053 - Part 2 Edition 11.1996 → withdrawn
Masonry · Masonry strength classes based on suitability tests
DIN 1053 - part 2 edition 7.1984 → replaced by edition 11.1996 and DIN 1053 part 1 edition 11.1996
Masonry · Masonry after qualification test · Calculation and execution
DIN 1053 - part 3 edition 2.1990 → replaced by DIN EN 1996 parts 1-1 and 2 editions 12.2010 including their national editions 1.2012
Masonry · Reinforced masonry · Calculation and execution
DIN 1053 - Part 4 · Edition 4.2013 → current
Masonry · prefabricated components
The standard applies primarily to storey-high and room-wide prefabricated components.
DIN 1053 - Part 4 · Edition 5.2011 → replaced by Edition 4.2013
Masonry · prefabricated components
DIN 1053 - part 4 edition 12.2009 → replaced by edition 5.2011
Masonry · prefabricated components
DIN 1053 - part 4 edition 2.2004 → replaced by edition 12.2009
Masonry · prefabricated components
DIN 1053 - Part 4 Edition 9.1978 → replaced by Edition 2.2004
Masonry · Buildings made from prefabricated brick components
DIN 1053 - part 100 edition 9.2007 → replaced by DIN EN 1996 parts 1-1 and 3 editions 12.2010 including their national annexes 1.2012
Masonry · Calculation based on the semi-probabilistic safety concept
DIN 1053 - Part 100 · Edition 8.2006 → replaced by Edition 9.2007
Masonry · Calculation based on the semi-probabilistic safety concept
DIN 1053 - Part 100 · Edition 8.2004 → replaced by Edition 8.2006
Masonry · Calculation based on the semi-probabilistic safety concept
DIN 1053 edition 11.1962 → replaced by DIN 1053 part 1 edition 11.1974
Masonry · Calculation and execution
DIN 1053 edition 12.1952 → replaced by edition 11.1962
Masonry · Calculation and execution
DIN 1053 edition 2.1937 → replaced by edition 12.1952
Components made from artificial and natural stones · Calculation bases
DIN 1054 - Amendment A2 · Edition 11.2015 → current
SubsoilSafety evidence in earthworks and foundation workSupplementary regulations to DIN EN 1997-1 Change 2
The standard contains changes to DIN 1054 edition 12.2010.
DIN 1054 - Amendment A1 · Edition 8.2012 → current
SubsoilSafety certificates in earthworks and foundation workSupplementary regulations to DIN EN 1997-1: 2010
The standard contains changes to DIN 1054 edition 12.2010.
DIN 1054 Edition 12.2010 → current
Subsoil · Proof of safety in earthworks and foundation work · Supplementary regulations to DIN EN 1997-1
The standard contains national supplements to DIN EN 1997 Part 1 Edition 9.2009.
DIN 1054 - Amendment A1 · Edition 7.2009 → replaced by DIN 1054 Edition 2010.12 and DIN EN 1997 Part 1 Edition 9.2009 including the national annex Edition 12.2010
Subsoil · Proof of safety in earthworks and foundation work · Amendment A1
The change A1 to DIN 1054 edition 1.2005 contains the adaptation of the test forces for anchors to the partial safety concept.
DIN 1054 - Correction 4 · Edition 10.2008 → replaced by DIN 1054 Edition 2010.12 and DIN EN 1997 Part 1 Edition 9.2009 including the national appendix Edition 12.2010
Subsoil · Proof of safety in earthworks and foundation work · Corrections to DIN 1054: 2005-01
DIN 1054 - Correction 3 · Edition 1.2008 → replaced by DIN 1054 Edition 2010.12 and DIN EN 1997 Part 1 Edition 9.2009 including the national appendix Edition 12.2010
Subsoil · Proof of safety in earthworks and foundation work · Corrections to DIN 1054: 2005-01
DIN 1054 - Correction 2 · Edition 4.2007 → replaced by DIN 1054 Edition 2010.12 and DIN EN 1997 Part 1 Edition 9.2009 including the national annex Edition 12.2010
Subsoil · Proof of safety in earthworks and foundation work · Corrections to DIN 1054: 2005-01
DIN 1054 - Correction 1 · Edition 4.2005 → replaced by DIN 1054 Edition 2010.12 and DIN EN 1997 Part 1 Edition 9.2009 including the national appendix Edition 12.2010
Subsoil · Proof of safety in earthworks and foundation work · Corrections to DIN 1054: 2005-01
DIN 1054 edition 1.2005 → replaced by edition 2010.12 and DIN EN 1997 part 1 edition 9.2009 including the national annex edition 12.2010
Subsoil · Proof of safety in earthworks and foundations
DIN 1054 - Correction 1 · Edition 10.2003 → replaced by DIN 1054 Edition 1.2005
Subsoil · Proof of safety in earthworks and foundation work · Corrections to DIN 1054: 2003-01
DIN 1054 edition 1.2003 → replaced by edition 1.2005
Subsoil · Proof of safety in earthworks and foundations
DIN 1054 edition 11.1976 → replaced by edition 1.2003
Subsoil · Permissible load on the subsoil
DIN 1054 - Supplement · Edition 11.1976 → replaced by DIN 1054 Edition 1.2003
Subsoil · Permissible load on the subsoil · Explanations
DIN 1055 - Part 2 · Edition 11.2010 → current
Effects on structures · Soil parameters
The standard specifies empirical values for soil parameters.
DIN 1055 - Part 2 · Edition 2.1976 → replaced by Edition 11.2010
Effects on structures · Soil parameters
DIN 1056 edition 1.2009 → current
Free-standing chimneys in solid construction · Support tube made of masonry · Calculation and execution
The standard contains specifications for the calculation and design of free-standing chimneys in solid construction, the supporting tube of which is made of masonry. It supplements DIN EN 13084-2 and DIN EN 13084-4.
DIN 1056 edition 10.1984 → replaced by edition 1.2009
Free-standing chimneys in solid construction · Calculation and execution
DIN 1056 - Part 1 edition 8.1969 → replaced by DIN 1056 edition 10.1984
Free-standing chimneys in solid construction · Calculation and execution
DIN 1056 - Part 2 Edition 8.1969 → replaced by DIN 1056 Edition 10.1984
Free-standing chimneys in solid construction · Guidelines for testing building materials and components
DIN 1058 edition 8.1969 → replaced by DIN 1056 edition 10.1984
Acid chimneys in solid construction · Calculation and execution
DIN 1072 - supplement 1 · edition 5.1988 → withdrawn
Road and road bridges · Load assumptions · Explanations
DIN 1072 - supplement 1 edition 7.1987 → replaced by supplement 1 edition 5.1988
Road and road bridges · Load assumptions · Explanations
DIN 1072 edition 12.1985 → withdrawn
Road and road bridges · Load assumptions
DIN 1072 - supplement 1 edition 12.1985 → replaced by supplement 1 edition 7.1987
Road and road bridges · Load assumptions · Explanations
DIN 1072 edition 11.1967 → replaced by edition 12.1985
Road and road bridges · Load assumptions
DIN 1072 - supplementary sheet · edition 11.1967 → replaced by supplementary sheet 1 edition 12.1985
Road and road bridges · Load assumptions · Explanations
DIN 1076 edition 11.1999 → current
Engineering structures in the course of roads and paths · Monitoring and testing
DIN 1076 edition 3.1983 → replaced by edition 11.1999
Engineering structures in the course of roads and paths · Monitoring and testing
DIN 1081 Edition 3.2017 → current
Ceramic refractory products · Dimensions · Fireproof rectangular bricks
The standard specifies dimensions and designations for refractory rectangular bricks with lengths of 230 mm, 250 mm, 300 mm, 345 mm and 375 mm.
DIN 1081 edition 1.1988 → replaced by edition 3.2017
Ceramic refractory materials · Fireproof rectangular bricks · Dimensions
DIN 1081 edition 8.1970 → replaced by edition 1.1988
Fireproof building materials · Fireproof rectangular bricks · Dimensions
DIN 1082 - Part 1 · Edition 3.2017 → current
Ceramic refractory products · Dimensions · Fireproof vaulted stones
The standard specifies dimensions and designations for refractory vaulted stones with lengths of 114 mm, 124 mm, 172 mm, 230 mm and 250 mm.
DIN 1082 - Part 1 · Edition 1.1988 → replaced by Edition 3.2017
Ceramic refractory materials · Fireproof vaulted stones · Dimensions
The standard specifies dimensions for refractory vaulted stones.
DIN 1082 - Part 2 · Edition 3.2017 → current
Ceramic refractory products · Dimensions · Refractory abutment bricks
The standard specifies dimensions and designations for refractory abutment bricks with a wedge dimension of 76 mm.
DIN 1082 - Part 2 · Edition 1.1988 → replaced by Edition 3.2017
Ceramic refractory materials · Refractory abutment bricks · Dimensions
The standard specifies dimensions for refractory abutment bricks.
DIN 1082 - Part 3 · Edition 3.2017 → current
Ceramic refractory products · Dimensions · Basic vaulted stones and rectangular stones for converters and electric arc furnaces
The standard specifies dimensions and designations for basic vaulted and rectangular stones with lining thicknesses of 250 mm to 800 mm, as used in oxygen steel converters and in electric arc furnaces.
DIN 1082 - Part 3 · Edition 1.1988 → replaced by Edition 3.2017
Ceramic refractory materials · Basic vaulted stones and rectangular stones for converters and electric arc furnaces · Dimensions
The standard specifies dimensions for refractory, basic vaulted bricks and rectangular bricks for use in converters and electric arc furnaces.
DIN 1082 - Part 4 Edition 1.2007 → current
Ceramic refractory materials · Vaulted stones for use in rotary kilns · Dimensions
The standard specifies dimensions for refractory vaulted stones for use in rotary kilns.
DIN 1082 - part 4 edition 2.1989 → replaced by edition 1.2007
Ceramic refractory materials · Vaulted stones for rotary kilns · Dimensions
DIN 1082 edition 8.1970 → replaced by DIN 1082 part 1 edition 1.1988
Fireproof building materials · Fireproof half vault and full vault · Dimensions
DIN 1089 - Part 1 · Edition 2.1995 → current
Refractory materials for coke ovens · Silica bricks · Requirements and testing
DIN 1089 - Part 1 · Edition 8.1986 → replaced by Edition 2.1995
Refractory materials for coke ovens · Silica bricks · Requirements and testing
DIN 1089 - Part 1 edition 11.1970 → replaced by edition 8.1986
Refractory building materials · Coke oven bricks, lime-bound silica bricks, requirements and testing
DIN 1089 - Part 2 · Edition 2.1995 → current
Refractory materials for coke ovens · Firebricks · Requirements and testing
DIN 1089 - Part 2 · Edition 8.1986 → replaced by Edition 2.1995
Refractory materials for coke ovens · Quartz fireclay bricks · Requirements and testing
DIN 1089 - Part 2 · Edition 12.1956 → replaced by Edition 8.1986
Refractory building materials · Coke oven bricks, quality values of quartz fire bricks
DIN 1089 - Part 3 Edition 10.1990 → current
Refractory materials for coke ovens · Mortars for silica and firebricks · Requirements and testing
DIN 1100 · Edition 5.2004 → current
Hard aggregates for cement-bound hard aggregate screeds · Requirements and test methods
This standard applies to hard materials that are used in the wear layer of cement-bound hard aggregate screeds according to DIN 18560 Part 7 and that increase the wear resistance of the screed. It also applies to hard materials that are used for scattering on cement-bound screeds, e.g. B. according to DIN 18560 part 3 and part 4, can be used to increase the resistance to wear.
DIN 1100 edition 10.1989 → replaced by edition 5.2004
Hard aggregates for cement-bound hard aggregate screeds
DIN 1100 edition 5.1979 → replaced by edition 10.1989
Hard aggregates for cement-bound hard aggregate screeds
DIN 1101 Edition 6.2000 → withdrawn
Wood wool lightweight panels and multilayer lightweight panels as insulating materials for the building industry · Requirements, testing
DIN 1101 edition 11.1989 → replaced by edition 6.2000 as well as DIN EN 822, DIN EN 823 and DIN EN 824 edition 11.1994 as well as DIN EN 826 edition 5.1996 and DIN EN 1602 edition 1.1997 and DIN EN 1607 edition 1.1997 and DIN EN 12089 edition 8.1997
Wood wool lightweight panels and multilayer lightweight panels as insulating materials for the building industry · Requirements, testing
DIN 1101 edition 3.1980 → replaced by edition 11.1989
Wood wool lightweight panels · Dimensions, requirements, testing
DIN 1101 edition 4.1970 → replaced by edition 3.1980
Wood wool lightweight panels · Dimensions, requirements, testing
DIN 1102 edition 11.1989 → withdrawn
Wood wool lightweight panels and multi-layer lightweight panels according to DIN 1101 as insulation materials for the building industry · Use, processing
The application of DIN 4108 part 10 edition 6.2008 is recommended.
DIN 1102 edition 3.1980 → replaced by edition 11.1989
Wood wool lightweight panels according to DIN 1101 · Processing
DIN 1104 - Part 1 edition 3.1980 → replaced by DIN 1101 edition 11.1989
Multi-layer lightweight panels made of foam plastics and wood wool · Dimensions, requirements, testing
DIN 1104 - Part 2 edition 3.1980 → replaced by DIN 1102 edition 11.1989
Multi-layer lightweight panels made of foam plastics and wood wool · Processing
DIN 1143 - Part 1 Edition 8.1982 → current
Machine pins, round, loose
DIN 1157 edition 4.1973 → current
Upholstery pens
DIN 1158 edition 4.1973 → current
Hook pins
DIN 1159 edition 4.1973 → current
Loops with lace cut on one side
DIN 1163 · Edition 4.1973 → current
Shaping pins
DIN 1164 - Part 10 · Edition 3.2013 → current
Cement with special properties · Composition, requirements and proof of conformity of cement with a low effective alkali content
DIN 1164 - Part 10 - Correction 1 · Edition 1.2005 → replaced by DIN 1164 Part 10 Edition 3.2013
Cement with special properties · Composition, requirements and proof of conformity of normal cement with special properties · Corrections to DIN 1164-10: 2004-08
DIN 1164 - Part 10 · Edition 8.2004 → replaced by Edition 3.2013
Cement with special properties · Composition, requirements and proof of conformity of normal cement with special properties
DIN 1164 - Part 11 · Edition 11.2003 → current
Cement with special properties · Composition, requirements and proof of conformity of cement with reduced setting
DIN 1164 - Part 12 · Edition 6.2005 → current
Cement with special properties · Composition, requirements and proof of conformity of cement with an increased proportion of organic components
DIN 1164 edition 11.2000 → replaced by DIN 1164 part 10 edition 8.2004 and DIN EN 197 part 1 edition 8.2004
Cement with special properties · Composition, requirements, proof of conformity
DIN 1164 - Part 1 - Amendment A1 · Edition 1.1999 → replaced by DIN 1164 Edition 11.2000
Cement · Composition, requirements · Amendment A1
DIN 1164 - part 1 edition 10.1994 → replaced by DIN 1164 edition 11.2000 and DIN EN 197 part 1 edition 11.2000
Cement · Composition, requirements
DIN 1164 - part 1 edition 10.1994 → replaced by DIN 1164 edition 11.2000 and DIN EN 197 part 1 edition 11.2000
Cement · Composition, requirements
DIN 1164 - Part 1 · Edition 3.1990 → replaced by Edition 10.1994
Portland, iron Portland, blast furnace and trass cement · Terms, components, requirements, delivery
DIN 1164 - Part 1 · Edition 12.1986 → replaced by Edition 3.1990
Portland, iron Portland, blast furnace and trass cement · Terms, components, requirements, delivery
DIN 1164 - part 1 edition 11.1978 → replaced by edition 12.1986
Portland, iron Portland, blast furnace and trass cement · Terms, components, requirements, delivery
DIN 1164 - part 2 edition 11.1996 → replaced by DIN 1164 edition 11.2000 and DIN EN 197 part 1 edition 11.2000
Cement · Certificate of Conformity
DIN 1164 - part 2 edition 3.1990 → replaced by edition 11.1996
Portland, iron portland, blast furnace and trass cement monitoring (quality monitoring)
DIN 1164 - Part 2 edition 11.1978 → replaced by edition 3.1990
Portland, iron portland, blast furnace and trass cement monitoring (quality monitoring)
DIN 1164 - part 100 edition 3.1990 → replaced by DIN 1164 part 1 edition 10.1994
Cement · Portland oil shale cement · Requirements, tests, monitoring
DIN 1164 - part 100 edition 1.1989 → replaced by edition 3.1990
Cement · Portland oil shale cement · Requirements, tests, monitoring
DIN 1180 edition 11.1971 → withdrawn
Clay drainage pipes · Dimensions, requirements, testing
DIN 1184 - Part 1 · Edition 3.1992 → current
Pumping stations / pumping stations · Planning, construction and operation
DIN 1184 - Part 1 · Edition 1.1963 → replaced by Edition 3.1992
Pumping stations / pumping stations · Planning, construction and operation
DIN 1184 - Part 2 · Edition 3.1992 → current
Pumping stations / pumping stations · Centrifugal pumps for operation with rakes · Guidelines for planning
DIN 1184 - Part 3 · Edition 3.1992 → current
Pumping stations / pumping stations · Centrifugal pumps for operation without rake · Guidelines for planning
DIN 1184 - Part 4 Edition 3.1992 → current
Pumping stations / pumping stations · Screw trough pumps (water screws) · Guidelines for planning
DIN 1184 edition 1.1963 → replaced by DIN 1184 parts 1, 2 and 3 edition 3.1992
Buckets · Basics and guidelines for planning
DIN 1185 - Part 1 · Edition 12.2015 → current
Drainage · Regulation of the soil water balance through pipe drainage and subsoil improvement · General principles
The standard contains an overview of the current options for regulating the soil water balance, taking into account the specific site conditions, with special consideration of the newly included subsoil improvement.
DIN 1185 - Part 1 edition 12.1973 → replaced by edition 12.2015
Drainage · Regulation of the soil water balance through pipe drainage, non-pipe drainage and subsoil improvement · General information and special cases
DIN 1185 - Part 2 · Edition 12.2015 → current
Drainage · Regulation of the soil water balance through pipe drainage and subsoil improvement · Planning and dimensioning
The standard applies to the planning and dimensioning of drainage systems to regulate the soil water balance in areas used for agriculture, with the exception of areas with trees.
DIN 1185 - part 2 edition 12.1973 → replaced by edition 12.2015
Drainage · Regulation of the soil water balance through pipe drainage, non-pipe drainage and subsoil improvement · Essential information for planning and dimensioning
DIN 1185 - Part 3 · Edition 12.2015 → current
Drainage · Regulation of the soil water balance through pipe drainage and subsoil improvement · Execution and documentation
The standard defines the principles necessary to build a drainage. It applies to the regulation of the soil water balance of agriculturally used areas with the exception of areas with trees.
DIN 1185 - Part 3 · Edition 12.1973 → replaced by Edition 12.2015
Drainage · Regulation of the soil water balance through pipe drainage, non-pipe drainage and subsoil improvement · Execution
DIN 1185 - part 4 edition 12.1973 → replaced by DIN 1185 part 3 edition 12.2015
Drainage · Regulation of the soil water balance by means of pipe drainage, pipeless drainage and subsoil improvement · Draft and existing drawings
DIN 1185 - Part 5 Edition 12.1973 → replaced by DIN 1185 Part 1 Edition 12.2015
Drainage · Regulation of the soil water balance through pipe drainage, non-pipe drainage and subsoil improvement · Maintenance
DIN 1187 edition 11.1982 → current
Drainage pipes made of plasticizer-free polyvinyl chloride (hard PVC) · Dimensions, requirements, tests
DIN 1193 edition 2.2012 → current
Steel hammers · Technical delivery conditions
DIN 1193 · Edition 8.2006 → replaced by Edition 2.2012
Steel hammers · Technical delivery conditions
DIN 1193 edition 9.2000 → replaced by edition 8.2006
Steel hammers · Technical delivery conditions
DIN 1193 edition 12.1991 → replaced by edition 9.2000
Steel hammers · Technical delivery conditions
DIN 1193 edition 1.1982 → replaced by edition 12.1991
Steel hammers · Technical delivery conditions
DIN 1195 edition 2.2007 → current
Eye dimensions for hammers and forging tools
The standard applies to standardized and non-standardized hand hammers made of steel and for forging tools, unless otherwise specified in individual other standards.
DIN 1195 edition 12.1991 → replaced by edition 2.2007
Eye dimensions for hammers and forging tools
DIN 1195 edition 11.1966 → replaced by edition 12.1991
Eye dimensions for hammers and forging tools
DIN 1197 - Part 1 · Edition 6.1990 → current
Hoe eyes, oval · Dimensions, requirements, testing
DIN 1197 - Part 1 · Edition 10.1970 → replaced by Edition 6.1990
Hoe eyes, oval · Dimensions, requirements, testing
DIN 1197 - Part 2 · Edition 6.1990 → current
Hook eyes, oval · plug gauges
DIN 1197 edition 10.1970 → replaced by DIN 1197 parts 1 and 2 edition 6.1990
Hoe eyes, oval · Plug gauges for hoe eyes
DIN 1211 - Part 1 · Edition 5.2003 → current
Crampons for double-barreled crampons · Crampons for walling in or setting in concrete
DIN 1211 - Part 1 edition 10.1986 → replaced by edition 5.2003
Crampons for double-barreled crampons · Crampons for walling in or setting in concrete
DIN 1211 - Part 1 edition 11.1982 → replaced by edition 10.1986
Crampons, short
DIN 1211 - Part 2 · Edition 5.2003 → current
Crampons for two-way crampons · Crampons for installation in precast concrete parts
DIN 1211 - Part 2 edition 10.1986 → replaced by edition 5.2003
Crampons for two-way crampons · Crampons for installation in precast concrete elements
DIN 1211 - Part 3 · Edition 4.2010 → current
Crampons for two-barrel crampons · Crampons for screwing on and through
DIN 1211 - Part 3 · Edition 5.2003 → replaced by Edition 4.2010
Crampons for two-barrel crampons · Crampons for screwing on and through
DIN 1212 - Part 1 · Edition 5.2003 → current
Crampons with upstand for two-way crampons · Crampons for walling in or setting in concrete
DIN 1212 - Part 1 · Edition 10.1986 → replaced by Edition 5.2003
Crampons for two-way crampons · Crampons with upstand for walling in or setting in concrete
DIN 1212 - Part 2 · Edition 5.2003 → current
Crampons with upstand for two-way crampons · Crampons for installation in precast concrete parts
DIN 1212 - Part 2 · Edition 10.1986 → replaced by Edition 5.2003
Crampons for two-way crampons · Crampons with upstand for installation in precast concrete elements
DIN 1212 - Part 3 · Edition 4.2010 → current
Crampons with upstand for two-way crampons · Crampons for screwing on and through
DIN 1212 - Part 3 · Edition 5.2003 → replaced by Edition 4.2010
Crampons with upstand for two-way crampons · Crampons for screwing on and through
DIN 1213 - Part 1 · Edition 5.1973 → replaced by DIN 1229 Edition 3.1986 and DIN EN 124 Edition 6.1986
Attachments for street and yard drains · Classification, building principles, labeling
DIN 1213 - Part 2 · Edition 5.1973 → replaced by DIN 1229 Edition 3.1986 and DIN EN 124 Edition 6.1986
Attachments for street and yard processes · Testing, quality monitoring
DIN 1221 edition 2.1992 → current
Dirt trap for manhole covers
DIN 1221 edition 11.1973 → replaced by edition 2.1992
Dirt trap for manhole covers
DIN 1229 edition 9.2015 → current
Attachments and covers for traffic areas · Securing the lid or grate in the frame
The standard applies together with DIN EN 124 parts 1 to 6 for attachments and covers of drainage systems with a clear width of up to and including 1000 mm that are subject to the stresses in traffic areas or comparable stresses.
DIN 1229 edition 6.1996 → replaced by edition 9.2015
Standard weights for attachments and covers for traffic areas
DIN 1229 edition 3.1986 → replaced by edition 6.1996
Attachments and covers for traffic areas · Classification, building principles, testing, monitoring and marking
DIN 1229 - Part 1 · Edition 5.1973 → replaced by DIN 1229 Edition 3.1986 and DIN EN 124 Edition 6.1986
Manhole covers for drainage systems · Classification, building principles, labeling
DIN 1229 - Part 2 · Edition 5.1973 → replaced by DIN 1229 Edition 3.1986 and DIN EN 124 Edition 6.1986
Manhole covers for drainage systems · Testing, quality monitoring
DIN 1236 - Part 1 Edition 11.1981 → current
Concrete parts and buckets for drains · Classes A and B · Design, installation and combinations
DIN 1236 - Part 2 Edition 11.1981 → current
Concrete parts and buckets for drains · Classes A and B · Concrete parts
DIN 1236 - Part 3 Edition 11.1981 → current
Concrete parts and buckets for drains · Classes A and B · Buckets
DIN 1239 edition 2.1999 → current
Manhole covers for wells, spring sockets and other water supply structures · Building principles
DIN 1239 - Part 1 · Edition 6.1963 → replaced by DIN 1239 Edition 2.1999
Manhole covers for well shafts and spring sockets · Assemblies
DIN 1239 - Part 2 · Edition 6.1963 → replaced by DIN 1239 Edition 2.1999
Manhole covers for well shafts and spring sockets · Frames
DIN 1239 - Part 3 · Edition 6.1963 → replaced by DIN 1239 Edition 2.1999
Manhole covers for well shafts and spring sockets · Lid without ventilation
DIN 1239 - Part 4 Edition 6.1963 → replaced by DIN 1239 Edition 2.1999
Manhole covers for well shafts and spring sockets · Lid with ventilation
DIN 1239 - Part 5 · Edition 6.1963 → replaced by DIN 1239 Edition 2.1999
Manhole covers for well shafts and spring sockets · Individual parts
DIN 1249 - Part 11 · Edition 5.2017 → current
Flat glass in construction · Glass edges · Terms, edge shapes and execution
The standard specifies various edge shapes and their design types, from flat glass used in construction.
DIN 1249 - part 11 edition 9.1986 → replaced by edition 5.2017
Flat glass in construction · Glass edges · Concept, edge shapes and execution
DIN 1259 - Part 1 Edition 9.2001 → current
Glass · Terms for types and groups of glass
DIN 1259 - Part 1 edition 9.1986 → replaced by edition 9.2001
Glass · Terms for types and groups of glass
DIN 1259 - Part 1 · Edition 7.1971 → replaced by Edition 9.1986
Glass · Terms for types of glass
DIN 1259 - Part 2 Edition 9.2001 → current
Glass · Terms for glass products
DIN 1259 - Part 2 Edition 9.1986 → replaced by Edition 9.2001
Glass · Terms for glass products
DIN 1259 - Part 2 · Edition 7.1971 → replaced by Edition 9.1986
Glass · Terms for glass products
DIN 1282 edition 11.1990 → current
Lubricating presses · push press
DIN 1282 edition 6.1972 → replaced by edition 11.1990
Lubricating presses · push press
DIN 1283 edition 11.1990 → current
Lubricating presses · Hand lever press and accessories
DIN 1283 edition 3.1973 → replaced by edition 11.1990
Lubricating presses · Hand lever press and accessories
DIN 1284 edition 11.1990 → current
Grease guns · Grease cartridges for hand lever presses · Main dimensions
DIN 1284 edition 5.1972 → replaced by edition 11.1990
Grease guns · Grease cartridges (empty) for hand lever presses · Main dimensions
DIN 1289 edition 4.1928 → current
Fire cupboard for tiled stoves · Filling door for filling firing
DIN 1298 edition 8.2015 → current
Exhaust systems · Connection pieces for combustion systems · Pipes and fittings made of metal for exhaust gases from domestic fireplaces in negative pressure operation
DIN 1298 edition 8.2008 → replaced by edition 8.2015
Exhaust systems · Connection pieces for combustion systems · Pipes and fittings made of metal for exhaust gases from domestic fireplaces in negative pressure operation
DIN 1298 edition 7.1978 → replaced by edition 8.2008 and DIN EN 1856 part 2 edition 10.2004
Connection pieces for combustion systems · Pipes, pipe elbows and pipe bends made of metal, for exhaust gases
DIN 1301 - Part 1 · Edition 10.2010 → current
Units · Unit names, unit symbols
The standard contains the units of the International System of Units (SI) and some other recommended units as well as the prefixes for decimal parts and multiples of these units.
DIN 1301 - Part 1 · Edition 10.2002 → replaced by Edition 10.2010
Units · Unit names, unit symbols
DIN 1301 - Part 1 edition 12.1993 → replaced by edition 10.2002
Units · Unit names, unit symbols
DIN 1301 - Part 1 edition 12.1985 → replaced by edition 12.1993
Units · Unit names, unit symbols
DIN 1301 - Part 1 · Edition 10.1978 → replaced by Edition 12.1985
Units · Unit names, unit symbols
DIN 1301 - Part 1 - Supplement 1 · Edition 4.1982 → current
Units · Unit-like names and characters
DIN 1301 - Part 2 Edition 2.1978 → current
Units · Commonly used parts and multiples
DIN 1301 - Part 3 Edition 10.1979 → current
Units · Conversions for units that are no longer applicable
DIN 1302 edition 12.1999 → current
General mathematical signs and terms
DIN 1302 edition 4.1994 → replaced by edition 12.1999
General mathematical signs and terms
DIN 1302 edition 8.1980 → replaced by edition 4.1994
General mathematical signs and terms
DIN 1303 Edition 3.1987 → current
Vectors, matrices, tensors · Signs and concepts
DIN 1303 edition 8.1959 → replaced by edition 3.1987
Notation of tensors (vectors)
DIN 1304 - Part 1 · Edition 3.1994 → current
Formula symbols · General formula symbols
DIN 1304 - Part 1 · Edition 3.1989 → replaced by Edition 3.1994
Formula symbols · General formula symbols
DIN 1304 - Part 2 Edition 9.1989 → current
Formula symbols · Formula symbols for meteorology and geophysics
DIN 1304 - Part 5 Edition 9.1989 → current
Formula symbols · Formula symbols for fluid mechanics
DIN 1304 - Part 8 Edition 2.1994 → current
Formula symbol · Formula symbol for converters with semiconductor components
DIN 1304 - Part 9 Edition 1.2003 → current
Formula symbols · Formula symbols for equivalent circuit diagrams for quartz oscillators
DIN 1304 edition 2.1978 → replaced by DIN 1304 part 1 edition 3.1989
General formula symbols
DIN 1305 edition 1.1988 → current
Mass, weight, force, weight, weight, load · Terms
DIN 1305 edition 5.1977 → replaced by edition 1.1988
Mass, force, weight, weight, load · Terms
DIN 1306 Edition 6.1984 → current
Density · Terms, information
DIN 1306 edition 12.1971 → replaced by edition 6.1984
Density · Terms
DIN 1310 edition 2.1984 → current
Composition of mixed phases (gas mixtures, solutions, mixed crystals) · Terms, symbols
DIN 1310 edition 12.1979 → replaced by edition 2.1984
Composition of mixed phases (gas mixtures, solutions, mixed crystals) · Terms, symbols
DIN 1311 - Supplement 2 Edition 3.2002 → current
Vibrations and vibratory systems · Dictionary
DIN 1311 - Part 1 · Edition 2.2000 → current
Vibrations and systems capable of vibrating · Basic terms, classification
DIN 1311 - Part 1 · Edition 2.1974 → replaced by Edition 2.2000
Oscillation theory · Kinematic terms
DIN 1311 - Part 2 Edition 8.2002 → current
Vibrations and vibratory systems · Linear, time-invariant vibratory systems with one degree of freedom
DIN 1311 - part 2 edition 12.1974 → replaced by edition 8.2002
Oscillation theory · Simple oscillators
DIN 1311 - Part 3 · Edition 2.2000 → current
Oscillations and oscillatory systems · Linear, time-invariant oscillatory systems with a finite number of degrees of freedom
DIN 1311 - part 3 edition 12.1974 → replaced by edition 2.2000
Vibration theory · Vibration systems with a finite number of degrees of freedom
DIN 1311 - Part 4 Edition 2.1974 → current
Oscillation theory · Oscillating continua, waves
DIN 1312 edition 3.1972 → current
Geometric orientation
DIN 1313 edition 12.1998 → current
Sizes
DIN 1313 edition 4.1978 → replaced by edition 12.1998
Physical quantities and equations · Terms, notations
DIN 1314 edition 2.1977 → current
Pressure · Basic concepts, units
DIN 1315 edition 8.1982 → current
Angle · Terms, units
DIN 1317 - Part 1 · Edition 3.1957 → current
Standard pitch · Standard pitch
DIN 1317 - Part 2 Edition 8.1959 → withdrawn
Standard tuning tone · tuning fork
DIN 1317 - Part 3 · Edition 6.1962 → current
Standard tuning tone · Tuning tone of the organ
DIN 1318 edition 9.1970 → current
Volume level · Terms, measurement methods
DIN 1319 - Part 1 Edition 1.1995 → current
Basics of measurement technology · Basic terms
DIN 1319 - Part 1 · Edition 6.1985 → replaced by Edition 1.1995
Basic terms in measurement technology · General basic terms
DIN 1319 - Part 1 edition 11.1971 → replaced by edition 6.1985
Basic terms of measurement technology · Measure, count, test
DIN 1319 - Part 2 Edition 10.2005 → current
Basics of measuring technology · Terms for measuring equipment
DIN 1319 - part 2 edition 1.1980 → replaced by edition 10.2005 and DIN 1319 part 1 edition 1.1995
Basic terms in measuring technology · Terms for the use of measuring devices
DIN 1319 - Part 3 · Edition 5.1996 → current
Basics of measurement technology · Evaluation of measurements of a single measured variable, measurement uncertainty
DIN 1319 - Part 3 Edition 8.1983 → replaced by Edition 5.1996 and DIN 1319 Part 1 Edition 1.1995
Basic terms of measurement technology · Terms for the measurement uncertainty and for the assessment of measuring devices and measuring devices
DIN 1319 - Part 3 · Edition 1.1972 → replaced by Edition 8.1983
Basic terms of measurement technology · Terms for the measurement uncertainty and for the assessment of measuring devices and measuring devices
DIN 1319 - Part 4 Edition 2.1999 → current
Basics of measurement technology · Evaluation of measurements · Measurement uncertainty
DIN 1319 - Part 4 Edition 12.1985 → replaced by Edition 2.1999
Basic terms of measurement technology · Handling of uncertainties in the evaluation of measurements
DIN 1320 · Edition 12.2009 → current
Acoustics · Terms
The standard defines acoustics terms and their names. Most of the terms were taken from the IEC 60050-801 standard.
DIN 1320 · Edition 6.1997 → replaced by Edition 12.2009
Acoustics · Terms
DIN 1320 · Edition 6.1992 → replaced by Edition 6.1997
Acoustics · Terms
DIN 1320 edition 10.1969 → replaced by edition 6.1992
Acoustics · Basic concepts
DIN 1323 Edition 2.1966 → replaced by DIN 1324 Part 1 Edition 5.1988 and DIN 5489 Edition 9.1990
Acoustics · Terms
The standard defines acoustics terms and their names. Most of the terms were taken from the IEC 60050-801 standard.
DIN 1324 - Part 1 · Edition 5.2017 → current
Electromagnetic field · State variables
The standard represents the state variables of the electromagnetic field individually defined in Part 121 of the International Electrotechnical Dictionary (IEV).
DIN 1324 - Part 1 edition 5.1988 → replaced by edition 5.2017
Electromagnetic field · State variables
DIN 1324 - Part 2 · Edition 5.1988 → current
Electromagnetic field · Material sizes
DIN 1324 - Part 3 · Edition 5.1988 → current
Electromagnetic field · Electromagnetic waves
DIN 1324 edition 1.1972 → replaced by DIN 1324 parts 1 and 2 edition 5.1988
Electric field · Terms
DIN 1325 edition 1.1972 → replaced by DIN 1324 parts 1 and 2 edition 5.1988
Magnetic field · Terms
DIN 1326 - Part 1 Edition 10.1991 → current
Plasmas · Physical basics
DIN 1326 - Part 1 · Edition 7.1971 → replaced by Edition 10.1991
Gas discharges, stationary discharges · Terms
DIN 1332 edition 10.1969 → replaced by DIN EN ISO 80000 part 8 edition 1.2008
Acoustics · Formula symbols
DIN 1333 edition 2.1992 → current
Numbers
DIN 1333 - Part 1 · Edition 2.1972 → replaced by DIN 1333 Edition 2.1992
Numbers · Decimal notation
DIN 1333 - Part 2 · Edition 2.1972 → replaced by DIN 1333 Edition 2.1992
Numbers · Rounds
DIN 1335 · Edition 12.2003 → current
Geometric optics · Terms and definitions
DIN 1335 · Edition 6.1983 → replaced by Edition 12.2003
Technical ray optics in photography · Characters, names
DIN 1335 edition 7.1975 → replaced by edition 6.1983
Technical ray optics in photography · Characters, names
DIN 1338 Edition 3.2011 → current
Formula notation and formula set
The standard applies to the spelling and the set of mathematical, physical and chemical formulas in science and technology.
DIN 1338 edition 8.1996 → replaced by edition 3.2011
Formula notation and formula set
DIN 1338 edition 7.1977 → replaced by edition 8.1996
Formula notation and formula set
DIN 1338 - supplement 1 edition 4.1996 → replaced by DIN 1338 edition 3.2011
Formula notation and formula set · Form of the characters
DIN 1338 - supplement 1 edition 5.1980 → replaces edition 4.1996
Formula notation and formula set · Form of the characters
DIN 1339 edition 11.1971 → withdrawn
Units of magnetic quantities
DIN 1339 edition 7.1946 → withdrawn
Magnetic units
DIN 1340 edition 12.1990 → current
Gaseous fuels and other gases · Types, components, use
DIN 1340 - supplement 1 edition 12.1990 → current
Gaseous fuels and other gases · Types, components, use · Comments on generation
DIN 1340 edition 12.1984 → replaced by edition 12.1990
Gaseous fuels and other gases · Types, components, use
DIN 1340 - supplement 1 edition 12.1984 → replaced by edition 12.1990
Gaseous fuels and other gases · Types, components, use · Comments on generation
DIN 1340 edition 9.1975 → replaced by edition 12.1984
Fuel gases · types, components, use
DIN 1340 - supplement 1 edition 9.1975 → replaced by edition 12.1984
Fuel gases · Types, components, use, comments on generation
DIN 1341 Edition 10.1986 → current
Heat transfer · Terms, parameters
DIN 1341 edition 11.1971 → replaced by edition 10.1986
Heat transfer · Basic terms, units, parameters
DIN 1342 - Part 1 · Edition 11.2003 → current
Viscosity · Rheological terms
DIN 1342 - Part 1 · Edition 10.1983 → replaced by Edition 11.2003
Viscosity · Rheological terms
DIN 1342 - Part 2 · Edition 11.2003 → current
Viscosity · Newtonian fluids
DIN 1342 - Part 2 · Edition 2.1986 → replaced by Edition 11.2003
Viscosity · Newtonian fluids
DIN 1342 - Part 3 · Edition 11.2003 → current
Viscosity · Non-Newtonian fluids
DIN 1342 edition 12.1971 → replaced by DIN 1342 part 2 edition 2.1986
Viscosity of Newtonian fluids
DIN 1343 Edition 1.1990 → current
Reference condition, standard condition, standard volume · Terms and values
DIN 1343 edition 8.1986 → replaced by edition 1.1990
Reference condition, standard condition, standard volume · Terms and values
DIN 1343 edition 11.1975 → replaced by edition 8.1986
Standard condition, standard volume
DIN 1345 edition 12.1993 → current
Thermodynamics · Basic Terms
DIN 1345 edition 9.1975 → replaced by edition 12.1993
Thermodynamics · Symbols, units
DIN 1349 - Part 1 · Edition 6.1972 → current
Transmission of optical radiation through media · Optically clear substances · Sizes, symbols and units
DIN 1349 - Part 2 · Edition 4.1975 → current
Transmission of optical radiation through media · Visually cloudy substances · Terms
DIN 1353 - Part 1 edition 4.1971 → replaced by DIN ISO 5261 edition 4.1997
Abbreviations of terms · Elementary abbreviations
DIN 1353 - Part 2 · Edition 4.1971 → replaced by DIN ISO 5261 Edition 4.1997
Abbreviations of names for semi-finished products
DIN 1355 - Part 1 Issue 3.1975 → withdrawn
Time · Calendar, week numbering, current date, time
DIN 1356 - Part 1 · Edition 2.1995 → current
Construction drawings · Types, contents and basic rules of representation
DIN 1356 - Part 6 · Edition 5.2006 → current
Technical product documentation · Construction drawings · Construction drawings
The standard specifies requirements for construction drawings.
DIN 1356 Edition 7.1974 → replaced by DIN 1356 Part 1 Edition 2.1995
Architectural drawings
DIN 1357 edition 11.1971 → withdrawn
Units of electrical quantities
DIN 1367 - Part 1 Edition 8.1974 → current
Sealing wires made of galvanized steel wire
DIN 1380 Edition 5.2001 → current
Urinal connection pieces · Requirements and testing
DIN 1380 - part 1 edition 1.1982 → replaced by DIN 1380 edition 5.2001
Urinal connection pieces · Dimensions
DIN 1380 - Part 2 Edition 1.1982 → replaced by DIN 1380 Edition 5.2001
Urinal connection pieces · Construction and testing principles
DIN 1389 · Edition 12.2015 → current
Toilet connectors · Requirements and testing
The standard specifies requirements for dimensions, materials, function and interchangeability of toilet connectors and their testing. It applies to toilet connection pieces of sizes DN 80 and DN 100 for the connection of toilet bowls with connection dimensions according to DIN EN 33 with the connection line of the drainage system of the building according to DIN 1986 Part 100 and the series DIN EN 12056 and according to official notification.
DIN 1389 edition 5.2001 → replaced by edition 12.2015
Toilet connectors · Requirements and testing
DIN 1389 - Part 1 edition 11.1975 → replaced by DIN 1389 edition 5.2001
Toilet connectors · Dimensions
DIN 1389 - Part 2 Edition 10.1979 → replaced by DIN 1389 Edition 5.2001
Toilet connection pieces · Construction and testing principles
DIN 1409 Edition 7.2000 → current
Broaching tools made of high-speed steel · Technical delivery conditions
DIN 1409 edition 7.1997 → replaced by edition 7.2000
Broach tool made of high-speed steel · Technical delivery conditions
DIN 1410 · Edition 6.1986 → current
Machine tools · Direction of movement and arrangement of the controls
DIN 1410 edition 2.1956 → replaced by edition 6.1986
Machine tools · Direction of movement and arrangement of controls, general provisions
DIN 1412 edition 3.2001 → current
Twist drill made of high-speed steel · Bevel shapes
DIN 1412 edition 12.1966 → replaced by edition 3.2001 and DIN ISO 5419 edition 6.1998
Twist drill · Terms
DIN 1414 - Part 1 · Edition 11.2006 → current
Technical delivery conditions for twist drills made of high-speed steel · Requirements
The standard contains requirements for standardized two-flute twist drills made of high-speed steel.
DIN 1414 - Part 1 · Edition 6.1998 → replaced by Edition 11.2006
Technical delivery conditions for twist drills made of high-speed steel · Requirements
DIN 1414 - Part 2 · Edition 6.1998 → current
Technical delivery conditions for twist drills made of high-speed steel · Testing
DIN 1414 edition 10.1977 → replaced by DIN 1414 parts 1 and 2 edition 6.1998
Twist drill made of high-speed steel · Technical delivery conditions
DIN 1415 - Part 1 Edition 9.1973 → current
Broaching tools · Classification, names, types
DIN 1415 - Part 3 Edition 8.1970 → current
Broaching Tools · Round Shanks A and B
DIN 1415 - Part 4 Edition 8.1970 → current
Broaching tools · Round end pieces C and D
DIN 1415 - Part 5 Edition 8.1970 → current
Broaching tools Rectangular shanks E and end pieces F (not for hub grooves)
DIN 1415 - Part 6 Edition 8.1970 → current
Broaching tools Rectangular shanks G with straight driving surface (for hub grooves)
DIN 1416 edition 11.1971 → current
Broaching tools · Design of cutting tooth and chip space
DIN 1417 - Part 1 Edition 8.1970 → current
Broaching tools · Round shafts J and K with angled driving surface
DIN 1417 - Part 2 Edition 8.1970 → current
Broaching tools · Round end pieces L and M
DIN 1417 - Part 3 Edition 8.1970 → current
Broaching tools Rectangular shanks N with inclined driving surface (not for hub grooves)
DIN 1417 - Part 4 Edition 8.1970 → current
Broaching tools Rectangular end pieces P (not for hub grooves)
DIN 1417 - Part 5 Edition 8.1970 → current
Broaching tools Rectangular shanks R with inclined driving surface (for hub grooves)
DIN 1417 - Part 6 Edition 8.1970 → current
Broaching tools Rectangular end pieces S (for hub grooves)
DIN 1418 - Part 1 Edition 8.1970 → current
Holder for broaching tools with shanks and end pieces according to DIN 1417 · Shank holder
DIN 1418 - Part 2 · Edition 1.1972 → current
Holder for broaching tools with shanks and end pieces according to DIN 1417 · End piece holder
DIN 1419 Edition 8.1970 → current
Internal broaching tools with interchangeable round broaching bushes · Main dimensions
DIN 1420 edition 11.1966 → current
Reamers · Manufacturing tolerances and designation
DIN 1421 edition 1.1983 → current
Structure and numbering in texts · Sections, paragraphs, lists
DIN 1422 - Part 1 · Edition 2.1983 → current
Publications from science, technology, economy and administration · Design of manuscripts and typescripts
DIN 1422 - Part 2 · Edition 4.1984 → withdrawn
Publications from science, technology, economy and administration · Design of fair copies for reprographic processes
DIN 1422 - Part 3 · Edition 4.1984 → withdrawn
Publications from science, technology, economy and administration · Typographical design
DIN 1422 - Part 4 Edition 8.1986 → current
Publications from science, technology, economy and administration · Design of research reports
DIN 1422 Edition 8.1952 → replaced by DIN 1422 Part 1 Edition 2.1983 and DIN 1422 Parts 2 and 3 Edition 4.1984
Technical and scientific publications · Guidelines for design
DIN 1426 edition 10.1988 → current
Contents of documents · Abstracts, literature reports
DIN 1426 edition 11.1973 → replaced by edition 10.1988
Contents in information and documentation
DIN 1434 edition 2.1977 → withdrawn
Bolts with small head, version w
DIN 1440 edition 7.1974 → replaced by DIN EN 28738 edition 10.1992
Washers, medium version, for bolts
DIN 1441 edition 8.2009 → current
Washers for bolts · Product class C
The standard specifies requirements for washers in rough design for bolts.
DIN 1441 edition 7.1974 → replaced by edition 8.2009
Washers, coarse, for bolts
DIN 1443 edition 3.1974 → replaced by DIN EN 22340 edition 10.1992
Bolts without head · Dimensions according to ISO
DIN 1444 edition 3.1974 → replaced by DIN EN 22341 edition 10.1992
Bolts with head · Dimensions according to ISO
DIN 1445 · Edition 2.2011 → current
Bolt with head and threaded pin
The standard applies to bolts with a head and threaded pin with a metric thread and constant bolt lengths with nominal diameters of 8 mm to 30 mm.
DIN 1445 edition 2.1977 → replaced by edition 2.2011
Bolt with head and threaded pin
DIN 1448 - Part 1 · Edition 1.1970 → current
Tapered shaft ends with external thread · Dimensions
DIN 1449 edition 1.1970 → current
Tapered shaft ends with internal thread Dimensions
DIN 1450 · Edition 4.2013 → current
Fonts · Legibility
The standard describes how fonts are displayed legibly.
DIN 1450 edition 7.1993 → replaced by edition 4.2013
Fonts · Legibility
DIN 1450 edition 2.1984 → replaced by edition 7.1993
Fonts · Legibility
DIN 1451 - Part 1 Edition 10.1998 → current
Fonts · Sans Serif Linear-Antiqua · General
DIN 1451 - Part 1 · Edition 5.1981 → replaced by Edition 10.1998
Fonts · Sans Serif Linear-Antiqua · General
DIN 1451 - Part 2 · Edition 2.1986 → current
Fonts · Sans Serif Linear Antiqua · Traffic Typeface
DIN 1451 - Part 2 · Edition 5.1980 → replaced by Edition 2.1986
Fonts · Sans Serif Linear-Antiqua · Typeface for traffic
DIN 1451 - Part 3 Edition 12.1987 → current
Fonts · Sans serif Linear-Antiqua · Fonts for lettering
DIN 1451 - Part 3 · Edition 5.1983 → replaced by Edition 12.1987
Fonts · Sans serif Linear-Antiqua · Fonts for lettering
DIN 1451 - Part 3 - Supplement 1 · Edition 12.1987 → current
Fonts · Sans serif linear antiqua · Printing · Akzidenz-Grotesk
DIN 1451 - Part 3 - Supplement 1 · Edition 5.1983 → replaced by Edition 12.1987
Fonts · Sans serif linear antiqua · Printing · Akzidenz-Grotesk
DIN 1451 - Part 3 - Supplement 2 Edition 12.1987 → current
Fonts · Sans Serif Linear Antiqua · Printing · Akzidenz-Grotesk-Buch
DIN 1451 - Part 3 - Supplement 2 · Edition 5.1983 → replaced by Edition 12.1987
Fonts · Sans Serif Linear Antiqua · Printing · Akzidenz-Grotesk-Buch
DIN 1451 - Part 3 - Supplement 3 Edition 12.1987 → current
Fonts · Sans Serif Linear-Antiqua · Printing · Helvetica
DIN 1451 - Part 3 - Supplement 3 · Edition 5.1983 → replaced by Edition 12.1987
Fonts · Sans Serif Linear-Antiqua · Printing · Helvetica
DIN 1451 - Part 3 - Supplement 4 · Edition 5.1983 → withdrawn
Fonts · Sans serif linear antiqua · Printed fonts · Noble grotesque
DIN 1451 - Part 4 Edition 8.1987 → current
Fonts · Sans serif linear antiqua · Stencil font for engraving and other processes
DIN 1455 edition 2.1974 → withdrawn
Manuscripts
DIN 1460 - Part 2 · Edition 10.2011 → current
Transcription of Cyrillic Alphabets · Transcription of Cyrillic alphabets of non-Slavic languages
The standard deals with the transliteration of Cyrillic characters from non-Slavic languages into the Latin alphabet.
DIN 1460 - Part 2 · Edition 3.2010 → replaced by Edition 10.2011
Transcription of Cyrillic Alphabets · Transcription of Cyrillic alphabets of non-Slavic languages
DIN 1460 edition 4.1982 → current
Transcription of Cyrillic alphabets of Slavic languages
DIN 1463 - Part 2 Edition 10.1993 → withdrawn
Creation and further development of thesauri · Multilingual thesauri
DIN 1463 - Part 1 Edition 11.1987 → withdrawn
Creation and further development of thesauri · Monolingual thesauri
DIN 1463 edition 3.1976 → replaced by DIN 1463 part 1 edition 11.1987
Guidelines for the creation and further development of thesauri
DIN 1464 edition 12.1976 → current
Loose-leaf editions (works) · Supplementary deliveries, form and classification
DIN 1469 · Edition 5.2012 → current
Grooved pins with neck
The standard applies to grooved pins with a neck with a nominal diameter of 1.5 mm to 25 mm.
DIN 1469 edition 2.2011 → replaced by edition 5.2012
Grooved pins with neck
DIN 1469 edition 11.1978 → replaced by edition 2.2011
Grooved pins with neck
DIN 1474 edition 11.1978 → replaced by DIN EN 28741 edition 10.1992
Grooved pins
DIN 1478 edition 9.2005 → current
Turnbuckle nuts made of tubular steel or round steel
The standard deals with turnbuckle nuts made of tubular steel or round steel. It contains information on dimensions, materials (steel, stainless steel), the threads, the coaxiality of the threaded holes, surface protection, connecting parts and the load capacity of the turnbuckle nuts.
DIN 1478 edition 9.1975 → replaced by edition 9.2005
Turnbuckles made of tubular steel or round steel
DIN 1479 edition 9.2005 → current
Hexagon turnbuckle nuts
DIN 1479 edition 2.1998 → replaced by edition 9.2005
Hexagon turnbuckle nuts
DIN 1479 edition 9.1975 → replaced by edition 2.1998
Turnbuckle nuts made of hexagonal steel
DIN 1480 edition 9.2005 → current
Turnbuckle nuts, forged (open form)
DIN 1480 edition 9.1975 → replaced by edition 9.2005 and DIN 34828 edition 9.2005
Turnbuckles, forged (open form)
DIN 1481 edition 11.1978 → replaced by DIN EN 28752 edition 8.1993
Dowel pins (clamping sleeves), heavy design
DIN 1495 - Part 1 · Edition 4.1983 → current
Sintered metal plain bearings with special requirements for small and micro electric motors · Spherical bearings, dimensions
DIN 1495 - Part 2 Edition 4.1983 → current
Sintered metal plain bearings with special requirements for small and micro electric motors · Cylinder bearings, dimensions
DIN 1495 - Part 3 Edition 3.1996 → current
Sintered metal plain bearings with special requirements for small and micro electric motors · Requirements and tests
DIN 1496 edition 3.1996 → current
Plain bearings · Determination of the operating behavior of precision-engineered plain bearings with the SLPG test device
DIN 1498 edition 8.1965 → current
Clamping bushes for bearings
DIN 1499 edition 8.1965 → current
Clamping bushes for bearings
See also
swell
- DIN standards committees (all valid, as well as new and withdrawn standards of the respective standards committee)
- Beuth Verlag - Product search
- Beuth Verlag - Search for historical documents (registration required)