Turning tool
![](https://upload.wikimedia.org/wikipedia/commons/thumb/a/af/LatheCarbideTippedBoringThreadingBars.jpg/220px-LatheCarbideTippedBoringThreadingBars.jpg)
Turning tools are cutting tools for the turning manufacturing process . They consist of a shaft that is clamped in the lathe , a cutting edge for machining the workpieces, and a tool body that connects the shaft and cutting edge. As a turning tool turning tools are referred to, in which the three components of a single continuous material (usually high-speed steel (HSS)) or their cutting edges are brazed onto the body (in this case mostly cutting of hard metal ). When the cutting edges are worn , they are reground ( tool grinding ). There are also clamp holders with which indexable inserts are clamped or screwed into the turning tool. Worn cutting boards are turned over to new edges for intervention to bring. When all possible edges are worn, a new plate is clamped and the old one thrown away. All turning tools are often referred to as turning tools.
With most turning tools, the shape of the work piece is created by the relative movement between the tool and the work piece. However, there are also tools that at least partially contain the shape of the workpiece as a negative. These include thread turning chisels, thread chasers and dies with which standardized threads can be produced. There are also profile turning tools for profile turning . These are mostly custom-made products in which the desired shape has been ground into the cutting edges from HSS or hard metal turning tools. There are turning tools for both external and internal machining. The latter are sometimes referred to as boring bars if they are particularly long.
High-speed steel turning tool
High- speed steel (HSS) turning tools consist of a single piece. They can consist of HSS throughout, with a tempered cutting edge, or the shank and base are made of simple steel with a welded-on cutting edge made of HSS. The shanks are rectangular or square for tools for external machining and round or polygonal for internal machining. An important differentiating feature for HSS turning tools is the base body: it can be straight, curved or offset from the shank. The shape of the cutting edge depends on the turning process: there are tools for facing, turning, threading or parting off.
Standards for turning tools made of HSS or carbide
The various forms are regulated in numerous standards. Usually the same shapes exist for tools made of HSS as well as those made of carbide. The standards for hard metal tools are given in brackets.
- Straight turning tool: DIN 4951 (4971)
- Curved turning tool: DIN 4952 (4972)
- Corner lathe chisel: DIN 4965 (4978)
- Stepped face lathe chisel: k. A. (4977)
- Stepped lathe chisel: DIN 4960 (4980)
- Wide turning tool: DIN 4956 (4976)
- pointed turning tool: DIN 4955 (4975)
- Grooving lathe chisel: DIN 4961 (4981)
- Internal lathe chisel: DIN 4953 (4973)
- Inside corner turning tool: DIN 4954 (4974)
- Inside chisel (also hook chisel): DIN 4963 (n / a)
Lathe chisel with brazed hard metal cutting edges
Lathe chisels with soldered carbide cutting edges are similar to those made of HSS. The forms and uses are basically the same. Cutting edges made of carbide are harder and more brittle. They are more wear-resistant, but more expensive. Therefore, the bodies are always made of a cheap material and only the cutting edges are made of hard metal. Worn cutting edges can be reground with grinding wheels made of diamond grain and synthetic resin bond. The hard metal turning tools are standardized in DIN 4982.
Clamp holder
Toolholders are turning tools into which an indexable insert is clamped or screwed as a cutting edge. You can dispense with time-consuming regrinding. The cutting edges can be changed much more easily, which is why they are widely used in industrial practice. Both the cutting inserts and the toolholders are standardized, the latter in DIN 4984.
Cutting inserts for toolholders
They are standardized in DIN ISO 1832 and are named with a code consisting of 10 characters:
- Insert shape: There are round, triangular, square, rhomboid and polygonal insert shapes, which are designated with letters. The corner angle is also determined with the shape .
- The (normal) clearance angle of the plate. It ranges from zero degrees to 30 degrees. So-called neutral plates with a clearance angle of zero are denoted by an N. With them, both the top and the bottom can be used as cutting edges, otherwise only the top.
- Tolerance of the plate: The diameter of the inscribed circle and the thickness of the plate are tolerated.
- Fastening and chip breaker : There are plates with a central hole for screwing or clamping and plates without a hole. The holes can be cylindrical or chamfered. Some have chip breakers on the top or on the underside.
- Cutting Edge Length: They range from 3.97 to 32mm. The diameter is given for round plates.
- Board thickness: They range from 1.59 mm to 9.52 mm.
- Corner radius : lies between 0 and 3.2 mm.
- Cutting edge design: There are sharp-edged cutting edges with a rounding (cutting edge radius), with bevels, chamfered and rounded, double beveled as well as double beveled and rounded cutting edges.
- Cutting or cutting direction: A distinction is made between right, left and neutral versions. The tools on the right cut from right to left. Neutral can be used in both directions.
- Cutting material (material):
- The simplest plates are made of hard metal . It is harder (and therefore more wear-resistant) and more brittle than high-speed steel, but softer and tougher than other cutting materials. It can be coated with harder cutting materials. Carbide can be used universally.
- Cermet (ceramic metal): Forms the transition to the cutting ceramics and is rarely used.
- Cutting ceramics : It is harder than carbide, especially at high temperatures, which is why it is suitable for high-speed machining and dry machining (without cooling lubricant ). However, it is also more brittle than hard metal and sensitive to fluctuating temperatures.
- Cubic boron nitride : After diamond, it is the hardest cutting material, but unlike diamond it does not lose its hardness at high temperatures and is also chemically resistant. Boron nitride is used for particularly hard materials ( hard cutting ) or for materials that contain particularly hard particles as inclusions, as these would otherwise lead to high wear.
- Diamond : is the hardest cutting material and is used for machining non-ferrous metals , including aluminum and copper alloys in particular. Diamond is also used for high-precision machining of these materials, such as mirrors. The achievable accuracies are Rz = 0.02 mm.
Types of attachment of the cutting plates
There are several ways to fix the cutting inserts in the clamp holders.
- Clamping system C: Here the panels are clamped from above with a clamping finger. The clamping finger itself contains a threaded hole and is pressed onto the non-drilling plate by means of a screw. An adjustable chip breaker can also be located between the clamping finger and the plate. This version is considered to be robust and easy to use.
- Clamping system M: From above via the clamping finger and at the same time via the bore. The plates contain a cylindrical bore. The clamping finger presses on the plate from above as well as on the side compartments of the hole inside the hole, thus preventing the plate from lifting off and slipping out at the same time.
- Clamping system P: only clamped over the hole. The plates contain a cylindrical bore. A clamping lever, which is clamped via a screw, presses on the inside of the bore. The plates can be changed particularly quickly.
- Clamping system S: Clamped over the hole with a clamping screw. The plates have a chamfered hole into which a screw is turned. This system is particularly simple and inexpensive and requires little space.
Standardization of the clamp holders
Similar to the cutting inserts, there is a system for naming the toolholders.
- Type of clamping
- Plate shape
- Holder shape: This determines the tool setting angle .
- Clearance angle of the plate
- Cutting direction: left, right or neutral.
- Shaft height
- Shaft width
- Tool length
- Cutting edge length
- Special shapes, higher accuracies or manufacturer-specific characters
Fastening of the clamp holder shafts in the machine
The shanks of the tools are either clamped directly in the tool slide (single tool) or clamped in a tool turret that can accommodate several tools. In addition to turning tools, driven tools can also be clamped there, for example milling or drilling tools. There are linear, star, polygon, drum, crown and disc turrets. Systems for square shafts are standardized in DIN 4984, systems for round shafts in DIN 8025. Prismatic shafts that are used in large machines are standardized in DIN 69880. The shaft systems are designed so that they maintain the stable position of the cutting edge - even under load.
Short clamp holder
Short clamp holders are clamp holders that have a screw at the rear for fastening in the machine. With them, the plate position can be adjusted lengthways and crossways using adjusting screws. They are preferred for internal machining. They are standardized in DIN 4985.
Cutting heads
Cutting heads are special, manufacturer-dependent (not standardized) tool holders that are designed for quick tool changes. Tool change times prevent production progress on the workpiece and thus mean reduced productivity. Cutting heads therefore introduce a further interface to the machine: An adapter is mounted in the tool holder in which the actual cutting heads can be quickly installed and removed. These systems are kept as short as possible so that they only take up little space. The exchange can be done manually or automatically. Cutting heads are suitable for a wide range of machining operations: longitudinal and face turning, external and internal turning, parting off and threading. Since the accuracy of the position of the tool cutting edge also depends on the deformation of the holder, cutting heads are designed for the greatest possible torsional rigidity and flexural rigidity .
Multi-task tools
Multi-task tools are turning tools that have multiple inserts at their end and are therefore similar to tool turrets. Multi-task tools, however, are clamped in drilling or milling spindles and are therefore intended for machining on machining centers (turning-milling machines) and turning cells . The spindle is rotated thereby such that the desired cutting edge for engagement occurs, and then remains during the machining in this angular position. As a result, the tool change times can be reduced on the one hand and the number of tools required on the other hand.
Thread making tools
For thread production on lathes, several processes can be used, each of which is carried out with a special tool. The processes are collectively referred to as screw turning . The thread turning is carried out with a pointed turning tool, the point angle of which corresponds to the flank angle of the thread. Thread turning chisels are made of high-speed steel or carbide and are offered either as full profile tools or as partial profile tools. In the case of the latter, the turned part is previously turned to the diameter that corresponds to the outer diameter of the thread (for external threads). This preparatory work is not necessary for tools with a full profile design, as they not only cut the flanks, but also the outer edges of the threads. When threading, the thread pitch corresponds to the feed rate (mm per revolution). Usually several overflows are necessary.
There are also thread chasers . They have several profiles next to each other so that only a single overflow is necessary. The thread pitch of thread chasers is therefore not variable.
With thread cutting dies and cutting brackets , which usually have three cutting edges (which, like chasers, cut several threads at the same time) on different sides of the circumference, threads can also be produced without the use of a lathe.
Tool selection
Usually, the turning process (longitudinal, face turning, etc.) is selected first on the basis of the blank and the shape to be produced. A decision is then made as to whether the workpiece should be roughed (rough machining) or finished (fine machining). This severely limits the number of tools that can be used. The shape of the cutting edges and the holder influences which shapes can be produced, the roughing / finishing affects the cutting forces that occur and thus the minimum stability of the cutting edge. The available machine power has a further influence. The choice of the rake angle and the chip breaker also depends on the material. Soft materials that tend to stick are more likely to be machined with a positive rake angle, materials with high strength with a negative one.
Web links
Individual evidence
- ↑ Pauksch: Zerspantechnik , 12th edition, page 109th
- ↑ Pauksch: Zerspantechnik , 12th edition, page 113th
- ↑ Pauksch: Zerspantechnik , 12th edition, page 109th
- ↑ Schönherr: Machining production . Oldenbourg, 2002, pp. 76-78.
- ↑ Michel Köcher: Tools and cutting materials for turning , pp. 166–168 in: Uwe Heisel, Fritz Klocke, Eckart Uhlmann, Günter Spur (eds.): Handbuch Spanen. 2nd edition, Hanser, Munich 2014.
- ↑ Michael Köcher: Tools for turning , pp. 169–171. in: Uwe Heisel, Fritz Klocke, Eckart Uhlmann, Günter Spur: Handbuch Spanen. 2nd edition, Hanser, Munich 2014.
- ↑ Schönherr: Machining production . Oldenbourg, 2002, p. 78 f.
- ↑ Michel Köcher: Tools and cutting materials for turning , p. 173 in: Uwe Heisel, Fritz Klocke, Eckart Uhlmann, Günter Spur (eds.): Handbuch Spanen. 2nd edition, Hanser, Munich 2014.
- ↑ Schönherr: Machining production . Oldenbourg, 2002, pp. 78-80.
- ↑ Michel Köcher: Tools and cutting materials for turning , p. 175 in: Uwe Heisel, Fritz Klocke, Eckart Uhlmann, Günter Spur (eds.): Handbuch Spanen. 2nd edition, Hanser, Munich 2014.
- ↑ Herbert Schönherr: Machining , Oldenbourg, 2002, p. 80.
- ↑ Michel Köcher: Tools and cutting materials for turning , p. 174 f. in: Uwe Heisel, Fritz Klocke, Eckart Uhlmann, Günter Spur (Eds.): Handbuch Spanen. 2nd edition, Hanser, Munich 2014.
- ↑ Michel Köcher: Tools and cutting materials for turning , p. 176 in: Uwe Heisel, Fritz Klocke, Eckart Uhlmann, Günter Spur (eds.): Handbuch Spanen. 2nd edition, Hanser, Munich 2014.
- ↑ Herbert Schönherr: Machining , Oldenbourg, 2002, p. 80 f.
- ↑ Michel Köcher: Tools and cutting materials for turning , p. 175 in: Uwe Heisel, Fritz Klocke, Eckart Uhlmann, Günter Spur (eds.): Handbuch Spanen. 2nd edition, Hanser, Munich 2014.
- ↑ Michel Köcher: Tools and cutting materials for turning , p. 164 f. in: Uwe Heisel, Fritz Klocke, Eckart Uhlmann, Günter Spur (Eds.): Handbuch Spanen. 2nd edition, Hanser, Munich 2014.