Open-pit mining: Difference between revisions

From Wikipedia, the free encyclopedia
Content deleted Content added
Replaced content with 'hi'
m Reverted edits by 80.193.174.7 (talk) to last version by LeaveSleaves
Line 1: Line 1:
{{Unreferenced|date=September 2008}}
hi
[[Image:Chino copper mine.jpg|thumb|right|350px|El Chino, located near [[Silver City, New Mexico]], is an open-pit copper mine]]

'''Open-pit mining''', also known as '''opencast mining''' and '''open-cut mining''' and '''strip mining''', refers to a method of extracting [[rock (geology)|rock]] or [[minerals]] from the earth by their removal from an open [[pit]] or [[Borrow pit|borrow]].

The term is used to differentiate this form of [[mining]] from extractive methods that require tunneling into the earth. Open-pit mines are used when deposits of commercially useful [[mineral]]s or [[Rock (geology)|rock]] are found near the surface; that is, where the ''overburden'' (surface material covering the valuable deposit) is relatively thin or the material of interest is structurally unsuitable for tunneling (as would be the case for sand, cinder, and gravel). For minerals that occur deep below the surface—where the overburden is thick or the mineral occurs as veins in hard rock— underground mining methods extract the valued material.

Open-pit mines that produce [[building material]]s are commonly referred to as '''[[quarry|quarries]]'''. People in some English-speaking countries are unlikely to make a distinction between an open-pit mine and other types of open-cast mines, such as quarries, [[Borrow pit|borrows]], [[Placer mining|placers]], and [[strip mining|strip mines]].

Open-pit mines are typically enlarged until either the [[mineral resource classification|mineral resource]] is exhausted, or an increasing ratio of overburden to ore makes further mining uneconomic. When this occurs, the exhausted mines are sometimes converted to [[landfill]]s for disposal of solid wastes. However, some form of water control is usually required to keep the mine pit from becoming a [[lake]].
[[Image:Quarry8093.JPG|thumb|right|350px|A [[coquina]] quarry]]

==Extraction==
Open Cut mines are dug on benches, which describe vertical levels of the hole. These benches are usually on four meter to sixty meter intervals, depending on the size of the machinery that is being used. Many quarries do not use benches, as they are usually shallow.

Most walls of the pit are generally dug on an angle less than vertical, to prevent and minimise damage and danger from rock falls. This depends on how weathered the rocks are, and the type of rock, and also how many structural weaknesses occur within the rocks, such as a [[Fault (geology)|fault]], [[Shear (geology)|shears]], joints or [[foliation (geology)|foliations]].

The walls are stepped. The inclined section of the wall is known as the batter, and the flat part of the step is known as the bench or berm. The steps in the walls help prevent rock falls continuing down the entire face of the wall. In some instances additional ground support is required and [[rock bolt]]s, cable bolts and shotcrete are used. De-watering bores may be used to relieve water pressure by drilling horizontally into the wall, which is often enough to cause failures in the wall by itself.

A haul road is situated at the side of the pit, forming a ramp up which [[trucks]] can drive, carrying [[ore]] and waste rock.

Waste rock is piled up at the surface, near the edge of the open cut. This is known as the waste dump. The waste dump is also tiered and stepped, to minimise [[degradation]].

Ore which has been processed is known as [[tailings]], and is generally a slurry. This is pumped to a tailings dam or settling pond, where the water evaporates. Tailings dams can often be [[toxic]] due to the presence of unextracted [[sulfide]] [[minerals]], some forms of toxic minerals in the gangue, and often [[cyanide]] which is used to treat [[gold]] ore via the cyanide leach process.

{{Panorama
|image = Image:Tagebau Garzweiler Panorama 2005.jpg
|fullwidth = 12000
|fullheight = 1464
|caption = Open-pit coal mining at [[Garzweiler open pit mine|Garzweiler]], [[Germany]]
|height = 230
}}

==Rehabilitation==
After mining finishes, the mine area must undergo [[Land rehabilitation|rehabilitation]]. Waste dumps are contoured to flatten them out, to further stabilise them. If the ore contains [[sulfides]] it is usually covered with a layer of [[clay]] to prevent access of [[rain]] and [[oxygen]] from the air, which can oxidise the sulfides to produce [[sulfuric acid]], a phenomenon known as [[acid mine drainage]]. This is then generally covered with [[soil]], and vegetation is planted to help consolidate the material. Eventually this layer will erode, but it is generally hoped that the rate of leaching or acid will be slowed by the cover such that the environment can handle the load of acid and associated heavy metals. There are no long term studies on the success of these covers due to the relatively short time in which large scale open pit mining has existed. It may take hundreds to thousands of years for some waste dumps to become "acid neutral" and stop leaching to the environment. The dumps are usually fenced off to prevent [[livestock]] denuding them of vegetation. The open pit is then surrounded with a [[fence]], to prevent access, and it generally eventually fills up with [[ground water]]. In arid areas it may not fill due to the deep groundwater levels.

==Typical open cut grades==
[[Gold]] is generally extracted in open cut mines at 1 to 2 ppm (grams per ton) but in certain cases, 0.75ppm gold is economic. This was achieved by bulk heap leaching at Alkane Minerals Ltd. Peak Hill mine in western [[New South Wales]], near [[Dubbo]], [[Australia]].

[[Nickel]], generally as laterite, is extracted via open cut down to 0.2%.
[[Copper]] is extracted at grades as low as 0.15% to 0.2%, generally in massive open cut mines in [[Chile]], where the size of the resources and favorable [[metallurgy]] allows economies of scale.

Materials typically extracted from open-pit mines include:
*[[Clay]]
*[[Coal]]
*[[Coquina]]
*[[Diamonds]]
*[[Gravel]] and [[Rock (geology)|stone]] (stone refers to bedrock, while gravel is unconsolidated material, as found in [[glacier|glacial]] or [[fluvial]] deposits)
*[[Granite]]
*[[Gritstone]]
*[[Gypsum]]
*[[Limestone]]
*[[Marble]]
*[[Metal]] [[ores]], such as [[copper]], [[iron]], [[gold]], and [[molybdenum]]
*[[Oil shale]]
*[[Sand]]
*[[Sandstone]]
*[[Slate]]

== Open-pit mines ==
[[Image:The Lavender Pit, Bisbee, AZ.jpg|thumb|right|The Lavender Pit, [[Bisbee, Arizona]]]]
This list includes only those large open-pit mines for which an article exists in Wikipedia.

===Australia===
* [[Super Pit gold mine|Super Pit]] – gold mine near [[Kalgoorlie, Western Australia]].
* [[Cadia mine]]; gold and copper mine located near [[Orange, New South Wales]].

===Canada===
* [[Adams Mine]] – controversial abandoned mine in [[Kirkland Lake, Ontario]].
* [[Colomac Mine]] – gold mine in [[Northwest Territories]], [[Canada]].
* [[Diavik Diamond Mine]] – [[diamond mine]] in [[Northwest Territories]], [[Canada]].
* [[Ekati Diamond Mine]] – diamond mine in [[Northwest Territories]], [[Canada]].
* [[Pine Point Mine]] – lead and zinc mine in [[Northwest Territories]], [[Canada]].
*[[Highland Valley Copper]]

===Chile===
* [[Chuquicamata]] – [[Chile]]an copper mine; the second largest open-pit copper mine in the world.
* [[Escondida]] copper mine
* [[Pascua Lama]] – gold and silver mine in [[Atacama]], [[Chile]] (in project)
* [[Radomiro Tomic (mine)|Radomiro Tomic]] copper mine
* [[El Abra]] copper mine
* [[Mantos Blancos]] copper mine
* [[Collahuasi]] copper mine
* [[El Indio]] Glod Mine
* [[Spence]] Copper Mine
* [[Proyecto Gaby]] Copper mine

===Colombia===
* [[Cerrejón]] – coal mine in [[Guajira Department]]. Largest coal open pit mine in the world.

===Indonesia===
* [[Grasberg mine]] – the largest gold mine and the third largest copper mine in the world located in the mountains of the [[Papua (Indonesian province)|Papua province]].

===Kyrgyzstan===
* [[Kumtor Gold Mine]] – gold mine in [[Tian Shan Mountains]] at 4,000-4,400 m (14,000 ft) above sea level.

===Mongolia===
* [[Boroo Gold Mine]] – gold mine 110 km (70 mi) WNW of the capital [[Ulan Bator]].

===Namibia===
* [[Rossing]] – uranium mine.
[[Image:Uncovered Coal Seams.jpg|thumb|Open Cast Mine, Uncovered Coal Seam, Kai Point Coal Mine, New Zealand]]
===New Zealand===
* Kai Point Coal Mine [http://www.kaipointcoal.co.nz] – coal mine, Kaitangata, South Otago, New Zealand

===Peru===
* [[Yanacocha]] – gold mine
* [[Tintaya]] copper mine
* [[Antamina]] Copper and Zinc mine
* [[Southern Peru]] Copper Mine
* [[Pierina]] Gold Mine
* [[ Lagunas Norte]] Gold Mine
* [[Cerro Verde]] Copper Mine
* [[Cerro Corona]] Gold Mine

===Portugal===
* [[Sao Domingos Mine]] – copper mine.

===Russia===
[[Image:Udachnaya pipe.JPG|thumb|right|The [[Udachnaya pipe]] in Russia.]]
* [[Mirny Mine]] − diamond mine in [[Mirny]], [[Siberia|Eastern Siberia]]
* [[Udachnaya pipe]] − diamond mine in [[Sakha|Yakutia]], [[Russia]].

===South Africa===
* The [[Big Hole]], a former diamond mine in [[Kimberley, South Africa|Kimberley]], [[South Africa]] more than 1,000 m (3,300 ft) deep; now a museum
* The [[Jagersfontein Mine]]

===United Kingdom===
* [[Penrhyn Quarry]] – [[slate industry|slate quarry]] in [[Wales]].

===United States===
* [[Berkeley Pit]] - former copper mine in [[Butte, Montana|Butte]], [[Montana]]; now a toxic lake and tourist attraction.
* [[El Chino Mine]] – copper mine in [[Grant County, New Mexico|Grant County]], [[New Mexico]].
* [[Hull-Rust-Mahoning Mine]] – largest open pit iron mine in the world near [[Hibbing, Minnesota]].
* [[Bingham Canyon Mine]] – largest excavation in the world; copper mine in [[Salt Lake County, Utah|Salt Lake County]], [[Utah]].
* [[Lavender Pit]] – copper mine in [[Cochise County, Arizona|Cochise County]], [[Arizona]].

==See also==
*[[List of minerals]]
*[[List of stone]]
*[[Ore|Definition of "ore"]]
*[[Ore genesis]]
*[[Mineral resource classification]]
*[[Bagger 288]], an enormous piece of pit-mining equipment

{{Mining techniques}}

[[Category:Surface mining]]

[[cs:Lom]]
[[de:Tagebau]]
[[et:Avakaevandamine]]
[[es:Mina a cielo abierto]]
[[nl:Dagbouw]]
[[ja:露天掘り]]
[[no:Dagbrudd]]
[[pl:Kopalnia odkrywkowa]]
[[pt:Mineração a céu aberto]]
[[fi:Avolouhos]]
[[sv:Dagbrott]]
[[uk:Кар'єр]]

Revision as of 12:39, 26 September 2008

El Chino, located near Silver City, New Mexico, is an open-pit copper mine

Open-pit mining, also known as opencast mining and open-cut mining and strip mining, refers to a method of extracting rock or minerals from the earth by their removal from an open pit or borrow.

The term is used to differentiate this form of mining from extractive methods that require tunneling into the earth. Open-pit mines are used when deposits of commercially useful minerals or rock are found near the surface; that is, where the overburden (surface material covering the valuable deposit) is relatively thin or the material of interest is structurally unsuitable for tunneling (as would be the case for sand, cinder, and gravel). For minerals that occur deep below the surface—where the overburden is thick or the mineral occurs as veins in hard rock— underground mining methods extract the valued material.

Open-pit mines that produce building materials are commonly referred to as quarries. People in some English-speaking countries are unlikely to make a distinction between an open-pit mine and other types of open-cast mines, such as quarries, borrows, placers, and strip mines.

Open-pit mines are typically enlarged until either the mineral resource is exhausted, or an increasing ratio of overburden to ore makes further mining uneconomic. When this occurs, the exhausted mines are sometimes converted to landfills for disposal of solid wastes. However, some form of water control is usually required to keep the mine pit from becoming a lake.

File:Quarry8093.JPG
A coquina quarry

Extraction

Open Cut mines are dug on benches, which describe vertical levels of the hole. These benches are usually on four meter to sixty meter intervals, depending on the size of the machinery that is being used. Many quarries do not use benches, as they are usually shallow.

Most walls of the pit are generally dug on an angle less than vertical, to prevent and minimise damage and danger from rock falls. This depends on how weathered the rocks are, and the type of rock, and also how many structural weaknesses occur within the rocks, such as a fault, shears, joints or foliations.

The walls are stepped. The inclined section of the wall is known as the batter, and the flat part of the step is known as the bench or berm. The steps in the walls help prevent rock falls continuing down the entire face of the wall. In some instances additional ground support is required and rock bolts, cable bolts and shotcrete are used. De-watering bores may be used to relieve water pressure by drilling horizontally into the wall, which is often enough to cause failures in the wall by itself.

A haul road is situated at the side of the pit, forming a ramp up which trucks can drive, carrying ore and waste rock.

Waste rock is piled up at the surface, near the edge of the open cut. This is known as the waste dump. The waste dump is also tiered and stepped, to minimise degradation.

Ore which has been processed is known as tailings, and is generally a slurry. This is pumped to a tailings dam or settling pond, where the water evaporates. Tailings dams can often be toxic due to the presence of unextracted sulfide minerals, some forms of toxic minerals in the gangue, and often cyanide which is used to treat gold ore via the cyanide leach process.

Open-pit coal mining at Garzweiler, Germany

Rehabilitation

After mining finishes, the mine area must undergo rehabilitation. Waste dumps are contoured to flatten them out, to further stabilise them. If the ore contains sulfides it is usually covered with a layer of clay to prevent access of rain and oxygen from the air, which can oxidise the sulfides to produce sulfuric acid, a phenomenon known as acid mine drainage. This is then generally covered with soil, and vegetation is planted to help consolidate the material. Eventually this layer will erode, but it is generally hoped that the rate of leaching or acid will be slowed by the cover such that the environment can handle the load of acid and associated heavy metals. There are no long term studies on the success of these covers due to the relatively short time in which large scale open pit mining has existed. It may take hundreds to thousands of years for some waste dumps to become "acid neutral" and stop leaching to the environment. The dumps are usually fenced off to prevent livestock denuding them of vegetation. The open pit is then surrounded with a fence, to prevent access, and it generally eventually fills up with ground water. In arid areas it may not fill due to the deep groundwater levels.

Typical open cut grades

Gold is generally extracted in open cut mines at 1 to 2 ppm (grams per ton) but in certain cases, 0.75ppm gold is economic. This was achieved by bulk heap leaching at Alkane Minerals Ltd. Peak Hill mine in western New South Wales, near Dubbo, Australia.

Nickel, generally as laterite, is extracted via open cut down to 0.2%. Copper is extracted at grades as low as 0.15% to 0.2%, generally in massive open cut mines in Chile, where the size of the resources and favorable metallurgy allows economies of scale.

Materials typically extracted from open-pit mines include:

Open-pit mines

The Lavender Pit, Bisbee, Arizona

This list includes only those large open-pit mines for which an article exists in Wikipedia.

Australia

Canada

Chile

Colombia

Indonesia

Kyrgyzstan

Mongolia

Namibia

Open Cast Mine, Uncovered Coal Seam, Kai Point Coal Mine, New Zealand

New Zealand

  • Kai Point Coal Mine [1] – coal mine, Kaitangata, South Otago, New Zealand

Peru

Portugal

Russia

The Udachnaya pipe in Russia.

South Africa

United Kingdom

United States

See also