Airspeed

from Wikipedia, the free encyclopedia
Airspeed indicator in a cockpit
Advertisement on the PFD of a modern airliner. The airspeed is displayed in knots on the left strip, with the Mach number below it.

The airspeed is the speed of an aircraft .

When measuring and specifying an airspeed (see airspeed indicator ), two important reference systems must be distinguished:

Speed ​​relative to the air (travel, airspeed)
The air flow on control surfaces and wings is created by the speed of an aircraft relative to the air . It therefore decides on the aerodynamic behavior of the aircraft (lift generation and maneuverability). It is measured on the outside of the aircraft and displayed on the airspeed indicator in the cockpit. The airspeed is the aerodynamically important speed. Your measurement is subject to some interfering influences, depending on the degree of correction, a distinction is made between several "types" of Airspeed.
Speed ​​relative to the ground (groundspeed)
The speed of an aircraft relative to the ground determines when individual waypoints of the flight route and ultimately the flight destination are reached. It differs from the Airspeed mainly in the influence of the wind. It can be calculated from the Airspeed or determined using a navigation system. The ground speed is the most important navigational speed. It can be considerably higher in a strong tailwind and considerably lower than the Airspeed in a strong headwind.

Speed ​​relative to the air (travel, airspeed)

Measurement method

Pitot tube on the underside of the wing of a small aircraft, the left end in the picture is flown against in flight

The speed is measured with the Pitot tube , actually called Prandtl probe or Prandtl's Pitot tube in the German-speaking area . It directly measures the pressure difference between the static pressure of the air that flows around the aircraft, and the total pressure of static pressure and dynamic pressure or dynamic pressure . The indicated airspeed (IAS) is derived from this pressure difference.

In principle, the measurement with the pitot tube is dependent on the (upwardly decreasing) air density to the same extent as the lift on the wings, so that the influence of the air density is automatically taken into account. The measurement method thus offers a good basis for assessing flight performance.

In the early days of aviation, attempts were made to use an impeller to measure the speed of slow aircraft .

The measurement through the pitot tube still contains a number of interfering influences. Therefore, several levels of correction are made. Some of these disruptive influences only become noticeable at high speeds or at great altitudes, and can therefore be neglected in hobby flying, but are important for commercial aviation.

The intermediate results of the respective correction levels each have their own designation:

Uncorrected airspeed (IAS)

The Uncorrected airspeed (also equipment speed or Indicated airspeed ;. Engl indicated airspeed , IAS ) is the speed of an aircraft relative to the surrounding air mass, which would result directly from the measured pressure difference.

The IAS is only relevant for small aircraft, as the CAS is displayed directly for larger aircraft.

The IAS is proportional to the square root of the quotient of dynamic pressure (total pressure minus static pressure) and air density . At high altitude, the IAS is smaller relative to air at the same speed. Since all air forces acting on the aircraft ( lift and drag ) are also dependent on the air density, the characteristic speeds ( stall speed V 0 , maneuver speed V A ) have constant IAS values, regardless of flight altitude and air pressure . The maximum permissible speed V NE, on the other hand, decreases with altitude, since it is mostly caused by the flutter , which increases with decreasing damping by the air.

Corrected Airspeed (CAS)

(Engl. When airspeed calibrated airspeed , CAS ) are the so-called static error corrected, but not the dynamic error .

The displacement of air through the aircraft fuselage creates a pressure wave, similar to the bow wave of a ship. This pressure wave leads to a falsification of the measurement result, which depends on the aircraft type and the installation location of the pitot tube. One speaks here of the instrument and installation error ( static source error ).

If the measuring scale has not been calibrated for the specific aircraft type, the displayed value is corrected using a table or a calculation formula specified in the technical manual for an aircraft type. In the case of small aircraft and their low speeds, the error usually remains so insignificant that it can be neglected.

Equivalent Airspeed (EAS)

The equivalent airspeed (engl. Equivalent airspeed , EAS ) is corrected in addition to the error due to the compressibility of the air.

Another Pitot tube measurement error increases significantly with increasing speed: the compression of the air.
Because the air in front of the pitot tube is compressed, the pitot tube sees a higher air density than it actually is. Since the error initially only increases slowly with the speed, the information on the speed at which the error must be taken into account varies considerably, in the range from 100 to over 250 knots.

This correction plays a rather minor role for take-off and landing, since the speeds are lower.

At medium to higher speeds, however, this speed is of essential importance, since the air forces on the aircraft depend on it (important for flight stability ). One could say: EAS is the speed that the aircraft “feels”.

However, if the speed approaches the speed of sound, the Mach number comes to the fore instead. (see section below)

The equivalent speed is a fictitious speed that provides information about the aerodynamic conditions. At the same equivalent speed , an aircraft always generates the same lift, regardless of the density of the surrounding air. At sea level in standard atmosphere corresponding equivalents speed of True speed . The thinner the air, the higher the true speed (TAS) has to be in order to achieve the same equivalent speed, i.e. the same aerodynamic effect. The equivalent speed not only allows statements about the lift, but also about other forces and variables, for example forces that act on the landing and control flaps, or how much frictional heat is generated and the like.

For small aircraft, the EAS still agrees to a sufficient approximation with CAS or even IAS due to the low speeds and altitudes and does not have to be determined separately.

True Airspeed (TAS)

The true airspeed (engl. True airspeed , TAS ) is the actual speed of the aircraft relative to the surrounding air. In the standard atmosphere at sea level and below 100 knots, TAS and IAS are almost the same. If the air density decreases (with increasing flight altitude or temperature) or the speed increases (increasing compression), the IAS is lower than the TAS .

The TAS is calculated from the EAS by including the air density in the calculation. It can be estimated from air pressure and temperature and tells you how much "attack mass" is available to a wing and how much mass flows against the sensors in the pitot system. The density of the air must not be confused with its pressure : warmer air has a lower density than colder air at the same pressure.

For commercial aircraft that cover a large area of ​​different air densities and speeds from the runway to the summit, this correction is very complex to calculate, since it must also be taken into account that the compression of the air also warms it up. The measured temperatures must be corrected accordingly.

In practice, the TAS is calculated from the CAS, so that two calculation steps are combined (CAS → EAS → TAS). The calculation is quite complex for high speeds. If the TAS is not calculated using a computer-aided display, it can be carried out in an iterative calculation using a flight calculator (slide rule similar to a slide rule, with additional auxiliary scales and tables).

For small aircraft and their area of ​​application, in turn, simplified formulas can be used or simplified display instruments can be used in which, for example, the TAS is determined by turning the scale ring and thereby bringing the so-called pressure altitude to coincide with the outside temperature (see figure of an airspeed indicator at the top). In contrast, such instruments would be completely unsuitable for high altitudes and high speeds.

For pilots of small aircraft following applies to a first approximation rule of thumb :

The IAS is about 2 percent per 1000 ft altitude lower than the TAS.

For example, at an altitude of 5000 ft with an IAS display of 100 kt, the true speed is 5 * 2% = 10% higher, i.e. 110 kt TAS.

formula

In principle, the following dependency applies:

With:

: Air density of the ICAO standard atmosphere
: Air density at the current altitude

However, this formula only helps to a limited extent in practice, since the air density cannot be measured directly, but has to be estimated from the air pressure and temperature.

Mach number

Disc rule specialized for aviation. (E.g. for converting Indicated Airspeed to True Airspeed or Indicated Airspeed to Mach number )

The Mach number is the ratio of the TAS to the speed of sound at the current air temperature.

At high speeds, the Mach number is often given instead of the TAS . The reason for this is that, particularly in the areas of the aircraft nose and on the upper side of the wings (especially on the leading edge of the wing and the transition from the wing to the fuselage), flow velocities occur that are well above the airspeed. Consequently, flow speeds in the supersonic range occur well below the speed of sound on the aircraft. Since the loads in the area of ​​the speed of sound increase almost by leaps and bounds, the maximum speed is not an absolute value, but a ratio to the speed of sound. Since the speed of sound decreases with falling temperatures, the maximum speed (TAS) also decreases with the temperature, so that the Mach number indicates how close one is approaching the maximum speed. The Mach number is also unsuitable for flight planning, but is used for aerodynamic control. In particular, for high-speed aircraft from about Mach 0.75, the maximum speed is not determined by the equivalent airspeed, but instead by the Mach number.

Speed ​​relative to the ground (groundspeed)

The ground speed (Engl. Groundspeed , GS ) refers to the order the wind influence (ie the movement of the air mass through which the air itself) corrected True airspeed . It represents the speed of an aircraft relative to the earth's surface. Knowledge of the ground speed is important for flight planning. Only it says when individual waypoints or the flight destination will be reached. Especially with a headwind or tailwind, the ground speed can differ considerably from the airspeed displayed in the cockpit; with a tailwind, the ground speed is the sum of the air speed and wind speed. Therefore, jet streams in the direction of flow are used to shorten the flight time.

Under special circumstances, a too low ground speed combined with a display in the cockpit that is too high can lead to accidents such as the Star Dust crashing over the Andes .

The ground speed can be calculated by taking the wind into account using a wind triangle based on the reports from the aviation weather station, but nowadays it is also measured using modern on-board systems (e.g. inertial navigation system , Doppler effect , air navigation radio service ).

Navigation methods such as GPS can also be used as a support . However, navigation using GPS alone is not permitted in civil aviation, as it is operated under military responsibility and control and is not operated by any recognized civil aviation organization. It is also prone to failure when there is increased solar activity . Because of its ease of use and availability, however, it plays an important complementary role in non-commercial aviation.

Unit of measurement

In aviation, all flight speeds are usually given in knots (1 knot = 1 kn = 1.852 km / h). Exceptions are Russia and the countries of the CIS . In contrast to the international standard, the airspeed in gliders and ultralight aircraft in Germany is measured in km / h.

In international civil aviation, a K (for knots) is often combined as a unit with the type of speed (IAS / TAS): KIAS ( knots indicated airspeed ) or KTAS ( knots true airspeed ).

For greater altitudes and speeds, the Mach number (the ratio to the speed of sound) is of additional use.

example

The different speeds are compared in the table below. Note how, despite a decreasing IAS, the ground speed ultimately increases with increasing altitude.

Altitude IAS TAS wind GS Do annotation
1000 ft
(approx. 300 m)
150 kt
(278 km / h)
153 kt
(283 km / h)
no wind 153 kt
(283 km / h)
average airliner shortly after takeoff
FL 100
(approx. 3 km)
250 kt
(463 km / h)
300 kt
(556 km / h)
300 kt
(556 km / h)
FL200
(approx. 6 km)
310 kt
(574 km / h)
434 kt
(803 km / h)
434 kt
(803 km / h)
FL360
(approx. 11 km)
280 kt
(518 km / h)
480 kt
(889 km / h)
20 kt tail
wind
500 kt
(926 km / h)
0.82 Cruise, higher IAS limited by Mach number
20 kt
headwind
460 kt
(852 km / h)

Typical speeds

For small powered aircraft , the typical cruising speed is around 110 kt (200 km / h). However, this can vary greatly depending on the type and engine. In commercial aircraft with turboprop engines, it is up to 350 kt (650 km / h). In jet-powered commercial aircraft , it is around 80% to 85% of the speed of sound, which - depending on the temperature between FL100 and FL360 - corresponds to around 490 to 540 kt (approx. 900 to 1000 km / h). The speed is limited by the aircraft structure, regulations, e.g. B. below FL100 (10,000  ft / 3,048 m flight altitude maximum 250 kt) and at the latest at cruising altitude through the Mach number (approaching the " sound barrier "). The speed of a glider is between 30 and 150 kn (≈ 50 - ≈ 270 km / h). The IAS / CAS / TAS of a balloon , on the other hand, is mostly almost zero, since it follows the air flow (apart from inertia effects).

Airspeed and engine power

The following approximation formula applies to the flight speed in level flight :

in which:

  • : Horizontal speed in m / s
  • : Engine power in hp
  • : Air screw efficiency
  • : Drag coefficient aircraft
  • : Acceleration due to gravity 9.81 m / s²
  • : Air density in kg / m³
  • : Wing area in m²

E.g. What is the cruising speed of a small-engine airplane with N = 100 HP; η L = 0.8; ρ = 1.2 kg / m³; C w = 0.06; A = 15 m² at low altitude?

literature

  • KJ Lush: Standardization of Take-Off Performance Measurements for Airplanes, Technical Note R-12. AFFTC, Edwards AFB, California.
  • John D. Anderson Jr .: Introduction to Flight, 3rd ed. McGraw-Hill Book, New York 1989.
  • Russel M. Herrington: Flight Test Engineering Handbook. AF Technical Report 6273, AFFTC, Edwards AFB, California 1966
  • Russell E. Erb: A Low Cost Method for Generating Takeoff Ground Roll Charts from Flight Test Data. Society of Flight Test Engineers (SFTE) 27th Annual Symposium, Fort Worth TX, 196
  • Private pilot manual. Jeppesen Sanderson, Englewood CO 1997, 2001, ISBN 0-88487-238-6
  • Peter Dogan: Instrument Flight Training Manual. Aviation Book, Santa Clarita CA 1991, 1999, ISBN 0-916413-12-8 .
  • Rod Machado: Instrument Pilot's Survival Manual. Aviation Speakers Bureau, Seal Beach CA 1991, 1998, ISBN 0-9631229-0-8 .
  • Wolfgang Kühr: The private pilot. Vol. 3, Technology II. Schiffmann Verlag, Bergisch Gladbach 1981, 1999, ISBN 3-921270-09-X .
  • Karl-Albin Kruse: The great book of aviation and space travel. Südwest-Verlag, Munich 1973, ISBN 3-517-00420-0 .
  • Klaus Hünecke: The technology of the modern airliner. Motorbuchverlag, Stuttgart 1998, ISBN 3-613-01895-0 .

Individual evidence

  1. DIN EN ISO 80000-3 : 2013 Sizes and units - Part 3: Space and time , Section 3-8.b