List of DIN standards / DIN EN

This list is a sub-list of the list of DIN standards .

DIN EN 1-999

DIN EN 1 heating stoves for liquid fuels with evaporation burners and chimney connection
DIN EN 2 fire classes
DIN EN 3 Portable fire extinguishers
DIN EN 14 dimensions of blankets
DIN EN 19 industrial valves - marking of metal valves
DIN EN 26 Gas-heated instant water heaters for sanitary use with atmospheric burners
DIN EN 31 Floor standing washbasins - connection dimensions
DIN EN 32 Wall-hung washbasins - connection dimensions
DIN EN 33 Floor standing toilet bowl with attached cistern - connection dimensions
DIN EN 34 toilet bowl, wall-hung with attached cistern - connection dimensions
DIN EN 35 Floor standing washbasin with top inlet - connection dimensions
DIN EN 36 Wall-hung seat washbasin with inlet from above - connection dimensions
DIN EN 37 Floor-standing toilet bowl with free inlet - connection dimensions
DIN EN 38 toilet bowl wall-hung with free inlet - connection dimensions
DIN EN 40 light masts
- Part 1 Definitions and terms
- Part 2 General requirements and dimensions
DIN EN 54 fire alarm systems
- Part 1 introduction
- Part 2 fire alarm control panels
- Part 3 fire alarm systems - acoustic signaling devices
- Part 4 energy supply facilities
- Part 5 heat detector; Point-shaped detectors
- Part 7 Smoke detector - Point-shaped detectors based on the scattered light, transmitted light or ionization principle
- Part 10 flame detector; Point-shaped detectors
- Part 11 manual call points
- Part 12 smoke detector - line-shaped detector based on the transmitted light principle
- Part 13 Evaluation of the compatibility of system components
- Part 16 Voice alarm centers
- Part 17 short circuit isolators
- Part 18 input / output devices
- Part 20 aspirating smoke detector
- Part 21 transmission devices for fire and fault messages
- Part 23 fire alarm devices - optical signaling devices
- Part 24 components for voice alarm systems - loudspeakers
- Part 25 Components that use radio frequency links
- Part 27 smoke detectors for monitoring ventilation ducts
DIN EN 58 Bitumen and bituminous binders - Sampling of bituminous binders
DIN EN 59 Glass fiber reinforced plastics; Determination of hardness with the Barcol hardness tester
DIN EN 71 safety of toys
- Part 1 Mechanical and physical properties
- Part 2 flammability
- Part 3 Migration of certain elements
- Part 4 experiment kits for chemical and similar experiments
- Part 5 chemical toys (sets) other than experiment kits
- Part 6 Graphic symbol for identification with an age group-related warning
- Part 7 finger paints; Requirements and test methods
- Part 8 swings, slides and similar activity toys for domestic use (indoor and outdoor)
- Part 9 Organic chemical compounds - Requirements
- Part 10 organic chemical compounds - sample preparation and extraction
- Part 11 Organic chemical compounds - Analytical methods
DIN EN 73 wood preservatives; Accelerated aging of treated wood prior to biological testing; Evaporation
DIN EN 74 couplings, centering bolts and base plates for work scaffolding and shoring
- Part 1 pipe couplings - requirements and test methods
- Part 2 special couplings - requirements and test methods
- Part 3 level base plates and centering bolts - Requirements and test methods
DIN EN 76 packaging for prepackages of certain foods; Volume of packaging made of glass and metal
DIN EN 80 wall-hung urinals - connection dimensions
DIN EN 81 safety rules for the construction and installation of elevators
DIN EN 84 Wood preservatives - Accelerated aging of treated wood before biological tests - Leaching stress
DIN EN 88 pressure regulators and associated safety devices for gas appliances
- Part 1 pressure regulator for inlet pressures up to and including 50 kPa
- Part 2 pressure regulator for inlet pressures above 500 mbar up to and including 5 bar
DIN EN 89 Gas-heated storage water heaters for sanitary use
DIN EN 107 test methods for windows; Mechanical tests
DIN EN 111 wall-hung hand wash basins - connection dimensions, October 2011 replaced by DIN EN 31
DIN EN 113 Wood preservatives - Test method for determining the preventive effectiveness against wood-destroying Basidiomycetes - Determination of the limit of effectiveness
DIN EN 115 Safety of escalators and moving walks
- Part 1: Construction and installation
- Part 2: Rules for increasing the safety of existing escalators and moving walks
DIN EN 116 Diesel fuels and household heating oils - Determination of the temperature limit value for filterability
DIN EN 117 Wood preservatives - Determination of the limit of effectiveness against Reticulitermes species (European termites) (laboratory method)
DIN EN 118 wood preservatives - Determination of the preventive effect against Reticulitermes species (European termites) (laboratory method)
DIN EN 120 wood-based materials; Determination of formaldehyde content; Extraction method called perforator method
DIN EN 124 attachments and covers for traffic areas - building principles, tests, marking, quality monitoring
DIN EN 125 Flame monitoring devices for gas appliances - Thermoelectric ignition safety devices
DIN EN 126 multiple control devices for gas devices
DIN EN 130 test method for doors; Testing the rigidity of door leaves by repeatedly twisting them
DIN EN 131 ladders
- Part 1 designations, types, functional dimensions
- Part 2 requirements, testing, labeling
- Part 3 user information
- Part 4 single or multi-articulated ladders
DIN EN 132 Respiratory protective devices - Definitions of terms and pictograms
DIN EN 133 Respiratory protective equipment - classification
DIN EN 134 Respiratory protective devices - Names of individual parts
DIN EN 135 Respiratory protective equipment - List of synonymous terms
DIN EN 136 Respiratory protective devices - Full face masks - Requirements, testing, labeling
DIN EN 137 Respiratory protective devices - Containers with compressed air (compressed air breathing apparatus) with full face masks - Requirements, testing, labeling
DIN EN 138 Respiratory protection devices - Fresh air hose devices in connection with full face masks, half masks or mouthpiece fittings - Requirements, testing, labeling
DIN EN 140 Respiratory protective devices - Half masks and quarter masks - Requirements, testing, marking
DIN EN 142 Respiratory protective devices - Mouthpiece sets - Requirements, testing, labeling
DIN EN 143 Respiratory protective devices - Particle filters - Requirements, testing, labeling
DIN EN 144 Respiratory protective devices - gas cylinder valves
- Part 1 threaded connection on the screw socket
- Part 2 threaded connection on the outlet port
- Part 3 threaded connections on the outlet nozzle for the diving gases nitrox and oxygen
DIN EN 145 Respiratory protective devices - Regeneration devices with pressurized oxygen or pressurized oxygen / nitrogen - Requirements, testing, labeling
DIN EN 148 Respiratory protective devices - threads for breathing connections
- Part 1 round thread connection
- Part 2 central thread connection
- Part 3 threaded connection M 45 × 3
DIN EN 149 Respiratory protective devices - Filtering half masks for protection against particles - Requirements, testing, labeling
DIN EN 152 Wood preservatives - Determination of the preventive effectiveness of a protective treatment of processed wood against blue stain - Laboratory method
DIN EN 153 Method for measuring the consumption of electrical energy and related properties for mains operated household refrigerators, freezers, freezers and their combinations
DIN EN 161 Automatic shut-off valves for gas burners and gas appliances
DIN EN 166 Personal eye protection
DIN EN 167 Personal eye protection - optical test methods
DIN EN 168 Personal eye protection - non-optical test methods
DIN EN 169 Personal eye protection - Filters for welding and allied techniques - Transmission requirements and recommended use
DIN EN 170 Personal eye protection - Ultraviolet protection filters - Transmission requirements and recommended use
DIN EN 171 Personal eye protection - Infrared protective filters - Transmission requirements and recommended use
DIN EN 172 Personal eye protection - sun protection filters for industrial use
DIN EN 174 Personal eye protection - ski goggles for alpine skiing
DIN EN 175 Personal protection - devices for eye and face protection during welding and allied processes
DIN EN 179 Locks and building hardware - Emergency exit locks with handle or push plate for doors in escape routes - Requirements and test methods
DIN EN 196 test method for cement
- Part 1 Determination of strength
- Part 2 Chemical analysis of cement
- Part 3 Determination of the solidification times and the spatial stability
- Part 5 Testing of the pozzolanity of pozzolan cement
- Part 6 Determination of the fineness of grinding
- Part 7 procedures for sampling and sample selection of cement
- Part 8 heat of hydration - solution method
- Part 9 Heat of hydration - Partial adiabatic process
- Part 10 Determination of the content of water-soluble chromium (VI) in cement
DIN EN 197 cement
- Part 1 Composition, requirements and conformity criteria of normal cement
- Part 2 conformity assessment
DIN EN 198 Sanitary equipment - Bathtubs made from cross-linked cast acrylic sheets - Requirements and test methods
DIN EN 200 sanitary fittings - drain valves and mixer taps (PN 10) - general technical specifications
DIN EN 201 Plastics and rubber machines - Injection molding machines - Safety requirements
DIN EN 204 Classification of thermoplastic wood adhesives for non-load-bearing applications
DIN EN 205 Adhesives - Wood adhesives for non-load-bearing applications - Determination of the adhesive strength of longitudinal bonds in a tensile test
DIN EN 206 concrete
- Part 1 definition, properties, manufacture and conformity, July 2014 replaced by DIN EN 206
- Part 9 Supplementary rules for self-compacting concrete (SCC), July 2014 replaced by DIN EN 206
DIN EN 207 Personal eye protection - Filters and eye protection devices against laser radiation (laser safety glasses)
DIN EN 208 Personal eye protection - Eye protection devices for adjustment work on lasers and laser assemblies (laser adjustment glasses)
DIN EN 212 Wood preservatives - General instructions for sampling and sample preparation of wood preservatives and treated wood for analysis
DIN EN 215 Thermostatic radiator valves - Requirements and testing
DIN EN 225 atomized oil burners - connection dimensions for oil burner pumps and oil burner motors
- Part 1 oil burner pumps
- Part 2 oil burner motors
DIN EN 226 oil atomization burner; Connection dimensions between burner and heat generator
DIN EN 228 Fuels for motor vehicles - Unleaded petrol - Requirements and test methods
DIN EN 230 automatic firing systems for oil burners, September 2012 replaced by DIN EN 298
DIN EN 232 bathtubs - connection dimensions
DIN EN 233 Wall coverings in rolls - Specifications for finished paper, vinyl and plastic wall coverings
DIN EN 234 Wall coverings in rolls - Specifications for wall coverings for subsequent treatment
DIN EN 235 wall coverings - terms and symbols
DIN EN 237 Liquid petroleum products - Petrol - Determination of low lead contents by atomic absorption spectrometry
DIN EN 238 Liquid petroleum products - Petrol - Determination of the benzene content by infrared spectrometry
DIN EN 241 Liquid petroleum products - Determination of sodium content - Atomic absorption spectrometry
DIN EN 246 sanitary fittings - General requirements for jet regulators
DIN EN 247 heat exchangers - terminology
DIN EN 248 sanitary fittings - General requirements for electrolytic Ni-Cr coatings
DIN EN 249 Sanitary equipment - Shower trays, made from cross-linked cast acrylic sheets - Requirements and test methods
DIN EN 250 breathing apparatus - Autonomous light diving apparatus with compressed air - Requirements, testing, marking
DIN EN 251 shower trays; Connection dimensions
DIN EN 252 wood preservatives; Outdoor test method to determine the relative protective effect of a wood preservative in contact with the ground
DIN EN 253 district heating pipes - Factory-insulated composite jacket pipe systems for directly underground district heating networks - composite pipe system, consisting of steel carrier pipe, polyurethane thermal insulation and outer jacket made of polyethylene
DIN EN 257 Mechanical temperature regulators for gas appliances
DIN EN 259 wall coverings in rolls - Heavy-duty wall coverings
- Part 1 requirements
- Part 2 Determination of impact resistance
DIN EN 263 Sanitary equipment - Crosslinked cast acrylic sheets for bathtubs and shower trays for domestic use
DIN EN 266 wall coverings in rolls; Specifications for textile wall coverings
DIN EN 267 Automatic blower burners for liquid fuels
DIN EN 269 Respiratory protection devices - Fresh air pressure hose devices with motor fan in connection with hood - Requirements, testing, marking
DIN EN 274 waste sets for sanitary equipment
- Part 1 requirements
- Part 2 test method
- Part 3 quality monitoring
DIN EN 275 wood preservatives; Determination of the protective effect against marine organisms
DIN EN 277 Sacks for the transport of food for food aid - Sacks made of polypropylene fabrics
DIN EN 280 Mobile aerial work platforms - Calculation - Stability - Construction - Safety - Tests
DIN EN 283 swap bodies; exam
DIN EN 284 swap bodies - non-stackable swap bodies of class C - dimensions and general requirements
DIN EN 285 Sterilization - Steam Sterilizers - Large Sterilizers
DIN EN 286 Simple unfired pressure vessels for air or nitrogen
- Part 1 pressure vessels for general purposes
- Part 2 pressure vessels for compressed air brake systems and auxiliary equipment in motor vehicles and their trailers
- Part 3 pressure vessel made of steel for compressed air brake systems and pneumatic auxiliary equipment in rail vehicles
- Part 4 pressure vessels made of aluminum alloys for compressed air brake systems and pneumatic auxiliary equipment in rail vehicles
DIN EN 287 Examination of welders - Fusion welding
- Part 1 steels
- Part 6 cast iron
DIN EN 289 Plastics and rubber machines - Presses - Safety requirements
DIN EN 293 oil pressure atomizer nozzles; Minimum requirements, tests
DIN EN 294 Safety distances against reaching danger points with the upper limbs, June 2008 replaced by DIN EN ISO 13857
DIN EN 295 stoneware pipe systems for sewers and sewers
- Part 1 requirements for pipes, fittings and connections
- Part 2 Evaluation of Conformity and Sampling
- Part 3 test method
- Part 4 requirements for transition and connection components and flexible couplings
- Part 5 requirements for perforated pipes and fittings
- Part 6 requirements for components for manholes and inspection shafts
- Part 7 Requirements for pipes and connections for pipe jacking
DIN EN 297 Boilers for gaseous fuels - Type B boilers with atmospheric burners, with a nominal heat load less than or equal to 70 kW
DIN EN 298 Automatic burner control units for burners and fuel devices for gaseous or liquid fuels
DIN EN 299 oil pressure atomizer nozzles
DIN EN 300 panels made of long, flat, aligned chips (OSB) - definitions, classification and requirements
DIN EN 301 Adhesives for load-bearing wooden components - Phenoplasts and aminoplasts - Classification and performance requirements
DIN EN 302 Adhesives for load-bearing wooden components - test methods
- Part 1 Determination of the longitudinal tensile shear strength
- Part 2 Determination of the delamination resistance
- Part 3 Determination of the influence of acid damage to wood fibers by temperature and humidity cycles on the transverse tensile strength
- Part 4 Determination of the influence of wood shrinkage on the shear strength
- Part 5 Determination of the maximum waiting time under reference conditions
- Part 6 Determination of the minimum pressing time under reference conditions
- Part 7 Determination of the service life under reference conditions
DIN EN 303 boiler
- Part 1 boiler with forced draft burner; Terms, general requirements, testing and labeling
- Part 2 boiler with forced draft burner; Special requirements for boilers with atomized oil burners
- Part 3 Central heating boilers for gaseous fuels - Assembly of boiler and forced draft burner
- Part 4 boiler with forced draft burner; Special requirements for boilers with forced draft oil burners with an output of up to 70 kW and a maximum operating pressure of 3 bar; Terms, special requirements, testing and labeling
- Part 5 boilers for solid fuels, manually and automatically fed firing systems, nominal heat output up to 500 kW - terms, requirements, tests and labeling
- Part 6 boiler with forced draft burner; Special requirements for the drinking water-side function of combination boilers with oil atomization burners with a nominal heat output less than or equal to 70 kW
- Part 7 central heating boiler for gaseous fuels with a forced draft burner with a nominal heat output less than or equal to 1 000 kW
DIN EN 304 Boilers - Test rules for boilers with atomized oil burners
DIN EN 305 heat exchangers - Terms and general specifications for the test to determine the performance
DIN EN 306 heat exchangers - measurements and measurement accuracy when determining the performance
DIN EN 307 heat exchangers - Instructions for the preparation of installation and operating instructions and maintenance instructions for maintaining the performance of heat exchangers of all types
DIN EN 308 heat exchangers - Test method for determining the performance criteria of air / air and air / flue gas heat recovery systems
DIN EN 309 chipboard - definition and classification
DIN EN 310 Wood-based panels - Determination of the flexural modulus of elasticity and flexural strength
DIN EN 311 Wood-based panels - Lifting resistance of the surface - Test method
DIN EN 312 chipboard - requirements
DIN EN 313 plywood - classification and terminology
- Part 1 classification
- Part 2 terminology
DIN EN 314 plywood - quality of the bond
- Part 1 test method
- Part 2 requirements
DIN EN 315 plywood - dimensional tolerances
DIN EN 316 wood fiber boards - definition, classification and symbols
DIN EN 317 chipboard and fiberboard; Determination of the swelling in thickness after immersion in water
DIN EN 318 Wood-based panels - Determination of dimensional changes in connection with changes in relative humidity
DIN EN 319 Chipboard and fibreboard - Determination of tensile strength perpendicular to the plane of the board
DIN EN 320 Chipboard and fibreboard - Determination of the axially parallel screw withdrawal resistance
DIN EN 321 wood-based materials; Determination of moisture resistance by cycle test
DIN EN 322 wood-based materials; Determination of the moisture content
DIN EN 323 wood-based materials; Determination of the bulk density
DIN EN 324 wood-based materials; Determination of the panel dimensions
- Part 1 Determination of the thickness, width and length
- Part 2 Determination of squareness and straightness of the edges
DIN EN 325 Wood-based materials - Determination of the dimensions of the test pieces
DIN EN 326 wood-based materials - sampling, cutting and monitoring
- Part 1 Sampling and cutting of the test pieces as well as specification of the test results
- Part 2 Initial type testing of the product and factory production control
- Part 3 Acceptance test of a single batch of panels
DIN EN 327 heat exchangers - fan-ventilated condensers - test methods for determining performance
DIN EN 328 heat exchangers - Test method for determining the performance criteria of fan air coolers
DIN EN 330 wood preservatives; Field test to determine the relative effectiveness of a wood preservative for use under a coat of paint and without contact with the ground: L-connection method
DIN EN 331 Manually operated ball valves and cone valves with closed bottoms for domestic gas installations
DIN EN 334 gas pressure regulators for inlet pressures up to 100 bar
DIN EN 335 Durability of wood and wood products - Use classes: Definitions, application to solid wood and wood products
DIN EN 336 timber for load-bearing purposes - dimensions, permissible deviations
DIN EN 338 Construction timber for load-bearing purposes - strength classes
DIN EN 340 protective clothing - general requirements
DIN EN 341 Personal fall protection equipment - descenders for rescue
DIN EN 342 Protective clothing - clothing systems and items of clothing for protection against cold
DIN EN 343 protective clothing - protection against rain
DIN EN 344 Safety, protective and occupational shoes for commercial use
- Part 1 Requirements and test methods, October 2004 replaced by DIN EN ISO 20344… DIN EN ISO 20347
- Part 2 Additional requirements and test methods, October 2004 replaced by DIN EN 15090, DIN EN ISO 20344 and DIN EN ISO 17249
DIN EN 345 safety shoes for commercial use
- Part 1 specification, October 2004 replaced by DIN EN ISO 20345
- Part 2 Additional specification, October 2004 replaced by DIN EN 15090, DIN EN ISO 20345 and DIN EN ISO 17249
DIN EN 346 protective shoes for commercial use
- Part 1 specification, October 2004 replaced by DIN EN ISO 20346
- Part 2 Additional specification, October 2004 replaced by DIN EN ISO 20346
DIN EN 347 occupational shoes for commercial use
- Part 1 specification, October 2004 replaced by DIN EN ISO 20345
- Part 2 Additional specification, October 2004 replaced by DIN EN ISO 20347
DIN EN 349 Safety of machines - Minimum distances to avoid crushing body parts
DIN EN 350 Durability of wood and wood products - Natural durability of solid wood
- Part 1 Principles for the testing and classification of the natural durability of wood
- Part 2 Guide for the natural durability and impregnability of selected types of wood of particular importance in Europe
DIN EN 351 Durability of wood and wood products - solid wood treated with wood preservatives
DIN EN 352 hearing protectors
DIN EN 353 Personal protective equipment against falls
- Part 1 fall arrest devices including fixed guide
- Part 2 traveling fall arrester including movable guide
DIN EN 354 Personal protective equipment against falls from a height - Lanyards
DIN EN 355 Personal protective equipment against falls from a height - energy absorbers
DIN EN 356 Glass in building - Special safety glazing - Test method and classification of the resistance to manual attack
DIN EN 357 Glass in building - Fire-resistant glazing made from transparent or translucent glass products - Classification of fire resistance
DIN EN 358 Personal protective equipment for restraint functions and for the prevention of falls - safety belts and lanyards for safety belts
DIN EN 360 Personal protective equipment against falls from a height - fall protection devices
DIN EN 361 Personal protective equipment against falls from a height - full body harnesses
DIN EN 362 Personal protective equipment against falls from a height - connecting elements
DIN EN 363 Personal protective equipment against falls from a height - Personal fall systems
DIN EN 364 Personal protective equipment against falls from a height - test method
DIN EN 365 Personal protective equipment against falls from a height - General requirements for instructions for use, maintenance, regular checks, maintenance, labeling and packaging
DIN EN 367 protective clothing; Protection against heat and flames; Test method: Determination of the heat transfer on exposure to flames
DIN EN 370 wood preservatives; Determination of anti-hatch control efficacy against Anobium punctatum (De Geer)
DIN EN 374 Protective gloves against chemicals and microorganisms
- Part 1 Terminology and Performance Requirements
- Part 2 Determination of the resistance to penetration
- Part 3 Determination of the resistance to permeation by chemicals
DIN EN 377 Lubricants for use in devices and associated control devices for fuel gases other than those intended for use in industrial processes
DIN EN 378 refrigeration systems and heat pumps - safety and environmental requirements
- Part 1 Basic requirements, terms, classifications and selection criteria
- Part 2 design, manufacture, testing, marking and documentation
- Part 3 Installation site and protection of people
- Part 4 operation, maintenance, repair and recovery
DIN EN 379 Personal eye protection - Automatic welding protection filters
DIN EN 380 timber structures; Test procedure; General principles for testing under static loads
DIN EN 381 protective clothing for users of hand-held chainsaws
- Part 1 test stand for testing the resistance to chainsaw cuts
- Part 2 test method for leg protection
- Part 3 test methods for footwear
- Part 4 test methods for protective gloves for chainsaws
- Part 5 requirements for leg protection
- Part 7 Requirements for protective gloves for chainsaws
- Part 8 test methods for protective gaiters for chainsaws
- Part 9 requirements for protective gaiters for chainsaws
- Part 10 test methods for upper body protection equipment
- Part 11 requirements for upper body protection equipment
DIN EN 382 fibreboard; Determination of surface absorption
- Part 1 test method for fibreboard according to the dry method
- Part 2 test method for hard plates
DIN EN 383 Timber structures - Test methods - Determination of embedment strength and bedding values for pin-shaped fasteners
DIN EN 384 Construction timber for load-bearing purposes - Determination of characteristic values for mechanical properties and bulk density
DIN EN 385 finger joints in construction timber - performance requirements and minimum requirements for production
DIN EN 386 Glulam - Performance requirements and minimum requirements for manufacture
DIN EN 387 Glulam - Universal finger joint connections - Performance requirements and minimum requirements for manufacture
DIN EN 388 protective gloves against mechanical risks
DIN EN 390 glulam - dimensions - limit dimensions
DIN EN 391 glued laminated timber - Delamination test of adhesive joints
DIN EN 392 glued laminated timber - shear test of the glue joints
DIN EN 397 industrial safety helmets
DIN EN 402 Respiratory protective devices - Automatic lung devices with compressed air (compressed air breathing apparatus) with full face mask or mouthpiece set for self-rescue - Requirements, testing, labeling
DIN EN 403 Respiratory protective devices for self-rescue - Filter devices with hood for self-rescue in the event of fire - Requirements, testing, labeling
DIN EN 404 Respiratory protective devices for self-rescue - filter self-rescuers with mouthpiece fittings for protection against carbon monoxide
DIN EN 405 Respiratory protective devices - Filtering half masks with valves for protection against gases or gases and particles - Requirements, testing, labeling
DIN EN 407 protective gloves against thermal risks (heat and / or fire)
DIN EN 408 Timber structures - Construction timber for load-bearing purposes and glued laminated timber - Determination of some physical and mechanical properties
DIN EN 409 timber structures - Test methods - Determination of the yield moment of pin-shaped fasteners
DIN EN 410 Glass in Building - Determination of the photometric and radiation-related parameters of glazing
DIN EN 413 plaster and wall ties
- Part 1 Composition, requirements and conformity criteria
- Part 2 test method
DIN EN 415 Safety of packaging machines
- Part 1 Terminology and classification of names for packaging machines and related equipment
- Part 2 packaging machines for prefabricated, dimensionally stable packaging
- Part 3 form, fill and seal machines
- Part 4 palletizers and depalletizers
- Part 5 wrapping machines
- Part 6 pallet wrapping machines
- Part 7 case packing machines
- Part 8 strapping machines
- Part 9 method for noise measurement in packaging machines, packaging lines and auxiliary equipment - accuracy classes 2 and 3
DIN EN 416 gas heater radiant heater - Dark heater with a burner with fan for commercial and industrial use
- Part 1 security
- Part 2 Rational Use of Energy
DIN EN 417 Metallic disposable cartridges for liquid gas with or without a withdrawal valve for the operation of portable devices - manufacture, inspection, testing and marking
DIN EN 418 Safety of machines, EMERGENCY STOP devices, functional aspects, design principles, March 2007 replaced by DIN EN ISO 13850
DIN EN 419 bright radiator with a burner without fan for commercial and industrial use
- Part 1 security
- Part 2 Rational Use of Energy
DIN EN 420 protective gloves - General requirements and test methods
DIN EN 421 protective gloves against ionizing radiation and radioactive contamination
DIN EN 422 Plastics and rubber machines - Blow molding machines - Safety requirements
DIN EN 424 Resilient floor coverings - Determination of the behavior in the event of an imitated movement of a furniture base
DIN EN 425 Resilient floor coverings and laminate floors - chair castor test
DIN EN 432 Resilient floor coverings - Determination of the shear force
DIN EN 437 test gases - test pressures - device categories
DIN EN 438 Decorative high-pressure laminate panels (HPL) - panels based on hardenable resins (laminates)
- Part 1 Introduction and general information
- Part 2 determination of properties
- Part 3 Classification and specifications for laminates with a thickness less than 2 mm, intended to be glued to a carrier material
- Part 4 Classification and specifications for compact laminates with a thickness of 2 mm and greater
- Part 5 Classification and specifications for laminates for floors with a thickness of less than 2 mm, intended to be glued to a substrate
- Part 6 Classification and specifications for compact laminates for outdoor use with a thickness of 2 mm and greater
- Part 7 Compact panels and HPL multilayer composite panels for wall and ceiling cladding for indoor and outdoor use
- Part 8 Classification and Specifications for Design Laminates
- Part 9 Classification and specifications for laminates with an alternative core structure
DIN EN 442 radiators and convectors
- Part 1 Technical Specifications and Requirements
- Part 2 test procedure and performance specification
- Part 3 conformity assessment
DIN EN 443 fire helmets for fire fighting in buildings and other structures
DIN EN 444 Non-destructive testing; Basics for radiographic testing of metallic materials with X-rays and gamma rays
DIN EN 445 grout for tendons - test method
DIN EN 446 grout for tendons - grouting method
DIN EN 447 grout for tendons - General requirements
DIN EN 448 district heating pipes - Factory-insulated composite jacket pipe systems for directly buried district heating networks - Composite fittings, consisting of steel medium pipe, polyurethane thermal insulation and outer jacket made of polyethylene
DIN EN 449 Specifications for liquefied gas appliances - Flueless domestic space heaters (including heaters with diffusive catalytic combustion)
DIN EN 450 fly ash for concrete
- Part 1 definition, requirements and conformity criteria
- Part 2 conformity assessment
DIN EN 451 test method for fly ash
- Part 1 Determination of the free calcium oxide content
- Part 2 Determination of the fineness by wet sieving
DIN EN 452 swap bodies - class A swap bodies - dimensions and general requirements
DIN EN 453 Food processing machines - Dough kneading machines - Safety and hygiene requirements
DIN EN 454 Food processing machines - Planetary mixers and kneaders - Safety and hygiene requirements
DIN EN 455 Medical gloves for single use
- Part 1 requirements and testing for leaks
- Part 2 Requirements and testing of physical properties
- Part 3 Requirements and testing for biological evaluation
- Part 4 Requirements and testing to determine the minimum shelf life
DIN EN 457 Safety of machines; Acoustic hazard signals, December 2005 replaced by DIN EN ISO 7731
DIN EN 458 hearing protectors - recommendations for selection, use, care and maintenance
DIN EN 459 building lime
- Part 1 Terms, requirements and conformity criteria
- Part 2 test method
- Part 3 conformity assessment
DIN EN 460 Durability of wood and wood products - Natural durability of solid wood - Guide to the requirements for the durability of wood for use in the hazard classes
DIN EN 461 Specifications for liquefied gas appliances - Flueless commercial space heaters up to 10 kW
DIN EN 462 Non-destructive testing; Image quality of radiographs
- Part 1 image quality test body (wire bar); Determination of the image quality figure
- Part 2 image quality test body (step / hole type); Determination of the image quality figure
- Part 3 image quality classes for ferrous materials
- Part 4 Experimental determination of image quality figures and image quality tables
- Part 5 image quality test body (double wire bridge), determination of the image blurring
DIN EN 464 Protective clothing - Protection against liquid and gaseous chemicals including liquid aerosols and solid particles - Test method: Determination of the leak tightness of gas-tight suits (internal pressure test method)
DIN EN 469 Protective clothing for fire fighters - Performance requirements for protective clothing for fire fighting
DIN EN 470 protective clothing for welding and allied processes
- Part 1 General requirements, January 2008 replaced by DIN EN ISO 11611
DIN EN 471 warning clothing - test methods and requirements
DIN EN 472 pressure measuring devices - terms
DIN EN 474 earth-moving machines - safety
- Part 1 General Requirements
- Part 2 requirements for grading machines
- Part 3 requirements for loaders
- Part 4 requirements for backhoe loaders
- Part 5 requirements for hydraulic excavators
- Part 6 requirements for dump trucks
- Part 7 requirements for scrapers
- Part 8 Requirements for Graders
- Part 9 requirements for pipelayers
- Part 10 requirements for trenching
- Part 11 requirements for earth and garbage compactors
- Part 12 requirements for dragline excavators
DIN EN 476 General requirements for components for sewers and sewers
DIN EN 477 Profiles made of plasticizer-free polyvinyl chloride (PVC-U) for the production of windows and doors - Determination of the impact resistance of main profiles using drop bolts
DIN EN 478 Profiles made of plasticizer-free polyvinyl chloride (PVC-U) for the production of windows and doors - Determination of behavior after storage at 150 ° C - Test method
DIN EN 479 Profiles made of plasticizer-free polyvinyl chloride (PVC-U) for the production of windows and doors - Determination of heat shrinkage
DIN EN 480 admixtures for concrete, mortar and grout - test method
- Part 1 reference concrete and reference mortar for tests
- Part 2 Determination of the solidification time
- Part 4 Determination of the water secretion of the concrete (bleeding)
- Part 5 Determination of capillary water absorption
- Part 6 infrared investigation
- Part 8 Determination of the solid content
- Part 10 Determination of the water-soluble chloride content
- Part 11 Determination of air void parameters in hardened concrete
- Part 12 Determination of the alkali content of additives
- Part 13 Reference construction mortar for testing admixtures for masonry mortar
- Part 14 Determination of the corrosion behavior of steel in concrete - Electrochemical test with constant potential
- Part 15 reference concrete and test methods for testing viscosity-modifying admixtures
DIN EN 481 workplace atmosphere; Definition of the particle size distribution for measuring airborne particles
DIN EN 482 Exposure at the workplace - General requirements for the performance of methods for measuring chemical agents
DIN EN 483 Boilers for gaseous fuels - Type C boilers with a nominal heat load equal to or less than 70 kW
DIN EN 484 Specifications for LPG appliances - LPG-powered cooking appliances including those with grill parts for outdoor use
DIN EN 485 aluminum and aluminum alloys - strips, sheets and plates
- Part 1 Technical delivery conditions
- Part 2 mechanical properties
- Part 3 dimensional limits and shape tolerances for hot-rolled products
- Part 4 dimensions and shape tolerances for cold-rolled products
DIN EN 486 aluminum and aluminum alloys - billets - specifications
DIN EN 487 Aluminum and aluminum alloys - Rolling bars - Specifications
DIN EN 488 district heating pipes - Factory-insulated composite jacket pipe systems for directly underground district heating networks - Pre-insulated shut-off valves for steel medium pipes with polyurethane thermal insulation and outer jacket made of polyethylene
DIN EN 489 district heating pipes - Factory insulated composite jacket pipe systems for direct underground district heating networks - Pipe connections for steel medium pipes with polyurethane thermal insulation and outer jacket made of polyethylene
DIN EN 490 Roof and shaped stones made of concrete for roofs and wall cladding - Product requirements
DIN EN 491 Concrete roof and shaped bricks for roofs and wall cladding - Test method
DIN EN 492 fiber cement roof panels and associated molded parts - product specification and test methods
DIN EN 494 fiber cement corrugated sheets and associated molded parts - product specification and test methods
DIN EN 495 waterproofing membranes - Determination of the behavior when folding at low temperatures
- Part 5 plastic and elastomer sheets for roof waterproofing
DIN EN 497 Specifications for LPG appliances - LPG-powered multi-purpose cooking appliances for outdoor use
DIN EN 498 Specifications for liquefied gas appliances - grills for outdoor use including contact grills
DIN EN 500 Mobile road construction machines - Safety
- Part 1 Common Requirements
- Part 2 Special requirements for road milling machines
- Part 3 Special requirements for soil stabilization machines and recycling machines
- Part 4 Special requirements for compaction machines
- Part 6 Special requirements for road pavers
DIN EN 501 roofing products made of sheet metal - Specification for fully supported roofing elements made of zinc sheet
DIN EN 502 Roofing products made of sheet metal - Specification for fully supported roofing products made of stainless steel sheet
DIN EN 504 Roofing products made of sheet metal - Specification for fully supported roofing elements made of copper sheet
DIN EN 505 Roofing products made of sheet metal - Specification for fully supported roofing products made of sheet steel
DIN EN 506 Roofing products made of sheet metal - Specifications for self-supporting roofing elements made of copper or zinc sheet
DIN EN 507 Roofing products made of sheet metal - Specification for fully supported roofing elements made of aluminum sheet
DIN EN 508 Roofing products made of sheet metal - Specifications for self-supporting roofing elements made of sheet steel, aluminum sheet or stainless steel sheet
- Part 1 steel
- Part 2 aluminum
- Part 3 Stainless steel
DIN EN 509 Decorative gas appliances with fuel effect
DIN EN 510 Specifications for protective clothing for areas in which there is a risk of entanglement in moving parts
DIN EN 511 protective gloves against cold
DIN EN 512 fiber cement products - pressure pipes and connections
DIN EN 513 Profiles made of plasticizer-free polyvinyl chloride (PVC-U) for the production of windows and doors - Determination of weather fastness and weather resistance through artificial weathering
DIN EN 514 Profiles made of plasticizer-free polyvinyl chloride (PVC-U) for the production of windows and doors - Determination of the strength of welded corners and T-joints
DIN EN 515 aluminum and aluminum alloys; Workpiece; Designations of the material conditions
DIN EN 516 Prefabricated accessories for roof coverings - Facilities for stepping on the roof - Catwalks, treads and single steps
DIN EN 517 Prefabricated accessories for roof coverings - safety roof hooks
DIN EN 520 plasterboard - terms, requirements and test methods
DIN EN 521 Specifications for LPG devices - Portable LPG devices operated with vapor pressure
DIN EN 523 steel strip ducts for tendons - terms, requirements and conformity
DIN EN 524 steel strip ducts for tendons - test method
- Part 1 Determination of the shapes and dimensions
- Part 2 Determination of the bending behavior
- Part 3 back and forth bending test
- Part 4 Determination of the transverse load capacity
- Part 5 Determination of tensile strength
- Part 6 Determination of tightness (determination of water loss)
DIN EN 525 Gas-fired warm air heaters without a heat exchanger with forced convection for heating rooms for non-domestic use with a nominal heat load not exceeding 300 kW
DIN EN 526 Inland navigation vehicles; Jetties up to 8 m in length; Requirements, types
DIN EN 527 office furniture - office work tables
- Part 1 dimensions
- Part 2 requirements for safety, strength and durability
DIN EN 528 storage and retrieval machines - safety requirements
DIN EN 529 Respiratory protective devices - Recommendations for selection, use, care and maintenance - Guidelines
DIN EN 530 Abrasion resistance of material for protective clothing - test method
DIN EN 534 Corrugated bitumen sheets - Product specifications and test methods
DIN EN 536 Road construction machines - Asphalt mixing plants - Safety requirements
DIN EN 538 clay roof tiles for overlapping laying - testing of the bending capacity
DIN EN 539 Roof tiles for overlapping installation - Determination of the physical properties
- Part 1 testing of water impermeability
- Part 2 Testing of frost resistance
DIN EN 541 Aluminum and aluminum alloys - Rolled products for cans, closures and lids - Specifications
DIN EN 542 Adhesives - Determination of density
DIN EN 543 Adhesives - Determination of the bulk density of powder and granulate adhesives
DIN EN 544 bitumen shingles with mineral-based insert and / or plastic insert - product specification and test method
DIN EN 545 Pipes, fittings, accessories made of ductile cast iron and their connections for water pipes - requirements and test methods
DIN EN 546 aluminum and aluminum alloys - foils
- Part 1 Technical delivery conditions
- Part 2 mechanical properties
- Part 3 tolerances
- Part 4 Special property requirements
DIN EN 547 Safety of machines - human body measurements
- Part 1 Basics for determining dimensions for whole-body access to machine workplaces
- Part 2 Basics for the dimensioning of access openings
- Part 3 body measurement data
DIN EN 549 Elastomer materials for seals and membranes in gas appliances and gas systems
DIN EN 556 Sterilization of medical devices - Requirements for medical devices that are marked as "STERILE"
- Part 1 Requirements for medical devices that have been sterilized in their final packaging
- Part 2 Requirements for aseptically manufactured medical devices
DIN EN 558 Industrial valves - Face-to-face lengths of metal valves for installation in pipelines with flanges - Valves labeled according to PN and Class
- Part 1 Technical delivery conditions
- Part 2 mechanical properties
- Part 3 tolerances
- Part 4 Special property requirements
DIN EN 560 gas welding devices - Hose connections for devices and systems for welding, cutting and allied processes
DIN EN 561 gas welding devices - hose couplings with automatic gas lock for welding, cutting and related processes
DIN EN 564 Mountaineering equipment - Accessory cord - Safety requirements and test methods
DIN EN 565 mountaineering equipment - tape - safety requirements and test methods
DIN EN 566 Mountaineering equipment - Slings - Safety requirements and test methods
DIN EN 567 Mountaineering equipment - Rope clamps - Safety requirements and test methods
DIN EN 568 Mountaineering equipment - Anchoring means in ice - Safety requirements and test methods
DIN EN 569 Mountaineering equipment - Rock hooks - Safety requirements and test methods
DIN EN 570 aluminum and aluminum alloys - slugs for extrusion made from semi-finished products - specification
DIN EN 571 Non-destructive testing - liquid penetrant testing
- Part 1 General Basics
DIN EN 573 Aluminum and aluminum alloys - Chemical composition and form of semi-finished products
- Part 1 Numerical designation system
- Part 2 Designation system with chemical symbols
- Part 3 Chemical composition and product forms
DIN EN 574 Safety of machines - Two-hand controls - Functional aspects - Principles for design
DIN EN 575 Aluminum and aluminum alloys - Master alloys, produced by melting - Specifications
DIN EN 576 Aluminum and aluminum alloys - Unalloyed aluminum in pigs - Specifications
DIN EN 577 Aluminum and aluminum alloys - Liquid metal - Specifications
DIN EN 580 Plastics piping systems - Pipes made of plasticizer-free polyvinyl chloride (PVC-U) - Test method for resistance to dichloromethane at a specified temperature (DCMT)
DIN EN 581 outdoor furniture - seating and tables for camping, living and contracting
- Part 1 General safety requirements
- Part 2 Mechanical safety requirements and test methods for seating furniture
- Part 3 Mechanical safety requirements and test methods for tables
DIN EN 582 thermal spraying; Determination of the adhesive tensile strength
DIN EN 583 Non-destructive testing - Ultrasonic testing
- Part 1 General principles
- Part 2 sensitivity and distance adjustment
- Part 3 transmission technology
- Part 4 Testing for inhomogeneity perpendicular to the surface
- Part 5 Description and size determination of inhomogeneities
- Part 6 time-of-flight diffraction technique, a technique for finding and measuring inhomogeneities
DIN EN 586 aluminum and aluminum alloys - forgings
- Part 1 Technical delivery conditions
- Part 2 Mechanical properties and additional property requirements
- Part 3 dimensional limits and shape tolerances
DIN EN 588 fiber cement pipes for sewers and sewers
- Part 1 pipes, pipe connections and fittings for gravity lines
- Part 2 manholes and inspection shafts
DIN EN 589 Fuels for motor vehicles - Liquid gas - Requirements and test methods
DIN EN 590 Fuels for motor vehicles - Diesel fuel - Requirements and test methods
DIN EN 593 industrial valves - metallic valves
DIN EN 594 Timber structures - Test methods - Wall panel load-bearing capacity and rigidity of wall elements in wood panel construction
DIN EN 595 timber structures - Test methods - Testing of lattice girders to determine the load-bearing capacity and deformation behavior
DIN EN 596 Timber structures - Test methods - Testing of walls in wood panel construction with soft impact
DIN EN 597 Furniture - Assessment of the flammability of mattresses and upholstered bed bases
- Part 1 ignition source: smoldering cigarette
- Part 2 Ignition source: A gas flame comparable to a burning match
DIN EN 598 Pipes, fittings, accessories made of ductile cast iron and their connections for waste water disposal - requirements and test methods
DIN EN 599 Durability of wood and wood products - effectiveness of wood preservatives as determined by biological tests
- Part 1 specification according to the usage class
- Part 2 classification and labeling
DIN EN 601 Aluminum and aluminum alloys - Castings - Chemical composition of castings that come into contact with food
DIN EN 602 Aluminum and aluminum alloys - Wrought products - Chemical composition of semi-finished products for the manufacture of products that come into contact with food
DIN EN 603 Aluminum and aluminum alloys - Extruded or rolled forged raw material
- Part 1 Technical delivery conditions
- Part 2 mechanical properties
- Part 3 dimensional limits and shape tolerances
DIN EN 604 Aluminum and aluminum alloys - Cast forging raw material
- Part 1 Technical delivery conditions
- Part 2 dimensional limits and form tolerances
DIN EN 606 bar coding - labels for transport and handling of steel products
DIN EN 607 hanging gutters and accessories made of PVC-U - terms, requirements and testing
DIN EN 609 Agricultural and forestry machinery - Safety of log splitting machines
- Part 1 wedge splitting machines
- Part 2 screw splitting machines
DIN EN 610 tin and tin alloys - tin in pigs
DIN EN 611 tin and tin alloys - tin alloys and tin equipment
- Part 1 tin alloys
- Part 2 tin device
DIN EN 613 convection space heater for gaseous fuels
DIN EN 614 Safety of machines - Ergonomic design principles
- Part 1 Terms and general principles
- Part 2 Interactions between the design of machines and the work tasks
DIN EN 615 Fire protection - Extinguishing media - Requirements for extinguishing powder (not for extinguishing powder of fire class D)
DIN EN 617 Continuous conveyors and systems - Safety and EMC requirements for equipment for the storage of bulk goods in silos, bunkers, storage containers and hoppers
DIN EN 618 Continuous conveyors and systems - Safety and EMC requirements for mechanical conveying devices for bulk goods with the exception of stationary belt conveyors
DIN EN 619 Continuous conveyors and systems - Safety and EMC requirements for mechanical conveyor systems for piece goods
DIN EN 620 Continuous conveyors and systems - Safety and EMC requirements for stationary belt conveyors for bulk goods
DIN EN 621 Gas-fired warm air heaters with forced convection for heating rooms for non-domestic use with a nominal heat load not exceeding 300 kW, without a fan to convey the combustion air and / or the exhaust gases
DIN EN 622 fibreboard - requirements
- Part 1 General Requirements
- Part 2 requirements for hard plates
- Part 3 requirements for medium-hard plates
- Part 4 requirements for porous plates
- Part 5 requirements for boards according to the dry process (MDF)
DIN EN 623 high-performance ceramics - monolithic ceramics; General and structural properties
- Part 1 Testing for the presence of surface defects by dye penetration tests
- Part 2 Determination of density and porosity
- Part 3 Determination of the grain size and the grain size distribution (line intercept method)
- Part 4 Determination of the surface roughness
- Part 5 Determination of the volume fraction of phases by evaluating microstructure recordings
DIN EN 624 Specifications for liquefied gas operated devices - Room air independent liquefied gas space heaters for installation in vehicles and boats
DIN EN 625 boilers for gaseous fuels - Special requirements for the drinking water-side function of combination boilers with a nominal heat load of less than or equal to 70 kW
DIN EN 626 Safety of machines - Reduction of the health risk from hazardous substances emanating from machines
- Part 1 principles and specifications for machine manufacturers
- Part 2 Methodology for Establishing Review Procedures
DIN EN 627 rules for data acquisition and remote monitoring of elevators, escalators and moving walks
DIN EN 629 Transportable gas cylinders - 25E tapered thread for connecting valves to gas cylinders
- Part 1 specification, December 2010 replaced by DIN EN ISO 11363-1
DIN EN 631 Materials and objects in contact with food; Food containers
- Part 1 dimensions of the container
- Part 2 Dimensions of the accessories and the supports
DIN EN 633 cement-bonded chipboard; Definition and classification
DIN EN 634 cement-bonded chipboard - requirements
- Part 1 General Requirements
- Part 2 Requirements for Portland cement (PZ) bonded chipboard for use in dry, damp and outdoor areas
DIN EN 635 plywood - classification according to the appearance of the surface
- Part 1 General
- Part 2 hardwood
- Part 3 softwood
- Part 5 measurement methods and indication of features and errors
DIN EN 636 plywood - requirements
DIN EN 637 Plastics piping systems - Parts made of glass fiber reinforced plastics - Determination of the content of components using the gravimetric method
DIN EN 639 General requirements for pressure pipes made of concrete, including pipe connections and fittings
DIN EN 640 Reinforced concrete pressure pipes and concrete pressure pipes with distributed reinforcement (without sheet metal jacket), including pipe connections and fittings
DIN EN 641 reinforced concrete pressure pipes with sheet metal jacket, including pipe connections and fittings
DIN EN 642 Prestressed concrete pressure pipes, with and without sheet metal jacket, including pipe connections, fittings and special requirements for prestressing steel for pipes
DIN EN 643 paper and cardboard - European list of standard grades for waste paper and cardboard
DIN EN 645 Paper and cardboard intended for contact with food; Production of a cold water extract
DIN EN 646 Paper and cardboard intended for contact with food - Determination of the color fastness of colored paper and cardboard
DIN EN 647 Paper and cardboard intended for contact with food; Preparation of a hot water extract
DIN EN 648 Paper and cardboard intended for contact with food - Determination of the color fastness of optically brightened paper and cardboard
DIN EN 649 Resilient floor coverings - Homogeneous and heterogeneous polyvinyl chloride floor coverings - Specification
DIN EN 650 Resilient floor coverings - Floor coverings made of polyvinyl chloride with a back made of jute or polyester fleece or on polyester fleece with a back made of polyvinyl chloride - Specification
DIN EN 651 Resilient floor coverings - Polyvinyl chloride floor coverings with a foam layer - Specification
DIN EN 652 Resilient floor coverings - Polyvinyl chloride floor coverings with a cork-based backing - Specification
DIN EN 655 Resilient floor coverings - Panels on a back made of pressed cork with a polyvinyl chloride wear layer - Specification
DIN EN 656 Boilers for gaseous fuels - Type B boilers with a nominal heat load greater than 70 kW but equal to or less than 300 kW
DIN EN 657 Thermal spraying - terms, classification
DIN EN 658 Mountaineering equipment - Anchoring means in ice - Safety requirements and test methods
DIN EN 659 fire brigade protective gloves
DIN EN 660 Resilient floor coverings - Determination of wear behavior
- Part 1 Stuttgart exam
- Part 2 Frick-Taber exam
DIN EN 661 Resilient floor coverings - Determination of the spread of water
DIN EN 662 Resilient floor coverings - Determination of the curvature when exposed to moisture
DIN EN 663 Resilient floor coverings - Determination of the decor depth
DIN EN 664 Resilient floor coverings - Determination of the loss of volatile components
DIN EN 665 Resilient floor coverings - Determination of plasticizer release
DIN EN 666 Resilient floor coverings - Determination of gelation
DIN EN 669 Resilient floor coverings - Determination of the change in dimensions of linoleum panels due to changes in air humidity
DIN EN 671 Fixed extinguishing systems - wall hydrants
- Part 1 hose reels with dimensionally stable hose
- Part 2 wall hydrants with flat hose
- Part 3 Maintenance of hose reels with dimensionally stable hose and wall hydrants with flat hose
DIN EN 672 Resilient floor coverings - Determination of the bulk density of pressed cork
DIN EN 673 Glass in building - Determination of the heat transfer coefficient (U-value) - Calculation method
DIN EN 674 Glass in building - Determination of the heat transfer coefficient (U-value) - Method with the plate device
DIN EN 675 Glass in building - Determination of the heat transfer coefficient (U-value) - Heat flow meter method
DIN EN 676 Automatic blower burners for gaseous fuels
DIN EN 677 Heating boilers for gaseous fuels - Special requirements for condensing boilers with a nominal heat load less than or equal to 70 kW
DIN EN 678 Determination of the dry bulk density of steam-hardened aerated concrete
DIN EN 679 Determination of the compressive strength of steam-hardened aerated concrete
DIN EN 680 Determination of the shrinkage of steam-hardened aerated concrete
DIN EN 681 elastomer seals - Material requirements for pipe seals for applications in water supply and drainage
- Part 1 Vulcanized rubber
- Part 2 thermoplastic elastomers
- Part 3 Cellular materials made of vulcanized rubber
- Part 4 sealing elements made of cast polyurethane
DIN EN 682 Elastomer seals - Material requirements for seals in supply lines and components for gas and liquid hydrocarbons
DIN EN 683 aluminum and aluminum alloys - primary material for heat exchangers (Finstock)
- Part 1 Technical delivery conditions
- Part 2 mechanical properties
- Part 3 dimensional limits and shape tolerances
DIN EN 684 Resilient floor coverings - Determination of seam strength
DIN EN 686 Resilient floor coverings - Specification for linoleum with and without pattern with foam backing
DIN EN 687 Resilient floor coverings - Specification for linoleum with and without pattern with cork backing
DIN EN 688 Resilient floor coverings - Specification for cork linoleum
DIN EN 689 workplace atmosphere - Instructions for determining the inhalation exposure to chemical substances for comparison with limit values and measurement strategy
DIN EN 690 Agricultural machinery - Manure spreaders - Safety
DIN EN 691 Safety of woodworking machines
- Part 1 Common Requirements
DIN EN 692 Machine tools - Mechanical presses - Safety
DIN EN 693 Machine tools - Safety - Hydraulic presses
DIN EN 694 fire extinguishing hoses - Dimensionally stable hoses for wall hydrants
DIN EN 695 kitchen sinks - connection dimensions
DIN EN 702 Protective clothing - Protection against heat and flames - Test method: Determination of the contact heat transfer through protective clothing or its materials
DIN EN 703 Agricultural machinery - Machines for loading, mixing and / or chopping and distributing silage - Safety
DIN EN 705 Plastics piping systems - Pipes and fittings made of glass fiber reinforced thermosetting plastics (GRP) - Methods for regression analysis and their application
DIN EN 706 Agricultural machinery - Vine leaf cutting devices - Safety
DIN EN 707 agricultural machinery - liquid manure tankers - safety
DIN EN 709 Machinery for agriculture and forestry - Single-axle tractors with attached tiller, tillers, drive wheel hoes - Safety
DIN EN 710 Safety of machines - Safety requirements for foundry machines and systems for mold and core production and associated equipment
DIN EN 711 Inland navigation vehicles - Railings for decks - Requirements, types
DIN EN 712 Thermoplastic piping systems; Tensile mechanical connections between pressure pipes and fittings; Test method for resistance to pull-out under constant load
DIN EN 713 plastic piping systems; Mechanical connections between fittings and pressure pipes made of polyolefins; Test method for tightness under internal pressure and bending
DIN EN 714 Pipeline systems made of thermoplastics - Non-tensile connections with elastomeric sealing rings between pressure pipes and fittings - Test method for tightness under hydrostatic internal pressure without axial loading
DIN EN 715 piping systems made of thermoplastics; Tensile connections between pressure pipes and fittings with small diameters; Test method for tightness under internal pressure by means of water and under axial load
DIN EN 716 furniture - cots and travel cots for living areas
- Part 1 Safety requirements
- Part 2 test method
DIN EN 717 Wood-based panels - Determination of the formaldehyde release
- Part 1 formaldehyde release according to the test chamber method
- Part 2 release of formaldehyde according to the gas analysis method
- Part 3 formaldehyde release according to the bottle method
DIN EN 718 Resilient floor coverings - Determination of the mass per unit area of reinforcement or backing of floor coverings made of polyvinyl chloride
DIN EN 720 Transportable gas cylinders - gases and gas mixtures
- Part 1 properties of single gases
DIN EN 721 Habitable recreational vehicles - Requirements for safety ventilation
DIN EN 722 Habitable recreational vehicles - Heating systems operated with liquid fuel
- Part 1 caravans and mobile homes
DIN EN 723 Copper and copper alloys - Method for determining the carbon content on the inner surface of copper pipes or fittings by burning
DIN EN 725 high-performance ceramics - test method for ceramic powders
- Part 1 Determination of impurities in aluminum oxide powder
- Part 2 Determination of impurities in barium titanate powders
- Part 3 Determination of the oxygen content in non-oxide powders by means of carrier gas hot extraction
- Part 4 Determination of the oxygen content in aluminum nitride powders using X-ray fluorescence analysis (XRF)
- Part 5 Determination of the particle size distribution
- Part 8 Determination of the tapped bulk density
- Part 9 Determination of the bulk density
- Part 10 Determination of the compaction properties
- Part 11 Determination of the compression behavior with natural sinter firing
- Part 12 Chemical analysis of zirconium oxide
DIN EN 726 identification card systems - requirements for chip cards and end devices for telecommunication purposes
- Part 1 system overview
- Part 2 security framework
- Part 3 Application-independent requirements for the card
- Part 4 Application-independent, card-relevant requirements for end devices
- Part 5 payment methods
- Part 6 performance characteristics
- Part 7 security module
DIN EN 727 Plastic piping and protective pipe systems - Pipes and fittings made of thermoplastics - Determination of the Vicat softening temperature (VST)
DIN EN 728 Plastic piping and protective pipe systems - Pipes and fittings made of polyolefins - Determination of the oxidation induction time
DIN EN 730 gas welding devices - safety devices
- Part 1 With integrated flame arrester
- Part 2 Without integrated flame arrester
DIN EN 732 specifications for liquefied gas appliances - absorber refrigerators
DIN EN 733 centrifugal pumps with axial inlet PN 10 with bearing bracket - nominal power, main dimensions, designation system
DIN EN 734 side channel pumps PN 40 - nominal output, main dimensions, designation system
DIN EN 735 Connection dimensions for centrifugal pumps - tolerances
DIN EN 736 fittings - terminology
- Part 1 Definition of the basic types
- Part 2 Definition of the valve parts
- Part 3 definition of terms
DIN EN 741 Continuous conveyors and systems - Safety requirements for systems and their components for the pneumatic conveyance of bulk goods
DIN EN 744 Plastic piping and protective pipe systems - Pipes made of thermoplastics - Test method for the resistance to external impact stress in the circumferential method
DIN EN 746 industrial thermoprocessing systems
- Part 1 General safety requirements for industrial thermoprocessing systems
- Part 2 Safety requirements for furnaces and fuel supply systems
- Part 3 Safety requirements for the generation and use of protective and reaction gases
- Part 4 Special safety requirements for hot-dip galvanizing plants
- Part 5 Special safety requirements for salt bath heat treatment facilities and systems
- Part 6 Special safety requirements for systems for liquid phase treatment (draft)
- Part 7 special safety requirements for vacuum thermoprocessing systems (draft)
- Part 8 Special safety requirements for quenching systems
DIN EN 747 furniture - bunk beds and loft beds
- Part 1 requirements for safety, strength and durability
- Part 2 test method
DIN EN 748 Playing field equipment - Football goals - Functional and safety requirements, test methods
DIN EN 749 playground equipment - handball goals - functional and safety requirements, test methods
DIN EN 750 Playfield equipment - Hockey goals - Functional and safety requirements, test methods
DIN EN 751 sealant for metal threaded connections in contact with gases of the 1st, 2nd and 3rd family and hot water
- Part 1 Anaerobic Sealants
- Part 2 Non-hardening sealants
- Part 3 Unsintered PTFE tapes
DIN EN 752 drainage systems outside of buildings
DIN EN 754 aluminum and aluminum alloys - drawn rods and tubes
- Part 1 Technical delivery conditions
- Part 2 mechanical properties
- Part 3 round bars, dimensions and shape tolerances
- Part 4 square bars, limit dimensions and shape tolerances
- Part 5 rectangular bars, dimensional limits and shape tolerances
- Part 6 hexagonal bars, dimensional limits and shape tolerances
- Part 7 Seamless tubes, dimensional limits and shape tolerances
- Part 8 Pipes extruded with a chamber tool, dimensional limits and shape tolerances
DIN EN 755 Aluminum and aluminum alloys - Extruded bars, tubes and profiles
- Part 1 Technical delivery conditions
- Part 2 mechanical properties
- Part 3 round bars, dimensions and shape tolerances
- Part 4 square bars, limit dimensions and shape tolerances
- Part 5 rectangular bars, dimensional limits and shape tolerances
- Part 6 hexagonal bars, dimensional limits and shape tolerances
- Part 7 Seamless tubes, dimensional limits and shape tolerances
- Part 8 Pipes extruded with a chamber tool, dimensional limits and shape tolerances
- Part 9 profiles, dimensional limits and shape tolerances
DIN EN 761 Plastics piping systems - Pipes made of glass fiber reinforced thermosetting plastics (GRP) - Determination of the creep factor in the dry state
DIN EN 764 pressure equipment
- Part 1 vocabulary
- Part 2 sizes, symbols and units
- Part 3 Definition of the parties involved
- Part 4 Creation of technical delivery conditions for metallic materials
- Part 5 test certificates for metallic materials and compliance with the material specification
- Part 7 safety devices for unfired pressure equipment
DIN EN 765 Sacks for the transport of food for food aid - Sacks made from polyolefin fabrics other than polypropylene
DIN EN 766 Sacks for the transport of food for food aid - Sacks made of jute fabric
DIN EN 767 Sacks for the transport of food for food aid - Sacks made of a jute / polyolefin blend
DIN EN 768 Sacks for the transport of food for food aid - Bags made of cotton fabric with inner sack
DIN EN 769 Bags for the transport of food for food aid - Bags made of a cotton / polyolefin blend
DIN EN 770 bags for the transport of food for food aid - paper bags
DIN EN 771 specifications for bricks
- Part 1 masonry bricks
- Part 2 sand-lime bricks
- Part 3 bricks made of concrete (with dense and porous aggregates)
- Part 4 aerated concrete blocks
- Part 5 concrete blocks
- Part 6 natural stones
DIN EN 772 test method for bricks
- Part 1 Determination of compressive strength
- Part 2 Determination of the percentage of holes in bricks (by means of paper printing)
- Part 3 Determination of the net volume and the percentage of holes in masonry bricks by means of hydrostatic weighing (underwater weighing)
- Part 4 Determination of the density and the bulk density as well as the total porosity and the open porosity of masonry blocks made of natural stone
- Part 5 Determination of the content of active soluble salts of masonry bricks
- Part 6 Determination of the flexural strength of concrete bricks
- Part 7 Determination of the water absorption of masonry bricks for damp insulating layers by storage in boiling water
- Part 9 Determination of the perforated and net volume as well as the percentage perforated proportion of masonry bricks and sand-lime bricks by means of sand filling
- Part 10 Determination of the moisture content of sand-lime bricks and masonry bricks made of aerated concrete
- Part 11 Determination of the capillary water absorption of masonry blocks made of concrete, aerated concrete blocks, concrete blocks and natural stones as well as the initial water absorption of masonry bricks
- Part 13 Determination of the net and gross dry bulk density of masonry stones (except natural stones)
- Part 14 Determination of the moisture-related deformation of masonry blocks made of concrete and cast stone
- Part 15 Determination of the water vapor permeability of aerated concrete blocks
- Part 16 Determination of the dimensions
- Part 18 Determination of the frost resistance of sand-lime bricks
- Part 19 Determination of the moisture expansion of horizontally perforated large masonry bricks
- Part 20 Determination of the flatness of bricks
- Part 21 Determination of the cold water absorption of masonry bricks and sand-lime bricks
DIN EN 774 garden tools - Portable motorized hedge trimmers - Safety, January 2010 replaced by DIN EN ISO 10517
DIN EN 777 dark radiator systems with several burners with blower for commercial and industrial use
- Part 1 System D - Security
- Part 2 System E - Security
- Part 3 System F - Security
- Part 4 System H - Security
DIN EN 778 Gas-fired warm air generators with forced convection for heating rooms for domestic use with a nominal heat load not exceeding 70 kW, without a fan to convey the combustion air and / or the exhaust gases
DIN EN 779 Particle air filters for general ventilation technology - Determination of the filter performance
DIN EN 786 garden tools - Electrically operated hand-held and hand-held lawn trimmers and lawn edge trimmers - Mechanical safety
DIN EN 787 Sacks for the transport of food for food aid - Bags made of polyethylene film
DIN EN 788 Sacks for the transport of food for food aid - tubular bag packaging made of composite film
DIN EN 789 Timber structures - Test methods - Determination of the mechanical properties of wood-based materials
DIN EN 790 Inland navigation vehicles - Staircases with inclination angles of 45 ° to 60 ° - Requirements, types
DIN EN 791 drilling rigs - safety
DIN EN 792 Hand-held non-electrically operated machines - Safety requirements
- Part 13 driving tools
DIN EN 794 lung ventilators
- Part 3 Special requirements for emergency and transport ventilators
DIN EN 795 Personal fall protection equipment - Anchor devices
DIN EN 802 Plastic piping and protective pipe systems - Injection-molded fittings made of thermoplastics for pressure pipes - Test method for maximum deformation due to crushing
DIN EN 803 Plastic piping systems - Injection-molded fittings made of thermoplastics for push-in socket connections for pressure pipelines - Test method for the resistance to short-term internal pressure without axial loading
DIN EN 804 Plastic piping systems - Injection molded fittings with adhesive socket connections for pressure pipelines - Test method for the resistance to short-term hydrostatic internal pressure
DIN EN 805 water supply - Requirements for water supply systems and their components outside of buildings
DIN EN 806 Technical rules for drinking water installations (TRWI)
- Part 1 General
- Part 2 planning
- Part 3 Calculation of the inner pipe diameter - Simplified procedure
- Part 4 installation
- Part 5 Operation and Maintenance
DIN EN 809 Pumps and pump units for liquids - General safety requirements
DIN EN 818 Short link round link chains for lifting purposes - Safety
- Part 1 General Terms of Acceptance
- Part 2 medium-tolerance round steel chains for chain slings - quality class 8
- Part 3 medium-tolerance round steel chains for chain slings - quality class 4
- Part 4 chain slings - grade 8
- Part 5 chain slings - quality class 4
- Part 6 chain slings - stipulations on information about use and maintenance to be made available by the manufacturer
- Part 7 Fine-tolerance hoist chains, quality class T (version T, DAT and DT)
DIN EN 821 high-performance ceramics - monolithic ceramics - thermophysical properties
- Part 1 Determination of the thermal change in length
- Part 2 Measurement of the thermal diffusivity with the laser flash (or heat pulse) method
- Part 3 Determination of the specific heat capacity
DIN EN 822 Thermal insulation materials for building applications - Determination of length and width
DIN EN 823 Thermal insulation materials for building applications - Determination of thickness
DIN EN 824 Thermal insulation materials for building applications - Determination of squareness
DIN EN 825 Thermal insulation materials for building applications - Determination of evenness
DIN EN 826 Thermal insulation materials for the building industry - Determination of the behavior under pressure
DIN EN 827 Adhesives - Determination of the solids content by agreement and up to constant mass
DIN EN 828 Adhesives - Wettability - Determination by measuring the contact angle and the surface free energy of solid surfaces
DIN EN 832 Thermal behavior of buildings - Calculation of heating energy demand - Residential buildings, June 2003 replaced by DIN EN 832, DIN EN ISO 13790, DIN EN ISO 13790
DIN EN 834 heat cost allocators for recording the consumption values of space heating surfaces - devices with electrical energy supply
DIN EN 835 heat cost allocators for recording the consumption values of space heating surfaces - devices without electrical energy supply based on the evaporation principle
DIN EN 836 Garden tools - Motor-driven lawn mowers - Safety
DIN EN 837 pressure gauges
- Part 1 pressure gauges with Bourdon tubes; Dimensions, measurement technology, requirements and testing
- Part 2 Selection and installation recommendations for pressure gauges
- Part 3 pressure gauges with plate and capsule springs; Dimensions, measurement technology, requirements and testing
DIN EN 838 Exposure at the workplace - Measurement of gases and vapors with diffusion collectors - Requirements and test methods
DIN EN 840 Mobile waste and recyclable containers
- Part 1 container with 2 wheels and a nominal volume of up to 400 l for comb dumps - dimensions and shape
- Part 2 container with 4 wheels and a nominal volume of up to 1,300 l with flat lid (s), for dumps with pin receptacle and / or for dump dumps - dimensions and shape
- Part 3 container with 4 wheels and a nominal volume of up to 1,300 l with sliding lid (s), for dumps with pin receptacle and / or for dumps - dimensions and shape
- Part 4 container with 4 wheels and a nominal volume of up to 1 700 l with flat lid (s), for wide fillings with spigot mount or BG fillings and / or for wide comb fillings - dimensions and shape
- Part 5 Requirements for execution and test methods
- Part 6 Safety and Health Protection Requirements
DIN EN 841 bar coding - symbology specifications, description of formats
DIN EN 842 Safety of machines - Optical danger signals - General requirements, design and testing
DIN EN 843 high-performance ceramics - mechanical properties of monolithic ceramics at room temperature
- Part 1 Determination of flexural strength
- Part 2 Determination of the modulus of elasticity, shear modulus and Poisson's number
- Part 3 Determination of the parameters of the subcritical crack growth from flexural strength tests with constant stress rate
- Part 4 hardness test according to Vickers, Knoop and Rockwell
- Part 5 Statistical Evaluation
- Part 6 Guideline for Fractographic Examination
- Part 7 C-ring tests
- Part 8 guidelines for carrying out overload tests
DIN EN 844 Round and sawn timber - Terminology
- Part 1 Common general terms about logs and sawn timber
- Part 2 General terms about logs
- Part 3 General terms about sawn timber
- Part 4 Terms to the moisture content
- Part 5 Terms to measure logs
- Part 6 Terms to dimensions of sawn timber
- Part 7 Terms for the anatomical structure of wood
- Part 8 Terms to characteristics of round timber
- Part 9 Terms to characteristics of sawn timber
- Part 10 terms on discoloration and fungal attack
- Part 11 terms for insect infestation
- Part 12 Additional terms and general index
DIN EN 845 specifications for supplementary components for masonry
- Part 1 wall anchors, ties , supports and consoles
- Part 2 falls
- Part 3 horizontal joint reinforcement made of steel
DIN EN 846 test method for supplementary components for masonry
- Part 2 Determination of the bond strength of prefabricated bed joint reinforcement
- Part 3 Determination of the shear resistance of the welds in prefabricated bed joint reinforcement
- Part 4 Determination of the strength and the load-deformation properties of tapes
- Part 5 Determination of tensile and compressive strength and rigidity of wall anchors (brick pair test)
- Part 6 Determination of tensile and compressive strength and rigidity of wall anchors (one-sided test)
- Part 7 Determination of the shear resistance and the rigidity of wall connectors (stone pair test in mortar joints)
- Part 8 Determination of the load-bearing capacity and the load-deformation properties of beam supports
- Part 9 Determination of the bending and shear resistance of falls
- Part 10 Determination of the load-bearing capacity and the load-deformation properties of consoles
- Part 11 Determination of the dimensions and elevation of falls
- Part 13 Determination of the impact strength, the abrasion resistance and the corrosion resistance of organic coatings
- Part 14 Determination of the initial shear strength of the bond between the prefabricated part of a partially prefabricated lintel, which was added on site, and the masonry above the lintel
DIN EN 847 Machine tools for woodworking - Safety requirements
- Part 1 milling and planing tools, circular saw blades
- Part 2 requirements for the shank of milling tools
- Part 3 clamping devices
DIN EN 848 Safety of woodworking machines - Milling machines for one-sided machining with rotating tools
- Part 1 Single-spindle vertical table milling machines
- Part 2 Single-spindle routers with manual feed / mechanical feed
- Part 3 NC drilling and milling machines
DIN EN 851 aluminum and aluminum alloys - circular blanks and blank primary material for the manufacture of kitchenware - specifications
DIN EN 853 Rubber hoses and hose lines - Hydraulic hoses with wire mesh reinforcement - Specification
DIN EN 854 rubber hoses and hose lines - hydraulic hoses with textile insert - specification
DIN EN 855 plastic hoses and hose lines - plastic hydraulic hoses with textile insert - specification
DIN EN 856 Rubber hoses and hose lines - Hydraulic hoses with wire spiral insert - Specification
DIN EN 857 Rubber hoses and hose lines - Compact hydraulic hoses with wire mesh reinforcement - Specification
DIN EN 858 separator systems for light liquids (e.g. oil and gasoline)
- Part 1 construction, function and testing principles, labeling and quality control
- Part 2 Choice of nominal size, installation, operation and maintenance
DIN EN 859 Safety of woodworking machines - surface planing machines with manual feed
DIN EN 860 Safety of woodworking machines - Thickness planers for one-sided processing
DIN EN 861 Safety of woodworking machines - Combined planing and thicknessing machines
DIN EN 862 Packaging - Child-resistant packaging - Requirements and test methods for non-resealable packaging for non-pharmaceutical products
DIN EN 863 Protective clothing - Mechanical properties - Test method: Resistance to puncture
DIN EN 867 Non-biological systems for use in sterilizers
- Part 5 Specification of indicator systems and test bodies for the performance test of small sterilizers of type B and type S
DIN EN 868 packaging for medical products to be sterilized in the final packaging
- Part 2 Sterilization packaging - Requirements and test methods
- Part 3 Paper for the manufacture of paper bags (specified in EN 868-4) and for the manufacture of transparent bags and tubes (specified in EN 868-5) - Requirements and test methods
- Part 4 paper bags - Requirements and test methods
- Part 5 Sealable transparent bags and tubes made of porous materials and plastic composite film - Requirements and test methods
- Part 6 paper for low temperature sterilization processes - requirements and test methods
- Part 7 Adhesive-coated paper for low-temperature sterilization processes - Requirements and test methods
- Part 8 Reusable sterilization containers for steam sterilizers according to EN 285 - requirements and test methods
- Part 9 Uncoated nonwoven materials made of polyolefins - Requirements and test methods
- Part 10 Adhesive-coated nonwoven materials made of polyolefins - Requirements and test methods
DIN EN 869 Safety of machines - Safety requirements for metal die casting systems
DIN EN 872 Water quality - Determination of suspended substances - Procedure by separation using a glass fiber filter
DIN EN 877 Cast iron pipes and fittings, their connections and accessories for the drainage of buildings - Requirements, test methods and quality assurance
DIN EN 878 Products for the treatment of water for human consumption - aluminum sulfate
DIN EN 881 products for the treatment of water for human consumption - aluminum chloride (monomer), aluminum hydroxide chloride (monomer) and aluminum hydroxide chloride sulfate (monomer)
DIN EN 882 products for the treatment of water for human consumption - sodium aluminate
DIN EN 883 Products for the treatment of water for human consumption - polyaluminum chloride hydroxide and polyaluminum chloride hydroxide sulfate
DIN EN 885 Products for the treatment of water for human consumption - Polyaluminium hydroxide chloride silicate
DIN EN 886 Products for the treatment of water for human consumption - Polyaluminium hydroxide silicate sulfate
DIN EN 887 products for the treatment of water for human consumption - aluminum-iron (III) -sulphate
DIN EN 888 Products for the treatment of water for human consumption - iron (III) chloride
DIN EN 889 Products for the treatment of water for human consumption - Iron (II) sulfate
DIN EN 890 products for the treatment of water for human consumption - iron (III) sulfate solution
DIN EN 891 Products for the treatment of water for human consumption - Iron (III) chloride sulfate
DIN EN 892 Mountaineering equipment - Dynamic mountain ropes - Safety requirements and test methods
DIN EN 893 Mountaineering equipment - Crampons - Safety requirements and test methods
DIN EN 894 Safety of machines - Ergonomic requirements for the design of displays and control elements
- Part 1 General principles for user interaction with displays and controls
- Part 2 ads
- Part 3 controls
- Part 4 Position and arrangement of displays and controls
DIN EN 896 Products for the treatment of water for human consumption - sodium hydroxide
DIN EN 897 Products for the treatment of water for human consumption - sodium carbonate
DIN EN 898 Products for the treatment of water for human consumption - Sodium hydrogen carbonate
DIN EN 899 Products for the treatment of water for human consumption - sulfuric acid
DIN EN 900 products for the treatment of water for human consumption - calcium hypochlorite
DIN EN 901 products for the treatment of water for human consumption - sodium hypochlorite
DIN EN 902 products for the treatment of water for human consumption - hydrogen peroxide
DIN EN 903 water quality; Determination of anionic surface-active substances by measuring the methylene blue index MBAS (ISO 7875-1: 1984, modified)
DIN EN 908 Agricultural and forestry machines - Irrigation machines with hose reels - Safety
DIN EN 909 Agricultural and forestry machines - Circular and linear irrigation machines - Safety
DIN EN 911 plastic piping systems - Connections with elastomeric sealing rings and mechanical connections for pressure pipelines made of thermoplastics - Test methods for tightness under external hydrostatic pressure
DIN EN 912 Wood fasteners - Specifications for special type of dowels for wood
DIN EN 913 gymnastics equipment - General safety requirements and test methods
DIN EN 914 Gymnastics equipment - Bars and combined uneven bars / parallel bars - Requirements and test methods including safety
DIN EN 915 Gymnastics equipment - Uneven bars - Requirements and test methods including safety
DIN EN 916 Gymnastics equipment - Vaulting boxes - Requirements and test methods including safety
DIN EN 917 Plastics piping systems - Valves made from thermoplastics - Test method for resistance to internal pressure and tightness
DIN EN 920 Paper and cardboard, intended for contact with food - Determination of the dry content in an aqueous extract
DIN EN 923 adhesives - terms and definitions
DIN EN 924 Adhesives - Solvent-based and solvent-free adhesives - Determination of the flash point
DIN EN 926 equipment for paragliding - paragliders
- Part 1 Requirements and test methods for structural strength
- Part 2 Requirements and test methods for the classification of the safety-relevant flight characteristics
DIN EN 927 Coating materials - Coating materials and coating systems for wood in outdoor areas
- Part 1 classification and selection
- Part 2 performance requirements
- Part 3 outdoor exposure
- Part 5 Assessment of the water permeability
- Part 6 Artificial weathering of wood coatings with fluorescent UV lamps and water
DIN EN 929 Inland navigation vehicles; Push convoys; Mast holder for detachable signal masts
DIN EN 930 Machines for the production of shoes, leather and imitation leather goods - Roughening, clearing, polishing and edge processing machines - Safety requirements
DIN EN 931 Machines for the production of shoes - Lasting machines - Safety requirements
DIN EN 932 test method for general properties of aggregates
- Part 1 sampling procedure
- Part 2 procedure for concentrating laboratory samples
- Part 3 Implementation and terminology of a simplified petrographic description
- Part 5 General test equipment and calibration
- Part 6 Definitions for the repeatability and comparative precision
DIN EN 933 test method for geometric properties of aggregates
- Part 1 Determination of the particle size distribution - sieving method
- Part 2 Determination of the particle size distribution; Test sieves, nominal dimensions of the sieve openings
- Part 3 Determination of the grain shape - flatness index
- Part 4 Determination of the grain shape - grain shape index
- Part 5 Determination of the proportion of broken grains in coarse aggregates
- Part 6 Flow coefficient of aggregates
- Part 7 Determination of the mussel shell content; Percentage of mussel shells in coarse aggregates
- Part 8 Assessment of fine fractions - sand equivalent method
- Part 9 Assessment of fines - methylene blue method
- Part 10 assessment of fine fractions - particle size distribution of filler (air jet sieving)
- Part 11 Classification of the components in coarse recycled aggregates
DIN EN 934 admixtures for concrete, mortar and grout
- Part 1 Common Requirements
- Part 2 Concrete admixtures - Definitions, requirements, conformity, marking and labeling
- Part 3 Additives for masonry mortar - Definitions, requirements, conformity, marking and labeling
- Part 4 Admixtures for grout for tendons - Definitions, requirements, conformity, marking and labeling
- Part 5 admixtures for shotcrete - terms, requirements, conformity, marking and labeling
- Part 6 Sampling, conformity control and evaluation of conformity
DIN EN 935 products for the treatment of water for human consumption - aluminum-iron (III) chloride (monomer) and aluminum-iron (III) hydroxide chloride (monomer)
DIN EN 936 Products for the treatment of water for human consumption - carbon dioxide
DIN EN 937 products for the treatment of water for human consumption - chlorine
DIN EN 938 Products for the treatment of water for human consumption - sodium chlorite
DIN EN 939 Products for the treatment of water for human consumption - hydrochloric acid
DIN EN 940 Safety of woodworking machines - Combined woodworking machines
DIN EN 941 Aluminum and aluminum alloys - Circular blanks and blank primary material for general applications - Specifications
DIN EN 942 Wood in carpentry work - General requirements
DIN EN 943 Protective clothing against liquid and gaseous chemicals, including liquid aerosols and solid particles
- Part 1 Performance requirements for type 1 (gas-tight) chemical protective clothing
- Part 2 performance requirements for gas-tight (type 1) chemical protective suits for emergency teams (ET)
DIN EN 947 swing doors - Determination of the resistance to vertical loads
DIN EN 948 swing doors - determination of the resistance to static torsion
DIN EN 949 Windows, doors, revolving and roller shutters, curtain walls - Determination of the resistance of doors to impact from a soft and heavy impact body
DIN EN 950 door leaves - Determination of the resistance to hard impact
DIN EN 951 door leaves - measurement method for determining height, width, thickness and squareness
DIN EN 952 Door leaves - General and local evenness - Measurement method
DIN EN 953 Safety of machines - Separating protective devices - General requirements for the design and construction of fixed and movable separating protective devices
DIN EN 957 stationary training equipment
- Part 1 General safety requirements and test methods
- Part 2 strength training equipment, additional special safety requirements and test methods
- Part 4 strength training benches, additional special safety requirements and test methods
- Part 5 Stationary training bicycles and crank training devices for the upper body, additional special safety requirements and test methods
- Part 6 treadmills, additional special safety requirements and test methods
- Part 7 rowing machines, additional special safety requirements and test methods
- Part 8 Steppers, stair climbing devices and climbers - Additional special safety requirements and test methods
- Part 9 elliptical trainer, additional special safety requirements and test methods
- Part 10 training bicycles with rigid drive or without freewheel, additional special safety requirements and test methods
DIN EN 958 Mountaineering equipment - Shock absorbers for use on via ferrata - Safety requirements and test methods
DIN EN 959 mountaineering equipment - bolts - safety requirements and test methods
DIN EN 960 test heads for testing protective helmets
DIN EN 966 air sports helmets
DIN EN 969 Pipes, fittings, accessories made of ductile cast iron and their connections for gas lines - Requirements and test methods
DIN EN 972 Tannery machines - Roller machines - Safety requirements
DIN EN 973 Products for the treatment of water for human consumption - Sodium chloride for the regeneration of ion exchangers
DIN EN 974 Products for the treatment of water for human consumption - phosphoric acid
DIN EN 975 Sawn timber - grading according to the appearance of hardwood
- Part 1 oak and beech
- Part 2 poplar
DIN EN 976 Underground tanks made of textile-glass reinforced plastics (GRP) - Horizontal cylindrical tanks for the pressureless storage of liquid fuels based on petroleum
- Part 1 Requirements and test methods for single-walled tanks
- Part 2 Transport, handling, temporary storage and installation of single-walled tanks
DIN EN 977 Underground tanks made of textile-glass-reinforced plastics (GRP) - test arrangement for one-sided exposure to fluids
DIN EN 978 Underground tanks made of textile-glass reinforced plastics (GRP) - Determination of the factor a and the factor ß
DIN EN 981 Safety of machines - System of acoustic and optical danger signals and information signals
DIN EN 984 Textile floor coverings - Determination of the wear layer weight of needled floor coverings
DIN EN 985 Textile floor coverings - chair castor test
DIN EN 986 Textile floor coverings - Tiles - Determination of dimensional changes due to the effects of changing humidity and temperature conditions and vertical surface deformation
DIN EN 988 Zinc and zinc alloys - Requirements for rolled flat products for the building industry
DIN EN 989 Determination of the bond behavior between rebar and steam-hardened aerated concrete with the help of the push-out test
DIN EN 990 test method for checking the corrosion protection of the reinforcement in steam-hardened aerated concrete and in lightweight concrete with pore structure
DIN EN 991 Determination of the dimensions of prefabricated reinforced components made of steam-hardened aerated concrete or lightweight concrete with pore structure
DIN EN 992 Determination of the dry bulk density of lightweight concrete with pore structure
DIN EN 993 test method for tightly formed refractory products
- Part 1 Determination of the bulk density, open porosity and total porosity
- Part 2 Determination of the density
- Part 3 tests for products containing carbon
- Part 4 Determination of gas permeability
- Part 5 Determination of the cold compressive strength
- Part 6 Determination of the flexural strength at room temperature
- Part 7 Determination of the flexural strength at elevated temperatures
- Part 9 Determination of the pressure flow behavior
- Part 10 Determination of the permanent change in length after exposure to temperature
- Part 11 Determination of the thermal shock resistance
- Part 12 Determination of the cone drop point (fire resistance)
- Part 13 Specifications for reference cones for laboratory use
- Part 15 Determination of the thermal conductivity according to the hot wire (parallel) method
- Part 16 Determination of the resistance to sulfuric acid
- Part 17 Determination of the bulk density of granular material according to the mercury displacement method under vacuum
- Part 18 Determination of the bulk density of granular material by the water displacement method under vacuum
- Part 19 Determination of thermal expansion by a differential method
DIN EN 995 Textile floor coverings - Determination of the deformability of backing coatings ("cold flow")
DIN EN 996 pile driving equipment - safety requirements
DIN EN 997 toilet bowl with molded odor trap
DIN EN 998 specifications for mortar in masonry
- Part 1 plaster mortar
- Part 2 masonry mortar

DIN EN 1000-1999

DIN EN 1001 Durability of wood and wood products - terminology
- Part 1 List of equivalent technical terms
- Part 2 vocabulary
DIN EN 1004 Mobile working platforms made of prefabricated components - materials, dimensions, load assumptions and safety requirements
DIN EN 1005 Safety of machines - Human physical performance
- Part 1 terms
- Part 2 Manual handling of objects in connection with machines and machine parts
- Part 3 Recommended force limits when operating the machine
- Part 4 Assessment of postures and movements when working on machines
- Part 5 Risk assessment for short-cycle activities with high handling frequencies
DIN EN 1006 High-performance ceramics - Monolithic ceramics - Guideline for the selection of samples for the assessment of properties
DIN EN 1007 high-performance ceramics - ceramic composite materials; Procedure for testing fiber reinforcements
- Part 1 Determination of the size content
- Part 2 Determination of the fineness
- Part 3 Determination of the fiber diameter and cross section
- Part 4 Determination of tensile properties of fibers at room temperature
- Part 5 Determination of the distribution of tensile strength and tensile elongation of fibers in the fiber bundle at room temperature
- Part 6 Determination of tensile properties of fibers at high temperature
- Part 7 Determination of the distribution of tensile strength and tensile elongation of fibers in the fiber bundle at high temperature
DIN EN 1008 additional water for concrete - Specification for sampling, testing and assessment of the suitability of water, including water that occurs during concrete production, as additional water for concrete
DIN EN 1010 Safety of machines - Safety requirements for the design and construction of printing and paper converting machines
- Part 1 Common Requirements
- Part 2 Printing and varnishing machines including prepress machines
- Part 3 cutting machines
- Part 4 bookbinding, paper processing and paper finishing machines
- Part 5 Corrugated cardboard production, flat and corrugated cardboard processing machines
DIN EN 1011 welding - Recommendations for welding metallic materials
- Part 1 General instructions for arc welding
- Part 2 arc welding of ferritic steels
- Part 3 arc welding of stainless steels
- Part 4 arc welding of aluminum and aluminum alloys
- Part 5 welding of clad steels
- Part 6 laser beam welding
- Part 7 electron beam welding
- Part 8 welding of cast iron
DIN EN 1012 compressors and vacuum pumps - safety requirements
- Part 1 compressors
- Part 2 vacuum pumps
DIN EN 1013 Translucent, single-skin, profiled sheets made of plastic for indoor and outdoor use on roofs, walls and ceilings - requirements and test methods
DIN EN 1014 Wood preservatives - Creosote (tar impregnation oil) and wood impregnated with it - Sampling and analysis
- Part 1 method for sampling creosote
- Part 2 method for sampling creosote from impregnated wood for subsequent analysis
- Part 3 Determination of the benzo [ a ] pyrene content in creosote
- Part 4 Determination of the content of water-extractable phenols in creosote
DIN EN 1015 test method for mortar for masonry
- Part 1 Determination of the grain size distribution (by sieve analysis)
- Part 2 sampling of mortars and production of test mortars
- Part 3 Determination of the consistency of fresh mortar (with spreading table)
- Part 4 Determination of the consistency of fresh mortar (with penetration device)
- Part 6 Determination of the bulk density of fresh mortar
- Part 7 Determination of the air content of fresh mortar
- Part 9 Determination of the workability time and the correctability time of fresh mortar
- Part 10 Determination of the dry density of solid mortar
- Part 11 Determination of the flexural strength and compressive strength of solid mortar
- Part 12 Determination of the adhesive strength of hardened plaster mortars
- Part 17 Determination of the content of water-soluble chloride in fresh mortar
- Part 18 Determination of the capillary water absorption of hardened mortar (solid mortar)
- Part 19 Determination of the water vapor permeability of solid mortars made from plaster mortars
- Part 21 Determination of the compatibility of single-layer plastering mortars with substrates
DIN EN 1017 Products for the treatment of water for human consumption - Semi-burnt dolomite
DIN EN 1018 Products for the treatment of water for human consumption - calcium carbonate
DIN EN 1019 Products for the treatment of water for human consumption - sulfur dioxide
DIN EN 1020 Gas-fired warm air heaters with increased convection for non-domestic use with a nominal heat load not exceeding 300 kW, with a fan for conveying combustion air and / or exhaust gases
DIN EN 1021 Furniture - Assessment of the flammability of upholstered furniture
- Part 1 Smoldering cigarette as an ignition source
- Part 2 A gas flame comparable to a match as an ignition source
DIN EN 1022 Home furniture - Seating furniture - Determination of stability
DIN EN 1023 office furniture - room dividing elements
- Part 1 dimensions
- Part 2 Mechanical safety requirements
- Part 3 exam
DIN EN 1024 Clay roof tiles for overlapping laying - Determination of the geometric parameters
DIN EN 1026 Windows and doors - Air permeability - Test method
DIN EN 1027 Windows and doors - Watertightness against driving rain - Test method
DIN EN 1028 fire extinguishing pumps - centrifugal fire extinguishing pumps with ventilation device
- Part 1 Classification - General and Safety Requirements
- Part 2 Determination of compliance with general and safety requirements
DIN EN 1032 Mechanical vibrations - Test method for moving machines for the purpose of determining the vibration emission value
DIN EN 1034 Safety of machines - Safety requirements for the design and construction of paper making machines and finishing
- Part 1 Common Requirements
- Part 2 debarking drums
- Part 3 rewinder and winder
- Part 4 pulper and their loading devices
- Part 5 sheeter
- Part 6 calender
- Part 7 laid paper
- Part 8 grinding plants
- Part 13 machines for dewiring bales and units
- Part 14 roll splitting machines
- Part 16 paper and board machines
- Part 17 tissue machines
- Part 21 coating machines
- Part 22 wood grinder
- Part 26 roll packaging machines
- Part 27 roller transport systems
DIN EN 1035 Tannery machines - Machines with moving plates - Safety requirements
DIN EN 1036 Glass in Building - Mirrors made of silver-coated float glass for indoor use
- Part 1 Terms, requirements and test methods
- Part 2 Conformity Assessment - Product Standard
DIN EN 1037 Safety of machines - Avoidance of unexpected starts
DIN EN 1038 Identification card systems - Telecommunication applications - Telephones with payment function using chip cards
DIN EN 1040 Chemical disinfectants and antiseptics - Quantitative suspension test to determine the bactericidal effect (basic test) of chemical disinfectants and antiseptics - Test method and requirements (phase 1)
DIN EN 1041 Provision of information by the manufacturer of medical devices
DIN EN 1045 Brazing - Flux for brazing - Classification and technical delivery conditions
DIN EN 1047 Secure storage units - Classification and methods for testing resistance to fire
- Part 1 data cabinets and diskette inserts
- Part 2 data rooms and data storage containers
DIN EN 1048 heat exchangers - Air-cooled liquid coolers "dry cooling towers" - test methods for determining performance
DIN EN 1049 textiles; Tissue; Construction investigation procedure
- Part 2 Determination of the number of threads per unit of length
DIN EN 1050 Safety of machines, principles for risk assessment, December 2007 replaced by DIN EN ISO 14121-1
DIN EN 1052 test method for masonry
- Part 1 Determination of compressive strength
- Part 2 Determination of the flexural strength
- Part 3 Determination of the initial shear strength (adhesive shear strength)
- Part 4 Determination of the shear strength in a moisture barrier layer
- Part 5 Determination of the flexural tensile strength
- Part 10 Supplementary Provisions
DIN EN 1053 Plastic piping systems - Piping systems made of thermoplastics for pressureless applications - Test methods for water tightness
DIN EN 1054 Plastics piping systems - Piping systems made of thermoplastics for sewage pipes for the discharge of domestic sewage - Test methods for the gas tightness of connections
DIN EN 1055 Plastic piping systems - Piping systems made of thermoplastics for sewage pipes inside buildings - Test methods for temperature resistance
DIN EN 1057 Copper and copper alloys - Seamless round tubes made of copper for water and gas pipes for plumbing and heating systems
DIN EN 1058 Wood-based panels - Determination of the characteristic 5% quantile values and the characteristic mean values
DIN EN 1060 non-invasive blood pressure monitors
- Part 3 Supplementary requirements for electromechanical blood pressure measuring systems
- Part 4 test method for determining the measurement accuracy of automatic non-invasive blood pressure monitors
DIN EN 1062 Coating materials - Coating materials and coating systems for mineral substrates and concrete in outdoor areas
- Part 1 classification
- Part 3 Determination of the water permeability
- Part 6 Determination of the carbon dioxide diffusion current density (permeability)
- Part 7 Determination of the crack-bridging properties
- Part 11 Procedures for Pre-Exam Conditioning
DIN EN 1063 Glass in Building - Special Security Glazing - Test method and classification for resistance to bullets
DIN EN 1064 Medical informatics - Standard communication protocol - Computerized electrocardiography
DIN EN 1065 props made of steel with extraction device - product specification, dimensioning and verification by calculation and tests
DIN EN 1067 Adhesives - Examination and preparation of samples for testing
DIN EN 1068 Medical informatics - Registration of coding schemes
DIN EN 1069 water slides
- Part 1 Safety requirements and test methods
- Part 2 notes
DIN EN 1071 high-performance ceramics - method for testing ceramic layers
- Part 1 Determination of the layer thickness with a contact profilometer
- Part 2 Determination of the layer thickness with the dome grinding method
- Part 3 Determination of the adhesion and forms of mechanical failure with the scratch test
- Part 4 Determination of the chemical composition by electron beam micro-range analysis (ESMA)
- Part 6 Determination of the abrasion resistance of layers by means of a micro-abrasion test
- Part 9 Determination of elongation at break
- Part 10 Determination of the layer thickness by means of cross-section
- Part 12 vibration wear test
- Part 13 Determination of the rate of wear by means of a pin-disc test
DIN EN 1073 protective clothing against radioactive contamination
- Part 1 Requirements and test methods for ventilated protective clothing against radioactive contamination by solid particles
- Part 2 Requirements and test methods for unventilated protective clothing against radioactive contamination by solid particles
DIN EN 1074 Valves for water supply - Requirements for usability and their testing
- Part 1 General Requirements
- Part 2 shut-off valves
- Part 3 backflow preventer
- Part 4 ventilation valves with float
- Part 5 control valves
- Part 6 hydrants
DIN EN 1075 wooden structures - test methods - connections with nail plates
DIN EN 1076 Exposure at the workplace - Measurement of gases and vapors with pump-operated sampling devices - Requirements and test methods
DIN EN 1077 helmets for alpine skiers and snowboarders
DIN EN 1078 helmets for cyclists and for users of skateboards and roller skates
DIN EN 1080 shock protection helmets for small children
DIN EN 1081 Resilient floor coverings - Determination of electrical resistance
DIN EN 1082 protective clothing - gloves and arm guards for protection against cuts and stab wounds from hand knives
- Part 1 metal ring braided gloves and arm guards
- Part 2 gloves and arm guards made of materials without metal ring mesh
- Part 3 drop cut test for fabric, leather and other materials
DIN EN 1083 Power-operated brush tools
- Part 1 Definitions and Nomenclature
- Part 2 safety requirements
DIN EN 1085 wastewater treatment - dictionary
DIN EN 1086 Sacks for the transport of food for food aid - Recommendations for the selection of the sack type and the inner sacks in relation to the product to be packed
DIN EN 1087 Chipboard - Determination of moisture resistance
- Part 1 cooking test
DIN EN 1088 Safety of machines - Interlocking devices in connection with separating protective devices - Principles for design and selection
DIN EN 1089 Transportable gas cylinders - Gas cylinder labeling (except for liquid gas (LPG))
- Part 3 color coding
DIN EN 1090 Execution of steel structures and aluminum structures
- Part 1 Conformity verification procedure for load-bearing components
- Part 2 Technical rules for the execution of steel structures
- Part 3 Technical rules for the execution of aluminum structures
DIN EN 1091 negative pressure drainage systems outside of buildings
DIN EN 1092 Flanges and their connections - Round flanges for pipes, fittings, fittings and accessories, designated according to PN
- Part 1 steel flanges
- Part 2 cast iron flanges
- Part 3 flanges made of copper alloys
- Part 4 flanges made of aluminum alloys
DIN EN 1093 Safety of machines - Evaluation of the emission of airborne hazardous substances
- Part 1 Selection of test methods
- Part 2 tracer gas method for measuring the emission rate of a specific air pollutant
- Part 3 test bench method for measuring the emission rate of a certain air pollutant
- Part 4 coverage of a suction system - tracer method
- Part 6 degree of mass separation, diffuse outlet
- Part 7 degree of mass separation, defined outlet
- Part 8 concentration parameters of the air pollutant, test bench method
- Part 9 concentration parameters of the air pollutant, test room method
- Part 11 cleaning index
DIN EN 1094 Fireproof products for thermal insulation purposes
- Part 1 Terminology, classification and test methods for products made from high temperature wool for thermal insulation
- Part 2 Classification of molded products
- Part 4 Determination of the bulk density and total porosity of molded products
- Part 6 Determination of the permanent change in length of molded products after exposure to temperature
DIN EN 1096 Glass in building - Coated glass
- Part 1 Definitions and Classification
- Part 2 requirements and test methods for coatings of classes A, B and S
- Part 3 Requirements and test methods for coatings of classes C and D
- Part 4 conformity assessment / product standard
DIN EN 1097 test method for mechanical and physical properties of aggregates
- Part 1 Determination of the resistance to wear (Micro-Deval)
- Part 2 method for determining the resistance to shattering
- Part 3 Determination of bulk density and voids content
- Part 4 Determination of the voids content of dry compacted filler
- Part 5 Determination of the water content by oven drying
- Part 6 Determination of bulk density and water absorption
- Part 7 Determination of the bulk density of filler - pycnometer method
- Part 8 Determination of the polishing value
- Part 9 Determination of the resistance to wear by studded tires - Nordic test
- Part 10 Determination of the water suction height
DIN EN 1101 Textiles - Burning behavior of curtains and drapes - Detailed method for determining the flammability of vertically arranged samples (small flame)
DIN EN 1102 Textiles - Burning behavior of curtains and drapes - Detailed method for determining the flame spread properties of vertically arranged samples
DIN EN 1103 Textiles - Clothing textiles - Detailed procedure for determining the burning behavior
DIN EN 1104 Paper and cardboard intended for contact with food - Determination of the transfer of antimicrobial components
DIN EN 1106 Manually operated setting devices for gas devices
DIN EN 1107 waterproofing membranes - determination of dimensional accuracy
- Part 1 bitumen sheeting for roof waterproofing
- Part 2 plastic and elastomer sheets for roof waterproofing
DIN EN 1108 Waterproofing membranes - Bitumen membranes for roof waterproofing - Determination of dimensional stability in the event of cyclical temperature changes
DIN EN 1109 waterproofing membranes - Bitumen sheets for roof waterproofing - Determination of the cold bending behavior
DIN EN 1110 Waterproofing membranes - Bitumen membranes for roof waterproofing - Determination of the thermal stability at elevated temperatures
DIN EN 1111 Sanitary fittings - Thermostatic mixer (PN 10) - General technical specification
DIN EN 1112 Sanitary fittings - Showers for sanitary fittings for water supply systems of type 1 and type 2 - General technical specification
DIN EN 1113 Sanitary fittings - Shower hoses for sanitary fittings for water supply systems of type 1 and type 2 - General technical specification
DIN EN 1114 Plastics and rubber machines - Extruders and extrusion systems
- Part 1 safety requirements for extruders
- Part 3 safety requirements for fume cupboards
DIN EN 1116 kitchen furniture - coordination dimensions for kitchen furniture and kitchen appliances
DIN EN 1117 heat exchangers - liquid-cooled refrigerant condensers - test methods for determining performance
DIN EN 1118 heat exchangers - refrigerant-cooled liquid chillers - test methods for determining performance
DIN EN 1119 Plastics piping systems - Connections for pipes and fittings made of glass fiber reinforced thermosetting plastics (GRP) - Test method for tightness and resistance to damage of non-pressure-resistant flexible connections with elastomeric sealing elements
DIN EN 1120 Plastic piping systems - Pipes and fittings made of glass fiber reinforced thermosetting plastics (GRP) - Determination of the resistance to the effects of chemicals on the inside of a section in the deformed state
DIN EN 1121 doors - behavior between two different climates - test method
DIN EN 1122 Plastics - Determination of cadmium - wet digestion method
DIN EN 1123 Pipes and fittings made of longitudinally welded, hot-dip galvanized steel pipe with plug-in socket for sewer pipes
- Part 1 requirements, tests, quality control
- Part 2 dimensions
- Part 3 Dimensions and special requirements for negative pressure drainage systems and for drainage systems in shipbuilding
DIN EN 1124 Pipes and fittings made of longitudinally welded, stainless steel pipe with plug-in socket for sewer pipes
- Part 1 requirements, tests, quality control
- Part 2 System S - dimensions
- Part 3 System X - Dimensions
- Part 4 components for negative pressure drainage systems and drainage systems on ships
DIN EN 1125 locks and building hardware, panic door locks with horizontal operating rod for doors in escape routes, requirements and test methods
DIN EN 1127 Explosive atmospheres - explosion protection
- Part 1 basics and methodology
- Part 2 Basics and methodology in mines
DIN EN 1128 Cement-bonded chipboard - Determination of impact resistance with a hard body
DIN EN 1129 Furniture - Folding beds - Safety requirements and test methods
- Part 1 Safety requirements
- Part 2 test method
DIN EN 1130 furniture - cribs and cradles for the living area
- Part 1 Safety requirements
- Part 2 test method
DIN EN 1131 Fruit and vegetable juices - Determination of the relative density
DIN EN 1132 Fruit and vegetable juices - Determination of the pH value
DIN EN 1133 Fruit and vegetable juices - Determination of the formula number
DIN EN 1134 Fruit and vegetable juices - Determination of sodium, potassium, calcium and magnesium content; Atomic absorption spectrometric method (AAS)
DIN EN 1135 Fruit and vegetable juices - Determination of the ash content
DIN EN 1136 Fruit and vegetable juices - Determination of the phosphorus content; Spectrophotometric method
DIN EN 1137 Fruit and vegetable juices - Enzymatic determination of the citric acid (citrate) content; Spectrophotometric determination of NADH
DIN EN 1138 Fruit and vegetable juices - Enzymatic determination of the content of L-malic acid (L-malate); Spectrophotometric determination of NADH
DIN EN 1139 Fruit and vegetable juices - Enzymatic determination of the content of D-isocitric acid; Spectrophotometric determination of NADPH
DIN EN 1140 Fruit and vegetable juices - Enzymatic determination of the content of D-glucose and D-fructose; Spectrophotometric determination of NADPH
DIN EN 1141 Fruit and vegetable juices - Spectrophotometric determination of the prolin content
DIN EN 1142 Fruit and vegetable juices - Determination of the sulphate content
DIN EN 1143 Secure storage units - Requirements, classification and methods for testing resistance to burglary
- Part 1 safes, safes for ATMs, strongroom doors and strongrooms
- Part 2 deposit systems
DIN EN 1146 Respiratory protective equipment - Container equipment with compressed air with hood for self-rescue - Requirements, testing, marking
DIN EN 1147 Portable ladders for use by the fire brigade
DIN EN 1148 heat exchangers - Water / water heat exchangers for district heating - Test methods for determining the performance data
DIN EN 1149 protective clothing - electrostatic properties
- Part 1 test method for the measurement of the surface resistance
- Part 2 test method for the measurement of the electrical resistance through a material (volume resistance)
- Part 3 test method for the measurement of the charge reduction
- Part 5 performance requirements for material and construction requirements
DIN EN 1150 Protective clothing - Warning clothing for non-professional use - Test methods and requirements
DIN EN 1151 Pumps - Centrifugal pumps - Circulation pumps with electrical power consumption up to 200 W for heating systems and domestic water heating systems for domestic use
- Part 2 Noise test specification (vibro-acoustic) for the measurement of structure-borne noise and liquid-borne noise
DIN EN 1154 Locks and building hardware - Door locking devices with a controlled locking process - Requirements and test methods
DIN EN 1155 Locks and building hardware - Electrically operated hold-open devices for swing doors - Requirements and test methods
DIN EN 1158 locks and building hardware - door co-ordinators - requirements and test methods
DIN EN 1159 high-performance ceramics - ceramic composite materials - thermophysical properties
- Part 1 Determination of thermal expansion
- Part 2 Determination of the thermal diffusivity
- Part 3 Determination of the specific heat capacity
DIN EN 1160 Plants and equipment for liquefied natural gas - General properties of liquefied natural gas
DIN EN 1161 Feathers and down - Test method - Determination of moisture content
DIN EN 1162 Feathers and down - Test method - Determination of the oxygen number
DIN EN 1163 Feathers and down - Test method - Determination of the oil and fat content
DIN EN 1164 Feathers and down - Test method - Determination of the turbidity of an aqueous extract
DIN EN 1165 Feathers and down - Test methods - Determination of water-soluble chlorides
DIN EN 1167 Feathers and down - Test method for measuring the size of duvets filled with feathers and / or down
DIN EN 1168 precast concrete elements - hollow slabs
DIN EN 1169 Prefabricated concrete products - General rules for in-house production control of glass fiber reinforced concrete
DIN EN 1170 Prefabricated concrete products - Test method for glass fiber concrete
- Part 1 Determination of the consistency of the matrix; Setting attempt
- Part 2 Determination of the fiber content in fresh GFB; Washout process
- Part 3 Determination of the fiber content in fresh GFB during the spraying process
- Part 4 Determination of the flexural strength; Simple flexural tensile test
- Part 5 Determination of the flexural strength; Complete flexural tensile test
- Part 6 Determination of water absorption by means of immersion method and dry bulk density
- Part 7 Determination of the moisture-dependent changes in length
- Part 8 Testing of durability in the climatic cycle test
DIN EN 1171 Industrial valves - Cast iron gate valves
DIN EN 1172 Copper and copper alloys - Sheets and strips for the building industry
DIN EN 1173 copper and copper alloys - condition designations
DIN EN 1175; VDE 0117 Safety of industrial trucks - electrical requirements
- Part 1 General requirements for industrial trucks with battery-electric drive
- Part 2 General requirements for industrial trucks with internal combustion engines
- Part 3 Special requirements for electrical power transmission systems of industrial trucks with internal combustion engines
DIN EN 1176 playground equipment and playground floors
- Part 1 General safety requirements and test methods
- Part 2 Additional special safety requirements and test methods for swings
- Part 3 Additional special safety requirements and test methods for slides
- Part 4 Additional special safety requirements and test methods for cable cars
- Part 5 Additional special safety requirements and test methods for carousels
- Part 6 Additional special safety requirements and test methods for rocking devices
- Part 7 Instructions for installation, inspection, maintenance and operation
- Part 10 Additional special safety requirements and test methods for completely enclosed playground equipment
- Part 11 Additional special safety requirements and test methods for space nets
DIN EN 1177 Shock-absorbing playground floors - Determination of the critical fall height
DIN EN 1179 zinc and zinc alloys - primary zinc
DIN EN 1183 Materials and objects in contact with food - Test methods for temperature shock and resistance to temperature changes
DIN EN 1184 Materials and objects in contact with food - Test methods for the transparency of ceramic objects
DIN EN 1185 Starches and starch derivatives - Determination of the sulfur dioxide content - Acidimetric method
DIN EN 1186 Materials and objects in contact with food - plastics
- Part 1 Guide to the selection of test conditions and test methods for overall migration
- Part 2 Test method for total migration in olive oil by total immersion
- Part 3 test method for the overall migration in aqueous test food by complete immersion
- Part 4 test method for overall migration in olive oil by means of cells
- Part 5 test method for the overall migration into aqueous test food by means of cells
- Part 6 test method for overall migration in olive oil using a bag
- Part 7 test method for the overall migration into aqueous test food using a bag
- Part 8 test method for overall migration in olive oil with filling of the object
- Part 9 test method for the overall migration into aqueous test foodstuffs by filling the object
- Part 10 test method for overall migration in olive oil (modified method for use in the event of incomplete extraction of olive oil)
- Part 11 test method for the overall migration in mixtures of ¹⁴ C-labeled synthetic triglycerides
- Part 12 test methods for the overall migration at low temperatures
- Part 13 test methods for overall migration at high temperatures
- Part 14 test method for "substitute tests" for the overall migration from plastics, which are intended for contact with fatty foods, using the test media iso-octane and 95% ethanol
- Part 15 Alternative test methods for the determination of migration into fatty test food by rapid extraction in iso-octane and / or 95% ethanol
DIN EN 1191 Windows and doors - Endurance test - Test method
DIN EN 1192 doors - Classification of the strength requirements
DIN EN 1194 Timber structures - Glulam - Strength classes and determination of characteristic values
DIN EN 1195 timber structures - test methods - load-bearing behavior of load-bearing floor coverings
DIN EN 1196 Gas-fired warm air heaters for domestic and non-domestic use - Additional requirements for condensing warm air heaters
DIN EN 1197 Products for the treatment of water for human consumption - monozinc phosphate solution
DIN EN 1198 Products for the treatment of water for human consumption - monosodium dihydrogen phosphate
DIN EN 1199 Products for the treatment of water for human consumption - disodium monohydrogen phosphate
DIN EN 1200 products for the treatment of water for human consumption - trisodium phosphate
DIN EN 1244 Adhesives - Determination of the color and / or color change of adhesive spreads under the influence of light
DIN EN 1270 Playground equipment - Basketball equipment - Functional and safety requirements, test methods
DIN EN 1315 dimension sorting
- Part 1: hardwood logs
- Part 2: softwood logs
DIN EN 1316 Hardwood log quality sorting
- Part 2 poplar
DIN EN 1335 office furniture - office work chair
- Part 1 dimensions, determination of dimensions
- Part 2 security requirements
- Part 3 security checks
DIN EN 1337 bearings in construction
- Part 4 roller bearings
DIN EN 1338 Concrete paving stones - Requirements and test methods
DIN EN 1340 concrete curbs - requirements and test methods
DIN EN 1341 Natural stone slabs for outdoor areas - Requirements
DIN EN 1342 natural stone paving stones for outdoor areas - requirements and test methods
DIN EN 1343 Natural stone curbs for outdoor areas - Requirements and test methods
DIN EN 1348 Mortars and adhesives for tiles and slabs - Determination of the adhesive strength of cement-containing mortars for inside and outside
DIN EN 1400 Articles for infants and young children - Pacifiers for infants and young children - Safety requirements and test methods
DIN EN 1504 Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality monitoring and assessment of conformity
- Part 1 definitions
- Part 2 surface protection systems for concrete
- Part 3 Statically and non-statically relevant repairs
- Part 4 glue for building purposes
- Part 5 Injection of concrete components
- Part 6 anchoring of reinforcing bars
- Part 7 Corrosion protection of the reinforcement
- Part 8 quality control and assessment and verification of constancy of performance (AVCP)
- Part 9 General principles for the application of products and systems
- Part 10 Use of materials and systems on the construction site
DIN EN 1505 Ventilation of buildings - Air ducts and fittings made of sheet metal with rectangular cross-section - Dimensions
DIN EN 1506 Ventilation of buildings - Air ducts and fittings made of sheet metal with a round cross-section - Dimensions
DIN EN 1507 Ventilation of buildings - Rectangular sheet metal ducts - Requirements for strength and tightness
DIN EN 1530 door leaves - general and local evenness - tolerance classes
DIN EN 1533 Wooden floors - Determination of flexural strength under static load - Test methods
DIN EN 1534 wooden floors - determination of the indentation resistance - test method
DIN EN 1536 Execution of works in special foundation engineering - bored piles
DIN EN 1537 Execution of works in special foundation engineering - ground anchors
DIN EN 1538 Execution of works in special civil engineering - diaphragm walls
DIN EN 1562 malleable cast iron
DIN EN 1610 Laying and testing of sewer pipes and sewers
DIN EN 1627 Windows, doors closures - Burglar resistance - Requirements and classification
DIN EN 1643 valve monitoring systems for automatic shut-off valves for gas burners and gas appliances
DIN EN 1717 Protection of drinking water against contamination in drinking water installations and general requirements for safety devices
DIN EN 1777 aerial rescue vehicles for fire and rescue services , aerial work platforms (HABn) - safety requirements and testing
DIN EN 1789 Medical vehicles and their equipment - Road ambulances
DIN EN 1822 HEPA filters (EPA, HEPA and ULPA)
- Part 1 Classification, performance testing, labeling
- Part 2 aerosol generation, measuring devices, particle counting statistics
- Part 3 Checking the flat filter medium
- Part 4 leak test of the filter element (scanning method)
- Part 5 degree of separation test of the filter element
DIN EN 1837 Safety of machines - Machine-integrated lighting
DIN EN 1838 Applied lighting technology - emergency lighting
DIN EN 1839 Determination of the explosion limits of gases and vapors
DIN EN 1841 Adhesives - Test method for adhesives for floor and wall coverings - Determination of the dimensional change of a linoleum floor covering in contact with an adhesive
DIN EN 1846 fire fighting vehicles with turntable ladder or aerial work platform (aerial rescue vehicles )

DIN EN 1854 pressure switch for gas burners and gas appliances

DIN EN 1860 appliances, solid fuels and lighters for grilling

Part 1 grills for solid fuel; Requirements and test methods
Part 2 Grill charcoal and grill charcoal briquettes - Requirements and test methods
Part 3 ignition aids for barbecue charcoal and barbecue charcoal briquettes; Requirements and test methods
Part 4 grills for single use (disposable grills) when using solid fuels, requirements and test methods

DIN EN 1925 Determination of the water absorption coefficient due to capillary action

DIN EN 1926 Determination of compressive strength

DIN EN 1974 Food processing machines - Slicing machines - Safety and hygiene requirements

DIN EN 1990 ( Eurocode 0) Basics of structural engineering

DIN EN 1991 (Eurocode 1) Actions on structures

Part 1 General Effects
- Part 1-1 Weights, dead weight and payloads in building construction
- Part 1-2 Fire effects on structures
- Part 1-3 snow loads
- Part 1-4 wind loads
- Part 1-5 temperature effects
- Part 1-6 actions during construction
- Part 1-7 Extraordinary Effects
Part 2 traffic loads on bridges
Part 3 Effects as a result of cranes and machines
Part 4 Effects on silos and liquid containers

DIN EN 1992 (Eurocode 2) Dimensioning and construction of reinforced concrete and prestressed concrete structures

Part 1 General rules
- Part 1-1 General design rules and rules for building construction
- Part 1-2 structural design in case of fire
Part 2 concrete bridges - design and construction rules
Part 3 Silos and container structures made of concrete

DIN EN 1993 (Eurocode 3) Dimensioning and construction of steel structures

Part 1 General rules
- Part 1-1 General design rules and rules for building construction
- Part 1-2 structural design in case of fire
- Part 1-3 Supplementary rules for cold-formed thin-walled components and sheets
- Part 1-4 Supplementary rules for the use of stainless steels
- Part 1-5 Plate-shaped components
- Part 1-6 strength and stability of shells
- Part 1-7 Plate-shaped components with transverse loading
- Part 1-8 dimensioning of connections
- Part 1-9 Fatigue
- Part 1-10 Steel grade selection with regard to fracture toughness and properties in the thickness direction
- Part 1-11 dimensioning and construction of structures with tension members made of steel
- Part 1-12 Additional rules for the extension of EN 1993 to steel grades up to S700
Part 2 steel bridges
Part 3 towers, masts and chimneys
- Part 3-1 towers and masts
- Part 3-2 chimneys
Part 4 silos, tank structures and pipelines
- Part 4-1 silos
- Part 4-2 tank structures
- Part 4-3 pipelines
Part 5 piles and sheet piling
Part 6 crane tracks

DIN EN 1994 (Eurocode 4) Dimensioning and construction of composite structures made of steel and concrete

Part 1 General rules
- Part 1-1 General design rules and application rules for building construction
- Part 1-2 structural design in case of fire
Part 2 General design rules and application rules for bridges

DIN EN 1995 (Eurocode 5) Dimensioning and construction of wooden structures

Part 1 General rules
- Part 1-1 General rules and rules for building construction
- Part 1-2 structural design in case of fire
Part 2 bridges

DIN EN 1996 (Eurocode 6) Dimensioning and construction of masonry structures

Part 1 General rules
- Part 1-1 General rules for reinforced and unreinforced masonry
- Part 1-2 structural design in case of fire
Part 2 Planning, selection of building materials and execution of masonry
Part 3 Simplified calculation methods for unreinforced masonry structures

DIN EN 1997 (Eurocode 7) Calculation and dimensioning in geotechnical engineering

Part 1 General rules
Part 2 exploration and investigation of the subsoil

DIN EN 1998 (Eurocode 8) Design of structures against earthquakes

Part 1 Basics, earthquake effects and rules for buildings
Part 2 bridges
Part 3 Assessment and upgrading of buildings
Part 4 silos, tank structures and pipelines
Part 5 Foundations, retaining structures and geotechnical aspects
Part 7 is still missing
Part 6 towers, masts and chimneys
Part 1 General rules

DIN EN 1999 (Eurocode 9) Calculation and dimensioning of aluminum structures

Part 1 General rules
- Part 1-1 General design rules
- Part 1-2 structural design in case of fire
- Part 1-3 fatigue-loaded structures
- Part 1-4 Cold-formed profiled sheets
- Part 1-5 shell structures
Part 2 Structures susceptible to fatigue

DIN EN 2000-9999

DIN EN 2367 aerospace; Split pins made of steel EN 2573
DIN EN 3475 Aerospace - Electrical cables for aviation, use - Test method
- Part 100 general
- Part 201 visual inspection
- Part 202 mass
- Part 203 dimensions
- Part 301 conductor resistance
- Part 302 dielectric strength
- Part 303 insulation resistance
- Part 304 surface resistance
- Part 305 overload capacity
- Part 306 continuity of the leader
- Part 307 corona dropout voltage
- Part 401 Accelerated Aging
- Part 402 Shrinkage and Exfoliation
- Part 403 blocking and peeling
- Part 404 thermal shock
- Part 405 bending at room temperature
- Part 406 Wrap in the cold
- Part 407 Flammability
- Part 408 fire resistance
- Part 409 aging in a closed, airtight room
- Part 410 thermal service life
- Part 411 resistance to liquids
- Part 413 winding test
- Part 414 DSC procedure
- Part 415 Rapid temperature change
- Part 416 Thermal Resistance
- Part 418 thermal service life for conductors
- Part 501 notch strength
- Part 502 tear strength
- Part 503 abrasion resistance
- Part 504 torsion
- Part 505 tensile strength of the individual wires and conductor cables
- Part 506 Uniformity of the coating
- Part 507 Adhesion of the coating
- Part 508 layer thickness of the coating
- Part 509 solderability
- Part 510 tensile strength and elongation at break of extruded insulation, protective sleeves and jackets
- Part 511 abrasion line against line
- Part 512 alternating flexural strength
- Part 513 resistance to deformation
- Part 601 smoke density
- Part 602 toxicity
- Part 603 arc resistance, wet
- Part 604 Arc Resistance, Dry
- Part 605 behavior after short circuit, damp
- Part 701 Strippability and adhesive strength of the insulation on the conductor
- Part 702 retractability of the braid
- Part 703 durability of the manufacturer identification
- Part 704 flexibility
- Part 705 contrast measurement
- Part 706 UV laser marking
- Part 801 operating capacity
- Part 802 capacity difference
- Part 803 capacity deviation
- Part 804 velocity of propagation
- Part 805 wave resistance
- Part 806 damping
- Part 807 coupling resistance
- Part 808 crosstalk
DIN EN 3476 Aerospace - Steel FE-PL1501 (30CrMo12) - Air melted - Soft annealed - Forged raw material - a or D = 300 mm
DIN EN 3479 aerospace - steel FE-PM1802 (X5CrNiCu15-5) - remelted with consumable electrode - solution annealed and hardened - plates - 6 mm <a = 20 mm - 1070 MPa = Rm = 1220 MPa
DIN EN 3480 Aerospace - Steel FE-PA3601 (X6CrNiTi18-10) - Air melt - Soft annealed - Plates - 6 mm <a = 50 mm - 500 MPa = Rm = 700 MPa
DIN EN 4108 Aerospace - Ring spanner sockets, open, toothed with internal square
DIN EN 4219 Aerospace - Hexagon cap nuts, self-locking with plastic hood with normal wrench size made of corrosion-resistant steel
DIN EN 9101 Quality Management Systems - Audit Requirements for Aviation, Space and Defense Organizations
DIN EN 9104 Aerospace - Quality management systems
- Part 1 Requirements for certification procedures for quality management systems in aviation, space travel and defense
- Part 2 Requirements for monitoring / control of certification procedures for quality management systems in the aerospace industry
DIN EN 9200 Aerospace - Program Management - Guideline for a Project Management Specification,

DIN EN 10000–19999

DIN EN 10001 Definition and classification of pig iron

DIN EN 10002 tensile test for metallic materials, December 2009 replaced by DIN EN ISO 6892

DIN EN 10021 General technical delivery conditions for steel products

DIN EN 10024 I-profiles with inclined inner flange surfaces

DIN EN 10025 Hot-rolled products made of structural steels

Part 1 General technical delivery conditions
Part 2 Technical delivery conditions for unalloyed structural steels
Part 3 Technical delivery conditions for normalized / normalized rolled, weldable fine-grain structural steels
Part 4 Technical delivery conditions for thermomechanically rolled, weldable fine-grain structural steels
Part 5 Technical delivery conditions for weatherproof structural steels
Part 6 Technical delivery conditions for flat products made of steels with a higher yield point in the quenched and tempered condition

DIN EN 10027 designation systems for steels

Part 1 short names
Part 2 number system

DIN EN 10029 Hot-rolled sheet steel 3 mm thick; Limiting dimensions, shape tolerances

DIN EN 10045 Metallic materials; Charpy notched bar impact test.

DIN EN 10055 Hot-rolled isosceles T-steel with rounded edges and transitions

DIN EN 10056 Equal and unequal angles made of steel

Part 1 dimensions
Part 2 dimensional limits and form tolerances

DIN EN 10058 Hot-rolled flat steel bars for general use - dimensions, shape tolerances and tolerances

DIN EN 10059 Hot-rolled square steel bars for general use - dimensions, shape tolerances and tolerances

DIN EN 10060 Hot-rolled steel rods - dimensions, shape tolerances and dimensional limits

DIN EN 10061 Hot-rolled hexagonal steel bars - dimensions, shape tolerances and dimensional limits

DIN EN 10079 Definitions for steel products

DIN EN 10083 quenched and tempered steels

Part 1 General technical delivery conditions
Part 2 Technical delivery conditions for unalloyed steels
Part 3 Technical delivery conditions for alloyed steels

DIN EN 10088 Stainless steels

Part 1 list of stainless steels
Part 2 Technical delivery conditions for sheet metal and strip made of corrosion-resistant steels for general use
Part 3 Technical delivery conditions for semi-finished products, rods, wire rod, drawn wire, profiles and bright steel products made of corrosion-resistant steels for general use
Part 4 Technical delivery conditions for sheet metal and strip made of corrosion-resistant steels for the building industry
Part 5 Technical delivery conditions for bars, wire rod, drawn wire, profiles and bright steel products made of corrosion-resistant steels for the building industry

DIN EN 10090 valve steels and alloys for internal combustion engines

DIN EN 10095 heat-resistant steels and nickel alloys

DIN EN 10106 Cold-rolled, non-grain-oriented electrical steel sheet and strip in the final annealed condition

DIN EN 10108 Round steel wire rod for cold-formed nuts and bolts

DIN EN 10111 Continuously hot-rolled strip and sheet made of soft steels for cold forming - Technical delivery conditions

DIN EN 10131 Cold-rolled flat products without coating and with an electrolytic zinc or zinc-nickel coating made of soft steels and steels with a higher yield point for cold forming - limit dimensions and shape tolerances

DIN EN 10142 Continuously hot-dip galvanized strip and sheet made of soft steels for cold forming - Technical delivery conditions, September 2004 replaced by DIN EN 10327

DIN EN 10143 Continuously hot-dip coated sheet metal and strip made of steel - limit dimensions and shape tolerances

DIN EN 10152 Electrolytically galvanized, cold-rolled flat products made of steel for cold forming - Technical delivery conditions

DIN EN 10162 cold sections made of steel - Technical delivery conditions - Limiting dimensions and shape tolerances

DIN EN 10163 delivery conditions for the surface quality of hot-rolled steel products (sheet metal, wide flat steel and profiles)

DIN EN 10169 Continuously organically coated (coil-coated) flat products made of steel

Part 1 General (definitions, materials, limit deviations, test methods)
Part 2 products for external building use
Part 3 products for indoor use

DIN EN 10204 Metallic products, types of test certificates

DIN EN 10218 steel wire and wire products

Part 1 test method
Part 2 wire dimensions and tolerances

DIN EN 10220 Seamless and welded steel pipes, general tables for dimensions and length-related mass

DIN EN 10226 pipe thread for connections sealing in the thread

Part 1 tapered external threads and cylindrical internal threads - dimensions, tolerances and designation
Part 2 tapered external threads and tapered internal threads - dimensions, tolerances and designation
Part 3 examination with limit gauges

DIN EN 10241 steel fittings with thread

DIN EN 10242 malleable cast iron fittings

DIN EN 10255 Pipes made of unalloyed steel, suitable for welding and thread cutting

DIN EN 10270 steel wire for springs

Part 1 Patented-drawn unalloyed spring steel wire
Part 2 Oil tempered spring steel wire
Part 3 Stainless spring steel wire

DIN EN 10278 Dimensions and tolerances of bright steel products

DIN EN 10279 Hot-rolled U-section steel - limit dimensions, form tolerances and limit deviations in mass

DIN EN 10283 Corrosion-resistant cast steel

DIN EN 10291 Metallic materials - Uniaxial creep test under tensile stress - Test method

DIN EN 10292 Continuously hot-dip coated strip and sheet made of steels with high yield strength for cold forming - Technical delivery conditions

DIN EN 10305 Precision steel tubes - Technical delivery conditions

Part 1 Seamless cold drawn tubes
Part 2 Welded cold drawn tubes
Part 3 Welded size-rolled tubes
Part 4 Seamless cold drawn tubes for hydraulic and pneumatic pressure lines
Part 5 Welded dimensionally formed tubes with square and rectangular cross-section
Part 6 Welded cold-drawn tubes for hydraulic and pneumatic pressure lines

DIN EN 10326 Continuously hot-dip coated strip and sheet made of structural steels - Technical delivery conditions

DIN EN 10327 Continuously hot-dip coated strip and sheet made of soft steels for cold forming - Technical delivery conditions

DIN EN 10336 Continuously hot-dip refined and electrolytically refined strip and sheet made of multiphase steels for cold forming, technical delivery conditions

DIN EN 12004 Mortars and adhesives for tiles and slabs - Requirements, conformity assessment, classification and designation

DIN EN 12056 gravity drainage systems within buildings

Part 1 General implementation requirements
Part 2 wastewater systems, planning and calculation
Part 3 roof drainage, planning and calculation
Part 4 wastewater lifting plants, planning and calculation
Part 5 Installation and testing, instructions for operation, maintenance and use

DIN EN 12057 Natural stone products - Tiles - Requirements

DIN EN 12058 Natural stone products - Floor slabs and step coverings - Requirements

DIN EN 12067 Gas-air compound control devices for gas burners and gas appliances

Part 1: Pneumatic version, June 2011 replaced by DIN EN 88-1
Part 2: Electronic execution

DIN EN 12077 Safety of Cranes - Health and Safety Requirements

Part 2: Limiting and display devices

DIN EN 12097 Ventilation of buildings - Air ducts - Requirements for duct components for the maintenance of duct systems

DIN EN 12193 Light and lighting - Sports facility lighting

DIN EN 12198 Safety of machines - Assessment and reduction of the risk of radiation emitted by machines

Part 1 General principles
Part 2 measurement method for radiation emission
Part 3 Reduction of radiation through attenuation or shielding

DIN EN 12208 Windows and doors - Watertightness - Classification

DIN EN 12220 Ventilation for buildings - Air ducts - Dimensions of round flanges for general ventilation purposes

DIN EN 12237 Ventilation of buildings - Air ducts - Strength and tightness of ducts with a round cross-section made of sheet metal

DIN EN 12266 Industrial valves - Testing of metal valves

Part 1 Pressure tests, test methods and acceptance criteria - Mandatory requirements
Part 2 tests, test procedures and acceptance criteria; Supplementary requirements

DIN EN 12373 Aluminum and aluminum alloys - anodizing

Part 1 Method for specifying decorative and protective anodically generated oxide layers on aluminum
Part 2 Determination of the mass per unit area (mass per unit area) of anodically generated oxide layers - Gravimetric method
Part 3 Determination of the thickness of anodically generated oxide layers; Non-destructive measurement with a light section microscope
Part 4 Assessment of the colorability of anodically generated oxide layers after compaction by means of a paint drop test with prior acid treatment
Part 5 Testing the quality of compacted, anodically produced oxide layers by determining the admittance value
Part 6 Testing of the quality of compacted, anodically produced oxide layers by determining the loss of mass after immersion in chromophosphoric acid solution without prior acid treatment
Part 7 Testing of the quality of compacted, anodically generated oxide layers by determining the loss of mass after immersion in a chromophosphoric acid solution with prior acid treatment
Part 8 Comparative determination of the resistance of colored, anodically produced oxide layers to ultraviolet light and heat
Part 9 Measurement of the abrasion resistance and the abrasion number of anodically generated oxide layers by abrasion testing with a grinding wheel tester
Part 10 Measurement of the mean specific abrasion resistance of anodically generated oxide layers by abrasion testing with an abrasive jet tester
Part 11 Measurement of the directed reflectance and the specular gloss of anodically generated oxide layers at angles of 20 °, 45 °, 60 ° or 85 °
Part 12 Measurement of the reflection properties of aluminum surfaces with the help of integrating spheres
Part 13 Measurement of the reflective properties of aluminum surfaces with simplified or precision goniophotometers
Part 14 Visual determination of the image sharpness of anodically generated oxide layers; Measuring grid method
Part 15 Testing of the resistance of anodically generated oxide layers to cracking when deformed
Part 16 Testing of the continuity of thin anodically generated oxide layers; Copper sulfate test
Part 17 Determination of the electrical breakdown voltage
Part 18 rating system for pitting corrosion; Benchmark method
Part 19 rating system for pitting corrosion; Grid counting method

DIN EN 12390 testing of hardened concrete

Part 1 shape, dimensions and other requirements for specimens and shapes
Part 2 Production and storage of test specimens for strength tests
Part 3 compressive strength of test specimens
Part 4 Determination of compressive strength; Requirements for testing machines
Part 5 flexural strength of test specimens
Part 6 tensile splitting strength of test specimens
Part 7 density of hardened concrete
Part 8 depth of water penetration under pressure
Part 9 Frost and frost-thawing salt resistance - weathering (pre-standard DIN CEN / TS 12390-9)

DIN EN 12407 test method for natural stone - petrographic test

DIN EN 12440 natural stone - criteria for the designation

DIN EN 12445 doors; Safety of use of power operated gates; Test procedure

DIN EN 12453 doors; Safety of use of power operated gates; conditions

DIN EN 12464 Light and lighting - Lighting of workplaces

Part 1 indoor workplaces
Part 2 outdoor workplaces

DIN EN 12469 Biotechnology - Performance criteria for microbiological safety workbenches

DIN EN 12566 small sewage treatment plants for up to 50 PE

Part 1 Factory-made septic tanks
Part 3 Prefabricated and / or on-site assembled systems for the treatment of domestic wastewater
Part 4 kits for septic tanks to be installed on site
Part 5 filtration systems for pretreated domestic wastewater (draft)
Part 6 Prefabricated systems for the further treatment of sewage draining from septic tanks (draft)
Part 7 Factory-made units for a third cleaning part (draft)

DIN EN 12568 Foot and leg protection - Requirements and test methods for penetration-resistant metal insoles and toe caps

DIN EN 12570 industrial valves - procedure for the design of the actuating element

DIN EN 12604 doors; Mechanical aspects; Requirements and test methods

DIN EN 12605 doors; Mechanical aspects; Test procedure, December 2017 replaced by DIN EN 12604

DIN EN 12627 Industrial fittings - Welding ends for fittings made of steel

DIN EN 12644 cranes - information for use and testing

Part 1 operating instructions
Part 2 marking

DIN EN 12663 Railway applications - Strength requirements for car bodies of rail vehicles

Part 1: Locomotives and passenger vehicles (and alternative procedures for freight wagons)
Part 2: freight wagons

DIN EN 12665 light and lighting, basic terms and criteria for specifying lighting requirements

DIN EN 12670 Terminology of natural stones - Petrographic names

DIN EN 12770 Shoes - Test method for outsoles - Abrasion resistance

DIN EN 12792 Ventilation for buildings - symbols, terminology and graphic symbols

DIN EN 12828 Safety equipment for heat generation systems

DIN EN 12831 heating load of buildings (heat demand calculation)

DIN EN 12845 Fixed fire fighting systems - Automatic sprinkler systems - Planning, installation and maintenance

DIN EN 12952 water tube boilers and system components

DIN EN 12975 Thermal solar systems and their components

DIN EN 12999 cranes - loading cranes

DIN EN 13000 cranes - mobile cranes

DIN EN 13001 cranes - general construction

Part 1 General principles and requirements
Part 2 load effects

DIN EN 13031 Greenhouses - Dimensioning and construction

Part 1 cultural greenhouses

DIN EN 13032 Light and lighting - Measurement and display of photometric data from lamps and luminaires

Part 1 measurement and data format
Part 1 Correction 1 Measurement and data format
Part 2 Presentation of the data for indoor and outdoor workplaces
Part 2 Correction 1 Presentation of data for indoor and outdoor workplaces
Part 3 Presentation of data for the emergency lighting of workplaces

DIN EN 13098 Workplace atmosphere - guidelines for the measurement of microorganisms and endotoxins in the air

DIN EN 13129 Railway applications - Air treatment in long-distance rail vehicles

Part 1 comfort parameters
Part 2 type tests

DIN EN 13135 cranes - equipment

Part 1 Cranes - Safety - Construction - Equipment requirements - Part 1: Electrotechnical equipment
Part 2 Cranes - Equipment - Part 2: Non-electrotechnical equipment

DIN EN 13155 cranes - Loose load suspension devices

DIN EN 13157 Cranes - Safety - Hand-operated cranes

DIN EN 13162 Thermal insulation materials for buildings - Factory-made mineral wool (MW) products

DIN EN 13163 Thermal insulation products for buildings - Factory-made products made of expanded polystyrene (EPS)

DIN EN 13164 Thermal insulation products for buildings - Factory-made products from extruded polystyrene foam (XPS)

DIN EN 13165 Thermal insulation materials for buildings - Factory-made products made of rigid polyurethane foam (PU)

DIN EN 13166 Thermal insulation materials for buildings - Factory-made products made of phenolic resin foam (PF)

DIN EN 13167 Thermal insulation materials for buildings - Factory-made foam glass (CG) products

DIN EN 13168 Thermal insulation products for buildings - Factory-made wood wool (WW) products

DIN EN 13169 Thermal insulation materials for buildings - Factory-made products made of expanded perlite (EPB)

DIN EN 13170 Thermal insulation materials for buildings - Factory-made products made of expanded cork (ICB)

DIN EN 13171 Thermal insulation materials for buildings - Factory-made products made from wood fibers (WF)

DIN EN 13172 thermal insulation materials - conformity assessment

DIN EN 13180 Ventilation of buildings - Air ducts - Dimensions and mechanical requirements for flexible air ducts

DIN EN 13201 street lighting

Part 1 Selection of the lighting classes
Part 2 quality characteristics
Part 3 Calculation of the quality characteristics
Part 3 Correction 1 Calculation of the quality characteristics
Part 4 Methods for measuring the quality characteristics of street lighting systems

DIN EN 13300 Coating materials - Water-based coating materials and coating systems for interior walls and ceilings

DIN EN 13306 terms of maintenance

DIN EN 13348 Copper and copper alloys - Seamless, round copper tubes for medical gases or vacuum

DIN EN 13373 Determination of geometric characteristics of rocks

DIN EN 13374 Temporary edge protection systems - Product specifications, test methods

DIN EN 13384 exhaust systems - thermal and fluidic calculation methods

DIN EN 13432 Packaging - Requirements for the recovery of packaging through composting and biodegradation - Test scheme and evaluation criteria for the classification of packaging; see. Biodegradable plastic , biodegradability

DIN EN 13494 Thermal insulation materials for the building industry - Determination of the tensile strength between adhesive, adhesive mortar and thermal insulation material and between the plaster and thermal insulation material

DIN EN 13496 Thermal insulation products for building applications - Determination of the mechanical properties of glass fiber fabrics

DIN EN 13497 Thermal insulation materials for the building industry - Determination of the impact resistance of external thermal insulation composite systems (ETICS)

DIN EN 13498 Thermal insulation materials for the building industry - Determination of the penetration resistance of external thermal insulation composite systems (ETICS)

DIN EN 13499 Thermal insulation materials for buildings - External thermal insulation composite systems (ETICS) made of expanded polystyrene - Specifications

DIN EN 13500 Thermal insulation materials for buildings - External thermal insulation composite systems (ETICS) made of mineral wool - Specifications

DIN EN 13501 Classification of building products and types of fire behavior

Part 1 Classification with the results from the tests on the fire behavior of building products
Part 2 Classification with the results from the fire resistance tests, with the exception of ventilation systems
Part 3 Classification with the results from the fire resistance tests on components of building services systems: Fire-resistant lines and fire dampers
Part 4 Classification with the results from the fire resistance tests of smoke control systems
Part 5 Classification with the results of tests of roofs exposed to external fire
Part 6 Classification with the results from the fire behavior tests of electrical cables

DIN EN 13523 Coil-coated metals - test method

Part 0 General introduction and list of test methods
Part 1 layer thickness
Part 2 shine
Part 3 color distance
Part 4 pencil hardness
Part 5 Resistance to rapid deformation (impact test)
Part 6 adhesive strength after indentation (cupping test)
Part 7 resistance to cracking when bending (T-bending test)
Part 8 Resistance to salt spray
Part 9 resistance to immersion in water
Part 10 Resistance to fluorescent UV radiation and condensation of water
Part 11 Resistance to solvents (rub test)
Part 12 resistance to scratches
Part 13 Resistance to accelerated aging due to the action of heat
Part 14 chalks (method according to helmets)
Part 15 metamerism
Part 16 Resistance to abrasion
Part 17 Adhesion strength of peelable films
Part 18 Resistance to staining
Part 19 sample plates and methods for outdoor exposure
Part 20 Adhesion strength of foam
Part 21 Evaluation of outdoor weathered sample panels
Part 22 color distance; Visual comparison
Part 23 Resistance of color in humid atmospheres containing sulfur dioxide
Part 24 Block and stack strength
Part 25 resistance to moisture
Part 26 Resistance to condensation water
Part 27 resistance to damp packaging (cataplasma test)
Part 29 resistance to pollution

DIN EN 13537 requirements for sleeping bags

DIN EN 13557 cranes - control elements and control stations

DIN EN 13586 cranes - access

DIN EN 13611 Safety and control devices for burners and fuel devices for gaseous and / or liquid fuels - General requirements

DIN EN 13706 specifications for pultruded profiles

Part 1 designation
Part 2 test methods and general requirements
Part 3 Special requirements

DIN EN 13725 Air quality - Determination of the odor concentration with dynamic olfactometry

DIN EN 13755 water absorption under atmospheric pressure

DIN EN 13779 Ventilation of non-residential buildings - General principles and requirements for ventilation and air conditioning systems and room cooling systems

DIN EN 13795 surgical clothing and drapes - requirements and test methods

Part 1 surgical drapes and gowns
Part 2 clean air clothing

DIN EN 13830 curtain walls - product standard

DIN EN 13852 cranes - offshore cranes

Part 1 Offshore cranes for general use
Part 2 floating cranes

DIN EN 13859 waterproofing membranes - Definitions and properties of underlay and sarking membranes

Part 1 underlay and sarking membranes for roof coverings
Part 2 underlay and sarking membranes for walls

DIN EN 13861 Safety of machines - Guidelines for the application of ergonomic standards in the design of machines

DIN EN 13914 Planning, preparation and execution of exterior and interior plasters

Part 1 exterior plasters
Part 2 interior plasters

DIN EN 14043 automatic turntable ladders (fire brigade)

DIN EN 14044 sequential turntable ladders / aerial work platforms (HAB)

DIN EN 14073 office furniture, office cabinets

Part 2 safety requirements
Part 3 test method for determining the stability and strength of the construction

DIN EN 14079 Non-active medical devices - Performance requirements and test methods for gauze made of cotton and gauze made of cotton and viscose

DIN EN 14126 protective clothing - Performance requirements and test methods for protective clothing against infectious agents

DIN EN 14142 Postal services

Part 1 Components of the postal address
Part 2 Country-specific templates

DIN EN 14153 Training of recreational
scuba divers
- Part 1 Supervised diver
- Part 2 Self-employed diver
- Part 3 diving group leader

DIN EN 14175 deductions

Part 1 terms
Part 2 requirements for safety and performance
Part 3 Type examination procedure
Part 4 on-site test procedure
Part 5 Recommendations for Installation and Maintenance (English Version)
Part 6 fume cupboards with variable airflow
Part 7 fume cupboards for high thermal and acid loads (smoke fume cupboards)

DIN EN 14214 Fuels for motor vehicles - Fatty acid methyl esters (FAME) for diesel engines - Requirements and test methods ( biodiesel )

DIN EN 14238 cranes - hand-held manipulators

DIN EN 14241 exhaust systems - Material requirements and tests for elastomer seals and sealing materials

DIN EN 14411 Ceramic tiles - Terms, classification, quality characteristics and labeling

DIN EN 14413 Recreational diving services - Safety-relevant minimum requirements for the training of diving instructors

Part 1 training level 1
Part 2 training level 2

DIN EN 14439 Cranes - Safety - Tower cranes

DIN EN 14467 Recreational diving services - Requirements for service providers of recreational scuba diving

DIN EN 14468 table tennis

Part 1 Table tennis, functional and safety requirements, test methods
Part 2 posts of net sets - Requirements and test methods

DIN EN 14470 fire-resistant storage cabinets

Part 1 safety cabinets for flammable liquids
Part 2 safety cabinets for pressurized gas cylinders

DIN EN 14492 Cranes - Power driven winches and hoists

Part 1 Power-driven winches
Part 2 Power-driven hoists

DIN EN 14502 Cranes - Equipment for lifting people

Part 1 Hanging access equipment
Part 2 Height-adjustable control stands

DIN EN 14530 Plastics - Free-flowing unsaturated polyester molding compounds (UP-PMC)

Part 1 Designation system and basis for specifications
Part 2 production of test specimens and determination of properties
Part 3 requirements for selected molding compounds

DIN EN 14583 Workplace atmosphere - Volumetric sampling devices for bioaerosols - Requirements and test methods

DIN EN 14597 temperature control devices and temperature limiters for heat generating systems

DIN EN 14604 smoke alarm device

DIN EN 14605 Protective clothing against liquid chemicals - Performance requirements for chemical protective suits with liquid-tight (type 3) or spray-tight (type 4) connections between the parts of the clothing, including items of clothing that only protect parts of the body (types PB [3] and PB [4])

DIN EN 14634 glass packaging - crown mouthpiece 26 H 180 - dimensions

DIN EN 14635 glass packaging - crown mouthpiece 26 H 126 - dimensions

DIN EN 14683 Medical face masks - Requirements and test methods

DIN EN 14719 Fiber, paper and cardboard - Determination of the diisopropylnaphthalene (DIPN) content by means of solvent extraction

DIN EN 14750 Railway applications - Air treatment in rail vehicles for inner-city and regional local transport

Part 1 comfort parameters
Part 2 type tests

DIN EN 14798 Glass packaging - Manual crown cork opener - Dimensions

DIN EN 14877 plastic surfaces on outdoor sports facilities - requirements

DIN EN 14887 Glass packaging - Corkscrews - General requirements

DIN EN 14985 cranes - jib slewing cranes

DIN EN 15038 Translation Services - Service Requirements

DIN EN 15051 Exposure at the workplace - Measurement of the dustiness of bulk solids

Part 1 Requirements and selection of test methods
Part 2 method with rotating drum
Part 3 method with continuous fall

DIN EN 15052 Resilient, textile floor coverings and laminate floors - Assessment and requirements for emissions of volatile organic compounds (VOC) (currently draft)

DIN EN 15056 cranes - Requirements for spreaders for handling containers

DIN EN 15085 welding technology in rail vehicle construction

DIN EN 15090 shoes for the fire brigade

DIN EN 15193 Energy assessment of buildings - Energy requirements for lighting

DIN EN 15227 Railway applications - Requirements for the collision safety of rail vehicle bodies

DIN EN 15241 Ventilation of buildings - Calculation method for the energy loss due to ventilation and infiltration in buildings

DIN EN 15242 Ventilation of buildings - Calculation method for determining the air volume flow in buildings including infiltration

DIN EN 15251 input parameters for the indoor climate for the design and evaluation of the energy efficiency of buildings - indoor air quality, temperature, light and acoustics

DIN EN 15330 Sports floors - Synthetic turf surfaces and needle felts mainly produced for outdoor use

DIN EN 15376 Fuels for motor vehicles - Ethanol for use as a blend component in petrol - Requirements and test methods

DIN EN 15423 Ventilation of buildings - Fire protection of ventilation systems in buildings

DIN EN 15543 Glass packaging - Bottle closures - Screw mouthpieces for bottles for non-carbonated liquids

DIN EN 15635 Fixed steel shelving systems - Use and maintenance of storage facilities

DIN EN 15800 Cylindrical coil springs made of round wires - Quality specifications for cold-formed compression springs

DIN EN 15883 washer-disinfectors

Part 1 General requirements, terms and test methods
Part 2 Requirements and test methods for washer-disinfectors with thermal disinfection for surgical instruments, anesthesia machines, vessels, utensils, glass appliances, etc.
Part 3 Requirements and test methods for washer-disinfectors with thermal disinfection for containers for human waste
Part 4 Requirements and test methods for washer-disinfectors with chemical disinfection for thermolabile endoscopes
Part 5 Test soiling and test methods to demonstrate the cleaning effect (ISO / TS 15883-5: 2005); German version CEN ISO / TS 15883-5: 2005
Part 6 Requirements and test methods for washer-disinfectors with thermal disinfection for non-invasive, non-critical medical devices and accessories in the healthcare sector

DIN EN 15892 Railway applications - Noise emission - Noise measurement in the driver's cab

DIN EN 16001 energy management systems - requirements with instructions for use

DIN EN 16063 Packaging - Plastic containers - Designation of plastic closure mouthpieces

DIN EN 16064 Packaging - Plastic containers - PET mouthpiece 30/25 H (18.5)

DIN EN 16065 Packaging - Plastic containers - PET mouthpiece 30/25 L (16.8)

DIN EN 16066 packaging - plastic containers - PET mouthpiece 26.7 (thread pitch 6.35)

DIN EN 16067 Packaging - Plastic containers - PET mouthpiece 26.7 (thread pitch 9.00)

DIN EN 16068 Packaging - plastic containers - PET mouthpiece 38

DIN EN 16094 Laminate Flooring - Test method for determining the microscratch resistance (draft)

DIN EN 16287 Glass packaging - Screw mouthpieces for bottles with internal pressure - MCA 1 mouthpiece

DIN EN 16288 Glass packaging - Screw mouthpieces for bottles with internal pressure - MCA 3 mouthpiece

DIN EN 16289 Glass packaging - Screw mouthpieces for bottles with internal pressure - MCA 7.5 RF mouthpiece

DIN EN 16290 Glass packaging - Screw mouthpieces for bottles with internal pressure - MCA 7.5 R mouthpiece

DIN EN 16291 Glass packaging - Screw mouthpieces for bottles with internal pressure

Part 1 reusable MCA 2 mouthpiece
Part 2 disposable MCA 2 mouthpiece

DIN EN 16292 Glass packaging - Screw mouthpieces - Flattened threads

DIN EN 16293 Packaging - Packaging made of glass - Deep BVS mouthpieces for still wines

DIN EN 16341 Selection of standards and other standard-type documents for defense technology products and services - priority

DIN EN 16352 Logistics - Specifications for reporting criminal offenses

DIN EN 16776 Resilient floor coverings - Heterogeneous polyurethane floor coverings - Specification

DIN EN 20000-59999

DIN EN 22553 Symbolic representation of welding and soldering seams
DIN EN 27888 water quality; Determination of electrical conductivity
DIN EN 28601 date formats, September 2006 replaced by DIN ISO 8601
DIN EN 28676 hexagon bolts with thread up to the head; Fine thread M 8 × 1 to M 52 × 3 (product classes A and B), March 2001 replaced by DIN EN ISO 8676
DIN EN 29692 weld preparation
DIN EN 45020 standardization and related activities - general terms (ISO / IEC Guide 2: 2004)
DIN EN 50005 Industrial low-voltage switchgear; Terminal designations and codes, general rules
DIN EN 50020 Electrical equipment for potentially explosive areas - intrinsic safety "i"; August 2007 replaced by DIN EN 60079-11
DIN EN 50090 Electrical system technology for homes and buildings (ESHG)
- Part 2 system overview
  - Part 2-1 architecture
  - Part 2-2 (VDE 0829-2-2) General technical requirements
  - Part 2-3 (VDE 0829-2-3) Requirements for functional safety for products that are intended for installation in ESHG
- Part 3 application aspects
  - Part 3-1 Introduction to the application structure
  - Part 3-2 application process ESHG class 1
  - Part 3-3 ESHG interworking model and common ESHG data formats
- Part 4 Media-independent layer
  - Part 4-1 application layer for ESHG class 1
  - Part 4-2 transport layer, network layer and general parts of the data link layer for ESHG class 1
  - Part 4-3 Communication via IP (EN 13321-2)
- Part 5 Media and media-dependent layers
  - Part 5-1 signal transmission on electrical low-voltage networks for ESHG class 1
  - Part 5-2 network based on ESHG class 1, two-wire cables (twisted pair)
  - Part 5-3 Signal transmission via radio
- Part 7-1 System Management - Management Procedures
- Part 8 Conformity assessment of products
- Part 9-1 Installation requirements - cabling of two-wire lines ESHG class 1
DIN EN 50102 (DIN EN 62262, VDE 0470-100) Degrees of protection through housings for electrical equipment (equipment) against external mechanical loads (IK code)
DIN EN 50107 fluorescent tube devices and fluorescent tube systems with an open circuit voltage above 1 kV, but not above 10 kV
- Part 1 General Requirements
- Part 2 Requirements for earth fault protection devices and no-load protection devices
DIN EN 50110 (VDE 0105) Operation of electrical systems
- Part 1 (VDE 0105-1)
- Part 2 (VDE 0105-2) (national appendices)
DIN EN 50117 coaxial cable
- Part 1 (VDE 0887-1) basic specification
- Part 2 framework specification for cables for cable distribution systems
  - Part 2-1 (VDE 0887-2-1) House installation cables in the range from 5 MHz - 1000 MHz
  - Part 2-2 (VDE 0887-2-2) outdoor cable in the range from 5 MHz - 1000 MHz
  - Part 2-3 (VDE 0887-2-3) Distributors and line cables for systems in the range of 5 MHz - 1000 MHz
  - Part 2-4 (VDE 0887-2-4) House installation cable in the range from 5 MHz - 3000 MHz
  - Part 2-5 (VDE 0887-2-5) outdoor cable in the range from 5 MHz - 3000 MHz
- Part 3 (VDE 0887-3) Framework specification for house connection cables
  - Part 3-1 (VDE 0887-3-1) Framework specification for cables for applications in telecommunications; Miniature cables for digital communication systems
- Part 4 (VDE 0887-4) Framework specification for distribution and line cables
- Part 4-1 (VDE 0887-4-1) Framework specification for cables RuK cabling according to EN 50173 - house installation cables in the range from 5 MHz to 3000 MHz
- Part 5 (VDE 0887-5) Framework specification for house installation cables for systems for frequencies from 5 MHz to 2150 MHz
- Part 6 (VDE 0887-6) Framework specification for house connection cables for systems for frequencies from 5 MHz to 2150 MHz
DIN EN 50121 Railway applications - Electromagnetic compatibility
- Part 1 (VDE 0115-121-1) General
- Part 2 (VDE 0115-121-2) Emitted interference from the entire railway system to the outside world
- Part 3-1 (VDE 0115-121-3-1) Railway vehicles - train and entire vehicle
- Part 3-2 (VDE 0115-121-3-2) Railway vehicles - devices
- Part 4 (VDE 0115-121-4) Emitted interference and interference immunity of signal and telecommunications equipment
DIN EN 50125 Railway applications - Environmental conditions for equipment
- Part 1 (VDE 0115-108-1) equipment on rail vehicles
- Part 2 (VDE 0115-108-2) Fixed electrical systems
- Part 3 (VDE 0115-108-3) Environmental conditions for signal and telecommunication equipment
DIN EN 50126 Railway applications - Specification and proof of reliability, availability, maintainability and safety (RAMS)
- Part 1 (VDE 0115-103-1) Generic RAMS process
- Part 2 (VDE 0115-103-2) System-related safety methodology
DIN EN 50128 (VDE 0831-128) Railway applications - Telecommunication technology, signaling technology and data processing systems - Software for railway control and monitoring systems
DIN EN 50129 (VDE 0831-129) Railway applications - Telecommunication technology, signal technology and data processing systems - Safety-related electronic systems for signal technology
DIN EN 50131 Alarm systems - intrusion and hold-up alarm systems
- Part 1 system requirements
- Part 2-2 intrusion alarms
- Part 2-3 Requirements for microwave detectors (DIN CLC / TS 50131-2-3)
- Part 2-4 requirements for combined passive infrared and microwave detectors (DIN CLC / TS 50131-2-4)
- Part 2-5 requirements for combined passive infrared and ultrasonic detectors (DIN CLC / TS 50131-2-5)
- Part 2-6 Requirements for opening detectors (magnetic contacts) (DIN CLC / TS 50131-2-6)
- Part 3 alarm center
- Part 4 signal transmitter
- Part 5-3 Requirements for transmission equipment using radio frequency techniques
- Part 6 power supplies
- Part 7 application rules
- Part 8 fog devices / fog systems for security applications
DIN EN 50132 CCTV surveillance systems for security applications
DIN EN 50133 Alarm systems - Access control systems for security applications
- Part 1 system requirements
- Part 2-1 General requirements for system components
- Part 7 application rules
DIN EN 50155 (VDE 0115-200) Railway applications - Electronic equipment on railway vehicles
DIN EN 50159 (VDE 0831-159) Railway applications - Telecommunication technology, signaling technology and data processing systems - Safety-relevant communication in transmission systems
DIN EN 50172 safety lighting systems
DIN EN 50173 (VDE 0800-173) Information technology - application-neutral communication cable systems
- Part 1 General Requirements
- Part 1 Supplement 1 cabling guide to support 10 GBASE-T
- Part 2 office building
- Part 3 Industrial locations
- Part 4 apartments
- Part 4 Supplement 1 Realization of RuK network applications with cabling according to EN 50173-4
- Part 4 Supplement 2 Infrastructure of home cabling up to 50 m in length for the simultaneous or non-simultaneous provision of network applications
- Part 5 data centers
DIN EN 50174 (VDE 0800-174) Information technology - Installation of communication cabling
- Part 1 installation specification and quality assurance
- Part 2 Installation planning and installation practices in buildings
- Part 2 supplement 1 remote power supply
- Part 3 Installation planning and outdoor installation practices
DIN EN 50191 (VDE 0104) Installation and operation of electrical test systems
DIN EN 50215 (VDE 0115-101) Railway applications - Railway vehicles - Testing of railway vehicles after completion and before commissioning
DIN EN 50272 safety requirements for batteries and battery systems
- Part 1 (VDE 0510-1) General safety information
- Part 2 (VDE 0510-2) Stationary batteries
- Part 3 (VDE 0510-3) Drive batteries for electric vehicles
- Part 4 (VDE 0510-104) batteries for portable devices
DIN EN 50285 Energy efficiency of electrical lamps for household use - measurement methods
DIN EN 50286 (VDE 0682-301) Electrically insulating protective clothing for work on low-voltage systems
DIN EN 50294 (VDE 0712-294) Procedure for measuring the total input power of ballast-lamp-circuits
DIN EN 50311 (VDE 0115-450) Railway applications - Railway vehicles - DC-supplied electronic ballasts for fluorescent lamps
DIN EN 50523 devices for household use - interworking
- Part 1 functional specification
- Part 2 data structures
DIN EN 50581 (VDE 0042-12) Technical documentation for the assessment of electrical and electronic devices with regard to the restriction of hazardous substances
DIN EN 55022 (VDE 0878-22) Information technology equipment - Radio interference properties - Limit values and measurement methods

DIN EN 60000–99999

DIN EN 60044 measuring transducer

Part 1: current transformers
Part 2: Inductive voltage converters (2012-05 replaced by DIN EN 61869-3)
Part 3: Combined converters
Part 6: Requirements for current transformers for protection purposes for transmission for transient transmission behavior
Part 7: Electronic voltage converters
Part 8: Electronic current transformers

DIN EN 60051 Direct-acting indicating measuring devices and their accessories - Measuring devices with scale display -

DIN EN 60061 lamp bases and sockets as well as gauges for checking interchangeability and safety

Part 1 lamp base (IEC 60061-1)
Part 2 lamp sockets (IEC 60061-2)

DIN EN 60062 marking of resistors and capacitors, including date of manufacture and thus replaces DIN 41314.

DIN EN 60064 Incandescent lamps for household use and similar general lighting purposes - Requirements for the mode of operation (IEC 60064)

DIN EN 60081 Double capped fluorescent lamps - Requirements for the mode of operation (IEC 60081)

DIN EN 60155 (VDE 0712-101) Glow starter for fluorescent lamps (IEC 60155)

DIN EN 60188 high pressure mercury vapor lamps - Requirements for the mode of operation (IEC 60188)

DIN EN 60192 low pressure sodium vapor lamps - Requirements for the mode of operation (IEC 60192)

DIN EN 60204 Safety of machines - Electrical equipment of machines

Part 1 General Requirements

DIN EN 60255 measuring relays and protective devices

Part 1 General Requirements
Part 5 insulation coordination for measuring relays and protective devices; Requirements and tests
Part 5 Supplement 1 Insulation coordination for measuring relays and protective devices; Requirements and tests; Explanations of the standard
Part 8 overload relays
Part 11 voltage dips, short-term interruptions, voltage fluctuations and alternating portion in connection for the auxiliary power supply
Part 21-1 Vibration, shock, continuous shock and earthquake tests on measuring relays and protective devices; Main section 1: Vibration tests (sinusoidal)
Part 21-2 Vibration, shock, continuous shock and earthquake tests on measuring relays and protective devices; Main section 2: Shock and continuous shock tests
Part 21-3 Vibration, shock, continuous shock and earthquake tests on measuring relays and protective devices; Main Section 3: Earthquake Tests
Part 22-1 Tests of electrical interference immunity - Testing of interference immunity against 1 MHz interference
Part 22-2 Tests of electrical interference immunity - Tests with electrostatic discharge
Part 22-3 Testing of electrical immunity - Testing of immunity to electromagnetic fields
Part 22-4 Tests of the electrical interference immunity - Testing of the interference immunity against fast transient electrical disturbances / burst
Part 22-5 Testing of the electrical interference immunity of measuring relays and protective devices; Testing of immunity to surge voltages
Part 22-6 Tests of the electrical interference immunity of measuring relays and protective devices; Immunity to conducted disturbances induced by high-frequency fields
Part 22-7 Tests of the electrical interference immunity of measuring relays and protective devices - Testing of the interference immunity against line-frequency disturbances
Part 24 standard format for the exchange of transient data in electrical energy supply networks
Part 25 Tests of electromagnetic interference emission for measuring relays and protective devices
Part 26 requirements for electromagnetic compatibility
Part 27 requirements for product safety
Part 151 functional requirements for over / under current protection

DIN EN 60384 fixed capacitors for use in electronic devices

Part 1 basic specification (VDE 0565-1)
Part 2… 25 various specifications

DIN EN 60400 (VDE 0616-3) lamp sockets for tubular fluorescent lamps and starter sockets (IEC 60400)

DIN EN 60439 low-voltage switchgear assemblies
- Part 1 Type-tested and partially type-tested combinations
- Part 2 Special requirements for busbar trunking systems
- Part 3 Special requirements for low-voltage switchgear assemblies which laymen have access to operate; Installation distributor
- Part 4 Special requirements for site power distributors (BV)
- Part 5 Special requirements for low-voltage switchgear assemblies that are set up outdoors in publicly accessible places; Cable distribution cabinets (KVS) in energy supply networks
DIN EN 60529 (VDE 0470-1) Protection classes through housing (IP code) (IEC 60529)
DIN EN 60598 lights
- Part 1 (VDE 0711-1) General requirements and tests (IEC 60598-1)
- Part 2 Special requirements
  - Part 2-2 (VDE 0711-2-2) Recessed lights (IEC 60598-2-2)
  - Part 2-3 (VDE 0711-2-3) Luminaires for street and path lighting (IEC 60598-2-3)
  - Part 2-4 (VDE 0711-2-4) Portable luminaires for general purposes (IEC 60598-2-4)
  - Part 2-5 (VDE 0711-2-5 :) Headlights (IEC 60598-2-5)
  - Part 2-6 (VDE 0711-206) luminaires with built-in transformers for incandescent lamps (IEC 60598-2-6)
  - Part 2-7 Portable garden lights (IEC 60598-2-7)
  - Part 2-8 (VDE 0711-2-8) Hand lamps (IEC 60598-2-8)
  - Part 2-9 (VDE 0711-2-9) Photo and film lights (not professional use) (IEC 60598-2-9)
  - Part 2-10 (VDE 0711-2-10) Portable lights for children (IEC 60598-2-10)
  - Part 2-11 (VDE 0711-2-11) Aquarium lights (IEC 60598-2-11)
  - Part 2-12 (VDE 0711-2-12) Power socket night lights (IEC 60598-2-12)
  - Part 2-13 (VDE 0711-2-13) In-ground luminaires (IEC 60598-2-13)
  - Part 2-18 (VDE 0711-2-18) Luminaires for swimming pools and similar applications (IEC 60598-2-18)
  - Part 2-19 (VDE 0711-2-19) Air-conducting lights (safety requirements)
  - Part 2-20 (VDE 0711-2-20) light chains (IEC 60598-2-20)
  - Part 2-22 (VDE 0711-2-22) lights for emergency lighting
  - Part 2-23 (VDE 0711-2-23) Low voltage lighting systems for incandescent lamps (IEC 60598-2-23)
  - Part 2-24 (VDE 0711-2-24) Luminaires with limited surface temperature (IEC 60598-2-24)
  - Part 2-25 (VDE 0711-2-25) Luminaires for use in clinical areas of hospitals and buildings for health care (IEC 60598-2-25)
DIN EN 60601 Medical electrical equipment, safety
DIN EN 60603 connectors for printed circuits for frequencies below 3 MHz
- Part 1 Generic specification: General requirements and guidelines for the creation of type specifications with quality assessment (IEC 60603-1)
- Part 2 design specification for quality-assessed indirect connectors for printed circuits, pitch 2.54 mm (0.1 in), with common installation features (IEC 60603-2)
- Part 3 Indirect connectors for printed circuits with 2.54 mm (0.1 in) contact spacing and staggered connections at the same distance (IEC 60603-3)
- Part 4 Indirect connectors for printed circuits with 1.91 mm (0.075 in) contact spacing and staggered connections at the same distance (IEC 60603-4)
- Part 5 Connectors for direct mating and indirect connectors for circuit boards coated on both sides with 2.54 mm (0.1 in) contact spacing (IEC 60603-5)
- Part 6 Direct connectors and connectors for printed circuits with 2.54 mm (0.1 in) contact spacing for printed circuit boards coated on one or both sides with 1.6 mm (0.063 in) nominal thickness (IEC 60603-6)
- Part 7 detail specification for connectors with assessed quality, 8-pin, including fixed and free connectors with common mating characteristics (IEC 60603-7)
- Part 7-1 design specification for shielded free and fixed connectors, 8-pole, with common plug characteristics and assessed quality (IEC 60603-7-1)
- Part 7-3 design specification for shielded free and fixed connectors, 8-pin, for data transmission up to 100 MHz (IEC 48B / 1707 / CDV)
- Part 7-4 design specification for unshielded free and fixed connectors, 8-pin, for data transmission up to 250 MHz (IEC 60603-7-4)
- Part 7-7 design specification for shielded free and fixed connectors, 8-pin, for data transmission up to 600 MHz (IEC 60603-7-7)
- Part 8 Indirect connectors for printed circuits; Pitch 2.54 mm (0.1 in); Cross section of the male contacts 0.63 mm × 0.63 mm (IEC 60603-8)
- Part 9 Indirect connectors for printed circuits, back plates and cable termination; Grid dimension 2.54 mm (0.1 in) (IEC 60603-9)
- Part 10 Indirect connectors for printed circuits with a pitch of 2.54 mm (0.1 in), inverted design (IEC 60603-10)
- Part 12 detail specification for dimensions, general requirements and tests for a number of sockets to accommodate integrated circuits (IEC 60603-12)
- Part 13 design specification for quality-assessed indirect connectors for printed circuits with pitch 2.54 mm (0.1 in), with free connector for insulation displacement connection (ID) (IEC 60603-13)
- Part 14 detail specification for circular connectors for low frequency audio and video applications such as audio, video and audiovisual equipment (IEC 60603-14)
DIN EN 60617 Graphic symbols for circuit diagrams
DIN EN 60662 high pressure sodium vapor lamps (IEC 60662)
DIN EN 60721 classification of environmental conditions
- Part 1 preferred values for influencing variables
- Part 3 classes of environmental influencing variables and their limit values
  - Part 3-0 introduction
  - Part 3-1 Long Term Storage
  - Part 3-2 Transport
  - Part 3-3 Stationary use, weatherproof
  - Part 3-4 Fixed use, not protected from the weather
  - Part 3-5 Use on and in land vehicles
  - Part 3-6 Use on ships
  - Part 3-7 Mobile use
  - Part 3-9 Microclimates within articles
DIN EN 60730 Automatic electrical regulating and control devices for household use and similar applications ( VDE 0631 )
- Part 1 General Requirements
- Part 2 special requirements (various standards)
DIN EN 60751 Industrial platinum resistance thermometers and platinum temperature sensors
DIN EN 60825 Safety of laser equipment
- Supplement 1 National wording of the information signs for laser radiation
- Supplement 9 Summary of the maximum permissible exposure to incoherent optical radiation
- Supplement 10 Application guidelines and explanatory notes on IEC 60825-1
- Supplement 14: A Guide for Users
- Part 1 Classification of facilities and requirements
- Part 2 Security of fiber optic communication systems (LWLKS)
- Part 2 Supplement 1 Safety of fiber optic communication systems (LWLKS), layout sheet 1
- Part 4 laser protection walls
- Part 12 Security of optical free space communication systems for the transmission of information
DIN EN 60848 GRAFCET specification language for function charts of the sequence control

DIN EN 60870 telecontrol equipment and systems (IEC 60870)

Part 1 General considerations, technical report
Part 2 operating conditions
Part 3 interfaces (electrical characteristics)
Part 4 Requirements for the performance characteristics
Part 5 transmission protocols
Part 6 telecontrol protocols

DIN EN 60901 Single-capped fluorescent lamps - Requirements for the mode of operation (IEC 60901)

DIN EN 60921; VDE 0712-11 Ballasts for tubular fluorescent lamps - Requirements for the mode of operation (IEC 60921)

DIN EN 60923 VDE 0712-13 Devices for lamps - Ballasts for discharge lamps (with the exception of tubular fluorescent lamps) - Functional requirements (IEC 60923)

DIN EN 60925; VDE 0712-21 DC-supplied electronic ballasts for tubular fluorescent lamps - Requirements for the mode of operation (IEC 60925)

DIN EN 60927; VDE 0712-15 Devices for lamps - Starting devices (other than glow starters) - Requirements for the mode of operation (IEC 60927)

DIN EN 60929; VDE 0712-23 AC-powered electronic ballasts for tubular fluorescent lamps - Requirements for the mode of operation (IEC 60929)

DIN EN 60947 low-voltage switchgear

DIN EN 60968; VDE 0715-6: 2000-04 lamps with built-in ballast for general lighting - safety requirements (IEC 60968)

DIN EN 60969 lamps with built-in ballast for general lighting - requirements for operation (IEC 60969)

DIN EN 61000 EMC Electromagnetic Compatibility

Part 1 Overview of the IEC 61000-4 series
Part 2 Test of immunity to static electricity discharge
Part 3 Testing of immunity to high-frequency electromagnetic fields
Part 4 Testing of immunity to fast transient electrical disturbances / bursts
Part 5 Testing of immunity to surge voltages
Part 6 Immunity to conducted disturbances, induced by high-frequency fields
Part 7 General guidelines for methods and devices for measuring harmonics and interharmonics in power supply networks and connected devices
Part 8 Testing of immunity to magnetic fields with energy-related frequencies
Part 9 Testing of immunity to pulsed magnetic fields
Part 10 Testing of immunity to dampened oscillating magnetic fields
Part 11 Testing of immunity to voltage dips, short interruptions and voltage fluctuations
Part 12 Testing of immunity to damped sinusoidal oscillations
Part 13 Testing of interference immunity at the AC mains connection against harmonics and interharmonics, including conducted interference from signal transmission on electrical low-voltage networks
Part 14 test of immunity to voltage fluctuations
Part 15 Flicker meter - functional description and design specification
Part 16 Testing of immunity to conducted, asymmetrical interference in the frequency range from 0 Hz to 150 kHz
Part 17 Testing of interference immunity against alternating components of the voltage at direct current mains connections
Part 18 test of immunity to vibrating waves
Part 20 Measurement of emitted interference and immunity to interference in transverse electromagnetic waveguides
Part 21 procedures for testing in the mode swirl chamber
Part 23 test methods for devices for protection against HEMP and other radiated disturbances
Part 24 test methods for devices for protection against conducted HEMP disturbances - EMC basic standard
Part 25 Testing of interference immunity of facilities and systems against HEMP interference
Part 27 test of the immunity to unbalance of the supply voltage
Part 28 Test of immunity to fluctuations in the power frequency
Part 29 Testing of interference immunity against voltage dips, short-term interruptions and voltage fluctuations at direct current network inputs
Part 30 procedure for measuring the voltage quality
Part 33 Testing of interference immunity of devices and facilities with an input current> 16 A per conductor against voltage dips, short interruptions and voltage fluctuations

DIN EN 61010 Safety regulations for electrical measuring, control, regulating and laboratory devices ( VDE 0411 )

Part 1 General Requirements
Part 2-010 Special requirements for laboratory equipment for heating substances
Part 2-020 Special requirements for laboratory centrifuges
Part 2-032 Special requirements for hand-held and hand-operated current probes for electrical measurements
Part 2-040 Special requirements for sterilizers and washer-disinfectors for the treatment of medical material
Part 2-051 Special requirements for laboratory equipment for mixing and stirring
Part 2-061 Special requirements for laboratory atomic spectrometers with thermal atomization and ionization
Part 2-081 Special requirements for automatic and semi-automatic laboratory equipment for analysis and other purposes
Part 2-101 Special requirements for in vitro diagnostic (IVD) medical devices
Part 031 Safety regulations for hand-held measuring accessories for measuring and testing

DIN EN 61048 (VDE 0560-61) Devices for lamps - Capacitors for fluorescent lamp and other discharge lamp circuits - General requirements and safety requirements (IEC 61048)

DIN EN 61049; VDE 0560-62 capacitors for discharge lamp systems, especially fluorescent lamp systems; Performance requirements (IEC 61049)

DIN EN 61131 Programmable Logic Controllers (PLC)

Part 1 General information (IEC 61131-1)
Part 2 Equipment requirements and tests (IEC 61131-2)
Part 3 programming languages (IEC 61131-3)
Part 5 communication (IEC 61131-5)
Part 7 Fuzzy Control Programming (IEC 61131-7)

DIN EN 61140 (VDE 0140-1) Protection against electric shock - Common requirements for systems and equipment (IEC 61140)

DIN EN 61167 metal halide lamps (IEC 61167)

DIN EN 61195; VDE 0715-8 Double capped fluorescent lamps - safety requirements (IEC 61195)

DIN EN 61199; VDE 0715-9 Single capped fluorescent lamps - Safety requirements (IEC 61199)

DIN EN 61228 UV fluorescent lamps for tanning purposes - Methods of measurement and description (IEC 61228)

DIN EN 61305 Hi-Fi devices and systems for home use - Procedure for measuring and specifying performance parameters

Part 1 General
Part 2 FM broadcast receiving parts
Part 3 amplifier
Part 5 speakers
Part 5 Supplement 1 hearing tests for loudspeakers - individual test methods and pair comparison

DIN EN 61326 Electrical measuring, control, regulating and laboratory equipment EMC requirements

Part 1 General Requirements
Part 2-1 Special requirements - test setup, operating conditions and performance characteristics for sensitive test and measuring devices for applications without EMC protective measures
Part 2-2 Special requirements - test arrangement, operating conditions and performance characteristics for portable test, measuring and monitoring devices for use in low-voltage power supply networks
Part 2-3 Special requirements for measuring transducers with integrated or remote signal processing
Part 2-4 special requirements - test arrangement, operating conditions and performance characteristics for insulation monitoring devices
Part 2-5 special requirements - test arrangements, operating conditions and performance characteristics for field devices with fieldbus interfaces
Part 2-6 special requirements - medical in vitro diagnostic devices (IVD)
Part 3-1 Immunity requirements for safety-related systems and for devices that are intended for safety-related functions (functional safety) - General industrial applications
Part 3-2 Immunity requirements for safety-related systems and for devices that are intended for safety-related functions (functional safety) - Industrial applications in a specified electromagnetic environment

DIN EN 61346 Industrial systems, plants and equipment and industrial products - Structuring principles and reference identification

Part 1 General rules
Part 2 Classification of objects and coding of classes

DIN EN 61347 devices for lamps

Part 1 (VDE 0712-30) General and safety requirements (IEC 61347-1)
Part 2 Special requirements
- Part 2-1 (VDE 0712-31) Special requirements for starting devices (other than glow starters) (IEC 61347-2-1)
- Part 2-2 (VDE 0712-32) Special requirements for DC or AC supplied electronic converters for incandescent lamps (IEC 61347-2)
- Part 2-3 (VDE 0712-33) Special requirements for AC-powered electronic ballasts for fluorescent lamps (IEC 61347-2-3)
- Part 2-4 (VDE 0712-34) Special requirements for DC-powered electronic ballasts for general lighting (IEC 61347-2-4)
- Part 2-5 (VDE 0712-35) Special requirements for DC-supplied electronic ballasts for lighting public transport (IEC 61347-2-5)
- Part 2-6 (VDE 0712-36) Special requirements for DC-supplied electronic ballasts for the lighting of aircraft (IEC 61347-2-6)
- Part 2-7 (VDE 0712-37) Special requirements for DC-supplied electronic ballasts for emergency lighting (IEC 61347-2-7)
- Part 2-8 (VDE 0712-38) Special requirements for ballasts for fluorescent lamps (IEC 61347-2-8)
- Part 2-9 (VDE 0712-39) Special requirements for ballasts for discharge lamps (except fluorescent lamps) (IEC 61347-2-9)
- Part 2-10 (VDE 0712-40) Special requirements for electronic inverters and converters for high-frequency operation of tubular cold start discharge lamps (neon tubes) (IEC 61347-2-10)
- Part 2-11 (VDE 0712-41) Special requirements for electronic modules for lights (IEC 61347-2-11)
- Part 2-12 (VDE 0712-42) Special requirements for DC or AC supplied electronic ballasts for discharge lamps (except for fluorescent lamps) (IEC 61347-2-12)
- Part 2-13 (VDE 0712-43) Special requirements for DC or AC supplied electronic control gear for LED modules (IEC 61347-2-13)

DIN EN 61355 Classification and marking of documents for plants, systems and facilities

DIN EN 61439 low-voltage switchgear assemblies
- Part 1 General specifications
- Part 2 power switchgear assemblies
- Part 3 distribution boards for operation by laypersons (IVL)
- Part 5 switchgear assemblies in public energy distribution networks
- Part 6 busbar trunking systems (busways)
DIN EN 61499 function blocks
for industrial control systems (IEC 61499)
- Part 1 architecture
- Part 2 Requirements for software tools
- Part 4 rules for standardized profiles

DIN EN 61508 Functional safety of safety-related electrical / electronic / programmable electronic systems (VDE 0803)

Part 0 (VDE 0803 supplement 1) Functional safety and IEC 61508 (IEC / TR 61508-0)
Part 1 (VDE 0803-1) General requirements (IEC 61508-1)
Part 2 (VDE 0803-2) Requirements for safety-related electrical / electronic / programmable electronic systems (IEC 61508-2)
Part 3 (VDE 0803-3) Requirements for software (IEC 61508-3)
Part 4 (VDE 0803-4) Terms and abbreviations (IEC 61508-4)
Part 5 (VDE 0803-5) Examples and methods for the determination of safety integrity levels (IEC 61508-5)
Part 6 (VDE 0803-6) Application guideline for IEC 61508-2 and IEC 61508-3 (IEC 61508-6)
Part 7 (VDE 0803-7) Application notes on procedures and measures (IEC 61508-7)

DIN EN 61549; VDE 0715-12 special lamps (IEC 61549)

DIN EN 61672 electroacoustics - sound level meter

Part 1 requirements (IEC 61672-1)
Part 2 type tests (IEC 61672)
Part 3 Periodic individual test (IEC 61672-3)

DIN EN 61669 electroacoustics - Devices for measuring the characteristics of hearing aids on the human ear (IEC 61669: 2001)

DIN EN 61724 Monitoring the operational behavior of photovoltaic systems - Guidelines for measurement, data exchange and analysis (IEC 61724: 1998)

DIN EN 61725 Analytical representation for solar daily radiation profiles (IEC 61725: 1997)

DIN EN 61800 Adjustable speed electrical drives

Part 1 (VDE 0160 Part 101) General requirements - definition for the dimensioning of low-voltage direct current drive systems - (IEC 61800-1)
Part 2 (VDE 0160 Part 102) General requirements - definition for the dimensioning of low-voltage direct current drive systems with adjustable frequency - (IEC 61800-2)
Part 3 (VDE 0160 Part 103) EMC requirements including special test methods (IEC 61800-3)
Part 4 (VDE 0160 Part 104) General requirements; Specifications for the dimensioning of AC drive systems over 1,000 V AC and a maximum of 35 kV (IEC 61800-4)
Part 5-1 (VDE 0160 Part 105) requirements for safety; Electrical, thermal and energetic requirements (IEC 61800-5-1)

DIN EN 61850 communication networks and systems in stations (IEC 61850)

Supplement 1 Introduction and Overview
Part 3 General Requirements
Part 4 system and project management
Part 5 communication requirements for functions and device models
Part 6 Language for the description of the configuration for communication in stations with intelligent electronic devices (IED)
Part 7 Basic communication structure for station and field-related equipment
- Part 7-1 Principles and Models
- Part 7-2 Abstract Interface for Communication Services (ACSI)
- Part 7-3 Common data classes
- Part 7-4 Compatible logic node and data classes
Part 7-410 Communication networks and systems for automation in electrical energy supply - Part 7-410: Hydroelectric power plants - Communication for monitoring, regulation and control (IEC 61850-7-410)
Part 7-420 communication systems for distributed energy supply - logical nodes
Part 8-1 Specific mapping of communication services (SCSM) - mapping on MMS (according to ISO 9506-1 and ISO 9506-2) and ISO / IEC 8802-3
Part 9-1 Specific mapping of communication services (SCSM) - sampled values over serial simplex multiple point-to-point connection
Part 9-2 Specific mapping of communication services (SCSM) - sampled values via ISO / IEC 8802-3
Part 10 conformity test

DIN EN 61920 Non-conducted infrared applications (IEC 61920: 2004)

DIN EN 61947 Electrical projection - Measurement and documentation of important performance characteristics

Part 1 fixed resolution projectors
Part 2 projectors of variable resolution

DIN EN 61966 Multimedia systems and devices - Color measurement and color management

Part 2 color management
- Part 2-1 Default RGB color space, sRGB (IEC 61966-2-1)
- Part 2-2 Extended RGB color space, scRGB (IEC 61966-2-2)
- Part 2-4 Extended YCC color space for video applications - xvYCC (IEC 61966-2-4)
- Part 2-5 Optional RGB color space - opRGB (IEC 61966-2-5)
Part 3 devices with cathode ray tubes (IEC 61966-3)
Part 4 devices with liquid crystal displays (IEC 61966-4)
Part 5 devices with plasma displays (IEC 61966-5)
Part 6 Electronic projectors for front projection (IEC 61966-6)
Part 7 color printer
- Part 7-1 Reflective prints - RGB inputs (IEC 61966-7-1)
Part 8 Multimedia color scanner (IEC 61966-8)
Part 9 digital cameras (IEC 61966-9)

DIN EN 61988 plasma screens

Part 1 Terminology and letter symbols (IEC 61988-1)
Part 2 measurement method
- Part 2-1 Optical (IEC 61988-2-1)
- Part 2-2 Opto-Electrical (IEC 61988-2-2)
Part 3-1 mechanical interface (IEC 61988-3-1)
Part 4 environmental, service life and mechanical test methods (IEC 61988-4)

DIN EN 62031 (VDE 0715-5) LED modules for general lighting - safety requirements (IEC 62031)

DIN EN 62034 (VDE 0711-400) Automatic test systems for battery-operated safety lighting for escape routes (IEC 62034)

DIN EN 62035; VDE 0715-10 discharge lamps (except fluorescent lamps) - safety requirements (IEC 62035)

DIN EN 62079 Preparation of instructions - structure, content and presentation (withdrawn and replaced by EN 82079 )

DIN EN 62106 specification of the radio data system (RDS)

DIN EN 62264 Integration of corporate IT and control systems

Part 1 models and terminology (draft standard DIN IEC 62264-1)
Part 2 attributes of the object model (draft standard DIN IEC 62264-2)
Part 3 activity models for operational production management

DIN EN 62304 Medical device software - Software life cycle processes

DIN EN 62563 Medical electrical equipment - Medical image display systems

Part 1 assessment methods (IEC 62563-1: 2009)

DIN EN 80000 sizes and units

Part 6 electromagnetism

DIN EN 80601 Medical electrical equipment, safety

DIN EN 82045 document management

Part 1 Principles and Methods (IEC 82045-1: 2001)
Part 2 metadata and information reference models (IEC 82045-2: 2004)

DIN EN 82079 Preparation of instructions - structure, content and presentation

DIN EN 88528 Power generating sets with reciprocating internal combustion engines

Part 11 Dynamic Uninterruptible Power Supply - Performance Requirements and Test Methods

DIN EN from 100000

DIN EN 100012 basic specification: X-ray fluoroscopy of electronic components
DIN EN 300366 Private Integrated Services Networks (PISN) - Signaling between telecommunications systems - "Callback" service features
DIN EN 383001 Telecommunication and Internet services and protocols for advanced networks (TISPAN) - interaction between the session initiation protocol (SIP) and the transmission-independent connection control protocol (BICC) or ISDN user part (ISUP)