Solar energy

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Hertz1888 (talk | contribs) at 05:30, 8 July 2008 (→‎See also: clarifying nature of article). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Heat and light from the Sun fuels life on Earth.
Nellis Solar Power Plant, the largest photovoltaic power plant in North America
Solar energy reaching the earth's surface (left) greatly exceeds both total wind energy (center) and global energy consumption (right), although only a small portion of each is recoverable.[1]
Part of a series on
Renewable energy

Solar energy is the heat and light radiated from the Sun that powers Earth's climate and supports life. Solar technologies allow controlled use of this energy resource. Solar power is a synonym of solar energy or refers specifically to the conversion of sunlight into electricity by photovoltaics, concentrating solar thermal devices and various experimental technologies.

The controlled use of solar energy is an important consideration in building design. Thermal mass is used to conserve the heat that sunshine delivers to all buildings. Daylighting techniques optimize the use of light in buildings. Solar water heaters heat swimming pools and provide domestic hot water. In agriculture, greenhouses grow specialty crops and photovoltaic-powered pumps provide water for grazing animals. Evaporation ponds find applications in the commercial and industrial sectors where they are used to harvest salt and clean waste streams of contaminants.

Solar distillation and disinfection techniques produce potable water for millions of people worldwide. Family-scale solar cookers and larger solar kitchens concentrate sunlight for cooking, drying and pasteurization. More sophisticated concentrating technologies magnify the rays of the Sun for high-temperature material testing, metal smelting and industrial chemical production. A range of prototype solar vehicles provide ground, air and sea transportation.

Energy from the Sun

Main articles: Insolation and Solar radiation
About half the incoming solar energy is absorbed by water and land; the rest is reradiated back into space.
Average insolation showing land area (small black dots) required to replace the total world energy supply with solar electricity

Earth continuously receives 174 PW of incoming solar radiation (insolation) at the upper atmosphere.[2] Approximately 30% is reflected back to space while the rest is absorbed by the atmosphere, oceans and land masses. After passing through the atmosphere, the insolation spectrum is mostly split between the visible and infrared ranges with a small part in the ultraviolet.[3]

The absorption of solar energy by atmospheric convection (sensible heat transport) and evaporation and condensation of water vapor (latent heat transport) powers the water cycle and drives the winds.[4] Sunlight absorbed by the oceans and land masses keeps the surface at an average temperature of 14 °C.[5] The conversion of solar energy into chemical energy via photosynthesis produces food, wood and the biomass from which fossil fuels are derived.[6]

Solar radiation along with secondary solar resources such as wind and wave power, hydroelectricity and biomass account for over 99.9% of the available flow of renewable energy on Earth.[7][8] The flows and stores of solar energy in the environment are vast in comparison to current human energy needs.

  • The total solar energy absorbed by Earth's atmosphere, oceans and land masses is approximately 3,850 zettajoules (ZJ) per year.[9]
  • Global wind energy at 80 m is estimated at 2.25 ZJ per year.[10]
  • Photosynthesis captures approximately 3 ZJ per year in biomass.[11]
  • Worldwide electricity consumption was approximately 0.0567 ZJ in 2005.[12]
  • Worldwide primary energy consumption was 0.487 ZJ in 2005.[13]

Applications of solar energy technology

Solar radiation spectrum

Solar energy technologies use solar radiation for practical ends. Technologies that use secondary solar resources such as biomass, wind, waves and ocean thermal gradients can be included in a broader description of solar energy but only primary resource applications are discussed here. Because the performance of solar technologies varies widely between regions, solar technologies should be deployed in a way that carefully considers these variations.[14]

Solar technologies such as photovoltaics and water heaters increase the supply of energy and may be characterized as supply side technologies.[citation needed] Technologies such as passive design and shading devices reduce the need for alternate resources and may be characterized as demand side. Optimizing the performance of solar technologies is often a matter of controlling the resource rather than simply maximizing its collection.[citation needed]

Architecture and urban planning

Main articles: Passive solar building design and Urban heat island
Darmstadt University of Technology won the 2007 Solar Decathlon with this passive house designed specifically for the humid and hot subtropical climate in Washington, D.C.[15]

Sunlight has influenced building design since the beginning of architectural history.[16] Fully developed solar architecture and urban planning methods were first employed by the Greeks and Chinese who oriented their buildings toward the south to provide light and warmth.[17]

The elemental features of passive solar architecture are Sun orientation, compact proportion (a low surface area to volume ratio), selective shading (overhangs) and thermal mass.[16] When these features are tailored to the local climate and environment they can produce well-lit spaces that stay in a comfortable temperature range. Socrates' Megaron House is a classic example of passive solar design.[16] The most recent approaches to solar design use computer modeling to tie together solar lighting, heating and ventilation systems in an integrated solar design package. Active solar equipment such as pumps, fans and switchable windows can also complement passive design and improve system performance.

Urban heat islands (UHI) are metropolitan areas with higher temperatures than the surrounding environment. These higher temperatures are the result of urban materials such as asphalt and concrete that have lower albedos and higher heat capacities than the natural environment. A straightforward method of counteracting the UHI effect is to paint buildings and roads white and plant trees. Using these methods, a hypothetical "cool communities" program in Los Angeles has projected that urban temperatures could be reduced by approximately 3 °C at an estimated cost of US$1 billion, giving estimated total annual benefits of US$530 million from reduced air-conditioning costs and healthcare savings.[18]

Agriculture and horticulture

Main articles: Agriculture, Horticulture, and Greenhouse
Greenhouses like these in the Netherland's Westland municipality grow a wide variety of vegetables, fruits and flowers.

Agriculture inherently seeks to optimize the capture of solar energy, and thereby plant productivity. Techniques such as timed planting cycles, tailored row orientation, staggered heights between rows and the mixing of plant varieties can improve crop yields.[19][20] While sunlight is generally considered a plentiful resource, there are exceptions which highlight the importance of solar energy to agriculture. During the short growing seasons of the Little Ice Age, French and English farmers employed fruit walls to maximize the collection of solar energy. These walls acted as thermal masses and accelerated ripening by keeping plants warm. Early fruit walls were built perpendicular to the ground with a south facing orientation but over time sloping walls were developed to make better use of sunlight. In 1699, Nicolas Fatio de Duillier even suggested using a tracking mechanism which could pivot to follow the Sun.[21] Solar energy is also used in many areas of agriculture aside from growing crops. Applications include pumping water, drying crops, brooding chicks and drying chicken manure.[22][23]

Greenhouses control the use of solar heat and light to grow plants in enclosed environments, enabling year-round production and the growth of specialty crops and other plants not naturally suited to the local climate. Primitive greenhouses were first used during Roman times to grow cucumbers year-round for the Roman emperor Tiberius.[24] The first modern greenhouses were built in Europe in the 16th century to conserve exotic plants brought back from explorations abroad.[25] Greenhouses remain an important part of horticulture today, while plastic transparent materials have also been used to similar effect in polytunnels and row covers.

Solar lighting

Daylighting features such as this oculus at the top of the Pantheon in Rome have been in use since antiquity.

The history of lighting is dominated by the use of natural light. The Romans recognized the Right to Light as early as the 6th century and English law echoed these judgments with the Prescription Act of 1832.[26][27] In the 20th century artificial lighting became the main source of interior illumination.

Daylighting systems collect and distribute sunlight to provide interior illumination. These systems directly offset energy use by replacing artificial lighting, and indirectly offset non-solar energy use by reducing the need for air-conditioning.[28] Although difficult to quantify, the use of natural lighting also offers physiological and psychological benefits compared to artificial lighting.[28] Daylighting design carefully selects window type, size and orientation and may also consider exterior shading devices. Individual features include sawtooth roofs, clerestory windows, light shelves, skylights and light tubes. These features may be incorporated into existing structures but are most effective when integrated in a solar design package that accounts for factors such as glare, heat flux and time-of-use. When daylighting features are properly implemented they can reduce commercial lighting-related energy requirements by 25%.[29]

Hybrid solar lighting (HSL) is an active solar method of using sunlight to provide illumination. HSL systems collect sunlight using focusing mirrors that track the Sun and use optical fibers to transmit the light into a building's interior to supplement conventional lighting. In single-story applications, these systems are able to transmit 50% of the direct sunlight received.[30]

Although daylight saving time is promoted as a way to use sunlight to save energy, recent research is limited and reports contradictory results: several studies report savings, but just as many suggest no effect or even a net loss, particularly when gasoline consumption is taken into account. Electricity use is greatly affected by geography, climate and economics, making it hard to generalize from single studies.[31]

Solar thermal

Main article: Solar thermal energy

Solar thermal technologies can be used for water heating, space heating, space cooling and process heat generation.[32]

Water heating

Main articles: Solar hot water and Solar combisystem
Solar water heaters face the equator and are angled according to latitude to maximize solar gain.

Solar hot water systems use sunlight to heat water. When sited in low latitudes (below 40 degrees), solar heating system can provide around 60 to 70% of domestic hot water use with temperatures up to 60 °C.[33] The most common types of solar water heaters are evacuated tube collectors (44%) and glazed flat plate collectors (34%) generally used for domestic hot water; and unglazed plastic collectors (21%) used mainly to heat swimming pools.[34]

As of 2007, the total installed capacity of solar hot water systems is approximately 154 GW.[35] China is the world leader in the deployment of solar hot water with 70 GW installed as of 2006 and a long term goal of 210 GW by 2020.[36] Israel is the per capita leader in the use of solar hot water with 90% of homes using this technology.[37] In the United States, Canada and Australia, heating swimming pools is the dominant application of solar hot water, with an installed capacity of 18 GW as of 2005.[38]

Heating, cooling and ventilation

Main articles: Solar heating, Thermal mass, Solar chimney, and Solar air conditioning
MIT's Solar House #1, built in 1939, used seasonal thermal storage for year-round heating.

In the United States, heating, ventilation and air conditioning (HVAC) systems account for 30% (4.65 EJ) of the energy used in commercial buildings and nearly 50% (10.1 EJ) of the energy used in residential buildings.[39][29] Solar heating, cooling and ventilation technologies can be used to offset a portion of this energy.

Thermal mass, in the most general sense, is any material that has the capacity to store heat. In the context of solar energy, thermal mass materials are used to store heat from the Sun. Common thermal mass materials include stone, cement and water. These materials have historically been used in arid climates or warm temperate regions to keep buildings cool by absorbing solar energy during the day and radiating stored heat to the cooler atmosphere at night, but they can also be used in cold temperate areas to maintain warmth. The size and placement of thermal mass should consider several factors such as climate, daylighting and shading conditions. When properly incorporated, thermal mass maintains space temperatures in a comfortable range and reduces the need for auxiliary heating and cooling equipment.[40]

A solar chimney (or thermal chimney) is a passive solar ventilation system composed of a vertical shaft connecting the interior and exterior of a building. As the chimney warms, the air inside is heated causing an updraft that pulls air through the building. Performance can be improved by using glazing and thermal mass materials in a way that mimics greenhouses. These systems have been in use since Roman times and remain common in the Middle East.[citation needed]

Deciduous trees and plants can be used to provide heating and cooling. When planted on the southern elevation of the building, the leaves can provide shade during the summer while the bare limbs allow light and warmth to pass during the winter.[41]

Desalination and disinfection

Main articles: Solar still, Solar water disinfection, and Desalination
A SODIS application in Indonesia demonstrates the simplicity of this approach to water disinfection.

Solar distillation is the production of potable water from saline or brackish water using solar energy. The first recorded use was by 16th century Arab alchemists.[42] The first large-scale solar distillation project was constructed in 1872 in the Chilean mining town of Las Salinas.[43] This 4,700 m² still could produce up to 22,700 L per day and operated for 40 years.[43] Individual still designs include single-slope, double-slope (or greenhouse type), vertical, conical, inverted absorber, multi-wick and multiple effect.[42] These stills can operate in passive, active or hybrid modes. Double slope stills are the most economical for decentralized domestic purposes while active multiple effect units are more suitable to large-scale applications.[42]

Solar water disinfection (SODIS) is a method of disinfecting water by exposing water-filled plastic PET bottles to several hours of sunlight.[44] Exposure times vary according weather and climate from a minimum of six hours to two days during fully overcast conditions.[45] SODIS is recommended by the World Health Organization as a viable method for household water treatment and safe storage.[46] Over two million people in developing countries use SODIS for their daily drinking water needs.[45]

Cooking

Main article: Solar cooker
The Solar Bowl in Auroville, India, concentrates sunlight on a movable receiver to produce steam for cooking.

Solar cookers use sunlight for cooking, drying and pasteurization. These devices can be grouped into three broad categories: box cookers, panel cookers and reflector cookers.[47] The simplest type of solar cooker is the box cooker first built by Horace de Saussure in 1767.[48] A basic box cooker consists of an insulated container with a transparent lid. These cookers can be used effectively with partially overcast skies and will typically reach temperatures of 90-150 °C.[49] Panel cookers use a reflective panel to direct sunlight onto an insulated container and reach temperatures comparable to box cookers. Reflector cookers use various concentrating geometries (dish, trough, Fresnel mirrors) to focus light on a cooking container. These cookers reach temperatures of 315 °C and above but require direct light to function properly and must be repositioned to track the Sun.[50]

The solar bowl is a unique concentrating technology employed by the Solar Kitchen in Auroville, India. The solar bowl is a stationary spherical reflector that focuses light along a line perpendicular to the sphere's interior surface and a computer control system moves the receiver to intersect this line. Steam is produced in the receiver at temperatures reaching 150 °C and then used for process heat in the kitchen.[51]

A reflector developed by Wolfgang Scheffler in 1986 is used in many solar kitchens. Scheffler reflectors are flexible parabolic dishes that combine aspects of trough and power tower concentrators. Polar tracking is used to follow the Sun's daily course and the curvature of the reflector is adjusted for seasonal variations in the incident angle of sunlight. These reflectors can reach temperatures of 450-650 °C and have a fixed focal point which improves the ease of cooking.[52] The world's largest Scheffler reflector system in Abu Road, Rajasthan, India is capable of cooking up to 35,000 meals a day.[53] As of 2008, over 2,000 large Scheffler cookers had been built worldwide.[54]

Process heat

Main articles: Solar pond, Salt evaporation pond, and Solar furnace
File:7 Meter Sheet Metal Dishes (Flipped).png
STEP parabolic dishes used for steam production and electrical generation

Concentrating solar technologies such as parabolic dish, trough and Scheffler reflectors can provide process heat for commercial and industrial applications. The first commercial system was the Solar Total Energy Project (STEP) in Shenandoah, Georgia where a field of 114 parabolic dishes provided 50% of the process heating, air conditioning and electrical requirements for a clothing factory.[55] This cogeneration system generated 400 kW of electricity and 3 MW of thermal energy in the form of steam, and had a thermal storage system that allowed for peak-load shaving.[citation needed]

Evaporation ponds are shallow pools that concentrate dissolved solids through evaporation. The use of evaporation ponds to obtain salt from sea water is one of the oldest applications of solar energy. Modern uses include concentrating brine solutions used in leach mining and removing dissolved solids from waste streams.[56]

Clothes lines, clotheshorses, and clothes racks dry clothes through evaporation. These devices use wind and sunlight instead of electricity or natural gas. Florida legislation specifically protects the 'right to dry' and similar solar rights legislation has been passed in Utah and Hawaii.[57]

Unglazed transpired collectors (UTC) are perforated sun-facing walls used for preheating ventilation air. UTCs can raise the incoming air temperature up to 22 °C and deliver outlet temperatures of 45-60 °C.[58] The short payback period of transpired collectors (3 to 12 years) makes them a more cost-effective alternative than glazed collection systems.[58] As of 2003, over 80 systems with a combined collector area of 35,000 m² had been installed worldwide, including an 860 m² collector in Costa Rica used for drying coffee beans and a 1,300 m² collector in Coimbatore, India used for drying marigolds.[23]

Solar electricity

Sunlight can be converted into electricity using photovoltaics (PV), concentrating solar power (CSP), and various experimental technologies. PV has mainly been used to power small and medium-sized applications, from the calculator powered by a single solar cell to off-grid homes powered by a photovoltaic array. For large-scale generation, CSP plants like SEGS have been the norm but recently multi-megawatt PV plants are becoming common. Completed in 2007, the 14 MW power station in Clark County, Nevada and the 20 MW site in Beneixama, Spain are characteristic of the trend toward larger photovoltaic power stations in the US and Europe.[59]

Photovoltaics

Main article: Photovoltaics
Solar cells power the International Space Station.

A solar cell (or photovoltaic cell) is a device that converts light into direct current using the photoelectric effect. The first solar cell was constructed by Charles Fritts in the 1880s.[60] Although the prototype selenium cells converted less than 1% of incident light into electricity, both Ernst Werner von Siemens and James Clerk Maxwell recognized the importance of this discovery.[61] Following the fundamental work of Russell Ohl in the 1940s, researchers Gerald Pearson, Calvin Fuller and Daryl Chapin created the silicon solar cell in 1954.[62] These early solar cells cost 286 USD/watt and reached efficiencies of 4.5-6%.[63]

The earliest significant application of solar cells was as a back-up power source to the Vanguard I satellite, which allowed the satellite to continue transmitting for over a year after its chemical battery was exhausted.[64] The successful operation of solar cells on this mission was duplicated in many other Soviet and American satellites, and by the late 1960s PV had become the established source of power for satellites.[65] Photovoltaics went on to play an essential part in the success of early commercial satellites such as Telstar and continue to remain vital to the telecommunications infrastructure today.[66]

The high cost of solar cells limited terrestrial uses throughout the 1960s. This changed in the early 1970s when prices reached levels that made PV generation competitive in remote areas without grid access. Early terrestrial uses included powering telecommunication stations, off-shore oil rigs, navigational buoys and railroad crossings.[67] These and other off-grid applications have proven very successful and accounted for over half of worldwide installed capacity until 2004.[36]

Building-integrated photovoltaics cover the roofs of an increasing number of homes.

The 1973 oil crisis stimulated a rapid rise in the production of PV during the 1970s and early 1980s.[68] Economies of scale which resulted from increasing production along with improvements in system performance brought the price of PV down from 100 USD/watt in 1971 to 7 USD/watt in 1985.[69] Steadily falling oil prices during the early 1980s led to a reduction in funding for photovoltaic R&D and a discontinuation of the tax credits associated with the Energy Tax Act of 1978. These factors moderated growth to approximately 15% per year from 1984 through 1996.[70]

Since the mid-1990s, leadership in the PV sector has shifted from the US to Japan and Germany. Between 1992 and 1994 Japan increased R&D funding, established net metering guidelines, and introduced a subsidy program to encourage the installation of residential PV systems.[71] As a result, PV installations in the country climbed from 31.2 MW in 1994 to 318 MW in 1999,[72] and worldwide production growth increased to 30% in the late 1990s.[73]

Germany has become the leading PV market worldwide since revising its Feed-in tariff system as part of the Renewable Energy Sources Act. Installed PV capacity has risen from 100 MW in 2000 to approximately 4,150 MW at the end of 2007.[74][75] Spain has become the third largest PV market after adopting a similar feed-in tariff structure in 2004, while France, Italy, South Korea and the US have also seen rapid growth recently due to various incentive programs and local market conditions.[76]

Concentrating solar power

Main article: Concentrating solar energy
File:Dish Stirling Systems of SBP in Spain.JPG
Dish engine systems eliminate the need to transfer heat to a boiler by placing a Stirling engine at the focal point.

Concentrated sunlight has been used to perform useful tasks since the time of ancient China. A legend claims Archimedes used polished shields to concentrate sunlight on the invading Roman fleet and repel them from Syracuse. In 1866, Auguste Mouchout used a parabolic trough to produce steam for the first solar steam engine, and subsequent developments led to the use of concentrating solar-powered devices for irrigation, refrigeration and locomotion.[77]

Concentrating Solar Power (CSP) systems use lenses or mirrors and tracking systems to focus a large area of sunlight into a small beam. The concentrated light is then used as a heat source for a conventional power plant. A wide range of concentrating technologies exist; the most developed are the solar trough, parabolic dish and solar power tower. These methods vary in the way they track the Sun and focus light. In all these systems a working fluid is heated by the concentrated sunlight, and is then used for power generation or energy storage.[78]

The PS10 concentrates sunlight from a field of heliostats on a central tower.

A solar trough consists of a linear parabolic reflector that concentrates light onto a receiver positioned along the reflector's focal line. The reflector is made to follow the Sun during the daylight hours by tracking along a single axis. Trough systems are the most mature CSP technology.[79] The SEGS plants in California and Acciona's Nevada Solar One near Boulder City, Nevada are representatives of this technology.[79][80]

A parabolic dish system consists of a stand-alone parabolic reflector that concentrates light onto a receiver positioned at the reflector's focal point. The reflector tracks the Sun along two axes. Parabolic dish systems give the highest efficiency among CSP technologies.[81] The 50 kW Big Dish in Canberra, Australia is an example of this technology.[79]

A solar power tower uses an array of tracking reflectors (heliostats) to concentrate light on a central receiver atop a tower. Power towers are less advanced than trough systems but offer higher efficiency and better energy storage capability.[79] The Solar Two in Barstow, California and the Planta Solar 10 in Sanlucar la Mayor, Spain are representatives of this technology.[79][82]

Experimental solar power

Main articles: Solar updraft tower, Solar pond, and Thermogenerator
An artist's depiction of a solar satellite, which could send energy wirelessly to a space vessel or planetary surface.

A solar updraft tower (also known as a solar chimney or solar tower) consists of a large greenhouse that funnels into a central tower. As sunlight shines on the greenhouse, the air inside is heated and expands. The expanding air flows toward the central tower where a turbine converts the air flow into electricity. A 50 kW prototype was constructed in Ciudad Real, Spain and operated for eight years before decommissioning in 1989.[83]

A solar pond is a pool of salt water (usually 1-2 m deep) that collects and stores solar energy. Solar ponds were first proposed by Dr. Rudolph Bloch in 1948 after he came across reports of a lake in Hungary in which the temperature increased with depth. This effect was due to salts in the lake's water, which created a "density gradient" that prevented convection currents. A prototype was constructed in 1958 on the shores of the Dead Sea near Jerusalem.[84] The pond consisted of layers of water that successively increased from a weak salt solution at the top to a high salt solution at the bottom. This solar pond was capable of producing temperatures of 90 °C in its bottom layer and had an estimated solar-to-electric efficiency of two percent.

Thermoelectric devices convert a temperature difference between dissimilar materials into an electric current. First proposed as a method to store solar energy by solar pioneer Mouchout in the 1800s,[85] thermoelectrics reemerged in the Soviet Union during the 1930s. Under the direction of Soviet scientist Abram Ioffe a concentrating system was used to thermoelectrically generate power for a 1 hp engine.[86] Thermogenerators were later used in the US space program as an energy conversion technology for powering deep space missions such as Cassini, Galileo and Viking. Research in this area is focused on raising the efficiency of these devices from 7–8% to 15–20%.[87]

Space solar power systems use a large solar array in geosynchronous orbit to collect sunlight and beam this energy in the form of microwave radiation to receivers (rectennas) on Earth for distribution. This concept was first proposed by Dr. Peter Glaser in 1968 and since then a wide variety of systems have been studied with both photovoltaic and concentrating solar thermal technologies being proposed. Although still in the concept stage, these systems offer the possibility of delivering power approximately 96% of the time.[88]

Solar chemical

Main article: Solar chemical

Solar chemical processes use solar energy to drive chemical changes. These processes offset energy that would otherwise be required from an alternate source and can convert solar energy into a storable and transportable fuel. Solar chemical reactions are diverse but can generically be described as either thermochemical or photochemical.

Hydrogen production technologies have been a significant area of solar chemical research since the 1970s. Aside from electrolysis driven by photovoltaic or photochemical cells, several thermochemical processes have also been explored. The seemingly most direct of these routes uses concentrators to split water at high temperatures (2300-2600 °C), but this process has been limited by complexity and low solar-to-hydrogen efficiency (1-2%).[89] A more conventional approach uses process heat from solar concentrators to drive the steam reformation of natural gas thereby increasing the overall hydrogen yield. Thermochemical cycles characterized by the decomposition and regeneration of reactants present another avenue of hydrogen production. The Solzinc process under development at the Weizmann Institute is one such method. This process uses a 1 MW solar furnace to decompose zinc oxide (ZnO) at temperatures above 1200 °C. This initial reaction produces pure zinc which can subsequently be reacted with water to produce hydrogen.[90]

Sandia's Sunshine to Petrol (S2P) technology uses the high temperatures generated by concentrating sunlight along with a zirconia/ferrite catalyst to break down atmospheric carbon dioxide into oxygen and carbon monoxide (CO). The CO may then be used to synthesize fuels such as methanol, gasoline and jet fuel.[91]

Photoelectrochemical cells or PECs consist of a semiconductor, typically titanium dioxide or related titanates, immersed in an electrolyte. When the semiconductor is illuminated an electrical potential develops. There are two types of photoelectrochemical cells: photoelectric cells that convert light into electricity and photochemical cells that use light to drive chemical reactions such as electrolysis.[92]

A photogalvanic device is a type of battery in which the cell solution (or equivalent) forms energy-rich chemical intermediates when illuminated. These chemical intermediates then react at the electrodes to produce an electric potential. The ferric-thionine chemical cell is an example of this technology.[93]

Solar vehicles

Main articles: Solar vehicle, Electric boat, and Solar balloon
Australia hosts the World Solar Challenge where solar cars like the Nuna3 race through a 3,021 km (1,877 mi) course from Darwin to Adelaide.

Development of a solar powered car has been an engineering goal since the 1980s. The center of this development is the World Solar Challenge, a biannual solar-powered car race in which teams from universities and enterprises compete over 3,021 kilometres (1,877 mi) across central Australia from Darwin to Adelaide. In 1987, when it was founded, the winner's average speed was 67 kilometres per hour (42 mph).[94] The 2007 race included a new challenge class using cars which could be a practical proposition for sustainable transport with little modification. The winning car averaged 90.87 kilometres per hour (56.46 mph).[citation needed] The North American Solar Challenge and the planned South African Solar Challenge are comparable competitions that reflect an international interest in the engineering and development of solar powered vehicles.[95][96]

In 1975, the first practical solar boat was constructed in England.[97] By 1995, passenger boats incorporating PV panels began appearing and are now used extensively.[98] In 1996, Kenichi Horie made the first solar powered crossing of the Pacific Ocean, and the sun21 catamaran made the first solar powered crossing of the Atlantic Ocean in the winter of 2006–2007.[99] Plans to circumnavigate the globe in 2009 are indicative of the progress solar boats have made.

Helios UAV in solar powered flight

In 1974, the unmanned Sunrise II inaugurated the era of solar flight. In 1980, the Gossamer Penguin made the first piloted flights powered solely by photovoltaics. This was quickly followed by the Solar Challenger which demonstrated a more airworthy design with its crossing of the English Channel in July 1981. Developments then turned back to unmanned aerial vehicles (UAV) with the Pathfinder (1997) and subsequent designs, culminating in the Helios which set the altitude record for a non-rocket-propelled aircraft at 29,524 metres (96,864 ft) in 2001.[100] The Zephyr, developed by BAE Systems, is the latest in a line of record-breaking solar aircraft, making a 54-hour flight in 2007, and month-long flights are envisioned by 2010.[101]

A solar balloon is a black balloon that is filled with ordinary air. As sunlight shines on the balloon, the air inside is heated and expands, causing an upward buoyancy force, much like an artificially-heated hot air balloon. Some solar balloons are large enough for human flight, but usage is limited to the toy market as the surface-area to payload-weight ratio is relatively high.[citation needed]

Solar sails are a proposed form of spacecraft propulsion using large membrane mirrors to exploit radiation pressure from the sun. Unlike rockets, solar sails require no fuel. Although the thrust is small compared to rockets, it continues as long as the Sun shines onto the deployed sail and in the frictionless vacuum of space significant speeds can eventually be achieved.[102]

Energy storage methods

Main articles: Thermal mass, Thermal energy storage, Phase change material, and Grid energy storage
Solar Two's thermal storage system allowed it to generate electricity during cloudy weather and at night.

Storage is an important issue in the development of solar energy because modern energy systems usually assume continuous availability of energy. Solar energy is not available at night, and the performance of solar power systems is affected by unpredictable weather patterns; therefore, storage media or back-up power systems must be used.

Thermal mass systems can store solar energy in the form of heat at domestically useful temperatures for daily or seasonal durations. Thermal storage systems generally use readily available materials with high specific heat capacities such as water, earth and stone. Well-designed systems can lower peak demand, shift time-of-use to off-peak hours and reduce overall heating and cooling requirements.[citation needed]

Phase change materials such as paraffin wax and Glauber's salt are another thermal storage media. These materials are inexpensive, readily available, and can deliver domestically useful temperatures (approximately 64 °C). The "Dover House" (in Dover, Massachusetts) was the first to use a Glauber's salt heating system, in 1948.[103]

Solar energy can be stored at high temperatures using molten salts. Salts are an effective storage medium because they are low-cost, have a high specific heat capacity and can deliver heat at temperatures compatible with conventional power systems. The Solar Two used this method of energy storage, allowing it to store 1.44 TJ in its 68 m³ storage tank with an annual storage efficiency of about 99%.[104]

Off-grid PV systems have traditionally used rechargeable batteries to store excess electricity. With grid-tied systems, excess electricity can be sent to the transmission grid. Net metering programs give these systems a credit for the electricity they deliver to the grid. This credit offsets electricity provided from the grid when the system cannot meet demand, effectively using the grid as a storage mechanism.[citation needed]

Pumped-storage hydroelectricity stores energy in the form of water pumped when energy is available from a lower elevation reservoir to a higher elevation one. The energy is recovered when demand is high by releasing the water to run through a hydroelectric power generator.[citation needed]

Development, deployment and economics

Main article: Deployment of solar power to energy grids
11 MW Serpa solar power plant in Portugal
File:Moody Sunburst.jpg
Solar troughs are the most widely deployed and cost-effective CSP technology.

Beginning with the surge in coal use which accompanied the Industrial Revolution, energy consumption has steadily transitioned from wood and biomass to fossil fuels. The early development of solar technologies starting in the 1860s was driven by an expectation that coal would soon become scarce, but solar development stagnated in the early 20th century in the face of the increasing availability, economy, and utility of fossil fuels such as coal and petroleum.[105]

The 1973 oil embargo and 1979 energy crisis caused a reorganization of energy policies around the world and brought renewed attention to developing solar technologies. Deployment strategies focused on incentive programs such as the Federal Photovoltaic Utilization Program in the US and the Sunshine Program in Japan. Other efforts included the formation of research facilities in the US (SERI, now NREL), Japan (NEDO), and Germany (Fraunhofer Institute for Solar Energy Systems ISE).[106]

Between 1970 and 1983, photovoltaic installations grew rapidly, but dropping oil prices in the early 1980s moderated the growth of PV from 1984 to 1996. Since 1997, PV development has accelerated due to supply issues with oil and natural gas, global warming concerns (see Kyoto Protocol), and the improving economic position of PV relative to other energy technologies. Photovoltaic production growth has averaged 40% per year since 2000 and installed capacity reached 10.6 GW at the end of 2007.[36] Since 2006 it has been economical for investors to install photovoltaics for free in return for a long term power purchase agreement. 50% of commercial systems were installed in this manner in 2007 and it is expected that 90% will by 2009.[107] Nellis Air Force Base is receiving photoelectric power for about 2.2 ¢/kWh and grid power for 9 ¢/kWh.[108][109]

Commercial solar water heaters began appearing in the United States in the 1890s.[110] These systems saw increasing use until the 1920s but were gradually replaced by cheaper and more reliable heating fuels.[111] As with photovoltaics, solar water heating attracted renewed attention as a result of the oil crises in the 1970s but interest subsided in the 1980s due to falling petroleum prices. Development in the solar water heating sector progressed steadily throughout the 1990s and growth rates have averaged 20% per year since 1999.[35] Although generally underestimated, solar water heating is by far the most widely deployed solar technology with an estimated capacity of 154 GW as of 2007.[35]

Commercial concentrating solar power (CSP) plants were first developed in the 1980s. CSP plants such as SEGS project in the United States have a LEC of 12-14 ¢/kWh.[112] The 11 MW PS10 power tower in Spain, completed in late 2005, is Europe's first commercial CSP system and a total capacity of 300 MW is expected to be installed in the same area by 2013.[113]

See also

Template:EnergyPortal

Notes

  1. ^ The volume of each cube represents the amount of energy available and consumed. The amount of solar energy available to the earth in one hour exceeds global energy demand for a year.Energy and Inspiration: Inventing the Future in Time
  2. ^ Smil (1991), p. 240
  3. ^ "Natural Forcing of the Climate System". Intergovernmental Panel on Climate Change. Retrieved 2007-09-29.
  4. ^ "Radiation Budget". NASA Langley Research Center. 2006-10-17. Retrieved 2007-09-29.
  5. ^ Somerville, Richard. "Historical Overview of Climate Change Science" (PDF). Intergovernmental Panel on Climate Change. Retrieved 2007-09-29.
  6. ^ Vermass, Wim. "An Introduction to Photosynthesis and Its Applications". Arizona State University. Retrieved 2007-09-29.
  7. ^ Scheer (2002), p. 8
  8. ^ Plambeck, James. "Energy on a Planetary Basis". University of Alberta. Retrieved 2008-05-21.
  9. ^ Smil (2006), p. 12
  10. ^ Archer, Cristina. "Evaluation of Global Wind Power". Stanford. Retrieved 2008-06-03. {{cite web}}: Unknown parameter |coauthor= ignored (|author= suggested) (help)
  11. ^ "Energy conversion by photosynthetic organisms". Food and Agriculture Organization of the United Nations. Retrieved 2008-05-25.
  12. ^ "World Total Net Electricity Consumption, 1980-2005". Energy Information Administration. Retrieved 2008-05-25.
  13. ^ "World Consumption of Primary Energy by Energy Type and Selected Country Groups, 1980-2004". Energy Information Administration. Retrieved 2008-05-17.
  14. ^ Butti and Perlin (1981), p. 15
  15. ^ "Darmstadt University of Technology solar decathlon home design". Darmstadt University of Technology. Retrieved 2008-04-25.
  16. ^ a b c Schittich (2003), p. 14
  17. ^ Butti and Perlin (1981), p. 4, 159
  18. ^ Rosenfeld, Arthur. "Painting the Town White -- and Green". Heat Island Group. Retrieved 2007-09-29. {{cite web}}: Unknown parameter |coauthors= ignored (|author= suggested) (help)
  19. ^ Jeffrey C. Silvertooth. "Row Spacing, Plant Population, and Yield Relationships". University of Arizona. Retrieved 2008-06-24.
  20. ^ Kaul (2005), p. 169–174
  21. ^ Butti and Perlin (1981), p. 42–46
  22. ^ Bénard (1981), p. 347
  23. ^ a b Leon (2006), p. 62
  24. ^ Butti and Perlin (1981), p. 19
  25. ^ Butti and Perlin (1981), p. 41
  26. ^ "Prescription Act (1872 Chapter 71 2 and 3 Will 4)". Office of the Public Sector Information. Retrieved 2008-05-18.
  27. ^ Noyes, WM (1860-03-31). "The Law of Light". The New York Times. Retrieved 2008-05-18.
  28. ^ a b Tzempelikos (2007), p. 369
  29. ^ a b Apte, J.; et al. "Future Advanced Windows for Zero-Energy Homes" (PDF). American Society of Heating, Refrigerating and Air-Conditioning Engineers. Retrieved 2008-04-09. {{cite web}}: Explicit use of et al. in: |author= (help)
  30. ^ Muhs, Jeff. "Design and Analysis of Hybrid Solar Lighting and Full-Spectrum Solar Energy Systems" (PDF). Oak Ridge National Laboratory. Retrieved 2007-09-29.
  31. ^ Myriam B.C. Aries; Guy R. Newsham (2008). "Effect of daylight saving time on lighting energy use: a literature review". Energy Policy. 36 (6): 1858–1866. doi:10.1016/j.enpol.2007.05.021.{{cite journal}}: CS1 maint: multiple names: authors list (link)
  32. ^ "Solar Energy Technologies and Applications". Canadian Renewable Energy Network. Retrieved 2007-10-22.
  33. ^ "Renewables for Heating and Cooling" (PDF). International Energy Agency. Retrieved 2008-05-26.
  34. ^ Weiss, Werner. "Solar Heat Worldwide (Markets and Contributions to the Energy Supply 2005)" (PDF). International Energy Agency. Retrieved 2008-05-30. {{cite web}}: Unknown parameter |coauthor= ignored (|author= suggested) (help)
  35. ^ a b c Weiss, Werner. "Solar Heat Worldwide - Markets and Contribution to the Energy Supply 2006" (PDF). International Energy Agency. Retrieved 2008-06-09. {{cite web}}: Unknown parameter |coauthor= ignored (|author= suggested) (help)
  36. ^ a b c "Renewables 2007 Global Status Report" (PDF). Worldwatch Institute. Retrieved 2008-04-30.
  37. ^ Del Chiaro, Bernadette. "Solar Water Heating (How California Can Reduce Its Dependence on Natural Gas)" (PDF). Environment California Research and Policy Center. Retrieved 2007-09-29. {{cite web}}: Unknown parameter |coauthor= ignored (|author= suggested) (help)
  38. ^ Philibert, Cédric. "The Present and Future use of Solar Thermal Energy as a Primary Source of Energy" (PDF). International Energy Agency. Retrieved 2008-05-05.
  39. ^ "Energy Consumption Characteristics of Commercial Building HVAC Systems Volume III: Energy Savings Potential" (PDF). United States Department of Energy. pp. 2–2. Retrieved 2008-06-24.
  40. ^ Mazria(1979), p. 29–35
  41. ^ Mazria(1979), p. 255
  42. ^ a b c Tiwari (2003), p. 368–371
  43. ^ a b Daniels (1964), p. 6
  44. ^ "SODIS solar water disinfection". EAWAG (The Swiss Federal Institute for Environmental Science and Technology). Retrieved 2008-05-02.
  45. ^ a b "Household Water Treatment Options in Developing Countries: Solar Disinfection (SODIS)" (PDF). Centers for Disease Control and Prevention. Retrieved 2008-05-13.
  46. ^ "Household Water Treatment and Safe Storage". World Health Organization. Retrieved 2008-05-02.
  47. ^ Anderson and Palkovic (1994), p. xi
  48. ^ Butti and Perlin (1981), p. 54–59
  49. ^ Anderson and Palkovic (1994), p. xii
  50. ^ Anderson and Palkovic (1994), p. xiii
  51. ^ "The Solar Bowl". Auroville Universal Township. Retrieved 2008-04-25.
  52. ^ "Scheffler-Reflector". Solare Bruecke. Retrieved 2008-04-25.
  53. ^ "Solar Steam Cooking System". Gadhia Solar. Retrieved 2008-04-25.
  54. ^ "Scheffler Reflector". Solare Bruecke. Retrieved 2008-07-03.
  55. ^ Poche, A. "Solar total energy project at Shenandoah, Georgia system design". SAO/NASA ADS Physics Abstract Service. Retrieved 2008-05-20.
  56. ^ Bartlett (1998), p.393–394
  57. ^ Thomson-Philbrook, Julia. "Right to Dry Legislation in New England and Other States". Connecticut General Assembly. Retrieved 2008-05-27.
  58. ^ a b "Solar Buildings (Transpired Air Collectors - Ventilation Preheating)" (PDF). National Renewable Energy Laboratory. Retrieved 2007-09-29.
  59. ^ "Large-scale photovoltaic power plants". pvresources. Retrieved 2008-06-27.
  60. ^ Perlin (1999), p. 147
  61. ^ Perlin (1999), p. 18–20
  62. ^ Perlin (1999), p. 29
  63. ^ Perlin (1999), p. 29–30, 38
  64. ^ Perlin (1999), p. 45–46
  65. ^ Perlin (1999), p. 49–50
  66. ^ Perlin (1999), p. 49–50, 190
  67. ^ Perlin (1999), p. 57–85
  68. ^ "Photovoltaic Milestones". Energy Information Agency - Department of Energy. Retrieved 2008-05-20.
  69. ^ Perlin (1999), p. 50, 118
  70. ^ "World Photovoltaic Annual Production, 1971-2003". Earth Policy Institute. Retrieved 2008-05-29.
  71. ^ "Policies to Promote Non-hydro Renewable Energy in the United States and Selected Countries" (PDF). Energy Information Agency - Department of Energy. Retrieved 2008-05-29.
  72. ^ Foster, Robert. "Japan Pholtovoltaics Market Overview" (PDF). Department of Energy. Retrieved 2008-06-05.
  73. ^ Handleman, Clayton. "An Experience Curve Based Model for the Projection of PV Module Costs and Its Policy Implications" (PDF). Heliotronic. Retrieved 2008-05-29.
  74. ^ "Renewable energy sources in figures - national and international development" (PDF). Federal Ministry for the Environment, Nature Conservation and Nuclear Safety (Germany). Retrieved 2008-05-29.
  75. ^ "Marketbuzz 2008: Annual World Solar Pholtovoltaic Industry Report". solarbuzz. Retrieved 2008-06-05.
  76. ^ "Trends in Photovoltaic Applications - Survey report of selected IEA countries between 1992 and 2006" (PDF). International Energy Agency. Retrieved 2008-06-05.
  77. ^ Butti and Perlin (1981), p. 60–100
  78. ^ Martin and Goswami (2005), p. 45
  79. ^ a b c d e "Concentrating Solar Power in 2001 - An IEA/SolarPACES Summary of Present Status and Future Prospects" (PDF). International Energy Agency - SolarPACES. Retrieved 2008-07-02.
  80. ^ "UNLV Solar Site". University of Las Vegas. Retrieved 2008-07-02.
  81. ^ "An Assessment of Solar Energy Conversion Technologies and Research Opportunities" (PDF). Stanford University - Global Climate Change & Energy Project. Retrieved 2008-07-02.
  82. ^ David Shukman. "Power station harnesses Sun's rays". BBC News. Retrieved 2008-07-02.
  83. ^ Mills (2004), p. 19–31
  84. ^ Halacy (1973), p. 181
  85. ^ Perlin and Butti (1981), p. 73
  86. ^ Halacy (1973), p. 76
  87. ^ Tritt (2008), p. 366–368
  88. ^ "Space Solar Power Satellite Technology Development at the Glenn Research Center — An Overview" (PDF). National Aeronautics and Space Administration. Retrieved 2008-06-27.
  89. ^ Agrafiotis (2005), p. 409
  90. ^ "Solar Energy Project at the Weizmann Institute Promises to Advance the use of Hydrogen Fuel". Weizmann Institute of Science. Retrieved 2008-06-25.
  91. ^ "Sandia's Sunshine to Petrol project seeks fuel from thin air". Sandia Corporation. Retrieved 2008-05-02.
  92. ^ Bolton (1977), p. 11
  93. ^ Bolton (1977), p. 16, 119
  94. ^ "World Solar Challenge History". Electrick Publications and NJK. Retrieved 2008-06-24.
  95. ^ "North American Solar Challenge". New Resources Group. Retrieved 2008-07-03.
  96. ^ "South African Solar Challenge". Advanced Energy Foundation. Retrieved 2008-07-03.
  97. ^ Electrical Review Vol 201 No 7 12 August 1977
  98. ^ Schmidt, Theodor. "Solar Ships for the new Millennium". TO Engineering. Retrieved 2007-09-30.
  99. ^ "The sun21 completes the first transatlantic crossing with a solar powered boat". Transatlantic 21. Retrieved 2007-09-30.
  100. ^ "Solar-Power Research and Dryden". NASA. Retrieved 2008-04-30.
  101. ^ "The NASA ERAST HALE UAV Program". Greg Goebel. Retrieved 2008-04-30.
  102. ^ "Solar Sails Could Send Spacecraft 'Sailing' Through Space". National Aeronautics and Space Administration. Retrieved 2007-11-26.
  103. ^ Butti and Perlin (1981), p. 212–214
  104. ^ "Advantages of Using Molten Salt". Sandia National Laboratory. Retrieved 2007-09-29.
  105. ^ Butti and Perlin (1981), p. 63, 77, 101
  106. ^ "Chronicle of Fraunhofer-Gesellschaft". Fraunhofer-Gesellschaft. Retrieved 2007-11-04.
  107. ^ Solar Power Services: How PPAs are Changing the PV Value Chain
  108. ^ Nellis Solar Power System
  109. ^ "Supporting Solar Photovoltaic Electricity - An Argument for Feed-in Tariffs" (PDF). European Photovoltaic Industry Association. Retrieved 2008-06-09.
  110. ^ Butti and Perlin (1981), p. 117
  111. ^ Butti and Perlin (1981), p. 139
  112. ^ "DOE Concentrating Solar Power 2007 Funding Opportunity Project Prospectus" (PDF). Department of Energy. Retrieved 2008-06-12.
  113. ^ "PS10". SolarPACES (Solar Power and Chemical Energy Systems). Retrieved 2008-06-24.

References

  • Agrafiotis, C.; Roeb, M.; Konstandopoulos, A.G.; Nalbandian, L.; Zaspalis, V.T.; Sattler, C.; Stobbe, P.; Steele, A.M. (2005). "Solar water splitting for hydrogen production with monolithic reactors". Solar Energy. 79 (4): 409–421. doi:10.1016/j.solener.2005.02.026.
  • Anderson, Lorraine (1994). Cooking with Sunshine (The Complete Guide to Solar Cuisine with 150 Easy Sun-Cooked Recipes). Marlowe & Company. ISBN 156924300X. {{cite book}}: Unknown parameter |coauthor= ignored (|author= suggested) (help)
  • Bénard, C.; Gobin, D.; Gutierrez, M. (1981). "Experimental Results of a Latent-Heat Solar-Roof, Used for Breeding Chickens". Solar Energy. 26 (4): 347–359. doi:10.1016/0038-092X(81)90181-X.
  • Bolton, James (1977). Solar Power and Fuels. Academic Press, Inc. ISBN 0121123502.
  • Butti, Ken (1981). A Golden Thread (2500 Years of Solar Architecture and Technology). Van Nostrand Reinhold. ISBN 0442240058. {{cite book}}: Unknown parameter |coauthor= ignored (|author= suggested) (help)
  • Daniels, Farrington (1964). Direct Use of the Sun's Energy. Ballantine Books. ISBN 0345259386.
  • Halacy, Daniel (1973). The Coming Age of Solar Energy. Harper and Row. ISBN 0380002337.
  • Hunt, V. Daniel (1979). Energy Dictionary. Van Nostrand Reinhold Company. ISBN 0442273959.
  • Karan, Kaul; Greer, Edith; Kasperbauer, Michael; Mahl, Catherine (2001). "Row Orientation Affects Fruit Yield in Field-Grown Okra". Journal of Sustainable Agriculture. 17 (2/3): 169–174. doi:10.1300/J064v17n02_14.
  • Leon, M.; Kumar, S. (2007). "Mathematical modeling and thermal performance analysis of unglazed transpired solar collectors". Solar Energy. 81 (1): 62–75. doi:10.1016/j.solener.2006.06.017.
  • Lieth, Helmut (1975). Primary Productivity of the Biosphere. Springer-Verlag1. ISBN 0387070834. {{cite book}}: Unknown parameter |coauthors= ignored (|author= suggested) (help)
  • Martin, Christopher L. (2005). Solar Energy Pocket Reference. International Solar Energy Society. ISBN 0977128202. {{cite book}}: Unknown parameter |coauthors= ignored (|author= suggested) (help)
  • Mazria, Edward (1979). The Passive Solar Energy Book. Rondale Press. ISBN 0878572384.
  • Meier, Anton; Bonaldi, Enrico; Cella, Gian Mario; Lipinski, Wojciech; Wuillemin, Daniel (2005). "Solar chemical reactor technology for industrial production of lime". Solar Energy. 80 (10): 1355–1362. doi:10.1016/j.solener.2005.05.017.
  • Mills, David (2004). "Advances in solar thermal electricity technology". Solar Energy. 76 (1–3): 19–31. doi:10.1016/S0038-092X(03)00102-6.
  • Müller, Reto; Steinfeld, A. (2007). "Band-approximated radiative heat transfer analysis of a solar chemical reactor for the thermal dissociation of zinc oxide". Solar Energy. 81 (10): 1285–1294. doi:10.1016/j.solener.2006.12.006.
  • Perlin, John (1999). From Space to Earth (The Story of Solar Electricity). Harvard University Press. ISBN 0674010132.
  • Bartlett, Robert (1998). Solution Mining: Leaching and Fluid Recovery of Materials. Routledge. ISBN 9056996339.
  • Scheer, Hermann (2002). The Solar Economy (Renewable Energy for a Sustainable Global Future). Earthscan Publications Ltd. ISBN 1844070751.
  • Schittich, Christian (2003). Solar Architecture (Strategies Visions Concepts). Architektur-Dokumentation GmbH & Co. KG. ISBN 3764307471.
  • Smil, Vaclav (1991). General Energetics: Energy in the Biosphere and Civilization. Wiley. p. 369. ISBN 0471629057.
  • Smil, Vaclav (2003). Energy at the Crossroads: Global Perspectives and Uncertainties. MIT Press. p. 443. ISBN 0262194929.
  • Smil, Vaclav (2006-05-17). Energy at the Crossroads (PDF). Organisation for Economic Co-operation and Development. ISBN 0262194929. Retrieved 2007-09-29.
  • Tabor, H. Z.; Doron, B. (1990). "The Beith Ha'Arava 5 MW(e) Solar Pond Power Plant (SPPP)--Progress Report". Solar Energy. 45 (4): 247–253. doi:10.1016/0038-092X(90)90093-R.
  • Tiwari, G. N.; Singh, H. N.; Tripathi, R. (2003). "Present status of solar distillation". Solar Energy. 75 (5): 367–373. doi:10.1016/j.solener.2003.07.005.
  • Tritt, T.; Böttner, H.; Chen, L. (2008). "Thermoelectrics: Direct Solar Thermal Energy Conversion". MRS Bulletin. 33 (4): 355–372.
  • Tzempelikos, Athanassios; Athienitis, Andreas K. (2007). "The impact of shading design and control on building cooling and lighting demand". Solar Energy. 81 (3): 369–382. doi:10.1016/j.solener.2006.06.015.
  • Vecchia, A.; Formisano, W.; Rosselli, V; Ruggi, D. (1981). "Possibilities for the Application of Solar Energy in the European Community Agriculture". Solar Energy. 26 (6): 479–489. doi:10.1016/0038-092X(81)90158-4.

External links

Wikimedia Commons has media related to Solar energy.

Template:Navbox/Solar energy

Retrieved from "https://en.wikipedia.org/w/index.php?title=Solar_energy&oldid=224294558"