List of ISO standards 1–1999

{h ISO 9427]

• ISO 3806:1977 Plywood — Determination of moisture content [Withdrawn: replaced with ISO 9425]
• ISO 3807:2013 Gas cylinders — Acetylene cylinders — Basic requirements and type testing
• ISO 3808:2002 Road vehicles — Unscreened high-voltage ignition cables — General specifications, test methods and requirements
• ISO 3809:2004 Oil of lime (cold pressed), Mexican type (Citrus aurantifolia (Christm.) Swingle), obtained by mechanical means
• ISO 3810:1987 Floor tiles of agglomerated cork — Methods of test
• ISO 3811:1979 Meat and meat products — Detection and enumeration of presumptive coliform bacteria and presumptive Escherichia coli — (Reference method) [Withdrawn: replaced with ISO 4831, ISO 4832, and ISO 7251]
• ISO 3812:1976 Essential oils of geranium and rose — Determination of ester value after hot formylation
• ISO 3813:2004 Resilient floor coverings — Cork floor tiles — Specification
• ISO/TS 3814:2014 Standard tests for measuring reaction-to-fire of products and materials — Their development and application
• ISO 3815 Zinc and zinc alloys
  • ISO 3815-1:2005 Part 1: Analysis of solid samples by optical emission spectrometry
  • ISO 3815-2:2005 Part 2: Analysis by inductively coupled plasma optical emission spectrometry
• ISO 3816:1976 Zinc ingots — Selection and preparation of samples for spectrographic analysis [Withdrawn: replaced with ISO 20081]
• ISO 3817:1976 Zinc alloy ingots — Selection and preparation of samples for spectrographic analysis [Withdrawn: replaced with ISO 20081]
• ISO/TR 3818:1977 Ropes and cordage — Rope assemblies used in slinging — Safe working loads [Withdrawn without replacement]
• ISO 3819:2015 Laboratory glassware – Beakers
• ISO 3820:1978 Cinematography — Sprockets for 8 mm Type S motion-picture film — Dimensions and design
• ISO 3821:2019 Gas welding equipment — Rubber hoses for welding, cutting and allied processes
• ISO 3822 Acoustics – Laboratory tests on noise emission from appliances and equipment used in water supply installations
  • ISO 3822-1:1999 Part 1: Method of measurement
  • ISO 3822-2:1995 Part 2: Mounting and operating conditions for draw-off taps and mixing valves
  • ISO 3822-3:2018 Part 3: Mounting and operating conditions for in-line valves and appliances
  • ISO 3822-4:1997 Part 4: Mounting and operating conditions for special appliances
• ISO 3823 Dental rotary instruments — Burs
  • ISO 3823-1:1997 Part 1: Steel and carbide burs
  • ISO 3823-2:2003 Part 2: Finishing burs
• ISO 3824:1984 Dental silicophosphate cement (hand-mixed) [Withdrawn: replaced with ISO 9917]
• ISO 3825:1977 Glass transfusion bottles for medical use — Chemical resistance [Withdrawn without replacement]
• ISO 3826 Plastics collapsible containers for human blood and blood components
  • ISO 3826-1:2013 Part 1: Conventional containers
  • ISO 3826-2:2008 Part 2: Graphical symbols for use on labels and instruction leaflets
  • ISO 3826-3:2006 Part 3: Blood bag systems with integrated features
  • ISO 3826-4:2015 Part 4: Aphaeresis blood bag systems with integrated features
• ISO 3827 Shipbuilding — Co-ordination of dimensions in ships' accommodation
  • ISO 3827-1:1977 Part 1: Principles of dimensional co-ordination
  • ISO 3827-2:1977 Part 2: Glossary of terms
  • ISO 3827-3:1977 Part 3: Co-ordinating sizes for components and assemblies
  • ISO 3827-4:1977 Part 4: Controlling dimensions
  • ISO 3827-5:1979 Part 5: Co-ordinating sizes for key components
• ISO 3828:2008 Shipbuilding and marine structures – Deck machinery – Vocabulary and symbols
• ISO 3829 Petroleum products – Determination of density and relative density – Jaulmes pyknometer method [Rejected draft]
• ISO 3830:1993 Petroleum products — Determination of lead content of gasoline — Iodine monochloride method
• ISO 3831:1979 Timekeeping instruments — Classification and numbering system and nomenclature of components for watches and clocks [Withdrawn without replacement]
• ISO 3832:2002 Passenger cars — Luggage compartments — Method of measuring reference volume
• ISO 3833:1977 Road vehicles – Types – Terms and definitions
• ISO 3834 Quality requirements for fusion welding of metallic materials
  • ISO 3834-1:2021 Part 1: Criteria for the selection of the appropriate level of quality requirements
  • ISO 3834-2:2021 Part 2: Comprehensive quality requirements
  • ISO 3834-3:2021 Part 3: Standard quality requirements
  • ISO 3834-4:2021 Part 4: Elementary quality requirements
  • ISO 3834-5:2021 Part 5: Documents with which it is necessary to conform to claim conformity to the quality requirements of ISO 3834-2, ISO 3834-3 or ISO 3834-4
• ISO 3835 Equipment for vine cultivation and wine making – Vocabulary
  • ISO 3835-1:1976 (No part title)
  • ISO 3835-2:1977 (No part title) [Withdrawn without replacement]
  • ISO 3835-3:1980 (No part title)
  • ISO 3835-4:1981 (No part title)
  • ISO 3835-5:1982 (No part title) [Withdrawn without replacement]
• ISO/TR 3836:1978 Shoe sizes — System of width grading (for use in the Mondopoint system) [Withdrawn without replacement]
• ISO 3837:1993 Liquid petroleum products — Determination of hydrocarbon types — Fluorescent indicator adsorption method
• ISO 3838:2004 Crude petroleum and liquid or solid petroleum products — Determination of density or relative density — Capillary-stoppered pyknometer and graduated bicapillary pyknometer methods
• ISO 3839:1996 Petroleum products — Determination of bromine number of distillates and aliphatic olefins — Electrometric method
• ISO 3840:1976 Petroleum distillates — Determination of olefinic plus aromatic hydrocarbons content [Withdrawn without replacement]
• ISO 3841:1977 Petroleum waxes — Determination of melting point (cooling curve) [Withdrawn without replacement]
• ISO 3842:2006 Road vehicles — Fifth wheels — Interchangeability
• ISO 3843 Anodizing of aluminium and its alloys — Accelerated test of light fastness of coloured anodic oxidation coatings using artificial light [Draft named ISO 2135 as it was a revision of ISO/R 2135]
• ISO 3844:1975 Shoe sizes — Method of marking [Withdrawn: replaced with ISO 9407]
• ISO 3845 Petroleum and natural gas industries — High-test steel line pipe [Rejected draft]
• ISO 3846:2008 Hydrometry – Open channel flow measurement using rectangular broad-crested weirs
• ISO 3847:1977 Liquid flow measurement in open channels by weirs and flumes – End-depth method for estimation of flow in rectangular channels with a free overfall [Withdrawn: replaced with ISO 18481]
• ISO 3848:2016 Essential oil of citronella, Java type
• ISO 3849:2003 Oil of citronella, Sri Lankan type (Cymbopogon nardus (L.) W. Watson var. lenabatu Stapf.)
• ISO 3850:2004 Resilient floor coverings – Determination of apparent density of composition cork
• ISO 3851:1977 Capsulated dental silicate and silico-phosphate filling materials [Withdrawn: replaced with ISO 9917]
• ISO 3852:2007 Iron ores for blast furnace and direct reduction feedstocks — Determination of bulk density
• ISO 3853:1994 Road vehicles — Towing vehicle coupling device to tow caravans or light trailers — Mechanical strength test
• ISO 3854:1976 Road vehicles — Caravans and light trailers — Vacuum braking — Measurement of reaction time [Withdrawn without replacement]
• ISO 3855:1977 Milling cutters – Nomenclature
• ISO 3856 Paints and varnishes — Determination of "soluble" metal content
  • ISO 3856-1:1984 Part 1: Determination of lead content — Flame atomic absorption spectrometric method and dithizone spectrophotometric method
  • ISO 3856-2:1984 Part 2: Determination of antimony content — Flame atomic absorption spectrometric method and Rhodamine B spectrophotometric method
  • ISO 3856-3:1984 Part 3: Determination of barium content — Flame atomic emission spectrometric method
  • ISO 3856-4:1984 Part 4: Determination of cadmium content — Flame atomic absorption spectrometric method and polarographic method
  • ISO 3856-5:1984 Part 5: Determination of hexavalent chromium content of the pigment portion of the liquid paint or the paint in powder form — Diphenylcarbazide spectrophotometric method
  • ISO 3856-6:1984 Part 6: Determination of total chromium content of the liquid portion of the paint — Flame atomic absorption spectrometric method
  • ISO 3856-7:1984 Part 7: Determination of mercury content of the pigment portion of the paint and of the liquid portion of water-dilutable paints — Flameless atomic absorption spectrometric method
• ISO 3857 Compressors, pneumatic tools and machines – Vocabulary
  • ISO 3857-1:1977 Part 1: General
  • ISO 3857-2:1977 Part 2: Compressors
  • ISO 3857-3:1989 Part 3: Pneumatic tools and machines
  • ISO 3857-4:2012 Part 4: Air treatment
• ISO 3858:2018 Rubber compounding ingredients — Carbon black — Determination of light transmittance of toluene extract
• ISO 3859:2000 Inverse dovetail cutters and dovetail cutters with cylindrical shanks
• ISO 3860:2011 Bore cutters with key drive — Form milling cutters with constant profile
• ISO 3861:2005 Rubber hoses and hose assemblies for sand and grit blasting — Specification
• ISO 3862:2020 Rubber hoses and hose assemblies — Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids — Specification
• ISO 3863:1989 Cylindrical cork stoppers — Dimensional characteristics, sampling, packaging and marking [Withdrawn without replacement]
• ISO 3864 Graphical symbols – Safety colours and safety signs
• ISO 3865:2020 Rubber, vulcanized or thermoplastic — Methods of test for staining in contact with organic material
• ISO 3866:1977 Office machines and printing machines used for information processing – Widths of fabric printing ribbons on spools exceeding 19 mm
• ISO 3867:2017 Composition cork — Expansion joint fillers — Test methods
• ISO 3868:1976 Metallic and other non-organic coatings — Measurement of coating thicknesses — Fizeau multiple-beam interferometry method
• ISO 3869:2017 Agglomerated cork — Expansion joint fillers — Specifications, packaging and marking
• ISO 3870:1976 Conveyor belts (fabric carcass), with length between pulley centres up to 300 m, for loose bulk materials — Adjustment of take-up device [Withdrawn without replacement]
• ISO 3871:2000 Road vehicles — Labelling of containers for petroleum-based or non-petroleum-based brake fluid
• ISO 3872:1976 Graphic technology — Sheet-fed printing machines — Range of sizes [Withdrawn without replacement]
• ISO 3873:1977 Industrial safety helmets
• ISO 3874:2017 Series 1 freight containers — Handling and securing
• ISO 3875:2020 Machine tools — Test conditions for external cylindrical centreless grinding machines — Testing of the accuracy
• ISO 3876:1986 Shipbuilding — Inland vessels — Hand-holes
• ISO 3877 Tyres, valves and tubes – List of equivalent terms
  • ISO 3877-1:1997 Part 1: Tyres
  • ISO 3877-2:1997 Part 2: Tyre valves
  • ISO 3877-3:1978 Part 3: Tubes
  • ISO 3877-4:1984 Part 4: Solid tyres
• ISO 3878:1983 Hardmetals — Vickers hardness test [Withdrawn without replacement]
• ISO 3879:1977 Welded joints — Recommended practice for liquid penetrant testing [Withdrawn: replaced with ISO 3452]
• ISO 3880 Building construction – Stairs – Vocabulary
  • ISO 3880-1:1977 [Withdrawn without replacement]
• ISO 3881:1977 Building construction — Modular co-ordination — Stairs and stair openings — Co-ordinating dimensions
• ISO 3882:2003 Metallic and other inorganic coatings — Review of methods of measurement of thickness
• ISO 3883:1977 Office machines – Line and character capacity of address masters
• ISO/DIS 3884:1975 Plastic
• ISO 3886:1986 Iron ores — Determination of manganese content — Periodate spectrophotometric method [Withdrawn: replaced with ISO 9682-2]
• ISO 3887:2007 Steels — Determination of the depth of decarburization
• ISO 3888 Passenger cars — Test track for a severe lane-change manoeuvre
  • ISO 3888-1:2018 Part 1: Double lane-change
  • ISO 3888-2:2011 Part 2: Obstacle avoidance
• ISO 3889:2006 Milk and milk products — Specification of Mojonnier-type fat extraction flasks
• ISO 3890 Milk and milk products — Determination of residues of organochlorine compounds (pesticides)
  • ISO 3890-1:2009 Part 1: General considerations and extraction methods
  • ISO 3890-2:2009 Part 2: Test methods for crude extract purification and confirmation
• ISO 3891:1978 Acoustics — Procedure for describing aircraft noise heard on the ground [Withdrawn without replacement]
• ISO 3892:2000 Conversion coatings on metallic materials — Determination of coating mass per unit area — Gravimetric methods
• ISO 3893:1977 Concrete — Classification by compressive strength [Withdrawn without replacement]
• ISO 3894:2015 Road vehicles — Wheels/rims for commercial vehicles — Test methods
• ISO 3895:1986 Road vehicles — Screened and waterproof spark-plug and its connection — Type 2
• ISO 3896:1986 Road vehicles — Screened and waterproof spark-plug and its connection — Type 3
• ISO 3897:1997 Photography — Processed photographic plates — Storage practices [Withdrawn: replaced with ISO 18918]
• ISO 3898:2013 Bases for design of structures — Names and symbols of physical quantities and generic quantities
• ISO 3899:2005 Rubber — Nitrile latex — Determination of residual acrylonitrile content
• ISO 3900:1995 Rubber — Nitrile latex — Determination of bound acrylonitrile content
• ISO 3901:2019 Information and documentation – International Standard Recording Code (ISRC)
• ISO 3902:1990 Shipbuilding and marine structures — Gaskets for rectangular windows and side scuttles
• ISO 3903:2012 Ships and marine technology — Ships' ordinary rectangular windows
• ISO 3904:1990 Shipbuilding and marine structures — Clear-view screens
• ISO 3905:1980 Paints and varnishes — Determination of contrast ratio (opacity) of light coloured paints at a fixed spreading rate (using black and white charts) [Withdrawn: replaced with ISO 6504-3]
• ISO 3906:1980 Paints and varnishes — Determination of contrast ratio (opacity) of light coloured paints at a fixed spreading rate (using polyester film) [Withdrawn: replaced with ISO 6504-3]
• ISO 3907:2009 Hardmetals — Determination of total carbon — Gravimetric method
• ISO 3908:2009 Hardmetals — Determination of insoluble (free) carbon — Gravimetric method
• ISO 3909:1976 Hardmetals — Determination of cobalt — Potentiometric method
• ISO 3910:1983 Rubber boots, unlined moulded [Withdrawn without replacement]
• ISO 3911:2021 Wheels and rims for pneumatic tyres – Vocabulary, designation and marking
• ISO 3912:1977 Woodruff keys and keyways [Withdrawn without replacement]
• ISO 3913:1977 Shipbuilding — Welded steel bollards
• ISO 3914 Textile machinery and accessories — Cylindrical tubes
  • ISO 3914-1:1994 Part 1: Recommended main dimensions
  • ISO 3914-2:1994 Part 2: Dimensions, tolerances and designation of tubes for open-end spinning machines
  • ISO 3914-3:1994 Part 3: Dimensions, tolerances and designation of tubes for tape yarns
  • ISO 3914-4:1994 Part 4: Dimensions, tolerances and designation of tubes for textured yarns [Withdrawn without replacement]
  • ISO 3914-5:1994 Part 5: Dimensions, tolerances and designation of tubes for continuous spin-drawn synthetic filament yarns [Withdrawn without replacement]
  • ISO 3914-6:1994 Part 6: Dimensions, tolerances and designation of tubes for cross-wound packages in winding and twisting [Withdrawn without replacement]
  • ISO 3914-7:1994 Part 7: Dimensions, tolerances and designation of perforated tubes for cheese dyeing
• ISO 3915:2022 Plastics — Measurement of resistivity of conductive plastics
• ISO 3916:1977 Shipbuilding — Inland navigation — Rope tubs [Withdrawn without replacement]
• ISO 3917:2016 Road vehicles — Safety glazing materials — Test methods for resistance to radiation, high temperature, humidity, fire and simulated weathering
• ISO 3918:2007 Milking machine installations – Vocabulary
• ISO 3919:2005 Coated abrasives — Flap wheels with shaft
• ISO 3920:1976 Honing stones of square section — Designation and dimensions [Withdrawn: replaced with ISO 603-(1-16)]
• ISO 3921:1976 Honing stones of rectangular section — Designation and dimensions [Withdrawn: replaced with ISO 603-(1-16)]
• ISO 3922:1978 Continuous mechanical handling equipment — Rotary vane feeder — Dimensional specifications [Withdrawn without replacement]
• ISO 3923 Metallic powders — Determination of apparent density
  • ISO 3923-1:2018 Part 1: Funnel method
  • ISO 3923-2:1981 Part 2: Scott volumeter method
  • ISO 3923-3:1986 Part 3: Oscillating funnel method [Withdrawn without replacement]
• ISO 3924:2019 Petroleum products — Determination of boiling range distribution — Gas chromatography method
• ISO 3925:2014 Unsealed radioactive substances — Identification and documentation
• ISO 3926:1980 Shipbuilding — Inland navigation — Couplings for oil and fuel reception — Mating dimensions
• ISO 3927:2017 Metallic powders, excluding powders for hardmetals — Determination of compressibility in uniaxial compression
• ISO 3928:2016 Sintered metal materials, excluding hardmetals — Fatigue test pieces
• ISO 3929:2003 Road vehicles — Measurement methods for exhaust gas emissions during inspection or maintenance
• ISO 3930:2000 Instruments for measuring vehicle exhaust emissions [Withdrawn without replacement]
• ISO 3931 Fibre building boards – Determination of transversal internal bond [Rejected draft]
• ISO 3932:1976 Textiles — Woven fabrics — Measurement of width of pieces [Withdrawn: replaced with ISO 22198]
• ISO 3933:1976 Textiles — Woven fabrics — Measurement of length of pieces [Withdrawn: replaced with ISO 22198]
• ISO 3934:2021 Rubber, vulcanized and thermoplastic — Preformed gaskets used in buildings — Classification, specifications and test methods
• ISO 3935:1977 Shipbuilding — Inland navigation — Fire-fighting water system — Pressures [Withdrawn without replacement]
• ISO 3936:1993 Reduction sleeves with tenon drive with external and internal 7/24 taper — Dimensions
• ISO 3937 Cutter arbors with tenon drive
  • ISO 3937-1:2008 Part 1: Dimensions of Morse taper
  • ISO 3937-2:2008 Part 2: Dimensions of 7/24 taper
  • ISO 3937-3:2008 Part 3: Dimensions of hollow taper interface with flange contact surface
• ISO 3938:1986 Hydraulic fluid power — Contamination analysis — Method for reporting analysis data [Withdrawn without replacement]
• ISO 3939:1977 Fluid power systems and components — Multiple lip packing sets — Methods for measuring stack heights
• ISO 3940:1977 Tapered die-sinking cutters with parallel shanks
• ISO 3941:1977 Classification of fires
• ISO 3942:1976 Photographic grade sodium carbonate, monohydrate — Specification [Withdrawn: replaced with ISO 424]
• ISO 3943:1993 Photography — Processing chemicals — Specifications for anhydrous sodium acetate
• ISO 3944:1992 Fertilizers — Determination of bulk density (loose)
• ISO 3945:1985 Mechanical vibration of large rotating machines with speed range from 10 to 200 r/s — Measurement and evaluation of vibration severity in situ [Withdrawn: replaced with ISO 10816-1]
• ISO 3946:1982 Starches and derived products — Determination of total phosphorus content — Spectrophotometric method
• ISO 3947:1977 Starches, native or modified — Determination of total fat content
• ISO 3948:1977 Shipbuilding — Inland vessels — Compressed-air systems — Pressure ranges
• ISO 3949:2020 Plastics hoses and hose assemblies — Textile-reinforced types for hydraulic applications — Specification
• ISO 3950:2016 Dentistry – Designation system for teeth and areas of the oral cavity
• ISO 3951 Sampling procedures for inspection by variables
  • ISO 3951-1:2013 Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL
  • ISO 3951-2:2013 Part 2: General specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics
  • ISO 3951-3:2007 Part 3: Double sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
  • ISO 3951-4:2011 Part 4: Procedures for assessment of declared quality levels
  • ISO 3951-5:2006 Part 5: Sequential sampling plans indexed by acceptance quality limit (AQL) for inspection by variables (known standard deviation)
• ISO 3952 Kinematic diagrams – Graphical symbols
  • ISO 3952-1:1981 (Motion of links of mechanisms; Kinematic pairs; Links and connections of their components; Linkage of bars and their links)
  • ISO 3952-2:1981 (Friction and gear mechanisms; Cam mechanisms)
  • ISO 3952-3:1979 (Maltese and ratchet mechanisms; Couplings and brakes)
  • ISO 3952-4:1984 (Miscellaneous mechanisms and their components)
• ISO 3953:2011 Metallic powders — Determination of tap density
• ISO 3954:2007 Powders for powder metallurgical purposes — Sampling
• ISO 3955:1977 Sintered metal materials, excluding hardmetals — Sampling [Withdrawn without replacement]
• ISO/TR 3956:1975 Principles of structural fire-engineering design with special regard to the connection between real fire exposure and the heating conditions of the standard fire-resistance test (ISO 834)
• ISO 3957 Reaction to fire tests — Façades — Measurement of heat and smoke generation in severe exterior fire scenarios [Under development; originally planned ISO 3957 Graphic symbols — Index, survey, and compilation of the single sheets became ISO 7000]
• ISO 3958:1996 Passenger cars — Driver hand-control reach
• ISO 3959:1977 Green bananas — Ripening conditions
• ISO 3960:2017 Animal and vegetable fats and oils — Determination of peroxide value — Iodometric (visual) endpoint determination
• ISO 3961:2018 Animal and vegetable fats and oils — Determination of iodine value
• ISO 3962:1977 Materials and equipment for petroleum and natural gas industries — Tool joints for steel drill pipe for oil or natural gas wells [Withdrawn without replacement]
• ISO 3963:1977 Fertilizers — Sampling from a conveyor by stopping the belt
• ISO 3964:2016 Dentistry — Coupling dimensions for handpiece connectors
• ISO 3965:1990 Agricultural wheeled tractors — Maximum speeds — Method of determination
• ISO 3966:2020 Measurement of fluid flow in closed conduits – Velocity area method using Pitot static tubes
• ISO 3967 Petroleum products – Determination of density and relative density – Bingham pyknometer method [Rejected draft]
• ISO 3968:2017 Hydraulic fluid power — Filters — Evaluation of differential pressure versus flow
• ISO 3969:1979 Shipbuilding — Inland vessels — Operational documentation
• ISO 3970:1977 Modular units for machine tool construction — Integral way columns — Floor-mounted type
• ISO 3971:1977 Rice milling — Symbols and equivalent terms [Withdrawn without replacement]
• ISO 3972:2011 Sensory analysis — Methodology — Method of investigating sensitivity of taste
• ISO 3973:1996 Living animals for slaughter — Vocabulary — Bovines [Withdrawn without replacement]
• ISO 3974:1977 Definitions of living animals for slaughter — Ovines
• ISO 3975:1977 Definitions of living animals for slaughter — Horses [Withdrawn without replacement]
• ISO 3976:2006 Milk fat — Determination of peroxide value
• ISO 3977 Gas turbines – Procurement
• ISO 3978:1976 Aluminium and aluminium alloys — Determination of chromium — Spectrophotometric method using diphenylcarbazide, after extraction
• ISO 3979:1977 Aluminium and aluminium alloys — Determination of nickel — Spectrophotometric method using dimethylglyoxime [Withdrawn without replacement]
• ISO 3980:1977 Aluminium and aluminium alloys — Determination of copper — Atomic absorption spectrophotometric method
• ISO 3981:1977 Aluminium and aluminium alloys — Determination of nickel — Atomic absorption spectrophotometric method
• ISO 3982 Chemical analysis of aluminum and its alloys — Complexometric determination of mangesium [Rejected draft]
• ISO 3983:1977 Cereals and cereal products — Determination of alpha-amylase activity — Colorimetric method [Withdrawn without replacement]
• ISO 3984:2004 Road vehicles — Rear moving barrier impact test procedure [Withdrawn without replacement]
• ISO/TR 3985:2021 Biotechnology — Data publication — Preliminary considerations and concepts [originally planned ISO 3985 was a rejected draft with an unknown name]
• ISO 3986 Petroleum products — Lubricating wax — Determination of cone penetration [Rejected draft]
• ISO 3987:2010 Petroleum products — Determination of sulfated ash in lubricating oils and additives
• ISO 3988 Determination of Spontaneous ignition temperature [Rejected draft]
• ISO 3989 Measurement of airborne noise emitted by compressor units including prime movers [Rejected draft]
• ISO 3990 Dentistry — Evaluation of antibacterial activity of dental restorative materials, luting cements, fissure sealants and orthodontic bonding or luting materials [Under development; originally planned ISO 3990 was Modular co-ordination — Sizes for co-ordinating lengths and widths of openings in the horizontal plane]
• ISO 3991 Agricultural machinery — Robotic feed systems — Safety [Under development; originally planned ISO 3991 was Modular co-ordination — Sizes for co-ordinating heights of openings in the vertical plane]
• ISO 3992 Petroleum waxes — Determination of needle penetration [Rejected draft]
• ISO 3993:1984 Liquefied petroleum gas and light hydrocarbons — Determination of density or relative density — Pressure hydrometer method
• ISO 3994:2014 Plastics hoses — Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials — Specification
• ISO 3995:1985 Metallic powders — Determination of green strength by transverse rupture of rectangular compacts
• ISO 3996:1995 Road vehicles — Brake hose assemblies for hydraulic braking systems used with non-petroleum-base brake fluid
• ISO 3997 Bitumen and bituminous binders – Determination of needle penetration [Rejected draft]
• ISO 3998:1977 Textiles — Determination of resistance to certain insect pests
• ISO 3999:2004 Radiation protection — Apparatus for industrial gamma radiography — Specifications for performance, design and tests

ISO 4000 – ISO 4999

• ISO 4000 Passenger car tyres and rims
  • ISO 4000-1:2021 Part 1: Tyres (metric series)
  • ISO 4000-2:2021 Part 2: Rims
• ISO 4001:1977 Shipbuilding — Inland navigation — Raft-type life-saving apparatus
• ISO 4002 Equipment for sowing and planting
  • ISO 4002-1:1979 Part 1: Concave disks type D1 — Dimensions
  • ISO 4002-2:1977 Part 2: Flat disks type D2 with single bevel — Dimensions
• ISO 4003:1977 Permeable sintered metal materials — Determination of bubble test pore size
• ISO 4004:1983 Agricultural tractors and machinery — Track widths
• ISO/IEC 4005 Telecommunications and information exchange between systems — Low altitude drone area network (LADAN) [Original draft ISO 4005 was deleted]
• ISO/IEC 4005-1 Part 1: Communication model and requirements [Under development]
• ISO/IEC 4005-2 Part 2: Physical and data link protocols for shared communication [Under development]
• ISO/IEC 4005-3 Part 3: Physical and data link protocols for control communication [Under development]
• ISO/IEC 4005-4 Part 4: Physical and data link protocols for video communication [Under development]
• ISO 4006:1991 Measurement of fluid flow in closed conduits – Vocabulary and symbols
• ISO 4007:2018 Personal protective equipment – Eye and face protection – Vocabulary
• ISO 4008 Road vehicles — Fuel injection pump testing
  • ISO 4008-1:1980 Part 1: Dynamic conditions
  • ISO 4008-2:1983 Part 2: Static conditions
  • ISO 4008-3:1987 Part 3: Application and test procedures
• ISO 4009:2000 Commercial vehicles — Location of electrical and pneumatic connections between towing vehicles and trailers [Withdrawn without replacement]
• ISO 4010:1998 Diesel engines — Calibrating nozzle, delay pintle type
• ISO/TR 4011:1976 Road vehicles — Apparatus for measurement of the opacity of exhaust gas from diesel engines [Withdrawn: replaced with ISO 11614]
• ISO 4012:1978 Concrete — Determination of compressive strength of test specimens [Withdrawn: replaced with ISO 1920-4]
• ISO 4013:1978 Concrete — Determination of flexural strength of test specimens [Withdrawn: replaced with ISO 1920-4]
• ISO 4014:2011 Hexagon head bolts — Product grades A and B
• ISO 4015:1979 Hexagon head bolts — Product grade B — Reduced shank (shank diameter approximately equal to pitch diameter)
• ISO 4016:2011 Hexagon head bolts — Product grade C
• ISO 4017:2014 Fasteners — Hexagon head screws — Product grades A and B
• ISO 4018:2011 Hexagon head screws — Product grade C
• ISO 4019:2001 Structural steels — Cold-formed, welded, structural hollow sections — Dimensions and sectional properties [Withdrawn: replaced with ISO 10799-2]
• ISO 4020:2001 Road vehicles — Fuel filters for diesel engines — Test methods
• ISO 4021:1992 Hydraulic fluid power — Particulate contamination analysis — Extraction of fluid samples from lines of an operating system
• ISO 4022:2018 Permeable sintered metal materials — Determination of fluid permeability
• ISO 4023:2009 Rubber hoses and hose assemblies for steam — Test methods
• ISO 4024:1992 Road vehicles — Ignition coils — Low-tension cable connections
• ISO 4025 The physical and mechanical properties of bagasse particleboards [Rejected draft]
• ISO 4026:2003 Hexagon socket set screws with flat point
• ISO 4027:2003 Hexagon socket set screws with cone point
• ISO 4028:2003 Hexagon socket set screws with dog point
• ISO 4029:2003 Hexagon socket set screws with cup point
• ISO 4030:1983 Road vehicles — Vehicle identification number (VIN) — Location and attachment
• ISO 4031:1978 Information interchange – Representation of local time differentials [Withdrawn: replaced with ISO 8601:1988]
• ISO 4032:2012 Hexagon regular nuts (style 1) — Product grades A and B
• ISO 4033:2012 Hexagon high nuts (style 2) — Product grades A and B
• ISO 4034:2012 Hexagon regular nuts (style 1) — Product grade C [Withdrawn without replacement]
• ISO 4035:2012 Hexagon thin nuts chamfered (style 0) — Product grades A and B
• ISO 4036:2012 Hexagon thin nuts unchamfered (style 0) — Product grade B [Withdrawn without replacement]
• ISO 4037 X and gamma reference radiation for calibrating dosemeters and doserate meters and for determining their response as a function of photon energy
  • ISO 4037-1:1996 Part 1: Radiation characteristics and production
  • ISO 4037-2:1997 Part 2: Dosimetry for radiation protection over the energy ranges from 8 keV to 1,3 MeV and 4 MeV to 9 MeV
  • ISO 4037-3:1999 Part 3: Calibration of area and personal dosemeters and the measurement of their response as a function of energy and angle of incidence
  • ISO 4037-4:2004 Part 4: Calibration of area and personal dosemeters in low energy X reference radiation fields
• ISO 4038:1996 Road vehicles — Hydraulic braking systems — Simple flare pipes, tapped holes, male fittings and hose end fittings
• ISO 4039 Road vehicles — Pneumatic braking systems
  • ISO 4039-1:1998 Part 1: Pipes, male fittings and tapped holes with facial sealing surface
  • ISO 4039-2:1998 Part 2: Pipes, male fittings and holes with conical sealing surface
• ISO 4040:2009 Road vehicles — Location of hand controls, indicators and tell-tales in motor vehicles
• ISO 4041:1978 Rotary drilling equipment — Rotary hoses [Withdrawn without replacement]
• ISO 4042:2018 Fasteners — Electroplated coating systems
• ISO 4043:2016 Simultaneous interpreting — Mobile booths — Requirements
• ISO 4044:2017 Leather — Chemical tests — Preparation of chemical test samples
• ISO 4045:2018 Leather — Chemical tests — Determination of pH and difference figure
• ISO 4046 Paper, board, pulps and related terms – Vocabulary
  • ISO 4046-1:2016 Part 1: Alphabetical index
  • ISO 4046-2:2016 Part 2: Pulping terminology
  • ISO 4046-3:2016 Part 3: Paper-making terminology
  • ISO 4046-4:2016 Part 4: Paper and board grades and converted products
  • ISO 4046-5:2016 Part 5: Properties of pulp, paper and board
• ISO 4047:1977 Leather — Determination of sulphated total ash and sulphated water-insoluble ash
• ISO 4048:2018 Leather — Chemical tests — Determination of matter soluble in dichloromethane and free fatty acid content
• ISO 4049:2019 Dentistry — Polymer-based restorative materials
• ISO 4050:1977 Shipbuilding — Inland vessels — "Rhine" and Hall's stockless anchors
• ISO 4051:1977 Shipbuilding — Inland vessels — Steering gear — Values of torques
• ISO 4052:1983 Coffee — Determination of caffeine content (Reference method) [Withdrawn without replacement]
• ISO 4053 Measurement of gas flow in conduits — Tracer methods
  • ISO 4053-1:1977 Part 1: General [Withdrawn without replacement]
  • ISO 4053-4:1978 Part 4: Transit time method using radioactive tracers [Withdrawn without replacement]
• ISO 4054:1980 Couplers, loose spigots and base-plates for use in working scaffolds made of steel tubes — Requirements and test procedure [Withdrawn without replacement]
• ISO 4055:1977 Road vehicles — Caravans and light trailers — Electromagnetic braking [Withdrawn without replacement]
• ISO 4056:1978 Polyethylene (PE) pipes and fittings — Designation of polyethylene, based on nominal density and melt flow index [Withdrawn: replaced with ISO 10162]
• ISO 4057:1986 Information processing – Data interchange on 6,30 mm (0.25 in) magnetic tape cartridge, 63 bpmm (1 600 bpi) phase-encoded [Withdrawn without replacement]
• ISO 4058:1977 Magnesium and its alloys — Determination of nickel — Photometric method using dimethylglyoxime [Withdrawn without replacement]
• ISO 4059:1978 Polyethylene (PE) pipes — Pressure drop in mechanical pipe-jointing systems — Method of test and requirements
• ISO 4060 Road vehicles — Seat belts — Adjusting devices [Rejected draft]
• ISO 4061 Soldering — Quality requirements for soldering of metallic materials [Under development; original draft ISO 4061 was Road vehicles — Seat belts equipment with push-button buckles — Handling characteristics]
• ISO 4062:1977 Dictation equipment — Symbols [Withdrawn: replaced by ISO 13251]
• ISO 4063:2009 Welding and allied processes – Nomenclature of processes and reference numbers
• ISO 4064 Water meters for cold potable water and hot water
  • ISO 4064-1:2014 Part 1: Metrological and technical requirements
  • ISO 4064-2:2014 Part 2: Test methods
  • ISO 4064-3:2014 Part 3: Test report format
  • ISO 4064-4:2014 Part 4: Non-metrological requirements not covered in ISO 4064-1
  • ISO 4064-5:2014 Part 5: Installation requirements
• ISO 4065:2018 Thermoplastics pipes — Universal wall thickness table
• ISO 4066:1994 Construction drawings — Bar scheduling [Withdrawn: replaced with ISO 3766]
• ISO 4067 Technical drawings — Installations
  • ISO 4067-1:1984 Part 1: Graphical symbols for plumbing, heating, ventilation and ducting [Withdrawn without replacement]
  • ISO 4067-2:1980 Part 2: Simplified representation of sanitary appliances [Withdrawn without replacement]
  • ISO 4067-3:1984 Part 3: Graphical symbols for automatic control [Rejected draft later published as ISO/TR 8545]
  • ISO 4067-6:1985 Part 6: Graphical symbols for supply water and drainage systems in the ground [Withdrawn without replacement]
• ISO 4068:1978 Building and civil engineering drawings — Reference lines [Withdrawn without replacement]
• ISO 4069:1977 Building and civil engineering drawings — Representation of areas on sections and views — General principles [Withdrawn without replacement]
• ISO 4070 Polyvinylidene fluoride (PVDF) — Effect of time and temperature on expected strength [Under development; originally planned standard with this number was a rejected draft with an unknown name]
• ISO 4071:1978 Indirect-reading capacitor-type pocket exposure meters and accessory electrometers [Withdrawn: replaced with ISO 11934, now withdrawn without replacement]
• ISO 4072:1982 Green coffee in bags — Sampling
• ISO 4073:2009 Dentistry — Information system on the location of dental equipment in the working area of the oral health care provider
• ISO 4074:2015 Natural latex rubber condoms – Requirements and test methods
• ISO 4075 Polysulfone (PSU) — Effect of time and temperature on expected strength [Under development; originally planned standard with this number was a rejected draft with an unknown name]
• ISO 4076 Polyphenylsulphone (PPSU) — Effect of time and temperature on expected strength [Under development; originally planned standard with this number was a rejected draft with an unknown name]
• ISO 4077 Coal preparation plant — Guide to sampling in coal preparation plants [Under development; originally planned standard with this number was a rejected draft with an unknown name]
• ISO 4079:2020 Rubber hoses and hose assemblies — Textile-reinforced hydraulic types for oil-based or water-based fluids — Specification
• ISO 4080:2009 Rubber and plastics hoses and hose assemblies — Determination of permeability to gas
• ISO 4081:2016 Rubber hoses and tubing for cooling systems for internal-combustion engines — Specification
• ISO 4082:1981 Road vehicles — Motor vehicles — Flasher units
• ISO 4083 Dental operating chair — General requirements [Rejected Draft]
• ISO 4084:1977 Aircraft — Repairable contactors (not hermetically sealed) — Performance requirements [Withdrawn without replacement]
• ISO 4085:1979 Shipbuilding — Inland navigation — Swing derricks [Withdrawn without replacement]
• ISO 4086:2001 Road vehicles — 90 semi-trailer fifth wheel kingpin — Interchangeability
• ISO 4087:2005 Micrographics – Microfilming of newspapers for archival purposes on 35 mm microfilm
• ISO/TR 4088:1977 Rubber Thread – Classification [Withdrawn without replacement]
• ISO 4089:1979 Shipbuilding — Inland navigation — Sealing rubber for covers of cargo hatches
• ISO 4090:2001 Photography — Medical radiographic cassettes/screens/films and hard-copy imaging films — Dimensions and specifications
• ISO 4091:2003 Road vehicles — Connectors for the electrical connection of towing and towed vehicles — Definitions, tests and requirements
• ISO 4092:1988 Road vehicles — Diagnostic systems for motor vehicles — Vocabulary [Withdrawn without replacement]
• ISO 4093:1999 Diesel engines — Fuel injection pumps — High-pressure pipes for testing
• ISO 4094:2017 Paper, board and pulps — General requirements for the competence of laboratories authorized for the issue of optical reference transfer standards of level 3
• ISO 4095:1998 Aerospace — Bihexagonal drives — Wrenching configuration — Metric series
• ISO 4096:1978 Essential oils (containing tertiary alcohols) — Evaluation of free alcohols content by determination of ester value after cold formylation [Withdrawn without replacement]
• ISO 4097:2020 Rubber, ethylene-propylene-diene (EPDM) — Evaluation procedure
• ISO 4098:2018 Leather — Chemical tests — Determination of water-soluble matter, water-soluble inorganic matter and water-soluble organic matter
• ISO 4099:1984 Cheese — Determination of nitrate and nitrite contents — Method by cadmium reduction and photometry [Withdrawn: replaced with ISO 14673-(1-3)]
• ISO 4100:1980 Road vehicles — World parts manufacturer identifier (WPMI) code
• ISO 4101:1983 Drawn steel wire for elevator ropes — Specifications
• ISO 4102:1984 Equipment for crop protection — Sprayers — Connection threading
• ISO 4103:1979 Concrete — Classification of consistency [Withdrawn without replacement]
• ISO 4104:1984 Dental zinc polycarboxylate cements [Withdrawn: replaced with ISO 9917]
• ISO 4105:1978 Textile machinery and accessories — Wires for flexible card clothings
• ISO 4106:2012 Motorcycles — Engine test code — Net power
• ISO 4107:2010 Commercial vehicles — Wheel-hub attachment dimensions
• ISO 4108:1980 Concrete — Determination of tensile splitting strength of test specimens [Withdrawn: replaced with ISO 1920-4]
• ISO 4109:1980 Fresh concrete — Determination of the consistency — Slump test [Withdrawn: replaced with ISO 1920-2]
• ISO 4110:1979 Fresh concrete — Determination of the consistency — Vebe test [Withdrawn: replaced with ISO 1920-2]
• ISO 4111:1979 Fresh concrete — Determination of consistency — Degree of compactibility (Compaction index) [Withdrawn: replaced with ISO 1920-2]
• ISO 4112:1990 Cereals and pulses — Guidance on measurement of the temperature of grain stored in bulk
• ISO 4113:2010 Road vehicles — Calibration fluids for diesel injection equipment
• ISO/TR 4114:1979 Road vehicles — Caravans and light trailers — Static load on ball couplings [Withdrawn without replacement]
• ISO 4115:1997 Air cargo equipment — Air/land pallet nets
• ISO 4116:1986 Air cargo equipment — Ground equipment requirements for compatibility with aircraft unit load devices
• ISO 4117:1993 Air and air/land cargo pallets — Specification and testing
• ISO 4118:2016 Air cargo — Non-certified lower deck containers — Design and testing
• ISO 4119:1995 Pulps — Determination of stock concentration
• ISO 4120:2021 Sensory analysis — Methodology — Triangle test
• ISO 4121:2003 Sensory analysis — Guidelines for the use of quantitative response scales
• ISO/TR 4122:1977 Equipment for working the soil — Dimensions of flat disks — Type A [Withdrawn without replacement]
• ISO 4123:1979 Belt conveyors — Impact rings for carrying idlers and discs for return idlers — Main dimensions
• ISO 4124:1994 Liquid hydrocarbons — Dynamic measurement — Statistical control of volumetric metering systems
• ISO 4125:1991 Dry fruits and dried fruits – Definitions and nomenclature
• ISO 4126 Safety devices for protection against excessive pressure
  • ISO 4126-1:2013 Part 1: Safety valves
  • ISO 4126-2:2018 Part 2: Bursting disc safety devices
  • ISO 4126-3:2020 Part 3: Safety valves and bursting disc safety devices in combination
  • ISO 4126-4:2013 Part 4: Pilot operated safety valves
  • ISO 4126-5:2013 Part 5: Controlled safety pressure relief systems (CSPRS)
  • ISO 4126-6:2014 Part 6: Application, selection and installation of bursting disc safety devices
  • ISO 4126-7:2013 Part 7: Common data
  • ISO 4126-9:2008 Part 9: Application and installation of safety devices excluding stand-alone bursting disc safety devices
  • ISO 4126-10:2010 Part 10: Sizing of safety valves for gas/liquid two-phase flow
• ISO 4127 Shipbuilding — Inland navigation — Fairleads
  • ISO 4127-1:1979 Part 1: Two-lip fairleads
  • ISO 4127-2:1979 Part 2: Two-Roller fairleads
• ISO 4128:1985 Aircraft — Air mode modular containers
• ISO 4129:2012 Road vehicles – Mopeds – Symbols for controls, indicators and tell-tales [Withdrawn without replacement]
• ISO 4130:1978 Road vehicles – Three-dimensional reference system and fiducial marks – Definitions
• ISO 4131:1979 Road vehicles — Dimensional codes for passenger cars
• ISO 4132:1979 Unplasticized polyvinyl chloride (PVC) and metal adaptor fittings for pipes under pressure — Laying lengths and size of threads — Metric series
• ISO 4133:1979 Meat and meat products — Determination of glucono-delta-lactone content (Reference method) [Withdrawn without replacement]
• ISO 4134:2021 Meat and meat products — Determination of L-(+)-glutamic acid content — Reference method
• ISO 4135:2022 Anaesthetic and respiratory equipment – Vocabulary
• ISO 4136:2012 Destructive tests on welds in metallic materials — Transverse tensile test
• ISO/TR 4137:1978 Plastics — Determination of modulus of elasticity by alternating flexure [Withdrawn without replacement]
• ISO 4138:2021 Passenger cars — Steady-state circular driving behaviour — Open-loop test methods
• ISO 4139:1979 Ferrosilicon – Determination of aluminium content – Flame atomic absorption spectrometric method
• ISO 4140:1979 Ferrochromium and ferrosilicochromium – Determination of chromium content – Potentiometric method
• ISO 4141 Road vehicles — Multi-core connecting cables
  • ISO 4141-1:2019 Part 1: Test methods and requirements for basic performance sheathed cables
  • ISO 4141-2:2019 Part 2: Test methods and requirements for high performance sheathed cables
  • ISO 4141-3:2019 Part 3: Construction, dimensions and marking of unscreened sheathed low-voltage cables
  • ISO 4141-4:2009 Part 4: Test methods and requirements for coiled cable assemblies
• ISO 4142:2002 Laboratory glassware — Test tubes
• ISO 4143:1981 Shipbuilding — Inland vessels — Open rowing lifeboats
• ISO 4144:2003 Pipework — Stainless steel fittings threaded in accordance with ISO 7-1
• ISO 4145:1986 Non-alloy steel fittings threaded to ISO 7-1
• ISO 4146:1980 Shipbuilding — Inland vessels — Manholes [Withdrawn: replaced by ISO 5894]
• ISO 4147:1997 Aerospace — Nuts, hexagonal, slotted (castellated), normal height, normal across flats, with MJ threads, classifications: 600 MPa (at ambient temperature)/120 degrees C, 600 MPa (at ambient temperature)/235 degrees C, 900 MPa (at ambient temperature)/425 degrees C, 1 100 MPa (at ambient temperature)/235 degrees C, 1 100 MPa (at ambient temperature)/315 degrees C, 1 100 MPa (at ambient temperature)/650 degrees C, 1 210 MPa (at ambient temperature)/730 degrees C, 1 250 MPa (at ambient temperature)/235 degrees C and 1 550 MPa (at ambient temperature)/600 degrees C — Dimensions
• ISO 4148:2004 Road vehicles — Special warning lamps — Dimensions
• ISO 4149:2005 Green coffee — Olfactory and visual examination and determination of foreign matter and defects
• ISO 4150:2011 Green coffee or raw coffee — Size analysis — Manual and machine sieving
• ISO 4151:1987 Road vehicles — Mopeds — Type, location and functions of controls [Withdrawn without replacement]
• ISO 4152 Glass‐reinforced thermosetting plastics (GRP) pipes — Determination of the apparent axial long‐term modulus of pipes subject to beam bending [Originally planned ISO 4152 was Welder's test on non-alloy and low-alloy steels for manual metal arc welding]
• ISO 4153:1981 Aircraft — Pressure fuel dispensing system — Test procedure and limit value for shut-off surge pressure
• ISO 4154 Traditional Chinese medicine — Sinomenium acutum stem [Under development]
• ISO 4155 Magnesium and magnesium alloys — Determination of nickel — Inductively coupled plasma optical emission spectrometric method [Under development]
• ISO 4156 Straight cylindrical involute splines — Metric module, side fit
  • ISO 4156-1:2021 Part 1: Generalities
  • ISO 4156-2:2021 Part 2: Dimensions
  • ISO 4156-3:2021 Part 3: Inspection
• ISO 4157 Construction drawings – Designation systems
• ISO 4158:1978 Ferrosilicon, ferrosilicomanganese and ferrosilicochromium – Determination of silicon content – Gravimetric method
• ISO 4159:1978 Ferromanganese and ferrosilicomanganese – Determination of manganese content – Potentiometric method
• ISO 4160 Hexagon nuts and bolts with flange, style 1 — Small Series — Product grade B [Draft merged into ISO 4161 and ISO 4162]
• ISO 4161:2012 Hexagon nuts with flange, style 2 — Coarse thread
• ISO 4162:2012 Hexagon bolts with flange — Small series — Product grade A with driving feature of product grade B
• ISO 4164:2012 Mopeds — Engine test code — Net power
• ISO 4165 Road vehicles — Electrical connections — Double-pole connection
• ISO 4166:1979 Hexagon nuts for fine mechanics — Product grade F [Withdrawn without replacement]
• ISO 4167:2012 Polyolefin agricultural twines
• ISO 4168:2002 Timekeeping instruments — Conditions for carrying out checks on radioluminescent deposits [Withdrawn without replacement]
• ISO 4169:1979 Office machines — Keyboards — Key numbering system and layout charts
• ISO 4170:1995 Air cargo equipment — Interline pallet nets
• ISO 4171:1993 Air cargo equipment — Interline pallets
• ISO 4172:1991 Technical drawings – Construction drawings – Drawings for the assembly of prefabricated structures
• ISO 4173:1980 Ferromolybdenum – Determination of molybdenum content – Gravimetric method
• ISO 4174:1998 Cereals, oilseeds and pulses — Measurement of unit pressure loss in one-dimensional air flow through bulk grain
• ISO 4175:1979 Shipbuilding — Shipborne barges, series 1 — Main dimensions
• ISO 4176:1981 Fertilizers — Determination of nitrate nitrogen content — Nitron gravimetric method [Withdrawn without replacement]
• ISO 4177 Magnesium and magnesium alloys – Determination of chromium – Inductively coupled plasma optical emission spectrometric method [Under development; original draft with this number unknown]
• ISO 4178:1980 Complete, filled transport packages — Distribution trials — Information to be recorded
• ISO 4179 Ductile iron pipes and fittings for pressure and non-pressure pipelines – Cement mortar lining
• ISO 4180:2019 Packaging — Complete, filled transport packages — General rules for the compilation of performance test schedules
• ISO 4181 Magnesium and magnesium alloys — Determination of strontium — Inductively coupled plasma optical emission spectrometric method [Under development; original draft with this number unknown]
• ISO 4182:1999 Motor vehicles — Measurement of variations in dipped-beam headlamp angle as a function of load [Withdrawn without replacement]
• ISO 4183:1995 Belt drives — Classical and narrow V-belts — Grooved pulleys (system based on datum width)
• ISO 4184:1992 Belt drives — Classical and narrow V-belts — Lengths in datum system
• ISO 4185:1980 Measurement of liquid flow in closed conduits – Weighing method
• ISO 4186:1980 Asparagus — Guide to storage
• ISO 4187:1980 Horse-radish — Guide to storage
• ISO 4188 Magnesium and magnesium alloys – Determination of arsenic – Inductively coupled plasma optical emission spectrometric method [Under development; original draft with this number unknown]
• ISO 4189 Magnesium and magnesium alloys — Determination of sodium — Inductively coupled plasma optical emission spectrometric method [Under development; original draft with this number unknown]
• ISO 4190 Lift (US: Elevator) installation
  • ISO 4190-1:2010 Part 1: Class I, II, III and VI lifts [Withdrawn: replaced with ISO 8100-30]
  • ISO 4190-2:2001 Part 2: Class IV lifts
  • ISO 4190-3:1982 Part 3: Service lifts class V
  • ISO 4190-5:2006 Part 5: Control devices, signals and additional fittings
  • ISO 4190-6:1984 Part 6: Passenger lifts to be installed in residential buildings — Planning and selection [Withdrawn: replaced with ISO 8100-32]
• ISO/TR 4191:2014 Plastics piping systems for water supply — Unplasticized poly(vinyl chloride)(PVC-U) and oriented PVC-U (PVC-O) — Guidance for installation
• ISO 4192:1981 Aluminium and aluminium alloys — Determination of lead content — Flame atomic absorption spectrometric method
• ISO 4193:1981 Aluminium and aluminium alloys — Determination of chromium content — Flame atomic absorption spectrometric method
• ISO 4194:1981 Magnesium alloys — Determination of zinc content — Flame atomic absorption spectrometric method
• ISO 4195:2012 Conveyor belts with heat-resistant rubber covers — Heat resistance of covers — Requirements and test methods
• ISO 4196:1984 Graphical symbols — Use of arrows [Withdrawn: replaced with ISO 80416-2]
• ISO 4197:1989 Equipment for working the soil — Hoe blades — Fixing dimensions
• ISO 4198:1984 Surface active agents — Detergents for hand dishwashing — Guide for comparative testing of performance
• ISO 4199:1979 Plain bearings — Shaft diameters for unsplit bushes [Withdrawn without replacement]
• ISO 4200:1991 Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length
• ISO 4202:2016 Reduction sleeves with external 7/24 taper for tools with Morse taper shanks
• ISO 4203:1978 Parallel shank tools — Driving tenons and sockets — Dimensions [Withdrawn without replacement]
• ISO 4204:2016 Countersinks, 90°, with Morse taper shanks and detachable pilots
• ISO 4205:2016 Countersinks, 90°, with parallel shanks and solid pilots
• ISO 4206:2016 Counterbores with parallel shanks and solid pilots
• ISO 4207:2016 Counterbores with Morse taper shanks and detachable pilots
• ISO 4208:1977 Detachable pilots for use with counterbores and 90 degrees countersinks — Dimensions
• ISO 4209 Truck and bus tyres and rims (metric series)
  • ISO 4209-1:2001 Part 1: Tyres
  • ISO 4209-2:2020 Part 2: Rims
• ISO 4210 Cycles — Safety requirements for bicycles
  • ISO 4210-1:2014 Part 1: Terms and definitions
  • ISO 4210-2:2015 Part 2: Requirements for city and trekking, young adult, mountain and racing bicycles
  • ISO 4210-3:2014 Part 3: Common test methods
  • ISO 4210-4:2014 Part 4: Braking test methods
  • ISO 4210-5:2014 Part 5: Steering test methods
  • ISO 4210-6:2015 Part 6: Frame and fork test methods
  • ISO 4210-7:2014 Part 7: Wheels and rims test methods
  • ISO 4210-8:2014 Part 8: Pedal and drive system test methods
  • ISO 4210-9:2014 Part 9: Saddles and seat-post test methods
• ISO 4211:1979 Furniture — Assessment of surface resistance to cold liquids
  • ISO 4211-2:2013 Part 2: Assessment of resistance to wet heat
  • ISO 4211-3:2013 Part 3: Assessment of resistance to dry heat
  • ISO 4211-4:1988 Part 4: Assessment of resistance to impact
  • ISO 4211-5:2021 Part 5: Assessment of resistance to abrasion
• ISO 4212 Corrosion of Metals and Alloys — Method of oxalic acid etching test for intergranular corrosion of austenitic stainless steel [Under development; original draft with this number unknown]
• ISO 4213.2 Information technology — Artificial Intelligence — Assessment of machine learning classification performance [Under development; original draft with this number unknown]
• ISO 4214 Milk and milk products — Determination of amino acids in infant formula and other dairy products [Under development; original draft with this number unknown]
• ISO 4215 Corrosion of metals and alloys — Test method for high-temperature corrosion testing of metallic materials by thermogravimetry under isothermal or cyclic conditions [Under development; original draft with this number unknown]
• ISO 4216:2021 Thermosetting resin and UV curable resin — Determination of shrinkage by continuous measurement method [Original draft with this number unknown]
• ISO 4217:2015 Codes for the representation of currencies
• ISO 4218 Printing machines — Vocabulary
  • ISO 4218-1:1979 Part 1: Fundamental terms
• ISO 4219:1979 Air quality — Determination of gaseous sulphur compounds in ambient air — Sampling equipment
• ISO 4220:1983 Ambient air — Determination of a gaseous acid air pollution index — Titrimetric method with indicator or potentiometric end-point detection
• ISO 4221:1980 Air quality — Determination of mass concentration of sulphur dioxide in ambient air — Thorin spectrophotometric method
• ISO 4222 Ambient air — Measurement of particulate fall-out — Horizontal deposit gauge method [Rejected draft]
• ISO 4223 Definitions of some terms used in the tyre industry
  • ISO 4223-1:2017 Part 1: Pneumatic tyres
  • ISO 4223-2:1991 Part 2: Solid tyres
• ISO 4224:2000 Ambient air — Determination of carbon monoxide — Non-dispersive infrared spectrometric method
• ISO 4225:2020 Air quality – General aspects – Vocabulary
• ISO 4226:2007 Air quality – General aspects – Units of measurement
• ISO/TR 4227:1989 Planning of ambient air quality monitoring
• ISO 4228:1986 Spanners and wrenches — Spline drive ends for power socket wrenches
• ISO 4229:2017 Assembly tools for screws and nuts — Single-head engineer's wrenches for lower torque applications — Maximum outside dimensions of heads and test torques
• ISO 4230:2016 Hand- and machine-operated circular screwing dies for taper pipe threads — R series
• ISO 4231:2016 Hand- and machine-operated circular screwing dies for parallel pipe threads — G series
• ISO 4232 Office machines – Minimum information to be included in specification sheets
  • ISO 4232-1:1979 Part 1: Duplicators [Withdrawn without replacement]
  • ISO 4232-2:1980 Part 2: Document copying machines
  • ISO 4232-3:1984 Part 3: Postal franking machines [Withdrawn without replacement]
• ISO 4233 Hot helium leak testing method for high temperature pressure-bearing components in nuclear fusion reactors [Under development; original draft with this number unknown]
• ISO 4238:1976 Cinematography — Optical printing ratios for enlargement and reduction of motion-picture film images — Specifications
• ISO 4240-1 Fine bubble technology — Environmental applications — Part 1: Inspection method using online particle counter in dissolved air flotation (DAF) plant [Under development; original draft with this number unknown, but relates to Cinematography]
• ISO 4241:2019 Cinematography — Projection film leader (time-based), trailer and cue marks — Specifications
• ISO 4242:1980 Cinematography — Recording head gaps for two sound records on 16 mm magnetic film — Positions and width dimensions
• ISO 4243:1979 Cinematography — Picture image area and photographic sound record on 16 mm motion-picture release prints — Positions and dimensions
• ISO 4244:1979 Cinematography — Photographic sound record on 8 mm Type S motion-picture prints — Position and width dimensions [Withdrawn without replacement]
• ISO 4245 Cinematography — Projector usage of 16 mm motion-picture films for direct front projection — Specifications [Draft numbered as ISO 26, which the draft was a revision of]
• ISO 4246:1994 Cinematography – Vocabulary
• ISO 4247:1977 Jig bushes and accessories for drilling purposes — Dimensions [Withdrawn without replacement]
• ISO 4248:1978 Jig bushes – Definitions and nomenclature
• ISO 4249 Motorcycle tyres and rims (Code-designated series)
  • ISO 4249-1:1985 Part 1: Tyres
  • ISO 4249-2:1990 Part 2: Tyre load ratings
  • ISO 4249-3:2010 Part 3: Rims
• ISO 4250 Earth-mover tyres and rims
  • ISO 4250-1:2017 Part 1: Tyre designation and dimensions
  • ISO 4250-2:2017 Part 2: Loads and inflation pressures
  • ISO 4250-3:2020 Part 3: Rims
• ISO 4251 Code designated diagonal tyres (ply rating marked series) for agricultural tractors, trailers and machines
  • ISO 4251-1:2019 Part 1: Tyre designation and dimensions, and approved rim contours
  • ISO 4251-2:2019 Part 2: Tyre load ratings
  • ISO 4251-3:2006 Part 3: Rims [Withdrawn: replaced with ISO 18804]
  • ISO 4251-4:2010 Part 4: Tyre classification and nomenclature [Withdrawn without replacement]
  • ISO 4251-5:1992 Part 5: Logging and forestry service tyres [Withdrawn: replaced with ISO 18807]
• ISO 4252:2007 Agricultural tractors — Operator's workplace, access and exit — Dimensions
• ISO 4253:1993 Agricultural tractors — Operator's seating accommodation — Dimensions
• ISO 4254 Agricultural machinery — Safety
  • ISO 4254-1:2013 Part 1: General requirements
  • ISO 4254-2:1986 Part 2: Anhydrous ammonia applicators [Withdrawn without replacement]
  • ISO 4254-3:1992 Part 3: Tractors [Withdrawn: replaced with ISO 26322-(1,2)]
  • ISO 4254-4:1990 Part 4: Forestry winches [Withdrawn: replaced by ISO 19472]
  • ISO 4254-5:2018 Part 5: Power-driven soil-working machines
  • ISO 4254-6:2020 Part 6: Sprayers and liquid fertilizer distributors
  • ISO 4254-7:2017 Part 7: Combine harvesters, forage harvesters, cotton harvesters and sugar cane harvesters
  • ISO 4254-8:2018 Part 8: Solid fertilizer distributors
  • ISO 4254-9:2018 Part 9: Seed drills
  • ISO 4254-10:2009 Part 10: Rotary tedders and rakes
  • ISO 4254-11:2010 Part 11: Pick-up balers
  • ISO 4254-12:2012 Part 12: Rotary disc and drum mowers and flail mowers
  • ISO 4254-13:2012 Part 13: Large rotary mowers
  • ISO 4254-14:2016 Part 14: Bale wrappers
  • ISO 4254-15 Part 15: Row-crop flail mowers [Abandoned draft]
  • ISO 4254-16:2018 Part 16: Portable agricultural grain augers
  • ISO 4254-17:2022 Part 17: Root crop harvesters
• ISO 4256:1996 Liquefied petroleum gases — Determination of gauge vapour pressure — LPG method
• ISO 4257:2001 Liquefied petroleum gases — Method of sampling
• ISO 4259 Petroleum and related products — Precision of measurement methods and results
  • ISO 4259-1:2017 Part 1: Determination of precision data in relation to methods of test
  • ISO 4259-2:2017 Part 2: Interpretation and application of precision data in relation to methods of test
  • ISO 4259-3:2020 Part 3: Monitoring and verification of published precision data in relation to methods of test
  • ISO 4259-4:2021 Part 4: Use of statistical control charts to validate 'in-statistical-control' status for the execution of a standard test method in a single laboratory
• ISO 4260:1987 Petroleum products and hydrocarbons — Determination of sulfur content — Wickbold combustion method [Withdrawn without replacement]
• ISO 4261:2013 Petroleum products — Fuels (class F) — Specifications of gas turbine fuels for industrial and marine applications
• ISO 4262:1993 Petroleum products — Determination of carbon residue — Ramsbottom method
• ISO 4263 Petroleum and related products — Determination of the ageing behaviour of inhibited oils and fluids — TOST test
  • ISO 4263-1:2003 Part 1: Procedure for mineral oils
  • ISO 4263-2:2003 Part 2: Procedure for category HFC hydraulic fluids
  • ISO 4263-3:2015 Part 3: Anhydrous procedure for synthetic hydraulic fluids
  • ISO 4263-4:2006 Part 4: Procedure for industrial gear oils
• ISO 4264:2018 Petroleum products — Calculation of cetane index of middle-distillate fuels by the four variable equation
• ISO 4265:1986 Petroleum products — Lubricating oils and additives — Determination of phosphorus content — Quinoline phosphomolybdate method [Withdrawn without replacement]
• ISO 4266 Petroleum and liquid petroleum products — Measurement of level and temperature in storage tanks by automatic methods
  • ISO 4266-1:2002 Part 1: Measurement of level in atmospheric tanks
  • ISO 4266-2:2002 Part 2: Measurement of level in marine vessels
  • ISO 4266-3:2002 Part 3: Measurement of level in pressurized storage tanks (non-refrigerated)
  • ISO 4266-4:2002 Part 4: Measurement of temperature in atmospheric tanks
  • ISO 4266-5:2002 Part 5: Measurement of temperature in marine vessels
  • ISO 4266-6:2002 Part 6: Measurement of temperature in pressurized storage tanks (non-refrigerated)
• ISO 4267 Petroleum and liquid petroleum products — Calculation of oil quantities
  • ISO 4267-1 Part 1: Static measurement [Rejected draft]
  • ISO 4267-2:1988 Part 2: Dynamic measurement
• ISO 4268:2000 Petroleum and liquid petroleum products — Temperature measurements — Manual methods
• ISO 4269:2001 Petroleum and liquid petroleum products — Tank calibration by liquid measurement — Incremental method using volumetric meters
• ISO 4270 Petroleum products – Determination of density and relative density – Reischauer pyknometer method [Rejected draft]
• ISO 4271 Petroleum products – Determination of density and relative density – Conical pyknometer method [Rejected draft]
• ISO 4272 Intelligent transport systems — Truck platooning systems (TPS) — Functional and operational requirements [Under development; original draft with this number unknown]
• ISO 4273 Intelligent transport systems — Automated braking during low speed manoeuvring (ABLS) — Requirements and test procedures [Under development; original draft with this number unknown]
• ISO 4274:1977 Urea for industrial use — Determination of biuret content — Flame atomic absorption and photometric absorption methods [Withdrawn without replacement]
• ISO 4275:1977 Ammonium hydrogen carbonate for industrial use (including foodstuffs) — Determination of arsenic content — Silver diethyldithiocarbamate photometric method [Withdrawn without replacement]
• ISO 4276:1978 Anhydrous ammonia for industrial use — Evaluation of residue on evaporation — Gravimetric method [Withdrawn without replacement]
• ISO/TR 4277:2009 Cryolite, natural and artificial — Conventional test for evaluation of free fluorides content
• ISO 4278:1977 Sodium fluoride for industrial use — Determination of carbonate content — Gravimetric method [Withdrawn without replacement]
• ISO 4279:1977 Aluminium fluoride for industrial use — Determination of sodium content — Flame emission spectrophotometric method [Withdrawn without replacement]
• ISO 4280:1977 Cryolite, natural and artificial, and aluminium fluoride for industrial use — Determination of sulphate content — Barium sulphate gravimetric method
• ISO 4281:1977 Sodium hexafluorosilicate for industrial use — Determination of free acidity and total hexafluorosilicate content — Titrimetric method
• ISO 4282:1992 Acid-grade and ceramic-grade fluorspar — Determination of loss in mass at 105 degrees C [Withdrawn without replacement]
• ISO 4283:1993 All grades of fluorspar — Determination of carbonate content — Titrimetric method [Withdrawn without replacement]
• ISO 4284:1993 Acid-grade and ceramic-grade fluorspar — Determination of sulfide content — Iodometric method [Withdrawn without replacement]
• ISO 4285:1977 Phosphoric acid for industrial use — Guide to sampling techniques
• ISO 4286:2021 Intelligent transport systems — Use cases for sharing of probe data [Original draft with this number unknown]
• ISO 4287:1997 Geometrical Product Specifications (GPS) – Surface texture: Profile method – Terms, definitions and surface texture parameters [Withdrawn: replaced with ISO 21920-2]
• ISO 4288:1996 Geometrical Product Specifications (GPS) – Surface texture: Profile method – Rules and procedures for the assessment of surface texture [Withdrawn: replaced with ISO 21920-3]
• ISO 4289 Recommendation and specification of HVOF cermet coatings for metallurgical roll components [Under development; originally planned ISO 4289 was Instruments for the measurement of surface roughness by the profile method contact (stylus) instruments of consecutive profile transformation - Profile recording instruments calibration and means]
• ISO 4290 Agricultural wheeled tractors and attachments — Front loaders — Dimensional and operational ratings [Under development; original draft with this number unknown]
• ISO 4291:1985 Methods for the assessment of departure from roundness – Measurement of variations in radius
• ISO 4292:1985 Methods for the assessment of departure from roundness — Measurement by two- and three-point methods [Withdrawn without replacement]
• ISO 4293:1982 Manganese ores and concentrates — Determination of phosphorus content — Extraction-molybdovanadate photometric method
• ISO 4294:1984 Manganese ores and concentrates — Determination of copper content — Extraction-spectrometric and spectrometric methods [Withdrawn without replacement]
• ISO 4295:1988 Manganese ores and concentrates — Determination of aluminium content — Photometric and gravimetric methods
• ISO 4296 Manganese ores — Sampling
  • ISO 4296-1:1984 Part 1: Increment sampling
  • ISO 4296-2:1983 Part 2: Preparation of samples
• ISO 4297:1978 Manganese ores and concentrates — Methods of chemical analysis — General instructions
• ISO 4298:1984 Manganese ores and concentrates — Determination of manganese content — Potentiometric method
• ISO 4299:1989 Manganese ores — Determination of moisture content
• ISO 4300:1984 Manganese ores and concentrates — Determination of lead content — Polarographic methods [Withdrawn without replacement]
• ISO 4301 Cranes – Classification
  • ISO 4301-1:2016 Part 1: General
  • ISO 4301-2:2020 Part 2: Mobile cranes
  • ISO 4301-3:2021 Part 3: Tower cranes
  • ISO 4301-4:1989 Part 4: Jib cranes
  • ISO 4301-5:1991 Part 5: Overhead travelling and portal bridge cranes
• ISO 4302:2016 Cranes — Wind load assessment
• ISO 4304:1987 Cranes other than mobile and floating cranes — General requirements for stability
• ISO 4305:2014 Mobile cranes — Determination of stability
• ISO 4306 Cranes – Vocabulary
  • ISO 4306-1:2007 Part 1: General
  • ISO 4306-2:2012 Part 2: Mobile cranes
  • ISO 4306-3:2016 Part 3: Tower cranes
  • ISO 4306-4:2020 Part 4: Jib cranes
  • ISO 4306-5:2005 Part 5: Bridge and gantry cranes
• ISO 4307:2021 Molecular in vitro diagnostic examinations — Specifications for pre-examination processes for saliva — Isolated human DNA [Original draft with this number was related to cranes]
• ISO 4308 Cranes and lifting appliances — Selection of wire ropes
  • ISO 4308-1:2003 Part 1: General [Withdrawn: replaced with ISO 16625]
  • ISO 4308-2:1988 Part 2: Mobile cranes — Coefficient of utilization [Withdrawn: replaced with ISO 16625]
• ISO 4309:2017 Cranes — Wire ropes — Care and maintenance, inspection and discard
• ISO 4310:2009 Cranes — Test code and procedures
• ISO 4311:1979 Anionic and non-ionic surface active agents — Determination of the critical micellization concentration — Method by measuring surface tension with a plate, stirrup or ring
• ISO 4312:1989 Surface active agents — Evaluation of certain effects of laundering — Methods of analysis and test for unsoiled cotton control cloth
• ISO 4313:1976 Washing powders — Determination of total phosphorus(V) oxide content — Quinoline phosphomolybdate gravimetric method
• ISO 4314:1977 Surface active agents — Determination of free alkalinity or free acidity — Titrimetric method
• ISO 4315:1977 Surface active agents — Determination of alkalinity — Titrimetric method
• ISO 4316:1977 Surface active agents — Determination of pH of aqueous solutions — Potentiometric method
• ISO 4317:2011 Surface-active agents and detergents — Determination of water content — Karl Fischer methods
• ISO 4318:1989 Surface active agents and soaps — Determination of water content — Azeotropic distillation method
• ISO 4319:1977 Surface active agents — Detergents for washing fabrics — Guide for comparative testing of performance
• ISO 4320:1977 Non-ionic surface active agents — Determination of cloud point index — Volumetric method
• ISO 4321:1977 Washing powders — Determination of active oxygen content — Titrimetric method
• ISO 4322:1977 Non-ionic surface active agents — Determination of sulphated ash — Gravimetric method
• ISO 4323:2018 Soaps — Determination of chloride content — Potentiometric method
• ISO 4324:1977 Surface active agents — Powders and granules — Measurement of the angle of repose
• ISO 4325:1990 Soaps and detergents — Determination of chelating agent content — Titrimetric method
• ISO 4326:1980 Non-ionic surface active agents — Polyethoxylated derivatives — Determination of hydroxyl value — Acetic anhydride method
• ISO 4327:1979 Non-ionic surface active agents — Polyalkoxylated derivatives — Determination of hydroxyl value — Phthalic anhydride method
• ISO 4328 Centre holes [Rejected draft]
• ISO 4329 Shaft ends with woodruff keys [Rejected draft]
• ISO 4330:1994 Photography — Determination of the curl of photographic film and paper [Withdrawn: replaced with ISO 18910]
• ISO 4331:1986 Photography — Processed photographic black-and-white film for archival records — Silver-gelatin type on cellulose ester base — Specifications [Withdrawn: replaced with ISO 10602, now replaced with ISO 18901]
• ISO 4332:1986 Photography — Processed photographic black-and-white film for archival records — Silver-gelatin type on poly(ethylene terephthalate) base — Specifications [Withdrawn: replaced with ISO 10602, now replaced with ISO 18901]
• ISO 4333 Textiles — Determination of reduction activity of specific proteins derived from pollen, mite and other sources on textile products [Under development; original draft with this number unknown]
• ISO 4334 Fruit puree — Specifications and test methods [Under development; original draft with this number unknown]
• ISO/IEC 4335:1993 Information technology —- Telecommunications and information exchange between systems — High-level data link control (HDLC) procedures — Elements of procedures [Withdrawn: replaced with ISO/IEC 13239]
• ISO 4336:1981 Numerical control of machines — Specification of interface signals between the numerical control unit and the electrical equipment of an NC machine [Withdrawn without replacement]
• ISO 4337:1977 Information processing – Interchangeable magnetic twelve-disk pack (100 Mbytes) [Withdrawn without replacement]
• ISO 4338 Information processing – Magnetic tape cassette [Rejected draft; a later proposed ISO 4338 Conceptual model and system architecture of smart classroom was deleted in 2021]
• ISO 4339:2022 Information technology for learning, education and training — Reference model for information and communications technology (ICT) evaluation in education [Original draft with this number related to Information processing]
• ISO 4340 Water aggressiveness evaluation and optimized lining choice [Under development; original draft with this number related to Information processing]
• ISO 4341:1978 Information processing – Magnetic tape cassette and cartridge labelling and file structure for information interchange
• ISO 4342:1985 Numerical control of machines — NC processor input — Basic part program reference language
• ISO 4343:2000 Industrial automation systems — Numerical control of machines — NC processor output — Post processor commands
• ISO 4344:2004 Steel wire ropes for lifts — Minimum requirements
• ISO 4345:1988 Steel wire ropes — Fibre main cores — Specification
• ISO 4346:1977 Steel wire ropes for general purposes – Lubricants – Basic requirements
• ISO 4347:2015 Leaf chains, clevises and sheaves — Dimensions, measuring forces, tensile strengths and dynamic strengths
• ISO 4348:1983 Flat-top chains and associated chain wheels for conveyors [Withdrawn without replacement]
• ISO 4349 Solid recovered fuels — Method for the determination of the Recycling-Index [Under development; original draft with this number was Genera! principles for the verification of safety of concrete structures]
• ISO 4351 Geometrical product specifications (GPS) — Association [Under development; original draft with this number unknown]
• ISO 4354:2009 Wind actions on structures
• ISO 4355:2013 Bases for design of structures — Determination of snow loads on roofs
• ISO 4356:1977 Bases for the design of structures — Deformations of buildings at the serviceability limit states [Withdrawn without replacement]
• ISO 4357 Rules for use of the I.S. system of units in buildings [Rejected draft]
• ISO 4358 Test methods for civil multi-copter unmanned aircraft system [Under development; original draft with this number unknown]
• ISO 4359:2013 Flow measurement structures – Rectangular, trapezoidal and U-shaped flumes
• ISO 4360:2020 Hydrometry – Open channel flow measurement using triangular profile weirs
• ISO 4361 Liquid flow measurement in open channels by weirs and flumes – Round nosed broad crested weirs [Rejected draft]
• ISO 4362:1999 Hydrometric determinations – Flow measurement in open channels using structures – Trapezoidal broad-crested weirs
• ISO 4363:2002 Measurement of liquid flow in open channels – Methods for measurement of characteristics of suspended sediment
• ISO 4364:1997 Measurement of liquid flow in open channels – Bed material sampling
• ISO 4365:2005 Liquid flow in open channels – Sediment in streams and canals – Determination of concentration, particle size distribution and relative density
• ISO 4366:2007 Hydrometry – Echo sounders for water depth measurements
• ISO 4369:1979 Measurement of liquid flow in open channels – Moving-boat method
• ISO 4370 Environmental life cycle assessment and recycling of ductile iron pipes for water applications [Under development; original draft with this number unknown]
• ISO 4371:1984 Measurement of liquid flow in open channels by weirs and flumes – End depth method for estimation of flow in non-rectangular channels with a free overfall (approximate method) [Withdrawn: replaced with ISO 18481]
• ISO 4373:2022 Hydrometry – Water level measuring devices
• ISO 4374:1990 Liquid flow measurement in open channels – Round-nose horizontal broad-crested weirs
• ISO 4375:2014 Hydrometry – Cableway systems for stream gauging
• ISO 4376 Cycle Energy Requirement — Acceptance Test [Under development; original draft with this number unknown]
• ISO 4377:2012 Hydrometric determinations – Flow measurement in open channels using structures – Flat-V weirs
• ISO 4378 Plain bearings – Terms, definitions, classification and symbols
  • ISO 4378-1:2017 Part 1: Design, bearing materials and their properties
  • ISO 4378-2:2017 Part 2: Friction and wear
  • ISO 4378-3:2017 Part 3: Lubrication
  • ISO 4378-4:2009 Part 4: Basic symbols
  • ISO 4378-5:2009 Part 5: Application of symbols
  • ISO/TR 4378-6:2012 Part 6: Abbreviated terms
• ISO 4379:2018 Plain bearings — Copper alloy bushes
• ISO 4380 Plain bearings – Method of calculation of hydrodynamic thrust bearings (Rejected draft; now covered by ISO 12131-1)
• ISO 4381:2011 Plain bearings — Tin casting alloys for multilayer plain bearings
• ISO 4382 Plain bearings — Copper alloys
  • ISO 4382-1:2021 Part 1: Cast copper alloys for solid and multilayer thick-walled plain bearings
  • ISO 4382-2:2021 Part 2: Wrought copper alloys for solid plain bearings
• ISO 4383:2012 Plain bearings — Multilayer materials for thin-walled plain bearings
• ISO 4384 Plain bearings — Hardness testing of bearing metals
  • ISO 4384-1:2019 Part 1: Multilayer bearings materials
  • ISO 4384-2:2022 Part 2: Solid materials
• ISO 4385:1981 Plain bearings — Compression testing of metallic bearing materials
• ISO 4386 Plain bearings — Metallic multilayer plain bearings
  • ISO 4386-1:2019 Part 1: Non-destructive ultrasonic testing of bond of thickness greater than or equal to 0,5 mm
  • ISO 4386-3:2019 Part 2: Destructive testing of bond for bearing metal layer thicknesses greater than or equal to 2 mm
• ISO 4387:2019 Cigarettes — Determination of total and nicotine-free dry particulate matter using a routine analytical smoking machine
• ISO 4388:1991 Cigarettes — Determination of the smoke condensate retention index of a filter — Direct spectrometric method
• ISO 4389:2000 Tobacco and tobacco products — Determination of organochlorine pesticide residues — Gas chromatographic method
• ISO 4391:1983 Hydraulic fluid power — Pumps, motors and integral transmissions — Parameter definitions and letter symbols
• ISO 4392 Hydraulic fluid power — Determination of characteristics of motors
  • ISO 4392-1:2002 Part 1: At constant low speed and constant pressure
  • ISO 4392-2:2002 Part 2: Startability
  • ISO 4392-3:1993 Part 3: At constant flow and at constant torque
• ISO 4393:2015 Fluid power systems and components — Cylinders — Basic series of piston strokes
• ISO 4394 Fluid power systems and components — Cylinder barrels
  • ISO 4394-1:1980 Part 1: Requirements for steel tubes with specially finished bores [Withdrawn without replacement]
• ISO 4395:2009 Fluid power systems and components — Cylinder piston rod end types and dimensions
• ISO 4396 Telecommunications and information exchange between systems — Future network recursive inter-network architecture [Under development; original DPR with this number related to fluid power]
• ISO 4397:2011 Fluid power connectors and associated components — Nominal outside diameters of tubes and nominal hose sizes
• ISO 4398 Intelligent transport systems — Guided transportation service planning data exchange [Under development; original DPR with this number related to fluid power]
• ISO 4399:2019 Fluid power systems and components — Connectors and associated components — Nominal pressures
• ISO 4400:1994 Fluid power systems and components — Three-pin electrical plug connectors with earth contact — Characteristics and requirements
• ISO 4401:2005 Hydraulic fluid power — Four-port directional control valves — Mounting surfaces
• ISO 4402:1991 Hydraulic fluid power — Calibration of automatic-count instruments for particles suspended in liquids — Method using classified AC Fine Test Dust contaminant [Withdrawn: replaced with ISO 11171]
• ISO 4404 Petroleum and related products — Determination of the corrosion resistance of fire-resistant hydraulic fluids
• ISO 4404-1:2012 Part 1: Water-containing fluids
• ISO 4404-2:2010 Part 2: Non-aqueous fluids
• ISO 4405:1991 Hydraulic fluid power — Fluid contamination — Determination of particulate contamination by the gravimetric method
• ISO 4406:2021 Hydraulic fluid power — Fluids — Method for coding the level of contamination by solid particles
• ISO 4407:2002 Hydraulic fluid power — Fluid contamination — Determination of particulate contamination by the counting method using an optical microscope
• ISO 4408 Hydraulic fluid power — Fluid contamination — Determination of particulate contamination by the counting method under incident light [Incomplete draft]
• ISO 4409 Hydraulic fluid power — Positive-displacement pumps, motors and integral transmissions — Methods of testing and presenting basic steady state performance
• ISO 4410 Experimental characterization of in-plane permeability of fibrous reinforcements for liquid composite moulding [Under development; original draft with this number unknown]
• ISO 4411:2019 Hydraulic fluid power — Valves — Determination of differential pressure/flow rate characteristics
• ISO 4412 Hydraulic fluid power – Test code for determination of airborne noise levels
  • ISO 4412-1:1991 Part 1: Pumps
  • ISO 4412-2:1991 Part 2: Motors
  • ISO 4412-3:1991 Part 3: Pumps – Method using a parallelepiped microphone array
• ISO 4413:2010 Hydraulic fluid power – General rules and safety requirements for systems and their components
• ISO 4414:2010 Pneumatic fluid power — General rules and safety requirements for systems and their components
• ISO 4415:1981 Size designation of clothes — Men's and boys' underwear, nightwear and shirts [Withdrawn: replaced with ISO 8559-2]
• ISO 4416:1981 Size designation of clothes — Women's and girls' underwear, nightwear, foundation garments and shirts [Withdrawn: replaced with ISO 8559-2]
• ISO 4417:1977 Size designation of clothes — Headwear [Withdrawn: replaced with ISO 8559-2]
• ISO 4418:1978 Size designation of clothes — Gloves [Withdrawn: replaced with ISO 8559-2]
• ISO 4419 Health informatics — Reducing clinicians burden [Under development; original draft with this number unknown]
• ISO 4420 Fluid power control components [Rejected draft]
• ISO 4421 Health informatics — Introduction to Ayurveda [Under development; original draft with this number unknown]
• ISO 4422 Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply — Specifications
  • ISO 4422-1:1996 Part 1: General [Withdrawn: replaced with ISO 1452-1]
  • ISO 4422-2:1996 Part 2: Pipes (with or without integral sockets) [Withdrawn: replaced with ISO 1452-2]
  • ISO 4422-3:1996 Part 3: Fittings and joints [Withdrawn: replaced with ISO 1452-3]
  • ISO 4422-4:1996 Part 4: Valves and ancillary equipment [Withdrawn: replaced with ISO 1452-4]
  • ISO 4422-5:1996 Part 5: Fitness for purpose of the system [Withdrawn: replaced with ISO 1452-5]
• ISO 4424 Genomics Informatics — Data Elements and their Metadata for Describing the Tumor Mutation Burden (TMB) Information of Clinical Massive Parallel DNA Sequencing [Under development; original draft with this number unknown]
• ISO 4425 Genomics Informatics — Data elements and their metadata for describing the microsatellite instability (MSI) information of clinical massive parallel DNA sequencing [Under development; original draft with this number unknown]
• ISO 4426:2021 Intelligent transport systems — Lower layer protocols for usage in the European digital tachograph [Original draft with this number unknown]
• ISO 4427 Plastics piping systems for water supply and for drainage and sewerage under pressure — Polyethylene (PE)
• ISO 4427-1:2019 Part 1: General
• ISO 4427-2:2019 Part 2: Pipes
• ISO 4427-3:2019 Part 3: Fittings
• ISO 4427-5:2019 Part 5: Fitness for purpose of the system
• ISO 4428 [Rejected draft related to engineering]
• ISO 4429 [Rejected draft related to engineering]
• ISO 4433 Thermoplastics pipes — Resistance to liquid chemicals — Classification
  • ISO 4433-1:1997 Part 1: Immersion test method
  • ISO 4433-2:1997 Part 2: Polyolefin pipes
  • ISO 4433-3:1997 Part 3: Unplasticized poly(vinyl chloride) (PVC-U), high-impact poly (vinyl chloride) (PVC-HI) and chlorinated poly (vinyl chloride) (PVC-C) pipes
  • ISO 4433-4:1997 Part 4: Poly(vinylidene fluoride) (PVDF) pipes
• ISO 4434:1977 Unplasticized polyvinyl chloride (PVC) adaptor fittings for pipes under pressure — Laying length and size of threads — Metric series [Withdrawn: replaced with ISO 1452-3]
• ISO 4435:2003 Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U)
• ISO 4437 Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE)
  • ISO 4437-1:2014 Part 1: General
  • ISO 4437-2:2014 Part 2: Pipes
  • ISO 4437-3:2014 Part 3: Fittings
  • ISO 4437-4:2014 Part 4: Valves
  • ISO 4437-5:2014 Part 5: Fitness for purpose of the system
• ISO 4439:1969 Unplasticized polyvinyl chloride (PVC) pipes and fittings — Determination and specification of density
• ISO 4440 Thermoplastics pipes and fittings — Determination of melt mass-flow rate
• ISO 4440-1:1994 Part 1: Test method [Withdrawn without replacement]
• ISO 4440-2:1994 Part 2: Test conditions [Withdrawn without replacement]
• ISO 4443:2022 Cryolite primarily used for the production of aluminium — Determination of elements — Wavelength-dispersive X-ray fluorescence spectrometric method using pressed powder tablets [Original draft with this number unknown]
• ISO 4444 Agricultural sprayers — Recording of spray drift parameters [Under development: original draft with this number unknown]
• ISO/TR 4445:2021 Intelligent transport systems — Mobility integration — Role model of ITS service application in smart cities [Original draft with this number unknown]
• ISO 4447:2022 Intelligent transport systems — Mobility integration — Comparison of two mainstream integrated mobility concepts [Original draft with this number unknown]
• ISO 4449 Unplasticized polyvinyl chloride (PVC) pipes and fittings — Determination of longitudinal reversion — oven method [Rejected draft]
• ISO/TR 4450:2020 Quality management systems — Guidance for the application of ISO 19443:2018 [Original draft with this number unknown]
• ISO 4451 Polyethylene (PE) pipes and fittings — Determination of reference density of uncoloured and black polyethylenes [Withdrawn without replacement]
• ISO 4453 Polyethylene (PE) pipes and fittings — Determination of longitudinal reversion — Determination of longitudinal reversion — oven method [Rejected draft]
• ISO 4454 Genomics informatics — Phenopackets: A format for phenotypic data exchange [Under development: original draft with this number unknown]
• ISO 4455 Fixing method for parallel shanks [Rejected draft]
• ISO 4456 [Rejected draft]
• ISO 4457 [Rejected draft]
• ISO 4458 [Rejected draft]
• ISO 4459 [Rejected draft]
• ISO 4460 [Rejected draft]
• ISO 4461 [Rejected draft]
• ISO 4462 Tolerances for building [Rejected draft]
• ISO 4463 Measurement methods for building — Setting-out and measurement
• ISO 4463-1:1989 Part 1: Planning and organization, measuring procedures, acceptance criteria
• ISO 4463-2:1995 Part 2: Measuring stations and targets
• ISO 4463-3:1995 Part 3: Check-lists for the procurement of surveys and measurement services
• ISO 4464:1980 Tolerances for building — Relationship between the different types of deviations and tolerances used for specification [Withdrawn: replaced with ISO 1803, now replaced by ISO 6707-1]
• ISO 4465 Textiles — Animal welfare in the supply chain — General requirements for the production, preparation and traceability of Angora rabbit fibre, including ethical claims and supporting information [Under development: original draft with this number unknown]
• ISO 4466 Layout of monolingual classified vocabularies [Rejected draft]
• ISO/TR 4467:1982 Addendum modification of the teeth of cylindrical gears for speed-reducing and speed-increasing gear pairs [Withdrawn: replaced with ISO 21771]
• ISO 4468:2020 Gear hobs — Accuracy requirements
• ISO 4469:1981 Wood — Determination of radial and tangential shrinkage [Withdrawn: replaced with ISO 13061-13]
• ISO 4470:1981 Sawn timber — Determination of the average moisture content of a lot
• ISO 4471:1982 Wood — Sampling sample trees and logs for determination of physical and mechanical properties of wood in homogeneous stands
• ISO 4472:1983 Coniferous and broadleaved sawn timber — Transportation packages
• ISO 4473:1988 Coniferous and broadleaved tree sawlogs — Visible defects — Classification [Withdrawn: replaced with ISO 24294]
• ISO 4474:1989 Coniferous and broadleaved tree sawlogs — Visible defects — Terms and definitions [Withdrawn: replaced with ISO 24294]
• ISO 4475:1989 Coniferous and broadleaved tree sawlogs — Visible defects — Measurement
• ISO 4476:1983 Coniferous and broadleaved sawlogs — Sizes — Vocabulary [Withdrawn: replaced with ISO 24294]
• ISO 4477 Coniferous sawlogs — Sizes and tolerances [Rejected draft]
• ISO 4480 Coniferous sawlogs — Measurement of sizes and determination of volume [Withdrawn: replaced with ISO 13059]
• ISO 4481:1977 Cutlery and flatware – Nomenclature
• ISO 4482:1979 Asbestos-cement pipelines — Guide for laying [Withdrawn without replacement]
• ISO 4483:1979 Asbestos-cement pipelines — Field pressure testing [Withdrawn without replacement]
• ISO 4484 Textiles and textile products — Microplastics from textile sources [Under development: original draft with this number unknown]
  • ISO 4484-1 Part 1: Determination of material loss from fabrics during washing [Under development]
  • ISO 4484-2 Part 2: Qualitative and quantitative evaluation of microplastics [Under development]
  • ISO 4484-3 Part 3: Measurement of collected material mass released from textile end products by domestic washing method [Under development]
• ISO 4486:1985 Asbestos-cement ventilation ducts and fittings — Dimensions and characteristics [Withdrawn without replacement]
• ISO 4488:1979 Asbestos-cement pipes and joints for thrust-boring and pipe jacking [Withdrawn without replacement]
• ISO 4489:2019 Hardmetals — Sampling and testing
• ISO 4490:2018 Metallic powders — Determination of flow rate by means of a calibrated funnel (Hall flowmeter)
• ISO 4491 Metallic powders — Determination of oxygen content by reduction methods
  • ISO 4491-1:1989 Part 1: General guidelines
  • ISO 4491-2:1997 Part 2: Loss of mass on hydrogen reduction (hydrogen loss)
  • ISO 4491-3:1997 Part 3: Hydrogen-reducible oxygen
  • ISO 4491-4:2019 Part 4: Total oxygen by reduction-extraction
• ISO 4492:2017 Metallic powders, excluding powders for hardmetals — Determination of dimensional changes associated with compacting and sintering
• ISO 4493:1981 Metallic powders — Determination of hydrogen reducible oxygen content [Withdrawn: Replaced with ISO 4491-3]
• ISO 4495:1978 Lubricated metallic powders — Determination of lubricant content — Soxhlet extraction method [Withdrawn: Replaced with ISO 13944]
• ISO 4496:2017 Metallic powders — Determination of acid-insoluble content in iron, copper, tin and bronze powders
• ISO 4497:2020 Metallic powders — Determination of particle size by dry sieving
• ISO 4498:2010 Sintered metal materials, excluding hardmetals — Determination of apparent hardness and microhardness
• ISO 4499 Hardmetals — Metallographic determination of microstructure
• ISO 4499-1:2020 Part 1: Photomicrographs and description
• ISO 4499-2:2020 Part 2: Measurement of WC grain size
• ISO 4499-3:2016 Part 3: Measurement of microstructural features in Ti (C, N) and WC/cubic carbide based hardmetals
• ISO 4499-4:2016 Part 4: Characterisation of porosity, carbon defects and eta-phase content
• ISO 4548 Methods of test for full-flow lubricating oil filters for internal combustion engines
  • ISO 4548-7:2012 Part 7: Vibration fatigue test
• ISO 4551:1987 Ferroalloys – Sampling and sieve analysis
• ISO 4552 Ferroalloys – Sampling and sample preparation for chemical analysis
  • ISO 4552-1:1987 Part 1: Ferrochromium, ferrosilicochromium, ferrosilicon, ferrosilicomanganese, ferromanganese
  • ISO 4552-2:1987 Part 2: Ferrotitanium, ferromolybdenum, ferrotungsten, ferroniobium, ferrovanadium
• ISO 4578 Adhesives — Determination of peel resistance of high-strength adhesive bonds — Floating-roller method
• ISO 4582 Plastics — Determination of changes in colour and variations in properties after exposure to daylight under glass, natural weathering or laboratory light sources
• ISO 4587 Adhesives — Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies
• ISO 4618:2014 Paints and varnishes – Terms and definitions
• ISO 4628 Paints and varnishes – Evaluation of degradation of coatings – Designation of quantity and size of defects, and of intensity of uniform changes in appearance
  • ISO 4628-1 General introduction and designation system
  • ISO 4628-2 Assessment of degree of blistering
  • ISO 4628-3 Assessment of degree of rusting
  • ISO 4628-4 Assessment of degree of cracking
  • ISO 4628-5 Assessment of degree of flaking
  • ISO 4628-6 Assessment of degree of chalking by tape method
  • ISO 4628-7 Assessment of degree of chalking by velvet method
  • ISO 4628-8 Assessment of degree of delamination and corrosion around a scribe
  • ISO 4628-10 Assessment of degree of filiform corrosion
• ISO 4648:1991 Rubber, vulcanized or thermoplastic — Determination of dimensions of test pieces and products for test purposes [Withdrawn: replaced with ISO 23529]
• ISO 4661 Rubber, vulcanized — Preparation of samples and test pieces
  • ISO 4661-1:1993 Rubber, vulcanized or thermoplastic — Preparation of samples and test pieces — Part 1: Physical tests [Withdrawn: replaced with ISO 23529]
  • ISO 4661-2:2018 Rubber, vulcanized — Preparation of samples and test pieces — Part 2: Chemical tests
• ISO 4683 Raw sheep skins
  • ISO 4683-1:1998 Part 1: Descriptions of defects
• ISO 4720:2009 Essential oils – Nomenclature
• ISO 4730:2017 Essential oil of Melaleuca, terpinen-4-ol type (Tea Tree oil)
• ISO 4786:1977 Enclosed-scale adjustable-range thermometers
• ISO 4787:2010 Laboratory glassware – Volumetric instruments – Methods for testing of capacity and for use
• ISO 4788:2005 Laboratory glassware – Graduated measuring cylinders
• ISO 4791 Laboratory apparatus – Vocabulary relating to apparatus made essentially from glass, porcelain or vitreous silica
  • ISO 4791-1:1985 Part 1: Names for items of apparatus
• ISO 4795:1996 Glass for thermometer bulbs
• ISO 4801:1979 Glass alcoholometers and alcohol hydrometers not incorporating a thermometer
• ISO 4805:1982 Laboratory glassware – Thermo-alcoholometers and alcohol-thermohydrometers
• ISO 4824:1993 Dentistry — Ceramic denture teeth [Withdrawn: replaced with ISO 22112]
• ISO 4831:2006 Microbiology of food and animal feeding stuffs – Horizontal method for the detection and enumeration of coliforms – Most probable number technique
• ISO 4832:2006 Microbiology of food and animal feeding stuffs – Horizontal method for the enumeration of coliforms – Colony-count technique
• ISO 4833 Microbiology of the food chain – Horizontal method for the enumeration of microorganisms
  • ISO 4833-1:2013 Part 1: Colony count at 30 degrees C by the pour plate technique
  • ISO 4833-2:2013 Part 2: Colony count at 30 degrees C by the surface plating technique
• ISO 4848:1980 Concrete — Determination of air content of freshly mixed concrete — Pressure method [Withdrawn: replaced with ISO 1920-2]
• ISO 4858:1982 Wood — Determination of volumetric shrinkage [Withdrawn: replaced with ISO 13061-14]
• ISO 4859:1982 Wood — Determination of radial and tangential swelling [Withdrawn: replaced with ISO 13061-15]
• ISO 4860:1982 Wood — Determination of volumetric swelling [Withdrawn: replaced with ISO 13061-16]
• ISO 4866:2010 Mechanical vibration and shock – Vibration of fixed structures – Guidelines for the measurement of vibrations and evaluation of their effects on structures
• ISO 4871:1996 Acoustics – Declaration and verification of noise emission values of machinery and equipment
• ISO/IEC 4873:1991 Information technology – ISO 8-bit code for information interchange – Structure and rules for implementation
• ISO 4875 Metal-cutting band saw blades
  • ISO 4875-1:2006 Part 1: Vocabulary
• ISO 4880:1997 Burning behaviour of textiles and textile products – Vocabulary
• ISO 4882:1979 Office machines and data processing equipment – Line spacings and character spacings
• ISO 4885:2017 Ferrous materials – Heat treatments – Vocabulary
• ISO 4892 Plastics – Methods of exposure to laboratory light sources
• ISO 4902:1989 Information technology – Data communication – 37-pole DTE/DCE interface connector and contact number assignments
• ISO 4903:1989 Information technology – Data communication – 15-pole DTE/DCE interface connector and contact number assignments
• ISO/IEC 4909:2006 Identification cards – Financial transaction cards – Magnetic stripe data content for track 3
• ISO 4921:2000 Knitting – Basic concepts – Vocabulary
• ISO 4977 Double cold-reduced electrolytic tinplate
  • ISO 4977-1:1984 Part 1: Sheet [Withdrawn: replaced with ISO 11949]
  • ISO 4977-2:1984 Part 2: Coil for subsequent cutting into sheets [Withdrawn: replaced with ISO 11949]

External links

• International Organization for Standardization
• ISO Certification Provider
• ISO Consultant