List of ISO standards 1–1999
This is a list of published[Note 1] International Organization for Standardization (ISO) standards and other deliverables.[Note 2] For a complete and up-to-date list of all the ISO standards, see the ISO catalogue.[1]
The standards are protected by copyright and most of them must be purchased. However, about 300 of the standards produced by ISO and IEC's Joint Technical Committee 1 (JTC1) have been made freely and publicly available.[2]
ISO 1 – ISO 99
- ISO 1:2016 Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties
- ISO 2:1973 Textiles — Designation of the direction of twist in yarns and related products
- ISO 3:1973 Preferred numbers — Series of preferred numbers
- ISO 4:1997 Information and documentation — Rules for the abbreviation of title words and titles of publications
- ISO 5 Photography and graphic technology — Density measurements
- ISO 6:1993 Photography — Black-and-white pictorial still camera negative film/process systems — Determination of ISO speed
- ISO 7 Pipe threads where pressure-tight joints are made on the threads
- ISO 8:2019 Information and documentation — Presentation and identification of periodicals
- ISO 9:1995 Information and documentation — Transliteration of Cyrillic characters into Latin characters — Slavic and non-Slavic languages
- ISO/R 10:1955 Aircraft — Ground air-conditioning connections for pressure cabins [Withdrawn: replaced with ISO 1034]
- ISO 11:1987 Aircraft — Ground pressure testing connections for pressure cabins
- ISO 12:1987 Aerospace — Pipelines — Identification
- ISO 13:1978 Grey iron pipes, special castings and grey iron parts for pressure main lines [Withdrawn without replacement]
- ISO 14:1982 Straight-sided splines for cylindrical shafts with internal centering — Dimensions, tolerances and verification
- ISO 15:2017 Rolling bearings — Radial bearings — Boundary dimensions, general plan
- ISO 16:1975 Acoustics — Standard tuning frequency (Standard musical pitch)
- ISO 17:1973 Guide to the use of preferred numbers and of series of preferred numbers
- ISO 18:1981 Documentation — Contents list of periodicals
- ISO 21:1985 Shipbuilding — Inland navigation — Cable-lifters for stud-link anchor chains [Withdrawn without replacement]
- ISO 22:1991 Belt drives — Flat transmission belts and corresponding pulleys — Dimensions and tolerances
- ISO 23:1993 Cinematography — Camera usage of 35 mm motion-picture film — Specifications
- ISO/R 24:1956 Cinematography — Projector usage of 35 mm motion — picture films for direct front projection — Specifications [Withdrawn: replaced with ISO 2939]
- ISO 25:1994 Cinematography — Camera usage of 16 mm motion-picture film — Specifications
- ISO 26:1993 Cinematography — Projector usage of 16 mm motion-picture films for direct front projection — Specifications
- ISO 28:1976 Cinematography — Camera usage of 8 mm Type R motion-picture film — Specifications
- ISO 29:1980 Cinematography — Projector usage of 8 mm Type R silent motion-picture film for direct front projection — Specifications [Withdrawn without replacement]
- ISO/R 30:1956 Bibliographical strip [Withdrawn without replacement]
- ISO 31 Quantities and units [Withdrawn: replaced with ISO/IEC 80000]
- ISO 32:1977 Gas cylinders for medical use — Marking for identification of content
- ISO 34 Rubber, vulcanized or thermoplastic — Determination of tear strength
- ISO 34-1:2015 Part 1: Trouser, angle and crescent test pieces
- ISO 34-2:2015 Part 2: Small (Delft) test pieces
- ISO 35:2004 Natural rubber latex concentrate — Determination of mechanical stability
- ISO 36:2020 Rubber, vulcanized or thermoplastic — Determination of adhesion to textile fabrics
- ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
- ISO 41:1980 Shipbuilding — Inland vessels — Covers for deck openings for pumps [Withdrawn without replacement]
- ISO/R 42:1957 Shipbuilding — Inland vessels — Mushroom-type ventilator heads [Withdrawn: replaced by ISO 3372, now withdrawn without replacement]
- ISO 43:2016 Aircraft — Jacking pads
- ISO 44:1975 Aerospace — Lever-operated, two-position, ON/OFF switches — Directions of operation
- ISO 45:1990 Aircraft — Pressure refuelling connections
- ISO 46:1973 Aircraft — Fuel nozzle grounding plugs and sockets
- ISO/R 47:1957 Aircraft — Toilet connections [Withdrawn: replaced with ISO 450, later ISO 17775]
- ISO 48 Rubber, vulcanized or thermoplastic — Determination of hardness
- ISO 48-1:2018 Part 1: Introduction and guidance
- ISO 48-2:2018 Part 2: Hardness between 10 IRHD and 100 IRHD
- ISO 48-3:2018 Part 3: Dead-load hardness using the very low rubber hardness (VLRH) scale
- ISO 48-4:2018 Part 4: Indentation hardness by durometer method (Shore hardness)
- ISO 48-5:2018 Part 5: Indentation hardness by IRHD pocket meter method
- ISO 48-6:2018 Part 6: Apparent hardness of rubber-covered rollers by IRHD method
- ISO 48-7:2018 Part 7: Apparent hardness of rubber-covered rollers by Shore-type durometer method
- ISO 48-8:2018 Part 8: Apparent hardness of rubber-covered rollers by Pusey and Jones method
- ISO 48-9:2018 Part 9: Calibration and verification of hardness testers
- ISO 49:1994 Malleable cast iron fittings threaded to ISO 7-1
- ISO 50:1977 Metal pipes — Steel sockets screwed according to ISO 7 [Withdrawn without replacement]
- ISO 53:1998 Cylindrical gears for general and heavy engineering — Standard basic rack tooth profile
- ISO 54:1996 Cylindrical gears for general engineering and for heavy engineering — Modules
- ISO 55:1977 Seedlac — Specification [Withdrawn without replacement]
- ISO 56:1979 Shellac — Specification [Withdrawn without replacement]
- ISO 56-1:1979 Hand-made Shellac — Specification [Withdrawn without replacement]
- ISO 56-2:1979 Machine-made Shellac — Specification [Withdrawn without replacement]
- ISO 57:1975 Bleached lac — Specification [Withdrawn without replacement]
- ISO/R 58:1958 Substances of paper [Withdrawn without replacement]
- ISO 59:1976 Plastics — Determination of acetone-soluble matter [Withdrawn without replacement]
- ISO 60:1977 Plastics — Determination of apparent density of material that can be poured from a specified funnel
- ISO 61:1976 Plastics — Determination of apparent density of moulding material that cannot be poured from a specified funnel
- ISO 62:2008 Plastics — Determination of water absorption
- ISO 63:1975 Flat transmission belts — Lengths [Withdrawn: Replaced with ISO 22]
- ISO 64:1974 Carbon steel tubes — Lengths [Withdrawn: Replaced with ISO 4200:1991]
- ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1
- ISO/R 66:1958 Paper vocabulary — First series of terms [Withdrawn: Replaced with ISO 4046]
- ISO 67:1981 Muscovite mica blocks, thins and films — Grading by size [Withdrawn without replacement]
- ISO 68 ISO general-purpose screw threads – Basic profile
- ISO 68-1:1998 Part 1: Metric screw threads
- ISO 68-2:1998 Part 2: Inch screw threads
- ISO 69:1998 Cinematography — 16 mm motion-picture and magnetic film — Cutting and perforating dimensions
- ISO 70:1981 Cinematography — 35 mm negative photographic sound record on 35 mm motion-picture film — Position and maximum width dimensions
- ISO 71:2014 Cinematography — 16 mm negative photographic sound record on 16 mm, 35/16 mm and 35/32 mm motion-picture film—Positions and dimensions
- ISO/R 73:1958 Cinematography — Image area produced by camera aperture on 35 mm motion-picture film — Positions and dimensions [Withdrawn: replaced by ISO 2906 and ISO 2907]
- ISO 74:1976 Cinematography — Image area produced by camera aperture and maximum projectable image area on 8 mm Type R motion-picture film — Positions and dimensions
- ISO 75 Plastics — Determination of temperature of deflection under load
- ISO 75-1:2020 Part 1: General test method
- ISO 75-2:2013 Part 2: Plastics and ebonite
- ISO 75-3:2004 Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
- ISO 76:2006 Rolling bearings — Static load ratings
- ISO 78 Chemistry — Layouts for standards[Note 3]
- ISO 78-2:1999 Part 2: Methods of chemical analysis
- ISO 78-3:1983 Part 3: Standard for molecular absorption spectrometry [Withdrawn without replacement]
- ISO 78-4:1983 Part 4: Standard for atomic absorption spectrometric analysis [Withdrawn without replacement]
- ISO/TR 79:2015 Reference materials - Examples of reference materials for qualitative properties
- ISO/R 80:1968 Rockwell hardness test (B and C scales) for steel [Withdrawn: replaced with ISO 6508]
- ISO/R 81:1967 Vickers hardness test for steel (Load 5 to 100 kgf) [Withdrawn: replaced with ISO 6507-1]
- ISO 82:1974 Steel — Tensile testing [Withdrawn: replaced with ISO 6892-1]
- ISO 83:1976 Steel — Charpy impact test (U-notch) [Withdrawn: replaced with ISO 148-1]
- ISO/R 84:1959 Izod impact test for steel [Withdrawn without replacement]
- ISO/R 85:1959 Bend test for steel [Withdrawn: replaced with ISO 7438]
- ISO 86:1974 Steel — Tensile testing of sheet and strip less than 3 mm and not less than 0,5 mm thick [Withdrawn: replaced with ISO 6892-1]
- ISO/R 87:1959 Simple bend testing of steel sheet and strip less than 3 mm thick [Withdrawn: replaced with ISO 7438]
- ISO/R 88:1959 Reverse bend testing of steel sheet and strip less than 3 mm thick [Withdrawn: replaced with ISO 7799]
- ISO 89:1974 Steel — Tensile testing of wire [Withdrawn: replaced with ISO 6892-1]
- ISO 90 Light gauge metal containers — Definitions and determination of dimensions and capacities
- ISO 90-1:1997 Part 1: Open-top cans
- ISO 90-2:1997 Part 2: General use containers
- ISO 90-3:2000 Part 3: Aerosol cans
- ISO 91:2017 Petroleum and related products — Temperature and pressure volume correction factors (petroleum measurement tables) and standard reference conditions
- ISO 92:1976 Textile machinery and accessories — Spinning machinery — Definition of side (left or right)
- ISO 93 Textile machinery and accessories — Cylindrical sliver cans
- ISO 93-1:2006 Part 1: Main dimensions
- ISO 93-2:2006 Part 2: Spring bottoms
- ISO 93-3:1981 Part 3: Packaging sliver cans (press cans) [Withdrawn without replacement]
- ISO 94:1982 Textile machinery and accessories — Spindle gauges for ring-spinning and ring-doubling frames
- ISO 96 Textile machinery and accessories — Rings and travellers for ring spinning and ring twisting frames
- ISO 96-1:2016 Part 1: Flange rings T and SF and their travellers
- ISO 96-2:2009 Part 2: HZ- and J-rings and their travellers
- ISO 97:1975 Textile machinery and accessories — Rings for spinning, doubling and twisting for ear-shaped travellers [Withdrawn: replaced with ISO 96-2]
- ISO 98:2001 Textile machinery and accessories — Spinning preparatory and spinning machinery — Main dimensions of coverings for top rollers
- ISO 99:1975 Pulleys for flat transmission belts — Diameters [Withdrawn: Replaced with ISO 22]
ISO 100 – ISO 199
- ISO 100:1984 Pulleys for flat transmission belts — Crowns [Withdrawn: replaced with ISO 22]
- ISO/R 101:1959 Width of sheets of paper [Withdrawn without replacement]
- ISO 102:1990 Aircraft — Gravity filling orifices
- ISO 104:2015 Rolling bearings — Thrust bearings — Boundary dimensions, general plan
- ISO 105 Textiles — Tests for colour fastness
- ISO 105-A01:2010 Part A01: General principles of testing
- ISO 105-A02:1993 Part A02: Grey scale for assessing change in colour
- ISO 105-A03:2019 Part A03: Grey scale for assessing staining
- ISO 105-A04:1989 Part A04: Method for the instrumental assessment of the degree of staining of adjacent fabrics
- ISO 105-A05:1996 Part A05: Instrumental assessment of change in colour for determination of grey scale rating
- ISO 105-A06:1995 Part A06: Instrumental determination of 1/1 standard depth of colour
- ISO 105-A08:2001 Part A08: Vocabulary used in colour measurement
- ISO 105-A11:2012 Part A11: Determination of colour fastness grades by digital imaging techniques
- ISO 105-B01:2014 Part B01: Colour fastness to light: Daylight
- ISO 105-B02:2014 Part B02: Colour fastness to artificial light: Xenon arc fading lamp test
- ISO 105-B03:2017 Part B03: Colour fastness to weathering: Outdoor exposure
- ISO 105-B04:1994 Part B04: Colour fastness to artificial weathering: Xenon arc fading lamp test
- ISO 105-B05:1993 Part B05: Detection and assessment of photochromism
- ISO 105-B06:2020 Part B06: Colour fastness and ageing to artificial light at high temperatures: Xenon arc fading lamp test
- ISO 105-B07:2009 Part B07: Colour fastness to light of textiles wetted with artificial perspiration
- ISO 105-B08:1995 Part B08: Quality control of blue wool reference materials 1 to 7
- ISO 105-B10:2011 Part B10: Artificial weathering — Exposure to filtered xenon-arc radiation
- ISO 105-C01:1989 Part C01: Colour fastness to washing: Test 1 [Withdrawn: replaced with ISO 105-C10]
- ISO 105-C02:1989 Part C02: Colour fastness to washing: Test 2 [Withdrawn: replaced with ISO 105-C10]
- ISO 105-C03:1989 Part C03: Colour fastness to washing: Test 3 [Withdrawn: replaced with ISO 105-C10]
- ISO 105-C04:1989 Part C04: Colour fastness to washing: Test 4 [Withdrawn: replaced with ISO 105-C10]
- ISO 105-C05:1989 Part C05: Colour fastness to washing: Test 5 [Withdrawn: replaced with ISO 105-C10]
- ISO 105-C06:2010 Part C06: Colour fastness to domestic and commercial laundering
- ISO 105-C07:1999 Part C07: Colour fastness to wet scrubbing of pigment printed textiles
- ISO 105-C08:2010 Part C08: Colour fastness to domestic and commercial laundering using a non-phosphate reference detergent incorporating a low-temperature bleach activator
- ISO 105-C09:2001 Part C09: Colour fastness to domestic and commercial laundering — Oxidative bleach response using a non-phosphate reference detergent incorporating a low temperature bleach activator
- ISO 105-C10:2006 Part C10: Colour fastness to washing with soap or soap and soda
- ISO 105-C12:2004 Part C12: Colour fastness to industrial laundering
- ISO 105-D01:2010 Part D01: Colour fastness to drycleaning using perchloroethylene solvent
- ISO 105-D02:2016 Part D02: Colour fastness to rubbing: Organic solvents
- ISO 105-E01:2013 Part E01: Colour fastness to water
- ISO 105-E02:2013 Part E02: Colour fastness to sea water
- ISO 105-E03:2010 Part E03: Colour fastness to chlorinated water (swimming-pool water)
- ISO 105-E04:2013 Part E04: Colour fastness to perspiration
- ISO 105-E05:2010 Part E05: Colour fastness to spotting: Acid
- ISO 105-E06:2006 Part E06: Colour fastness to spotting: Alkali
- ISO 105-E07:2010 Part E07: Colour fastness to spotting: Water
- ISO 105-E08:1994 Part E08: Colour fastness to hot water
- ISO 105-E09:2010 Part E09: Colour fastness to potting
- ISO 105-E10:1994 Part E10: Colour fastness to decatizing
- ISO 105-E11:1994 Part E11: Colour fastness to steaming
- ISO 105-E12:2010 Part E12: Colour fastness to milling: Alkaline milling
- ISO 105-E13:1994 Part E13: Colour fastness to acid-felting: Severe
- ISO 105-E14:1994 Part E14: Colour fastness to acid-felting: Mild
- ISO 105-E16:2006 Part E16: Colour fastness to water spotting on upholstery fabrics
- ISO 105-F01:2001 Part F01: Specification for wool adjacent fabric
- ISO 105-F02:2009 Part F02: Specification for cotton and viscose adjacent fabrics
- ISO 105-F03:2001 Part F03: Specification for polyamide adjacent fabric
- ISO 105-F04:2001 Part F04: Specification for polyester adjacent fabric
- ISO 105-F05:2001 Part F05: Specification for acrylic adjacent fabric
- ISO 105-F06:2000 Part F06: Specification for silk adjacent fabric
- ISO 105-F07:2001 Part F07: Specification for secondary acetate adjacent fabric
- ISO 105-F09:2009 Part F09: Specification for cotton rubbing cloth
- ISO 105-F10:1989 Part F10: Specification for adjacent fabric: Multifibre
- ISO 105-G01:2016 Part G01: Colour fastness to nitrogen oxides
- ISO 105-G02:1993 Part G02: Colour fastness to burnt-gas fumes
- ISO 105-G03:1993 Part G03: Colour fastness to ozone in the atmosphere
- ISO 105-G04:2016 Part G04: Colour fastness to oxides of nitrogen in the atmosphere at high humidities
- ISO 105-J01:1997 Part J01: General principles for measurement of surface colour
- ISO 105-J02:1997 Part J02: Instrumental assessment of relative whiteness
- ISO 105-J03:2009 Part J03: Calculation of colour differences
- ISO 105-J05:2007 Part J05: Method for the instrumental assessment of the colour inconstancy of a specimen with change in illuminant (CMCCON02)
- ISO 105-N01:1993 Part N01: Colour fastness to bleaching: Hypochlorite
- ISO 105-N02:1993 Part N02: Colour fastness to bleaching: Peroxide
- ISO 105-N03:1993 Part N03: Colour fastness to bleaching: Sodium chlorite (mild)
- ISO 105-N04:1993 Part N04: Colour fastness to bleaching: Sodium chlorite (severe)
- ISO 105-N05:1993 Part N05: Colour fastness to stoving
- ISO 105-P01:1993 Part P01: Colour fastness to dry heat (excluding pressing)
- ISO 105-P02:2002 Part P02: Colour fastness to pleating: Steam pleating
- ISO 105-S01:1993 Part S01: Colour fastness to vulcanization: Hot air
- ISO 105-S02:1993 Part S02: Colour fastness to vulcanization: Sulfur monochloride
- ISO 105-S03:1993 Part S03: Colour fastness to vulcanization: Open steam
- ISO 105-X01:1993 Part X01: Colour fastness to carbonizing: Aluminium chloride
- ISO 105-X02:1993 Part X02: Colour fastness to carbonizing: Sulfuric acid
- ISO 105-X03:1987 Part X03: Colour fastness to chlorination [Withdrawn without replacement]
- ISO 105-X04:1994 Part X04: Colour fastness to mercerizing
- ISO 105-X05:1994 Part X05: Colour fastness to organic solvents
- ISO 105-X06:1994 Part X06: Colour fastness to soda boiling
- ISO 105-X07:1994 Part X07: Colour fastness to cross-dyeing: Wool
- ISO 105-X08:1994 Part X08: Colour fastness to degumming
- ISO 105-X09:1993 Part X09: Colour fastness to formaldehyde
- ISO 105-X10:1993 Part X10: Assessment of migration of textile colours into polyvinyl chloride coatings
- ISO 105-X11:1994 Part X11: Colour fastness to hot pressing
- ISO 105-X12:2016 Part X12: Colour fastness to rubbing
- ISO 105-X13:1994 Part X13: Colour fastness of wool dyes to processes using chemical means for creasing, pleating and setting
- ISO 105-X14:1994 Part X14: Colour fastness to acid chlorination of wool: Sodium dichloroisocyanurate
- ISO 105-X16:2016 Part X16: Colour fastness to rubbing — Small areas
- ISO 105-X18:2007 Part X18: Assessment of the potential to phenolic yellowing of materials
- ISO 105-X19:2020 Part X19: Colour fastness to rubbing (Gakushin test method)
- ISO 105-Z01:1993 Part Z01: Colour fastness to metals in the dye-bath: Chromium salts
- ISO 105-Z02:1993 Part Z02: Colour fastness to metals in the dye-bath: Iron and copper
- ISO 105-Z03:1996 Part Z03: Intercompatibility of basic dyes for acrylic fibres
- ISO 105-Z04:1995 Part Z04: Dispersibility of disperse dyes
- ISO 105-Z05:1996 Part Z05: Determination of the dusting behaviour of dyes
- ISO 105-Z06:1998 Part Z06: Evaluation of dye and pigment migration
- ISO 105-Z07:1995 Part Z07: Determination of application solubility and solution stability of water-soluble dyes
- ISO 105-Z08:1995 Part Z08: Determination of solubility and solution stability of reactive dyes in the presence of electrolytes
- ISO 105-Z09:1995 Part Z09: Determination of cold water solubility of water-soluble dyes
- ISO 105-Z10:1997 Part Z10: Determination of relative colour strength of dyes in solution
- ISO 105-Z11:1998 Part Z11: Evaluation of speckiness of colorant dispersions
- ISO 108:1976 Textile machinery and accessories — Weaving looms — Definition of left and right sides
- ISO 109:1982 Textile machinery — Working widths of weaving machines
- ISO 110:1978 Textile machinery and accessories — Cones for yarn winding (cross wound) — Half angle of the cone 9 degrees 15' [Withdrawn without replacement]
- ISO 111:1978 Textile machinery and accessories — Cones for yarn winding (cross wound) — Half angle of the cone 4 degrees 20' [Withdrawn: Replaced with ISO 8489-3]
- ISO 112:1983 Textile machinery and accessories — Cones for yarn winding (cross wound) — Half angle of the cone 3 degrees 30' [Withdrawn: Replaced with ISO 8489-2]
- ISO 113:2010 Rolling bearings — Plummer block housings — Boundary dimensions
- ISO 114:1980 99.8 Unalloyed magnesium ingots — Chemical composition [Withdrawn: Replaced by ISO 8287]
- ISO 115:2003 Unalloyed aluminium ingots for remelting — Classification and composition
- ISO/R 117:1959 Plastics — Phenol-formaldehyde mouldings — Determination of water absorption [Withdrawn: replaced by ISO 62]
- ISO 119:1977 Plastics — Phenol-formaldehyde mouldings — Determination of free phenols — Iodometric method
- ISO 120:1977 Plastics — Phenol-formaldehyde mouldings — Determination of free ammonia and ammonium compounds — Colorimetric comparison method
- ISO 121:1980 Magnesium-aluminium-zinc alloy ingots and alloy castings — Chemical composition and mechanical properties of sand cast reference test bars [Withdrawn: replaced by ISO 16220]
- ISO/R 122:1959 Composition of magnesium-aluminium-zinc alloy ingots for casting purposes [Withdrawn: replaced by ISO 121, and later ISO 16220]
- ISO 123:2001 Rubber latex — Sampling
- ISO 124:2014 Latex, rubber — Determination of total solids content
- ISO 125:2020 Natural rubber latex concentrate — Determination of alkalinity
- ISO 126:2005 Natural rubber latex concentrate — Determination of dry rubber content
- ISO 127:2018 Rubber, natural latex concentrate — Determination of KOH number
- ISO 128 Technical product documentation — General principles of representation[Note 3]
- ISO 129 Technical product documentation — Indication of dimensions and tolerances[Note 3]
- ISO 129-1:2018 Part 1: General principles
- ISO 129-4:2013 Part 4: Dimensioning of shipbuilding drawings
- ISO 129-5:2018 Part 5: Dimensioning of structural metal work
- ISO 131:1979 Acoustics — Expression of physical and subjective magnitudes of sound or noise in air [Withdrawn without replacement]
- ISO 132:2017 Rubber, vulcanized or thermoplastic — Determination of flex cracking and crack growth (De Mattia)
- ISO 133:1983 Rubber, vulcanized — Determination of crack growth (De Mattia) [Withdrawn: Replaced with ISO 132]
- ISO 134:1973 Steel — Determination of crack growth [Withdrawn: Replaced with ISO 4200:1991]
- ISO/R 135:1959 Paper vocabulary — Second series of terms [Withdrawn: Replaced with ISO 4046]
- ISO 136:1972 Steel — Simple torsion testing of wire [Withdrawn: replaced by ISO 7800]
- ISO 137:2015 Wool — Determination of fibre diameter — Projection microscope method
- ISO 139:2005 Textiles — Standard atmospheres for conditioning and testing
- ISO 140 Acoustics — Measurement of sound insulation in buildings and of building elements
- ISO 140-1:1997 Part 1: Requirements for laboratory test facilities with suppressed flanking transmission [Withdrawn: replaced by ISO 10140-(1-5)]
- ISO 140-2:1991 Part 2: Determination, verification and application of precision data [Withdrawn: replaced by ISO 12999-1:2014]
- ISO 140-3:1995 Part 3: Laboratory measurements of airborne sound insulation of building elements [Withdrawn: replaced by ISO 10140-(1-5)]
- ISO 140-4:1998 Part 4: Field measurements of airborne sound insulation between rooms [Withdrawn: replaced by ISO 16283-1:2014]
- ISO 140-5:1998 Part 5: Field measurements of airborne sound insulation of façade elements and façades [Withdrawn: replaced by ISO 16283-(1,3):2014]
- ISO 140-6:1998 Part 6: Laboratory measurements of impact sound insulation of floors [Withdrawn: replaced by ISO 10140-(1-5)]
- ISO 140-7:1998 Part 7: Field measurements of impact sound insulation of floors [Withdrawn: replaced by ISO 16283-(1-2)]
- ISO 140-8:1997 Part 8: Laboratory measurements of the reduction of transmitted impact noise by floor coverings on a heavyweight standard floor [Withdrawn: replaced by ISO 10140-(1-5)]
- ISO 140-9:1985 Part 9: Laboratory measurement of room-to-room airborne sound insulation of a suspended ceiling with a plenum above it [Withdrawn: replaced by ISO 10848-2]
- ISO 140-10:1991 Part 10: Laboratory measurement of airborne sound insulation of small building elements [Withdrawn: replaced by ISO 10140-(1-5)]
- ISO 140-11:1991 Part 11: Laboratory measurements of the reduction of transmitted impact sound by floor coverings on lightweight reference floors [Withdrawn: replaced by ISO 10140-(1-5)]
- ISO 140-12:2000 Part 12: Laboratory measurement of room-to-room airborne and impact sound insulation of an access floor [Withdrawn: replaced by ISO 10848-2]
- ISO/TR 140-13:1997 Part 13: Guidelines [Withdrawn: replaced by ISO 140-14]
- ISO 140-14:2004 Part 14: Guidelines for special situations in the field [Withdrawn: replaced by ISO 16283-1:2014]
- ISO 140-16:2006 Part 16: Laboratory measurement of the sound reduction index improvement by additional lining [Withdrawn: replaced by ISO 10140-(1-5)]
- ISO 140-18:2006 Part 18: Laboratory measurement of sound generated by rainfall on building elements [Withdrawn: replaced by ISO 10140-(1,5):2016]
- ISO 141:1976 Textile machinery and accessories — Pirn winders and cross winders — Definition of left and right sides
- ISO 142:1976 Textile machinery and accessories — Weaving preparatory machines — Definition of left and right sides
- ISO 143:1977 Textile machinery and accessories — Weft pirns for automatic looms [Withdrawn without replacement]
- ISO 144:1973 Steel — Reverse bend testing of wire [Withdrawn: replaced with ISO 7801]
- ISO/R 145:1960 Steel — Wrapping test for wire [Withdrawn: replaced with ISO 7802]
- ISO 146:1984 Metallic materials — Hardness test — Verification of Vickers hardness testing machines HV 0,2 to HV 100 [Withdrawn: replaced with ISO 6507-2]
- ISO 146-2:1993 Metallic materials — Verification of Vickers hardness testing machines — Part 2: Less than HV 0,2 [Withdrawn: replaced with ISO 6507-2]
- ISO/R 147:1960 Load calibration of testing machines for tensile testing of steel [Withdrawn: replaced with ISO 7500-1]
- ISO 148 Metallic materials — Charpy pendulum impact test
- ISO 148-1:2016 Part 1: Test method
- ISO 148-2:2016 Part 2: Verification of testing machines
- ISO 148-3:2016 Part 3: Preparation and characterization of Charpy V-notch test pieces for indirect verification of pendulum impact machines
- ISO/R 149:1960 Modified Erichsen cupping test for steel sheet and strip [Withdrawn: replaced with ISO 8490]
- ISO 150:2018 Raw, refined and boiled linseed oil for paints and varnishes — Specifications and methods of test
- ISO/R 154: Shipbuilding details — Marking of rolled, drawn and extruded products in light metals or in light alloys [Withdrawn without replacement]
- ISO 155:2019 Belt drives — Pulleys — Limiting values for adjustment of centres
- ISO 156:1982 Metallic materials — Hardness test — Verification of Brinell hardness testing machines [Withdrawn: replaced by ISO 6506-2]
- ISO 157:1996 Coal — Determination of forms of sulfur
- ISO/R 158:1960 Coal — Determination of ash [Withdrawn: replaced by ISO 1171]
- ISO 160:1980 Asbestos-cement pressure pipes and joints [Withdrawn without replacement]
- ISO 161 Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures
- ISO 161-1:2018 Part 1: Metric series
- ISO 161-2:1996 Part 2: Inch-based series
- ISO 162:1985 Cinematography — Head gaps and sound records for three-, four-, or six-track magnetic sound records on 35 mm and single-track on 17,5 mm motion-picture film containing no picture — Positions and width dimensions
- ISO/R 164:1960 Composition of aluminium alloy castings [Withdrawn: replaced by ISO 3522]
- ISO/R 165:1960 Flanging test on steel tubes [Withdrawn: replaced by ISO 8494]
- ISO/R 166:1960 Drift expanding test on steel tubes [Withdrawn: replaced by ISO 8493]
- ISO/R 167:1960 Bend test on steel tubes [Withdrawn: replaced by ISO 8491]
- ISO/R 169:1960 Sizes of photocopies (on paper) readable without optical devices [Withdrawn without replacement]
- ISO 171:1980 Plastics — Determination of bulk factor of moulding materials
- ISO 172:1978 Plastics — Phenol-formaldehyde mouldings — Detection of free ammonia
- ISO 174:1974 Plastics — Homopolymer and copolymer resins of vinyl chloride — Determination of viscosity number in dilute solution [Withdrawn replaced by ISO 1628-2]
- ISO 175:2010 Plastics — Methods of test for the determination of the effects of immersion in liquid chemicals
- ISO 176:2005 Plastics — Determination of loss of plasticizers — Activated carbon method
- ISO 177:2016 Plastics — Determination of migration of plasticizers
- ISO 178:2019 Plastics — Determination of flexural properties
- ISO 179 Plastics — Determination of Charpy impact properties
- ISO 179-1:2010 Part 1: Non-instrumented impact test
- ISO 179-2:2020 Part 2: Instrumented impact test
- ISO 180:2019 Plastics — Determination of Izod impact strength
- ISO 181:1981 Plastics — Determination of flammability characteristics of rigid plastics in the form of small specimens in contact with an incandescent rod [Withdrawn without replacement]
- ISO 182 Plastics — Determination of the tendency of compounds and products based on vinyl chloride homopolymers and copolymers to evolve hydrogen chloride and any other acidic products at elevated temperatures
- ISO 182-1:1990 Part 1: Congo red method
- ISO 182-2:1990 Part 2: pH method
- ISO 182-3:1993 Part 3: Conductometric method
- ISO 182-4:1993 Part 4: Potentiometric method
- ISO 183:1976 Plastics — Qualitative evaluation of the bleeding of colorants [Withdrawn without replacement]
- ISO/R 184:1961 Grey cast irons — Brinell hardness test [Withdrawn without replacement]
- ISO 185:2020 Grey cast irons — Classification
- ISO 186:2002 Paper and board — Sampling to determine average quality
- ISO 187:1990 Paper, board and pulps — Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples
- ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
- ISO 194:1981 Plastics — List of equivalent terms [Withdrawn: replaced by ISO 472:1988]
- ISO 196:1978 Wrought copper and copper alloys — Detection of residual stress — Mercury(I) nitrate test
- ISO 197 Copper and copper alloys — Terms and definitions
- ISO 197-1:1983 Part 1: Materials
- ISO 197-2:1983 Part 2: Unwrought products (Refinery shapes)
- ISO 197-3:1983 Part 3: Wrought products
- ISO 197-4:1983 Part 4: Castings
- ISO 197-5:1980 Part 5: Methods of processing and treatment
- ISO 199:2014 Rolling bearings — Thrust bearings — Geometrical product specification (GPS) and tolerance values
ISO 200 – ISO 999
- ISO 204:2018 Metallic materials — Uniaxial creep testing in tension — Method of test
- ISO 209:2007 Aluminium and aluminium alloys — Chemical composition
- ISO/TS 210:2014 Essential oils — General rules for packaging, conditioning and storage
- ISO/TS 211:2014 Essential oils — General rules for labelling and marking of containers
- ISO 212:2007 Essential oils — Sampling
- ISO 214:1976 Documentation — Abstracts for publications and documentation
- ISO 215:1986 Documentation — Presentation of contributions to periodicals and other serials
- ISO 216:2007 Writing paper and certain classes of printed matter — Trimmed sizes — A and B series, and indication of machine direction
- ISO 217:2013 Paper — Untrimmed sizes — Designation and tolerances for primary and supplementary ranges, and indication of machine direction
- ISO 225:2010 Fasteners — Bolts, screws, studs and nuts — Symbols and descriptions of dimensions
- ISO 226:2003 Acoustics — Normal equal-loudness-level contours
- ISO 228 Pipe threads where pressure-tight joints are not made on the threads
- ISO 229:1973 Machine tools — Speeds and feeds
- ISO 230 Test code for machine tools
- ISO 230-1:2012 Part 1: Geometric accuracy of machines operating under no-load or quasi-static conditions
- ISO 230-2:2014 Part 2: Determination of accuracy and repeatability of positioning of numerically controlled axes
- ISO 230-3:2020 Part 3: Determination of thermal effects
- ISO 230-4:2005 Part 4: Circular tests for numerically controlled machine tools
- ISO 230-5:2000 Part 5: Determination of the noise emission
- ISO 230-6:2002 Part 6: Determination of positioning accuracy on body and face diagonals (Diagonal displacement tests)
- ISO 230-7:2015 Part 7: Geometric accuracy of axes of rotation
- ISO/TR 230-8:2010 Part 8: Vibrations
- ISO/TR 230-9:2005 Part 9: Estimation of measurement uncertainty for machine tool tests according to series ISO 230, basic equations
- ISO 230-10:2016 Part 10: Determination of the measuring performance of probing systems of numerically controlled machine tools
- ISO/TR 230-11:2018 Part 11: Measuring instruments suitable for machine tool geometry tests
- ISO/R 231:1961 Paper vocabulary — Third series of terms [Withdrawn: Replaced with ISO 4046]
- ISO 233 Information and documentation — Transliteration of Arabic characters into Latin characters[Note 3]
- ISO 234 Files and rasps
- ISO 234-1:1983 Part 1: Dimensions
- ISO 234-2:1982 Part 2: Characteristics of cut
- ISO 235:2016 Parallel shank jobber and stub series drills and Morse taper shank drills
- ISO 236 Reamers[Note 3]
- ISO 236-1:1976 Hand reamers
- ISO 236-2:2013 Part 2: Long fluted machine reamers with Morse taper shanks
- ISO 237:1975 Rotating tools with parallel shanks — Diameters of shanks and sizes of driving squares
- ISO 238:2016 Reduction sleeves and extension sockets for tools with Morse taper shanks
- ISO 239:1999 Drill chuck tapers
- ISO 240:2016 Milling cutters — Interchangeability dimensions for cutter arbors or cutter mandrels
- ISO 241:1994 Shanks for turning and planing tools — Shapes and dimensions of the section
- ISO 242:2014 Carbide tips for brazing on turning tools
- ISO 243:2014 Turning tools with carbide tips — External tools
- ISO 244:1979 Aircraft — Sealing wire
- ISO 245:1998 Aerospace — Lockwire — Diameters
- ISO 246:2007 Rolling bearings — Cylindrical roller bearings, separate thrust collars — Boundary dimensions
- ISO 247 Rubber — Determination of ash
- ISO 247-1:2018 Part 1: Combustion method
- ISO 247-2:2018 Part 2: Thermogravimetric analysis (TGA)
- ISO 248 Rubber, raw - Determination of volatile-matter content
- ISO 248-1:2011 Part 1: Hot-mill method and oven method
- ISO 248-2:2019 Part 2: Thermogravimetric methods using an automatic analyser with an infrared drying unit
- ISO 249:2016 Rubber, raw natural — Determination of dirt content
- ISO 251:2012 Conveyor belts with textile carcass — Widths and lengths
- ISO 252:2007 Conveyor belts — Adhesion between constitutive elements — Test methods
- ISO 254:2011 Belt drives — Pulleys — Quality, finish and balance
- ISO 255:1990 Belt drives — Pulleys for V-belts (system based on datum width) — Geometrical inspection of grooves
- ISO 257:2018 Pesticides and other agrochemicals — Principles for the selection of common names
- ISO 259 Information and documentation — Transliteration of Hebrew characters into Latin characters[Note 3]
- ISO 261:1998 ISO general purpose metric screw threads — General plan
- ISO 262:1998 ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts
- ISO 263:1973 ISO inch screw threads — General plan and selection for screws, bolts and nuts — Diameter range 0,06 to 6 in
- ISO 265 Pipes and fittings of plastics materials — Fittings for domestic and industrial waste pipes — Basic dimensions: Metric series
- ISO 265-1:1988 Part 1: Unplasticized poly(vinyl chloride) (PVC-U)
- ISO 266:1997 Acoustics — Preferred frequencies
- ISO 268:1980 Aircraft — Mechanical and electromechanical indicators — General requirements
- ISO 269:1985 Correspondence envelopes - Designation and sizes [Withdrawn without replacement]
- ISO 272:1982 Fasteners — Hexagon products — Widths across flats
- ISO 273:1979 Fasteners — Clearance holes for bolts and screws
- ISO 276:2019 Binders for paints and varnishes — Linseed stand oil — Requirements and methods of test
- ISO 277:2002 Binders for paints and varnishes — Raw tung oil — Requirements and methods of test
- ISO 279:1998 Essential oils — Determination of relative density at 20 degrees C - Reference method
- ISO 280:1998 Essential oils — Determination of refractive index
- ISO 281:2007 Rolling bearings — Dynamic load ratings and rating life
- ISO 282:1992 Conveyor belts — Sampling
- ISO 283:2015 Textile conveyor belts — Full thickness tensile strength, elongation at break and elongation at the reference load — Test method
- ISO 284:2012 Conveyor belts - Electrical conductivity - Specification and test method
- ISO 286 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes
- ISO 287:2017 Paper and board — Determination of moisture content of a lot — Oven-drying method
- ISO 289 Rubber, unvulcanized — Determinations using a shearing-disc viscometer
- ISO 289-1:2015 Part 1: Determination of Mooney viscosity
- ISO 289-2:2020 Part 2: Determination of pre-vulcanization characteristics
- ISO 289-3:2015 Part 3: Determination of the Delta Mooney value for non-pigmented, oil-extended emulsion-polymerized SBR
- ISO 289-4:2003 Part 4: Determination of the Mooney stress-relaxation rate
- ISO 291:2008 Plastics — Standard atmospheres for conditioning and testing
- ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
- ISO 294 Plastics — Injection moulding of test specimens of thermoplastic materials
- ISO 294-1:2017 Part 1: General principles, and moulding of multipurpose and bar test specimens
- ISO 294-2:2018 Part 2: Small tensile bars
- ISO 294-3:2020 Part 3: Small plates
- ISO 294-4:2018 Part 4: Determination of moulding shrinkage
- ISO 294-5:2017 Part 5: Preparation of standard specimens for investigating anisotropy
- ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
- ISO 296:1991 Machine tools — Self-holding tapers for tool shanks
- ISO 297:1988 7/24 tapers for tool shanks for manual changing
- ISO 298:1973 Machine tools — Lathe centres — Sizes for interchangeability
- ISO 299:1987 Machine tool tables — T-slots and corresponding bolts
- ISO 301:2006 Zinc alloy ingots intended for castings
- ISO 302:2015 Pulps — Determination of Kappa number
- ISO 304:1985 Surface active agents — Determination of surface tension by drawing up liquid films
- ISO 305:2019 Plastics — Determination of thermal stability of poly(vinyl chloride), related chlorine-containing homopolymers and copolymers and their compounds — Discoloration method
- ISO 306:2013 Plastics — Thermoplastic materials - Determination of Vicat softening temperature (VST)
- ISO 307:2019 Plastics — Polyamides — Determination of viscosity number
- ISO 308:1994 Plastics — Phenolic moulding materials — Determination of acetone-soluble matter (apparent resin content of material in the unmoulded state)
- ISO 310:1992 Manganese ores and concentrates — Determination of hygroscopic moisture content in analytical samples — Gravimetric method
- ISO 312:1986 Manganese ores — Determination of active oxygen content, expressed as manganese dioxide — Titrimetric method
- ISO 315:1984 Manganese ores and concentrates — Determination of nickel content — Dimethylglyoxime spectrometric method and flame atomic absorption spectrometric method
- ISO 317:1984 Manganese ores and concentrates — Determination of arsenic content — Spectrometric method
- ISO 320:1981 Manganese ores — Determination of sulphur content — Barium sulphate gravimetric methods and sulphur dioxide titrimetric method after combustion
- ISO 334:2020 Coal and coke — Determination of total sulfur — Eschka method
- ISO 337:1981 Road vehicles — 50 semi-trailer fifth wheel coupling pin — Basic and mounting/interchangeability dimensions
- ISO 340:2013 Conveyor belts — Laboratory scale flammability characteristics — Requirements and test method
- ISO 344:1981 Textile machinery and accessories — Spinning machines — Flyer bobbins
- ISO 349:2020 Hard coal — Audibert-Arnu dilatometer test
- ISO 354:2003 Acoustics — Measurement of sound absorption in a reverberation room
- ISO 355:2019 Rolling bearings — Tapered roller bearings — Boundary dimensions and series designations
- ISO 356:1996 Essential oils — Preparation of test samples
- ISO 359:1983 Cinematography — Projectable image area on 16 mm motion-picture prints — Dimensions and location
- ISO 361:1975 Basic ionizing radiation symbol
- ISO 362 Measurement of noise emitted by accelerating road vehicles — Engineering method
- ISO 362-1:2015 Part 1: M and N categories
- ISO 362-2:2009 Part 2: L category
- ISO 362-3:2016 Part 3: Indoor testing M and N categories
- ISO 363 Textile machinery and accessories — Flat steel healds with closed end loops
- ISO 363-1:2006 Part 1: Dimensions of healds manufactured of rolled steel wire
- ISO 363-2:2006 Part 2: Dimensions of healds manufactured of hardened strip steel
- ISO 364:1983 Textile machinery and accessories — Twin wire healds for weaving machines with heald frames
- ISO 365:1982 Textile machinery and accessories — Twin wire healds with inset mail for Jacquard weaving
- ISO 366 Textile machinery and accessories — Reeds
- ISO 366-2:2009 Part 2: Dimensions and designation of metal reeds with plate baulk
- ISO 366-3:2009 Part 3: Dimensions and designation of metal reeds with double-spring baulk
- ISO 366-4:2005 Part 4: Dimensions and designation of plastic-bound metal reeds
- ISO 366-5:2006 Part 5: Dimensions and designation of profile capsules
- ISO 368:2017 Spinning preparatory, spinning and doubling (twisting) machinery — Tubes for ring-spinning, doubling and twisting spindles, taper 1:38 and 1:64
- ISO 369:2009 Machine tools — Symbols for indications appearing on machine tools
- ISO/R 372:1964 Paper vocabulary — Fourth series of terms [Withdrawn: Replaced with ISO 4046]
- ISO 374 Protective gloves against dangerous chemicals and micro-organisms
- ISO 374-1:2016 Part 1: Terminology and performance requirements for chemical risks
- ISO 374-2:2019 Part 2: Determination of resistance to penetration
- ISO 374-4:2019 Part 4: Determination of resistance to degradation by chemicals
- ISO 374-5:2016 Part 5: Terminology and performance requirements for micro-organisms risks
- ISO 376:2011 Metallic materials — Calibration of force-proving instruments used for the verification of uniaxial testing machines
- ISO 377:2017 Steel and steel products — Location and preparation of samples and test pieces for mechanical testing
- ISO 383:1976 Laboratory glassware — Interchangeable conical ground joints
- ISO 384:2015 Laboratory glass and plastics ware — Principles of design and construction of volumetric instruments
- ISO 385:2005 Laboratory glassware — Burettes
- ISO 386:1977 Liquid-in-glass laboratory thermometers — Principles of design, construction and use
- ISO 387:1977 Hydrometers — Principles of construction and adjustment
- ISO 389 Acoustics — Reference zero for the calibration of audiometric equipment
- ISO 389-1:2017 Part 1: Reference equivalent threshold sound pressure levels for pure tones and supra-aural earphones
- ISO 389-2:1994 Part 2: Reference equivalent threshold sound pressure levels for pure tones and insert earphones
- ISO 389-3:2016 Part 3: Reference equivalent threshold vibratory force levels for pure tones and bone vibrators
- ISO 389-4:1994 Part 4: Reference levels for narrow-band masking noise
- ISO 389-5:2006 Part 5: Reference equivalent threshold sound pressure levels for pure tones in the frequency range 8 kHz to 16 kHz
- ISO 389-6:2007 Part 6: Reference threshold of hearing for test signals of short duration
- ISO 389-7:2019 Part 7: Reference threshold of hearing under free-field and diffuse-field listening conditions
- ISO 389-8:2004 Part 8: Reference equivalent threshold sound pressure levels for pure tones and circumaural earphones
- ISO 389-9:2009 Part 9: Preferred test conditions for the determination of reference hearing threshold levels
- ISO 390:1993 Products in fibre-reinforced cement — Sampling and inspection
- ISO 404:2013 Steel and steel products — General technical delivery requirements
- ISO 407:2004 Small medical gas cylinders — Pin-index yoke-type valve connections
- ISO 413:1974 Aircraft — Heads of lubricating nipples
- ISO 418:2001 Photography — Processing chemicals — Specifications for anhydrous sodium sulfite
- ISO 420:1994 Photography — Processing chemicals — Specifications for potassium bromide
- ISO 422:1994 Photography — Processing chemicals — Specifications for p-methylaminophenol sulfate
- ISO 423:1994 Photography — Processing chemicals — Specifications for hydroquinone
- ISO 424:1994 Photography — Processing chemicals — Specifications for anhydrous sodium carbonate and sodium carbonate monohydrate
- ISO 428:1983 Wrought copper-aluminium alloys — Chemical composition and forms of wrought products [Withdrawn without replacement]
- ISO 433:2017 Conveyor belts — Marking
- ISO 439:2020 Steel and cast iron — Determination of silicon content — Gravimetric method
- ISO 441:1997 Textile machinery and accessories — Drop wires for warp stop motions for weaving machines without automatic drawing-in
- ISO 445:2013 Pallets for materials handling — Vocabulary
- ISO 446:2004 Micrographics — ISO character and ISO test chart No. 1 — Description and use
- ISO 447:1984 Machine tools — Direction of operation of controls
- ISO 451:1976 Aircraft — Pressure re-oiling connection
- ISO 456:1973 Surface active agents — Analysis of soaps — Determination of free caustic alkali
- ISO 457:1983 Soaps — Determination of chloride content — Titrimetric method
- ISO 458 Plastics — Determination of stiffness in torsion of flexible materials
- ISO 458-1:1985 Part 1: General method
- ISO 458-2:1985 Part 2: Application to plasticized compounds of homopolymers and copolymers of vinyl chloride
- ISO 461 Aircraft — Connectors for ground electrical supplies
- ISO 461-1:2003 Part 1: Design, performance and test requirements
- ISO 461-2:1985 Part 2: Dimensions
- ISO 463:2006 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges
- ISO 464:2015 Rolling bearings — Radial bearings with locating snap ring — Dimensions, geometrical product specifications (GPS) and tolerance values
- ISO 466:1976 Cinematography — Image produced by 16 mm motion-picture camera aperture — Position and dimensions
- ISO 472:2013 Plastics — Vocabulary
- ISO 476:1982 Textile machinery and accessories — Pirn winding machines — Vocabulary
- ISO 477:1982 Textile machinery and accessories — Cone and cheese winding machines — Vocabulary
- ISO 482:1977 Aircraft — Propulsion units and components — Methods of numbering and describing direction of rotation
- ISO 483:2005 Plastics — Small enclosures for conditioning and testing using aqueous solutions to maintain the humidity at a constant value
- ISO 484
- ISO 484-1:2015 Part 1: Propellers of diameter greater than 2,50 m
- ISO 484-2:2015 Part 2: Propellers of diameter between 0,80 and 2,50 m inclusive
- ISO 485:1973 Aircraft water-methanol pressure connections
- ISO 486:1988 Cinematography — 16 mm motion-picture film perforated 8 mm Type R — Cutting and perforating dimensions
- ISO 487:1998 Steel roller chains, types S and C, attachments and sprockets
- ISO 488:2008 Milk — Determination of fat content — Gerber butyrometers
- ISO 489:1999 Plastics — Determination of refractive index
- ISO 490:1993 Cinematography — Magnetic stripes and magnetic recording head gaps for sound record on 16 mm motion-picture film perforated along one edge (Type 1) — Positions and width dimensions
- ISO 491:2002 Cinematography — 35 mm motion-picture film and magnetic film — Cutting and perforating dimensions
- ISO 492:2014 Rolling bearings — Radial bearings — Geometrical product specifications (GPS) and tolerance values
- ISO 493:1975 Aircraft — Dimensions for single-hole mounting (Class 1 and Class 2) lever-operated manual switches
- ISO 494:2017 Cylindrical shank twist drills — Long series
- ISO 496:1973 Driving and driven machines — Shaft heights
- ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
- ISO 498:1992 Natural rubber latex concentrate — Preparation of dry films
- ISO 500 Agricultural tractors — Rear-mounted power take-off types 1, 2, 3 and 4[Note 3]
- ISO 501:2012 Hard coal — Determination of the crucible swelling number
- ISO 502:2015 Coal — Determination of caking power — Gray-King coke test
- ISO 504:1975 Turning tools with carbide tips — Designation and marking
- ISO 505:2017 Conveyor belts — Method for the determination of the tear propagation resistance of textile conveyor belts
- ISO 506:2020 Rubber latex, natural, concentrate — Determination of volatile fatty acid number
- ISO 510:1977 Red lead for paints
- ISO 513:2012 Classification and application of hard cutting materials for metal removal with defined cutting edges — Designation of the main groups and groups of application
- ISO 514:2014 Turning tools with carbide tips — Internal tools
- ISO 516:2019 Camera shutters — Timing — General definition and mechanical shutter measurements
- ISO 517:2008 Photography — Apertures and related properties pertaining to photographic lenses — Designations and measurements
- ISO 518:2006 Photography — Camera accessory shoes, with and without electrical contacts, for photoflash lamps and electronic photoflash units — Specification
- ISO 519:1992 Photography — Hand-held cameras — Flash-connector dimensions
- ISO 520:2010 Cereals and pulses — Determination of the mass of 1 000 grains
- ISO 521:2011 Machine chucking reamers with cylindrical shanks and Morse taper shanks
- ISO 522:1975 Special tolerances for reamers
- ISO 525:2020 Bonded abrasive products — Shape types, designation and marking
- ISO 527 Plastics — Determination of tensile properties
- ISO 527-1:2019 Part 1: General principles
- ISO 527-2:2012 Part 2: Test conditions for moulding and extrusion plastics
- ISO 527-3:2018 Part 3: Test conditions for films and sheets
- ISO 527-4:1997 Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
- ISO 527-5:2009 Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
- ISO 528:1983 Refractory products — Determination of pyrometric cone equivalent (refractoriness)
- ISO 529:2017 Short machine taps and hand taps
- ISO 530:1975 Aircraft — General purpose push-pull single-pole circuit-breakers — Dimensions
- ISO 532 Acoustics — Methods for calculating loudness
- ISO 532-1:2017 Part 1: Zwicker method
- ISO 532-2:2017 Part 2: Moore-Glasberg method
- ISO 534:2011 Paper and board — Determination of thickness, density and specific volume
- ISO 535:2014 Paper and board — Determination of water absorptiveness — Cobb method
- ISO 536:2019 Paper and board — Determination of grammage
- ISO 540:2008 Hard coal and coke — Determination of ash fusibility
- ISO 542:1990 Oilseeds — Sampling
- ISO 544:2017 Welding consumables — Technical delivery conditions for filler materials and fluxes — Type of product, dimensions, tolerances and markings
- ISO 548:1981 Manganese ores — Determination of barium oxide content — Barium sulphate gravimetric method
- ISO 549:1981 Manganese ores — Determination of combined water content — Gravimetric method
- ISO 554:1976 Standard atmospheres for conditioning and/or testing — Specifications
- ISO 556:2020 Coke (greater than 20 mm in size) — Determination of mechanical strength
- ISO 558:1980 Conditioning and testing — Standard atmospheres — Definitions
- ISO 561:1989 Coal preparation plant — Graphical symbols
- ISO 562:2010 Hard coal and coke — Determination of volatile matter
- ISO 565:1990 Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings
- ISO 567:1995 Coke — Determination of bulk density in a small container
- ISO 570:1982 Textile machinery and accessories — Heald carrying rods for healds with closed "O"-shaped end loops
- ISO 579:2013 Coke — Determination of total moisture
- ISO 580:2005 Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating
- ISO/TR 581:2005 Weldability — Metallic materials — General principles
- ISO 582:1995 Rolling bearings — Chamfer dimensions — Maximum values
- ISO 583:2007 Conveyor belts with a textile carcass — Total belt thickness and thickness of constitutive elements — Test methods
- ISO 584:1982 Plastics — Unsaturated polyester resins — Determination of reactivity at 80 degrees C (conventional method)
- ISO 585:1990 Plastics — Unplasticized cellulose acetate — Determination of moisture content
- ISO 587:2020 Coal and coke — Determination of chlorine using Eschka mixture
- ISO 589:2008 Hard coal — Determination of total moisture
- ISO 591 Titanium dioxide pigments for paints
- ISO 591-1:2000 Part 1: Specifications and methods of test
- ISO 592:1998 Essential oils — Determination of optical rotation
- ISO 602:2015 Coal — Determination of mineral matter
- ISO 603 Bonded abrasive products — Dimensions
- ISO 603-1:1999 Part 1: Grinding wheels for external cylindrical grinding between centres
- ISO 603-2:1999 Part 2: Grinding wheels for centreless external cylindrical grinding
- ISO 603-3:1999 Part 3: Grinding wheels for internal cylindrical grinding
- ISO 603-4:1999 Part 4: Grinding wheels for surface grinding/peripheral grinding
- ISO 603-5:1999 Part 5: Grinding wheels for surface grinding/face grinding
- ISO 603-6:1999 Part 6: Grinding wheels for tool and tool room grinding
- ISO 603-7:1999 Part 7: Grinding wheels for manually guided grinding
- ISO 603-8:1999 Part 8: Grinding wheels for deburring and fettling/snagging
- ISO 603-9:1999 Part 9: Grinding wheels for high-pressure grinding
- ISO 603-10:1999 Part 10: Stones for honing and superfinishings
- ISO 603-11:1999 Part 11: Hand finishing sticks
- ISO 603-12:1999 Part 12: Grinding wheels for deburring and fettling on a straight grinder
- ISO 603-13:1999 Part 13: Grinding wheels for deburring and fettling on a vertical grinder
- ISO 603-14:1999 Part 14: Grinding wheels for deburring and fettling/snagging on an angle grinder
- ISO 603-15:1999 Part 15: Grinding wheels for cutting-off on stationary or mobile cutting-off machines
- ISO 603-16:1999 Part 16: Grinding wheels for cutting-off on hand held power tools
- ISO 603-17:2014 Part 17: Spindle mounted wheels (ISO type 52)
- ISO 603-18:2013 Part 18: Grinding wheels for flat glass edge grinding machines
- ISO 604:2002 Plastics — Determination of compressive properties
- ISO 605:1991 Pulses — Determination of impurities, size, foreign odours, insects, and species and variety — Test methods
- ISO 606:2015 Short-pitch transmission precision roller and bush chains, attachments and associated chain sprockets
- ISO 607:1980 Surface active agents and detergents — Methods of sample division
- ISO 609:1996 Solid mineral fuels — Determination of carbon and hydrogen — High temperature combustion method
- ISO 610:1990 High-tensile steel chains (round link) for chain conveyors and coal ploughs
- ISO 611:2003 Road vehicles — Braking of automotive vehicles and their trailers — Vocabulary
- ISO 612:1978 Road vehicles — Dimensions of motor vehicles and towed vehicles — Terms and definitions
- ISO 614:2012 Ships and marine technology — Toughened safety glass panes for rectangular windows and side scuttles — Punch method of non-destructive strength testing
- ISO 616:1995 Coke — Determination of shatter indices
- ISO 619:1981 Manganese ores — Determination of chromium content — Diphenylcarbazide photometric method and silver persulphate titrimetric method
- ISO 622:2016 Solid mineral fuels — Determination of phosphorus content — Reduced molybdophosphate photometric method
- ISO 625:1996 Solid mineral fuels — Determination of carbon and hydrogen — Liebig method
- ISO 629:1982 Steel and cast iron — Determination of manganese content — Spectrophotometric method
- ISO 630 Structural steels
- ISO 630-1:2011 Part 1: General technical delivery conditions for hot-rolled products
- ISO 630-2:2011 Part 2: Technical delivery conditions for structural steels for general purposes
- ISO 630-3:2012 Part 3: Technical delivery conditions for fine-grain structural steels
- ISO 630-4:2012 Part 4: Technical delivery conditions for high-yield-strength quenched and tempered structural steel plates
- ISO 630-5:2014 Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
- ISO 630-6:2014 Part 6: Technical delivery conditions for seismic-improved structural steels for building
- ISO 631:1975 Mosaic parquet panels — General characteristics
- ISO 633:2019 Cork — Vocabulary
- ISO 636:2017 Welding consumables — Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels — Classification
- ISO 638:2008 Paper, board and pulps — Determination of dry matter content — Oven-drying method
- ISO 639 Codes for the representation of names of languages
- ISO 639-1:2002 Part 1: Alpha-2 code
- ISO 639-2:1998 Part 2: Alpha-3 code
- ISO 639-3:2007 Part 3: Alpha-3 code for comprehensive coverage of languages
- ISO 639-4:2010 Part 4: General principles of coding of the representation of names of languages and related entities, and application guidelines
- ISO 639-5:2008 Part 5: Alpha-3 code for language families and groups
- ISO 639-6:2009 Part 6: Alpha-4 code for comprehensive coverage of language variants [Withdrawn, no replacement]
- ISO 641:1975 Laboratory glassware — Interchangeable spherical ground joints
- ISO 642:1999 Steel — Hardenability test by end quenching (Jominy test)
- ISO 643:2019 Steels — Micrographic determination of the apparent grain size
- ISO/IEC 646:1991 Information technology — ISO 7-bit coded character set for information interchange
- ISO 647:2017 Brown coals and lignites — Determination of the yields of tar, water, gas and coke residue by low temperature distillation
- ISO 648:2008 Laboratory glassware — Single-volume pipettes
- ISO 649 Laboratory glassware — Density hydrometers for general purposes
- ISO 649-1:1981 Part 1: Specification
- ISO 649-2:1981 Part 2: Test methods and use
- ISO 650:1977 Relative density 60/60 degrees F hydrometers for general purposes
- ISO 651:1975 Solid-stem calorimeter thermometers
- ISO 652:1975 Enclosed-scale calorimeter thermometers
- ISO 653:1980 Long solid-stem thermometers for precision use
- ISO 654:1980 Short solid-stem thermometers for precision use
- ISO 655:1980 Long enclosed-scale thermometers for precision use
- ISO 656:1980 Short enclosed-scale thermometers for precision use
- ISO 657 Hot-rolled steel sections
- ISO 658:2002 Oilseeds — Determination of content of impurities
- ISO 659:2009 Oilseeds — Determination of oil content (Reference method)
- ISO 660:2020 Animal and vegetable fats and oils — Determination of acid value and acidity
- ISO 661:2003 Animal and vegetable fats and oils — Preparation of test sample
- ISO 662:2016 Animal and vegetable fats and oils — Determination of moisture and volatile matter content
- ISO 663:2017 Animal and vegetable fats and oils — Determination of insoluble impurities content
- ISO 664:2008 Oilseeds — Reduction of laboratory sample to test sample
- ISO 665:2020 Oilseeds — Determination of moisture and volatile matter content
- ISO 666:2012 Machine tools — Mounting of grinding wheels by means of hub flanges
- ISO 668:2020 Series 1 freight containers — Classification, dimensions and ratings
- ISO 669:2016 Resistance welding — Resistance welding equipment — Mechanical and electrical requirements
- ISO 671:1982 Steel and cast iron — Determination of sulphur content — Combustion titrimetric method
- ISO 672:1978 Soaps — Determination of moisture and volatile matter content — Oven method
- ISO 673:1981 Soaps — Determination of content of ethanol-insoluble matter
- ISO 675:2014 Textiles — Woven fabrics — Determination of dimensional change on commercial laundering near the boiling point
- ISO 676:1995 Spices and condiments — Botanical nomenclature
- ISO 677:1976 Straight bevel gears for general engineering and heavy engineering — Basic rack
- ISO 678:1976 Straight bevel gears for general engineering and heavy engineering — Modules and diametral pitches
- ISO 679:2009 Cement — Test methods — Determination of strength
- ISO 683 Heat-treatable steels, alloy steels and free-cutting steels
- ISO 683-1:2016 Part 1: Non-alloy steels for quenching and tempering
- ISO 683-2:2016 Part 2: Alloy steels for quenching and tempering
- ISO 683-3:2019 Part 3: Case-hardening steels
- ISO 683-4:2016 Part 4: Free-cutting steels
- ISO 683-5:2017 Part 5: Nitriding steels
- ISO 683-14:2004 Part 14: Hot-rolled steels for quenched and tempered springs
- ISO 683-15:1992 Part 15: Valve steels for internal combustion engines
- ISO 683-17:2014 Part 17: Ball and roller bearing steels
- ISO 683-18:2014 Part 18: Bright steel products
- ISO 684:1974 Analysis of soaps — Determination of total free alkali
- ISO 685:2020 Analysis of soaps — Determination of total alkali content and total fatty matter content
- ISO 687:2010 Solid mineral fuels — Coke — Determination of moisture in the general analysis test sample
- ISO 690:2010 Information and documentation — Guidelines for bibliographic references and citations to information resources
- ISO 691:2005 Assembly tools for screws and nuts — Wrench and socket openings — Tolerances for general use
- ISO 692:1982 Pulps — Determination of alkali solubility
- ISO 693:1982 Dimensions of seam welding wheel blanks
- ISO 695:1991 Glass — Resistance to attack by a boiling aqueous solution of mixed alkali — Method of test and classification
- ISO 696:1975 Surface active agents — Measurement of foaming power — Modified Ross-Miles method
- ISO 697:1981 Surface active agents — Washing powders — Determination of apparent density — Method by measuring the mass of a given volume
- ISO 699:2015 Pulps — Determination of alkali resistance
- ISO 701:1998 International gear notation — Symbols for geometrical data
- ISO 702 Machine tools — Connecting dimensions of spindle noses and work holding chucks
- ISO 702-1:2009 Part 1: Conical connection
- ISO 702-2:2007 Part 2: Camlock type
- ISO 702-3:2007 Part 3: Bayonet type
- ISO 702-4:2004 Part 4: Cylindrical connection
- ISO 703:2017 Conveyor belts — Transverse flexibility (troughability) — Test method
- ISO 704:2009 Terminology work — Principles and methods
- ISO 705:2015 Rubber latex — Determination of density between 5 degrees C and 40 degrees C
- ISO 706:2004 Rubber latex — Determination of coagulum content (sieve residue)
- ISO 707:2008 Milk and milk products — Guidance on sampling
- ISO 709:2001 Essential oils — Determination of ester value
- ISO 710 Graphical symbols for use on detailed maps, plans and geological cross-sections
- ISO 710-1:1974 Part 1: General rules of representation
- ISO 710-2:1974 Part 2: Representation of sedimentary rocks
- ISO 710-3:1974 Part 3: Representation of magmatic rocks
- ISO 710-4:1982 Part 4: Representation of metamorphic rocks
- ISO 710-5:1989 Part 5: Representation of minerals
- ISO 710-6:1984 Part 6: Representation of contact rocks and rocks which have undergone metasomatic, pneumatolytic or hydrothermal transformation or transformation by weathering
- ISO 710-7:1984 Part 7: Tectonic symbols
- ISO 712:2009 Cereals and cereal products — Determination of moisture content — Reference method
- ISO 714:1975 Zinc — Determination of iron content — Photometric method
- ISO 717 Acoustics — Rating of sound insulation in buildings and of building elements
- ISO 717-1:2020 Part 1: Airborne sound insulation
- ISO 717-2:2020 Part 2: Impact sound insulation
- ISO 718:1990 Laboratory glassware — Thermal shock and thermal shock endurance — Test methods
- ISO 719:2020 Glass — Hydrolytic resistance of glass grains at 98 °C — Method of test and classification
- ISO 720:2020 Glass — Hydrolytic resistance of glass grains at 121 °C — Method of test and classification
- ISO 721:1991 Rock drilling equipment — Integral stems
- ISO 722:1991 Rock drilling equipment — Hollow drill steels in bar form, hexagonal and round
- ISO 723:1991 Rock drilling equipment — Forged collared shanks and corresponding chuck bushings for hollow hexagonal drill steels
- ISO 724:1993 ISO general-purpose metric screw threads — Basic dimensions
- ISO 725:2009 ISO inch screw threads — Basic dimensions
- ISO 727 Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure
- ISO 727-1:2002 Part 1: Metric series
- ISO 727-2:2005 Part 2: Inch-based series
- ISO 728:1995 Coke (nominal top size greater than 20&nsbp;mm) — Size analysis by sieving
- ISO 729:1988 Oilseeds — Determination of acidity of oils
- ISO 730:2009 Agricultural wheeled tractors — Rear-mounted three-point linkage — Categories 1N, 1, 2N, 2, 3N, 3, 4N and 4
- ISO 732:2000 Photography — 120-size and 220-size films — Dimensions
- ISO 734:2015 Oilseed meals — Determination of oil content — Extraction method with hexane (or light petroleum)
- ISO 735:1977 Oilseed residues — Determination of ash insoluble in hydrochloric acid
- ISO 737:1975 Coniferous sawn timber — Sizes — Methods of measurement
- ISO 738:2015 Coniferous sawn timber — Sizes — Permissible deviations and shrinkage
- ISO 739:1976 Sodium carbonate for industrial use — Preparation and storage of test samples
- ISO 740:1976 Sodium carbonate for industrial use — Determination of total soluble alkalinity — Titrimetric method
- ISO 746:1976 Sodium carbonate for industrial use — Determination of matter insoluble in water at 50 degrees C
- ISO 748:2007 Hydrometry — Measurement of liquid flow in open channels using current-meters or floats
- ISO 749:1977 Oilseed residues — Determination of total ash
- ISO 750:1998 Fruit and vegetable products — Determination of titratable acidity
- ISO 751:1998 Fruit and vegetable products — Determination of water-insoluble solids
- ISO 752:2004 Zinc ingots
- ISO 756 Propan-2-ol for industrial use — Methods of test
- ISO 756-1:1981 Part 1: General
- ISO 758:1976 Liquid chemical products for industrial use — Determination of density at 20 degrees C
- ISO 759:1981 Volatile organic liquids for industrial use — Determination of dry residue after evaporation on water bath — General method
- ISO 760:1978 Determination of water — Karl Fischer method (General method)
- ISO 762:2003 Fruit and vegetable products — Determination of mineral impurities content
- ISO 763:2003 Fruit and vegetable products — Determination of ash insoluble in hydrochloric acid
- ISO 764:2020 Horology — Magnetic resistant watches
- ISO 765:2016 Pesticides considered not to require common names
- ISO 770:2002 Crude or rectified oils of Eucalyptus globulus (Eucalyptus globulus Labill.)
- ISO 771:1977 Oilseed residues — Determination of moisture and volatile matter content
- ISO 772:2011 Hydrometry — Vocabulary and symbols
- ISO 776:2011 Pulps — Determination of acid-insoluble ash
- ISO 780:2015 Packaging - Distribution packaging — Graphical symbols for handling and storage of packages
- ISO 787 General methods of test for pigments and extenders
- ISO 787-1:1982 Part 1: Comparison of colour of pigments
- ISO 787-2:1981 Part 2: Determination of matter volatile at 105 degrees C
- ISO 787-3:2000 Part 3: Determination of matter soluble in water — Hot extraction method
- ISO 787-4:1981 Part 4: Determination of acidity or alkalinity of the aqueous extract
- ISO 787-5:1980 Part 5: Determination of oil absorption value
- ISO 787-7:2009 Part 7: Determination of residue on sieve — Water method — Manual procedure
- ISO 787-8:2000 Part 8: Determination of matter soluble in water — Cold extraction method
- ISO 787-9:2019 Part 9: Determination of pH value of an aqueous suspension
- ISO 787-10:1993 Part 10: Determination of density — Pyknometer method
- ISO 787-11:1981 Part 11: Determination of tamped volume and apparent density after tamping
- ISO 787-13:2019 Part 13: Determination of water-soluble sulphates, chlorides and nitrates
- ISO 787-14:2019 Part 14: Determination of resistivity of aqueous extract
- ISO 787-15:2019 Part 15: Comparison of resistance to light of coloured pigments of similar types
- ISO 787-16:1986 Part 16: Determination of relative tinting strength (or equivalent colouring value) and colour on reduction of coloured pigments — Visual comparison method
- ISO 787-17:2019 Part 17: Comparison of lightening power of white pigments
- ISO 787-18:1983 Part 18: Determination of residue on sieve — Mechanical flushing procedure
- ISO 787-19:2020 Part 19: Determination of water-soluble nitrates (Salicylic acid method)
- ISO 787-21:1979 Part 21: Comparison of heat stability of pigments using a stoving medium
- ISO 787-22:1980 Part 22: Comparison of resistance to bleeding of pigments
- ISO 787-23:1979 Part 23: Determination of density (using a centrifuge to remove entrained air)
- ISO 787-24:1985 Part 24: Determination of relative tinting strength of coloured pigments and relative scattering power of white pigments — Photometric methods
- ISO 787-25:2019 Part 25: Comparison of the colour, in full-shade systems, of white, black and coloured pigments — Colorimetric method
- ISO 787-28:2019 Part 28: Determination of total content of polychlorinated biphenyls (PCB) by dissolution, cleanup and GC-MS
- ISO 788:1974 Ultramarine pigments for paints
- ISO 789 Agricultural tractors — Test procedures
- ISO 789-1:2018 Part 1: Power tests for power take-off
- ISO 789-2:2018 Part 2: Rear three-point linkage lifting capacity
- ISO 789-3:2015 Part 3: Turning and clearance diameters
- ISO 789-4:1986 Part 4: Measurement of exhaust smoke
- ISO 789-5:1983 Part 5: Partial power PTO — Non-mechanically transmitted power
- ISO 789-6:2019 Part 6: Centre of gravity
- ISO 789-7:1991 Part 7: Axle power determination
- ISO 789-8:1991 Part 8: Engine air cleaner
- ISO 789-9:2018 Part 9: Power tests for drawbar
- ISO/OECD 789-10:2006 Part 10: Hydraulic power at tractor/implement interface
- ISO 789-11:1996 Part 11: Steering capability of wheeled tractors
- ISO 789-12:2000 Part 12: Low temperature starting
- ISO 789-13:2018 Part 13: Vocabulary and specimen test report
- ISO 791:1973 Magnesium alloys — Determination of aluminium — 8-hydroxyquinoline gravimetric method
- ISO 792:1973 Magnesium and magnesium alloys — Determination of iron — Orthophenanthroline photometric method
- ISO 793:1973 Aluminium and aluminium alloys — Determination of iron — Orthophenanthroline photometric method
- ISO 794:1976 Magnesium and magnesium alloys — Determination of copper content — Oxalyldihydrazide photometric method
- ISO 795:1976 Aluminium and aluminium alloys — Determination of copper content — Oxalyldihydrazide photometric method
- ISO 796:1973 Aluminium alloys — Determination of copper — Electrolytic method
- ISO 797:1973 Aluminium and aluminium alloys — Determination of silicon — Gravimetric method
- ISO 799 Ships and marine technology — Pilot ladders
- ISO 799-1:2019 Part 1: Design and specification
- ISO 801 Pulps — Determination of saleable mass in lots
- ISO 801-1:1994 Part 1: Pulp baled in sheet form
- ISO 801-2:1994 Part 2: Pulps (such as flash-dried pulps) baled in slabs
- ISO 801-3:1994 Part 3: Unitized bales
- ISO 806:2004 Aluminium oxide primarily used for the production of aluminium — Determination of loss of mass at 300 degrees C and 1 000 degrees C
- ISO 808:1973 Aluminium and aluminium alloys — Determination of silicon — Spectrophotometric method with the reduced silicomolybdic complex
- ISO 809:1973 Magnesium and magnesium alloys — Determination of manganese — Periodate photometric method (Manganese content between 0,01 and 0,8 %)
ISO 810:1973 Magnesium and magnesium alloys — Determination of manganese — Periodate photometric method (Manganese content less than 0,01 %)
- ISO 811:2018 Textiles — Determination of resistance to water penetration — Hydrostatic pressure test
- ISO 812:2017 Rubber, vulcanized or thermoplastic — Determination of low-temperature brittleness
- ISO 813:2019 Rubber, vulcanized or thermoplastic — Determination of adhesion to a rigid substrate — 90 degree peel method
- ISO 814:2017 Rubber, vulcanized or thermoplastic — Determination of adhesion to metal — Two-plate method
- ISO 815 Rubber, vulcanized or thermoplastic — Determination of compression set
- ISO 815-1:2019 Part 1: At ambient or elevated temperatures
- ISO 815-2:2019 Part 2: At low temperatures
- ISO 817:2014 Refrigerants — Designation and safety classification
- ISO 830:1999 Freight containers — Vocabulary
- ISO 832:1994 Information and documentation — Bibliographic description and references — Rules for the abbreviation of bibliographic terms
- ISO 834 Fire-resistance tests — Elements of building construction
- ISO 834-1:1999 Part 1: General requirements
- ISO 834-2:2019 Part 2: Requirements and recommendations for measuring furnace exposure on test samples
- ISO/TR 834-3:2012 Part 3: Commentary on test method and guide to the application of the outputs from the fire-resistance test
- ISO 834-4:2000 Part 4: Specific requirements for loadbearing vertical separating elements
- ISO 834-5:2000 Part 5: Specific requirements for loadbearing horizontal separating elements
- ISO 834-6:2000 Part 6: Specific requirements for beams
- ISO 834-7:2000 Part 7: Specific requirements for columns
- ISO 834-8:2002 Part 8: Specific requirements for non-loadbearing vertical separating elements
- ISO 834-9:2003 Part 9: Specific requirements for non-loadbearing ceiling elements
- ISO 834-10:2014 Part 10: Specific requirements to determine the contribution of applied fire protection materials to structural steel elements
- ISO 834-11:2014 Part 11: Specific requirements for the assessment of fire protection to structural steel elements
- ISO 834-12:2012 Part 12: Specific requirements for separating elements evaluated on less than full scale furnaces
- ISO 834-13:2019 Part 13: Requirements for the testing and assessment of applied fire protection to steel beams with web openings
- ISO 834-14:2019 Part 14: Requirements for the testing and assessment of applied fire protection to solid steel bar
- ISO 835:2007 Laboratory glassware — Graduated pipettes
- ISO 836:2001 Terminology for refractories
- ISO 838:1974 Paper — Holes for general filing purposes — Specifications
- ISO 839 Milling machine arbors with 7/24 tapers
- ISO 839-1:2006 Part 1: Dimensions and designation
- ISO 839-2:1977 Part 2: Accessories
- ISO 841:2001 Industrial automation systems and integration — Numerical control of machines — Coordinate system and motion nomenclature
- ISO 843:1997 Information and documentation — Conversion of Greek characters into Latin characters
- ISO 844:2014 Rigid cellular plastics — Determination of compression properties
- ISO 845:2006 Cellular plastics and rubbers — Determination of apparent density
- ISO 846:2019 Plastics — Evaluation of the action of microorganisms
- ISO 855:2003 Oil of lemon [Citrus limon (L.) Burm. f.], obtained by expression
- ISO 856:2006 Oil of peppermint (Mentha x piperita L.)
- ISO 857 Welding and allied processes — Vocabulary
- ISO 857-2:2005 Part 2: Soldering and brazing processes and related terms
- ISO 858:1973 Fishing nets — Designation of netting yarns in the Tex System
- ISO 860:2007 Terminology work — Harmonization of concepts and terms
- ISO 862:1984 Surface active agents — Vocabulary
- ISO 863:2008 Cement — Test methods — Pozzolanicity test for pozzolanic cements
- ISO 865:1981 Slots in platens for projection welding machines
- ISO 866:2016 Centre drills for centre holes without protecting chamfers — Type A
- ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
- ISO 871:2006 Plastics — Determination of ignition temperature using a hot-air furnace
- ISO 873:1980 Peaches — Guide to cold storage
- ISO 874:1980 Fresh fruits and vegetables — Sampling
- ISO 875:1999 Essential oils — Evaluation of miscibility in ethanol
- ISO 877 Plastics — Methods of exposure to solar radiation
- ISO 877-1:2009 Part 1: General guidance
- ISO 877-2:2009 Part 2: Direct weathering and exposure behind window glass
- ISO 877-3:2018 Part 3: Intensified weathering using concentrated solar radiation
- ISO 882 Cardamom (Elettaria cardamomum (Linnaeus) Maton var. minuscula Burkill) — Specification
- ISO 882-1:1993 Part 1: Whole capsules
- ISO 882-2:1993 Part 2: Seeds
- ISO 883:2013 Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole — Dimensions
- ISO 885:2000 General purpose bolts and screws — Metric series — Radii under the head
- ISO 886:1973 Aluminium and aluminium alloys — Determination of manganese — Photometric method (Manganese content between 0,005 and 1,5 %)
- ISO 887:2000 Plain washers for metric bolts, screws and nuts for general purposes — General plan
- ISO 888:2012 Fasteners — Bolts, screws and studs — Nominal lengths and thread lengths
- ISO 893:1989 Surface active agents — Technical alkane sulfonates — Methods of analysis
- ISO 894:1977 Surface active agents — Technical sodium primary alkylsulphates — Methods of analysis
- ISO 895:1977 Surface active agents — Technical sodium secondary alkylsulphates — Methods of analysis
- ISO 897:2000 Photography — Roll films, 126, 110 and 135-size films — Identification of the image-bearing side
- ISO 898 Mechanical properties of fasteners made of carbon steel and alloy steel[Note 3]
- ISO 899 Plastics — Determination of creep behaviour
- ISO 899-1:2017 Part 1: Tensile creep
- ISO 899-2:2003 Part 2: Flexural creep by three-point loading
- ISO 928 Spices and condiments — Determination of total ash
- ISO 936 Meat and meat products — Determination of total ash
- ISO 962:1974 Information processing — Implementation of the 7- bit coded character set and its 7- bit and 8-bit extensions on 9- track 12,7 mm (0.5 in) magnetic tape
- ISO 965 ISO general purpose metric screw threads — Tolerances
- ISO 999:1996 Information and documentation — Guidelines for the content, organization, and presentation of indexes
ISO 1000 – ISO 4999
- ISO 1000 SI units and recommendations for the use of their multiples and of certain other units [withdrawn 2009-11-17]
- ISO/IEC 1001:2012 Information technology – File structure and labelling of magnetic tapes for information interchange
- ISO 1004 Information processing – Magnetic ink character recognition – Print specifications
- ISO 1007 Photography – 135-size film and magazine – Specifications
- ISO 1031:1974 Coniferous sawn timber – Defects – Terms and definitions
- ISO 1032:1974 Coniferous sawn timber – Sizes – Terms and definitions
- ISO 1034:1973 Aircraft - Ground air-conditioning connections
- ISO 1042:1998 Laboratory glassware – One-mark volumetric flasks
- ISO 1069:1973 Magnetic compasses and binnacles for sea navigation – Vocabulary
- ISO 1070:1992 Liquid flow measurement in open channels – Slope-area method
- ISO 1073 Alphanumeric character sets for optical recognition
- ISO 1073-1:1976 Part 1: Character set OCR-A - Shapes and dimensions of the printed image
- ISO 1073-2:1976 Part 2: Character set OCR-B - Shapes and dimensions of the printed image
- ISO 1081:2013 Belt drives - V-belts and V-ribbed belts, and corresponding grooved pulleys - Vocabulary
- ISO 1086:1991 Information and documentation – Title leaves of books
- ISO 1087:2019 Terminology work and terminology science — Vocabulary
- ISO 1088:2007 Hydrometry – Velocity-area methods using current-meters – Collection and processing of data for determination of uncertainties in flow measurement
- ISO 1101:2017 Geometrical product specifications (GPS) – Geometrical tolerancing – Tolerances of form, orientation, location and run-out
- ISO 1100 Hydrometry – Measurement of liquid flow in open channels
- ISO 1100-2:2010 Part 2: Determination of the stage-discharge relationship
- ISO 1107:2017 Fishing nets – Netting – Basic terms and definitions
- ISO 1112:2009 Horology – Functional and non-functional jewels
- ISO 1113:1979 Information processing - Representation of the 7- bit coded character set on punched tape
- ISO 1119:2011 Geometrical product specifications (GPS) - Series of conical tapers and taper angles
- ISO 1122 Vocabulary of gear terms
- ISO 1122-1:1998 Part 1: Definitions related to geometry
- ISO 1122-2:1999 Part 2: Definitions related to worm gear geometry
- ISO 1132 Rolling bearings - Tolerances
- ISO 1132-1:2000 Part 1: Terms and definitions
- ISO 1135 Transfusion equipment for medical use
- ISO 1135-3:2016 Part 3: Blood-taking sets for single use
- ISO 1135-4:2015 Part 4: Transfusion sets for single use, gravity feed
- ISO 1135-5:2015 Part 5: Transfusion sets for single use with pressure infusion apparatus
- ISO 1146:1988 Pyrometric reference cones for laboratory use – Specification
- ISO 1151 Flight dynamics - Concepts, quantities and symbols
- ISO 1151-1:1988 Part 1: Aircraft motion relative to the air
- ISO 1151-2:1985 Part 2: Motions of the aircraft and the atmosphere relative to the Earth
- ISO 1151-3:1989 Part 3: Derivatives of forces, moments and their coefficients
- ISO 1151-4:1994 Part 4: Concepts and quantities used in the study of aircraft stability and control
- ISO 1151-5:1987 Part 5: Quantities used in measurements
- ISO 1151-6:1982 Part 6: Aircraft geometry
- ISO 1151-7:1985 Part 7: Flight points and flight envelopes
- ISO 1151-8:1992 Part 8: Concepts and quantities used in the study of the dynamic behaviour of the aircraft
- ISO 1151-9:1993 Part 9: Models of atmospheric motions along the trajectory of the aircraft
- ISO 1154:1975 Information processing – Punched paper tape – Dimensions and location of feed holes and code holes
- ISO 1155:1978 Information processing – Use of longitudinal parity to detect errors in information messages
- ISO 1176:1990 Road vehicles – Masses – Vocabulary and codes
- ISO 1177:1985 Information processing – Character structure for start/stop and synchronous character oriented transmission
- ISO 1182 Reaction to fire tests for products—Non-combustibility test
- ISO 1213 Solid mineral fuels – Vocabulary
- ISO 1213-1:1993 Part 1: Terms relating to coal preparation
- ISO 1213-2:2016 Part 2: Terms relating to sampling, testing and analysis
- ISO 1217 Displacement compressors—Acceptance tests
- ISO 1219 Fluid power systems and components - Graphical symbols and circuit diagrams
- ISO 1219-1:2012 Part 1: Graphical symbols for conventional use and data-processing applications
- ISO 1219-2:2012 Part 2: Circuit diagrams
- ISO 1219-3:2016 Part 3: Symbol modules and connected symbols in circuit diagrams
- ISO 1222 Photography – Tripod connections
- ISO 1268 Fibre-reinforced plastics – Methods of producing test plates
- ISO/R 1295:1970 Paper vocabulary — Fifth series of terms [Withdrawn: Replaced with ISO 4046]
- ISO 1302:2002 Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation
- ISO 1382:2012 Rubber – Vocabulary
- ISO 1402 Rubber and plastics hoses and hose assemblies - Hydrostatic testing
- ISO 1413:2016 Horology - Shock-resistant wrist watches
- ISO 1438:2017 Hydrometry – Open channel flow measurement using thin-plate weirs
- ISO 1502:1996 ISO general-purpose metric screw threads – Gauges and gauging
- ISO 1506:1982 Textile machinery – Dyeing, finishing and allied machinery – Classification and nomenclature
- ISO 1531:1973 Fishing nets – Hanging of netting – Basic terms and definitions
- ISO 1538:1984 Programming languages - ALGOL 60
- ISO/IEC 1539 Information technology – Programming languages – Fortran
- ISO/IEC 1539-1:2018 Part 1: Base language
- ISO/IEC 1539-2:2000 Part 2: Varying length character strings
- ISO 1586:1977 Textile machinery and accessories – Shuttles – Terms and designation in relation to the position of the shuttle eye
- ISO 1629:2013 Rubber and latices – Nomenclature
- ISO 1660:2017 Geometrical product specifications (GPS) - Geometrical tolerancing - Profile tolerancing
- ISO 1663 Rigid cellular plastics – Determination of water vapour transmission properties
- ISO 1680:2013 Acoustics – Test code for the measurement of airborne noise emitted by rotating electrical machines
- ISO 1681:1973 Information processing – Unpunched paper cards – Specification
- ISO 1683:2015 Acoustics - Preferred reference values for acoustical and vibratory levels
- ISO 1703:2005 Assembly tools for screws and nuts - Designation and nomenclature
- ISO 1730:1980 Dictation equipment – Basic operating requirements
- ISO 1745:1975 Information processing – Basic mode control procedures for data communication systems
- ISO 1750 Pesticides and other agrochemicals – Common names
- ISO 1768:1975 Glass hydrometers – Conventional value for the thermal cubic expansion coefficient (for use in the preparation of measurement tables for liquids)
- ISO 1769:1975 Laboratory glassware – Pipettes – Colour coding
- ISO 1770:1981 Solid-stem general purpose thermometers
- ISO 1771:1981 Enclosed-scale general purpose thermometers
- ISO 1791:1983 Building construction – Modular co-ordination – Vocabulary
- ISO 1803:1997 Building construction – Tolerances – Expression of dimensional accuracy – Principles and terminology
- ISO 1804:1972 Doors – Terminology
- ISO 1809:1977 Textile machinery and accessories – Types of formers for yarn packages – Nomenclature
- ISO 1828:2012 Health informatics – Categorial structure for terminological systems of surgical procedures
- ISO 1837:2003 Lifting hooks – Nomenclature
- ISO 1858:1977 Information processing – General purpose hubs and reels, with 76 mm (3 in) centrehole, for magnetic tape used in interchange instrumentation applications
- ISO 1859:1973 Information processing – Unrecorded magnetic tapes for interchange instrumentation applications – General dimensional requirements
- ISO 1860:1986 Information processing – Precision reels for magnetic tape used in interchange instrumentation applications
- ISO 1861:1975 Information processing – 7- track, 12,7 mm (0.5 in) wide magnetic tape for information interchange recorded at 8 rpmm (200 rpi)
- ISO 1862:1975 Information processing – 9- track, 12,7 mm (0.5 in) wide magnetic tape for information interchange recorded at 8 rpmm (200 rpi)
- ISO/IEC 1863:1990 Information processing – 9-track, 12,7 mm (0,5 in) wide magnetic tape for information interchange using NRZ1 at 32 ftpmm (800 ftpi) – 32 cpmm (800 cpi)
- ISO/IEC 1864:1992 Information technology – Unrecorded 12,7 mm (0,5 in) wide magnetic tape for information interchange – 32 ftpmm (800 ftpi), NRZ1, 126 ftpmm (3 200 ftpi) phase encoded and 356 ftpmm (9 042 ftpi), NRZ1
- ISO 1891:2009 Fasteners - Terminology
- ISO 1891-2:2014 Part 2: Vocabulary and definitions for coatings
- ISO/R 1912:1971 Paper vocabulary — Sixth series of terms (Definition of optical properties) [Withdrawn: Replaced with ISO 4046]
- ISO 1928 Solid mineral fuels – Determination of gross calorific value by the bomb calorimetric method and calculation of net calorific value
- ISO 1938 Geometrical product specifications (GPS) – Dimensional measuring equipment
- ISO 1938-1:2015 Part 1: Plain limit gauges of linear size
- ISO 1938-2:2017 Part 2: Reference disk gauges
- ISO 1942:2009 Dentistry - Vocabulary
- ISO 1951:2007 Presentation/representation of entries in dictionaries - Requirements, recommendations and information
- ISO 1956 Fruits and vegetables – Morphological and structural terminology
- ISO 1956-1:1982 (No part title)
- ISO 1956-2:1989 (No part title)
- ISO 1964:1987 Shipbuilding - Indication of details on the general arrangement plans of ships
- ISO 1968:2004 Fibre ropes and cordage – Vocabulary
- ISO/IEC 1989:2014 Information technology - Programming languages, their environments and system software interfaces - Programming language COBOL
- ISO 1990 Fruits – Nomenclature
- ISO 1990-1:1982 First list
- ISO 1990-2:1985 Second list
- ISO 1991 Vegetables – Nomenclature
- ISO 1991-1:1982 First list
- ISO 1991-2:1995 Part 2: Second list
- ISO 1996 Acoustics – Description, measurement and assessment of environmental noise
- ISO 1996-1:2016 Part 1: Basic quantities and assessment procedures[3]
- ISO 1996-2:2017 Part 2: Determination of sound pressure levels
- ISO 1998 Petroleum industry – Terminology
- ISO 1998-1:1998 Part 1: Raw materials and products
- ISO 1998-2:1998 Part 2: Properties and tests
- ISO 1998-3:1998 Part 3: Exploration and production
- ISO 1998-4:1998 Part 4: Refining
- ISO 1998-5:1998 Part 5: Transport, storage, distribution
- ISO 1998-6:2000 Part 6: Measurement
- ISO 1998-7:1998 Part 7: Miscellaneous terms
- ISO 1998-99:2000 Part 99: General and index
- ISO 1999:2013 Acoustics - Estimation of noise-induced hearing loss[4]
- ISO 2014:1976 Writing of calendar dates in all-numeric form [Withdrawn: replaced by ISO 8601:1988]
- ISO 2015:1976 Numbering of weeks [Withdrawn: replaced by ISO 8601:1988]
- ISO 2017 Mechanical vibration and shock – Resilient mounting systems
- ISO 2017-1:2005 Part 1: Technical information to be exchanged for the application of isolation systems
- ISO 2017-2:2007 Part 2: Technical information to be exchanged for the application of vibration isolation associated with railway systems
- ISO 2017-3:2015 Part 3: Technical information to be exchanged for application of vibration isolation to new buildings
- ISO/IEC 2022:1994 Information technology – Character code structure and extension techniques
- ISO 2033:1983 Information processing - Coding of machine readable characters (MICR and OCR)
- ISO 2041:2009 Mechanical vibration, shock and condition monitoring - Vocabulary
- ISO 2047:1975 Information processing - Graphical representations for the control characters of the 7- bit coded character set
- ISO 2074:2007 Plywood – Vocabulary
- ISO 2076:2013 Textiles – Man-made fibres – Generic names
- ISO 2080:2008 Metallic and other inorganic coatings - Surface treatment, metallic and other inorganic coatings - Vocabulary
- ISO 2108:2005 Information and documentation – International standard book number (ISBN)
- ISO 2110:1989 Information technology – Data communication – 25-pole DTE/DCE interface connector and contact number assignments
- ISO 2145:1978 Documentation – Numbering of divisions and subdivisions in written documents
- ISO 2146:2010 Information and documentation - Registry services for libraries and related organizations
- ISO 2148:1974 Continuous handling equipment – Nomenclature
- ISO 2151:2004 Acoustics – Noise test code for compressors and vacuum pumps – Engineering method (Grade 2)
- ISO 2162 Technical product documentation – Springs
- ISO 2162-1:1993 Part 1: Simplified representation
- ISO 2162-2:1993 Part 2: Presentation of data for cylindrical helical compression springs
- ISO 2171 Cereals, pulses and by-products – Determination of ash yield by incineration
- ISO 2186:2007 Fluid flow in closed conduits – Connections for pressure signal transmissions between primary and secondary elements
- ISO 2187:1990 Spinning preparatory machinery, spinning and doubling (twisting) machinery – List of equivalent terms
- ISO 2203:1973 Technical drawings – Conventional representation of gears
- ISO 2205:1975 Textile machinery and accessories – Drafting arrangements for spinning machines – Terminology
- ISO 2240:2003 Photography – Colour reversal camera films – Determination of ISO speed
- ISO 2257:1980 Office machines and printing machines used for information processing – Widths of fabric printing ribbons on spools
- ISO 2258:1976 Printing ribbons – Minimum markings to appear on containers
- ISO 2281:1990 Horology - Water-resistant watches [Withdrawn: replaced by ISO 22810:2010]
- ISO 2300:1973 Sawn timber of broadleaved species – Defects – Terms and definitions
- ISO 2331:1974 Fork lift trucks – Hook-on type fork arms – Vocabulary
- ISO/IEC 2375:2003 Information technology - Procedure for registration of escape sequences and coded character sets
- ISO/IEC 2382:2015 Information technology - Vocabulary
- ISO/IEC 2382-36:2013 Part 36: Learning, education and training
- ISO/IEC 2382-37:2017 Part 37: Biometrics
- ISO 2384:1977 Documentation – Presentation of translations
- ISO 2395:1990 Test sieves and test sieving - Vocabulary
- ISO 2425:2010 Hydrometry – Measurement of liquid flow in open channels under tidal conditions
- ISO 2444:1988 Joints in building – Vocabulary
- ISO 2532:1974 Steel wire ropes - Vocabulary
- ISO 2533:1975 Standard Atmosphere
- ISO 2537:2007 Hydrometry – Rotating-element current-meters
- ISO 2538 Geometrical product specifications (GPS) - Wedges
- ISO 2538-1:2014 Part 1: Series of angles and slopes
- ISO 2538-2:2014 Part 2: Dimensioning and tolerancing
- ISO 2553:2013 Welding and allied processes – Symbolic representation on drawings – Welded joints
- ISO 2574:1994 Aircraft – Electrical cables – Identification marking
- ISO 2575:2010 Road vehicles - Symbols for controls, indicators and tell-tales
- ISO/IEC 2593:2000 Information technology – Telecommunications and information exchange between systems – 34-pole DTE/DCE interface connector mateability dimensions and contact number assignments
- ISO 2602:1980 Statistical interpretation of test results - Estimation of the mean - Confidence interval
- ISO 2628:1973 Basic mode control procedures – Complements
- ISO 2629:1973 Basic mode control procedures – Conversational information message transfer
- ISO 2669:1995 Environmental tests for aircraft equipment - Steady-state acceleration
- ISO 2671:1982 Environmental tests for aircraft equipment - Part 3.4 : Acoustic vibration
- ISO 2685:1998 Aircraft - Environmental test procedure for airborne equipment - Resistance to fire in designated fire zones
- ISO 2692:2014 Geometrical product specifications (GPS) – Geometrical tolerancing – Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
- ISO 2709:2008 Information and documentation – Format for information exchange
- ISO 2710 Reciprocating internal combustion engines - Vocabulary
- ISO 2710-1:2000 Part 1: Terms for engine design and operation
- ISO 2710-2:1999 Part 2: Terms for engine maintenance
- ISO 2711:1973 Information processing interchange - Representation of ordinal dates [Withdrawn: replaced by ISO 8601:1988]
- ISO 2768 General tolerances
- ISO 2768-1:1989 Part 1: Tolerances for linear and angular dimensions without individual tolerance indications
- ISO 2768-2:1989 Part 2: Geometrical tolerances for features without individual tolerance indications
- ISO 2775:1977 Office machines and printing machines used for information processing – Widths of one-time paper or plastic printing ribbons and marking to indicate the end of the ribbons
- ISO 2784:1974 Continuous forms used for information processing - Sizes and sprocket feed holes
- ISO 2788:1986 Documentation - Guidelines for the establishment and development of monolingual thesauri [Withdrawn: replaced by ISO 25964-1:2011]
- ISO 2789:2013 Information and documentation - International library statistics
- ISO 2806:1994 Industrial automation systems - Numerical control of machines - Vocabulary
- ISO 2822 Raw cattle hides and calf skins
- ISO 2822-1:1998 Part 1: Descriptions of defects
- ISO 2848:1984 Building construction - Modular coordination - Principles and rules
- ISO 2852 Stainless steel clamp pipe couplings for the food industry
- ISO 2854:1976 Statistical interpretation of data - Techniques of estimation and tests relating to means and variances
- ISO 2859 Sampling procedures for inspection by attributes
- ISO 2859-1:1999 Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
- ISO 2859-2:1985 Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection
- ISO 2859-3:2005 Part 3: Skip-lot sampling procedures
- ISO 2859-4:2002 Part 4: Procedures for assessment of declared quality levels
- ISO 2859-5:2005 Part 5: System of sequential sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection
- ISO 2859-10:2006 Part 10: Introduction to the ISO 2859 series of standards for sampling for inspection by attributes
- ISO 2922:2000 Acoustics – Measurement of airborne sound emitted by vessels on inland waterways and harbours
- ISO 2923:1996 Acoustics - Measurement of noise on board vessels
- ISO 2954:2012 Mechanical vibration of rotating and reciprocating machinery – Requirements for instruments for measuring vibration severity
- ISO 2972:1979 Numerical control of machines - Symbols
- ISO 2975 Measurement of water flow in closed conduits – Tracer methods
- ISO 2975-1:1974 Part 1: General
- ISO 2975-2:1975 Part 2: Constant rate injection method using non-radioactive tracers
- ISO 2975-3:1976 Part 3: Constant rate injection method using radioactive tracers
- ISO 2975-6:1977 Part 6: Transit time method using non-radioactive tracers
- ISO 2975-7:1977 Part 7: Transit time method using radioactive tracers
- ISO 3002 Basic quantities in cutting and grinding
- ISO 3002-1:1982 Part 1: Geometry of the active part of cutting tools – General terms, reference systems, tool and working angles, chip breakers
- ISO 3002-2:1982 Part 2: Geometry of the active part of cutting tools – General conversion formulae to relate tool and working angles
- ISO 3002-3:1984 Part 3: Geometric and kinematic quantities in cutting
- ISO 3002-4:1984 Part 4: Forces, energy, power
- ISO 3002-5:1989 Part 5: Basic terminology for grinding processes using grinding wheels
- ISO 3029:1995 Photography - 126-size cartridges - Dimensions of cartridge, film and backing paper [Withdrawn without replacement]
- ISO 3040:2016 Geometrical product specifications (GPS) – Dimensioning and tolerancing – Cones
- ISO 3046 Reciprocating internal combustion engines – Performance
- ISO 3046-5:2001 Part 5: Torsional vibrations
- ISO 3082 Iron ores – Sampling and sample preparation procedures
- ISO 3095:2013 Acoustics – Railway applications – Measurement of noise emitted by railbound vehicles
- ISO 3098 Technical product documentation – Lettering
- ISO 3098-1:2015 Part 1: General requirements
- ISO 3098-2:2000 Part 2: Latin alphabet, numerals and marks
- ISO 3098-3:2000 Part 3: Greek alphabet
- ISO 3098-4:2000 Part 4: Diacritical and particular marks for the Latin alphabet
- ISO 3098-5:1997 Part 5: CAD lettering of the Latin alphabet, numerals and marks
- ISO 3098-6:2000 Part 6: Cyrillic alphabet
- ISO 3103 Tea – Preparation of liquor for use in sensory tests
- ISO 3105:1994 Glass capillary kinematic viscometers – Specifications and operating instructions
- ISO 3166 Codes for the representation of names of countries and their subdivisions
- ISO 3166-1:2013 Part 1: Country codes
- ISO 3166-2:2013 Part 2: Country subdivision code
- ISO 3166-3:2013 Part 3: Code for formerly used names of countries
- ISO 3252:1999 Powder metallurgy – Vocabulary
- ISO 3272 Microfilming of technical drawings and other drawing office documents
- ISO 3272-1:2003 Part 1: Operating procedures
- ISO 3272-2:1994 Part 2: Quality criteria and control of 35 mm silver gelatin microfilms
- ISO 3272-3:2001 Part 3: Aperture card for 35 mm microfilm
- ISO 3272-4:1994 Part 4: Microfilming of drawings of special and exceptional elongated sizes
- ISO 3272-6:2000 Part 6: Quality criteria and control of systems for enlargements from 35 mm microfilm
- ISO 3274:1996 Geometrical Product Specifications (GPS) – Surface texture: Profile method – Nominal characteristics of contact (stylus) instruments
- ISO 3275:1974 Information processing - Implementation of the 7- bit coded character set and its 7- bit and 8- bit extensions on 3,81 mm magnetic cassette for data interchange
- ISO 3287:1999 Powered industrial trucks - Symbols for operator controls and other displays
- ISO 3297:2007 Information and documentation – International standard serial number (ISSN)
- ISO 3301:1975 Statistical interpretation of data - Comparison of two means in the case of paired observations
- ISO 3307:1975 Information interchange - Representations of time of the day [Withdrawn: replaced by ISO 8601:1988]
- ISO 3354:2008 Measurement of clean water flow in closed conduits – Velocity-area method using current-meters in full conduits and under regular flow conditions
- ISO 3381:2005 Railway applications – Acoustics – Measurement of noise inside railbound vehicles
- ISO 3394:2012 Packaging - Complete, filled transport packages and unit loads - Dimensions of rigid rectangular packages
- ISO 3407:1983 Information processing – Information interchange on 3,81 mm (0.150 in) magnetic tape cassette at 4 cpmm (100 cpi), phase encoded at 63 ftpmm (1 600 ftpi)
- ISO 3408 Ball screws
- ISO 3408-1:2006 Part 1: Vocabulary and designation
- ISO 3454:2008 Hydrometry – Direct depth sounding and suspension equipment
- ISO 3455:2007 Hydrometry – Calibration of current-meters in straight open tanks
- ISO 3493:2014 Vanilla – Vocabulary
- ISO 3494:1976 Statistical interpretation of data - Power of tests relating to means and variances
- ISO 3506 Mechanical properties of corrosion-resistant stainless steel fasteners
- ISO 3507:1999 Laboratory glassware – Pyknometers
- ISO 3509:2005 Coffee and coffee products – Vocabulary
- ISO 3511 Industrial process measurement control functions and instrumentation - Symbolic representation[Note 3]
- ISO 3511-1:1977 Part 1: Basic requirements
- ISO 3511-2:1984 Part 2: Extension of basic requirements
- ISO 3511-3:1984 Part 3: Detailed symbols for instrument interconnection diagrams
- ISO 3511-4:1985 Part 4: Basic symbols for process computer, interface, and shared display/control functions
- ISO 3529 Vacuum technology - Vocabulary
- ISO 3529-1:1981 Part 1: General terms
- ISO 3529-2:1981 Part 2: Vacuum pumps and related terms
- ISO 3529-3:2014 Part 3: Total and partial pressure vacuum gauges
- ISO 3534 Statistics – Vocabulary and symbols
- ISO 3534-1:2006 Part 1: General statistical terms and terms used in probability
- ISO 3534-2:2006 Part 2: Applied statistics
- ISO 3534-3:2013 Part 3: Design of experiments
- ISO 3534-4:2014 Part 4: Survey sampling
- ISO 3535:1977 Forms design sheet and layout chart
- ISO 3536:2016 Road vehicles – Safety glazing materials – Vocabulary
- ISO 3537 Road vehicles – Safety glazing materials – Mechanical tests
- ISO 3538 Road vehicles – Safety glazing materials – Test methods for optical properties
- ISO 3540:1976 Paper or plastic printing ribbons – Characteristics of cores
- ISO 3561:1976 Information processing – Interchangeable magnetic six-disk pack – Track format
- ISO 3562:1976 Information processing – Interchangeable magnetic single-disk cartridge (top loaded) – Physical and magnetic characteristics
- ISO 3563:1976 Information processing – Interchangeable magnetic single-disk cartridge (top loaded) – Track format
- ISO 3564:1976 Information processing – Interchangeable magnetic eleven-disk pack – Physical and magnetic characteristics
- ISO 3572:1976 Textiles – Weaves – Definitions of general terms and basic weaves
- ISO 3591 Sensory analysis – Apparatus – Wine-tasting glass
- ISO 3593 Starch — Determination of ash
- ISO 3601 Fluid power systems – O-rings
- ISO 3601-1 Inside diameters, cross-sections, tolerances and designation codes
- ISO 3601-2 Housing dimensions for general applications
- ISO 3601-3 Quality acceptance criteria
- ISO 3601-4 Anti-extrusion rings (back-up rings)
- ISO 3601-5 Suitability of elastomeric materials for industrial applications
- ISO 3602:1989 Documentation – Romanization of Japanese (kana script)
- ISO 3611:2010 Geometrical product specifications (GPS) – Dimensional measuring equipment: Micrometers for external measurements – Design and metrological characteristics
- ISO 3632 Spices – Saffron (Crocus sativus L.)[Note 3]
- ISO 3635:1981 Size designation of clothes – Definitions and body measurement procedure
- ISO 3650:1998 Geometrical Product Specifications (GPS) – Length standards – Gauge blocks
- ISO 3660:1976 Fishing nets – Mounting and joining of netting – Terms and illustrations
- ISO/TR 3666:1998 Viscosity of water
- ISO 3676:2012 Packaging - Complete, filled transport packages and unit loads - Unit load dimensions
- ISO 3690 Welding and allied processes — Determination of hydrogen content in arc weld metal
- ISO 3692:1976 Information processing – Reels and cores for 25,4 mm (1 in) perforated paper tape for information interchange – Dimensions
- ISO 3713:1987 Ferroalloys - Sampling and preparation of samples - General rules
- ISO 3715 Ships and marine technology – Propulsion plants for ships
- ISO 3715-1:2002 Part 1: Vocabulary for geometry of propellers
- ISO 3715-2:2001 Part 2: Vocabulary for controllable-pitch propeller plants
- ISO/TS 3716:2006 Hydrometry – Functional requirements and characteristics of suspended-sediment samplers
- ISO 3740:2000 Acoustics – Determination of sound power levels of noise sources – Guidelines for the use of basic standards
- ISO 3741:2010 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Precision methods for reverberation test rooms
- ISO 3743 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering methods for small movable sources in reverberant fields[Note 3]
- ISO 3743-1:2010 Part 1: Comparison method for a hard-walled test room
- ISO 3743-2:1994 Part 2: Methods for special reverberation test rooms
- ISO 3744:2010 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering methods for an essentially free field over a reflecting plane
- ISO 3745:2012 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Precision methods for anechoic rooms and hemi-anechoic rooms
- ISO 3746:2010 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Survey method using an enveloping measurement surface over a reflecting plane
- ISO 3747:2010 Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering/survey methods for use in situ in a reverberant environment
- ISO 3766:2003 Construction drawings – Simplified representation of concrete reinforcement
- ISO 3767 Tractors, machinery for agriculture and forestry, powered lawn and garden equipment - Symbols for operator controls and other displays
- ISO 3767-1:2016 Part 1: Common symbols
- ISO 3767-2:2016 Part 2: Symbols for agricultural tractors and machinery
- ISO 3767-3:2016 Part 3: Symbols for powered lawn and garden equipment
- ISO 3767-4:2016 Part 4: Symbols for forestry machinery
- ISO 3767-5:2016 Part 5: Symbols for manual portable forestry machines
- ISO/IEC 3788:1990 Information processing – 9-track, 12,7 mm (0,5 in) wide magnetic tape for information interchange using phase encoding at 126 ftpmm (3 200 ftpi), 63 cpmm (1 600 cpi)
- ISO 3791:1976 Office machines and data processing equipment - Keyboard layouts for numeric applications
- ISO 3792:1976 Adding machines - Layout of function keyboard
- ISO 3802:1976 Information processing – General purpose reels with 8 mm (5/16 in) centre hole for magnetic tape for interchange instrumentation applications
- ISO 3819:2015 Laboratory glassware – Beakers
- ISO 3822 Acoustics – Laboratory tests on noise emission from appliances and equipment used in water supply installations
- ISO 3822-1:1999 Part 1: Method of measurement
- ISO 3822-2:1995 Part 2: Mounting and operating conditions for draw-off taps and mixing valves
- ISO 3822-3:1997 Part 3: Mounting and operating conditions for in-line valves and appliances
- ISO 3822-4:1997 Part 4: Mounting and operating conditions for special appliances
- ISO 3826 Plastics collapsible containers for human blood and blood components
- ISO 3826-1:2013 Part 1: Conventional containers
- ISO 3826-2:2008 Part 2: Graphical symbols for use on labels and instruction leaflets
- ISO 3826-3:2006 Part 3: Blood bag systems with integrated features
- ISO 3826-4:2015 Part 4: Aphaeresis blood bag systems with integrated features
- ISO 3828:2008 Shipbuilding and marine structures – Deck machinery – Vocabulary and symbols
- ISO 3833:1977 Road vehicles – Types – Terms and definitions
- ISO 3835 Equipment for vine cultivation and wine making – Vocabulary
- ISO 3835-1:1976 (No part title)
- ISO 3835-3:1980 (No part title)
- ISO 3835-4:1981 (No part title)
- ISO 3846:2008 Hydrometry – Open channel flow measurement using rectangular broad-crested weirs
- ISO 3847:1977 Liquid flow measurement in open channels by weirs and flumes – End-depth method for estimation of flow in rectangular channels with a free overfall
- ISO 3855:1977 Milling cutters - Nomenclature
- ISO 3857 Compressors, pneumatic tools and machines - Vocabulary
- ISO 3857-1:1977 Part 1: General
- ISO 3857-2:1977 Part 2: Compressors
- ISO 3857-3:1989 Part 3: Pneumatic tools and machines
- ISO 3857-4:2012 Part 4: Air treatment
- ISO 3861:2005 Rubber hoses for sand and grit blasting - Specification
- ISO 3864 Graphical symbols – Safety colours and safety signs
- ISO 3866:1977 Office machines and printing machines used for information processing – Widths of fabric printing ribbons on spools exceeding 19 mm
- ISO 3877 Tyres, valves and tubes – List of equivalent terms
- ISO 3877-1:1997 Part 1: Tyres
- ISO 3877-2:1997 Part 2: Tyre valves
- ISO 3877-3:1978 Part 3: Tubes
- ISO 3877-4:1984 Part 4: Solid tyres
- ISO 3880 Building construction – Stairs – Vocabulary
- ISO 3880-1:1977
- ISO 3883:1977 Office machines – Line and character capacity of address masters
- ISO 3901:2001 Information and documentation – International Standard Recording Code (ISRC)
- ISO 3911:2004 Wheels and rims for pneumatic tyres – Vocabulary, designation and marking
- ISO 3918:2007 Milking machine installations – Vocabulary
- ISO 3950:2016 Dentistry - Designation system for teeth and areas of the oral cavity
- ISO 3951 Sampling procedures for inspection by variables
- ISO 3951-1:2013 Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL
- ISO 3951-2:2013 Part 2: General specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics
- ISO 3951-3:2007 Part 3: Double sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
- ISO 3951-4:2011 Part 4: Procedures for assessment of declared quality levels
- ISO 3951-5:2006 Part 5: Sequential sampling plans indexed by acceptance quality limit (AQL) for inspection by variables (known standard deviation)
- ISO 3952 Kinematic diagrams - Graphical symbols
- ISO 3952-1:1981 (Motion of links of mechanisms; Kinematic pairs; Links and connections of their components; Linkage of bars and their links)
- ISO 3952-2:1981 (Friction and gear mechanisms; Cam mechanisms)
- ISO 3952-3:1979 (Maltese and ratchet mechanisms; Couplings and brakes)
- ISO 3952-4:1984 (Miscellaneous mechanisms and their components)
- ISO 3966:2008 Measurement of fluid flow in closed conduits – Velocity area method using Pitot static tubes
- ISO 3977 Gas turbines – Procurement
- ISO 4006:1991 Measurement of fluid flow in closed conduits - Vocabulary and symbols
- ISO 4007:2012 Personal protective equipment - Eye and face protection - Vocabulary
- ISO 4031:1978 Information interchange - Representation of local time differentials [Withdrawn: replaced by ISO 8601:1988]
- ISO 4037 X and gamma reference radiation for calibrating dosemeters and doserate meters and for determining their response as a function of photon energy
- ISO 4037-1:1996 Part 1: Radiation characteristics and production
- ISO 4037-2:1997 Part 2: Dosimetry for radiation protection over the energy ranges from 8 keV to 1,3 MeV and 4 MeV to 9 MeV
- ISO 4037-3:1999 Part 3: Calibration of area and personal dosemeters and the measurement of their response as a function of energy and angle of incidence
- ISO 4037-4:2004 Part 4: Calibration of area and personal dosemeters in low energy X reference radiation fields
- ISO 4046 Paper, board, pulps and related terms – Vocabulary
- ISO 4046-1:2016 Part 1: Alphabetical index
- ISO 4046-2:2016 Part 2: Pulping terminology
- ISO 4046-3:2016 Part 3: Paper-making terminology
- ISO 4046-4:2016 Part 4: Paper and board grades and converted products
- ISO 4046-5:2016 Part 5: Properties of pulp, paper and board
- ISO 4057:1986 Information processing – Data interchange on 6,30 mm (0.25 in) magnetic tape cartridge, 63 bpmm (1 600 bpi) phase-encoded
- ISO 4063:2009 Welding and allied processes - Nomenclature of processes and reference numbers
- ISO 4074 Natural latex rubber condoms – Requirements and test methods
- ISO 4087:2005 Micrographics - Microfilming of newspapers for archival purposes on 35 mm microfilm
- ISO 4125:1991 Dry fruits and dried fruits – Definitions and nomenclature
- ISO 4129:2012 Road vehicles - Mopeds - Symbols for controls, indicators and tell-tales
- ISO 4130:1978 Road vehicles – Three-dimensional reference system and fiducial marks – Definitions
- ISO 4135:2001 Anaesthetic and respiratory equipment - Vocabulary
- ISO 4139:1979 Ferrosilicon - Determination of aluminium content - Flame atomic absorption spectrometric method
- ISO 4140:1979 Ferrochromium and ferrosilicochromium - Determination of chromium content - Potentiometric method
- ISO 4157 Construction drawings – Designation systems
- ISO 4158:1978 Ferrosilicon, ferrosilicomanganese and ferrosilicochromium - Determination of silicon content - Gravimetric method
- ISO 4159:1978 Ferromanganese and ferrosilicomanganese - Determination of manganese content - Potentiometric method
- ISO 4165 Road vehicles — Electrical connections — Double-pole connection
- ISO 4172:1991 Technical drawings – Construction drawings – Drawings for the assembly of prefabricated structures
- ISO 4173:1980 Ferromolybdenum - Determination of molybdenum content - Gravimetric method
- ISO 4179 Ductile iron pipes and fittings for pressure and non-pressure pipelines – Cement mortar lining
- ISO 4185:1980 Measurement of liquid flow in closed conduits – Weighing method
- ISO 4217:2015 Codes for the representation of currencies
- ISO 4223 Definitions of some terms used in the tyre industry
- ISO 4223-1:2017 Part 1: Pneumatic tyres
- ISO 4223-2:1991 Part 2: Solid tyres
- ISO 4225:1994 Air quality - General aspects - Vocabulary
- ISO 4226:2007 Air quality – General aspects – Units of measurement
- ISO 4232 Office machines – Minimum information to be included in specification sheets
- ISO 4232-3:1984 Part 3: Postal franking machines
- ISO 4246:1994 Cinematography - Vocabulary
- ISO 4248:1978 Jig bushes - Definitions and nomenclature
- ISO 4287:1997 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Terms, definitions and surface texture parameters
- ISO 4288:1996 Geometrical Product Specifications (GPS) - Surface texture: Profile method - Rules and procedures for the assessment of surface texture
- ISO 4291:1985 Methods for the assessment of departure from roundness - Measurement of variations in radius
- ISO 4306 Cranes – Vocabulary
- ISO 4306-1:2007 Part 1: General
- ISO 4306-2:2012 Part 2: Mobile cranes
- ISO 4306-3:2016 Part 3: Tower cranes
- ISO 4306-5:2005 Part 5: Bridge and gantry cranes
- ISO 4314 Surface active agents — Determination of free alkalinity or free acidity — Titrimetric method
- ISO 4337:1977 Information processing – Interchangeable magnetic twelve-disk pack (100 Mbytes)
- ISO 4341:1978 Information processing – Magnetic tape cassette and cartridge labelling and file structure for information interchange
- ISO 4346:1977 Steel wire ropes for general purposes - Lubricants - Basic requirements
- ISO 4359:2013 Flow measurement structures – Rectangular, trapezoidal and U-shaped flumes
- ISO 4360:2008 Hydrometry – Open channel flow measurement using triangular profile weirs
- ISO 4362:1999 Hydrometric determinations – Flow measurement in open channels using structures – Trapezoidal broad-crested weirs
- ISO 4363:2002 Measurement of liquid flow in open channels – Methods for measurement of characteristics of suspended sediment
- ISO 4364:1997 Measurement of liquid flow in open channels – Bed material sampling
- ISO 4365:2005 Liquid flow in open channels – Sediment in streams and canals – Determination of concentration, particle size distribution and relative density
- ISO 4366:2007 Hydrometry – Echo sounders for water depth measurements
- ISO 4369:1979 Measurement of liquid flow in open channels – Moving-boat method
- ISO 4371:1984 Measurement of liquid flow in open channels by weirs and flumes – End depth method for estimation of flow in non-rectangular channels with a free overfall (approximate method)
- ISO 4373:2008 Hydrometry – Water level measuring devices
- ISO 4374:1990 Liquid flow measurement in open channels – Round-nose horizontal broad-crested weirs
- ISO 4375:2014 Hydrometry – Cableway systems for stream gauging
- ISO 4377:2012 Hydrometric determinations – Flow measurement in open channels using structures – Flat-V weirs
- ISO 4378 Plain bearings - Terms, definitions, classification and symbols
- ISO 4378-1:2017 Part 1: Design, bearing materials and their properties
- ISO 4378-2:2017 Part 2: Friction and wear
- ISO 4378-3:2017 Part 3: Lubrication
- ISO 4378-4:2009 Part 4: Basic symbols
- ISO 4378-5:2009 Part 5: Application of symbols
- ISO/TR 4378-6:2012 Part 6: Abbreviated terms
- ISO 4412 Hydraulic fluid power – Test code for determination of airborne noise levels
- ISO 4412-1:1991 Part 1: Pumps
- ISO 4412-2:1991 Part 2: Motors
- ISO 4412-3:1991 Part 3: Pumps – Method using a parallelepiped microphone array
- ISO 4413:2010 Hydraulic fluid power – General rules and safety requirements for systems and their components
- ISO 4481:1977 Cutlery and flatware – Nomenclature
- ISO 4548 Methods of test for full-flow lubricating oil filters for internal combustion engines
- ISO 4548-7:2012 Part 7: Vibration fatigue test
- ISO 4551:1987 Ferroalloys - Sampling and sieve analysis
- ISO 4552 Ferroalloys - Sampling and sample preparation for chemical analysis
- ISO 4552-1:1987 Part 1: Ferrochromium, ferrosilicochromium, ferrosilicon, ferrosilicomanganese, ferromanganese
- ISO 4552-2:1987 Part 2: Ferrotitanium, ferromolybdenum, ferrotungsten, ferroniobium, ferrovanadium
- ISO 4578 Adhesives — Determination of peel resistance of high-strength adhesive bonds — Floating-roller method
- ISO 4582 Plastics — Determination of changes in colour and variations in properties after exposure to daylight under glass, natural weathering or laboratory light sources
- ISO 4587 Adhesives — Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies
- ISO 4618:2014 Paints and varnishes – Terms and definitions
- ISO 4628 Paints and varnishes – Evaluation of degradation of coatings – Designation of quantity and size of defects, and of intensity of uniform changes in appearance
- ISO 4628-1 General introduction and designation system
- ISO 4628-2 Assessment of degree of blistering
- ISO 4628-3 Assessment of degree of rusting
- ISO 4628-4 Assessment of degree of cracking
- ISO 4628-5 Assessment of degree of flaking
- ISO 4628-6 Assessment of degree of chalking by tape method
- ISO 4628-7 Assessment of degree of chalking by velvet method
- ISO 4628-8 Assessment of degree of delamination and corrosion around a scribe
- ISO 4628-10 Assessment of degree of filiform corrosion
- ISO 4683 Raw sheep skins
- ISO 4683-1:1998 Part 1: Descriptions of defects
- ISO 4720:2009 Essential oils – Nomenclature
- ISO 4730:2017 Essential oil of Melaleuca, terpinen-4-ol type (Tea Tree oil)
- ISO 4786:1977 Enclosed-scale adjustable-range thermometers
- ISO 4787:2010 Laboratory glassware – Volumetric instruments – Methods for testing of capacity and for use
- ISO 4788:2005 Laboratory glassware – Graduated measuring cylinders
- ISO 4791 Laboratory apparatus – Vocabulary relating to apparatus made essentially from glass, porcelain or vitreous silica
- ISO 4791-1:1985 Part 1: Names for items of apparatus
- ISO 4795:1996 Glass for thermometer bulbs
- ISO 4801:1979 Glass alcoholometers and alcohol hydrometers not incorporating a thermometer
- ISO 4805:1982 Laboratory glassware – Thermo-alcoholometers and alcohol-thermohydrometers
- ISO 4831:2006 Microbiology of food and animal feeding stuffs – Horizontal method for the detection and enumeration of coliforms – Most probable number technique
- ISO 4832:2006 Microbiology of food and animal feeding stuffs – Horizontal method for the enumeration of coliforms – Colony-count technique
- ISO 4833 Microbiology of the food chain – Horizontal method for the enumeration of microorganisms
- ISO 4833-1:2013 Part 1: Colony count at 30 degrees C by the pour plate technique
- ISO 4833-2:2013 Part 2: Colony count at 30 degrees C by the surface plating technique
- ISO 4866:2010 Mechanical vibration and shock – Vibration of fixed structures – Guidelines for the measurement of vibrations and evaluation of their effects on structures
- ISO 4871:1996 Acoustics – Declaration and verification of noise emission values of machinery and equipment
- ISO/IEC 4873:1991 Information technology – ISO 8-bit code for information interchange – Structure and rules for implementation
- ISO 4875 Metal-cutting band saw blades
- ISO 4875-1:2006 Part 1: Vocabulary
- ISO 4880:1997 Burning behaviour of textiles and textile products - Vocabulary
- ISO 4882:1979 Office machines and data processing equipment - Line spacings and character spacings
- ISO 4885:2017 Ferrous materials - Heat treatments - Vocabulary
- ISO 4892 Plastics – Methods of exposure to laboratory light sources
- ISO 4902:1989 Information technology – Data communication – 37-pole DTE/DCE interface connector and contact number assignments
- ISO 4903:1989 Information technology – Data communication – 15-pole DTE/DCE interface connector and contact number assignments
- ISO/IEC 4909:2006 Identification cards - Financial transaction cards - Magnetic stripe data content for track 3
- ISO 4921:2000 Knitting – Basic concepts – Vocabulary
Notes
- ^ This list generally excludes draft versions.
- ^ ISO deliverables include "specifications" (ISO/PAS, ISO/TS), "reports" (ISO/TR), etc, which are not referred to by ISO as "standards".
- ^ a b c d e f g h i j k The exact wording of this title varies between parts. This is the wording of the most recently published part.